Chris Blake [Mon, 24 Oct 2016 19:05:54 +0000 (14:05 -0500)]
ar71xx: add mac partition to the MR12/MR16
On the stock Meraki Firmare for the MR12/MR16, a chunk of SPI space
after u-boot-env is used to store the boards Mac address. Sadly as this
was removed on any device already on OpenWRT/LEDE, moving forward a new,
64k partition named "mac" will be used to store the mac address for the
device (which is the minimum size). This allows users to properly set
the correct MAC, without editing the ART partition (which holds the same
MAC for all devices).
The reason the space is taken from kernel instead of rootfs is currently
kernels are only 1.3MB, so that way we can leave the current rootfs
space alone for users who fully utilize the available storage space.
Once this partition is added to a device, you can set your MAC doing the
following:
Chris Blake [Mon, 24 Oct 2016 19:05:53 +0000 (14:05 -0500)]
ar71xx: Move MR12 & MR16 from legacy to generic
This moves the Meraki MR12 and Meraki MR16 to the new generic target.
Tested and verified working on both devices.
Note that kernel/rootfs images are still generated. This is because they
are used for the inital flashing process due to the fun pace at which
UBoot erases/writes to SPI.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Paul Wassi [Sun, 23 Oct 2016 12:21:22 +0000 (14:21 +0200)]
kirkwood: Add RTC driver to kernel for working hctosys
Build the RTC driver into the kernel, (and remove the optional module), in order
to make hctosys working. (Currently the module is loaded after hctosys has failed previously)
Jo-Philipp Wich [Tue, 25 Oct 2016 14:36:47 +0000 (16:36 +0200)]
uhttpd: fix handling of special "/" prefix when matching handlers
The special prefix of "/" should match any url by definition but the final
assertion which ensures that the matched prefix ends in '\0' or '/' is causing
matches against the "/" prefix to fail.
Update to current HEAD in order to fix this particular case.
Stijn Tintel [Mon, 24 Oct 2016 02:08:07 +0000 (05:08 +0300)]
kernel: add fix for CVE-2016-5195
Add fix for CVE-2016-5195 to kernel 3.18 and 4.1.
Kernel 4.4 is already fixed since version 4.4.26 which was committed in 32c28a78f798dffb983a7f00342b471e5e4ac177.
Patches taken from Sasha Levin's linux-stable git tree:
http://git.kernel.org/cgit/linux/kernel/git/sashal/linux-stable.git/
Rafał Miłecki [Mon, 24 Oct 2016 15:03:48 +0000 (17:03 +0200)]
brcm47xx: bump kernel to 4.4
Kernel 4.4 was ready for brcm47xx for almost a year now but I kept
postponing the bump due to problems with Linksys WRT300N v1.0. OpenWrt
and LEDE with 4.4 were hanging at the booting with the:
> Starting program at 0x80001000
(the last CFE message).
This was a permanent state, "make distclean" wasn't helping, I spent
hours debugging this and I was reliably reproducing the issue every
time. I also reported it on linux-mips ML in the thread:
> BCM4704 stopped booting with 4.4 (due to vmlinux size?)
After ~month I started working on WRT300N again. I got hangs as expected
every time I switched from 4.1 to 4.4. I started experimenting with:
1) TRX content (I tried dropping rootfs partition)
2) BZ_TEXT_START of lzma-loader
3) Flashing other variants of image: lzma compressed kernel (without a
loader), gzip compressed one, uncompressed one.
At some point I got rootfs-less image booting and after that I couldn't
reproduce problem anymore, even with a complete firmware. It seems like
hardware was in some locked/unstable state that got magically fixed.
I have LEDE working now, tested it even with "make distclean", it seems
we can bump kernel now. I'll keep testing it on WRT300N for some time.
Rafał Miłecki [Wed, 19 Oct 2016 11:05:53 +0000 (13:05 +0200)]
base-files: add ucidef_set_led_usbport for full usbport support
This helper allows using usbport trigger directly. It requires usbport
compatible syntax and supports specifying multiple USB ports, e.g.:
ucidef_set_led_usbport "usb" "USB" "devicename:colour:function" "usb1-port1" "usb2-port1"
This adds a proper object to the board.json, e.g.
"usb": {
"name": "USB",
"type": "usbport",
"sysfs": "devicename:colour:function",
"ports": [
"usb1-port1",
"usb2-port1"
]
}
and supports translating it into uci section.
Hannu Nyman [Fri, 14 Oct 2016 08:09:47 +0000 (11:09 +0300)]
busybox: adjust download mirror
* Adjust download locations:
- use https as busybox.net permanently redirects http to https
- gentoo mirror has neither 1.25.0 nor 1.25.1 available, so drop it
in favor of buildroot.net that has 1.25.1
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Jo-Philipp Wich [Fri, 21 Oct 2016 10:21:40 +0000 (12:21 +0200)]
sdk: predefine SOURCE_DATE_EPOCH
When building packages within the SDK, there is no Git revision history
available so prepopulate SOURCE_DATE_EPOCH in version.mk, similar to
how we handle REVISION already.
Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Mathias Kresin [Mon, 17 Oct 2016 18:25:53 +0000 (20:25 +0200)]
lantiq: fix thermal sensors driver
Read the temperature including the decimale place from the CGU_GPHY1_CR
register.
Decrement the temperature read from the register by 38.0 degree celsius.
The temperature range of the sensor is -38.0 to +154 °C and the register
value 0 is equal to -38.0 °C. This fixes the report of unrealistic
temperatures as seen on all tested boards.
Give the SoC a few milliseconds to get the first temperature value. On
some rare occasions there is no temperature value in the register when
read the first time after activation. This leads to a reported
temperature of -38.0 °C on boot.
Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check
to make sure the driver doesn't load on v1.1 vr9 SoCs.
Mathias Kresin [Sun, 2 Oct 2016 09:10:02 +0000 (11:10 +0200)]
lantiq: rework VG3503J image
Use the new image build code and remove the lzma loader. The lzma
loader was used to cheat the signature validation of the bootloader and
I found another way to do this.
To migrate boards already using LEDE/OpenWrt to the new image the
following steps need to be done once:
The image uses the uImage firmware splitter now instead of hardcoded
kernel and rootfs partitions. The firmware partition size was extended
to use flash space that was reserved for partitions required only by
the ECI firmware.
Due to the changes an upgrade to a later LEDE revision from a running
LEDE is supported now.
A default switch config was added and the device uses the same MAC
addresses as the ECI firmware now instead of the same for all VG3503J.
Ben Greear [Mon, 17 Oct 2016 21:23:01 +0000 (14:23 -0700)]
Latest ath10k CT 988X firmware (beta-18).
* Backport much of the 10.2 firmware features from upstream QCA driver.
This includes ANI support, adaptive CCA, tx-hang workarounds,
and lots of other things.
Not all of this may be enabled at this point, and more code waits to
be backported as time and motivation allows.
* Fix some rate-control issues where ath10k in station mode (at least), would
sometimes get stuck at low rates. This appeared to be a probe related
state machine issue in the firmware, so I added some timeout logic to kick
the state machine if it gets stuck. This signicantly improves throughput
tests with many stations.
* Support configuring WMI WD timeout using SET_SPECIAL API.
* Properly configure the rx-mask on bootup to work around problem found
by Mr. Kazior. This should remove the need to add the driver hack he
posted.
* Allow configuring pdev failed-retry threshold. This is how many consecutive
tx failures the firmware will allow before resetting the wifi chip (not a full
firmware crash).
Signed-off-by: Ben Greear <greearb@candelatech.com>
Ben Greear [Mon, 17 Oct 2016 20:59:05 +0000 (13:59 -0700)]
ath10k-ct: Update to latest 4.7 CT ath10k driver.
Adds Sebastian's 160Mhz support (un-tested), remove DMA32 change that
broke some x86 systems, allow setting 10.1 CT firmware keepalive watchdog
timeout, support QCA 9887 hardware, and some other tweaks.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Rafał Miłecki [Tue, 4 Oct 2016 10:32:13 +0000 (12:32 +0200)]
kernel: add package for usbport LED trigger
This is upstream alternative for LEDE's ledtrig-usbdev. It's main
advantages are:
1) Support for assigning more than 1 USB port to the LED
2) Setting proper state when activating with device already connected
3) FWIW it's an upstream driver
Felix Fietkau [Mon, 17 Oct 2016 09:16:30 +0000 (11:16 +0200)]
iperf: used an updated renamed tarball instead of main upstream URL
iperf upstream added some bugfixes to the already released 2.0.9 version
without changing the filename. This conflicts with old mirrored files
and the hash that we previously used.
To avoid conflict, use a renamed tarball from mirror2.openwrt.org
containing the new upstream changes
ar71xx: set EU region code for TP-Link TL-WA901ND v4
There is no US firmware for the TL-WA901ND v4 yet, so we'll just
unconditionally set the EU region for now.
This makes LEDE flashable on these devices again. The format of the region
string is slightly different from the one used on the Archer C7 that is
generated by mktplinkfw (the second half of the region string is missing),
but it's similar enough to make it work.
Hauke Mehrtens [Sat, 15 Oct 2016 15:56:23 +0000 (17:56 +0200)]
procd: update sha256sum
Commit f5c741b5e02 updated procd to a more recent version, but did not
change the hash of the tar. Update it to the one matching the file on
the download servers.
build: copy contents of 'src' folder to build dirs (if present)
The normal Prepare step for a build is unpack, apply patches.
But for certain packages, patches contain whole files, which
would be nice to have separately and copied over as a last step
in the Prepare phase.
We need it for some other packages + patches, but I think
the 'hostapd' package can be used as a test for this.
As a quick note:
the reason the condition is being evaluated as
`[ ! -d ./src/ ] || $(CP) ./src/* $(HOST_BUILD_DIR)`
and not with
`[ -d ./src/ ] && $(CP) ./src/* $(HOST_BUILD_DIR)`
is that the latter would translate in a build failure if the `src`
folder is not present (the exit code would be 1).
The first one, succeeds for both cases (if `src` present or not).
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Dirk Neukirchen [Wed, 12 Oct 2016 12:07:44 +0000 (14:07 +0200)]
uboot-ar71xx: make reproducible
OpenWrt uses ancient u-boot thats not reproducible.
There are multiple upstream changes that introduce
reproducible builds like: 859e92b775fd8ebcfacc591eaf621b677c95b6f7
(not used here - the CMD_DATE/TIMESTAMP functionality
seems to be disabled by config)
projects / thirdparty / openwrt.git / log
