The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f85e ("iio: adc: mxs-lradc: Add support for ADC driver") Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PROC_FS is disabled, the function declarations for some
procfs functions are hidden, but the definitions are still build,
as shown by this compiler warning:
net/atm/resources.c:403:7: error: no previous prototype for 'atm_dev_seq_start' [-Werror=missing-prototypes]
net/atm/resources.c:409:6: error: no previous prototype for 'atm_dev_seq_stop' [-Werror=missing-prototypes]
net/atm/resources.c:414:7: error: no previous prototype for 'atm_dev_seq_next' [-Werror=missing-prototypes]
Add another #ifdef to leave these out of the build.
Two functions are defined and used in pcm_oss.c but also optionally
used from io.c, with an optional prototype. If CONFIG_SND_PCM_OSS_PLUGINS
is disabled, this causes a warning as the functions are not static
and have no prototype:
sound/core/oss/pcm_oss.c:1235:19: error: no previous prototype for 'snd_pcm_oss_write3' [-Werror=missing-prototypes]
sound/core/oss/pcm_oss.c:1266:19: error: no previous prototype for 'snd_pcm_oss_read3' [-Werror=missing-prototypes]
Avoid this by making the prototypes unconditional.
gcc with W=1 and ! CONFIG_NF_NAT
net/netfilter/nf_conntrack_netlink.c:3463:32: error:
‘exp_nat_nla_policy’ defined but not used [-Werror=unused-const-variable=]
3463 | static const struct nla_policy exp_nat_nla_policy[CTA_EXPECT_NAT_MAX+1] = {
| ^~~~~~~~~~~~~~~~~~
net/netfilter/nf_conntrack_netlink.c:2979:33: error:
‘any_addr’ defined but not used [-Werror=unused-const-variable=]
2979 | static const union nf_inet_addr any_addr;
| ^~~~~~~~
These variables use is controlled by CONFIG_NF_NAT, so should their definitions.
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
If scsi_dispatch_cmd() failed, the SCSI command was not sent to the target,
scsi_queue_rq() would return BLK_STS_RESOURCE and the related request would
be requeued. The timeout of this request would not fire, no one would
increase iodone_cnt.
The above flow would result the iodone_cnt smaller than iorequest_cnt. So
decrease the iorequest_cnt if dispatch failed to workaround the issue.
Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Reported-by: Ming Lei <ming.lei@redhat.com> Closes: https://lore.kernel.org/r/ZF+zB+bB7iqe0wGd@ovpn-8-17.pek2.redhat.com Link: https://lore.kernel.org/r/20230515070156.1790181-3-haowenchao2@huawei.com Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Using a semaphore in the wait_event*() condition is no good idea.
It hits a kernel WARN_ON() at prepare_to_wait_event() like:
do not call blocking ops when !TASK_RUNNING; state=1 set at
prepare_to_wait_event+0x6d/0x690
For avoiding the potential deadlock, rewrite to an open-coded loop
instead. Unlike the loop in wait_event*(), this uses wait_woken()
after the condition check, hence the task state stays consistent.
Since dvb_frontend_detach() is not called in ttusb_dec_exit_dvb(),
which is called when the device is disconnected, dvb_frontend_free()
is not finally called.
This causes a memory leak just by repeatedly plugging and
unplugging the device.
Fix this issue by adding dvb_frontend_detach() to ttusb_dec_exit_dvb().
IRQ handler netup_spi_interrupt() takes spinlock spi->lock. The lock
is initialized in netup_spi_init(). However, irq handler is registered
before initializing the lock.
Spinlock dma->lock and i2c->lock suffer from the same problem.
Fix this by registering the irq at the end of probe.
In su3000_read_mac_address, if i2c_transfer fails to execute two
messages, array mac address will not be initialized. Without handling
such error, later in function dvb_usb_adapter_dvb_init, proposed_mac
is accessed before initialization.
Fix this error by returning a negative value if message execution fails.
In digitv_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach digitv_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In rtl28xxu_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach rtl28xxu_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In ce6230_i2c_master_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach ce6230_i2c_master_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In ec168_i2c_xfer, msg is controlled by user. When msg[i].buf is null
and msg[i].len is zero, former checks on msg[i].buf would be passed.
If accessing msg[i].buf[0] without sanity check, null pointer deref
would happen. We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In az6027_i2c_xfer, msg is controlled by user. When msg[i].buf is null,
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in
az6027_i2c_xfer()") fix the null-ptr-deref bug when msg[i].addr is 0x99.
However, null-ptr-deref also happens when msg[i].addr is 0xd0 and 0xc0.
We add check on msg[i].len to prevent null-ptr-deref.
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.
The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
When unwind instruction is 0xb2,the subsequent instructions
are uleb128 bytes.
For now,it uses only the first uleb128 byte in code.
For vsp increments of 0x204~0x400,use one uleb128 byte like below:
0xc06a00e4 <unwind_test_work>: 0x80b27fac
Compact model index: 0
0xb2 0x7f vsp = vsp + 1024
0xac pop {r4, r5, r6, r7, r8, r14}
For vsp increments larger than 0x400,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x01 vsp = vsp + 1032
0xac pop {r4, r5, r6, r7, r8, r14}
The unwind works well since the decoded uleb128 byte is also 0x81.
For vsp increments larger than 0x600,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x02 vsp = vsp + 1544
0xac pop {r4, r5, r6, r7, r8, r14}
In this case,the decoded uleb128 result is 0x101(vsp=0x204+(0x101<<2)).
While the uleb128 used in code is 0x81(vsp=0x204+(0x81<<2)).
The unwind aborts at this frame since it gets incorrect vsp.
To fix this,add uleb128 decode to cover all the above case.
Signed-off-by: Haibo Li <haibo.li@mediatek.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a user can make copy_from_user() fail, there is a potential for
UAF/DF due to a lack of locking around the allocation, use and freeing
of the data buffers.
This issue is not theoretical. I managed to author a POC for it:
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation") Signed-off-by: Andreas Svensson <andreas.svensson@axis.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzkaller got the following report:
BUG: KASAN: use-after-free in sk_setup_caps+0x621/0x690 net/core/sock.c:2018
Read of size 8 at addr ffff888027f82780 by task syz-executor276/3255
The function sk_setup_caps (called by ip6_sk_dst_store_flow->
ip6_dst_store) referenced already freed memory as this memory was
freed by parallel task in udpv6_sendmsg->ip6_sk_dst_lookup_flow->
sk_dst_check.
The reason for this race condition is: sk_setup_caps() keeps using
the dst after transferring the ownership to the dst cache.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch replaces the tp->mss_cache check in getting TCP_MAXSEG
with tp->rx_opt.user_mss check for CLOSE/LISTEN sock. Since
tp->mss_cache is initialized with TCP_MSS_DEFAULT, checking if
it's zero is probably a bug.
With this change, getting TCP_MAXSEG before connecting will return
default MSS normally, and return user_mss if user_mss is set.
The value is changed under lock_sock() and po->bind_lock, so we
need READ_ONCE() to access pkt_sk(sk)->num without these locks in
packet_bind_spkt(), packet_bind(), and sk_diag_fill().
Note that WRITE_ONCE() is already added by commit c7d2ef5dd4b0
("net/packet: annotate accesses to po->bind").
BUG: KCSAN: data-race in packet_bind / packet_do_bind
write (marked) to 0xffff88802ffd1cee of 2 bytes by task 7322 on cpu 0:
packet_do_bind+0x446/0x640 net/packet/af_packet.c:3236
packet_bind+0x99/0xe0 net/packet/af_packet.c:3321
__sys_bind+0x19b/0x1e0 net/socket.c:1803
__do_sys_bind net/socket.c:1814 [inline]
__se_sys_bind net/socket.c:1812 [inline]
__x64_sys_bind+0x40/0x50 net/socket.c:1812
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
read to 0xffff88802ffd1cee of 2 bytes by task 7318 on cpu 1:
packet_bind+0xbf/0xe0 net/packet/af_packet.c:3322
__sys_bind+0x19b/0x1e0 net/socket.c:1803
__do_sys_bind net/socket.c:1814 [inline]
__se_sys_bind net/socket.c:1812 [inline]
__x64_sys_bind+0x40/0x50 net/socket.c:1812
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
value changed: 0x0300 -> 0x0000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7318 Comm: syz-executor.4 Not tainted 6.3.0-13380-g7fddb5b5300c #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Fixes: 96ec6327144e ("packet: Diag core and basic socket info dumping") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230524232934.50950-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Online Amateur Radio Community (OARC) has recently been experimenting
with building a nationwide packet network in the UK.
As part of our experimentation, we have been testing out packet on 300bps HF,
and playing with net/rom. For HF packet at this baud rate you really need
to make sure that your MTU is relatively low; AX.25 suggests a PACLEN of 60,
and a net/rom PACLEN of 40 to go with that.
However the Linux net/rom support didn't work with a low PACLEN;
the mkiss module would truncate packets if you set the PACLEN below about 200 or so, e.g.:
This didn't make any sense to me (if the packets are smaller why would they
be truncated?) so I started investigating.
I looked at the packets using ethereal, and found that many were just huge
compared to what I would expect.
A simple net/rom connection request packet had the request and then a bunch
of what appeared to be random data following it:
</quote>
Simon provided a patch that I slightly revised:
Not only we must not use skb_tailroom(), we also do
not want to count NR_NETWORK_LEN twice.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Co-Developed-by: Simon Kapadia <szymon@kapadia.pl> Signed-off-by: Simon Kapadia <szymon@kapadia.pl> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Simon Kapadia <szymon@kapadia.pl> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230524141456.1045467-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"_start" is used in several arches and proably should be reserved
for ARCH usage. Using it in a driver for a private symbol can cause
a build error when it conflicts with ARCH usage of the same symbol.
Therefore rename pl330's "_start" to "pl330_start_thread" so that there
is no conflict and no build error.
drivers/dma/pl330.c:1053:13: error: '_start' redeclared as different kind of symbol
1053 | static bool _start(struct pl330_thread *thrd)
| ^~~~~~
In file included from ../include/linux/interrupt.h:21,
from ../drivers/dma/pl330.c:18:
arch/riscv/include/asm/sections.h:11:13: note: previous declaration of '_start' with type 'char[]'
11 | extern char _start[];
| ^~~~~~
Fixes: b7d861d93945 ("DMA: PL330: Merge PL330 driver into drivers/dma/") Fixes: ae43b3289186 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jaswinder Singh <jassisinghbrar@gmail.com> Cc: Boojin Kim <boojin.kim@samsung.com> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Vinod Koul <vkoul@kernel.org> Cc: dmaengine@vger.kernel.org Cc: linux-riscv@lists.infradead.org Link: https://lore.kernel.org/r/20230524045310.27923-1-rdunlap@infradead.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, channel open messages were always sent to monitors on the first
ioctl() call for unbound HCI sockets, even if the command and arguments
were completely invalid. This can leave an exploitable hole with the abuse
of invalid ioctl calls.
This commit hardens the ioctl processing logic by first checking if the
command is valid, and immediately returning with an ENOIOCTLCMD error code
if it is not. This ensures that ioctl calls with invalid commands are free
of side effects, and increases the difficulty of further exploitation by
forcing exploitation to find a way to pass a valid command first.
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Co-developed-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Dragos-Marian Panait <dragos.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bq27xxx_external_power_changed() gets called when the charger is plugged
in or out. Rather then immediately scheduling an update wait 0.5 seconds
for things to stabilize, so that e.g. the (dis)charge current is stable
when bq27xxx_battery_update() runs.
Fixes: 740b755a3b34 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit e335bb51cc15 ("x86/unwind: Ensure stack pointer is aligned")
tried to align the stack pointer in show_trace_log_lvl(), otherwise the
"stack < stack_info.end" check can't guarantee that the last read does
not go past the end of the stack.
However, we have the same problem with the initial value of the stack
pointer, it can also be unaligned. So without this patch this trivial
kernel module
In the pvcalls_new_active_socket() function, most error paths call
pvcalls_back_release_active(fedata->dev, fedata, map) which calls
sock_release() on "sock". The bug is that the caller also frees sock.
Fix this by making every error path in pvcalls_new_active_socket()
release the sock, and don't free it in the caller.
Before this patch bq27xxx_battery_teardown() was setting poll_interval = 0
to avoid bq27xxx_battery_update() requeuing the delayed_work item.
There are 2 problems with this:
1. If the driver is unbound through sysfs, rather then the module being
rmmod-ed, this changes poll_interval unexpectedly
2. This is racy, after it being set poll_interval could be changed
before bq27xxx_battery_update() checks it through
/sys/module/bq27xxx_battery/parameters/poll_interval
Fix this by added a removed attribute to struct bq27xxx_device_info and
using that instead of setting poll_interval to 0.
There also is another poll_interval related race on remove(), writing
/sys/module/bq27xxx_battery/parameters/poll_interval will requeue
the delayed_work item for all devices on the bq27xxx_battery_devices
list and the device being removed was only removed from that list
after cancelling the delayed_work item.
Fix this by moving the removal from the bq27xxx_battery_devices list
to before cancelling the delayed_work item.
Fixes: 8cfaaa811894 ("bq27x00_battery: Fix OOPS caused by unregistring bq27x00 driver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_request_threaded_irq() requested IRQs are only free-ed after
the driver's remove function has ran. So the IRQ could trigger and
call bq27xxx_battery_update() after bq27xxx_battery_teardown() has
already run.
Switch to explicitly free-ing the IRQ in bq27xxx_battery_i2c_remove()
to fix this.
Fixes: 8807feb91b76 ("power: bq27xxx_battery: Add interrupt handling support") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And there is no protection against these racing with each other,
fix this race condition by making all callers take di->lock:
- Rename bq27xxx_battery_update() to bq27xxx_battery_update_unlocked()
- Add new bq27xxx_battery_update() which takes di->lock and then calls
bq27xxx_battery_update_unlocked()
- Make stale cache check code in bq27xxx_battery_get_property(), which
already takes di->lock directly to check the jiffies, call
bq27xxx_battery_update_unlocked() instead of messing with
the delayed_work item
- Make bq27xxx_battery_update_unlocked() mod the delayed-work item
so that the next poll is delayed to poll_interval milliseconds after
the last update independent of the source of the update
Fixes: 740b755a3b34 ("bq27x00: Poll battery state") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a battery's status changes from charging to full then
the charging-blink-full-solid trigger tries to change
the LED from blinking to solid/on.
As is documented in include/linux/leds.h to deactivate blinking /
to make the LED solid a LED_OFF must be send:
"""
* Deactivate blinking again when the brightness is set to LED_OFF
* via the brightness_set() callback.
"""
led_set_brighness() calls with a brightness value other then 0 / LED_OFF
merely change the brightness of the LED in its on state while it is
blinking.
So power_supply_update_bat_leds() must first send a LED_OFF event
before the LED_FULL to disable blinking.
Fixes: 6501f728c56f ("power_supply: Add new LED trigger charging-blink-solid-full") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
optlen is fetched without checking whether there is more than one byte to parse.
It can lead to out-of-bounds access.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: c61a40432509 ("[IPV6]: Find option offset by type.") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with
TX timestamp.") added a call to skb_orphan_frags_rx() to fix leaks with
zerocopy skbs. But it ended up adding a leak of its own. When
skb_orphan_frags_rx() fails, the function just returns, leaking the skb
it just cloned. Free it before returning.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 50749f2dd685 ("tcp/udp: Fix memleaks of sk and zerocopy skbs with TX timestamp.") Signed-off-by: Pratyush Yadav <ptyadav@amazon.de> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230522153020.32422-1-ptyadav@amazon.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
these endpoints (and similarly for the radio-shark driver).
The problem was caused by the fact that the driver does not check
whether the endpoints it uses are actually present and have the
appropriate types. This can be fixed by adding a simple check of
the endpoints.
Many of the older USB drivers in the Linux USB stack were written
based simply on a vendor's device specification. They use the
endpoint information in the spec and assume these endpoints will
always be present, with the properties listed, in any device matching
the given vendor and product IDs.
While that may have been true back then, with spoofing and fuzzing it
is not true any more. More and more we are finding that those old
drivers need to perform at least a minimum of checking before they try
to use any endpoint other than ep0.
To make this checking as simple as possible, we now add a couple of
utility routines to the USB core. usb_check_bulk_endpoints() and
usb_check_int_endpoints() take an interface pointer together with a
list of endpoint addresses (numbers and directions). They check that
the interface's current alternate setting includes endpoints with
those addresses and that each of these endpoints has the right type:
bulk or interrupt, respectively.
Although we already have usb_find_common_endpoints() and related
routines meant for a similar purpose, they are not well suited for
this kind of checking. Those routines find endpoints of various
kinds, but only one (either the first or the last) of each kind, and
they don't verify that the endpoints' addresses agree with what the
caller expects.
In theory the new routines could be more general: They could take a
particular altsetting as their argument instead of always using the
interface's current altsetting. In practice I think this won't matter
too much; multiple altsettings tend to be used for transferring media
(audio or visual) over isochronous endpoints, not bulk or interrupt.
Drivers for such devices will generally require more sophisticated
checking than these simplistic routines provide.
Hardik Garg [Fri, 26 May 2023 23:21:36 +0000 (16:21 -0700)]
selftests/memfd: Fix unknown type name build failure
Partially backport v6.3 commit 11f75a01448f ("selftests/memfd: add tests
for MFD_NOEXEC_SEAL MFD_EXEC") to fix an unknown type name build error.
In some systems, the __u64 typedef is not present due to differences in
system headers, causing compilation errors like this one:
fuse_test.c:64:8: error: unknown type name '__u64'
64 | static __u64 mfd_assert_get_seals(int fd)
This header includes the __u64 typedef which increases the likelihood
of successful compilation on a wider variety of systems.
The INVLPG instruction is used to invalidate TLB entries for a
specified virtual address. When PCIDs are enabled, INVLPG is supposed
to invalidate TLB entries for the specified address for both the
current PCID *and* Global entries. (Note: Only kernel mappings set
Global=1.)
Unfortunately, some INVLPG implementations can leave Global
translations unflushed when PCIDs are enabled.
As a workaround, never enable PCIDs on affected processors.
I expect there to eventually be microcode mitigations to replace this
software workaround. However, the exact version numbers where that
will happen are not known today. Once the version numbers are set in
stone, the processor list can be tweaked to only disable PCIDs on
affected processors with affected microcode.
Note: if anyone wants a quick fix that doesn't require patching, just
stick 'nopcid' on your kernel command-line.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ We hit the trace described in commit message with the
kselftest/nft_trans_stress.sh. This patch diverges from the upstream one
since kernel 4.14 does not have following symbols:
nft_chain_filter_init, nf_tables_flowtable_notifier ]
We must register nfnetlink ops last, as that exposes nf_tables to
userspace. Without this, we could theoretically get nfnetlink request
before net->nft state has been initialized.
Fixes: 99633ab29b213 ("netfilter: nf_tables: complete net namespace support") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[apanyaki: backport to v4.14-stable] Signed-off-by: Andrew Paniakin <apanyaki@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing lookups for sets on the same batch by using its ID, a set from a
different table can be used.
Then, when the table is removed, a reference to the set may be kept after
the set is freed, leading to a potential use-after-free.
When looking for sets by ID, use the table that was used for the lookup by
name, and only return sets belonging to that same table.
This fixes CVE-2022-2586, also reported as ZDI-CAN-17470.
Reported-by: Team Orca of Sea Security (@seasecresponse) Fixes: 958bee14d071 ("netfilter: nf_tables: use new transaction infrastructure to handle sets") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing lookups for rules on the same batch by using its ID, a rule from
a different chain can be used. If a rule is added to a chain but tries to
be positioned next to a rule from a different chain, it will be linked to
chain2, but the use counter on chain1 would be the one to be incremented.
When looking for rules by ID, use the chain that was used for the lookup by
name. The chain used in the context copied to the transaction needs to
match that same chain. That way, struct nft_rule does not need to get
enlarged with another member.
Fixes: 1a94e38d254b ("netfilter: nf_tables: add NFTA_RULE_ID attribute") Fixes: 75dd48e2e420 ("netfilter: nf_tables: Support RULE_ID reference in new rule") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Cc: <stable@vger.kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NFT_SET_EVAL is signalling the kernel that this sets can be updated from
the evaluation path, even if there are no expressions attached to the
element. Otherwise, set updates with no expressions fail. Update
description to describe the right semantics.
Fixes: 22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper function to parse the set element key netlink attribute.
v4: No changes
v3: New patch
[sbrivio: refactor error paths and labels; use NFT_DATA_VALUE_MAXLEN
instead of sizeof(*key) in helper, value can be longer than that;
rebase] Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 68030/020, an instruction such as, moveml %a2-%a3/%a5,%sp@- may cause
a stack page fault during instruction execution (i.e. not at an
instruction boundary) and produce a format 0xB exception frame.
In this situation, the value of USP will be unreliable. If a signal is
to be delivered following the exception, this USP value is used to
calculate the location for a signal frame. This can result in a
corrupted user stack.
The corruption was detected in dash (actually in glibc) where it showed
up as an intermittent "stack smashing detected" message and crash
following signal delivery for SIGCHLD.
It was hard to reproduce that failure because delivery of the signal
raced with the page fault and because the kernel places an unpredictable
gap of up to 7 bytes between the USP and the signal frame.
A format 0xB exception frame can be produced by a bus error or an
address error. The 68030 Users Manual says that address errors occur
immediately upon detection during instruction prefetch. The instruction
pipeline allows prefetch to overlap with other instructions, which means
an address error can arise during the execution of a different
instruction. So it seems likely that this patch may help in the address
error case also.
On CPM, the RISC core is a lot more efficiant when doing transfers
in 16-bits chunks than in 8-bits chunks, but unfortunately the
words need to be byte swapped as seen in a previous commit.
So, for large tranfers with an even size, allocate a temporary tx
buffer and byte-swap data before and after transfer.
This change allows setting higher speed for transfer. For instance
on an MPC 8xx (CPM1 comms RISC processor), the documentation tells
that transfer in byte mode at 1 kbit/s uses 0.200% of CPM load
at 25 MHz while a word transfer at the same speed uses 0.032%
of CPM load. This means the speed can be 6 times higher in
word mode for the same CPM load.
For the time being, only do it on CPM1 as there must be a
trade-off between the CPM load reduction and the CPU load required
to byte swap the data.
For different reasons, fsl-spi driver performs bits_per_word
modifications for different reasons:
- On CPU mode, to minimise amount of interrupts
- On CPM/QE mode to work around controller byte order
For CPU mode that's done in fsl_spi_prepare_message() while
for CPM mode that's done in fsl_spi_setup_transfer().
Reunify all of it in fsl_spi_prepare_message(), and catch
impossible cases early through master's bits_per_word_mask
instead of returning EINVAL later.
Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Proper use counter updates when activating and deactivating the object,
otherwise, this hits bogus EBUSY error.
Fixes: cd5125d8f518 ("netfilter: nf_tables: split set destruction in deactivate and destroy phase") Reported-by: Laura Garcia <nevola@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). However, since
nilfs_evict_inode() uses nilfs_root for some cleanup operations, it may
cause use-after-free read if inodes are left in "garbage_list" and
released by nilfs_dispose_list() at the end of nilfs_detach_log_writer().
Fix this issue by modifying nilfs_evict_inode() to only clear inode
without additional metadata changes that use nilfs_root if the file system
is degraded to read-only or the writer is detached.
When the MClientSnap reqeust's op is not CEPH_SNAP_OP_SPLIT the
request may still contain a list of 'split_realms', and we need
to skip it anyway. Or it will be parsed as a corrupt snaptrace.
s390's struct statfs and struct statfs64 contain padding, which
field-by-field copying does not set. Initialize the respective structs
with zeros before filling them and copying them to userspace, like it's
already done for the compat versions of these structs.
get_line_out_pfx() may trigger an Oops by overflowing the static array
with more than 8 channels. This was reported for MacBookPro 12,1 with
Cirrus codec.
As a workaround, extend for the 9.1 channels and also fix the
potential Oops by unifying the code paths accessing the same array
with the proper size check.
With faulty usb-storage devices, read/write can timeout, in that case
the SCSI layer will abort and re-issue the command. USB storage has no
internal timeout, it relies on SCSI layer aborting commands via
.eh_abort_handler() for non those responsive devices.
After two consecutive timeouts of the same command, SCSI layer calls
.eh_device_reset_handler(), without calling .eh_abort_handler() first.
CPU: 0 PID: 29770 Comm: syz-executor.0 Not tainted 6.3.0-rc6-syzkaller-gc478e5b17829 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/30/2023
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In igb_hash_mc_addr() the expression:
"mc_addr[4] >> 8 - bit_shift", right shifting "mc_addr[4]"
shift by more than 7 bits always yields zero, so hash becomes not so different.
Add initialization with bit_shift = 1 and add a loop condition to ensure
bit_shift will be always in [1..8] range.
Fixes: 9d5c824399de ("igb: PCI-Express 82575 Gigabit Ethernet driver") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
cas_saturn_firmware_init() allocates some memory using vmalloc(). This
memory is freed in the .remove() function but not it the error handling
path of the probe.
Add the missing vfree() to avoid a memory leak, should an error occur.
Fixes: fcaa40669cd7 ("cassini: use request_firmware") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
When Universal DVB card is detaching, netup_unidvb_dma_fini()
uses del_timer() to stop dma->timeout timer. But when timer
handler netup_unidvb_dma_timeout() is running, del_timer()
could not stop it. As a result, the use-after-free bug could
happen. The process is shown below:
When client and server establish a connection through vsock,
the client send a request to the server to initiate the connection,
then start a timer to wait for the server's response. When the server's
RESPONSE message arrives, the timer also times out and exits. The
server's RESPONSE message is processed first, and the connection is
established. However, the client's timer also times out, the original
processing logic of the client is to directly set the state of this vsock
to CLOSE and return ETIMEDOUT. It will not notify the server when the port
is released, causing the server port remain.
when client's vsock_connect timeout，it should check sk state is
ESTABLISHED or not. if sk state is ESTABLISHED, it means the connection
is established, the client should not set the sk state to CLOSE
Note: I encountered this issue on kernel-4.18, which can be fixed by
this patch. Then I checked the latest code in the community
and found similar issue.
Fixes: d021c344051a ("VSOCK: Introduce VM Sockets") Signed-off-by: Zhuang Shengen <zhuangshengen@huawei.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
xfrm_state_find() uses `encap_family` of the current template with
the passed local and remote addresses to find a matching state.
If an optional tunnel or BEET mode template is skipped in a mixed-family
scenario, there could be a mismatch causing an out-of-bounds read as
the addresses were not replaced to match the family of the next template.
While there are theoretical use cases for optional templates in outbound
policies, the only practical one is to skip IPComp states in inbound
policies if uncompressed packets are received that are handled by an
implicitly created IPIP state instead.
System-wide TSC read could cause a drift in C0 percentage calculation.
Because if first TSC is read and then one by one mperf is read for all
cpus, this introduces drift between mperf reading of later CPUs and TSC
reading. To lower this drift read TSC per CPU and also just after mperf
read. This technique improves C0 percentage calculation in Mperf monitor.
Wired GIP devices present multiple interfaces with the same USB identification
other than the interface number. This adds constants for differentiating two of
them and uses them where appropriate
Older gcc versions get confused by comparing a u32 value to a negative
constant in a switch()/case block:
drivers/clk/tegra/clk-tegra20.c: In function 'tegra20_clk_measure_input_freq':
drivers/clk/tegra/clk-tegra20.c:581:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_12MHZ:
^~~~
drivers/clk/tegra/clk-tegra20.c:593:2: error: case label does not reduce to an integer constant
case OSC_CTRL_OSC_FREQ_26MHZ:
mcb-pci requests a fixed-size memory region to parse the chameleon
table, however, if the chameleon table is smaller that the allocated
region, it could overlap with the IP Cores' memory regions.
After parsing the chameleon table, drop/reallocate the memory region
with the actual chameleon table size.
When we unbind a serial port hardware specific 8250 driver, the generic
serial8250 driver takes over the port. After that we see an oops about 10
seconds later. This can produce the following at least on some TI SoCs:
Turns out that we may still have the serial port hardware specific driver
port->pm in use, and serial8250_pm() tries to call it after the port
specific driver is gone:
serial8250_pm [8250_base] from uart_change_pm+0x54/0x8c [serial_base]
uart_change_pm [serial_base] from uart_hangup+0x154/0x198 [serial_base]
uart_hangup [serial_base] from __tty_hangup.part.0+0x328/0x37c
__tty_hangup.part.0 from disassociate_ctty+0x154/0x20c
disassociate_ctty from do_exit+0x744/0xaac
do_exit from do_group_exit+0x40/0x8c
do_group_exit from __wake_up_parent+0x0/0x1c
Let's fix the issue by calling serial8250_set_defaults() in
serial8250_unregister_port(). This will set the port back to using
the serial8250 default functions, and sets the port->pm to point to
serial8250_pm.
Some devices will include battery status usages in the HID descriptor
but we won't see that battery data for one reason or another. For example,
AES sensors won't send battery data unless an AES pen is in proximity.
If a user does not have an AES pen but instead only interacts with the
AES touchscreen with their fingers then there is no need for us to create
a battery object. Similarly, if a family of peripherals shares the same
HID descriptor between wired-only and wireless-capable SKUs, users of the
former may never see a battery event and will not want a power_supply
object created.
When using gpio based chip select the cs value can go outside the range
0 – 3. The various MX51_ECSPI_* macros did not take this into consideration
resulting in possible corruption of the configuration.
For example for any cs value over 3 the SCLKPHA bits would not be set and
other values in the register possibly corrupted.
One way to fix this is to just mask the cs bits to 2 bits. This still
allows all 4 native chip selects to work as well as gpio chip selects
(which can use any of the 4 chip select configurations).
Now that USB HID++ devices can gather a serial number that matches the
one that would be gathered when connected through a Unifying receiver,
remove the last difference by dropping the product ID as devices
usually have different product IDs when connected through USB or
Unifying.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying before patch: 4067-e8-ce-cd-45
- USB before patch: c086-e8-ce-cd-45
- Unifying and USB after patch: e8-ce-cd-45
For devices that support the 0x0003 feature (Device Information) version 4,
set the serial based on the output of that feature, rather than relying
on the usbhid code setting the USB serial.
This should allow the serial when connected through USB to (nearly)
match the one when connected through a unifying receiver.
For example, on the serials on a G903 wired/wireless mouse:
- Unifying: 4067-e8-ce-cd-45
- USB before patch: 017C385C3837
- USB after patch: c086-e8-ce-cd-45
projects / thirdparty / kernel / stable.git / log
