According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com> Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[lizf: Backported to 3.4: s/SJA1000_IR/REG_IR/] Signed-off-by: Zefan Li <lizefan@huawei.com>
If md->signature == MAC_DRIVER_MAGIC and md->block_size == 1023, a single
512 byte sector would be read (secsize / 512). However the partition
structure would be located past the end of the buffer (secsize % 512).
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
Signed-off-by: Sachin Pandhare <sachinpandhare@gmail.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:
$ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4
This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4. For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:
A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored. The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".
These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.
(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
The CH345 USB MIDI chip has two output ports. However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.
It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port. So we can just ignore the device's
descriptors, and hardcode one output port.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
Proxy entries could have null pointer to net-device.
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com> Fixes: 84920c1420e2 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2") Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Do not update the read stamp after swapping out the reader page from the
write buffer. If the reader page is swapped out of the buffer before an
event is written to it, then the read_stamp may get an out of date
timestamp, as the page timestamp is updated on the first commit to that
page.
rb_get_reader_page() only returns a page if it has an event on it, otherwise
it will return NULL. At that point, check if the page being returned has
events and has not been read yet. Then at that point update the read_stamp
to match the time stamp of the reader page.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit fcb26ec5b18d ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.
Fixes: fcb26ec5b18d ("broadcom: move all PHY_ID's to header") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.
Fixes: 8229efdaef1e ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code") CC: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
We need to wait for the flying timers, since we
are going to free the mrtable right after it.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.
When a passive TCP is created, we eventually call tcp_md5_do_add()
with sk pointing to the child. It is not owner by the user yet (we
will add this socket into listener accept queue a bit later anyway)
But we do own the spinlock, so amend the lockdep annotation to avoid
following splat :
Fixes: a8afca0329988 ("tcp: md5: protects md5sig_info with RCU") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.
Fixes: 8a4eb5734e8d ("net: introduce rx_handler results and logic around that") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.
Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.
This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.
Fixes: eb2b9311fd00 ("mac80211: mesh path table implementation") Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.
Fixes: 6cb6a27c45ce ("net: Call netdev_features_change() from netdev_update_features()") CC: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
Fixes: ffb865b1e460 ("usb: musb: add ulpi access operations") Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
now sctp auth cannot work well when setting a hmacid manually, which
is caused by that we didn't use the network order for hmacid, so fix
it by adding the transformation in sctp_auth_ep_set_hmacs.
even we set hmacid with the network order in userspace, it still
can't work, because of this condition in sctp_auth_ep_set_hmacs():
if (id > SCTP_AUTH_HMAC_ID_MAX)
return -EOPNOTSUPP;
so this wasn't working before and thus it won't break compatibility.
Fixes: 65b07e5d0d09 ("[SCTP]: API updates to suport SCTP-AUTH extensions.") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Do not clobber the buffer space passed from `search_binary_handler' and
originally preloaded by `prepare_binprm' with the executable's file
header by overwriting it with its interpreter's file header. Instead
keep the buffer space intact and directly use the data structure locally
allocated for the interpreter's file header, fixing a bug introduced in
2.1.14 with loadable module support (linux-mips.org commit beb11695
[Import of Linux/MIPS 2.1.14], predating kernel.org repo's history).
Adjust the amount of data read from the interpreter's file accordingly.
This was not an issue before loadable module support, because back then
`load_elf_binary' was executed only once for a given ELF executable,
whether the function succeeded or failed.
With loadable module support supported and enabled, upon a failure of
`load_elf_binary' -- which may for example be caused by architecture
code rejecting an executable due to a missing hardware feature requested
in the file header -- a module load is attempted and then the function
reexecuted by `search_binary_handler'. With the executable's file
header replaced with its interpreter's file header the executable can
then be erroneously accepted in this subsequent attempt.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
Writing a number to /sys/bus/scsi/devices/<sdev>/queue_ramp_up_period
returns the value of that number instead of the number of bytes written.
This behavior can confuse programs expecting POSIX write() semantics.
Fix this by returning the number of bytes written instead.
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Arnaldo reported that tracepoint filters seem to misbehave (ie. not
apply) on inherited events.
The fix is obvious; filters are only set on the actual (parent)
event, use the normal pattern of using this parent event for filters.
This is safe because each child event has a reference to it.
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: David Ahern <dsahern@gmail.com> Cc: Frédéric Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Wang Nan <wangnan0@huawei.com> Link: http://lkml.kernel.org/r/20151102095051.GN17308@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If we are using the NO_HOLES feature, we have a tiny time window when
running delalloc for a nodatacow inode where we can race with a concurrent
link or xattr add operation leading to a BUG_ON.
This happens because at run_delalloc_nocow() we end up casting a leaf item
of type BTRFS_INODE_[REF|EXTREF]_KEY or of type BTRFS_XATTR_ITEM_KEY to a
file extent item (struct btrfs_file_extent_item) and then analyse its
extent type field, which won't match any of the expected extent types
(values BTRFS_FILE_EXTENT_[REG|PREALLOC|INLINE]) and therefore trigger an
explicit BUG_ON(1).
The following sequence diagram shows how the race happens when running a
no-cow dellaloc range [4K, 8K[ for inode 257 and we have the following
neighbour leafs:
(Note the implicit hole for inode 257 regarding the [0, 8K[ range)
CPU 1 CPU 2
run_dealloc_nocow()
btrfs_lookup_file_extent()
--> searches for a key with value
(257 EXTENT_DATA 4096) in the
fs/subvol tree
--> returns us a path with
path->nodes[0] == leaf X and
path->slots[0] == N
because path->slots[0] is >=
btrfs_header_nritems(leaf X), it
calls btrfs_next_leaf()
btrfs_next_leaf()
--> releases the path
hard link added to our inode,
with key (257 INODE_REF 500)
added to the end of leaf X,
so leaf X now has N + 1 keys
--> searches for the key
(257 INODE_REF 256), because
it was the last key in leaf X
before it released the path,
with path->keep_locks set to 1
--> ends up at leaf X again and
it verifies that the key
(257 INODE_REF 256) is no longer
the last key in the leaf, so it
returns with path->nodes[0] ==
leaf X and path->slots[0] == N,
pointing to the new item with
key (257 INODE_REF 500)
the loop iteration of run_dealloc_nocow()
does not break out the loop and continues
because the key referenced in the path
at path->nodes[0] and path->slots[0] is
for inode 257, its type is < BTRFS_EXTENT_DATA_KEY
and its offset (500) is less then our delalloc
range's end (8192)
the item pointed by the path, an inode reference item,
is (incorrectly) interpreted as a file extent item and
we get an invalid extent type, leading to the BUG_ON(1):
When we get loaded by a 64-bit bootloader, kernel entry point is
startup_64 in head_64.S. We don't trust any and all bootloaders because
some will fiddle with CPU configuration so we go ahead and massage each
CPU into sanity again.
For example, some dell BIOSes have this XD disable feature which set
IA32_MISC_ENABLE[34] and disable NX. This might be some dumb workaround
for other OSes but Linux sure doesn't need it.
A similar thing is present in the Surface 3 firmware - see
https://bugzilla.kernel.org/show_bug.cgi?id=106051 - which sets this bit
only on the BSP:
Reported by Clifford and Craig for JMicron OHCI-1394 + SDHCI combo
controllers: Often or even most of the time, the controller is
initialized with the message "added OHCI v1.10 device as card 0, 4 IR +
0 IT contexts, quirks 0x10". With 0 isochronous transmit DMA contexts
(IT contexts), applications like audio output are impossible.
However, OHCI-1394 demands that at least 4 IT contexts are implemented
by the link layer controller, and indeed JMicron JMB38x do implement
four of them. Only their IsoXmitIntMask register is unreliable at early
access.
With my own JMB381 single function controller I found:
- I can reproduce the problem with a lower probability than Craig's.
- If I put a loop around the section which clears and reads
IsoXmitIntMask, then either the first or the second attempt will
return the correct initial mask of 0x0000000f. I never encountered
a case of needing more than a second attempt.
- Consequently, if I put a dummy reg_read(...IsoXmitIntMaskSet)
before the first write, the subsequent read will return the correct
result.
- If I merely ignore a wrong read result and force the known real
result, later isochronous transmit DMA usage works just fine.
So let's just fix this chip bug up by the latter method. Tested with
JMB381 on kernel 3.13 and 4.3.
Since OHCI-1394 generally requires 4 IT contexts at a minium, this
workaround is simply applied whenever the initial read of IsoXmitIntMask
returns 0, regardless whether it's a JMicron chip or not. I never heard
of this issue together with any other chip though.
I am not 100% sure that this fix works on the OHCI-1394 part of JMB380
and JMB388 combo controllers exactly the same as on the JMB381 single-
function controller, but so far I haven't had a chance to let an owner
of a combo chip run a patched kernel.
Strangely enough, IsoRecvIntMask is always reported correctly, even
though it is probed right before IsoXmitIntMask.
Reported-by: Clifford Dunn Reported-by: Craig Moore <craig.moore@qenos.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
[lizf: Backported to 3.4: use dev_notice() instead of ohci_notice()] Signed-off-by: Zefan Li <lizefan@huawei.com>
HP ProBook 6550b needs the same pin fixup applied to other HP B-series
laptops with docks for making its headphone and dock headphone jacks
working properly. We just need to add the codec SSID to the list.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=191971 Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
That commit introduced a regression at least for the case of the SG_IO ioctl()
running without CAP_SYS_RAWIO capability (e.g., unprivileged users) when there
are no active paths: the ioctl() fails with the ENOTTY errno immediately rather
than blocking due to queue_if_no_path until a path becomes active, for example.
That case happens to be exercised by QEMU KVM guests with 'scsi-block' devices
(qemu "-device scsi-block" [1], libvirt "<disk type='block' device='lun'>" [2])
from multipath devices; which leads to SCSI/filesystem errors in such a guest.
More general scenarios can hit that regression too. The following demonstration
employs a SG_IO ioctl() with a standard SCSI INQUIRY command for this objective
(some output & user changes omitted for brevity and comments added for clarity).
Reverting that commit restores normal operation (queueing) in failing scenarios;
tested on linux-next (next-20151022).
1) Test-case is based on sg_simple0 [3] (just SG_IO; remove SG_GET_VERSION_NUM)
$ cat sg_simple0.c
... see [3] ...
$ sed '/SG_GET_VERSION_NUM/,/}/d' sg_simple0.c > sgio_inquiry.c
$ gcc sgio_inquiry.c -o sgio_inquiry
2) The ioctl() works fine with active paths present.
5) The ioctl() only works if the SYS_CAP_RAWIO capability is present
(then queueing happens -- in this example, queue_if_no_path is set);
this is due to a conditional check in scsi_verify_blk_ioctl().
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
We've had many reports that some Creative sound cards with CA0132
don't work well. Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used. All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.
This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries. I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.
Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too. So
the flag is applied to all Creative entries.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[lizf: Backported to 3.4: drop the change to macro AZX_DCAPS_PRESET_CTHDA] Signed-off-by: Zefan Li <lizefan@huawei.com>
Currently when the system is trying to uninstall the ACPI interrupt
handler, it uses acpi_gbl_FADT.sci_interrupt as the IRQ number.
However, the IRQ number that the ACPI interrupt handled is installed
for comes from acpi_gsi_to_irq() and that is the number that should
be used for the handler removal.
Fix this problem by using the mapped IRQ returned from acpi_gsi_to_irq()
as appropriate.
Acked-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Chen Yu <yu.c.chen@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
This adds the USB ID for the Sitecom WLA2100. The Windows 10 inf file
was checked to verify that the addition is correct.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Frans van de Wiel <fvdw@fvdw.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If a EXT4 filesystem utilizes JBD2 journaling and an error occurs, the
journaling will be aborted first and the error number will be recorded
into JBD2 superblock and, finally, the system will enter into the
panic state in "errors=panic" option. But, in the rare case, this
sequence is little twisted like the below figure and it will happen
that the system enters into panic state, which means the system reset
in mobile environment, before completion of recording an error in the
journal superblock. In this case, e2fsck cannot recognize that the
filesystem failure occurred in the previous run and the corruption
wouldn't be fixed.
The VT-d specification says that "Software must enable ATS on endpoint
devices behind a Root Port only if the Root Port is reported as
supporting ATS transactions."
We walk up the tree to find a Root Port, but for integrated devices we
don't find one — we get to the host bridge. In that case we *should*
allow ATS. Currently we don't, which means that we are incorrectly
failing to use ATS for the integrated graphics. Fix that.
We should never break out of this loop "naturally" with bus==NULL,
since we'll always find bridge==NULL in that case (and now return 1).
So remove the check for (!bridge) after the loop, since it can never
happen. If it did, it would be worthy of a BUG_ON(!bridge). But since
it'll oops anyway in that case, that'll do just as well.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[lizf: Backported to 3.4:
- adjust context
- drop the last part of the changes of the patch] Signed-off-by: Zefan Li <lizefan@huawei.com>
If we fail to allocate a partition structure in the middle of the partition
creation process, the already allocated partitions are never removed, which
means they are still present in the partition list and their resources are
never freed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
hid_connect adds various strings to the buffer but they're all
conditional. You can find circumstances where nothing would be written
to it but the kernel will still print the supposedly empty buffer with
printk. This leads to corruption on the console/in the logs.
Ensure buf is initialized to an empty string.
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>
[dvhart: Initialize string to "" rather than assign buf[0] = NULL;] Cc: Jiri Kosina <jikos@kernel.org> Cc: linux-input@vger.kernel.org Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Zefan Li <lizefan@huawei.com>
Handle a write being requested to the page immediately beyond the EOF
marker on a cache object. Currently this gets an assertion failure in
CacheFiles because the EOF marker is used there to encode information about
a partial page at the EOF - which could lead to an unknown blank spot in
the file if we extend the file over it.
The problem is actually in fscache where we check the index of the page
being written against store_limit. store_limit is set to the number of
pages that we're allowed to store by fscache_set_store_limit() - which
means it's one more than the index of the last page we're allowed to store.
The problem is that we permit writing to a page with an index _equal_ to
the store limit - when we should reject that case.
Whilst we're at it, change the triggered assertion in CacheFiles to just
return -ENOBUFS instead.
The assertion failure looks something like this:
CacheFiles: Assertion failed
1000 < 7b1 is false
------------[ cut here ]------------
kernel BUG at fs/cachefiles/rdwr.c:962!
...
RIP: 0010:[<ffffffffa02c9e83>] [<ffffffffa02c9e83>] cachefiles_write_page+0x273/0x2d0 [cachefiles]
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Only override netfs->primary_index when registering success.
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lizf: Backported to 3.4: there are no n_active and flags in primary_index] Signed-off-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
Only cpu seeing dst refcount going to 0 can safely
dereference dst->flags.
Otherwise an other cpu might already have freed the dst.
Fixes: 27b75c95f10d ("net: avoid RCU for NOCACHE dst") Reported-by: Greg Thelen <gthelen@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
When dropping a lock while iterating a list we must restart the search
as other threads could have manipulated the list under us. Without this
we can get stuck in an endless loop. This bug was introduced by
Thanks go to Dan Williams <dan.j.williams@intel.com> for tracking all this
prior history down.
Reported-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Fixes: bc3f02a795d3b4faa99d37390174be2a75d091bd Signed-off-by: James Bottomley <JBottomley@Odin.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Both tunnel6_protocol and tunnel46_protocol share the same error
handler, tunnel6_err(), which traverses through tunnel6_handlers list.
For ipip6 tunnels, we need to traverse tunnel46_handlers as we do e.g.
in tunnel46_rcv(). Current code can generate an ICMPv6 error message
with an IPv4 packet embedded in it.
Fixes: 73d605d1abbd ("[IPSEC]: changing API of xfrm6_tunnel_register") Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
In nop_mcount, shdr->sh_offset and welp->r_offset should handle
endianness properly, otherwise it will trigger Segmentation fault
if the recordmcount main and file.o have different endianness.
The z2 machine calls pxa27x_set_pwrmode() in order to power off
the machine, but this function gets discarded early at boot because
it is marked __init, as pointed out by kbuild:
WARNING: vmlinux.o(.text+0x145c4): Section mismatch in reference from the function z2_power_off() to the function .init.text:pxa27x_set_pwrmode()
The function z2_power_off() references
the function __init pxa27x_set_pwrmode().
This is often because z2_power_off lacks a __init
annotation or the annotation of pxa27x_set_pwrmode is wrong.
This removes the __init section modifier to fix rebooting and the
build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: ba4a90a6d86a ("ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The iomap[] array has PCIM_IOMAP_MAX (6) elements and not
DEVICE_COUNT_RESOURCE (16). This bug was found using a static checker.
It may be that the "if (!(mask & (1 << i)))" check means we never
actually go past the end of the array in real life.
1) The done label was in the wrong place so we didn't copy any
information out when there was no command given.
2) We were using PAGE_SIZE as the size of the buffer instead of
"PAGE_SIZE - pos".
3) snprintf() returns the number of characters that would have been
printed if there were enough space. If there was not enough space
(and we had fixed the memory corruption bug #2) then it would result
in an information leak when we do simple_read_from_buffer(). I've
changed it to use scnprintf() instead.
I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.
Fixes: 5e6e3a92b9a4 ('wireless: mwifiex: initial commit for Marvell mwifiex driver') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.
Fixes: b5874f33bbaf ("wm831x_power: Use genirq") Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.
Fixes: 615f7b9bb1f8 ("mac80211: add driver RSSI threshold events") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
On Xen PV, regs->flags doesn't reliably reflect IOPL and the
exit-to-userspace code doesn't change IOPL. We need to context
switch it manually.
I'm doing this without going through paravirt because this is
specific to Xen PV. After the dust settles, we can merge this with
the 32-bit code, tidy up the iopl syscall implementation, and remove
the set_iopl pvop entirely.
Fixes XSA-171.
Reviewewd-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <JBeulich@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/693c3bd7aeb4d3c27c92c622b7d0f554a458173c.1458162709.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
[ kamal: backport to 3.19-stable: no X86_FEATURE_XENPV so just call
xen_pv_domain() directly ] Acked-by: Andy Lutomirski <luto <at> kernel.org> Signed-off-by: Kamal Mostafa <kamal <at> canonical.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Using sendfile with below small program to get MD5 sums of some files,
it appear that big files (over 64kbytes with 4k pages system) get a
wrong MD5 sum while small files get the correct sum.
This program uses sendfile() to send a file to an AF_ALG socket
for hashing.
After investivation, it appears that sendfile() sends the files by blocks
of 64kbytes (16 times PAGE_SIZE). The problem is that at the end of each
block, the SPLICE_F_MORE flag is missing, therefore the hashing operation
is reset as if it was the end of the file.
This patch adds SPLICE_F_MORE to the flags when more data is pending.
Ben Hutchings [Sat, 13 Feb 2016 02:34:52 +0000 (02:34 +0000)]
pipe: Fix buffer offset after partially failed read
Quoting the RHEL advisory:
> It was found that the fix for CVE-2015-1805 incorrectly kept buffer
> offset and buffer length in sync on a failed atomic read, potentially
> resulting in a pipe buffer state corruption. A local, unprivileged user
> could use this flaw to crash the system or leak kernel memory to user
> space. (CVE-2016-0774, Moderate)
The same flawed fix was applied to stable branches from 2.6.32.y to
3.14.y inclusive, and I was able to reproduce the issue on 3.2.y.
We need to give pipe_iov_copy_to_user() a separate offset variable
and only update the buffer offset if it succeeds.
References: https://rhn.redhat.com/errata/RHSA-2016-0103.html Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Jeffrey Vander Stoep <jeffv@google.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
usb_parse_ss_endpoint_companion() now decodes the burst multiplier
correctly in order to check that it's <= 3, but still uses the wrong
expression if warning that it's > 3.
Fixes: ff30cbc8da42 ("usb: Use the USB_SS_MULT() macro to get the ...") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If raid1d is handling a mix of read and write errors, handle_read_error's
call to freeze_array can get stuck.
This can happen because, though the bio_end_io_list is initially drained,
writes can be added to it via handle_write_finished as the retry_list
is processed. These writes contribute to nr_pending but are not included
in nr_queued.
If a later entry on the retry_list triggers a call to handle_read_error,
freeze array hangs waiting for nr_pending == nr_queued+extra. The writes
on the bio_end_io_list aren't included in nr_queued so the condition will
never be satisfied.
To prevent the hang, include bio_end_io_list writes in nr_queued.
There's probably a better way to handle decrementing nr_queued, but this
seemed like the safest way to avoid breaking surrounding code.
I'm happy to supply the script I used to repro this hang.
Fixes: 55ce74d4bfe1b(md/raid1: ensure device failure recorded before write request returns.) Signed-off-by: Nate Dailey <nate.dailey@stratus.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
When pci_pool_alloc fails in mvs_task_prep then task->lldd_task stays
NULL but it's later used in mvs_abort_task as slot which is passed
to mvs_slot_task_free causing NULL pointer dereference.
Just return from mvs_slot_task_free when passed with NULL slot.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101891 Signed-off-by: Dāvis Mosāns <davispuh@gmail.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
btree_split_beneath()'s error path had an outstanding FIXME that speaks
directly to the potential for _not_ cleaning up a previously allocated
bufio-backed block.
Fix this by releasing the previously allocated bufio block using
unlock_block().
Reported-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <thornber@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Now you should not ask kernel to do a stupid stuff like copying 256MB in
2-byte chunks and call fsync(2) after each chunk but if you do, sysadmin
should have a way to stop you.
We actually do have a check for fatal_signal_pending() in
generic_perform_write() which triggers in this path however because we
always succeed in writing something before the check is done, we return
value > 0 from generic_perform_write() and thus the information about
signal gets lost.
Fix the problem by doing the signal check before writing anything. That
way generic_perform_write() returns -EINTR, the error gets propagated up
and the sendfile loop terminates early.
Signed-off-by: Jan Kara <jack@suse.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
On nv50+, we restrict the valid domains to just the one where the buffer
was originally created. However after the buffer is evicted to system
memory, we might move it back to a different domain that was not
originally valid. When sharing the buffer and retrieving its GEM_INFO
data, we still want the domain that will be valid for this buffer in a
pushbuf, not the one where it currently happens to be.
This resolves fdo#92504 and several others. These are due to suspend
evicting all buffers, making it more likely that they temporarily end up
in the wrong place.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92504 Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
During device assignment/deassignment the flags in the DTE
get lost, which might cause spurious faults, for example
when the device tries to access the system management range.
Fix this by not clearing the flags with the rest of the DTE.
Reported-by: G. Richard Bellamy <rbellamy@pteradigm.com> Tested-by: G. Richard Bellamy <rbellamy@pteradigm.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
There are 24 EQ registers not 25, I suspect this bug came about because
the registers start at EQ1 not zero. The bug is relatively harmless as
the extra register written is an unused one.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Currently a number of Crypto API operations may fail when a signal
occurs. This causes nasty problems as the caller of those operations
are often not in a good position to restart the operation.
In fact there is currently no need for those operations to be
interrupted by user signals at all. All we need is for them to
be killable.
This patch replaces the relevant calls of signal_pending with
fatal_signal_pending, and wait_for_completion_interruptible with
wait_for_completion_killable, respectively.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Zefan Li <lizefan@huawei.com>
We received several reports of systems rebooting and powering on
after an attempted shutdown. Testing showed that setting
XHCI_SPURIOUS_WAKEUP quirk in addition to the XHCI_SPURIOUS_REBOOT
quirk allowed the system to shutdown as expected for LynxPoint-LP
xHCI controllers. Set the quirk back.
Note that the quirk was originally introduced for LynxPoint and
LynxPoint-LP just for this same reason. See:
commit 638298dc66ea ("xhci: Fix spurious wakeups after S5 on Haswell")
It was later limited to only concern HP machines as it caused
regression on some machines, see both bug and commit:
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
commit 6962d914f317 ("xhci: Limit the spurious wakeup fix only to HP machines")
Later it was discovered that the powering on after shutdown
was limited to LynxPoint-LP (Haswell-ULT) and that some non-LP HP
machine suffered from spontaneous resume from S3 (which should
not be related to the SPURIOUS_WAKEUP quirk at all). An attempt
to fix this then removed the SPURIOUS_WAKEUP flag usage completely.
commit b45abacde3d5 ("xhci: no switching back on non-ULT Haswell")
Current understanding is that LynxPoint-LP (Haswell ULT) machines
need the SPURIOUS_WAKEUP quirk, otherwise they will restart, and
plain Lynxpoint (Haswell) machines may _not_ have the quirk
set otherwise they again will restart.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org> Cc: Takashi Iwai <tiwai@suse.de> Cc: Oliver Neukum <oneukum@suse.com>
[Added more history to commit message -Mathias] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If a host fails to wake up a isochronous SuperSpeed device from U1/U2
in time for a isoch transfer it will generate a "No ping response error"
Host will then move to the next transfer descriptor.
Handle this case in the same way as missed service errors, tag the
current TD as skipped and handle it on the next transfer event.
In preparation for the installation of a large page, any small page
tables that may still exist in the target IOV address range are
removed. However, if a scatter/gather list entry is large enough to
fit more than one large page, the address space for any subsequent
large pages is not cleared of conflicting small page tables.
This can cause legitimate mapping requests to fail with errors of the
form below, potentially followed by a series of IOMMU faults:
ERROR: DMA PTE for vPFN 0xfde00 already set (to 7f83a4003 not 7e9e00083)
In this example, a 4MiB scatter/gather list entry resulted in the
successful installation of a large page @ vPFN 0xfdc00, followed by
a failed attempt to install another large page @ vPFN 0xfde00, due to
the presence of a pointer to a small page table @ 0x7f83a4000.
To address this problem, compute the number of large pages that fit
into a given scatter/gather list entry, and use it to derive the
last vPFN covered by the large page(s).
Signed-off-by: Christian Zander <christian@nervanasys.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[bwh: Backported to 3.2:
- Add the lvl_pages variable, added by an earlier commit upstream
- Also change arguments to dma_pte_clear_range(), which is called by
dma_pte_free_pagetable() upstream] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
Unlike shash algorithms, ahash drivers must implement export
and import as their descriptors may contain hardware state and
cannot be exported as is. Unfortunately some ahash drivers did
not provide them and end up causing crashes with algif_hash.
This patch adds a check to prevent these drivers from registering
ahash algorithms until they are fixed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Zefan Li <lizefan@huawei.com>
xen-blkfront will crash if the check to talk_to_blkback()
in blkback_changed()(XenbusStateInitWait) returns an error.
The driver data is freed and info is set to NULL. Later during
the close process via talk_to_blkback's call to xenbus_dev_fatal()
the null pointer is passed to and dereference in blkfront_closing.
Signed-off-by: Cathy Avery <cathy.avery@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
When OSS emulation is loaded on ISA SB AWE32 chip, we get now kernel
warnings like:
WARNING: CPU: 0 PID: 2791 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x51/0x80()
sysfs: cannot create duplicate filename '/devices/isa/sbawe.0/sound/card0/seq-oss-0-0'
It's because both emux synth and opl3 drivers try to register their
OSS device object with the same static index number 0. This hasn't
been a big problem until the recent rewrite of device management code
(that exposes sysfs at the same time), but it's been an obvious bug.
This patch works around it just by using a different index number of
emux synth object. There can be a more elegant way to fix, but it's
enough for now, as this code won't be touched so often, in anyway.
Reported-and-tested-by: Michael Shell <list1@michaelshell.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
There seems to be two problems causing this issue.
First, in drivers/tty/n_tty.c, __receive_buf() stores the data and
updates ldata->commit_head using smp_store_release() and then checks
the wait queue using waitqueue_active(). However, since there is no
memory barrier, __receive_buf() could return without calling
wake_up_interactive_poll(), and at the same time, n_tty_read() could
start to wait in wait_woken() as in the following chart.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
if (waitqueue_active(&tty->read_wait))
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
add_wait_queue(&tty->read_wait, &wait);
...
if (!input_available_p(tty, 0)) {
smp_store_release(&ldata->commit_head,
ldata->read_head);
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
The second problem is that n_tty_read() also lacks a memory barrier
call and could also cause __receive_buf() to return without calling
wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken()
as in the chart below.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
spin_lock_irqsave(&q->lock, flags);
/* from add_wait_queue() */
...
if (!input_available_p(tty, 0)) {
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
smp_store_release(&ldata->commit_head,
ldata->read_head);
if (waitqueue_active(&tty->read_wait))
__add_wait_queue(q, wait);
spin_unlock_irqrestore(&q->lock,flags);
/* from add_wait_queue() */
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
There are also other places in drivers/tty/n_tty.c which have similar
calls to waitqueue_active(), so instead of adding many memory barrier
calls, this patch simply removes the call to waitqueue_active(),
leaving just wake_up*() behind.
This fixes both problems because, even though the memory access before
or after the spinlocks in both wake_up*() and add_wait_queue() can
sneak into the critical section, it cannot go past it and the critical
section assures that they will be serialized (please see "INTER-CPU
ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a
better explanation). Moreover, the resulting code is much simpler.
Latency measurement using a ping-pong test over a pty doesn't show any
visible performance drop.
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4:
- adjust context
- s/wake_up_interruptible_poll/wake_up_interruptible/
- drop changes to __receive_buf() and n_tty_set_termios()] Signed-off-by: Zefan Li <lizefan@huawei.com>
Add a device quirk for the Logitech PTZ Pro Camera and its sibling the
ConferenceCam CC3000e Camera.
This fixes the failed camera enumeration on some boot, particularly on
machines with fast CPU.
Tested by connecting a Logitech PTZ Pro Camera to a machine with a
Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles
while recording the kernel logs and taking camera picture after each boot.
Before the patch, more than 7% of the boots show some enumeration transfer
failures and in a few of them, the kernel is giving up before actually
enumerating the webcam. After the patch, the enumeration has been correct
on every reboot.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
I think I find a linux bug, I have the test cases is constructed. I
can stable recurring problems in fedora22(4.0.4) kernel version,
arch for x86_64. I construct transparent huge page, when the parent
and child process with MAP_SHARE, MAP_PRIVATE way to access the same
huge page area, it has the opportunity to lead to huge page copy on
write failure, and then it will munmap the child corresponding mmap
area, but then the child mmap area with VM_MAYSHARE attributes, child
process munmap this area can trigger VM_BUG_ON in set_vma_resv_flags
functions (vma - > vm_flags & VM_MAYSHARE).
There were a number of problems with the report (e.g. it's hugetlbfs that
triggers this, not transparent huge pages) but it was fundamentally
correct in that a VM_BUG_ON in set_vma_resv_flags() can be triggered that
looks like this
vma ffff8804651fd0d0 start 00007fc474e00000 end 00007fc475e00000
next ffff8804651fd018 prev ffff8804651fd188 mm ffff88046b1b1800
prot 8000000000000027 anon_vma (null) vm_ops ffffffff8182a7a0
pgoff 0 file ffff88106bdb9800 private_data (null)
flags: 0x84400fb(read|write|shared|mayread|maywrite|mayexec|mayshare|dontexpand|hugetlb)
------------
kernel BUG at mm/hugetlb.c:462!
SMP
Modules linked in: xt_pkttype xt_LOG xt_limit [..]
CPU: 38 PID: 26839 Comm: map Not tainted 4.0.4-default #1
Hardware name: Dell Inc. PowerEdge R810/0TT6JF, BIOS 2.7.4 04/26/2012
set_vma_resv_flags+0x2d/0x30
The VM_BUG_ON is correct because private and shared mappings have
different reservation accounting but the warning clearly shows that the
VMA is shared.
When a private COW fails to allocate a new page then only the process
that created the VMA gets the page -- all the children unmap the page.
If the children access that data in the future then they get killed.
The problem is that the same file is mapped shared and private. During
the COW, the allocation fails, the VMAs are traversed to unmap the other
private pages but a shared VMA is found and the bug is triggered. This
patch identifies such VMAs and skips them.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Reported-by: SunDong <sund_sky@126.com> Reviewed-by: Michal Hocko <mhocko@suse.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: David Rientjes <rientjes@google.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Per-IRQ directories in procfs are created only when a handler is first
added to the irqdesc, not when the irqdesc is created. In the case of
a shared IRQ, multiple tasks can race to create a directory. This
race condition seems to have been present forever, but is easier to
hit with async probing.
Dmitry Vyukov reported the following using trinity and the memory
error detector AddressSanitizer
(https://code.google.com/p/address-sanitizer/wiki/AddressSanitizerForKernel).
[ 124.575597] ERROR: AddressSanitizer: heap-buffer-overflow on
address ffff88002e280000
[ 124.576801] ffff88002e280000 is located 131938492886538 bytes to
the left of 28857600-byte region [ffffffff81282e0a, ffffffff82e0830a)
[ 124.578633] Accessed by thread T10915:
[ 124.579295] inlined in describe_heap_address
./arch/x86/mm/asan/report.c:164
[ 124.579295] #0 ffffffff810dd277 in asan_report_error
./arch/x86/mm/asan/report.c:278
[ 124.580137] #1 ffffffff810dc6a0 in asan_check_region
./arch/x86/mm/asan/asan.c:37
[ 124.581050] #2 ffffffff810dd423 in __tsan_read8 ??:0
[ 124.581893] #3 ffffffff8107c093 in get_wchan
./arch/x86/kernel/process_64.c:444
The address checks in the 64bit implementation of get_wchan() are
wrong in several ways:
- The lower bound of the stack is not the start of the stack
page. It's the start of the stack page plus sizeof (struct
thread_info)
The 2 * sizeof(unsigned long) is required because the stack pointer
points at the frame pointer. The layout on the stack is: ... IP FP
... IP FP. So we need to make sure that both IP and FP are in the
bounds.
Fix the bound checks and get rid of the mix of numeric constants, u64
and unsigned long. Making all unsigned long allows us to use the same
function for 32bit as well.
Use READ_ONCE() when accessing the stack. This does not prevent a
concurrent wakeup of the task and the stack changing, but at least it
avoids TOCTOU.
Also check task state at the end of the loop. Again that does not
prevent concurrent changes, but it avoids walking for nothing.
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Signed-off-by: Sheng Yong <shengyong1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Zefan Li <lizefan@huawei.com>
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at>
[lizf: Backported to 3.4: use dbg_err() instead of ubi_err()]; Signed-off-by: Zefan Li <lizefan@huawei.com>
Sanitizing the e820 map may produce extra E820 entries which would result in
the topmost E820 entries being removed. The removed entries would typically
include the top E820 usable RAM region and thus result in the domain having
signicantly less RAM available to it.
Fix by allowing sanitize_e820_map to use the full size of the allocated E820
array.
Signed-off-by: Malcolm Crossley <malcolm.crossley@citrix.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com>
[lizf: Backported to 3.4: s/map/xen_e820_map] Signed-off-by: Zefan Li <lizefan@huawei.com>
Make sure the compiler does not modify arguments of syscall functions.
This can happen if the compiler generates a tailcall to another
function. For example, without asmlinkage_protect sys_openat is compiled
into this function:
Note how the fourth argument is modified in place, modifying the register
%d4 that gets restored from this stack slot when the function returns to
user-space. The caller may expect the register to be unmodified across
system calls.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org> Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
ath9k inserts padding between the 802.11 header and the data area (to
align it). Since it didn't declare this extra required headroom, this
led to some nasty issues like randomly dropped packets in some setups.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The order of the following three spinlocks should be:
dlm_domain_lock < dlm_ctxt->spinlock < dlm_lock_resource->spinlock
But dlm_dispatch_assert_master() is called while holding
dlm_ctxt->spinlock and dlm_lock_resource->spinlock, and then it calls
dlm_grab() which will take dlm_domain_lock.
Once another thread (for example, dlm_query_join_handler) has already
taken dlm_domain_lock, and tries to take dlm_ctxt->spinlock deadlock
happens.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Mark Fasheh <mfasheh@suse.com> Cc: "Junxiao Bi" <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Linux cifs mount with ntlmssp against an Mac OS X (Yosemite
10.10.5) share fails in case the clocks differ more than +/-2h:
digest-service: digest-request: od failed with 2 proto=ntlmv2
digest-service: digest-request: kdc failed with -1561745592 proto=ntlmv2
Fix this by (re-)using the given server timestamp for the
ntlmv2 authentication (as Windows 7 does).
A related problem was also reported earlier by Namjae Jaen (see below):
Windows machine has extended security feature which refuse to allow
authentication when there is time difference between server time and
client time when ntlmv2 negotiation is used. This problem is prevalent
in embedded enviornment where system time is set to default 1970.
Modern servers send the server timestamp in the TargetInfo Av_Pair
structure in the challenge message [see MS-NLMP 2.2.2.1]
In [MS-NLMP 3.1.5.1.2] it is explicitly mentioned that the client must
use the server provided timestamp if present OR current time if it is
not
Reported-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Peter Seiderer <ps.report@gmx.net> Signed-off-by: Steve French <smfrench@gmail.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Some changes between xhci 0.96 and xhci 1.0 specifications forced us to
check the hci version in code, some of these checks were implemented as
hci_version == 1.0, which will not work with new xhci 1.1 controllers.
xhci 1.1 behaves similar to xhci 1.0 in these cases, so change these
checks to hci_version >= 1.0
These have roughly the same purpose as the SMRR, which we do not need
to implement in KVM. However, Linux accesses MSR_K8_TSEG_ADDR at
boot, which causes problems when running a Xen dom0 under KVM.
Just return 0, meaning that processor protection of SMRAM is not
in effect.
Reported-by: M A Young <m.a.young@durham.ac.uk> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The in kernel snprintf() will conveniently return the actual length of
the printed string even if not given an output beffer at all so just do
that rather than relying on the user to pass in a suitable buffer,
ensuring that we don't need to worry if the buffer was truncated due to
the size of the buffer passed in.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If a read is attempted which is smaller than the line length then we may
underflow the subtraction we're doing with the unsigned size_t type so
move some of the calculation to be additions on the right hand side
instead in order to avoid this.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
In btrfs_evict_inode, we properly truncate the page cache for evicted
inodes but then we call btrfs_wait_ordered_range for every inode as well.
It's the right thing to do for regular files but results in incorrect
behavior for device inodes for block devices.
filemap_fdatawrite_range gets called with inode->i_mapping which gets
resolved to the block device inode before getting passed to
wbc_attach_fdatawrite_inode and ultimately to inode_to_bdi. What happens
next depends on whether there's an open file handle associated with the
inode. If there is, we write to the block device, which is unexpected
behavior. If there isn't, we through normally and inode->i_data is used.
We can also end up racing against open/close which can result in crashes
when i_mapping points to a block device inode that has been closed.
Since there can't be any page cache associated with special file inodes,
it's safe to skip the btrfs_wait_ordered_range call entirely and avoid
the problem.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100911 Tested-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Actually, spi_master_put() after spi_alloc_master() must _not_ be followed
by kfree(). The memory is already freed with the call to spi_master_put()
through spi_master_class, which registers a release function. Calling both
spi_master_put() and kfree() results in often nasty (and delayed) crashes
elsewhere in the kernel, often in the networking stack.
Link to patch and concerns: https://lkml.org/lkml/2012/9/3/269
or
http://lkml.iu.edu/hypermail/linux/kernel/1209.0/00790.html
Alexey Klimov: This revert becomes valid after 94c69f765f1b4a658d96905ec59928e3e3e07e6a when spi-imx.c
has been fixed and there is no need to call kfree() so comment
for spi_alloc_master() should be fixed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
On Intel Baytrail, there is case when interrupt handler get called, no SPI
message is captured. The RX FIFO is indeed empty when RX timeout pending
interrupt (SSSR_TINT) happens.
Use the BIOS version where both HSUART and SPI are on the same IRQ. Both
drivers are using IRQF_SHARED when calling the request_irq function. When
running two separate and independent SPI and HSUART application that
generate data traffic on both components, user will see messages like
below on the console:
pxa2xx-spi pxa2xx-spi.0: bad message state in interrupt handler
This commit will fix this by first checking Receiver Time-out Interrupt,
if it is disabled, ignore the request and return without servicing.
Signed-off-by: Tan, Jui Nee <jui.nee.tan@intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The size here comes from the user via the ioctl, it is a number between
1-u32max so the addition here could overflow on 32 bit systems.
Fixes: f453ba046074 ('DRM: add mode setting support') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Daniel Stone <daniels@collabora.com> Signed-off-by: Dave Airlie <airlied@gmail.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
When a write fails and a bad-block-list is present, we can
update the bad-block-list instead of writing the data. If
this succeeds then it is OK clear the relevant bitmap-bit as
no further 'sync' of the block is needed.
However if writing the bad-block-list fails then we need to
treat the write as failed and particularly must not clear
the bitmap bit. Otherwise the device can be re-added (after
any hardware connection issues are resolved) and because the
relevant bit in the bitmap is clear, that block will not be
resynced. This leads to data corruption.
We already delay the final bio_endio() on the write until
the bad-block-list is written so that when the write
returns: either that data is safe, the bad-block record is
safe, or the fact that the device is faulty is safe.
However we *don't* delay the clearing of the bitmap, so the
bitmap bit can be recorded as cleared before we know if the
bad-block-list was written safely.
So: delay that until the write really is safe.
i.e. move the call to close_write() until just before
calling bio_endio(), and recheck the 'is array degraded'
status before making that call.
This bug goes back to v3.1 when bad-block-lists were
introduced, though it only affects arrays created with
mdadm-3.3 or later as only those have bad-block lists.
Backports will require at least
Commit: 55ce74d4bfe1 ("md/raid1: ensure device failure recorded before write request returns.")
as well. I'll send that to 'stable' separately.
Note that of the two tests of R1BIO_WriteError that this
patch adds, the first is certain to fail and the second is
certain to succeed. However doing it this way makes the
patch more obviously correct. I will tidy the code up in a
future merge window.
When a write to one of the legs of a RAID1 fails, the failure is
recorded in the metadata of the other leg(s) so that after a restart
the data on the failed drive wont be trusted even if that drive seems
to be working again (maybe a cable was unplugged).
Similarly when we record a bad-block in response to a write failure,
we must not let the write complete until the bad-block update is safe.
Currently there is no interlock between the write request completing
and the metadata update. So it is possible that the write will
complete, the app will confirm success in some way, and then the
machine will crash before the metadata update completes.
This is an extremely small hole for a racy to fit in, but it is
theoretically possible and so should be closed.
So:
- set MD_CHANGE_PENDING when requesting a metadata update for a
failed device, so we can know with certainty when it completes
- queue requests that experienced an error on a new queue which
is only processed after the metadata update completes
- call raid_end_bio_io() on bios in that queue when the time comes.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
projects / thirdparty / kernel / stable.git / log
