atomic_pool_expand iteratively tries the allocation while decrementing
the page order. There is no need to issue a warning if an attempted
allocation fails.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Fixes: d7e673ec2c8e ("dma-pool: Only allocate from CMA when in same memory zone")
[mszyprow: fixed typo] Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20251202152810.142370-1-dave.kleikamp@oracle.com Signed-off-by: Sasha Levin <sashal@kernel.org>
During system suspend, wakeup capable IRQs for block device can be
delayed, which can cause blk_mq_hctx_notify_offline() to hang
indefinitely while waiting for pending request to complete.
Skip the request waiting loop and abort suspend when wakeup events are
pending to prevent the deadlock.
Fixes: bf0beec0607d ("blk-mq: drain I/O when all CPUs in a hctx are offline") Signed-off-by: Cong Zhang <cong.zhang@oss.qualcomm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
bcm63xx_soc_pcm_new() does not check the return value of
of_dma_configure(), which may fail with -EPROBE_DEFER or
other errors, allowing PCM setup to continue with incomplete
DMA configuration.
Add error checking for of_dma_configure() and return on failure.
After commit 25524b619029 ("fs/nls: Fix utf16 to utf8 conversion"),
the return values of utf8_to_utf32() and utf32_to_utf8() are
inconsistent when encountering an error: utf8_to_utf32() returns -1,
while utf32_to_utf8() returns errno codes. Fix this inconsistency
by modifying utf8_to_utf32() to return errno codes as well.
Fixes: 25524b619029 ("fs/nls: Fix utf16 to utf8 conversion") Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com> Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://patch.msgid.link/20251129111535.8984-1-W_Armin@gmx.de Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This isn't ever used by VFS now, and it couldn't even work. Any FS that
uses the SECURITY_LSM_NATIVE_LABELS flag needs to also process the
value returned back from the LSM, so it needs to do its
security_sb_set_mnt_opts() call on its own anyway.
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Stable-dep-of: 8675c69816e4 ("NFS: Automounted filesystems should inherit ro,noexec,nodev,sync flags") Signed-off-by: Sasha Levin <sashal@kernel.org>
pnfs_set_layoutcommit relies on the lseg refcount to keep the layout
around. Need to clear NFS_INO_LAYOUTCOMMIT otherwise we might attempt
to reference a null layout.
Fixes: fe1cf9469d7bc ("pNFS: Clear all layout segment state in pnfs_mark_layout_stateid_invalid") Signed-off-by: Jonathan Curley <jcurley@purestorage.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the function responsible for converting between utf16 and
utf8 strings will ignore any characters that cannot be converted. This
however also includes multi-byte characters that do not fit into the
provided string buffer.
This can cause problems if such a multi-byte character is followed by
a single-byte character. In such a case the multi-byte character might
be ignored when the provided string buffer is too small, but the
single-byte character might fit and is thus still copied into the
resulting string.
Fix this by stop filling the provided string buffer once a character
does not fit. In order to be able to do this extend utf32_to_utf8()
to return useful errno codes instead of -1.
Fixes: 74675a58507e ("NLS: update handling of Unicode") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://patch.msgid.link/20251111131125.3379-2-W_Armin@gmx.de Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a file removal races with another operation that updates its
attributes, then skip the change to nlink, and just mark the attributes
as being stale.
Reported-by: Aiden Lambert <alambert48@gatech.edu> Fixes: 59a707b0d42e ("NFS: Ensure we revalidate the inode correctly after remove or rename") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
NFS unlink() (and rename over existing target) must determine if the
file is open, and must perform a "silly rename" instead of an unlink (or
before rename) if it is. Otherwise the client might hold a file open
which has been removed on the server.
Consequently if it determines that the file isn't open, it must block
any subsequent opens until the unlink/rename has been completed on the
server.
This is currently achieved by unhashing the dentry. This forces any
open attempt to the slow-path for lookup which will block on i_rwsem on
the directory until the unlink/rename completes. A future patch will
change the VFS to only get a shared lock on i_rwsem for unlink, so this
will no longer work.
Instead we introduce an explicit interlock. A special value is stored
in dentry->d_fsdata while the unlink/rename is running and
->d_revalidate blocks while that value is present. When ->d_revalidate
unblocks, the dentry will be invalid. This closes the race
without requiring exclusion on i_rwsem.
d_fsdata is already used in two different ways.
1/ an IS_ROOT directory dentry might have a "devname" stored in
d_fsdata. Such a dentry doesn't have a name and so cannot be the
target of unlink or rename. For safety we check if an old devname
is still stored, and remove it if it is.
2/ a dentry with DCACHE_NFSFS_RENAMED set will have a 'struct
nfs_unlinkdata' stored in d_fsdata. While this is set maydelete()
will fail, so an unlink or rename will never proceed on such
a dentry.
Neither of these can be in effect when a dentry is the target of unlink
or rename. So we can expect d_fsdata to be NULL, and store a special
value ((void*)1) which is given the name NFS_FSDATA_BLOCKED to indicate
that any lookup will be blocked.
The d_count() is incremented under d_lock() when a lookup finds the
dentry, so we check d_count() is low, and set NFS_FSDATA_BLOCKED under
the same lock to avoid any races.
After the success of an operation such as rmdir() or unlink(), we expect
to add the dentry back to the dcache as an ordinary negative dentry.
However in NFS, unless it is labelled with the appropriate verifier for
the parent directory state, then nfs_lookup_revalidate will end up
discarding that dentry and forcing a new lookup.
The fix is to ensure that we relabel the dentry appropriately on
success.
The page allocated for vmem using __get_free_pages() is not freed on the
error paths after it. Fix that by adding a corresponding __free_pages()
call to the error path.
pcs_pinconf_get() and pcs_pinconf_set() declare ret as unsigned int,
but assign it the return values of pcs_get_function() that may return
negative error codes. This causes negative error codes to be
converted to large positive values.
Change ret from unsigned int to int in both functions.
The pinctrl-single driver handles pin_config_set by looking up the
requested setting in a DT-defined lookup table, which defines what bits
correspond to each setting. There is no way to add
PIN_CONFIG_BIAS_DISABLE entries to the table, since there is instead
code to disable the bias by applying the disable values of both the
pullup and pulldown entries in the table.
However, this code is inside the table-lookup loop, so it would only
execute if there is an entry for PIN_CONFIG_BIAS_DISABLE in the table,
which can never exist, so this code never runs.
This commit lifts the offending code out of the loop, so it just
executes directly whenever PIN_CONFIG_BIAS_DISABLE is requested,
skippipng the table lookup loop.
This also introduces a new `param` variable to make the code slightly
more readable.
This bug seems to have existed when this code was first merged in commit 9dddb4df90d13 ("pinctrl: single: support generic pinconf"). Earlier
versions of this patch did have an entry for PIN_CONFIG_BIAS_DISABLE in
the lookup table, but that was removed, which is probably how this bug
was introduced.
In cake_drop(), qdisc_tree_reduce_backlog() is used to update the qlen
and backlog of the qdisc hierarchy. Its caller, cake_enqueue(), assumes
that the parent qdisc will enqueue the current packet. However, this
assumption breaks when cake_enqueue() returns NET_XMIT_CN: the parent
qdisc stops enqueuing current packet, leaving the tree qlen/backlog
accounting inconsistent. This mismatch can lead to a NULL dereference
(e.g., when the parent Qdisc is qfq_qdisc).
This patch computes the qlen/backlog delta in a more robust way by
observing the difference before and after the series of cake_drop()
calls, and then compensates the qdisc tree accounting if cake_enqueue()
returns NET_XMIT_CN.
To ensure correct compensation when ACK thinning is enabled, a new
variable is introduced to keep qlen unchanged.
Fixes: 15de71d06a40 ("net/sched: Make cake_enqueue return NET_XMIT_CN when past buffer_limit") Signed-off-by: Xiang Mei <xmei5@asu.edu> Reviewed-by: Toke Høiland-Jørgensen <toke@toke.dk> Link: https://patch.msgid.link/20251128001415.377823-1-xmei5@asu.edu Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "qcom,halt-regs" consists of a phandle reference followed by the
three offsets within syscon for halt registers. Thus, we need to
request 4 integers from of_property_read_variable_u32_array(), with
the halt_reg ofsets at indexes 1, 2, and 3. Offset 0 is the phandle.
With MAX_HALT_REG at 3, of_property_read_variable_u32_array() returns
-EOVERFLOW, causing .probe() to fail.
Increase MAX_HALT_REG to 4, and update the indexes accordingly.
Fixes: 0af65b9b915e ("remoteproc: qcom: wcss: Add non pas wcss Q6 support for QCS404") Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Link: https://lore.kernel.org/r/20251129013207.3981517-1-mr.nuke.me@gmail.com Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are several places where a value of type 'int' is shifted by
lpddr->chipshift. lpddr->chipshift is derived from QINFO geometry and
might reach 31 when QINFO reports a 2 GiB size - the maximum supported by
LPDDR(1) compliant chips. This may cause unexpected sign-extensions when
casting the integer value to the type of 'unsigned long'.
Use '1UL << lpddr->chipshift' and cast 'j' to unsigned long before
shifting so the computation is performed at the destination width.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c68264711ca6 ("[MTD] LPDDR Command set driver") Signed-off-by: Ivan Stepchenko <sid@itb.spb.ru> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The extra "count >= limit" check in stmmac_rx_zc() is redundant and
has no effect because the value of "count" doesn't change after the
while condition at this point.
However, it can change after "read_again:" label:
while (count < limit) {
...
if (count >= limit)
break;
read_again:
...
/* XSK pool expects RX frame 1:1 mapped to XSK buffer */
if (likely(status & rx_not_ls)) {
xsk_buff_free(buf->xdp);
buf->xdp = NULL;
dirty++;
count++;
goto read_again;
}
...
This patch addresses the same issue previously resolved in stmmac_rx()
by commit fa02de9e7588 ("net: stmmac: fix rx budget limit check").
The fix is the same: move the check after the label to ensure that it
bounds the goto loop.
Fixes: bba2556efad6 ("net: stmmac: Enable RX via AF_XDP zero-copy") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/20251126104327.175590-1-aleksei.kodanev@bell-sw.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Connlimit expression can be used for all kind of packets and not only
for packets with connection state new. See this ruleset as example:
table ip filter {
chain input {
type filter hook input priority filter; policy accept;
tcp dport 22 ct count over 4 counter
}
}
Currently, if the connection count goes over the limit the counter will
count the packets. When a connection is closed, the connection count
won't decrement as it should because it is only updated for new
connections due to an optimization on __nf_conncount_add() that prevents
updating the list if the connection is duplicated.
To solve this problem, check whether the connection was skipped and if
so, update the list. Adjust count_tree() too so the same fix is applied
for xt_connlimit.
Fixes: 976afca1ceba ("netfilter: nf_conncount: Early exit in nf_conncount_lookup() and cleanup") Closes: https://lore.kernel.org/netfilter/trinity-85c72a88-d762-46c3-be97-36f10e5d9796-1761173693813@3c-app-mailcom-bs12/ Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using nf_conncount infrastructure for non-confirmed connections a
duplicated track is possible due to an optimization introduced since
commit d265929930e2 ("netfilter: nf_conncount: reduce unnecessary GC").
In order to fix this introduce a new conncount API that receives
directly an sk_buff struct. It fetches the tuple and zone and the
corresponding ct from it. It comes with both existing conncount variants
nf_conncount_count_skb() and nf_conncount_add_skb(). In addition remove
the old API and adjust all the users to use the new one.
This way, for each sk_buff struct it is possible to check if there is a
ct present and already confirmed. If so, skip the add operation.
Fixes: d265929930e2 ("netfilter: nf_conncount: reduce unnecessary GC") Signed-off-by: Fernando Fernandez Mancera <fmancera@suse.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 69894e5b4c5e ("netfilter: nft_connlimit: update the count if add was skipped") Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently nf_conncount can trigger garbage collection (GC)
at multiple places. Each GC process takes a spin_lock_bh
to traverse the nf_conncount_list. We found that when testing
port scanning use two parallel nmap, because the number of
connection increase fast, the nf_conncount_count and its
subsequent call to __nf_conncount_add take too much time,
causing several CPU lockup. This happens when user set the
conntrack limit to +20,000, because the larger the limit,
the longer the list that GC has to traverse.
The patch mitigate the performance issue by avoiding unnecessary
GC with a timestamp. Whenever nf_conncount has done a GC,
a timestamp is updated, and beforce the next time GC is
triggered, we make sure it's more than a jiffies.
By doin this we can greatly reduce the CPU cycles and
avoid the softirq lockup.
To reproduce it in OVS,
$ ovs-appctl dpctl/ct-set-limits zone=1,limit=20000
$ ovs-appctl dpctl/ct-get-limits
At another machine, runs two nmap
$ nmap -p1- <IP>
$ nmap -p1- <IP>
Signed-off-by: William Tu <u9012063@gmail.com> Co-authored-by: Yifeng Sun <pkusunyifeng@gmail.com> Reported-by: Greg Rose <gvrose8192@gmail.com> Suggested-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Stable-dep-of: 69894e5b4c5e ("netfilter: nft_connlimit: update the count if add was skipped") Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator_supply_alias_list was accessed without any locking in
regulator_supply_alias(), regulator_register_supply_alias(), and
regulator_unregister_supply_alias(). Concurrent registration,
unregistration and lookups can race, leading to:
1 use-after-free if an alias entry is removed while being read,
2 duplicate entries when two threads register the same alias,
3 inconsistent alias mappings observed by consumers.
Protect all traversals, insertions and deletions on
regulator_supply_alias_list with the existing regulator_list_mutex.
Fixes: a06ccd9c3785f ("regulator: core: Add ability to create a lookup alias for supply") Signed-off-by: sparkhuang <huangshaobo3@xiaomi.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://patch.msgid.link/20251127025716.5440-1-huangshaobo3@xiaomi.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Rewrite the comment for better grammar and clarity.
Fixes: 75a0a52be3c2 ("virtio: introduce an API to set affinity for a virtqueue")
Message-Id: <e317e91bd43b070e5eaec0ebbe60c5749d02e2dd.1763026134.git.mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
virtio_vdpa_set_status() is declared as returning void, but it used
"return vdpa_set_status()" Since vdpa_set_status() also returns
void, the return statement is unnecessary and misleading.
Remove it.
Fixes: c043b4a8cf3b ("virtio: introduce a vDPA based transport") Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Message-Id: <20251001191653.1713923-1-alok.a.tiwari@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Subsequent patches enable get and set configuration either
via management device or via vdpa device' config ops.
This requires synchronization between multiple callers to get and set
config callbacks. Features setting also influence the layout of the
configuration fields endianness.
To avoid exposing synchronization primitives to callers, introduce
helper for setting the configuration and use it.
Signed-off-by: Parav Pandit <parav@nvidia.com> Reviewed-by: Eli Cohen <elic@nvidia.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/r/20211026175519.87795-2-parav@nvidia.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Stable-dep-of: e40b6abe0b12 ("virtio_vdpa: fix misleading return in void function") Signed-off-by: Sasha Levin <sashal@kernel.org>
When the MB_CHECK_ASSERT macro is enabled, we found that the
current validation logic in __mb_check_buddy has a gap in
detecting certain invalid buddy states, particularly related
to order-0 (bitmap) bits.
The original logic consists of three steps:
1. Validates higher-order buddies: if a higher-order bit is
set, at most one of the two corresponding lower-order bits
may be free; if a higher-order bit is clear, both lower-order
bits must be allocated (and their bitmap bits must be 0).
2. For any set bit in order-0, ensures all corresponding
higher-order bits are not free.
3. Verifies that all preallocated blocks (pa) in the group
have pa_pstart within bounds and their bitmap bits marked as
allocated.
However, this approach fails to properly validate cases where
order-0 bits are incorrectly cleared (0), allowing some invalid
configurations to pass:
corrupt integral
order 3 1 1
order 2 1 1 1 1
order 1 1 1 1 1 1 1 1 1
order 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Here we get two adjacent free blocks at order-0 with inconsistent
higher-order state, and the right one shows the correct scenario.
The root cause is insufficient validation of order-0 zero bits.
To fix this and improve completeness without significant performance
cost, we refine the logic:
1. Maintain the top-down higher-order validation, but we no longer
check the cases where the higher-order bit is 0, as this case will
be covered in step 2.
2. Enhance order-0 checking by examining pairs of bits:
- If either bit in a pair is set (1), all corresponding
higher-order bits must not be free.
- If both bits are clear (0), then exactly one of the
corresponding higher-order bits must be free
3. Keep the preallocation (pa) validation unchanged.
This change closes the validation gap, ensuring illegal buddy states
involving order-0 are correctly detected, while removing redundant
checks and maintaining efficiency.
Fixes: c9de560ded61f ("ext4: Add multi block allocator for ext4") Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Yongjian Sun <sunyongjian1@huawei.com> Reviewed-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz>
Message-ID: <20251106060614.631382-3-sunyongjian@huaweicloud.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Sasha Levin <sashal@kernel.org>
On all AMD AM4 systems I have seen, e.g ASUS X470-i, Pro WS X570 Ace
and equivalent Gigabyte, amd-pstate does not initialize when the
x2apic is enabled in the BIOS. Kernel debug messages include:
[ 0.315438] acpi LNXCPU:00: Failed to get CPU physical ID.
[ 0.354756] ACPI CPPC: No CPC descriptor for CPU:0
[ 0.714951] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled
I tracked this down to map_x2apic_id() checking device_declaration
passed in via the type argument of acpi_get_phys_id() via
map_madt_entry() while map_lapic_id() does not.
It appears these BIOSes use Processor statements for declaring the CPUs
in the ACPI namespace instead of processor device objects (which should
have been used). CPU declarations via Processor statements were
deprecated in ACPI 6.0 that was released 10 years ago. They should not
be used any more in any contemporary platform firmware.
I tried to contact Asus support multiple times, but never received a
reply nor did any BIOS update ever change this.
Fix amd-pstate w/ x2apic on am4 by allowing map_x2apic_id() to work with
CPUs declared via Processor statements for IDs less than 255, which is
consistent with ACPI 5.0 that still allowed Processor statements to be
used for declaring CPUs.
Fixes: 7237d3de78ff ("x86, ACPI: add support for x2apic ACPI extensions") Signed-off-by: René Rebe <rene@exactco.de>
[ rjw: Changelog edits ] Link: https://patch.msgid.link/20251126.165513.1373131139292726554.rene@exactco.de Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .H_SYNC_POLARITY and .V_SYNC_POLARITY variables are 1 bit bitfields
of a u32. The ATOM_HSYNC_POLARITY define is 0x2 and the
ATOM_VSYNC_POLARITY is 0x4. When we do a bitwise negate of 0, 2, or 4
then the last bit is always 1 so this code always sets .H_SYNC_POLARITY
and .V_SYNC_POLARITY to true.
This code is instead intended to check if the ATOM_HSYNC_POLARITY or
ATOM_VSYNC_POLARITY flags are set and reverse the result. In other
words, it's supposed to be a logical negate instead of a bitwise negate.
Fixes: ae79c310b1a6 ("drm/amd/display: Add DCE12 bios parser support") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
memset_io() writes memory byte by byte with __raw_writeb() on the arm
platform if the size is word. but XCVR data RAM memory can't be accessed
with byte address, so with memset_io() the channel status control memory
is not really cleared, use writel_relaxed() instead.
Fixes: 28564486866f ("ASoC: fsl_xcvr: Add XCVR ASoC CPU DAI driver") Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://patch.msgid.link/20251126064509.1900974-1-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add compatible string and specific soc data to support XCVR on i.MX93
platform. XCVR IP on i.MX93 is cut to SPDIF only by removing external
PHY.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com> Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com> Link: https://lore.kernel.org/r/20230104023953.2973362-3-chancel.liu@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 73b97d46dde6 ("ASoC: fsl_xcvr: clear the channel status control memory") Signed-off-by: Sasha Levin <sashal@kernel.org>
These counter registers are part of register list,
add them to complete the register map
- DMAC counter control registers
- Data path Timestamp counter register
- Data path bit counter register
- Data path bit count timestamp register
- Data path bit read timestamp register
Adds a lock around irdma_sc_ccq_arm body to prevent inter-thread data race.
Fixes data race in irdma_sc_ccq_arm() reported by KCSAN:
BUG: KCSAN: data-race in irdma_sc_ccq_arm [irdma] / irdma_sc_ccq_arm [irdma]
read to 0xffff9d51b4034220 of 8 bytes by task 255 on cpu 11:
irdma_sc_ccq_arm+0x36/0xd0 [irdma]
irdma_cqp_ce_handler+0x300/0x310 [irdma]
cqp_compl_worker+0x2a/0x40 [irdma]
process_one_work+0x402/0x7e0
worker_thread+0xb3/0x6d0
kthread+0x178/0x1a0
ret_from_fork+0x2c/0x50
write to 0xffff9d51b4034220 of 8 bytes by task 89 on cpu 3:
irdma_sc_ccq_arm+0x7e/0xd0 [irdma]
irdma_cqp_ce_handler+0x300/0x310 [irdma]
irdma_wait_event+0xd4/0x3e0 [irdma]
irdma_handle_cqp_op+0xa5/0x220 [irdma]
irdma_hw_flush_wqes+0xb1/0x300 [irdma]
irdma_flush_wqes+0x22e/0x3a0 [irdma]
irdma_cm_disconn_true+0x4c7/0x5d0 [irdma]
irdma_disconnect_worker+0x35/0x50 [irdma]
process_one_work+0x402/0x7e0
worker_thread+0xb3/0x6d0
kthread+0x178/0x1a0
ret_from_fork+0x2c/0x50
value changed: 0x0000000000024000 -> 0x0000000000034000
Some platforms (e.g. SC8280XP and X1E) support more than 128 stream
matching groups. This is more than what is defined as maximum by the ARM
SMMU architecture specification. Commit 122611347326 ("iommu/arm-smmu-qcom:
Limit the SMR groups to 128") disabled use of the additional groups because
they don't exhibit the same behavior as the architecture supported ones.
It seems like this is just another quirk of the hypervisor: When running
bare-metal without the hypervisor, the additional groups appear to behave
just like all others. The boot firmware uses some of the additional groups,
so ignoring them in this situation leads to stream match conflicts whenever
we allocate a new SMR group for the same SID.
The workaround exists primarily because the bypass quirk detection fails
when using a S2CR register from the additional matching groups, so let's
perform the test with the last reliable S2CR (127) and then limit the
number of SMR groups only if we detect that we are running below the
hypervisor (because of the bypass quirk).
Fixes: 122611347326 ("iommu/arm-smmu-qcom: Limit the SMR groups to 128") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a missing struct short description and a missing leading " *" to
lp855x.h to avoid kernel-doc warnings:
Warning: include/linux/platform_data/lp855x.h:126 missing initial short
description on line:
* struct lp855x_platform_data
Warning: include/linux/platform_data/lp855x.h:131 bad line:
Only valid when mode is PWM_BASED.
Fixes: 7be865ab8634 ("backlight: new backlight driver for LP855x devices") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reviewed-by: Daniel Thompson (RISCstar) <danielt@kernel.org> Link: https://patch.msgid.link/20251111060916.1995920-1-rdunlap@infradead.org Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
LED Backlight is a consumer of one or multiple LED class devices, but
devlink is currently unable to create correct supplier-producer links when
the supplier is a class device. It creates instead a link where the
supplier is the parent of the expected device.
One consequence is that removal order is not correctly enforced.
Issues happen for example with the following sections in a device tree
overlay:
// An LED driver chip
pca9632@62 {
compatible = "nxp,pca9632";
reg = <0x62>;
In this example, the devlink should be created between the backlight-addon
(consumer) and the pca9632@62 (supplier). Instead it is created between the
backlight-addon (consumer) and the parent of the pca9632@62, which is
typically the I2C bus adapter.
On removal of the above overlay, the LED driver can be removed before the
backlight device, resulting in:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
...
Call trace:
led_put+0xe0/0x140
devm_led_release+0x6c/0x98
Another way to reproduce the bug without any device tree overlays is
unbinding the LED class device (pca9632@62) before unbinding the consumer
(backlight-addon):
The FILS status codes are set to 108/109, but the IEEE 802.11-2020
spec defines them as 112/113. Update the enum so it matches the
specification and keeps the kernel consistent with standard values.
Fixes: a3caf7440ded ("cfg80211: Add support for FILS shared key authentication offload") Signed-off-by: Ria Thomas <ria.thomas@morsemicro.com> Reviewed-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Link: https://patch.msgid.link/20251124125637.3936154-1-ria.thomas@morsemicro.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fbtft_probe_common() allocates a memory chunk for "info" with
fbtft_framebuffer_alloc(). When "display->buswidth == 0" is true, the
function returns without releasing the "info", which will lead to a
memory leak.
Fix it by calling fbtft_framebuffer_release() when "display->buswidth
== 0" is true.
In mt7615_mcu_wtbl_sta_add(), an skb sskb is allocated. If the
subsequent call to mt76_connac_mcu_alloc_wtbl_req() fails, the function
returns an error without freeing sskb, leading to a memory leak.
Fix this by calling dev_kfree_skb() on sskb in the error handling path
to ensure it is properly released.
Fixes: 99c457d902cf9 ("mt76: mt7615: move mt7615_mcu_set_bmc to mt7615_mcu_ops") Signed-off-by: Zilin Guan <zilin@seu.edu.cn> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://patch.msgid.link/20251113062415.103611-1-zilin@seu.edu.cn Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix error handling in cc_map_hash_request_update where sg_nents_for_len
return value was assigned to u32, converting negative errors to large
positive values before passing to sg_copy_to_buffer.
Check sg_nents_for_len return value and propagate errors before
assigning to areq_ctx->in_nents.
Fixes: b7ec8530687a ("crypto: ccree - use std api when possible") Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, test_perf_branches_no_hw() relies on the busy loop within
test_perf_branches_common() being slow enough to allow at least one
perf event sample tick to occur before starting to tear down the
backing perf event BPF program. With a relatively small fixed
iteration count of 1,000,000, this is not guaranteed on modern fast
CPUs, resulting in the test run to subsequently fail with the
following:
On a modern CPU (i.e. one with a 3.5 GHz clock rate), executing 1
million increments of a volatile integer can take significantly less
than 1 millisecond. If the spin loop and detachment of the perf event
BPF program elapses before the first 1 ms sampling interval elapses,
the perf event will never end up firing. Fix this by bumping the loop
iteration counter a little within test_perf_branches_common(), along
with ensuring adding another loop termination condition which is
directly influenced by the backing perf event BPF program
executing. Notably, a concious decision was made to not adjust the
sample_freq value as that is just not a reliable way to go about
fixing the problem. It effectively still leaves the race window open.
Gracefully skip the test_perf_branches_hw subtest on platforms that
do not support LBR or require specialized perf event attributes
to enable branch sampling.
For example, AMD's Milan (Zen 3) supports BRS rather than traditional
LBR. This requires specific configurations (attr.type = PERF_TYPE_RAW,
attr.config = RETIRED_TAKEN_BRANCH_INSTRUCTIONS) that differ from the
generic setup used within this test. Notably, it also probably doesn't
hold much value to special case perf event configurations for selected
micro architectures.
Fixes: 67306f84ca78c ("selftests/bpf: Add bpf_read_branch_records() selftest") Signed-off-by: Matt Bobrowski <mattbobrowski@google.com> Acked-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20251120142059.2836181-1-mattbobrowski@google.com Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous commit removed the PAGE_SIZE limit on transfer length of
raw_io buffer in order to avoid any problems with emulating USB devices
whose full configuration descriptor exceeds PAGE_SIZE in length. However
this also removes the upperbound on user supplied length, allowing very
large values to be passed to the allocator.
syzbot on fuzzing the transfer length with very large value (1.81GB)
results in kmalloc() to fall back to the page allocator, which triggers
a kernel warning as the page allocator cannot handle allocations more
than MAX_PAGE_ORDER/KMALLOC_MAX_SIZE.
Since there is no limit imposed on the size of buffer for both control
and non control transfers, cap the raw_io transfer length to
KMALLOC_MAX_SIZE and return -EINVAL for larger transfer length to
prevent any warnings from the page allocator.
dwc2 on most platforms needs phy controller, clock and power supply.
All of them must be enabled/activated to properly operate. If dwc2
is configured as peripheral mode, then all the above three hardware
resources are disabled at the end of the probe:
/* Gadget code manages lowlevel hw on its own */
if (hsotg->dr_mode == USB_DR_MODE_PERIPHERAL)
dwc2_lowlevel_hw_disable(hsotg);
But the dwc2_suspend() tries to read the dwc2's reg to check whether
is_device_mode or not, this would result in hang during suspend if dwc2
is configured as peripheral mode.
Fix this hang by bypassing suspend/resume if lowlevel hw isn't
enabled.
dwc2 on most platforms needs phy controller, clock and power supply.
All of them must be enabled/activated to properly operate. If dwc2
is configured as peripheral mode, then all the above three hardware
resources are disabled at the end of the probe:
/* Gadget code manages lowlevel hw on its own */
if (hsotg->dr_mode == USB_DR_MODE_PERIPHERAL)
dwc2_lowlevel_hw_disable(hsotg);
But dwc2_driver_shutdown() tries to disable the interrupts on HW IP
level. This would result in hang during shutdown if dwc2 is configured
as peripheral mode.
Fix this hang by only disable and sync irq when lowlevel hw is enabled.
On some SoC platforms, in shutdown stage, most components' power is cut
off, but there's still power supply to the so called always-on
domain, so if the dwc2's regulator is from the always-on domain, we
need to explicitly disable it to save power.
Disable platform lowlevel hw resources such as phy, clock and
regulators etc. in device shutdown hook to reduce non-necessary power
consumption when the platform enters shutdown stage.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org> Acked-by: Minas Harutyunyan <hminas@synopsys.com> Link: https://lore.kernel.org/r/20250629094655.747-1-jszhang@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b6ebcfdcac40 ("usb: dwc2: fix hang during shutdown if set as peripheral") Signed-off-by: Sasha Levin <sashal@kernel.org>
In ima_match_rules(), if ima_filter_rule_match() returns -ENOENT due to
the rule being NULL, the function incorrectly skips the 'if (!rc)' check
and sets 'result = true'. The LSM rule is considered a match, causing
extra files to be measured by IMA.
This issue can be reproduced in the following scenario:
After unloading the SELinux policy module via 'semodule -d', if an IMA
measurement is triggered before ima_lsm_rules is updated,
in ima_match_rules(), the first call to ima_filter_rule_match() returns
-ESTALE. This causes the code to enter the 'if (rc == -ESTALE &&
!rule_reinitialized)' block, perform ima_lsm_copy_rule() and retry. In
ima_lsm_copy_rule(), since the SELinux module has been removed, the rule
becomes NULL, and the second call to ima_filter_rule_match() returns
-ENOENT. This bypasses the 'if (!rc)' check and results in a false match.
Fix this by changing 'if (!rc)' to 'if (rc <= 0)' to ensure that error
codes like -ENOENT do not bypass the check and accidentally result in a
successful match.
The rtl8187_rx_cb() calculates the rx descriptor header address
by subtracting its size from the skb tail pointer.
However, it does not validate if the received packet
(skb->len from urb->actual_length) is large enough to contain this
header.
If a truncated packet is received, this will lead to a buffer
underflow, reading memory before the start of the skb data area,
and causing a kernel panic.
Add length checks for both rtl8187 and rtl8187b descriptor headers
before attempting to access them, dropping the packet cleanly if the
check fails.
If devm_request_threaded_irq() fails after irq_domain_add_linear()
succeeds in mt6358_irq_init(), the function returns without removing
the created IRQ domain, leading to a resource leak.
Call irq_domain_remove() in the error path after a successful
irq_domain_add_linear() to properly release the IRQ domain.
Fixes: 2b91c28f2abd ("mfd: Add support for the MediaTek MT6358 PMIC") Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn> Link: https://patch.msgid.link/20251118121427.583-1-vulab@iscas.ac.cn Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If devm_request_threaded_irq() fails after irq_domain_create_linear()
succeeds in mt6397_irq_init(), the function returns without removing
the created IRQ domain, leading to a resource leak.
Call irq_domain_remove() in the error path after a successful
irq_domain_create_linear() to properly release the IRQ domain.
Fixes: a4872e80ce7d ("mfd: mt6397: Extract IRQ related code from core driver") Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn> Link: https://patch.msgid.link/20251118121500.605-1-vulab@iscas.ac.cn Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .free callback cleared among others the enable bit PWENx in the
control register. When the PWM is requested later again this bit isn't
restored but the core assumes the PWM is enabled and thus skips a
request to configure the same state as before.
To fix that don't touch the hardware configuration in .free(). For
symmetry also drop .request() and configure the mode completely in
.apply().
if matrixbit is 11,
The range of color matrix is from 0 to (BIT(12) - 1).
Values from 0 to (BIT(11) - 1) represent positive numbers,
values from BIT(11) to (BIT(12) - 1) represent negative numbers.
For example, -1 need converted to 8191.
so convert S31.32 to HW Q2.11 format by drm_color_ctm_s31_32_to_qm_n,
and set int_bits to 2.
Fixes: 738ed4156fba ("drm/mediatek: Add matrix_bits private data for ccorr") Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Jay Liu <jay.liu@mediatek.com> Link: https://patchwork.kernel.org/project/dri-devel/patch/20250921055416.25588-2-jay.liu@mediatek.com/ Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a rb node with the same ino already exists in the rb tree, the newly
alloced mft_inode in ni_add_subrecord() will not have its memory cleaned
up, which leads to the memory leak issue reported by syzbot.
The best option to avoid this issue is to put the newly alloced mft node
when a rb node with the same ino already exists in the rb tree and return
the rb node found in the rb tree to the parent layer.
Fixes: 4342306f0f0d ("fs/ntfs3: Add file operations and implementation") Reported-by: syzbot+3932ccb896e06f7414c9@syzkaller.appspotmail.com Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After ntfs_look_free_mft() executes successfully, all subsequent code
that fails to execute must put mi.
Fixes: 4342306f0f0d ("fs/ntfs3: Add file operations and implementation") Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function ni_ins_new_attr now returns ERR_PTR(err),
so we check it now in other functions like ni_expand_mft_list
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Stable-dep-of: 4d78d1173a65 ("fs/ntfs3: out1 also needs to put mi") Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Stable-dep-of: 4d78d1173a65 ("fs/ntfs3: out1 also needs to put mi") Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Stable-dep-of: 4d78d1173a65 ("fs/ntfs3: out1 also needs to put mi") Signed-off-by: Sasha Levin <sashal@kernel.org>
HPTE format was changed since Power9 (ISA 3.0) onwards. While dumping
kernel hash page tables, nothing gets printed on powernv P9+. This patch
utilizes the helpers added in the patch tagged as fixes, to convert new
format to old format and dump the hptes. This fix is only needed for
native_find() (powernv), since pseries continues to work fine with the
old format.
In rtl8180_init_rx_ring(), memory is allocated for skb packets and DMA
allocations in a loop. When an allocation fails, the previously
successful allocations are not freed on exit.
Fix that by jumping to err_free_rings label on error, which calls
rtl8180_free_rx_ring() to free the allocations. Remove the free of
rx_ring in rtl8180_init_rx_ring() error path, and set the freed
priv->rx_buf entry to null, to avoid double free.
The extent returned by the file system may have a smaller offset than
the segment offset requested by the client. In this case, the minimum
segment length must be checked against the requested range. Otherwise,
the client may not be able to continue the read/write operation.
wdat_wdt_probe() calls acpi_get_table() to obtain the WDAT ACPI table but
never calls acpi_put_table() on any paths. This causes a permanent ACPI
table memory leak.
Add a single cleanup path which calls acpi_put_table() to ensure
the ACPI table is always released.
When test_send_signal_kern__open_and_load() fails parent closes the
pipe which cases ASSERT_EQ(read(pipe_p2c...)) to fail, but child
continues and enters infinite loop, while parent is stuck in wait(NULL).
Other error paths have similar issue, so kill the child before waiting on it.
The bug was discovered while compiling all of selftests with -O1 instead of -O2
which caused progs/test_send_signal_kern.c to fail to load.
With 6e0a48552b8c (ps3disk: use memcpy_{from,to}_bvec) converting
ps3disk to new bvec helpers, incrementing the offset was accidently
lost, corrupting consecutive buffers. Restore index for non-corrupted
data transfers.
Fixes: 6e0a48552b8c (ps3disk: use memcpy_{from,to}_bvec) Signed-off-by: René Rebe <rene@exactco.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit under Fixes introduced support for PCIe EP mode on AM654x platforms.
When the mode happens to be either "DW_PCIE_RC_TYPE" or "DW_PCIE_EP_TYPE",
the PCIe Controller is configured accordingly. However, when the mode is
neither of them, an error message is displayed, but the driver probe
succeeds. Since this "invalid" mode is not associated with a functional
PCIe Controller, the probe should fail.
Fix the behavior by exiting "ks_pcie_probe()" with the return value of
"-EINVAL" in addition to displaying the existing error message when the
mode is invalid.
Fixes: 23284ad677a9 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms") Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com> Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Link: https://patch.msgid.link/20251029080547.1253757-4-s-vadapalli@ti.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The function netxbig_gpio_ext_get() acquires GPIO descriptors but
fails to release them when errors occur mid-way through initialization.
The cleanup callback registered by devm_add_action_or_reset() only
runs on success, leaving acquired GPIOs leaked on error paths.
Add goto-based error handling to release all acquired GPIOs before
returning errors.
Fixes: 9af512e81964 ("leds: netxbig: Convert to use GPIO descriptors") Suggested-by: Markus Elfring <Markus.Elfring@web.de> Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn> Link: https://patch.msgid.link/20251031021620.781-1-vulab@iscas.ac.cn Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver calls ioport_map() to map I/O ports in sim710_probe_common()
but never calls ioport_unmap() to release the mapping. This causes
resource leaks in both the error path when request_irq() fails and in
the normal device removal path via sim710_device_remove().
Add ioport_unmap() calls in the out_release error path and in
sim710_device_remove().
Fixes: 56fece20086e ("[PATCH] finally fix 53c700 to use the generic iomem infrastructure") Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn> Link: https://patch.msgid.link/20251029032555.1476-1-vulab@iscas.ac.cn Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
acpi_fwnode_graph_parse_endpoint() calls fwnode_get_parent() to obtain the
parent fwnode but returns without calling fwnode_handle_put() on it. This
potentially leads to a fwnode refcount leak and prevents the parent node
from being released properly.
Call fwnode_handle_put() on the parent fwnode before returning to prevent
the leak from occurring.
Fixes: 3b27d00e7b6d ("device property: Move fwnode graph ops to firmware specific locations") Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn> Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[ rjw: Changelog edits ] Link: https://patch.msgid.link/20251111075000.1828-1-vulab@iscas.ac.cn Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In '__ocfs2_move_extent()', relax 'BUG()' to 'ocfs2_error()' just
to avoid crashing the whole kernel due to a filesystem corruption.
Fixes: 8f603e567aa7 ("Ocfs2/move_extents: move a range of extent.") Link: https://lkml.kernel.org/r/20251009102349.181126-2-dmantipov@yandex.ru Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Closes: https://syzkaller.appspot.com/bug?extid=727d161855d11d81e411 Reported-by: syzbot+727d161855d11d81e411@syzkaller.appspotmail.com Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code uses of_iomap() to map registers but never calls
iounmap() on any error path after the mapping. This causes a memory
leak when probe fails after successful ioremap, for example when
of_clk_add_provider() or r9a06g032_add_clk_domain() fails.
Replace of_iomap() with devm_of_iomap() to automatically unmap the
region on probe failure. Update the error check accordingly to use
IS_ERR() and PTR_ERR() since devm_of_iomap() returns ERR_PTR on error.
The trace unit is controlled in the ETM hardware enabling and disabling.
The sequential changes for support AUX pause and resume will reuse the
same operations.
Extract the operations in the etm4_{enable|disable}_trace_unit()
functions. A minor improvement in etm4_enable_trace_unit() is for
returning the timeout error to callers.
Signed-off-by: Leo Yan <leo.yan@arm.com> Reviewed-by: Mike Leach <mike.leach@linaro.org> Reviewed-by: James Clark <james.clark@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20250401180708.385396-2-leo.yan@arm.com
Stable-dep-of: 64eb04ae5452 ("coresight: etm4x: Add context synchronization before enabling trace") Signed-off-by: Sasha Levin <sashal@kernel.org>
As recommended by section 4.3.7 ("Synchronization when using system
instructions to progrom the trace unit") of ARM IHI 0064H.b, the
self-hosted trace analyzer must perform a Context synchronization
event between writing to the TRCPRGCTLR and reading the TRCSTATR.
Additionally, add an ISB between the each read of TRCSTATR on
coresight_timeout() when using system instructions to program the
trace unit.
The Trace Filtering support (FEAT_TRF) ensures that the ETM
can be prohibited from generating any trace for a given EL.
This is much stricter knob, than the TRCVICTLR exception level
masks, which doesn't prevent the ETM from generating Context
packets for an "excluded" EL. At the moment, we do a onetime
enable trace at user and kernel and leave it untouched for the
kernel life time. This implies that the ETM could potentially
generate trace packets containing the kernel addresses, and
thus leaking the kernel virtual address in the trace.
This patch makes the switch dynamic, by honoring the filters
set by the user and enforcing them in the TRFCR controls.
We also rename the cpu_enable_tracing() appropriately to
cpu_detect_trace_filtering() and the drvdata member
trfc => trfcr to indicate the "value" of the TRFCR_EL1.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Al Grant <al.grant@arm.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20210914102641.1852544-3-suzuki.poulose@arm.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Stable-dep-of: 64eb04ae5452 ("coresight: etm4x: Add context synchronization before enabling trace") Signed-off-by: Sasha Levin <sashal@kernel.org>
When the CPU enters a low power mode, the TRFCR_EL1 contents could be
reset. Thus we need to save/restore the TRFCR_EL1 along with the ETM4x
registers to allow the tracing.
The TRFCR related helpers are in a new header file, as we need to use
them for TRBE in the later patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Mike Leach <mike.leach@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20210914102641.1852544-2-suzuki.poulose@arm.com
[Fixed cosmetic details] Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Stable-dep-of: 64eb04ae5452 ("coresight: etm4x: Add context synchronization before enabling trace") Signed-off-by: Sasha Levin <sashal@kernel.org>
The WARNING occurs when two processes concurrently write to the mac-hid
emulation sysctl, causing a race condition in mac_hid_toggle_emumouse().
Both processes read old_val=0, then both try to register the input handler,
leading to a double list_add of the same handler.
Commit b96bae3ae2cb ("powerpc/32: Replace ASM exception exit by C
exception exit from ppc64") erroneouly copied to powerpc/32 the logic
from powerpc/64 based on feature CPU_FTR_STCX_CHECKS_ADDRESS which is
always 0 on powerpc/32.
Re-instate the logic implemented by commit b64f87c16f3c ("[POWERPC]
Avoid unpaired stwcx. on some processors") which is based on
CPU_FTR_NEED_PAIRED_STWCX feature.
projects / thirdparty / kernel / stable.git / log
