As per JEDEC Standard No. 223E Section 5.9.2, the max # active commands
value programmed by the host sw in MCQConfig.MAC should be one less than
the actual value.
Signed-off-by: Rohit Ner <rohitner@google.com> Link: https://lore.kernel.org/r/20240220095637.2900067-1-rohitner@google.com Reviewed-by: Peter Wang <peter.wang@mediatek.com> Reviewed-by: Can Guo <quic_cang@quicinc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit(f55c096f62f1 exfat: do not zero the extended part) changed
the timing of synchronizing bitmap and inode in exfat_cont_expand().
The change caused xfstests generic/013 to fail if 'dirsync' or 'sync'
is enabled. So this commit restores the timing.
Fixes: f55c096f62f1 ("exfat: do not zero the extended part") Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
vgic_v2_parse_attr() is responsible for finding the vCPU that matches
the user-provided CPUID, which (of course) may not be valid. If the ID
is invalid, kvm_get_vcpu_by_id() returns NULL, which isn't handled
gracefully.
Similar to the GICv3 uaccess flow, check that kvm_get_vcpu_by_id()
actually returns something and fail the ioctl if not.
Cc: stable@vger.kernel.org Fixes: 7d450e282171 ("KVM: arm/arm64: vgic-new: Add userland access to VGIC dist registers") Reported-by: Alexander Potapenko <glider@google.com> Tested-by: Alexander Potapenko <glider@google.com> Reviewed-by: Alexander Potapenko <glider@google.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20240424173959.3776798-2-oliver.upton@linux.dev Signed-off-by: Oliver Upton <oliver.upton@linux.dev> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using restricted DMA pools (CONFIG_DMA_RESTRICTED_POOL=y) in conjunction
with dynamic SWIOTLB (CONFIG_SWIOTLB_DYNAMIC=y) leads to the following
crash when initialising the restricted pools at boot-time:
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
| Internal error: Oops: 0000000096000005 [#1] PREEMPT SMP
| pc : rmem_swiotlb_device_init+0xfc/0x1ec
| lr : rmem_swiotlb_device_init+0xf0/0x1ec
| Call trace:
| rmem_swiotlb_device_init+0xfc/0x1ec
| of_reserved_mem_device_init_by_idx+0x18c/0x238
| of_dma_configure_id+0x31c/0x33c
| platform_dma_configure+0x34/0x80
faddr2line reveals that the crash is in the list validation code:
because add_mem_pool() is trying to list_add_rcu() to a NULL
'mem->pools'.
Fix the crash by initialising the 'mem->pools' list_head in
rmem_swiotlb_device_init() before calling add_mem_pool().
Reported-by: Nikita Ioffe <ioffe@google.com> Tested-by: Nikita Ioffe <ioffe@google.com> Fixes: 1aaa736815eb ("swiotlb: allocate a new memory pool when existing pools are full") Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
At the time of LPAR boot up, partition firmware provides Open Firmware
property ibm,dma-window for the PE. This property is provided on the PCI
bus the PE is attached to.
There are execptions where the partition firmware might not provide this
property for the PE at the time of LPAR boot up. One of the scenario is
where the firmware has frozen the PE due to some error condition. This
PE is frozen for 24 hours or unless the whole system is reinitialized.
Within this time frame, if the LPAR is booted, the frozen PE will be
presented to the LPAR but ibm,dma-window property could be missing.
Today, under these circumstances, the LPAR oopses with NULL pointer
dereference, when configuring the PCI bus the PE is attached to.
Fixes: b1fc44eaa9ba ("pseries/iommu/ddw: Fix kdump to work in absence of ibm,dma-window") Signed-off-by: Gaurav Batra <gbatra@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240422205141.10662-1-gbatra@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, plpks_confirm_object_flushed() function polls for 5msec in
total instead of 5sec.
Keep max polling time consistent for all the H_CALLs, which take longer
than expected, to be 5sec. Also, make use of fsleep() everywhere to
insert delay.
Reported-by: Nageswara R Sastry <rnsastry@linux.ibm.com> Fixes: 2454a7af0f2a ("powerpc/pseries: define driver for Platform KeyStore") Signed-off-by: Nayna Jain <nayna@linux.ibm.com> Tested-by: Nageswara R Sastry <rnsastry@linux.ibm.com> Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20240418031230.170954-1-nayna@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
While PLL CPUX clock rate change when CPU is running from it works in
vast majority of cases, now and then it causes instability. This leads
to system crashes and other undefined behaviour. After a lot of testing
(30+ hours) while also doing a lot of frequency switches, we can't
observe any instability issues anymore when doing reparenting to stable
clock like 24 MHz oscillator.
Contrary to i915, in xe ADL-N is kept as a different platform, not a
subplatform of ADL-P. Since the display side doesn't need to
differentiate between P and N, i.e. IS_ALDERLAKE_P_N() is never called,
just fixup the compat header to check for both P and N.
Moving ADL-N to be a subplatform would be more complex as the firmware
loading in xe only handles platforms, not subplatforms, as going forward
the direction is to check on IP version rather than
platforms/subplatforms.
Fix warning when initializing display:
xe 0000:00:02.0: [drm:intel_pch_type [xe]] Found Alder Lake PCH
------------[ cut here ]------------
xe 0000:00:02.0: drm_WARN_ON(!((dev_priv)->info.platform == XE_ALDERLAKE_S) && !((dev_priv)->info.platform == XE_ALDERLAKE_P))
GRO-GSO path is supposed to be transparent and as such L3 flush checks are
relevant to all UDP flows merging in GRO. This patch uses the same logic
and code from tcp_gro_receive, terminating merge if flush is non zero.
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.") Signed-off-by: Richard Gobert <richardbgobert@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commits a602456 ("udp: Add GRO functions to UDP socket") and 57c67ff ("udp:
additional GRO support") introduce incorrect usage of {ip,ipv6}_hdr in the
complete phase of gro. The functions always return skb->network_header,
which in the case of encapsulated packets at the gro complete phase, is
always set to the innermost L3 of the packet. That means that calling
{ip,ipv6}_hdr for skbs which completed the GRO receive phase (both in
gro_list and *_gro_complete) when parsing an encapsulated packet's _outer_
L3/L4 may return an unexpected value.
This incorrect usage leads to a bug in GRO's UDP socket lookup.
udp{4,6}_lib_lookup_skb functions use ip_hdr/ipv6_hdr respectively. These
*_hdr functions return network_header which will point to the innermost L3,
resulting in the wrong offset being used in __udp{4,6}_lib_lookup with
encapsulated packets.
This patch adds network_offset and inner_network_offset to napi_gro_cb, and
makes sure both are set correctly.
To fix the issue, network_offsets union is used inside napi_gro_cb, in
which both the outer and the inner network offsets are saved.
Reproduction example:
Endpoint configuration example (fou + local address bind)
# ip fou add port 6666 ipproto 4
# ip link add name tun1 type ipip remote 2.2.2.1 local 2.2.2.2 encap fou encap-dport 5555 encap-sport 6666 mode ipip
# ip link set tun1 up
# ip a add 1.1.1.2/24 dev tun1
Netperf TCP_STREAM result on net-next before patch is applied:
Fixes: a6024562ffd7 ("udp: Add GRO functions to UDP socket") Signed-off-by: Richard Gobert <richardbgobert@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
KMSAN reported uninit-value access in __ip_make_skb() [1]. __ip_make_skb()
tests HDRINCL to know if the skb has icmphdr. However, HDRINCL can cause a
race condition. If calling setsockopt(2) with IP_HDRINCL changes HDRINCL
while __ip_make_skb() is running, the function will access icmphdr in the
skb even if it is not included. This causes the issue reported by KMSAN.
Check FLOWI_FLAG_KNOWN_NH on fl4->flowi4_flags instead of testing HDRINCL
on the socket.
Also, fl4->fl4_icmp_type and fl4->fl4_icmp_code are not initialized. These
are union in struct flowi4 and are implicitly initialized by
flowi4_init_output(), but we should not rely on specific union layout.
In one case the -1 is returned which is quite confusing code for
the wrong device ID, in another the ret is returning instead of
plain 0 that also confusing as readed may ask the possible meaning
of positive codes, which are never the case there. Convert both
to use explicit predefined error codes to make it clear what's going
on there.
GPIO controller might not be available when driver is being probed.
There are plenty of reasons why, one of which is deferred probe.
Since GPIOs are optional, return any error code we got to the upper
layer, including deferred probe. With that in mind, use dev_err_probe()
in order to avoid spamming the logs.
Symptom:
When the hsuid attribute is set for the first time on an IQD Layer3
device while the corresponding network interface is already UP,
the kernel will try to execute a napi function pointer that is NULL.
Analysis:
There is one napi structure per out_q: card->qdio.out_qs[i].napi
The napi.poll functions are set during qeth_open().
Since
commit 1cfef80d4c2b ("s390/qeth: Don't call dev_close/dev_open (DOWN/UP)")
qeth_set_offline()/qeth_set_online() no longer call dev_close()/
dev_open(). So if qeth_free_qdio_queues() cleared
card->qdio.out_qs[i].napi.poll while the network interface was UP and the
card was offline, they are not set again.
Reproduction:
chzdev -e $devno layer2=0
ip link set dev $network_interface up
echo 0 > /sys/bus/ccwgroup/devices/0.0.$devno/online
echo foo > /sys/bus/ccwgroup/devices/0.0.$devno/hsuid
echo 1 > /sys/bus/ccwgroup/devices/0.0.$devno/online
-> Crash (can be enforced e.g. by af_iucv connect(), ip link down/up, ...)
Note that a Completion Queue (CQ) is only enabled or disabled, when hsuid
is set for the first time or when it is removed.
Workarounds:
- Set hsuid before setting the device online for the first time
or
- Use chzdev -d $devno; chzdev $devno hsuid=xxx; chzdev -e $devno;
to set hsuid on an existing device. (this will remove and recreate the
network interface)
Fix:
There is no need to free the output queues when a completion queue is
added or removed.
card->qdio.state now indicates whether the inbound buffer pool and the
outbound queues are allocated.
card->qdio.c_q indicates whether a CQ is allocated.
Fixes: 1cfef80d4c2b ("s390/qeth: Don't call dev_close/dev_open (DOWN/UP)") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240430091004.2265683-1-wintera@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure the inner IP header is part of skb's linear data before reading
its ECN bits. Otherwise we might read garbage.
One symptom is the system erroneously logging errors like
"vxlan: non-ECT from xxx.xxx.xxx.xxx with TOS=xxxx".
Similar bugs have been fixed in geneve, ip_tunnel and ip6_tunnel (see
commit 1ca1ba465e55 ("geneve: make sure to pull inner header in
geneve_rx()") for example). So let's reuse the same code structure for
consistency. Maybe we'll can add a common helper in the future.
The find connection logic of Transarc's Rx was modified in the mid-1990s
to support multi-homed servers which might send a response packet from
an address other than the destination address in the received packet.
The rules for accepting a packet by an Rx initiator (RX_CLIENT_CONNECTION)
were altered to permit acceptance of a packet from any address provided
that the port number was unchanged and all of the connection identifiers
matched (Epoch, CID, SecurityClass, ...).
This change applies the same rules to the Linux implementation which makes
it consistent with IBM AFS 3.6, Arla, OpenAFS and AuriStorFS.
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: Jeffrey Altman <jaltman@auristor.com> Acked-by: David Howells <dhowells@redhat.com> Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Link: https://lore.kernel.org/r/20240419163057.4141728-1-marc.dionne@auristor.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SKB_GSO_FRAGLIST skbs must not be linearized, otherwise they become
invalid. Return NULL if such an skb is passed to skb_copy or
skb_copy_expand, in order to prevent a crash on a potential later
call to skb_gso_segment.
Fixes: 3a1296a38d0c ("net: Support GRO/GSO fraglist chaining.") Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling skb_copy on a SKB_GSO_FRAGLIST skb is not valid, since it returns
an invalid linearized skb. This code only needs to change the ethernet
header, so pskb_copy is the right function to call here.
Fixes: 6db6f0eae605 ("bridge: multicast to unicast") Signed-off-by: Felix Fietkau <nbd@nbd.name> Acked-by: Paolo Abeni <pabeni@redhat.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If spi_sync() is called with the non-empty queue and the same spi_message
is then reused, the complete callback for the message remains set while
the context is cleared, leading to a null pointer dereference when the
callback is invoked from spi_finalize_current_message().
With function inlining disabled, the call stack might look like this:
_raw_spin_lock_irqsave from complete_with_flags+0x18/0x58
complete_with_flags from spi_complete+0x8/0xc
spi_complete from spi_finalize_current_message+0xec/0x184
spi_finalize_current_message from spi_transfer_one_message+0x2a8/0x474
spi_transfer_one_message from __spi_pump_transfer_message+0x104/0x230
__spi_pump_transfer_message from __spi_transfer_message_noqueue+0x30/0xc4
__spi_transfer_message_noqueue from __spi_sync+0x204/0x248
__spi_sync from spi_sync+0x24/0x3c
spi_sync from mcp251xfd_regmap_crc_read+0x124/0x28c [mcp251xfd]
mcp251xfd_regmap_crc_read [mcp251xfd] from _regmap_raw_read+0xf8/0x154
_regmap_raw_read from _regmap_bus_read+0x44/0x70
_regmap_bus_read from _regmap_read+0x60/0xd8
_regmap_read from regmap_read+0x3c/0x5c
regmap_read from mcp251xfd_alloc_can_err_skb+0x1c/0x54 [mcp251xfd]
mcp251xfd_alloc_can_err_skb [mcp251xfd] from mcp251xfd_irq+0x194/0xe70 [mcp251xfd]
mcp251xfd_irq [mcp251xfd] from irq_thread_fn+0x1c/0x78
irq_thread_fn from irq_thread+0x118/0x1f4
irq_thread from kthread+0xd8/0xf4
kthread from ret_from_fork+0x14/0x28
Fix this by also setting message->complete to NULL when the transfer is
complete.
Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync") Signed-off-by: Mans Rullgard <mans@mansr.com> Link: https://lore.kernel.org/r/20240430182705.13019-1-mans@mansr.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The selftest for the driver sends a dummy packet and checks if the
packet will be received properly as it should be. The regular TX path
and the selftest can use the same network queue so locking is required
and was missing in the selftest path. This was addressed in the commit
cited below.
Unfortunately locking the TX queue requires BH to be disabled which is
not the case in selftest path which is invoked in process context.
Lockdep should be complaining about this.
Use __netif_tx_lock_bh() for TX queue locking.
Fixes: c650e04898072 ("cxgb4: Fix race between loopback and normal Tx path") Reported-by: "John B. Wyatt IV" <jwyatt@redhat.com> Closes: https://lore.kernel.org/all/Zic0ot5aGgR-V4Ks@thinkpad2021/ Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/20240429091147.YWAaal4v@linutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we allocate a lbuf-sized kernel buffer and copy lbuf from
userspace to that buffer. Later, we use scanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using scanf. Fix this issue by using memdup_user_nul instead.
Amlogic sound cards do create a lot of pcm interfaces, possibly more than
8. Some pcm interfaces are internal (like DPCM backends and c2c) and not
exposed to userspace.
Those interfaces still increase the number passed to snd_find_free_minor(),
which eventually exceeds 8 causing -EBUSY error on card registration if
CONFIG_SND_DYNAMIC_MINORS=n and the interface is exposed to userspace.
select CONFIG_SND_DYNAMIC_MINORS for Amlogic cards to avoid the problem.
So far, the formatters have been reset/enabled using the .prepare()
callback. This was done in this callback because walking the formatters use
a mutex. A mutex is used because formatter handling require dealing
possibly slow clock operation.
With the support of non-atomic, .trigger() callback may be used which also
allows to properly enable and disable formatters on start but also
pause/resume.
This solve a random shift on TDMIN as well repeated samples on for TDMOUT.
Non atomic operations need to be performed in the trigger callback
of the TDM interfaces. Those are BEs but what matters is the nonatomic
flag of the FE in the DPCM context. Just set nonatomic for everything so,
at least, what is done is clear.
With the AXG audio subsystem, there is a possible random channel shift on
TDM capture, when the slot number per lane is more than 2, and there is
more than one lane used.
The problem has been there since the introduction of the axg audio support
but such scenario is pretty uncommon. This is why there is no loud
complains about the problem.
Solving the problem require to make the links non-atomic and use the
trigger() callback to start FEs and BEs in the appropriate order.
This was tried in the past and reverted because it caused the block irq to
sleep while atomic. However, instead of reverting, the solution is to call
snd_pcm_period_elapsed() in a non atomic context.
Use the bottom half of a threaded IRQ to do so.
Fixes: 6dc4fa179fb8 ("ASoC: meson: add axg fifo base driver") Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20240426152946.3078805-2-jbrunet@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
VXLAN devices update their stats locklessly. Therefore these counters
should either be stored in per-cpu data structures or the updates
should be done using atomic increments.
Since the net_device_core_stats infrastructure is already used in
vxlan_rcv(), use it for the other rx_dropped and tx_dropped counter
updates. Update the other counters atomically using DEV_STATS_INC().
Fixes: d342894c5d2f ("vxlan: virtual extensible lan") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In qede_flow_spec_to_rule(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced qede_flow_spec_to_rule(),
and this call to qede_parse_flow_attr(), it looks
like it just duplicated how it was already used.
Only compile tested.
Fixes: 37c5d3efd7f8 ("qede: use ethtool_rx_flow_rule() to remove duplicated parser code") Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In qede_add_tc_flower_fltr(), when calling
qede_parse_flow_attr() then the return code
was only used for a non-zero check, and then
-EINVAL was returned.
qede_parse_flow_attr() can currently fail with:
* -EINVAL
* -EOPNOTSUPP
* -EPROTONOSUPPORT
This patch changes the code to use the actual
return code, not just return -EINVAL.
The blaimed commit introduced these functions.
Only compile tested.
Fixes: 2ce9c93eaca6 ("qede: Ingress tc flower offload (drop action) support.") Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Explicitly set 'rc' (return code), before jumping to the
unlock and return path.
By not having any code depend on that 'rc' remains at
it's initial value of -EINVAL, then we can re-use 'rc' for
the return code of function calls in subsequent patches.
Only compile tested.
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: fcee2065a178 ("net: qede: use return from qede_parse_flow_attr() for flower") Signed-off-by: Sasha Levin <sashal@kernel.org>
A side effect of making the dock monitoring interrupt-driven was that
we'd be very quick to program a freshly connected dock. However, for
unclear reasons, the dock does not work when we do that - despite the
FPGA netlist upload going just fine. We work around this by adding a
delay before programming the dock; for safety, the value is several
times as much as was determined empirically.
Note that a badly timed dock hot-plug would have triggered the problem
even before the referenced commit - but now it would happen 100% instead
of about 3% of the time, thus making it impossible to work around by
re-plugging.
The actual event processing was already done by workqueue items. We can
move the event dispatching there as well, rather than doing it already
in the interrupt handler callback.
This change has a rather profound "side effect" on the reliability of
the FPGA programming: once we enter programming mode, we must not issue
any snd_emu1010_fpga_{read,write}() calls until we're done, as these
would badly mess up the programming protocol. But exactly that would
happen when trying to program the dock, as that triggers GPIO interrupts
as a side effect. This is mitigated by deferring the actual interrupt
handling, as workqueue items are not re-entrant.
To avoid scheduling the dispatcher on non-events, we now explicitly
ignore GPIO IRQs triggered by "uninteresting" pins, which happens a lot
as a side effect of calling snd_emu1010_fpga_{read,write}().
Pulled out of the next patch to improve its legibility.
As the function is now available, call it directly from
snd_emu10k1_emu1010_init(), thus making the MicroDock firmware loading
synchronous - there isn't really a reason not to. Note that this does
not affect the AudioDocks of rev1 cards, as these have no independent
power supplies, and thus come up only a while after the main card is
initialized.
As a drive-by, adjust the priorities of two messages to better reflect
their impact.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-3-oswald.buddenhagen@gmx.de>
Stable-dep-of: f848337cd801 ("ALSA: emu10k1: move the whole GPIO event handling to the workqueue") Signed-off-by: Sasha Levin <sashal@kernel.org>
While there are two separate IRQ status bits for dock attach and detach,
the hardware appears to mix them up more or less randomly, making them
useless for tracking what actually happened. It is much safer to check
the dock status separately and proceed based on that, as the old polling
code did.
Note that the code assumes that only the dock can be hot-plugged - if
other option card bits changed, the logic would break.
Fix extract_user_to_sg() so that it will break out of the loop if
iov_iter_extract_pages() returns 0 rather than looping around forever.
[Note that I've included two fixes lines as the function got moved to a
different file and renamed]
Fixes: 85dd2c8ff368 ("netfs: Add a function to extract a UBUF or IOVEC into a BVEC iterator") Fixes: f5f82cd18732 ("Move netfs_extract_iter_to_sg() to lib/scatterlist.c") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: netfs@lists.linux.dev Link: https://lore.kernel.org/r/1967121.1714034372@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return-address (RA) register r14 is specified as volatile in the
s390x ELF ABI [1]. Nevertheless proper CFI directives must be provided
for an unwinder to restore the return address, if the RA register
value is changed from its value at function entry, as it is the case.
Since thermal_debug_cdev_remove() does not run under cdev->lock, it can
run in parallel with thermal_debug_cdev_state_update() and it may free
the struct thermal_debugfs object used by the latter after it has been
checked against NULL.
If that happens, thermal_debug_cdev_state_update() will access memory
that has been freed already causing the kernel to crash.
Address this by using cdev->lock in thermal_debug_cdev_remove() around
the cdev->debugfs value check (in case the same cdev is removed at the
same time in two different threads) and its reset to NULL.
Fixes: 755113d76786 ("thermal/debugfs: Add thermal cooling device debugfs information")
Cc :6.8+ <stable@vger.kernel.org> # 6.8+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner
protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls
skb_mac_gso_segment() to invoke inner protocol GSO handlers.
nsh_gso_segment() does the following for the original skb before
calling skb_mac_gso_segment()
1. reset skb->network_header
2. save the original skb->{mac_heaeder,mac_len} in a local variable
3. pull the NSH header
4. resets skb->mac_header
5. set up skb->mac_len and skb->protocol for the inner protocol.
and does the following for the segmented skb
6. set ntohs(ETH_P_NSH) to skb->protocol
7. push the NSH header
8. restore skb->mac_header
9. set skb->mac_header + mac_len to skb->network_header
10. restore skb->mac_len
There are two problems in 6-7 and 8-9.
(a)
After 6 & 7, skb->data points to the NSH header, so the outer header
(ETH_P_8021AD in this case) is stripped when skb is sent out of netdev.
Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH),
skb_pull() in the first nsh_gso_segment() will make skb->data point
to the middle of the outer NSH or Ethernet header because the Ethernet
header is not pulled by the second nsh_gso_segment().
(b)
While restoring skb->{mac_header,network_header} in 8 & 9,
nsh_gso_segment() does not assume that the data in the linear
buffer is shifted.
However, udp6_ufo_fragment() could shift the data and change
skb->mac_header accordingly as demonstrated by syzbot.
If this happens, even the restored skb->mac_header points to
the middle of the outer header.
It seems nsh_gso_segment() has never worked with outer headers so far.
At the end of nsh_gso_segment(), the outer header must be restored for
the segmented skb, instead of the NSH header.
To do that, let's calculate the outer header position relatively from
the inner header and set skb->{data,mac_header,protocol} properly.
With the current thermal zone locking arrangement in the debugfs code,
user space can open the "mitigations" file for a thermal zone before
the zone's debugfs pointer is set which will result in a NULL pointer
dereference in tze_seq_start().
Moreover, thermal_debug_tz_remove() is not called under the thermal
zone lock, so it can run in parallel with the other functions accessing
the thermal zone's struct thermal_debugfs object. Then, it may clear
tz->debugfs after one of those functions has checked it and the
struct thermal_debugfs object may be freed prematurely.
To address the first problem, pass a pointer to the thermal zone's
struct thermal_debugfs object to debugfs_create_file() in
thermal_debug_tz_add() and make tze_seq_start(), tze_seq_next(),
tze_seq_stop(), and tze_seq_show() retrieve it from s->private
instead of a pointer to the thermal zone object. This will ensure
that tz_debugfs will be valid across the "mitigations" file accesses
until thermal_debugfs_remove_id() called by thermal_debug_tz_remove()
removes that file.
To address the second problem, use tz->lock in thermal_debug_tz_remove()
around the tz->debugfs value check (in case the same thermal zone is
removed at the same time in two different threads) and its reset to NULL.
Fixes: 7ef01f228c9f ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Cc :6.8+ <stable@vger.kernel.org> # 6.8+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because thermal_debug_tz_remove() does not free all memory allocated for
thermal zone diagnostics, some of that memory becomes unreachable after
freeing the thermal zone's struct thermal_debugfs object.
Address this by making thermal_debug_tz_remove() free all of the memory
in question.
Fixes: 7ef01f228c9f ("thermal/debugfs: Add thermal debugfs information for mitigation episodes")
Cc :6.8+ <stable@vger.kernel.org> # 6.8+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We try to access count + 1 byte from userspace with memdup_user(buffer,
count + 1). However, the userspace only provides buffer of count bytes and
only these count bytes are verified to be okay to access. To ensure the
copied buffer is NUL terminated, we use memdup_user_nul instead.
Fixes: 3a2eb515d136 ("octeontx2-af: Fix an off by one in rvu_dbg_qsize_write()") Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com> Link: https://lore.kernel.org/r/20240424-fix-oob-read-v2-6-f1f1b53a10f4@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, we allocate a nbytes-sized kernel buffer and copy nbytes from
userspace to that buffer. Later, we use sscanf on this buffer but we don't
ensure that the string is terminated inside the buffer, this can lead to
OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
Currently, we allocate a count-sized kernel buffer and copy count bytes
from userspace to that buffer. Later, we use sscanf on this buffer but we
don't ensure that the string is terminated inside the buffer, this can lead
to OOB read when using sscanf. Fix this issue by using memdup_user_nul
instead of memdup_user.
Commit 50e782a86c98 ("efi/unaccepted: Fix soft lockups caused by
parallel memory acceptance") has released the spinlock so other CPUs can
do memory acceptance in parallel and not triggers softlockup on other
CPUs.
However the softlock up was intermittent shown up if the memory of the
TD guest is large, and the timeout of softlockup is set to 1 second:
When the local irq is enabled at the end of accept_memory(), the
softlockup detects that the watchdog on single CPU has not been fed for
a while. That is to say, even other CPUs will not be blocked by
spinlock, the current CPU might be stunk with local irq disabled for a
while, which hurts not only nmi watchdog but also softlockup.
Chao Gao pointed out that the memory accept could be time costly and
there was similar report before. Thus to avoid any softlocup detection
during this stage, give the softlockup a flag to skip the timeout check
at the end of accept_memory(), by invoking touch_softlockup_watchdog().
When redirecting a packet using XDP, the bpf_redirect_map() helper will set
up the redirect destination information in struct bpf_redirect_info (using
the __bpf_xdp_redirect_map() helper function), and the xdp_do_redirect()
function will read this information after the XDP program returns and pass
the frame on to the right redirect destination.
When using the BPF_F_BROADCAST flag to do multicast redirect to a whole
map, __bpf_xdp_redirect_map() sets the 'map' pointer in struct
bpf_redirect_info to point to the destination map to be broadcast. And
xdp_do_redirect() reacts to the value of this map pointer to decide whether
it's dealing with a broadcast or a single-value redirect. However, if the
destination map is being destroyed before xdp_do_redirect() is called, the
map pointer will be cleared out (by bpf_clear_redirect_map()) without
waiting for any XDP programs to stop running. This causes xdp_do_redirect()
to think that the redirect was to a single target, but the target pointer
is also NULL (since broadcast redirects don't have a single target), so
this causes a crash when a NULL pointer is passed to dev_map_enqueue().
To fix this, change xdp_do_redirect() to react directly to the presence of
the BPF_F_BROADCAST flag in the 'flags' value in struct bpf_redirect_info
to disambiguate between a single-target and a broadcast redirect. And only
read the 'map' pointer if the broadcast flag is set, aborting if that has
been cleared out in the meantime. This prevents the crash, while keeping
the atomic (cmpxchg-based) clearing of the map pointer itself, and without
adding any more checks in the non-broadcast fast path.
Fixes: e624d4ed4aa8 ("xdp: Extend xdp_redirect_map with broadcast support") Reported-and-tested-by: syzbot+af9492708df9797198d6@syzkaller.appspotmail.com Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com> Acked-by: Stanislav Fomichev <sdf@google.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/20240418071840.156411-1-toke@redhat.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current implementation of the mov instruction with sign extension has the
following problems:
1. It clobbers the source register if it is not stacked because it
sign extends the source and then moves it to the destination.
2. If the dst_reg is stacked, the current code doesn't write the value
back in case of 64-bit mov.
3. There is room for improvement by emitting fewer instructions.
The steps for fixing this and the instructions emitted by the JIT are explained
below with examples in all combinations:
Case A: offset == 32:
=====================
Case A.1: src and dst are stacked registers:
--------------------------------------------
1. Load src_lo into tmp_lo
2. Store tmp_lo into dst_lo
3. Sign extend tmp_lo into tmp_hi
4. Store tmp_hi to dst_hi
Example: r3 = (s32)r3
r3 is a stacked register
ldr r6, [r11, #-16] // Load r3_lo into tmp_lo
// str to dst_lo is not emitted because src_lo == dst_lo
asr r7, r6, #31 // Sign extend tmp_lo into tmp_hi
str r7, [r11, #-12] // Store tmp_hi into r3_hi
Case A.2: src is stacked but dst is not:
----------------------------------------
1. Load src_lo into dst_lo
2. Sign extend dst_lo into dst_hi
Example: r6 = (s32)r3
r6 maps to {ARM_R5, ARM_R4} and r3 is stacked
ldr r4, [r11, #-16] // Load r3_lo into r6_lo
asr r5, r4, #31 // Sign extend r6_lo into r6_hi
Case A.3: src is not stacked but dst is stacked:
------------------------------------------------
1. Store src_lo into dst_lo
2. Sign extend src_lo into tmp_hi
3. Store tmp_hi to dst_hi
Example: r3 = (s32)r6
r3 is stacked and r6 maps to {ARM_R5, ARM_R4}
str r4, [r11, #-16] // Store r6_lo to r3_lo
asr r7, r4, #31 // Sign extend r6_lo into tmp_hi
str r7, [r11, #-12] // Store tmp_hi to dest_hi
Case A.4: Both src and dst are not stacked:
-------------------------------------------
1. Mov src_lo into dst_lo
2. Sign extend src_lo into dst_hi
Example: (bf) r6 = (s32)r6
r6 maps to {ARM_R5, ARM_R4}
// Mov not emitted because dst == src
asr r5, r4, #31 // Sign extend r6_lo into r6_hi
Case B: offset != 32:
=====================
Case B.1: src and dst are stacked registers:
--------------------------------------------
1. Load src_lo into tmp_lo
2. Sign extend tmp_lo according to offset.
3. Store tmp_lo into dst_lo
4. Sign extend tmp_lo into tmp_hi
5. Store tmp_hi to dst_hi
Example: r9 = (s8)r3
r9 and r3 are both stacked registers
ldr r6, [r11, #-16] // Load r3_lo into tmp_lo
lsl r6, r6, #24 // Sign extend tmp_lo
asr r6, r6, #24 // ..
str r6, [r11, #-56] // Store tmp_lo to r9_lo
asr r7, r6, #31 // Sign extend tmp_lo to tmp_hi
str r7, [r11, #-52] // Store tmp_hi to r9_hi
Case B.2: src is stacked but dst is not:
----------------------------------------
1. Load src_lo into dst_lo
2. Sign extend dst_lo according to offset.
3. Sign extend tmp_lo into dst_hi
Example: r6 = (s8)r3
r6 maps to {ARM_R5, ARM_R4} and r3 is stacked
ldr r4, [r11, #-16] // Load r3_lo to r6_lo
lsl r4, r4, #24 // Sign extend r6_lo
asr r4, r4, #24 // ..
asr r5, r4, #31 // Sign extend r6_lo into r6_hi
Case B.3: src is not stacked but dst is stacked:
------------------------------------------------
1. Sign extend src_lo into tmp_lo according to offset.
2. Store tmp_lo into dst_lo.
3. Sign extend src_lo into tmp_hi.
4. Store tmp_hi to dst_hi.
Example: r3 = (s8)r1
r3 is stacked and r1 maps to {ARM_R3, ARM_R2}
lsl r6, r2, #24 // Sign extend r1_lo to tmp_lo
asr r6, r6, #24 // ..
str r6, [r11, #-16] // Store tmp_lo to r3_lo
asr r7, r6, #31 // Sign extend tmp_lo to tmp_hi
str r7, [r11, #-12] // Store tmp_hi to r3_hi
Case B.4: Both src and dst are not stacked:
-------------------------------------------
1. Sign extend src_lo into dst_lo according to offset.
2. Sign extend dst_lo into dst_hi.
Example: r6 = (s8)r1
r6 maps to {ARM_R5, ARM_R4} and r1 maps to {ARM_R3, ARM_R2}
lsl r4, r2, #24 // Sign extend r1_lo to r6_lo
asr r4, r4, #24 // ..
asr r5, r4, #31 // Sign extend r6_lo to r6_hi
Fixes: fc832653fa0d ("arm32, bpf: add support for sign-extension mov instruction") Reported-by: syzbot+186522670e6722692d86@syzkaller.appspotmail.com Signed-off-by: Puranjay Mohan <puranjay@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Closes: https://lore.kernel.org/all/000000000000e9a8d80615163f2a@google.com Link: https://lore.kernel.org/bpf/20240419182832.27707-1-puranjay@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
The function __storage_key_init_range() expects the end address to be
the first byte outside the range to be initialized. I.e. end - start
should be the size of the area to be initialized.
The current code works because __storage_key_init_range() will still loop
over every page in the range, but it is slower than using sske_frame().
When creating controls attached to widgets, there are a lot of rules if
they get their name prefixed with widget name or not. Due to that
controls ended up with weirdly looking names like "ssp0_fe DSP Volume",
while topology set it to "DSP Volume".
Fix this by setting no_wname_in_kcontrol_name to true in avs topology
widgets which disables unwanted behaviour.
When __bpf_prog_enter() returns zero, the s1 register is not set to zero,
resulting in incorrect runtime stats. Fix it by setting s1 immediately upon
the return of __bpf_prog_enter().
Fixes: 49b5e77ae3e2 ("riscv, bpf: Add bpf trampoline support for RV64") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Pu Lehui <pulehui@huawei.com> Acked-by: Björn Töpel <bjorn@kernel.org> Link: https://lore.kernel.org/bpf/20240416064208.2919073-3-xukuohai@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to the reading of FIFO during the dump of data registers in
debugfs, if SPI transmission is in progress, it will be affected
and may result in transmission failure. Therefore, the dump
interface of data registers in debugfs is removed.
Fixes: 2b2142f247eb ("spi: hisi-kunpeng: Add debugfs support") Signed-off-by: Devyn Liu <liudingyuan@huawei.com> Reviewed-by: Jay Fang <f.fangjian@huawei.com> Link: https://lore.kernel.org/r/20240416015839.3323398-1-liudingyuan@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The version format string in the AXI SPI Engine driver was probably
intended to print the version number in the same format as the DT
compatible string (e.g. 1.00.a). However, the version just uses
semantic versioning so formatting the patch number as a character
is not correct and would result in printing control characters for
patch numbers less than 32.
This avoid duplicating the same macros in multiple drivers by reusing
the common AXI macros for the version register.
Signed-off-by: David Lechner <dlechner@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20240202213132.3863124-2-dlechner@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 0064db9ce4aa ("spi: axi-spi-engine: fix version format string") Signed-off-by: Sasha Levin <sashal@kernel.org>
Long ago a map file descriptor in a pseudo ldimm64 instruction could
only be present as an immediate value insn[0].imm, and thus this value
was used in a verbose verifier message printed when the file descriptor
wasn't valid. Since addition of BPF_PSEUDO_MAP_IDX_VALUE/BPF_PSEUDO_MAP_IDX
the insn[0].imm field can also contain an index pointing to the file
descriptor in the attr.fd_array array. However, if the file descriptor
is invalid, the verifier still prints the verbose message containing
value of insn[0].imm. Patch the verifier message to always print the
actual file descriptor value.
Fixes: 387544bfa291 ("bpf: Introduce fd_idx") Signed-off-by: Anton Protopopov <aspsk@isovalent.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20240412141100.3562942-1-aspsk@isovalent.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit cd6f2a2e6346 ("ASoC: SOF: Intel: Set the default firmware
library path for IPC4") added the default_lib_path field for all
platforms, but this was missed when LunarLake was later introduced.
Fixes: 64a63d9914a5 ("ASoC: SOF: Intel: LNL: Add support for Lunarlake platform") Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Link: https://msgid.link/r/20240408194147.28919-2-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a regmap_read_bypassed() to allow reads from the hardware registers
while the regmap is in cache-only mode.
A typical use for this is to keep the cache in cache-only mode until
the hardware has reached a valid state, but one or more status registers
must be polled to determine when this state is reached.
For example, firmware download on the cs35l56 can take several seconds if
there are multiple amps sharing limited bus bandwidth. This is too long
to block in probe() so it is done as a background task. The device must
be soft-reset to reboot the firmware and during this time the registers are
not accessible, so the cache should be in cache-only. But the driver must
poll a register to detect when reboot has completed.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 8a731fd37f8b ("ASoC: cs35l56: Move utility functions to shared file") Link: https://msgid.link/r/20240408101803.43183-2-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
value changed: 0xffffffff83d7feb0 -> 0x0000000000000000
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 10713 Comm: syz-executor.4 Tainted: G W 6.8.0-syzkaller-08951-gfe46a7dd189e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 02/29/2024
Prior to this, commit 4cd12c6065df ("bpf, sockmap: Fix NULL pointer
dereference in sk_psock_verdict_data_ready()") fixed one NULL pointer
similarly due to no protection of saved_data_ready. Here is another
different caller causing the same issue because of the same reason. So
we should protect it with sk_callback_lock read lock because the writer
side in the sk_psock_drop() uses "write_lock_bh(&sk->sk_callback_lock);".
To avoid errors that could happen in future, I move those two pairs of
lock into the sk_psock_data_ready(), which is suggested by John Fastabend.
Turns out that due to CONFIG_DEBUG_INFO_BTF_MODULES not having an
explicitly specified "menu item name" in Kconfig, it's basically
impossible to turn it off (see [0]).
This patch fixes the issue by defining menu name for
CONFIG_DEBUG_INFO_BTF_MODULES, which makes it actually adjustable
and independent of CONFIG_DEBUG_INFO_BTF, in the sense that one can
have DEBUG_INFO_BTF=y and DEBUG_INFO_BTF_MODULES=n.
The devm_regulator_get_enable_optional() should be a 'call and forget'
API, meaning, when it is used to enable the regulators, the API does not
provide a handle to do any further control of the regulators. It gives
no real benefit to return an error from the stub if CONFIG_REGULATOR is
not set.
On the contrary, returning an error is causing problems to drivers when
hardware is such it works out just fine with no regulator control.
Returning an error forces drivers to specifically handle the case where
CONFIG_REGULATOR is not set, making the mere existence of the stub
questionalble.
Change the stub implementation for the
devm_regulator_get_enable_optional() to return Ok so drivers do not
separately handle the case where the CONFIG_REGULATOR is not set.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Fixes: da279e6965b3 ("regulator: Add devm helpers for get and enable") Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/ZiedtOE00Zozd3XO@fedora Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devm_regulator_get_enable() should be a 'call and forget' API,
meaning, when it is used to enable the regulators, the API does not
provide a handle to do any further control of the regulators. It gives
no real benefit to return an error from the stub if CONFIG_REGULATOR is
not set.
On the contrary, returning and error is causing problems to drivers when
hardware is such it works out just fine with no regulator control.
Returning an error forces drivers to specifically handle the case where
CONFIG_REGULATOR is not set, making the mere existence of the stub
questionalble. Furthermore, the stub of the regulator_enable() seems to
be returning Ok.
Change the stub implementation for the devm_regulator_get_enable() to
return Ok so drivers do not separately handle the case where the
CONFIG_REGULATOR is not set.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com> Reported-by: Aleksander Mazur <deweloper@wp.pl> Suggested-by: Guenter Roeck <linux@roeck-us.net> Fixes: da279e6965b3 ("regulator: Add devm helpers for get and enable") Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/ZiYF6d1V1vSPcsJS@drtxq0yyyyyyyyyyyyyby-3.rev.dnainternet.fi Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MT6360 regulator binding, the example in the MT6360 mfd binding, and
the devicetree users of those bindings are rightfully declaring MT6360
regulator subnodes with non-capital names, and luckily without using the
deprecated regulator-compatible property.
With this driver declaring capitalized BUCKx/LDOx as of_match string for
the node names, obviously no regulator gets probed: fix that by changing
the MT6360_REGULATOR_DESC macro to add a "match" parameter which gets
assigned to the of_match.
Fixes: d321571d5e4c ("regulator: mt6360: Add support for MT6360 regulator") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://msgid.link/r/20240409144438.410060-1-angelogioacchino.delregno@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Includes:
. CB_GETATTR proc for nfs4_cb_procedures[]
. XDR encoding and decoding function for CB_GETATTR request/reply
. add nfs4_cb_fattr to nfs4_delegation for sending CB_GETATTR
and store file attributes from client's reply.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: 18180a4550d0 ("NFSD: Fix nfsd4_encode_fattr4() crasher") Signed-off-by: Sasha Levin <sashal@kernel.org>
We have a global set of counters that we modify for all of the nfsd
operations, but now that we're exposing these stats across all network
namespaces we need to make the stats also be per-network namespace. We
already have some caching stats that are per-network namespace, so move
these definitions into the same counter and then adjust all the helpers
and users of these stats to provide the appropriate nfsd_net struct so
that the stats are maintained for the per-network namespace objects.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: 18180a4550d0 ("NFSD: Fix nfsd4_encode_fattr4() crasher") Signed-off-by: Sasha Levin <sashal@kernel.org>
We are running nfsd servers inside of containers with their own network
namespace, and we want to monitor these services using the stats found
in /proc. However these are not exposed in the proc inside of the
container, so we have to bind mount the host /proc into our containers
to get at this information.
Separate out the stat counters init and the proc registration, and move
the proc registration into the pernet operations entry and exit points
so that these stats can be exposed inside of network namespaces.
This is an intermediate step, this just exposes the global counters in
the network namespace. Subsequent patches will move these counters into
the per-network namespace container.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: 18180a4550d0 ("NFSD: Fix nfsd4_encode_fattr4() crasher") Signed-off-by: Sasha Levin <sashal@kernel.org>
We're going to merge the stats all into per network namespace in
subsequent patches, rename these nn counters to be consistent with the
rest of the stats.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Stable-dep-of: 18180a4550d0 ("NFSD: Fix nfsd4_encode_fattr4() crasher") Signed-off-by: Sasha Levin <sashal@kernel.org>
If we fail to allocate propname buffer, we need to drop the reference
count we just took. Because the pinctrl_dt_free_maps() includes the
droping operation, here we call it directly.
The of_match shall correspond to the name of the regulator subnode,
or the deprecated `regulator-compatible` property must be used:
failing to do so, the regulator won't probe (and the driver will
as well not probe).
Since the devicetree binding for this driver is actually correct
and wants DTs to use the "usb-otg-vbus-regulator" subnode name,
fix this driver by aligning the `of_match` string to what the DT
binding wants.
Fixes: 0402e8ebb8b8 ("power: supply: mt6360_charger: add MT6360 charger support") Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Link: https://lore.kernel.org/r/20240410084405.1389378-1-angelogioacchino.delregno@collabora.com Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For all the "score" pin-groups all the intel_pingroup-s to select
the non GPIO function are re-used for byt_score_gpio_groups[].
But this is incorrect since a pin-group includes the mode setting,
which for the non GPIO functions generally is 1, where as to select
the GPIO function mode must be set to 0.
So the GPIO function needs separate intel_pingroup-s with their own mode
value of 0.
Add a new PIN_GROUP_GPIO macro which adds a foo_gpio entry to each
pin-group defined this way and update byt_score_gpio_groups[] to point
to the new foo_gpio entries.
The "sus" usb_oc_grp usb_ulpi_grp and pcu_spi_grp pin-groups are special
because these have a non 0 mode value to select the GPIO functions and
these already have matching foo_gpio pin-groups, leave these are unchanged.
The pmu_clk "sus" groups added in commit 2f46d7f7e959 ("pinctrl: baytrail:
Add pinconf group + function for the pmu_clk") do need to use the new
PIN_GROUP_GPIO macro.
Fixes: 2f46d7f7e959 ("pinctrl: baytrail: Add pinconf group + function for the pmu_clk") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzkaller reported a warning [0] triggered while destroying immature
netns.
rpc_proc_register() was called in init_nfs_fs(), but its error
has been ignored since at least the initial commit 1da177e4c3f4
("Linux-2.6.12-rc2").
Recently, commit d47151b79e32 ("nfs: expose /proc/net/sunrpc/nfs
in net namespaces") converted the procfs to per-netns and made
the problem more visible.
Even when rpc_proc_register() fails, nfs_net_init() could succeed,
and thus nfs_net_exit() will be called while destroying the netns.
Then, remove_proc_entry() will be called for non-existing proc
directory and trigger the warning below.
Let's handle the error of rpc_proc_register() properly in nfs_net_init().
Now that we're exposing the rpc stats on a per-network namespace basis,
move this struct into struct nfs_net and use that to make sure only the
per-network namespace stats are exposed.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be29f ("nfs: Handle error of rpc_proc_register() in nfs_net_init().") Signed-off-by: Sasha Levin <sashal@kernel.org>
We're using nfs mounts inside of containers in production and noticed
that the nfs stats are not exposed in /proc. This is a problem for us
as we use these stats for monitoring, and have to do this awkward bind
mount from the main host into the container in order to get to these
states.
Add the rpc_proc_register call to the pernet operations entry and exit
points so these stats can be exposed inside of network namespaces.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be29f ("nfs: Handle error of rpc_proc_register() in nfs_net_init().") Signed-off-by: Sasha Levin <sashal@kernel.org>
We want to be able to have our rpc stats handled in a per network
namespace manner, so add an option to rpc_create_args to specify a
different rpc_stats struct instead of using the one on the rpc_program.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Stable-dep-of: 24457f1be29f ("nfs: Handle error of rpc_proc_register() in nfs_net_init().") Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a misinterpretation of some of the PIN_CONFIG_* options in this
driver library. PIN_CONFIG_OUTPUT_ENABLE should refer to a buffer or
switch in the output direction of the electrical path. The MediaTek
hardware does not have such a thing. The driver incorrectly maps this
option to the GPIO function's direction.
Likewise, PIN_CONFIG_INPUT_ENABLE should refer to a buffer or switch in
the input direction. The hardware does have such a mechanism, and is
mapped to the IES bit. The driver however sets the direction in addition
to the IES bit, which is incorrect. On readback, the IES bit isn't even
considered.
Ironically, the driver does not support readback for PIN_CONFIG_OUTPUT,
while its readback of PIN_CONFIG_{INPUT,OUTPUT}_ENABLE is what it should
be doing for PIN_CONFIG_OUTPUT.
Rework support for these three options, so that PIN_CONFIG_OUTPUT_ENABLE
is completely removed, PIN_CONFIG_INPUT_ENABLE is only linked to the IES
bit, and PIN_CONFIG_OUTPUT is linked to the GPIO function's direction
and output level.
Fixes: 805250982bb5 ("pinctrl: mediatek: add pinctrl-paris that implements the vendor dt-bindings") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20240327091336.3434141-3-wenst@chromium.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the generic pin config library, readback of some options are handled
differently compared to the setting of those options: the argument value
is used to convey enable/disable of an option in the set path, but
success or -EINVAL is used to convey if an option is enabled or disabled
in the debugfs readback path.
PIN_CONFIG_INPUT_SCHMITT_ENABLE is one such option. Fix the readback of
the option in the mediatek-paris library, so that the debugfs dump is
not showing "input schmitt enabled" for pins that don't have it enabled.
The "pctldev" struct is allocated in devm_pinctrl_register_and_init().
It's a devm_ managed pointer that is freed by devm_pinctrl_dev_release(),
so freeing it in pinctrl_enable() will lead to a double free.
The devm_pinctrl_dev_release() function frees the pindescs and destroys
the mutex as well.
The register offset to disable the internal pull-down of GPIOR~T is 0x630
instead of 0x620, as specified in the Ast2600 datasheet v15
The datasheet can download from the official Aspeed website.
Fixes: 15711ba6ff19 ("pinctrl: aspeed-g6: Add AST2600 pinconf support") Reported-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Message-ID: <20240313092809.2596644-1-billy_tsai@aspeedtech.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The `module!` macro creates glue code that are called by C to initialize
the Rust modules using the `Module::init` function. Part of this glue
code are the local functions `__init` and `__exit` that are used to
initialize/destroy the Rust module.
These functions are safe and also visible to the Rust mod in which the
`module!` macro is invoked. This means that they can be called by other
safe Rust code. But since they contain `unsafe` blocks that rely on only
being called at the right time, this is a soundness issue.
Wrap these generated functions inside of two private modules, this
guarantees that the public functions cannot be called from the outside.
Make the safe functions `unsafe` and add SAFETY comments.
Cc: stable@vger.kernel.org Reported-by: Björn Roy Baron <bjorn3_gh@protonmail.com> Closes: https://github.com/Rust-for-Linux/linux/issues/629 Fixes: 1fbde52bde73 ("rust: add `macros` crate") Signed-off-by: Benno Lossin <benno.lossin@proton.me> Reviewed-by: Wedson Almeida Filho <walmeida@microsoft.com> Link: https://lore.kernel.org/r/20240401185222.12015-1-benno.lossin@proton.me
[ Moved `THIS_MODULE` out of the private-in-private modules since it
should remain public, as Dirk Behme noticed [1]. Capitalized comments,
avoided newline in non-list SAFETY comments and reworded to add
Reported-by and newline. ] Link: https://rust-for-linux.zulipchat.com/#narrow/stream/291565-Help/topic/x/near/433512583 Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently Rust kernel modules have their init code placed in the `.text`
section of the .ko file. I don't think this causes any real problems
for Rust modules as long as all code called during initialization lives
in `.text`.
However, if a Rust `init_module()` function (that lives in `.text`)
calls a function marked with `__init` (in C) or
`#[link_section = ".init.text"]` (in Rust), then a warning is
generated by modpost because that function lives in `.init.text`.
For example:
I ran into this while experimenting with converting the bcachefs kernel
module from C to Rust. The module's `init()`, written in Rust, calls C
functions like `bch2_vfs_init()` which are placed in `.init.text`.
This patch places the macro-generated `init_module()` Rust function in
the `.init.text` section. It also marks `init_module()` as unsafe--now
it may not be called after module initialization completes because it
may be freed already.
Note that this is not enough on its own to actually get all the module
initialization code in that section. The module author must still add
the `#[link_section = ".init.text"]` attribute to the Rust `init()` in
the `impl kernel::Module` block in order to then call `__init`
functions. However, this patch enables module authors do so, when
previously it would not be possible (without warnings).
Signed-off-by: Thomas Bertschinger <tahbertschinger@gmail.com> Reviewed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com> Reviewed-by: Alice Ryhl <aliceryhl@google.com> Link: https://lore.kernel.org/r/20240206153806.567055-1-tahbertschinger@gmail.com
[ Reworded title to add prefix. ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Stable-dep-of: 7044dcff8301 ("rust: macros: fix soundness issue in `module!` macro") Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following error caused by hci_conn being freed while
hcy_acl_create_conn_sync is pending:
==================================================================
BUG: KASAN: slab-use-after-free in hci_acl_create_conn_sync+0xa7/0x2e0
Write of size 2 at addr ffff888002ae0036 by task kworker/u3:0/848
Fixes: 45340097ce6e ("Bluetooth: hci_conn: Only do ACL connections sequentially") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
