The debounce time passed to gpiod_set_debounce() is specified in
microseconds, so make sure to use the correct unit when computing the
register values, which denote delays in milliseconds.
Signed-off-by: Thierry Reding <treding@nvidia.com> Cc: <stable@vger.kernel.org> Fixes: 18bc64b3aebf ("gpio: Initial support for ROHM bd70528 GPIO block")
[Bartosz: fixed a typo in commit message] Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When converting milliseconds to microseconds in commit fffa6af94894
("gpio: max77620: Use correct unit for debounce times") some ~1 ms gaps
were introduced between the various ranges supported by the controller.
Fix this by changing the start of each range to the value immediately
following the end of the previous range. This way a debounce time of,
say 8250 us will translate into 16 ms instead of returning an -EINVAL
error.
Typically the debounce delay is only ever set through device tree and
specified in milliseconds, so we can never really hit this issue because
debounce times are always a multiple of 1000 us.
The only notable exception for this is drivers/mmc/host/mmc-spi.c where
the CD GPIO is requested, which passes a 1 us debounce time. According
to a comment preceeding that code this should actually be 1 ms (i.e.
1000 us).
If the packets to sent to the guest are bigger than the buffer
available, we can split them, using multiple buffers and fixing
the length in the packet header.
This is safe since virtio-vsock supports only stream sockets.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 85327a9c4150 ("net/mlx5: Update the list of the PCI supported devices") Signed-off-by: Shani Shapp <shanish@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some old Firmwares, connector type value was not supported, and value
read from FW was 0. For those, driver used link mode in order to set
connector type in link_ksetting.
After FW exposed the connector type, driver translated the value to ethtool
definitions. However, as 0 is a valid value, before returning PORT_OTHER,
driver run the check of link mode in order to maintain backward
compatibility.
Cited patch added support to EXT mode. With both features (connector type
and EXT link modes) ,if connector_type read from FW is 0 and EXT mode is
set, driver mistakenly compare EXT link modes to non-EXT link mode.
Fixed that by skipping this comparison if we are in EXT mode, as connector
type value is valid in this scenario.
Fixes: 6a897372417e ("net/mlx5: ethtool, Add ethtool support for 50Gbps per lane link modes") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit eec4844fae7c ("proc/sysctl: add shared variables for range
check") did:
- .extra2 = &two,
+ .extra2 = SYSCTL_ONE,
here, which doesn't seem to be intentional, given the changelog.
This patch restores it to the previous, as the value of 2 still makes
sense (used in fib_multipath_hash()).
Fixes: eec4844fae7c ("proc/sysctl: add shared variables for range check") Cc: Matteo Croce <mcroce@redhat.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The taprio qdisc allows to set mqprio setting but only once. In case
if mqprio settings are provided next time the error is returned as
it's not allowed to change traffic class mapping in-flignt and that
is normal. But if configuration is absolutely the same - no need to
return error. It allows to provide same command couple times,
changing only base time for instance, or changing only scheds maps,
but leaving mqprio setting w/o modification. It more corresponds the
message: "Changing the traffic mapping of a running schedule is not
supported", so reject mqprio if it's really changed.
Also corrected TC_BITMASK + 1 for consistency, as proposed.
Fixes: a3d43c0d56f1 ("taprio: Add support adding an admin schedule") Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Tested-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously we will return directly if (!rt || !rt->fib6_nh.fib_nh_gw_family)
in function rt6_probe(), but after commit cc3a86c802f0
("ipv6: Change rt6_probe to take a fib6_nh"), the logic changed to
return if there is fib_nh_gw_family.
Fixes: cc3a86c802f0 ("ipv6: Change rt6_probe to take a fib6_nh") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once all the large flow groups (defined by the user when the flow table
is created - max_num_groups) were created, then all the following new
flow groups will have only one flow table entry, even though the flow table
has place to larger groups.
Fix the condition to prefer large flow group.
Array mlxfw_fsm_state_err_str contains value to string translation, when
values are provided by mlxfw_dev. If value is larger than
MLXFW_FSM_STATE_ERR_MAX, return "unknown error" as expected instead of
reading an address than exceed array size.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workqueue only exists for the primary PF. For other functions
we hit a WARN_ON in kernel/workqueue.c.
Fixes: 7c236c43b838 ("sfc: Add support for IEEE-1588 PTP") Signed-off-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
info->options_len is 'u8' type, and when opts_len with a value >
IP_TUNNEL_OPTS_MAX, 'info->options_len = opts_len' will cast int
to u8 and set a wrong value to info->options_len.
Kernel crashed in my test when doing:
# opts="0102:80:00800022"
# for i in {1..99}; do opts="$opts,0102:80:00800022"; done
# ip link add name geneve0 type geneve dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 ip_proto udp action tunnel_key \
set src_ip 10.0.99.192 dst_ip 10.0.99.193 \
dst_port 6081 id 11 geneve_opts $opts \
action mirred egress redirect dev geneve0
So we should do the similar check as cls_flower does, return error
when opts_len > IP_TUNNEL_OPTS_MAX in tunnel_key_copy_opts().
Fixes: 0ed5269f9e41 ("net/sched: add tunnel option support to act_tunnel_key") Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when configuring act_pedit rules, the number of keys is validated only on
addition of a new entry. This is not sufficient to avoid hitting a WARN()
in the traffic path: for example, it is possible to replace a valid entry
with a new one having 0 extended keys, thus causing splats in dmesg like:
The "ivm->vf" variable is a u32, but the problem is that a number of
drivers cast it to an int and then forget to check for negatives. An
example of this is in the cxgb4 driver.
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8435 hclge_set_vf_vlan_filter() warn: can 'vfid' underflow 's32min-2147483646'
drivers/net/ethernet/freescale/enetc/enetc_pf.c:377 enetc_pf_set_vf_mac() warn: can 'vf' underflow 's32min-2147483646'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2899 cxgb4_mgmt_get_vf_config() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:2960 cxgb4_mgmt_set_vf_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3019 cxgb4_mgmt_set_vf_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3038 cxgb4_mgmt_set_vf_vlan() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c:3086 cxgb4_mgmt_set_vf_link_state() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/chelsio/cxgb/cxgb2.c:791 get_eeprom() warn: can 'i' underflow 's32min-(-4),0,4-s32max'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:82 bnxt_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:164 bnxt_set_vf_trust() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:186 bnxt_get_vf_config() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:228 bnxt_set_vf_mac() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:264 bnxt_set_vf_vlan() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:293 bnxt_set_vf_bw() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnxt/bnxt_sriov.c:333 bnxt_set_vf_link_state() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:2595 bnx2x_vf_op_prep() warn: can 'vfidx' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:2595 bnx2x_vf_op_prep() warn: can 'vfidx' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2281 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2285 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2286 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2292 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_vfpf.c:2297 bnx2x_post_vf_bulletin() warn: can 'vf' underflow 's32min-63'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1832 qlcnic_sriov_set_vf_mac() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1864 qlcnic_sriov_set_vf_tx_rate() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1937 qlcnic_sriov_set_vf_vlan() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:2005 qlcnic_sriov_get_vf_config() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:2036 qlcnic_sriov_set_vf_spoofchk() warn: can 'vf' underflow 's32min-254'
drivers/net/ethernet/emulex/benet/be_main.c:1914 be_get_vf_config() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1915 be_get_vf_config() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1922 be_set_vf_tvt() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:1951 be_clear_vf_tvt() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:2063 be_set_vf_tx_rate() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/emulex/benet/be_main.c:2091 be_set_vf_link_state() warn: can 'vf' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:2609 ice_set_vf_port_vlan() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3050 ice_get_vf_cfg() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3103 ice_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3181 ice_set_vf_mac() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3237 ice_set_vf_trust() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/ice/ice_virtchnl_pf.c:3286 ice_set_vf_link_state() warn: can 'vf_id' underflow 's32min-65534'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:3919 i40e_validate_vf() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:3957 i40e_ndo_set_vf_mac() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4104 i40e_ndo_set_vf_port_vlan() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4263 i40e_ndo_set_vf_bw() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4309 i40e_ndo_get_vf_config() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4371 i40e_ndo_set_vf_link_state() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4441 i40e_ndo_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4441 i40e_ndo_set_vf_spoofchk() warn: can 'vf_id' underflow 's32min-2147483646'
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:4504 i40e_ndo_set_vf_trust() warn: can 'vf_id' underflow 's32min-2147483646'
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
XDP_TX rings should not be limited by max_num_tx_rings_p_up.
To make sure total number of TX rings never exceed MAX_TX_RINGS,
add similar check in mlx4_en_alloc_tx_queue_per_tc(), where
a new value is assigned for num_up.
Fixes: 7e1dc5e926d5 ("net/mlx4_en: Limit the number of TX rings") Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ethtool expects ETHTOOL_GRXCLSRLALL to set ethtool_rxnfc->data with the
total number of entries in the rx classifier table. Surprisingly, mlx4
is missing this part (in principle ethtool could still move forward and
try the insert).
Tested: compiled and run command:
phh13:~# ethtool -N eth1 flow-type udp4 queue 4
Added rule with ID 255
The helper mlxsw_sp_ipip_dev_ul_tb_id() determines the underlay VRF of a
GRE tunnel. For a tunnel without a bound device, it uses the same VRF that
the tunnel is in. However in Linux, a GRE tunnel without a bound device
uses the main VRF as the underlay. Fix the function accordingly.
mlxsw further assumed that moving a tunnel to a different VRF could cause
conflict in local tunnel endpoint address, which cannot be offloaded.
However, the only way that an underlay could be changed by moving the
tunnel device itself is if the tunnel device does not have a bound device.
But in that case the underlay is always the main VRF, so there is no
opportunity to introduce a conflict by moving such device. Thus this check
constitutes a dead code, and can be removed, which do.
Fixes: 6ddb7426a7d4 ("mlxsw: spectrum_router: Introduce loopback RIFs") Signed-off-by: Petr Machata <petrm@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also with this gone we can remove the cea_modes db. This entire thing
is massively incomplete anyway, compared to the CEA parsing that
drm_edid.c does.
A number of our uaccess routines ('__arch_clear_user()' and
'__arch_copy_{in,from,to}_user()') fail to re-enable PAN if they
encounter an unhandled fault whilst accessing userspace.
For CPUs implementing both hardware PAN and UAO, this bug has no effect
when both extensions are in use by the kernel.
For CPUs implementing hardware PAN but not UAO, this means that a kernel
using hardware PAN may execute portions of code with PAN inadvertently
disabled, opening us up to potential security vulnerabilities that rely
on userspace access from within the kernel which would usually be
prevented by this mechanism. In other words, parts of the kernel run the
same way as they would on a CPU without PAN implemented/emulated at all.
For CPUs not implementing hardware PAN and instead relying on software
emulation via 'CONFIG_ARM64_SW_TTBR0_PAN=y', the impact is unfortunately
much worse. Calling 'schedule()' with software PAN disabled means that
the next task will execute in the kernel using the page-table and ASID
of the previous process even after 'switch_mm()', since the actual
hardware switch is deferred until return to userspace. At this point, or
if there is a intermediate call to 'uaccess_enable()', the page-table
and ASID of the new process are installed. Sadly, due to the changes
introduced by KPTI, this is not an atomic operation and there is a very
small window (two instructions) where the CPU is configured with the
page-table of the old task and the ASID of the new task; a speculative
access in this state is disastrous because it would corrupt the TLB
entries for the new task with mappings from the previous address space.
As Pavel explains:
| I was able to reproduce memory corruption problem on Broadcom's SoC
| ARMv8-A like this:
|
| Enable software perf-events with PERF_SAMPLE_CALLCHAIN so userland's
| stack is accessed and copied.
|
| The test program performed the following on every CPU and forking
| many processes:
|
| unsigned long *map = mmap(NULL, PAGE_SIZE, PROT_READ|PROT_WRITE,
| MAP_SHARED | MAP_ANONYMOUS, -1, 0);
| map[0] = getpid();
| sched_yield();
| if (map[0] != getpid()) {
| fprintf(stderr, "Corruption detected!");
| }
| munmap(map, PAGE_SIZE);
|
| From time to time I was getting map[0] to contain pid for a
| different process.
Ensure that PAN is re-enabled when returning after an unhandled user
fault from our uaccess routines.
Cc: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Cc: <stable@vger.kernel.org> Fixes: 338d4f49d6f7 ("arm64: kernel: Add support for Privileged Access Never") Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: rewrote commit message] Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We recently started updating the node span based on the zone span to
avoid touching uninitialized memmaps.
Currently, we will always detect the node span to start at 0, meaning a
node can easily span too many pages. pgdat_is_empty() will still work
correctly if all zones span no pages. We should skip over all zones
without spanned pages and properly handle the first detected zone that
spans pages.
Unfortunately, in contrast to the zone span (/proc/zoneinfo), the node
span cannot easily be inspected and tested. The node span gives no real
guarantees when an architecture supports memory hotplug, meaning it can
easily contain holes or span pages of different nodes.
The node span is not really used after init on architectures that
support memory hotplug.
E.g., we use it in mm/memory_hotplug.c:try_offline_node() and in
mm/kmemleak.c:kmemleak_scan(). These users seem to be fine.
Link: http://lkml.kernel.org/r/20191027222714.5313-1-david@redhat.com Fixes: 00d6c019b5bc ("mm/memory_hotplug: don't access uninitialized memmaps in shrink_pgdat_span()") Signed-off-by: David Hildenbrand <david@redhat.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We might use the nid of memmaps that were never initialized. For
example, if the memmap was poisoned, we will crash the kernel in
pfn_to_nid() right now. Let's use the calculated boundaries of the
separate zones instead. This now also avoids having to iterate over a
whole bunch of subsections again, after shrinking one zone.
Before commit d0dc12e86b31 ("mm/memory_hotplug: optimize memory
hotplug"), the memmap was initialized to 0 and the node was set to the
right value. After that commit, the node might be garbage.
We'll have to fix shrink_zone_span() next.
Link: http://lkml.kernel.org/r/20191006085646.5768-4-david@redhat.com Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [d0dc12e86b319] Signed-off-by: David Hildenbrand <david@redhat.com> Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: David Hildenbrand <david@redhat.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Pavel Tatashin <pasha.tatashin@soleen.com> Cc: Dan Williams <dan.j.williams@intel.com> Cc: Wei Yang <richardw.yang@linux.intel.com> Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Damian Tometzki <damian.tometzki@gmail.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Halil Pasic <pasic@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jason Gunthorpe <jgg@ziepe.ca> Cc: Jun Yao <yaojun8558363@gmail.com> Cc: Logan Gunthorpe <logang@deltatee.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: "Matthew Wilcox (Oracle)" <willy@infradead.org> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Pankaj Gupta <pagupta@redhat.com> Cc: Paul Mackerras <paulus@samba.org> Cc: Pavel Tatashin <pavel.tatashin@microsoft.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Qian Cai <cai@lca.pw> Cc: Rich Felker <dalias@libc.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Steve Capper <steve.capper@arm.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Wei Yang <richard.weiyang@gmail.com> Cc: Will Deacon <will@kernel.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: Yu Zhao <yuzhao@google.com> Cc: <stable@vger.kernel.org> [4.13+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 3726112ec731 ("block, bfq: re-schedule empty queues if
they deserve I/O plugging"), to prevent the service guarantees of a
bfq_queue from being violated, the bfq_queue may be left busy, i.e.,
scheduled for service, even if empty (see comments in
__bfq_bfqq_expire() for details). But, if no process will send
requests to the bfq_queue any longer, then there is no point in
keeping the bfq_queue scheduled for service.
In addition, keeping the bfq_queue scheduled for service, but with no
process reference any longer, may cause the bfq_queue to be freed when
descheduled from service. But this is assumed to never happen, and
causes a UAF if it happens. This, in turn, caused crashes [1, 2].
This commit fixes this issue by descheduling an empty bfq_queue when
it remains with not process reference.
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b00 ("CDC-NCM: handle incomplete transfer of MTU") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.
Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following race is observed due to which a processes faulting on a
swap entry, finds the page neither in swapcache nor swap. This causes
zram to give a zero filled page that gets mapped to the process,
resulting in a user space crash later.
Consider parent and child processes Pa and Pb sharing the same swap slot
with swap_count 2. Swap is on zram with SWP_SYNCHRONOUS_IO set.
Virtual address 'VA' of Pa and Pb points to the shared swap entry.
Pa Pb
fault on VA fault on VA
do_swap_page do_swap_page
lookup_swap_cache fails lookup_swap_cache fails
Pb scheduled out
swapin_readahead (deletes zram entry)
swap_free (makes swap_count 1)
Pb scheduled in
swap_readpage (swap_count == 1)
Takes SWP_SYNCHRONOUS_IO path
zram enrty absent
zram gives a zero filled page
Fix this by making sure that swap slot is freed only when swap count
drops down to one.
Link: http://lkml.kernel.org/r/1571743294-14285-1-git-send-email-vinmenon@codeaurora.org Fixes: aa8d22a11da9 ("mm: swap: SWP_SYNCHRONOUS_IO: skip swapcache only if swapped page has no other reference") Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org> Suggested-by: Minchan Kim <minchan@google.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
try_offline_node() is pretty much broken right now:
- The node span is updated when onlining memory, not when adding it. We
ignore memory that was mever onlined. Bad.
- We touch possible garbage memmaps. The pfn_to_nid(pfn) can easily
trigger a kernel panic. Bad for memory that is offline but also bad
for subsection hotadd with ZONE_DEVICE, whereby the memmap of the
first PFN of a section might contain garbage.
- Sections belonging to mixed nodes are not properly considered.
As memory blocks might belong to multiple nodes, we would have to walk
all pageblocks (or at least subsections) within present sections.
However, we don't have a way to identify whether a memmap that is not
online was initialized (relevant for ZONE_DEVICE). This makes things
more complicated.
Luckily, we can piggy pack on the node span and the nid stored in memory
blocks. Currently, the node span is grown when calling
move_pfn_range_to_zone() - e.g., when onlining memory, and shrunk when
removing memory, before calling try_offline_node(). Sysfs links are
created via link_mem_sections(), e.g., during boot or when adding
memory.
If the node still spans memory or if any memory block belongs to the
nid, we don't set the node offline. As memory blocks that span multiple
nodes cannot get offlined, the nid stored in memory blocks is reliable
enough (for such online memory blocks, the node still spans the memory).
Introduce for_each_memory_block() to efficiently walk all memory blocks.
Note: We will soon stop shrinking the ZONE_DEVICE zone and the node span
when removing ZONE_DEVICE memory to fix similar issues (access of
garbage memmaps) - until we have a reliable way to identify whether
these memmaps were properly initialized. This implies later, that once
a node had ZONE_DEVICE memory, we won't be able to set a node offline -
which should be acceptable.
Since commit f1dd2cd13c4b ("mm, memory_hotplug: do not associate
hotadded memory to zones until online") memory that is added is not
assoziated with a zone/node (memmap not initialized). The introducing
commit 60a5a19e7419 ("memory-hotplug: remove sysfs file of node")
already missed that we could have multiple nodes for a section and that
the zone/node span is updated when onlining pages, not when adding them.
I tested this by hotplugging two DIMMs to a memory-less and cpu-less
NUMA node. The node is properly onlined when adding the DIMMs. When
removing the DIMMs, the node is properly offlined.
Commit 1b7e816fc80e ("mm: slub: Fix slab walking for init_on_free")
fixed one problem with the slab walking but missed a key detail: When
walking the list, the head and tail pointers need to be updated since we
end up reversing the list as a result. Without doing this, bulk free is
broken.
One way this is exposed is a NULL pointer with slub_debug=F:
=============================================================================
BUG skbuff_head_cache (Tainted: G T): Object already free
-----------------------------------------------------------------------------
An exiting task might belong to an offline cgroup. In this case an
attempt to grab a cgroup reference from the task can end up with an
infinite loop in hugetlb_cgroup_charge_cgroup(), because neither the
cgroup will become online, neither the task will be migrated to a live
cgroup.
Fix this by switching over to css_tryget(). As css_tryget_online()
can't guarantee that the cgroup won't go offline, in most cases the
check doesn't make sense. In this particular case users of
hugetlb_cgroup_charge_cgroup() are not affected by this change.
A similar problem is described by commit 18fa84a2db0e ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Link: http://lkml.kernel.org/r/20191106225131.3543616-2-guro@fb.com Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Tejun Heo <tj@kernel.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've encountered a rcu stall in get_mem_cgroup_from_mm():
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 33-....: (21000 ticks this GP) idle=6c6/1/0x4000000000000002 softirq=35441/35441 fqs=5017
(t=21031 jiffies g=324821 q=95837) NMI backtrace for cpu 33
<...>
RIP: 0010:get_mem_cgroup_from_mm+0x2f/0x90
<...>
__memcg_kmem_charge+0x55/0x140
__alloc_pages_nodemask+0x267/0x320
pipe_write+0x1ad/0x400
new_sync_write+0x127/0x1c0
__kernel_write+0x4f/0xf0
dump_emit+0x91/0xc0
writenote+0xa0/0xc0
elf_core_dump+0x11af/0x1430
do_coredump+0xc65/0xee0
get_signal+0x132/0x7c0
do_signal+0x36/0x640
exit_to_usermode_loop+0x61/0xd0
do_syscall_64+0xd4/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
The problem is caused by an exiting task which is associated with an
offline memcg. We're iterating over and over in the do {} while
(!css_tryget_online()) loop, but obviously the memcg won't become online
and the exiting task won't be migrated to a live memcg.
Let's fix it by switching from css_tryget_online() to css_tryget().
As css_tryget_online() cannot guarantee that the memcg won't go offline,
the check is usually useless, except some rare cases when for example it
determines if something should be presented to a user.
A similar problem is described by commit 18fa84a2db0e ("cgroup: Use
css_tryget() instead of css_tryget_online() in task_get_css()").
Johannes:
: The bug aside, it doesn't matter whether the cgroup is online for the
: callers. It used to matter when offlining needed to evacuate all charges
: from the memcg, and so needed to prevent new ones from showing up, but we
: don't care now.
Link: http://lkml.kernel.org/r/20191106225131.3543616-1-guro@fb.com Signed-off-by: Roman Gushchin <guro@fb.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Tejun Heo <tj@kernel.org> Reviewed-by: Shakeel Butt <shakeeb@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Michal Koutn <mkoutny@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d883544515aa ("mm: mempolicy: make the behavior consistent when
MPOL_MF_MOVE* and MPOL_MF_STRICT were specified") fixed the return value
of mbind() for a couple of corner cases. But, it altered the errno for
some other cases, for example, mbind() should return -EFAULT when part
or all of the memory range specified by nodemask and maxnode points
outside your accessible address space, or there was an unmapped hole in
the specified memory range specified by addr and len.
Fix this by preserving the errno returned by queue_pages_range(). And,
the pagelist may be not empty even though queue_pages_range() returns
error, put the pages back to LRU since mbind_range() is not called to
really apply the policy so those pages should not be migrated, this is
also the old behavior before the problematic commit.
Link: http://lkml.kernel.org/r/1572454731-3925-1-git-send-email-yang.shi@linux.alibaba.com Fixes: d883544515aa ("mm: mempolicy: make the behavior consistent when MPOL_MF_MOVE* and MPOL_MF_STRICT were specified") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Reported-by: Li Xinhai <lixinhai.lxh@gmail.com> Reviewed-by: Li Xinhai <lixinhai.lxh@gmail.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Michal Hocko <mhocko@suse.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> [4.19 and 5.2+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For both PASID-based-Device-TLB Invalidate Descriptor and
Device-TLB Invalidate Descriptor, the Physical Function Source-ID
value is split according to this layout:
PFSID[3:0] is set at offset 12 and PFSID[15:4] is put at offset 52.
Fix the part laid out at offset 52.
Fixes: 0f725561e1684 ("iommu/vt-d: Add definitions for PFSID") Signed-off-by: Eric Auger <eric.auger@redhat.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: stable@vger.kernel.org # v4.19+ Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i") Cc: <stable@vger.kernel.org> # v4.15+ Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A cast to 'time_t' was accidentally left in place during the
conversion of __do_adjtimex() to 64-bit timestamps, so the
resulting value is incorrectly truncated.
Remove the cast so the 64-bit time gets propagated correctly.
These extra EHL entries won't behave as expected without a bit more work
on the kernel side so let's drop them until that kernel work has had a
chance to land. Userspace trying to use these new entries won't get the
advantage of the new functionality these entries are meant to provide,
but at least it won't misbehave.
When we do add these back in the future, we'll probably want to
explicitly use separate tables for ICL and EHL so that userspace
software that mistakenly uses these entries (which are undefined on ICL)
sees the same behavior it sees with all the other undefined entries.
Cc: Francisco Jerez <francisco.jerez.plata@intel.com> Cc: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Lucas De Marchi <lucas.demarchi@intel.com> Cc: <stable@vger.kernel.org> # v5.3+ Fixes: f4071997f1de ("drm/i915/ehl: Update MOCS table for EHL") Signed-off-by: Matt Roper <matthew.d.roper@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191112224757.25116-1-matthew.d.roper@intel.com Reviewed-by: Francisco Jerez <currojerez@riseup.net>
(cherry picked from commit 046091758b50a5fff79726a31c1391614a3d84c8) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since CNP it's possible for rawclk to have two different values, 19.2
and 24 MHz. If the value indicated by SFUSE_STRAP register is different
from the power on default for PCH_RAWCLK_FREQ, we'll end up having a
mismatch between the rawclk hardware and software states after
suspend/resume. On previous platforms this used to work by accident,
because the power on defaults worked just fine.
Update the rawclk also on resume. The natural place to do this would be
intel_modeset_init_hw(), however VLV/CHV need it done before
intel_power_domains_init_hw(). Thus put it there even if it feels
slightly out of place.
v2: Call intel_update_rawclck() in intel_power_domains_init_hw() for all
platforms (Ville).
Reported-by: Shawn Lee <shawn.c.lee@intel.com> Cc: Shawn Lee <shawn.c.lee@intel.com> Cc: Ville Syrjala <ville.syrjala@linux.intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Shawn Lee <shawn.c.lee@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191101142024.13877-1-jani.nikula@intel.com
(cherry picked from commit 59ed05ccdded5eb18ce012eff3d01798ac8535fa) Cc: <stable@vger.kernel.org> # v4.15+ Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A test case was reported where two linked reads with registered buffers
failed the second link always. This is because we set the expected value
of a request in req->result, and if we don't get this result, then we
fail the dependent links. For some reason the registered buffer import
returned -ERROR/0, while the normal import returns -ERROR/length. This
broke linked commands with registered buffers.
Fix this by making io_import_fixed() correctly return the mapped length.
We need to get the underlying dentry of parent; sure, absent the races
it is the parent of underlying dentry, but there's nothing to prevent
losing a timeslice to preemtion in the middle of evaluation of
lower_dentry->d_parent->d_inode, having another process move lower_dentry
around and have its (ex)parent not pinned anymore and freed on memory
pressure. Then we regain CPU and try to fetch ->d_inode from memory
that is freed by that point.
dentry->d_parent *is* stable here - it's an argument of ->lookup() and
we are guaranteed that it won't be moved anywhere until we feed it
to d_add/d_splice_alias. So we safely go that way to get to its
underlying dentry.
Cc: stable@vger.kernel.org # since 2009 or so Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lower_dentry can't go from positive to negative (we have it pinned),
but it *can* go from negative to positive. So fetching ->d_inode
into a local variable, doing a blocking allocation, checking that
now ->d_inode is non-NULL and feeding the value we'd fetched
earlier to a function that won't accept NULL is not a good idea.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Coffee Lake platforms have a skewed HPET timer once the SoCs entered
PC10, which in consequence marks TSC as unstable because HPET is used as
watchdog clocksource for TSC.
Harry Pan tried to work around it in the clocksource watchdog code [1]
thereby creating a circular dependency between HPET and TSC. This also
ignores the fact, that HPET is not only unsuitable as watchdog clocksource
on these systems, it becomes unusable in general.
Many cheap devices use Silead touchscreen controllers. Testing has shown
repeatedly that these touchscreen controllers work fine at 400KHz, but for
unknown reasons do not work properly at 100KHz. This has been seen on
both ARM and x86 devices using totally different i2c controllers.
On some devices the ACPI tables list another device at the same I2C-bus
as only being capable of 100KHz, testing has shown that these other
devices work fine at 400KHz (as can be expected of any recent I2C hw).
This commit makes i2c_acpi_find_bus_speed() always return 400KHz if a
Silead touchscreen controller is present, fixing the touchscreen not
working on devices which ACPI tables' wrongly list another device on the
same bus as only being capable of 100KHz.
Specifically this fixes the touchscreen on the Jumper EZpad 6 m4 not
working.
Reported-by: youling 257 <youling257@gmail.com> Tested-by: youling 257 <youling257@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: rewording warning a little] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an hfi1 card is inserted in a Gen4 systems, the driver will avoid the
gen3 speed bump and the card will operate at half speed.
This is because the driver avoids the gen3 speed bump when the parent bus
speed isn't identical to gen3, 8.0GT/s. This is not compatible with gen4
and newer speeds.
Fix by relaxing the test to explicitly look for the lower capability
speeds which inherently allows for gen4 and all future speeds.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20191101192059.106248.1699.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Reviewed-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: James Erwin <james.erwin@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normal RDMA WRITE request never returns IB_WC_RNR_RETRY_EXC_ERR to ULPs
because it does not need post receive buffer on the responder side.
Consequently, as an enhancement to normal RDMA WRITE request inside the
hfi1 driver, TID RDMA WRITE request should not return such an error status
to ULPs, although it does receive RNR NAKs from the responder when TID
resources are not available. This behavior is violated when
qp->s_rnr_retry_cnt is set in current hfi1 implementation.
This patch enforces these semantics by avoiding any reaction to the updates
of the RNR QP attributes.
Fixes: 3c6cb20a0d17 ("IB/hfi1: Add TID RDMA WRITE functionality into RDMA verbs") Link: https://lore.kernel.org/r/20191025195842.106825.71532.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a TID RDMA WRITE request, a QP on the responder side could be put into
a queue when a hardware flow is not available. A RNR NAK will be returned
to the requester with a RNR timeout value based on the position of the QP
in the queue. The tid_rdma_flow_wt variable is used to calculate the
timeout value and is determined by using a MTU of 4096 at the module
loading time. This could reduce the timeout value by half from the desired
value, leading to excessive RNR retries.
This patch fixes the issue by calculating the flow weight with the real
MTU assigned to the QP.
Fixes: 07b923701e38 ("IB/hfi1: Add functions to receive TID RDMA WRITE request") Link: https://lore.kernel.org/r/20191025195836.106825.77769.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The index r_tid_ack is used to indicate the next TID RDMA WRITE request to
acknowledge in the ring s_ack_queue[] on the responder side and should be
set to a valid index other than its initial value before r_tid_tail is
advanced to the next TID RDMA WRITE request and particularly before a TID
RDMA ACK is built. Otherwise, a NULL pointer dereference may result:
This problem can happen if a RESYNC request is received before r_tid_ack
is modified.
This patch fixes the issue by making sure that r_tid_ack is set to a valid
value before a TID RDMA ACK is built. Functions are defined to simplify
the code.
Fixes: 07b923701e38 ("IB/hfi1: Add functions to receive TID RDMA WRITE request") Fixes: 7cf0ad679de4 ("IB/hfi1: Add a function to receive TID RDMA RESYNC packet") Link: https://lore.kernel.org/r/20191025195830.106825.44022.stgit@awfm-01.aw.intel.com Cc: <stable@vger.kernel.org> Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly exempt ZONE_DEVICE pages from kvm_is_reserved_pfn() and
instead manually handle ZONE_DEVICE on a case-by-case basis. For things
like page refcounts, KVM needs to treat ZONE_DEVICE pages like normal
pages, e.g. put pages grabbed via gup(). But for flows such as setting
A/D bits or shifting refcounts for transparent huge pages, KVM needs to
to avoid processing ZONE_DEVICE pages as the flows in question lack the
underlying machinery for proper handling of ZONE_DEVICE pages.
This fixes a hang reported by Adam Borowski[*] in dev_pagemap_cleanup()
when running a KVM guest backed with /dev/dax memory, as KVM straight up
doesn't put any references to ZONE_DEVICE pages acquired by gup().
Note, Dan Williams proposed an alternative solution of doing put_page()
on ZONE_DEVICE pages immediately after gup() in order to simplify the
auditing needed to ensure is_zone_device_page() is called if and only if
the backing device is pinned (via gup()). But that approach would break
kvm_vcpu_{un}map() as KVM requires the page to be pinned from map() 'til
unmap() when accessing guest memory, unlike KVM's secondary MMU, which
coordinates with mmu_notifier invalidations to avoid creating stale
page references, i.e. doesn't rely on pages being pinned.
Reported-by: Adam Borowski <kilobyte@angband.pl> Analyzed-by: David Hildenbrand <david@redhat.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Cc: stable@vger.kernel.org Fixes: 3565fce3a659 ("mm, x86: get_user_pages() for dax mappings") Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Currently, rmi_f11_attention() and rmi_f12_attention() functions update
the attn_data data pointer and size based on the size of the expected
size of the attention data. However, if the actual valid data in the
attn buffer is less then the expected value then the updated data
pointer will point to memory beyond the end of the attn buffer. Using
the calculated valid_bytes instead will prevent this from happening.
This patch fixes an issue seen on HID touchpads which report finger
positions using RMI4 Function 12. The issue manifests itself as
spurious button presses as described in:
https://www.spinics.net/lists/linux-input/msg58618.html
Commit 24d28e4f1271 ("Input: synaptics-rmi4 - convert irq distribution
to irq_domain") switched the RMI4 driver to using an irq_domain to handle
RMI4 function interrupts. Functions with more then one interrupt now have
each interrupt mapped to their own IRQ and IRQ handler. The result of
this change is that the F12 IRQ handler was now getting called twice. Once
for the absolute data interrupt and once for the relative data interrupt.
For HID devices, calling rmi_f12_attention() a second time causes the
attn_data data pointer and size to be set incorrectly. When the touchpad
button is pressed, F30 will generate an interrupt and attempt to read the
F30 data from the invalid attn_data data pointer and report incorrect
button events.
This patch disables the F12 relative interrupt which prevents
rmi_f12_attention() from being called twice.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com> Reported-by: Simon Wood <simon@mungewell.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191025002527.3189-2-aduggan@synaptics.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The video buffer used by the queue is a vb2_v4l2_buffer, not a plain
vb2_buffer. Using the wrong type causes the allocation of the buffer
storage to be too small, causing a out of bounds write when
__init_vb2_v4l2_buffer initializes the buffer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Fixes: 3a762dbd5347 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20191104114454.10500-1-l.stach@pengutronix.de Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ptrace_stop() does preempt_enable_no_resched() to avoid the preemption,
but after that cgroup_enter_frozen() does spin_lock/unlock and this adds
another preemption point.
During rename exchange we might have successfully log the new name in the
source root's log tree, in which case we leave our log context (allocated
on stack) in the root's list of log contextes. However we might fail to
log the new name in the destination root, in which case we fallback to
a transaction commit later and never sync the log of the source root,
which causes the source root log context to remain in the list of log
contextes. This later causes invalid memory accesses because the context
was allocated on stack and after rename exchange finishes the stack gets
reused and overwritten for other purposes.
The kernel's linked list corruption detector (CONFIG_DEBUG_LIST=y) can
detect this and report something like the following:
This started happening recently when running some test cases from fstests
like btrfs/004 for example, because support for rename exchange was added
last week to fsstress from fstests.
So fix this by deleting the log context for the source root from the list
if we have logged the new name in the source root.
Reported-by: Su Yue <Damenly_Su@gmx.com> Fixes: d4682ba03ef618 ("Btrfs: sync log after logging new name") CC: stable@vger.kernel.org # 4.19+ Tested-by: Su Yue <Damenly_Su@gmx.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recently introduced unit descriptor validation had some bug for
processing and extension units, it counts a bControlSize byte twice so
it expected a bigger size than it should have been. This seems
resulting in a probe error on a few devices.
Fix the calculation for proper checks of PU and EU.
The commit 60849562a5db ("ALSA: usb-audio: Fix possible NULL
dereference at create_yamaha_midi_quirk()") added NULL checks in
create_yamaha_midi_quirk(), but there was an overlook. The code
allows one of either injd or outjd is NULL, but the second if check
made returning -ENODEV if any of them is NULL. Fix it in a proper
form.
Fixes: 60849562a5db ("ALSA: usb-audio: Fix possible NULL dereference at create_yamaha_midi_quirk()") Reported-by: Pavel Machek <pavel@denx.de> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191113111259.24123-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While output urb's snd_complete_urb() is executing, calling
prepare_outbound_urb() may cause endpoint stopped before
prepare_outbound_urb() returns and result in next urb submitted
to stopped endpoint. usb-audio driver cannot re-use it afterwards as
the urb is still hold by usb stack.
This change checks EP_FLAG_RUNNING flag after prepare_outbound_urb() again
to let snd_complete_urb() know the endpoint already stopped and does not
submit next urb. Below kind of error will be fixed:
[ 213.153103] usb 1-2: timeout: still 1 active urbs on EP #1
[ 213.164121] usb 1-2: cannot submit urb 0, error -16: unknown error
A check of the return value from get_cur_mix_raw() is missing at the
resolution test code in get_min_max_with_quirks(), which may leave the
variable untouched, leading to a random uninitialized value, as
detected by syzkaller fuzzer.
Add the missing return error check for fixing that.
If an SMC socket is immediately terminated after a non-blocking connect()
has been called, a memory leak is possible.
Due to the sock_hold move in
commit 301428ea3708 ("net/smc: fix refcounting for non-blocking connect()")
an extra sock_put() is needed in smc_connect_work(), if the internal
TCP socket is aborted and cancels the sk_stream_wait_connect() of the
connect worker.
Reported-by: syzbot+4b73ad6fc767e576e275@syzkaller.appspotmail.com Fixes: 301428ea3708 ("net/smc: fix refcounting for non-blocking connect()") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When setting the dump's time-stamp, use ktime_get_real in addition to
jiffies. This simplifies the user space implementation and bypasses
some inconsistent behavior with translating jiffies to current time.
The time taken is transformed into nsec, to comply with y2038 issue.
Fixes: c8e1da0bf923 ("devlink: Add health report functionality") Signed-off-by: Aya Levin <ayal@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a55 ("dpaa2-eth: defer probe on object allocate") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes '\n' from trace event class tcp_event_sk_skb to avoid
redundant new blank line and make output compact.
Fixes: af4325ecc24f ("tcp: expose sk_state in tcp_retransmit_skb tracepoint") Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Yafang Shao <laoar.shao@gmail.com> Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver/net/can/slcan.c is derived from slip.c. Memory leak was detected
by Syzkaller in slcan. Same issue exists in slip.c and this patch is
addressing the leak in slip.c.
Here is the slcan memory leak trace reported by Syzkaller:
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FASTOPEN does not work with SMC-sockets. Since SMC allows fallback to
TCP native during connection start, the FASTOPEN setsockopts trigger
this fallback, if the SMC-socket is still in state SMC_INIT.
But if a FASTOPEN setsockopt is called after a non-blocking connect(),
this is broken, and fallback does not make sense.
This change complements
commit cd2063604ea6 ("net/smc: avoid fallback in case of non-blocking connect")
and fixes the syzbot reported problem "WARNING in smc_unhash_sk".
Reported-by: syzbot+8488cc4cf1c9e09b8b86@syzkaller.appspotmail.com Fixes: e1bbdd570474 ("net/smc: reduce sock_put() for fallback sockets") Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In route.c, inet_rtm_getroute_build_skb() creates an skb with no
headroom. This skb is then used by inet_rtm_getroute() which may pass
it to rt_fill_info() and, from there, to ipmr_get_route(). The later
might try to reuse this skb by cloning it and prepending an IPv4
header. But since the original skb has no headroom, skb_push() triggers
skb_under_panic():
Actually the original skb used to have enough headroom, but the
reserve_skb() call was lost with the introduction of
inet_rtm_getroute_build_skb() by commit 404eb77ea766 ("ipv4: support
sport, dport and ip_proto in RTM_GETROUTE").
We could reserve some headroom again in inet_rtm_getroute_build_skb(),
but this function shouldn't be responsible for handling the special
case of ipmr_get_route(). Let's handle that directly in
ipmr_get_route() by calling skb_realloc_headroom() instead of
skb_clone().
Fixes: 404eb77ea766 ("ipv4: support sport, dport and ip_proto in RTM_GETROUTE") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com> Fixes: 2d8dc5bbf4e7 ("devlink: Add support for reload") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a malicious device gives a short MAC it can elicit up to
5 bytes of leaked memory out of the driver. We need to check for
ETH_ALEN instead.
Reported-by: syzbot+a8d4acdad35e6bbca308@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In scsi_mq_setup_tags(), cmd_size is calculated based on zero size for the
scatter-gather list in case the low level driver uses SG_NONE in its host
template.
cmd_size is passed on to the block layer for calculation of the request
size, and we've seen NULL pointer dereference errors from the block layer
in drivers where SG_NONE is used and a mq IO scheduler is active,
apparently as a consequence of this (see commit 68ab2d76e4be ("scsi:
cxlflash: Set sg_tablesize to 1 instead of SG_NONE"), and a recent patch by
Finn Thain converting the three m68k NFR5380 drivers to avoid setting
SG_NONE).
Try to avoid these errors by accounting for at least one sg list entry when
calculating cmd_size, regardless of whether the low level driver set a zero
sg_tablesize.
Tested on 030 m68k with the atari_scsi driver - setting sg_tablesize to
SG_NONE no longer results in a crash when loading this driver.
The page table pages corresponding to broken down large pages are zapped in
FIFO order, so that the large page can potentially be recovered, if it is
not longer being used for execution. This removes the performance penalty
for walking deeper EPT page tables.
By default, one large page will last about one hour once the guest
reaches a steady state.
Signed-off-by: Junaid Shahid <junaids@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a function to create a kernel thread associated with a given VM. In
particular, it ensures that the worker thread inherits the priority and
cgroups of the calling thread.
Signed-off-by: Junaid Shahid <junaids@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With some Intel processors, putting the same virtual address in the TLB
as both a 4 KiB and 2 MiB page can confuse the instruction fetch unit
and cause the processor to issue a machine check resulting in a CPU lockup.
Unfortunately when EPT page tables use huge pages, it is possible for a
malicious guest to cause this situation.
Add a knob to mark huge pages as non-executable. When the nx_huge_pages
parameter is enabled (and we are using EPT), all huge pages are marked as
NX. If the guest attempts to execute in one of those pages, the page is
broken down into 4K pages, which are then marked executable.
This is not an issue for shadow paging (except nested EPT), because then
the host is in control of TLB flushes and the problematic situation cannot
happen. With nested EPT, again the nested guest can cause problems shadow
and direct EPT is treated in the same way.
[ tglx: Fixup default to auto and massage wording a bit ]
Originally-by: Junaid Shahid <junaids@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The largepages debugfs entry is incremented/decremented as shadow
pages are created or destroyed. Clearing it will result in an
underflow, which is harmless to KVM but ugly (and could be
misinterpreted by tools that use debugfs information), so make
this particular statistic read-only.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: kvm-ppc@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A kernel module may need to check the value of the "mitigations=" kernel
command line parameter as part of its setup when the module needs
to perform software mitigations for a CPU flaw.
Uninline and export the helper functions surrounding the cpu_mitigations
enum to allow for their usage from a module.
Lastly, privatize the enum and cpu_mitigations variable since the value of
cpu_mitigations can be checked with the exported helper functions.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some processors may incur a machine check error possibly resulting in an
unrecoverable CPU lockup when an instruction fetch encounters a TLB
multi-hit in the instruction TLB. This can occur when the page size is
changed along with either the physical address or cache type. The relevant
erratum can be found here:
There are other processors affected for which the erratum does not fully
disclose the impact.
This issue affects both bare-metal x86 page tables and EPT.
It can be mitigated by either eliminating the use of large pages or by
using careful TLB invalidations when changing the page size in the page
tables.
Just like Spectre, Meltdown, L1TF and MDS, a new bit has been allocated in
MSR_IA32_ARCH_CAPABILITIES (PSCHANGE_MC_NO) and will be set on CPUs which
are mitigated against this issue.
For new IBRS_ALL CPUs, the Enhanced IBRS check at the beginning of
cpu_bugs_smt_update() causes the function to return early, unintentionally
skipping the MDS and TAA logic.
This is not a problem for MDS, because there appears to be no overlap
between IBRS_ALL and MDS-affected CPUs. So the MDS mitigation would be
disabled and nothing would need to be done in this function anyway.
But for TAA, the TAA_MSG_SMT string will never get printed on Cascade
Lake and newer.
The check is superfluous anyway: when 'spectre_v2_enabled' is
SPECTRE_V2_IBRS_ENHANCED, 'spectre_v2_user' is always
SPECTRE_V2_USER_NONE, and so the 'spectre_v2_user' switch statement
handles it appropriately by doing nothing. So just remove the check.
There is a general consensus that TSX usage is not largely spread while
the history shows there is a non trivial space for side channel attacks
possible. Therefore the tsx is disabled by default even on platforms
that might have a safe implementation of TSX according to the current
knowledge. This is a fair trade off to make.
There are, however, workloads that really do benefit from using TSX and
updating to a newer kernel with TSX disabled might introduce a
noticeable regressions. This would be especially a problem for Linux
distributions which will provide TAA mitigations.
Introduce config options X86_INTEL_TSX_MODE_OFF, X86_INTEL_TSX_MODE_ON
and X86_INTEL_TSX_MODE_AUTO to control the TSX feature. The config
setting can be overridden by the tsx cmdline options.
Add the documenation for TSX Async Abort. Include the description of
the issue, how to check the mitigation state, control the mitigation,
guidance for system administrators.
[ bp: Add proper SPDX tags, touch ups by Josh and me. ]
Co-developed-by: Antonio Gomez Iglesias <antonio.gomez.iglesias@intel.com> Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com> Signed-off-by: Antonio Gomez Iglesias <antonio.gomez.iglesias@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Mark Gross <mgross@linux.intel.com> Reviewed-by: Tony Luck <tony.luck@intel.com> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platforms which are not affected by X86_BUG_TAA may want the TSX feature
enabled. Add "auto" option to the TSX cmdline parameter. When tsx=auto
disable TSX when X86_BUG_TAA is present, otherwise enable TSX.
More details on X86_BUG_TAA can be found here:
https://www.kernel.org/doc/html/latest/admin-guide/hw-vuln/tsx_async_abort.html
[ bp: Extend the arg buffer to accommodate "auto\0". ]
Export the IA32_ARCH_CAPABILITIES MSR bit MDS_NO=0 to guests on TSX
Async Abort(TAA) affected hosts that have TSX enabled and updated
microcode. This is required so that the guests don't complain,
"Vulnerable: Clear CPU buffers attempted, no microcode"
when the host has the updated microcode to clear CPU buffers.
Microcode update also adds support for MSR_IA32_TSX_CTRL which is
enumerated by the ARCH_CAP_TSX_CTRL bit in IA32_ARCH_CAPABILITIES MSR.
Guests can't do this check themselves when the ARCH_CAP_TSX_CTRL bit is
not exported to the guests.
In this case export MDS_NO=0 to the guests. When guests have
CPUID.MD_CLEAR=1, they deploy MDS mitigation which also mitigates TAA.
Add the sysfs reporting file for TSX Async Abort. It exposes the
vulnerability and the mitigation state similar to the existing files for
the other hardware vulnerabilities.
Sysfs file path is:
/sys/devices/system/cpu/vulnerabilities/tsx_async_abort
TSX Async Abort (TAA) is a side channel vulnerability to the internal
buffers in some Intel processors similar to Microachitectural Data
Sampling (MDS). In this case, certain loads may speculatively pass
invalid data to dependent operations when an asynchronous abort
condition is pending in a TSX transaction.
This includes loads with no fault or assist condition. Such loads may
speculatively expose stale data from the uarch data structures as in
MDS. Scope of exposure is within the same-thread and cross-thread. This
issue affects all current processors that support TSX, but do not have
ARCH_CAP_TAA_NO (bit 8) set in MSR_IA32_ARCH_CAPABILITIES.
On CPUs which have their IA32_ARCH_CAPABILITIES MSR bit MDS_NO=0,
CPUID.MD_CLEAR=1 and the MDS mitigation is clearing the CPU buffers
using VERW or L1D_FLUSH, there is no additional mitigation needed for
TAA. On affected CPUs with MDS_NO=1 this issue can be mitigated by
disabling the Transactional Synchronization Extensions (TSX) feature.
A new MSR IA32_TSX_CTRL in future and current processors after a
microcode update can be used to control the TSX feature. There are two
bits in that MSR:
* TSX_CTRL_RTM_DISABLE disables the TSX sub-feature Restricted
Transactional Memory (RTM).
* TSX_CTRL_CPUID_CLEAR clears the RTM enumeration in CPUID. The other
TSX sub-feature, Hardware Lock Elision (HLE), is unconditionally
disabled with updated microcode but still enumerated as present by
CPUID(EAX=7).EBX{bit4}.
The second mitigation approach is similar to MDS which is clearing the
affected CPU buffers on return to user space and when entering a guest.
Relevant microcode update is required for the mitigation to work. More
details on this approach can be found here:
The TSX feature can be controlled by the "tsx" command line parameter.
If it is force-enabled then "Clear CPU buffers" (MDS mitigation) is
deployed. The effective mitigation state can be read from sysfs.
Add a kernel cmdline parameter "tsx" to control the Transactional
Synchronization Extensions (TSX) feature. On CPUs that support TSX
control, use "tsx=on|off" to enable or disable TSX. Not specifying this
option is equivalent to "tsx=off". This is because on certain processors
TSX may be used as a part of a speculative side channel attack.
Carve out the TSX controlling functionality into a separate compilation
unit because TSX is a CPU feature while the TSX async abort control
machinery will go to cpu/bugs.c.
[ bp: - Massage, shorten and clear the arg buffer.
- Clarifications of the tsx= possible options - Josh.
- Expand on TSX_CTRL availability - Pawan. ]
Transactional Synchronization Extensions (TSX) may be used on certain
processors as part of a speculative side channel attack. A microcode
update for existing processors that are vulnerable to this attack will
add a new MSR - IA32_TSX_CTRL to allow the system administrator the
option to disable TSX as one of the possible mitigations.
The CPUs which get this new MSR after a microcode upgrade are the ones
which do not set MSR_IA32_ARCH_CAPABILITIES.MDS_NO (bit 5) because those
CPUs have CPUID.MD_CLEAR, i.e., the VERW implementation which clears all
CPU buffers takes care of the TAA case as well.
[ Note that future processors that are not vulnerable will also
support the IA32_TSX_CTRL MSR. ]
Add defines for the new IA32_TSX_CTRL MSR and its bits.
TSX has two sub-features:
1. Restricted Transactional Memory (RTM) is an explicitly-used feature
where new instructions begin and end TSX transactions.
2. Hardware Lock Elision (HLE) is implicitly used when certain kinds of
"old" style locks are used by software.
Bit 7 of the IA32_ARCH_CAPABILITIES indicates the presence of the
IA32_TSX_CTRL MSR.
There are two control bits in IA32_TSX_CTRL MSR:
Bit 0: When set, it disables the Restricted Transactional Memory (RTM)
sub-feature of TSX (will force all transactions to abort on the
XBEGIN instruction).
Bit 1: When set, it disables the enumeration of the RTM and HLE feature
(i.e. it will make CPUID(EAX=7).EBX{bit4} and
CPUID(EAX=7).EBX{bit11} read as 0).
The other TSX sub-feature, Hardware Lock Elision (HLE), is
unconditionally disabled by the new microcode but still enumerated
as present by CPUID(EAX=7).EBX{bit4}, unless disabled by
IA32_TSX_CTRL_MSR[1] - TSX_CTRL_CPUID_CLEAR.
When a jump_whitelist bitmap is reused, it needs to be cleared.
Currently this is done with memset() and the size calculation assumes
bitmaps are made of 32-bit words, not longs. So on 64-bit
architectures, only the first half of the bitmap is cleared.
If some whitelist bits are carried over between successive batches
submitted on the same context, this will presumably allow embedding
the rogue instructions that we're trying to reject.
Use bitmap_zero() instead, which gets the calculation right.
Fixes: f8c08d8faee5 ("drm/i915/cmdparser: Add support for backward jumps") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some circumstances the RC6 context can get corrupted. We can detect
this and take the required action, that is disable RC6 and runtime PM.
The HW recovers from the corrupted state after a system suspend/resume
cycle, so detect the recovery and re-enable RC6 and runtime PM.
v2: rebase (Mika)
v3:
- Move intel_suspend_gt_powersave() to the end of the GEM suspend
sequence.
- Add commit message.
v4:
- Rebased on intel_uncore_forcewake_put(i915->uncore, ...) API
change.
v5: rebased on gem/gt split (Mika)
Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
