We should reset mstat->airtime_ac along with clear up the entries in the
hardware WLAN table for the Rx and Rx accumulative airtime. Otherwsie, the
value msta->airtime_ac - [tx, rx]_last may be a negative and that is not
the actual airtime the device took in the last run.
Reported-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
mhi_alloc_controller() allocates a memory space for mhi_ctrl. When gets
some error, mhi_ctrl should be freed with mhi_free_controller(). But
when ath11k_mhi_read_addr_from_dt() fails, the function returns without
calling mhi_free_controller(), which will lead to a memory leak.
We can fix it by calling mhi_free_controller() when
ath11k_mhi_read_addr_from_dt() fails.
By using a ratio of delay to poll_enabled_time that is not integer
time_remaining underflows and does not exit the loop as expected.
As delay could be derived from DT and poll_enabled_time is defined
in the driver this can easily happen.
Use a signed iterator to make sure that the loop exits once
the remaining time is negative.
HarrrisonPeak, CyclonePeak, SnowFieldPeak and SandyPeak controllers
are marked to support HCI_QUIRK_LE_STATES.
Signed-off-by: Kiran K <kiran.k@intel.com> Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During stress tests with adding VF to namespace and changing vf's
trust there was a race between iavf_reset_task and iavf_close.
Sometimes when IAVF_FLAG_AQ_DISABLE_QUEUES from iavf_close was sent
to PF after reset and before IAVF_AQ_GET_CONFIG was sent then PF
returns error IAVF_NOT_SUPPORTED to disable queues request and
following requests. There is need to get_config before other
aq_required will be send but iavf_close clears all flags, if
get_config was not sent before iavf_close, then it will not be send
at all.
In case when IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS was sent before
IAVF_FLAG_AQ_DISABLE_QUEUES then there was rtnl_lock deadlock
between iavf_close and iavf_adminq_task until iavf_close timeouts
and disable queues was sent after iavf_close ends.
There was also a problem with sending delete/add filters.
Sometimes when filters was not yet added to PF and in
iavf_close all filters was set to remove there might be a try
to remove nonexistent filters on PF.
Add aq_required_tmp to save aq_required flags and send them after
disable_queues will be handled. Clear flags given to iavf_down
different than IAVF_FLAG_AQ_GET_CONFIG as this flag is necessary
to sent other aq_required. Remove some flags that we don't
want to send as we are in iavf_close and we want to disable
interface. Remove filters which was not yet sent and send del
filters flags only when there are filters to remove.
Signed-off-by: Michal Jaron <michalx.jaron@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the system shuts down, SMMU driver will be stopped and
will not assist in IOVA translations. SMMU driver expects all
of its consumers to shutdown before shutting down itself.
WCN6750 being one of the consumer device should not perform any
DMA operations after the SMMU has shutdown which will otherwise
result in SMMU faults.
SMMU driver will call the shutdown() callback of all its
consumer devices and the consumers shall stop further DMA
activity after the invocation of their respective shutdown()
callbacks.
Register the shutdown() callback to the platform core for WCN6750.
Change will not impact other AHB ath11k devices.
Currently if ipcomp_alloc_scratches() fails to allocate memory
ipcomp_scratches holds obsolete address. So when we try to free the
percpu scratches using ipcomp_free_scratches() it tries to vfree non
existent vm area. Described below:
static void * __percpu *ipcomp_alloc_scratches(void)
{
...
scratches = alloc_percpu(void *);
if (!scratches)
return NULL;
ipcomp_scratches does not know about this allocation failure.
Therefore holding the old obsolete address.
...
}
The IP_UNICAST_IF socket option is used to set the outgoing interface
for outbound packets.
The IP_UNICAST_IF socket option was added as it was needed by the
Wine project, since no other existing option (SO_BINDTODEVICE socket
option, IP_PKTINFO socket option or the bind function) provided the
needed characteristics needed by the IP_UNICAST_IF socket option. [1]
The IP_UNICAST_IF socket option works well for unconnected sockets,
that is, the interface specified by the IP_UNICAST_IF socket option
is taken into consideration in the route lookup process when a packet
is being sent. However, for connected sockets, the outbound interface
is chosen when connecting the socket, and in the route lookup process
which is done when a packet is being sent, the interface specified by
the IP_UNICAST_IF socket option is being ignored.
This inconsistent behavior was reported and discussed in an issue
opened on systemd's GitHub project [2]. Also, a bug report was
submitted in the kernel's bugzilla [3].
To understand the problem in more detail, we can look at what happens
for UDP packets over IPv4 (The same analysis was done separately in
the referenced systemd issue).
When a UDP packet is sent the udp_sendmsg function gets called and
the following happens:
1. The oif member of the struct ipcm_cookie ipc (which stores the
output interface of the packet) is initialized by the ipcm_init_sk
function to inet->sk.sk_bound_dev_if (the device set by the
SO_BINDTODEVICE socket option).
2. If the IP_PKTINFO socket option was set, the oif member gets
overridden by the call to the ip_cmsg_send function.
3. If no output interface was selected yet, the interface specified
by the IP_UNICAST_IF socket option is used.
4. If the socket is connected and no destination address is
specified in the send function, the struct ipcm_cookie ipc is not
taken into consideration and the cached route, that was calculated in
the connect function is being used.
Thus, for a connected socket, the IP_UNICAST_IF sockopt isn't taken
into consideration.
This patch corrects the behavior of the IP_UNICAST_IF socket option
for connect()ed sockets by taking into consideration the
IP_UNICAST_IF sockopt when connecting the socket.
In order to avoid reconnecting the socket, this option is still
ignored when applied on an already connected socket until connect()
is called again by the Richard Gobert.
Change the __ip4_datagram_connect function, which is called during
socket connection, to take into consideration the interface set by
the IP_UNICAST_IF socket option, in a similar way to what is done in
the udp_sendmsg function.
The RX and TX byte/packet statistics in this driver could be overflowed
relatively quickly on a 32-bit platform. Switch these stats to use the
u64_stats infrastructure to avoid this.
The APIC supports two modes, legacy APIC (or xAPIC), and Extended APIC
(or x2APIC). X2APIC mode is mostly compatible with legacy APIC, but
it disables the memory-mapped APIC interface in favor of one that uses
MSRs. The APIC mode is controlled by the EXT bit in the APIC MSR.
The MMIO/xAPIC interface has some problems, most notably the APIC LEAK
[1]. This bug allows an attacker to use the APIC MMIO interface to
extract data from the SGX enclave.
Introduce support for a new feature that will allow the BIOS to lock
the APIC in x2APIC mode. If the APIC is locked in x2APIC mode and the
kernel tries to disable the APIC or revert to legacy APIC mode a GP
fault will occur.
Introduce support for a new MSR (IA32_XAPIC_DISABLE_STATUS) and handle
the new locked mode when the LEGACY_XAPIC_DISABLED bit is set by
preventing the kernel from trying to disable the x2APIC.
On platforms with the IA32_XAPIC_DISABLE_STATUS MSR, if SGX or TDX are
enabled the LEGACY_XAPIC_DISABLED will be set by the BIOS. If
legacy APIC is required, then it SGX and TDX need to be disabled in the
BIOS.
[1]: https://aepicleak.com/aepicleak.pdf
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Tested-by: Neelima Krishnan <neelima.krishnan@intel.com> Link: https://lkml.kernel.org/r/20220816231943.1152579-1-daniel.sneddon@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
As we are now enabling full end-to-end flow control to the Thunderbolt
networking driver, in order for it to work properly on second generation
Thunderbolt hardware (Falcon Ridge), we need to add back the workaround
that was removed with commit 53f13319d131 ("thunderbolt: Get rid of E2E
workaround"). However, this time we only apply it for Falcon Ridge
controllers as a form of an additional quirk. For non-Falcon Ridge this
does nothing.
While there fix a typo 'reqister' -> 'register' in the comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol.
When memory poison consumption machine checks fire, MCE notifier
handlers like nfit_handle_mce() record the impacted physical address
range which is reported by the hardware in the MCi_MISC MSR. The error
information includes data about blast radius, i.e. how many cachelines
did the hardware determine are impacted. A recent change
7917f9cdb503 ("acpi/nfit: rely on mce->misc to determine poison granularity")
updated nfit_handle_mce() to stop hard coding the blast radius value of
1 cacheline, and instead rely on the blast radius reported in 'struct
mce' which can be up to 4K (64 cachelines).
It turns out that apei_mce_report_mem_error() had a similar problem in
that it hard coded a blast radius of 4K rather than reading the blast
radius from the error information. Fix apei_mce_report_mem_error() to
convey the proper poison granularity.
tcp_md5sig_pool_populated can be read while another thread
changes its value.
The race has no consequence because allocations
are protected with tcp_md5sig_mutex.
This patch adds READ_ONCE() and WRITE_ONCE() to document
the race and silence KCSAN.
Reported-by: Abhishek Shah <abhishek.shah@columbia.edu> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently queue_userspace_packet will call kfree_skb for all frames,
whether or not an error occurred. This can result in a single dropped
frame being reported as multiple drops in dropwatch. This functions
caller may also call kfree_skb in case of an error. This patch will
consume the skbs instead and allow caller's to use kfree_skb.
Frames sent to userspace can be reported as dropped in
ovs_dp_process_packet, however, if they are dropped in the netlink code
then netlink_attachskb will report the same frame as dropped.
This patch checks for error codes which indicate that the frame has
already been freed.
On the CPSW and ICSS peripherals, there is a possibility that the MDIO
interface returns corrupt data on MDIO reads or writes incorrect data
on MDIO writes. There is also a possibility for the MDIO interface to
become unavailable until the next peripheral reset.
The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.
More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf
Add implementation to disable MDIO state machine, configure MDIO in manual
mode and achieve MDIO read and writes via MDIO Bitbanging
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com> Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the user changes the number of queues via ethtool, the driver
allocates new rings. This allocation did not initialize tx_tstamps. This
results in the tx_tstamps field being zero (due to kcalloc allocation), and
would result in a NULL pointer dereference when attempting a transmit
timestamp on the new ring.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When bpftool is linked against libcap, the library runs a "constructor"
function to compute the number of capabilities of the running kernel
[0], at the beginning of the execution of the program. As part of this,
it performs multiple calls to prctl(). Some of these may fail, and set
errno to a non-zero value:
# strace -e prctl ./bpftool version
prctl(PR_CAPBSET_READ, CAP_MAC_OVERRIDE) = 1
prctl(PR_CAPBSET_READ, 0x30 /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, CAP_CHECKPOINT_RESTORE) = 1
prctl(PR_CAPBSET_READ, 0x2c /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, 0x2a /* CAP_??? */) = -1 EINVAL (Invalid argument)
prctl(PR_CAPBSET_READ, 0x29 /* CAP_??? */) = -1 EINVAL (Invalid argument)
** fprintf added at the top of main(): we have errno == 1
./bpftool v7.0.0
using libbpf v1.0
features: libbfd, libbpf_strict, skeletons
+++ exited with 0 +++
This has been addressed in libcap 2.63 [1], but until this version is
available everywhere, we can fix it on bpftool side.
Let's clean errno at the beginning of the main() function, to make sure
that these checks do not interfere with the batch mode, where we error
out if errno is set after a bpftool command.
Currently host can send two WMI commands at once. There is possibility to
cause SMMU issues or corruption, if host wants to initiate 2 DMA
transfers, it is possible when copy complete interrupt for first DMA
reaches host, CE has already updated SRRI (Source ring read index) for
both DMA transfers and is in the middle of 2nd DMA. Host uses SRRI
(Source ring read index) to interpret how many DMA’s have been completed
and tries to unmap/free both the DMA entries. Hence now it is limiting to
one.Because CE is still in the middle of 2nd DMA which can cause these
issues when handling two DMA transfers.
This change will not impact other targets, as it is only for WCN3990.
Use-after-free occurred when the laundromat tried to free expired
cpntf_state entry on the s2s_cp_stateids list after inter-server
copy completed. The sc_cp_list that the expired copy state was
inserted on was already freed.
When COPY completes, the Linux client normally sends LOCKU(lock_state x),
FREE_STATEID(lock_state x) and CLOSE(open_state y) to the source server.
The nfs4_put_stid call from nfsd4_free_stateid cleans up the copy state
from the s2s_cp_stateids list before freeing the lock state's stid.
However, sometimes the CLOSE was sent before the FREE_STATEID request.
When this happens, the nfsd4_close_open_stateid call from nfsd4_close
frees all lock states on its st_locks list without cleaning up the copy
state on the sc_cp_list list. When the time the FREE_STATEID arrives the
server returns BAD_STATEID since the lock state was freed. This causes
the use-after-free error to occur when the laundromat tries to free
the expired cpntf_state.
This patch adds a call to nfs4_free_cpntf_statelist in
nfsd4_close_open_stateid to clean up the copy state before calling
free_ol_stateid_reaplist to free the lock state's stid on the reaplist.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This was discussed with Chuck as part of this patch set. Returning
nfserr_resource was decided to not be the best error message here, and
he suggested changing to nfserr_serverfault instead.
Clang produces a false positive when building with CONFIG_FORTIFY_SOURCE=y
and CONFIG_UBSAN_BOUNDS=y when operating on an array with a dynamic
offset. Work around this by using a direct assignment of an empty
instance. Avoids this warning:
../include/linux/fortify-string.h:309:4: warning: call to __write_overflow_field declared with 'warn
ing' attribute: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wat
tribute-warning]
__write_overflow_field(p_size_field, size);
^
which was isolated to the memset() call in xen_load_idt().
Note that this looks very much like another bug that was worked around:
https://github.com/ClangBuiltLinux/linux/issues/1592
Cc: Juergen Gross <jgross@suse.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: x86@kernel.org Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: xen-devel@lists.xenproject.org Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lore.kernel.org/lkml/41527d69-e8ab-3f86-ff37-6b298c01d5bc@oracle.com Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dell Inspiron 14 2-in-1 has two ACPI nodes under GPP1 both with _ADR of
0, both without _HID. It's ambiguous which the kernel should take, but
it seems to take "DEV0". Unfortunately "DEV0" is missing the device
property `StorageD3Enable` which is present on "NVME".
To avoid this causing problems for suspend, add a quirk for this system
to behave like `StorageD3Enable` property was found.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216440 Reported-and-tested-by: Luya Tshimbalanga <luya@fedoraproject.org> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .data.rel.ro.local section has the same semantics as .data.rel.ro
here, so include it in the .rodata section of the decompressor.
Additionally since the .printk_index section isn't usable outside of
the core kernel, discard it in the decompressor. Avoids these warnings:
arm-linux-gnueabi-ld: warning: orphan section `.data.rel.ro.local' from `arch/arm/boot/compressed/fdt_rw.o' being placed in section `.data.rel.ro.local'
arm-linux-gnueabi-ld: warning: orphan section `.printk_index' from `arch/arm/boot/compressed/fdt_rw.o' being placed in section `.printk_index'
Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/linux-mm/202209080545.qMIVj7YM-lkp@intel.com Cc: Russell King <linux@armlinux.org.uk> Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CPU 0 is offline and intel_powerclamp is used to inject
idle, it generates kernel BUG:
BUG: using smp_processor_id() in preemptible [00000000] code: bash/15687
caller is debug_smp_processor_id+0x17/0x20
CPU: 4 PID: 15687 Comm: bash Not tainted 5.19.0-rc7+ #57
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x63
dump_stack+0x10/0x16
check_preemption_disabled+0xdd/0xe0
debug_smp_processor_id+0x17/0x20
powerclamp_set_cur_state+0x7f/0xf9 [intel_powerclamp]
...
...
Here CPU 0 is the control CPU by default and changed to the current CPU,
if CPU 0 offlined. This check has to be performed under cpus_read_lock(),
hence the above warning.
Use get_cpu() instead of smp_processor_id() to avoid this BUG.
When value < time_unit, the parameter of ilog2() will be zero and
the return value is -1. u64(-1) is too large for shift exponent
and then will trigger shift-out-of-bounds:
shift exponent 18446744073709551615 is too large for 32-bit type 'int'
Call Trace:
rapl_compute_time_window_core
rapl_write_data_raw
set_time_window
store_constraint_time_window_us
Signed-off-by: Chao Qin <chao.qin@intel.com> Acked-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang is especially sensitive about argument type matching when using
__overloaded functions (like memcmp(), etc). Help it see that function
pointers are just "void *". Avoids this error:
arch/mips/bcm47xx/prom.c:89:8: error: no matching function for call to 'memcmp'
if (!memcmp(prom_init, prom_init + mem, 32))
^~~~~~
include/linux/string.h:156:12: note: candidate function not viable: no known conversion from 'void (void)' to 'const void *' for 1st argument extern int memcmp(const void *,const void *,__kernel_size_t);
Users may disable HWP in firmware, in which case intel_pstate wouldn't load
unless the CPU model is explicitly supported.
Add TIGERLAKE to the list of CPUs that can register intel_pstate while not
advertising the HWP capability. Without this change, an TIGERLAKE in no-HWP
mode could only use the acpi_cpufreq frequency scaling driver.
See also commits: d8de7a44e11f: cpufreq: intel_pstate: Add Skylake servers support fbdc21e9b038: cpufreq: intel_pstate: Add Icelake servers support in no-HWP mode 706c5328851d: cpufreq: intel_pstate: Add Cometlake support in no-HWP mode
Reported by: M. Cargi Ari <cagriari@pm.me> Signed-off-by: Doug Smythies <dsmythies@telus.net> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a Packard Bell Dot SC (Intel Atom N2600 model) there is a FPDT table
which contains invalid physical addresses, with high bits set which fall
outside the range of the CPU-s supported physical address range.
Calling acpi_os_map_memory() on such an invalid phys address leads to
the below WARN_ON in ioremap triggering resulting in an oops/stacktrace.
Add code to verify the physical address before calling acpi_os_map_memory()
to fix / avoid the oops.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With CONFIG_FORTIFY=y and CONFIG_UBSAN_LOCAL_BOUNDS=y enabled, we observe
a runtime panic while running Android's Compatibility Test Suite's (CTS)
android.hardware.input.cts.tests. This is stemming from a strlen()
call in hidinput_allocate().
__compiletime_strlen() is implemented in terms of __builtin_object_size(),
then does an array access to check for NUL-termination. A quirk of
__builtin_object_size() is that for strings whose values are runtime
dependent, __builtin_object_size(str, 1 or 0) returns the maximum size
of possible values when those sizes are determinable at compile time.
Example:
static const char *v = "FOO BAR";
static const char *y = "FOO BA";
unsigned long x (int z) {
// Returns 8, which is:
// max(__builtin_object_size(v, 1), __builtin_object_size(y, 1))
return __builtin_object_size(z ? v : y, 1);
}
So when FORTIFY_SOURCE is enabled, the current implementation of
__compiletime_strlen() will try to access beyond the end of y at runtime
using the size of v. Mixed with UBSAN_LOCAL_BOUNDS we get a fault.
hidinput_allocate() has a local C string whose value is control flow
dependent on a switch statement, so __builtin_object_size(str, 1)
evaluates to the maximum string length, making all other cases fault on
the last character check. hidinput_allocate() could be cleaned up to
avoid runtime calls to strlen() since the local variable can only have
literal values, so there's no benefit to trying to fortify the strlen
call site there.
Perform a __builtin_constant_p() check against index 0 earlier in the
macro to filter out the control-flow-dependant case. Add a KUnit test
for checking the expected behavioral characteristics of FORTIFY_SOURCE
internals.
Toshiba Satellite Z830 needs the quirk video_disable_backlight_sysfs_if
for proper backlight control after suspend/resume cycles.
Toshiba Portege Z830 is simply the same laptop rebranded for certain
markets (I looked through the manual to other language sections to confirm
this) and thus also needs this quirk.
Thanks to Hans de Goede for suggesting this fix.
Link: https://www.spinics.net/lists/platform-driver-x86/msg34394.html Suggested-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Arvid Norlander <lkml@vorpal.se> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Arvid Norlander <lkml@vorpal.se> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the wrong lowest perf value reading which is used for new
des_perf calculation by governor requested, the incorrect min_perf will
get incorrect des_perf to be set , that will cause the system frequency
changing unexpectedly.
Reviewed-by: Huang Rui <ray.huang@amd.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Perry Yuan <Perry.Yuan@amd.com> Signed-off-by: Su Jinzhou <jinzhou.su@amd.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fill_page_cache_func() function allocates couple of pages to store
kvfree_rcu_bulk_data structures. This is a lightweight (GFP_NORETRY)
allocation which can fail under memory pressure. The function will,
however keep retrying even when the previous attempt has failed.
This retrying is in theory correct, but in practice the allocation is
invoked from workqueue context, which means that if the memory reclaim
gets stuck, these retries can hog the worker for quite some time.
Although the workqueues subsystem automatically adjusts concurrency, such
adjustment is not guaranteed to happen until the worker context sleeps.
And the fill_page_cache_func() function's retry loop is not guaranteed
to sleep (see the should_reclaim_retry() function).
And we have seen this function cause workqueue lockups:
Originally, we thought that the root cause of this lockup was several
retries with direct reclaim, but this is not yet confirmed. Furthermore,
we have seen similar lockups without any heavy memory pressure. This
suggests that there are other factors contributing to these lockups.
However, it is not really clear that endless retries are desireable.
So let's make the fill_page_cache_func() function back off after
allocation failure.
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Neeraj Upadhyay <quic_neeraju@quicinc.com> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Lai Jiangshan <jiangshanlai@gmail.com> Cc: Joel Fernandes <joel@joelfernandes.org> Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernels built with PREEMPT_RCU=y and RCU_STRICT_GRACE_PERIOD=y trigger
irq-work from rcu_read_unlock(), and the resulting irq-work handler
invokes rcu_preempt_deferred_qs_handle(). The point of this triggering
is to force grace periods to end quickly in order to give tools like KASAN
a better chance of detecting RCU usage bugs such as leaking RCU-protected
pointers out of an RCU read-side critical section.
However, this irq-work triggering is unconditional. This works, but
there is no point in doing this irq-work unless the current grace period
is waiting on the running CPU or task, which is not the common case.
After all, in the common case there are many rcu_read_unlock() calls
per CPU per grace period.
This commit therefore triggers the irq-work only when the current grace
period is waiting on the running CPU or task.
This change was tested as follows on a four-CPU system:
This procedure produces results in this per-CPU set of files:
/sys/kernel/debug/tracing/trace_stat/function*
Sample output from one of these files is as follows:
Function Hit Time Avg s^2
-------- --- ---- --- ---
rcu_preempt_deferred_qs_handle 838746 182650.3 us 0.217 us 0.004 us
The baseline sum of the "Hit" values (the number of calls to this
function) was 3,319,015. With this commit, that sum was 1,140,359,
for a 2.9x reduction. The worst-case variance across the CPUs was less
than 25%, so this large effect size is statistically significant.
This patch fixes a race between queue_work() in
_dlm_lowcomms_commit_msg() and srcu_read_unlock(). The queue_work() can
take the final reference of a dlm_msg and so msg->idx can contain
garbage which is signaled by the following warning:
I reproduced this warning with dlm_locktorture test which is currently
not upstream. However this patch fix the issue by make a additional
refcount between dlm_lowcomms_new_msg() and dlm_lowcomms_commit_msg().
In case of the race the kref_put() in dlm_lowcomms_commit_msg() will be
the final put.
Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
An instance of Client does not implicitly close /dev/tpm* handle, once it
gets destroyed. Close the file handle in the class destructor
Client.__del__().
Fixes: 6ea3dfe1e0732 ("selftests: add TPM 2.0 tests") Cc: Shuah Khan <shuah@kernel.org> Cc: linux-kselftest@vger.kernel.org Cc: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Stefan Berger <stefanb@linux.ibm.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
f2fs_inode_info.cp_task was introduced for FS_CP_DATA_IO accounting
since commit b0af6d491a6b ("f2fs: add app/fs io stat").
However, cp_task usage coverage has been increased due to below
commits:
commit 040d2bb318d1 ("f2fs: fix to avoid deadloop if data_flush is on")
commit 186857c5a14a ("f2fs: fix potential recursive call when enabling data_flush")
So that, if data_flush mountoption is on, when data flush was
triggered from background, the IO from data flush will be accounted
as checkpoint IO type incorrectly.
In order to fix this issue, this patch splits cp_task into two:
a) cp_task: used for IO accounting
b) wb_task: used to avoid deadlock
Fixes: 040d2bb318d1 ("f2fs: fix to avoid deadloop if data_flush is on") Fixes: 186857c5a14a ("f2fs: fix potential recursive call when enabling data_flush") Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The following scenarios exist.
process A: process B:
->f2fs_drop_extent_tree ->f2fs_update_extent_cache_range
->f2fs_update_extent_tree_range
->write_lock
->set_inode_flag
->is_inode_flag_set
->__free_extent_tree // Shouldn't
// have been
// cleaned up
// here
->write_lock
In this case, the "FI_NO_EXTENT" flag is set between
f2fs_update_extent_tree_range and is_inode_flag_set
by other process. it leads to clearing the whole exten
tree which should not have happened. And we fix it by
move the setting it to the range of write_lock.
If an error is detected as a result of user-space process accessing a
corrupt memory location, the CPU may take an abort. Then the platform
firmware reports kernel via NMI like notifications, e.g. NOTIFY_SEA,
NOTIFY_SOFTWARE_DELEGATED, etc.
For NMI like notifications, commit 7f17b4a121d0 ("ACPI: APEI: Kick the
memory_failure() queue for synchronous errors") keep track of whether
memory_failure() work was queued, and make task_work pending to flush out
the queue so that the work is processed before return to user-space.
The code use init_mm to check whether the error occurs in user space:
if (current->mm != &init_mm)
The condition is always true, becase _nobody_ ever has "init_mm" as a real
VM any more.
In addition to abort, errors can also be signaled as asynchronous
exceptions, such as interrupt and SError. In such case, the interrupted
current process could be any kind of thread. When a kernel thread is
interrupted, the work ghes_kick_task_work deferred to task_work will never
be processed because entry_handler returns to call ret_to_kernel() instead
of ret_to_user(). Consequently, the estatus_node alloced from
ghes_estatus_pool in ghes_in_nmi_queue_one_entry() will not be freed.
After around 200 allocations in our platform, the ghes_estatus_pool will
run of memory and ghes_in_nmi_queue_one_entry() returns ENOMEM. As a
result, the event failed to be processed.
sdei: event 805 on CPU 113 failed with error: -2
Finally, a lot of unhandled events may cause platform firmware to exceed
some threshold and reboot.
The condition should generally just do
if (current->mm)
as described in active_mm.rst documentation.
Then if an asynchronous error is detected when a kernel thread is running,
(e.g. when detected by a background scrubber), do not add task_work to it
as the original patch intends to do.
Fixes: 7f17b4a121d0 ("ACPI: APEI: Kick the memory_failure() queue for synchronous errors") Signed-off-by: Shuai Xue <xueshuai@linux.alibaba.com> Reviewed-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Counterintuitively, mod_timer(..., jiffies + 1) will cause the timer to
fire not in the next jiffy, but in two jiffies. The way to cause
the timer to fire in the next jiffy is with mod_timer(..., jiffies).
Doing so then lets us bump the upper bound back up again.
Fixes: 50ee7529ec45 ("random: try to actively add entropy rather than passively wait for it") Fixes: 829d680e82a9 ("random: cap jitter samples per bit to factor of HZ") Cc: Dominik Brodowski <linux@dominikbrodowski.net> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Sultan Alsawaf <sultan@kerneltoast.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "ntohl(ucode->code_length) * 2" multiplication can have an
integer overflow.
Fixes: 9e2c7d99941d ("crypto: cavium - Add Support for Octeon-tx CPT Engine") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "code_length * 2" can overflow. The round_up(ucode_size, 16) +
sizeof() expression can overflow too. Prevent these overflows.
Fixes: d9110b0b01ff ("crypto: marvell - add support for OCTEON TX CPT engine") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 7b4537199a4a ("kbuild: link symbol CRCs at final link,
removing CONFIG_MODULE_REL_CRCS"), the module versioning on the
(non-upstreamed-yet) kvx Linux port is broken due to unexpected padding
for __crc_* symbols. The kvx GCC adds padding so u32 gets 8-byte
alignment instead of 4.
I do not know if this happens for upstream architectures in general,
but any compiler has the freedom to insert padding for faster access.
Use the inline assembler to directly specify the wanted data layout.
This is how we previously did before the breakage.
When receiving some signal, GNU Make automatically deletes the target if
it has already been changed by the interrupted recipe.
If the target is possibly incomplete due to interruption, it must be
deleted so that it will be remade from scratch on the next run of make.
Otherwise, the target would remain corrupted permanently because its
timestamp had already been updated.
Thanks to this behavior of Make, you can stop the build any time by
pressing Ctrl-C, and just run 'make' to resume it.
Kbuild also relies on this feature, but it is equivalently important
for any build systems that make decisions based on timestamps (if you
want to support Ctrl-C reliably).
However, this does not always work as claimed; Make immediately dies
with Ctrl-C if its stderr goes into a pipe.
$ make 2>&1 | cat # hit Ctrl-C
echo hello > foo
sleep 3
^C$ # 'foo' is often left-over
The reason is because SIGINT is sent to the entire process group.
In this example, SIGINT kills 'cat', and 'make' writes the message to
the closed pipe, then dies with SIGPIPE before cleaning the target.
A typical bad scenario (as reported by [1], [2]) is to save build log
by using the 'tee' command:
$ make 2>&1 | tee log
This can be problematic for any build systems based on Make, so I hope
it will be fixed in GNU Make. The maintainer of GNU Make stated this is
a long-standing issue and difficult to fix [3]. It has not been fixed
yet as of writing.
So, we cannot rely on Make cleaning the target. We can do it by
ourselves, in signal traps.
As far as I understand, Make takes care of SIGHUP, SIGINT, SIGQUIT, and
SITERM for the target removal. I added the traps for them, and also for
SIGPIPE just in case cmd_* rule prints something to stdout or stderr
(but I did not observe an actual case where SIGPIPE was triggered).
[Note 1]
The trap handler might be worth explaining.
rm -f $@; trap - $(sig); kill -s $(sig) $$
This lets the shell kill itself by the signal it caught, so the parent
process can tell the child has exited on the signal. Generally, this is
a proper manner for handling signals, in case the calling program (like
Bash) may monitor WIFSIGNALED() and WTERMSIG() for WCE although this may
not be a big deal here because GNU Make handles SIGHUP, SIGINT, SIGQUIT
in WUE and SIGTERM in IUE.
IUE - Immediate Unconditional Exit
WUE - Wait and Unconditional Exit
WCE - Wait and Cooperative Exit
For details, see "Proper handling of SIGINT/SIGQUIT" [4].
[Note 2]
Reverting 392885ee82d3 ("kbuild: let fixdep directly write to .*.cmd
files") would directly address [1], but it only saves if_changed_dep.
As reported in [2], all commands that use redirection can potentially
leave an empty (i.e. broken) target.
[Note 3]
Another (even safer) approach might be to always write to a temporary
file, and rename it to $@ at the end of the recipe.
<command> > $(tmp-target)
mv $(tmp-target) $@
It would require a lot of Makefile changes, and result in ugly code,
so I did not take it.
[Note 4]
A little more thoughts about a pattern rule with multiple targets (or
a grouped target).
%.x %.y: %.z
<recipe>
When interrupted, GNU Make deletes both %.x and %.y, while this solution
only deletes $@. Probably, this is not a big deal. The next run of make
will execute the rule again to create $@ along with the other files.
There is a recursive lock on the cpu_hotplug_lock.
In kernel/trace/trace_osnoise.c:<start/stop>_per_cpu_kthreads:
- start_per_cpu_kthreads calls cpus_read_lock() and if
start_kthreads returns a error it will call stop_per_cpu_kthreads.
- stop_per_cpu_kthreads then calls cpus_read_lock() again causing
deadlock.
Fix this by calling cpus_read_unlock() before calling
stop_per_cpu_kthreads. This behavior can also be seen in commit f46b16520a08 ("trace/hwlat: Implement the per-cpu mode").
This error was noticed during the LTP ftrace-stress-test:
WARNING: possible recursive locking detected
--------------------------------------------
sh/275006 is trying to acquire lock: ffffffffb02f5400 (cpu_hotplug_lock){++++}-{0:0}, at: stop_per_cpu_kthreads
but task is already holding lock: ffffffffb02f5400 (cpu_hotplug_lock){++++}-{0:0}, at: start_per_cpu_kthreads
other info that might help us debug this:
Possible unsafe locking scenario:
For now, this selftest module can only work in x86 because of the
kprobe cmd was fixed use of x86 registers.
This patch adapted to register names under arm and riscv, So that
this module can be worked on those platform.
IOMMU_IOVA is intended to be an optional library for users to select as
and when they desire. Since it can be a module now, this means that
built-in code which has chosen not to select it should not fail to link
if it happens to have selected as a module by someone else. Replace
IS_ENABLED() with IS_REACHABLE() to do the right thing.
CC: Thierry Reding <thierry.reding@gmail.com> Reported-by: John Garry <john.garry@huawei.com> Fixes: 15bbdec3931e ("iommu: Make the iova library a module") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Reviewed-by: Thierry Reding <treding@nvidia.com> Link: https://lore.kernel.org/r/548c2f683ca379aface59639a8f0cccc3a1ac050.1663069227.git.robin.murphy@arm.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error happens while getting the key or session in the
->calc_signature implementations, 0 (success) is returned. Fix it by
returning a proper error code.
Since it seems to be highly unlikely to happen wrap the rc check in
unlikely() too.
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Fixes: 32811d242ff6 ("cifs: Start using per session key for smb2/3 for signature generation") Signed-off-by: Enzo Matsumiya <ematsumiya@suse.de> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit a38b71b0833e ("clocksource/drivers/arm_arch_timer:
Move system register timer programming over to CVAL") moves the
programming of the timers from the countdown timer (TVAL) over
to the comparator (CVAL). This makes it necessary to read the
counter when programming next event. However, the workaround of
Cortex-A73 erratum 858921 does not set the corresponding
set_next_event_phys and set_next_event_virt.
Add the appropriate hooks to apply the erratum mitigation when
programming the next timer event.
Fixes: a38b71b0833e ("clocksource/drivers/arm_arch_timer: Move system register timer programming over to CVAL") Signed-off-by: Kunkun Jiang <jiangkunkun@huawei.com> Acked-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20220914061424.1260-1-jiangkunkun@huawei.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_DMA_API_DEBUG is selected, while running the crypto self
test on the QAT crypto algorithms, the function add_dma_entry() reports
a warning similar to the one below, saying that overlapping mappings
are not supported. This occurs in tests where the input and the output
scatter list point to the same buffers (i.e. two different scatter lists
which point to the same chunks of memory).
The logic that implements the mapping uses the flag DMA_BIDIRECTIONAL
for both the input and the output scatter lists which leads to
overlapped write mappings. These are not supported by the DMA layer.
Fix by specifying the correct DMA transfer directions when mapping
buffers. For in-place operations where the input scatter list
matches the output scatter list, buffers are mapped once with
DMA_BIDIRECTIONAL, otherwise input buffers are mapped using the flag
DMA_TO_DEVICE and output buffers are mapped with DMA_FROM_DEVICE.
Overlapping a read mapping with a write mapping is a valid case in
dma-coherent devices like QAT.
The function that frees and unmaps the buffers, qat_alg_free_bufl()
has been changed accordingly to the changes to the mapping function.
The use of swab() is causing failures in 64-bit arch, as it
translates to __swab64() instead of the intended __swab32().
It eventually causes wrong results in xcbcmac & cmac algo.
Fixes: 78cf1c8bfcb8 ("crypto: inside-secure - Move ipad/opad into safexcel_context") Signed-off-by: Peter Harliman Liem <pliem@maxlinear.com> Acked-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
__dma_async_device_channel_unregister called while 2 clients hold a reference
WARNING: CPU: 15 PID: 1 at drivers/dma/dmaengine.c:1110 __dma_async_device_channel_unregister+0xb7/0xc0
Call dma_release_channel for occupied channles before dma_async_device_unregister.
Fixes: 54cce8ecb925 ("crypto: ccp - ccp_dmaengine_unregister release dma channels") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Koba Ko <koba.ko@canonical.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Changes from v1:
* removed the default implementation from set_pub_key: it is assumed that
an implementation must always have this callback defined as there are
no use case for an algorithm, which doesn't need a public key
Many akcipher implementations (like ECDSA) support only signature
verifications, so they don't have all callbacks defined.
Commit 78a0324f4a53 ("crypto: akcipher - default implementations for
request callbacks") introduced default callbacks for sign/verify
operations, which just return an error code.
However, these are not enough, because before calling sign the caller would
likely call set_priv_key first on the instantiated transform (as the
in-kernel testmgr does). This function does not have a default stub, so the
kernel crashes, when trying to set a private key on an akcipher, which
doesn't support signature generation.
I've noticed this, when trying to add a KAT vector for ECDSA signature to
the testmgr.
With this patch the testmgr returns an error in dmesg (as it should)
instead of crashing the kernel NULL ptr dereference.
1) The "len" variable needs to be checked before the very first write.
Otherwise if omap2_iommu_dump_ctx() with "bytes" less than 32 it is a
buffer overflow.
2) The snprintf() function returns the number of bytes that *would* have
been copied if there were enough space. But we want to know the
number of bytes which were *actually* copied so use scnprintf()
instead.
Previously, update_tasks_cpumask() is not supposed to be called with
top cpuset. With cpuset partition that takes CPUs away from the top
cpuset, adjusting the cpus_mask of the tasks in the top cpuset is
necessary. Percpu kthreads, however, are ignored.
Fixes: ee8dde0cd2ce ("cpuset: Add new v2 cpuset.sched.partition flag") Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Issue:
While servicing interrupt, if the IRQ happens to be because of a SEED_DONE
due to a previous boot stage, you end up completing the completion
prematurely, hence causing kernel to crash while booting.
Fix:
Moving IRQ handler registering after imx_rngc_irq_mask_clear()
Fixes: 1d5449445bd0 (hwrng: mx-rngc - add a driver for Freescale RNGC) Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
cgroup_get_from_path() is not widely used function. Its callers presume
the path is resolved under cgroup namespace. (There is one caller
currently and resolving in init NS won't make harm (netfilter). However,
future users may be subject to different effects when resolving
globally.)
Since, there's currently no use for the global resolution, modify the
existing function to take cgroup NS into account.
Currently the OS continues the PSP initialization when there is a write
failure to the init_ex_file. Therefore, the userspace would be told that
SEV is properly INIT'd even though the psp data file is not updated.
This is problematic because later when asked for the SEV data, the OS
won't be able to provide it.
Fixes: 3d725965f836 ("crypto: ccp - Add SEV_INIT_EX support") Reported-by: Peter Gonda <pgonda@google.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Jacky Li <jackyli@google.com> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The SMCCC_RET_TRNG_NO_ENTROPY switch arm is never used because the
NO_ENTROPY return value is negative and negative values are handled
above the switch by immediately returning.
Fix by handling errors using a default arm in the switch.
Fixes: 0888d04b47a1 ("hwrng: Add Arm SMCCC TRNG based driver") Signed-off-by: James Cowgill <james.cowgill@blaize.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
[17619.659757] BUG: KASAN: global-out-of-bounds in param_get_int+0x34/0x60
[17619.673193] Read of size 4 at addr fffff01332d7ed00 by task read_all/1507958
...
[17619.698934] The buggy address belongs to the variable:
[17619.708371] sgl_sge_nr+0x0/0xffffffffffffa300 [hisi_zip]
There is a mismatch in hisi_zip when get/set the variable sgl_sge_nr.
The type of sgl_sge_nr is u16, and get/set sgl_sge_nr by
param_get/set_int.
Replacing param_get/set_int to param_get/set_ushort can fix this bug.
Fixes: f081fda293ffb ("crypto: hisilicon - add sgl_sge_nr module param for zip") Signed-off-by: Ye Weihua <yeweihua4@huawei.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function of sahara_aes_crypt maybe could be called by function
of crypto_skcipher_encrypt during the rx softirq, so it is not
allowed to use mutex lock.
Generally the hypervisor decides to allocate a window on different
VAS instances. But if user space wishes to allocate on the current VAS
instance where the process is executing, the kernel has to pass
associativity domain IDs to allocate VAS window HCALL.
To determine the associativity domain IDs for the current CPU,
smp_processor_id() is passed to node associativity HCALL which may
return H_P2 (-55) error during DLPAR CPU event. This is because Linux
CPU numbers (smp_processor_id()) are not the same as the hypervisor's
view of CPU numbers.
Fix the issue by passing hard_smp_processor_id() with
VPHN_FLAG_VCPU flag (PAPR 14.11.6.1 H_HOME_NODE_ASSOCIATIVITY).
Fixes: b22f2d88e435 ("powerpc/pseries/vas: Integrate API with open/close windows") Reviewed-by: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Haren Myneni <haren@linux.ibm.com>
[mpe: Update change log to mention Linux vs HV CPU numbers] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/55380253ea0c11341824cd4c0fc6bbcfc5752689.camel@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If prev is based on ftrace, 'ppc_inst_read(prev->ainsn.insn)' will occur
with a null pointer reference. At this point prev->addr will not be a
prefixed instruction, so the check can be skipped.
Check if prev is ftrace-based kprobe before reading 'prev->ainsn.insn'
to fix this problem.
Fixes: b4657f7650ba ("powerpc/kprobes: Don't allow breakpoints on suffixes") Signed-off-by: Li Huafei <lihuafei1@huawei.com>
[mpe: Trim oops] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220923093253.177298-1-lihuafei1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2eb28006431c ("powerpc/e500v2: Add Power ISA properties to comply
with ePAPR 1.1") introduced new include file e500v2_power_isa.dtsi and
should have used it for all e500v2 platforms. But apparently it was used
also for e500v1 platforms mpc8540, mpc8541, mpc8555 and mpc8560.
e500v1 cores compared to e500v2 do not support double precision floating
point SPE instructions. Hence power-isa-sp.fd should not be set on e500v1
platforms, which is in e500v2_power_isa.dtsi include file.
Fix this issue by introducing a new e500v1_power_isa.dtsi include file and
use it in all e500v1 device tree files.
Fixes: 2eb28006431c ("powerpc/e500v2: Add Power ISA properties to comply with ePAPR 1.1") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220902212103.22534-1-pali@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
If a synchronous interrupt (e.g., hash fault) is taken inside an
irqs-disabled region which has MSR[EE]=1, then an asynchronous interrupt
that is PACA_IRQ_MUST_HARD_MASK (e.g., PMI) is taken inside the
synchronous interrupt handler, then the synchronous interrupt will
return with MSR[EE]=1 and the asynchronous interrupt fires again.
If the asynchronous interrupt is a PMI and the original context does not
have PMIs disabled (only Linux IRQs), the asynchronous interrupt will
fire despite having the PMI marked soft pending. This can confuse the
perf code and cause warnings.
This patch changes the interrupt return so that irqs-disabled MSR[EE]=1
contexts will be returned to with MSR[EE]=0 if a PACA_IRQ_MUST_HARD_MASK
interrupt has become pending in the meantime.
Fixes: 4423eb5ae32e ("powerpc/64/interrupt: make normal synchronous interrupts enable MSR[EE] if possible") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220926054305.2671436-4-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This prevents interrupts in early boot (e.g., program check) from
enabling MSR[EE], potentially causing endian mismatch or other
crashes when reporting early boot traps.
Fixes: 4423eb5ae32ec ("powerpc/64/interrupt: make normal synchronous interrupts enable MSR[EE] if possible") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220926054305.2671436-3-npiggin@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Big-endian GENERIC_CPU supports 970, but builds with -mcpu=power5.
POWER5 is ISA v2.02 whereas 970 is v2.01 plus Altivec. 2.02 added
the popcntb instruction which a compiler might use.
As reported[1] by Arnd, the arch-specific fadvise64_64 and fallocate
compatibility handlers assume parameters are passed with 32-bit
big-endian ABI. This affects the assignment of odd-even parameter pairs
to the high or low words of a 64-bit syscall parameter.
Fix fadvise64_64 fallocate compat handlers to correctly swap upper/lower
32 bits conditioned on endianness.
A future patch will replace the arch-specific compat fallocate with an
asm-generic implementation. This patch is intended for ease of
back-port.
Currently, we are using CPU_PM_CPU_IDLE_ENTER_PARAM() for all SBI HSM
suspend types so retentive suspend types are also treated non-retentive
and kernel will do redundant additional work for these states.
The BIT[31] of SBI HSM suspend types allows us to differentiate between
retentive and non-retentive suspend types so we should use this BIT
to call appropriate CPU_PM_CPU_IDLE_ENTER_xyz() macro.
Fixes: 6abf32f1d9c5 ("cpuidle: Add RISC-V SBI CPU idle driver") Signed-off-by: Anup Patel <apatel@ventanamicro.com> Link: https://lore.kernel.org/r/20220718084553.2056169-1-apatel@ventanamicro.com/ Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In fsl_setup_msi_irqs(), use of_node_put() to drop the reference
returned by of_parse_phandle().
Fixes: 895d603f945ba ("powerpc/fsl_msi: add support for the fsl, msi property in PCI nodes") Co-authored-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Liang He <windhl@126.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220704145233.278539-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with a recent version of clang, there are a couple of
errors around the call to module_init():
arch/powerpc/math-emu/math_efp.c:927:1: error: type specifier missing, defaults to 'int'; ISO C99 and later do not support implicit int [-Wimplicit-int]
module_init(spe_mathemu_init);
^
int
arch/powerpc/math-emu/math_efp.c:927:13: error: a parameter list without types is only allowed in a function definition
module_init(spe_mathemu_init);
^
2 errors generated.
module_init() is a macro, which is not getting expanded because module.h
is not included in this file. Add the include so that the macro can
expand properly, clearing up the build failure.
commit db7cfc380900 ("ipc: Free mq_sysctls if ipc namespace creation
failed")
Here's a similar memory leak to the one fixed by the patch above.
retire_mq_sysctls need to be called when init_mqueue_fs fails after
setup_mq_sysctls.
Fixes: dc55e35f9e81 ("ipc: Store mqueue sysctls in the ipc namespace") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Link: https://lkml.kernel.org/r/20220715062301.19311-1-hbh25y@gmail.com Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mailbox offset is not only used for receiving messages, but it is
also used by messages sent to the system controller by Linux that have a
payload, such as the "digital signature service". It is also overloaded
by certain other services (reprogramming of the FPGA fabric, see Link:)
to have a meaning other than the offset the system controller should
read from.
When the driver was written, no such services of the latter type were
in use & those of the former used an offset of zero so this has gone
un-noticed.
The "data" region of the PolarFire SoC's system controller mailbox is
not one continuous register space - the system controller's QSPI sits
between the control and data registers. Split the "data" reg into two
parts: "data" & "control". Optionally get the "data" register address
from the 3rd reg property in the devicetree & fall back to using the
old base + MAILBOX_REG_OFFSET that the current code uses.
pm_runtime_get_sync() will increment pm usage counter.
Forgetting to putting operation will result in reference leak.
Add missing pm_runtime_put_sync in some error paths.
Fixes: 9ac33b0ce81f ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220602030838.52057-1-linmq006@gmail.com Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ti_find_clock_provider(), of_find_node_by_name() will call
of_node_put() for the 'from' argument, possibly putting the node one too
many times. Let's maintain the of_node_get() from the previous search
and only put when we're exiting the function early. This should avoid a
misbalanced reference count on the node.
Fixes: 51f661ef9a10 ("clk: ti: Add ti_find_clock_provider() to use clock-output-names") Signed-off-by: Liang He <windhl@126.com> Link: https://lore.kernel.org/r/20220915031121.4003589-1-windhl@126.com
[sboyd@kernel.org: Rewrite commit text, maintain reference instead of
get again] Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value of bcm2835_clock_rate_from_divisor is always unsigned
and also all caller expect this. So fix the declaration accordingly.
Fixes: 41691b8862e2 ("clk: bcm2835: Add support for programming the audio domain clocks") Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/20220904141037.38816-1-stefan.wahren@i2se.com Reviewed-by: Ivan T. Ivanov <iivanov@suse.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turns out the internal SATA reference clock signal will stay
unavailable for the SATA interface consumer until the buffer on it's way
is ungated. So aside with having the actual clock divider enabled we need
to ungate a buffer placed on the signal way to the SATA controller (most
likely some rudiment from the initial SoC release). Seeing the switch flag
is placed in the same register as the SATA-ref clock divider at a
non-standard ffset, let's implement it as a separate clock controller with
the set-rate propagation to the parental clock divider wrapper. As such
we'll be able to disable/enable and still change the original clock source
rate.
Baikal-T1 CCU reference manual says that both xGMAC reference and xGMAC
PTP clocks are generated by two different wrappers with the same constant
divider thus each producing a 156.25 MHz signal. But for some reason both
of these clock sources are gated by a single switch-flag in the CCU
registers space - CCU_SYS_XGMAC_BASE.BIT(0). In order to make the clocks
handled independently we need to define a shared parental gate so the base
clock signal would be switched off only if both of the child-clocks are
disabled.
Note the ID is intentionally set to -2 since we are going to add a one
more internal clock identifier in the next commit.
Most likely due to copy-paste mistake the divider has been set to 10 while
according to the SoC reference manual it's supposed to be 8 thus having
PTP clock frequency of 156.25 MHz.
We have discovered random glitches during the system boot up procedure.
The problem investigation led us to the weird outcomes: when none of the
Renesas 5P49V6901 ports are explicitly enabled by the kernel driver, the
glitches disappeared. It was a mystery since the SoC external clock
domains were fed with different 5P49V6901 outputs. The driver code didn't
seem like bogus either. We almost despaired to find out a root cause when
the solution has been found for a more modern revision of the chip. It
turned out the 5P49V6901 clock generator stopped its output for a short
period of time during the VC5_OUT_DIV_CONTROL register writing. The same
problem was found for the 5P49V6965 revision of the chip and was
successfully fixed in commit fc336ae622df ("clk: vc5: fix output disabling
when enabling a FOD") by enabling the "bypass_sync" flag hidden inside
"Unused Factory Reserved Register". Even though the 5P49V6901 registers
description and programming guide doesn't provide any intel regarding that
flag, setting it up anyway in the officially unused register completely
eliminated the denoted glitches. Thus let's activate the functionality
submitted in commit fc336ae622df ("clk: vc5: fix output disabling when
enabling a FOD") for the Renesas 5P49V6901 chip too in order to remove the
ports implicit inter-dependency.
Fixes: dbf6b16f5683 ("clk: vc5: Add support for IDT VersaClock 5P49V6901") Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net> Link: https://lore.kernel.org/r/20220929225402.9696-2-Sergey.Semin@baikalelectronics.ru Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
