It appears that not all hardware/firmware implementations support
group key deletion correctly, which can lead to connection hangs
and deauthentication following GTK rekeying (delete and install).
To avoid this issue, instead of attempting to delete the key using
the special WMI_CIPHER_NONE value, we now replace the key with an
invalid (random) value.
This behavior has been observed with WCN39xx chipsets.
snprintf() returns the number of bytes that would have been written, not
the number actually written. Using this for offset tracking can cause
buffer overruns if truncation occurs.
Replace snprintf() with scnprintf() to ensure the offset stays within
bounds.
Since scnprintf() never returns a negative value, and zero is not possible
in this context because 'bytes' starts at 0 and 'size - bytes' is
DEBUG_BUFFER_SIZE in the first call, which is large enough to hold the
string literals used, the return value is always positive. An integer
overflow is also completely out of reach here due to the small and fixed
buffer size. The error check in latency_show_one() is therefore
unnecessary. Remove it and make dmar_latency_snapshot() return void.
Allow mhi_sync_power_up to handle SYS_ERR during power-up, reboot,
or recovery. This is to avoid premature exit when MHI_PM_IN_ERROR_STATE is
observed during above mentioned system states.
To achieve this, treat SYS_ERR as a valid state and let its handler process
the error and queue the next transition to Mission Mode instead of aborting
early.
When a PHY is halted (e.g. `ip link set dev lan2 down`), several
fields in struct phy_device may still reflect the last active
connection. This leads to ethtool showing stale values even though
the link is down.
Reset selected fields in _phy_state_machine() when transitioning
to PHY_HALTED and the link was previously up:
- speed/duplex -> UNKNOWN, but only in autoneg mode (in forced mode
these fields carry configuration, not status)
- master_slave_state -> UNKNOWN if previously supported
- mdix -> INVALID (state only, same meaning as "unknown")
- lp_advertising -> always cleared
The cleanup is skipped if the PHY is in PHY_ERROR state, so the
last values remain available for diagnostics.
kcalloc() may fail. When WS is non-zero and allocation fails, ectx.ws
remains NULL while ectx.ws_size is set, leading to a potential NULL
pointer dereference in atom_get_src_int() when accessing WS entries.
Return -ENOMEM on allocation failure to avoid the NULL dereference.
Signed-off-by: Guangshuo Li <lgs201920130244@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Connect ioctl has the same memory for in and out parameters.
Copy in parameter (client uuid) to the local stack to avoid it be
overwritten by out parameters fill.
The transaction manager initialization in txInit() was not properly
initializing TxBlock[0].waitor waitqueue, causing a crash when
txEnd(0) is called on read-only filesystems.
When a filesystem is mounted read-only, txBegin() returns tid=0 to
indicate no transaction. However, txEnd(0) still gets called and
tries to access TxBlock[0].waitor via tid_to_tblock(0), but this
waitqueue was never initialized because the initialization loop
started at index 1 instead of 0.
This causes a 'non-static key' lockdep warning and system crash:
INFO: trying to register non-static key in txEnd
Fix by ensuring all transaction blocks including TxBlock[0] have
their waitqueues properly initialized during txInit().
Reported-by: syzbot+c4f3462d8b2ad7977bea@syzkaller.appspotmail.com Signed-off-by: Shaurya Rane <ssrane_b23@ee.vjti.ac.in> Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
These older chips now support the fw log traces via backing store
qcaps_v2. No other backing store memory types are supported besides
the fw trace types.
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com> Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Shruti Parab <shruti.parab@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20250917040839.1924698-6-michael.chan@broadcom.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, all master upper netdevices (e.g., bond, VRF) are treated
equally.
When a VRF netdevice is used over an IPoIB netdevice, the expected
netdev resolution is on the lower IPoIB device which has the IP address
assigned to it and not the VRF device.
The rdma_cm module (CMA) tries to match incoming requests to a
particular netdevice. When successful, it also validates that the return
path points to the same device by performing a routing table lookup.
Currently, the former would resolve to the VRF netdevice, while the
latter to the correct lower IPoIB netdevice, leading to failure in
rdma_cm.
Improve this by ignoring the VRF master netdevice, if it exists, and
instead return the lower IPoIB device.
Add READ_ONCE() annotations because np->rxpmtu can be changed
while udpv6_recvmsg() and rawv6_recvmsg() read it.
Since this is a very rarely used feature, and that udpv6_recvmsg()
and rawv6_recvmsg() read np->rxopt anyway, change the test order
so that np->rxpmtu does not need to be in a hot cache line.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com> Link: https://patch.msgid.link/20250916160951.541279-4-edumazet@google.com Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add xhci support for PCI hosts that have zero USB3 ports.
Avoid creating a shared Host Controller Driver (HCD) when there is only
one root hub. Additionally, all references to 'xhci->shared_hcd' are now
checked before use.
Only xhci-pci.c requires modification to accommodate this change, as the
xhci core already supports configurations with zero USB3 ports. This
capability was introduced when xHCI Platform and MediaTek added support
for zero USB3 ports.
Logically before a waiting side which has already timed out turns the
atomic status back to idle, a completing side could still pass atomic
condition and call complete. It will make the following H2C commands,
waiting C2H events, get a completion unexpectedly early. Hence, renew
a completion for each H2C command waiting a C2H event.
The IE length of RTW89_PHYSTS_IE09_FTR_0 is dynamic, need to calculate
more to get it. This IE is not necessary now, disable it to avoid get
wrong IE length to let the parse function check failed.
When we get wrong extent info data, and look up extent_node in rb tree,
it will cause infinite loop (CONFIG_F2FS_CHECK_FS=n). Avoiding this by
return NULL and print some kernel messages in that case.
Allow autosuspend to be used by xhci plat device. For Qualcomm SoCs,
when in host mode, it is intended that the controller goes to suspend
state to save power and wait for interrupts from connected peripheral
to wake it up. This is particularly used in cases where a HID or Audio
device is connected. In such scenarios, the usb controller can enter
auto suspend and resume action after getting interrupts from the
connected device.
The usbmon binary interface currently truncates captures of large
transfers from higher-speed USB devices. Because a single event capture
is limited to one-fifth of the total buffer size, the current maximum
size of a captured URB is around 240 KiB. This is insufficient when
capturing traffic from modern devices that use transfers of several
hundred kilobytes or more, as truncated URBs can make it impossible for
user-space USB analysis tools like Wireshark to properly defragment and
reassemble higher-level protocol packets in the captured data.
The root cause of this issue is the 1200 KiB BUFF_MAX limit, which has
not been changed since the binary interface was introduced in 2006.
To resolve this issue, this patch increases BUFF_MAX to 64 MiB. The
original comment for BUFF_MAX based the limit's calculation on a
saturated 480 Mbit/s bus. Applying the same logic to a modern USB 3.2
Gen 2×2 20 Gbit/s bus (~2500 MB/s over a 20ms window) indicates the
buffer should be at least 50 MB. The new limit of 64 MiB covers that,
plus a little extra for any overhead.
With this change, both users and developers should now be able to debug
and reverse engineer modern USB devices even when running unmodified
distro kernels.
Please note that this change does not affect the default buffer size. A
larger buffer is only allocated when a user explicitly requests it via
the MON_IOCT_RING_SIZE ioctl, so the change to the maximum buffer size
should not unduly increase memory usage for users that don't
deliberately request a larger buffer.
There is a timing race condition when a PRLI may be sent on the wire
before PLOGI_ACC in Point to Point topology. Fix by deferring REG_RPI
mbox completion handling to after PLOGI_ACC's CQE completion. Because
the discovery state machine only sends PRLI after REG_RPI mbox
completion, PRLI is now guaranteed to be sent after PLOGI_ACC.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Message-ID: <20250915180811.137530-8-justintee8345@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
To assist in debugging lpfc_xri_rebalancing driver parameter, a debugfs
entry is used. The debugfs file operations for xri rebalancing have
been previously implemented, but lack definition for its information
buffer size. Similar to other pre-existing debugfs entry buffers,
define LPFC_HDWQINFO_SIZE as 8192 bytes.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Message-ID: <20250915180811.137530-9-justintee8345@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In lpfc_cleanup, there is an extraneous nlp_put for NPIV ports on the
F_Port_Ctrl ndlp object. In cases when an ABTS is issued, the
outstanding kref is needed for when a second XRI_ABORTED CQE is
received. The final kref for the ndlp is designed to be decremented in
lpfc_sli4_els_xri_aborted instead. Also, add a new log message to allow
for future diagnostics when debugging related issues.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Message-ID: <20250915180811.137530-5-justintee8345@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If lpfc_reset_flush_io_context fails to execute, then the wrong return
status code may be passed back to upper layers when issuing a target
reset TMF command. Fix by checking the return status from
lpfc_reset_flush_io_context() first in order to properly return FAILED
or FAST_IO_FAIL.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Message-ID: <20250915180811.137530-7-justintee8345@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The kref for Fabric_DID ndlps is not decremented after repeated FDISC
failures and exhausting maximum allowed retries. This can leave the
ndlp lingering unnecessarily. Add a test and set bit operation for the
NLP_DROPPED flag. If not previously set, then a kref is decremented. The
ndlp is freed when the remaining reference for the completing ELS is
put.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Message-ID: <20250915180811.137530-6-justintee8345@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
lpfc_sli4_queue_setup() does not allocate memory and is used for
submitting CREATE_QUEUE mailbox commands. Thus, if such mailbox
commands fail we should clean up by also freeing the memory allocated
for the queues with lpfc_sli4_queue_destroy(). Change the intended
clean up label for the lpfc_sli4_queue_setup() error case to
out_destroy_queue.
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Message-ID: <20250915180811.137530-4-justintee8345@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some Kioxia UFS 4 devices do not support the qTimestamp attribute. Set
the UFS_DEVICE_QUIRK_NO_TIMESTAMP_SUPPORT for these devices such that no
error messages appear in the kernel log about failures to set the
qTimestamp attribute.
Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Avri Altman <avri.altman@sandisk.com> Tested-by: Nitin Rawat <quic_nitirawa@quicinc.com> # on SM8650-QRD Reviewed-by: Nitin Rawat <quic_nitirawa@quicinc.com> Reviewed-by: Peter Wang <peter.wang@mediatek.com> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Message-ID: <20250909190614.3531435-1-bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The selftests 'make clean' does not clean the net/lib because it only
processes $(TARGETS) and ignores $(INSTALL_DEP_TARGETS). This leaves
compiled objects in net/lib after cleaning, requiring manual cleanup.
Include $(INSTALL_DEP_TARGETS) in clean target to ensure net/lib
dependency is properly cleaned.
Signed-off-by: Nai-Chen Cheng <bleach1827@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Acked-by: Shuah Khan <skhan@linuxfoundation.org> Link: https://patch.msgid.link/20250910-selftests-makefile-clean-v1-1-29e7f496cd87@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Gang submission means that the kernel driver guarantees that multiple
submissions are executed on the HW at the same time on different engines.
Background is that those submissions then depend on each other and each
can't finish stand alone.
SRIOV now uses world switch to preempt submissions on the engines to allow
sharing the HW resources between multiple VFs.
The problem is now that the SRIOV world switch can't know about such inter
dependencies and will cause a timeout if it waits for a partially running
gang submission.
To conclude SRIOV and gang submissions are fundamentally incompatible at
the moment. For now just disable them.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to multiple explosion issues in the early days of the Xe driver,
the GuC load was hacked to never return a failure. That prevented
kernel panics and such initially, but now all it achieves is creating
more confusing errors when the driver tries to submit commands to a
GuC it already knows is not there. So fix that up.
As a stop-gap and to help with debug of load failures due to invalid
GuC init params, a wedge call had been added to the inner GuC load
function. The reason being that it leaves the GuC log accessible via
debugfs. However, for an end user, simply aborting the module load is
much cleaner than wedging and trying to continue. The wedge blocks
user submissions but it seems that various bits of the driver itself
still try to submit to a dead GuC and lots of subsequent errors occur.
And with regards to developers debugging why their particular code
change is being rejected by the GuC, it is trivial to either add the
wedge back in and hack the return code to zero again or to just do a
GuC log dump to dmesg.
v2: Add support for error injection testing and drop the now redundant
wedge call.
In nested arrays don't require that the intermediate attribute
type should be a valid attribute type, it might just be zero
or an incrementing index, it is often not even used.
See include/net/netlink.h about NLA_NESTED_ARRAY:
> The difference to NLA_NESTED is the structure:
> NLA_NESTED has the nested attributes directly inside
> while an array has the nested attributes at another
> level down and the attribute types directly in the
> nesting don't matter.
Example based on include/uapi/linux/wireguard.h:
> WGDEVICE_A_PEERS: NLA_NESTED
> 0: NLA_NESTED
> WGPEER_A_PUBLIC_KEY: NLA_EXACT_LEN, len WG_KEY_LEN
> [..]
> 0: NLA_NESTED
> ...
> ...
Previous the check required that the nested type was valid
in the parent attribute set, which in this case resolves to
WGDEVICE_A_UNSPEC, which is YNL_PT_REJECT, and it took the
early exit and returned YNL_PARSE_CB_ERROR.
This patch renames the old nl_attr_validate() to
__nl_attr_validate(), and creates a new inline function
nl_attr_validate() to mimic the old one.
The new __nl_attr_validate() takes the attribute type as an
argument, so we can use it to validate attributes of a
nested attribute, in the context of the parents attribute
type, which in the above case is generated as:
[WGDEVICE_A_PEERS] = {
.name = "peers",
.type = YNL_PT_NEST,
.nest = &wireguard_wgpeer_nest,
},
__nl_attr_validate() only checks if the attribute length
is plausible for a given attribute type, so the .nest in
the above example is not used.
As the new inline function needs to be defined after
ynl_attr_type(), then the definitions are moved down,
so we avoid a forward declaration of ynl_attr_type().
Some other examples are NL80211_BAND_ATTR_FREQS (nest) and
NL80211_ATTR_SUPPORTED_COMMANDS (u32) both in nl80211-user.c
$ make -C tools/net/ynl/generated nl80211-user.c
Signed-off-by: Asbjørn Sloth Tønnesen <ast@fiberby.net> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Link: https://patch.msgid.link/20250915144301.725949-7-ast@fiberby.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As netif_queue_set_napi checks napi->dev, if it doesn't have it and
it will warn_on and return. So we should use netif_napi_add before
netif_queue_set_napi because netif_napi_add has "napi->dev = dev".
Dell systems utilize an EC-based touchpad emulation when the ACPI
touchpad _DSM is not invoked. This emulation acts as a secondary
master on the I2C bus, designed for scenarios where the I2C touchpad
driver is absent, such as in BIOS menus. Typically, loading the
i2c-hid module triggers the _DSM at initialization, disabling the
EC-based emulation.
However, if the i2c-hid module is missing from the boot kernel
used for hibernation snapshot restoration, the _DSM remains
uncalled, resulting in dual masters on the I2C bus and
subsequent arbitration errors. This issue arises when i2c-hid
resides in the rootfs instead of the kernel or initramfs.
To address this, switch from using the SYSTEM_SLEEP_PM_OPS()
macro to dedicated callbacks, introducing a specific
callback for restoring the S4 image. This callback ensures
the _DSM is invoked.
Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the UFS lane clocks remain enabled even after the link enters
the Hibern8 state and are only disabled during runtime/system
suspend.This patch modifies the behavior to disable the lane clocks
during ufs_qcom_setup_clocks(), which is invoked shortly after the link
enters Hibern8 via gate work.
While hibern8_notify() offers immediate control, toggling clocks on
every transition isn't ideal due to varied contexts like clock scaling.
Since setup_clocks() manages PHY/controller resources and is invoked
soon after Hibern8 entry, it serves as a central and stable point for
clock gating.
Signed-off-by: Palash Kambar <quic_pkambar@quicinc.com> Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Message-ID: <20250909055149.2068737-1-quic_pkambar@quicinc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A lot of modern SoC have the ability to store MAC addresses in their
NVMEM. So extend the generic function device_get_mac_address() to
obtain the MAC address from an nvmem cell named 'mac-address' in
case there is no firmware node which contains the MAC address directly.
Driver authors often forget to add GFP_NOWARN for page allocation
from the datapath. This is annoying to users as OOMs are a fact
of life, and we pretty much expect network Rx to hit page allocation
failures during OOM. Make page pool add GFP_NOWARN for ATOMIC allocations
by default.
Clear EEE runtime flags when the PHY transitions to HALTED or ERROR
and the state machine drops the link. This avoids stale EEE state being
reported via ethtool after the PHY is stopped or hits an error.
This change intentionally only clears software runtime flags and avoids
MDIO accesses in HALTED/ERROR. A follow-up patch will address other
link state variables.
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/20250912132000.1598234-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dml21_map_dc_state_into_dml_display_cfg calls (the call is usually
inlined by the compiler) populate_dml21_surface_config_from_plane_state
and populate_dml21_plane_config_from_plane_state which may use FPU. In
a x86-64 build:
Thus it needs to be guarded with DC_FP_START. But we must note that the
current code quality of the in-kernel FPU use in AMD dml2 is very much
problematic: we are actually calling DC_FP_START in dml21_wrapper.c
here, and this translation unit is built with CC_FLAGS_FPU. Strictly
speaking this does not make any sense: with CC_FLAGS_FPU the compiler is
allowed to generate FPU uses anywhere in the translated code, perhaps
out of the DC_FP_START guard. This problematic pattern also occurs in
at least dml2_wrapper.c, dcn35_fpu.c, and dcn351_fpu.c. Thus we really
need a careful audit and refactor for the in-kernel FPU uses, and this
patch is simply whacking a mole. However per the reporter, whacking
this mole is enough to make a 9060XT "just work."
Reported-by: Asiacn <710187964@qq.com> Closes: https://github.com/loongson-community/discussions/issues/102 Tested-by: Asiacn <710187964@qq.com> Signed-off-by: Xi Ruoyao <xry111@xry111.site> Reviewed-by: Huacai Chen <chenhuacai@loongson.cn> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the EDID has the HDMI bit, we should simply select
the HDMI signal type even on DVI ports.
For reference see, the legacy amdgpu display code:
amdgpu_atombios_encoder_get_encoder_mode
which selects ATOM_ENCODER_MODE_HDMI for the same case.
This commit fixes DVI connectors to work with DVI-D/HDMI
adapters so that they can now produce output over these
connectors for HDMI monitors with higher bandwidth modes.
With this change, even HDMI audio works through DVI.
For testing, I used a CAA-DMDHFD3 DVI-D/HDMI adapter
with the following GPUs:
Tahiti (DCE 6) - DC can now output 4K 30 Hz over DVI
Polaris 10 (DCE 11.2) - DC can now output 4K 60 Hz over DVI
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
DC can turn off the display clock when no displays are connected
or when all displays are off, for reference see:
- dce*_validate_bandwidth
DC also assumes that the DP clock is always on and never powers
it down, for reference see:
- dce110_clock_source_power_down
In case of DCE 6.0 and 6.4, PLL0 is the clock source for both
the engine clock and DP clock, for reference see:
- radeon_atom_pick_pll
- atombios_crtc_set_disp_eng_pll
Therefore, PLL0 should be always kept running on DCE 6.0 and 6.4.
This commit achieves that by ensuring that by setting the display
clock to the corresponding value in low power state instead of
zero.
This fixes a page flip timeout on SI with DC which happens when
all connected displays are blanked.
Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Normally resources are evicted on dGPUs at suspend or hibernate and
on APUs at hibernate. These steps are unnecessary when using the S4
callbacks to put the system into S5.
Cc: AceLan Kao <acelan.kao@canonical.com> Cc: Kai-Heng Feng <kaihengf@nvidia.com> Cc: Mark Pearson <mpearson-lenovo@squebb.ca> Cc: Denis Benato <benato.denis96@gmail.com> Cc: Merthan Karakaş <m3rthn.k@gmail.com> Tested-by: Eric Naim <dnaim@cachyos.org> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why&how]
small error in order of operations in immediateflipbytes
calculation on dml ms side that can result in dml ms
and mp mismatch immediateflip support for a given pipe
and thus an invalid hw state, correct the order to align
with mp.
Reviewed-by: Leo Chen <leo.chen@amd.com> Signed-off-by: Ausef Yousof <Ausef.Yousof@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
fill_stream_properties_from_drm_display_mode() will not configure pixel
encoding to YCBCR422 when the DRM color format supports YCBCR422 but not
YCBCR420 or YCBCR4444. Instead it will fallback to RGB.
[How]
Add support for YCBCR422 in pixel encoding mapping.
Suggested-by: Mauri Carvalho <mcarvalho3@lenovo.com> Reviewed-by: Wayne Lin <wayne.lin@amd.com> Signed-off-by: Mario Limonciello <Mario.Limonciello@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
New sequence from HW for reset and firmware reloading has been
provided that aims to stabilize the reload sequence in the case the
firmware is hung or has outstanding requests.
[How]
Update the sequence to remove the DMUIF reset and the redundant
writes in the release.
Reviewed-by: Sreeja Golui <sreeja.golui@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Ray Wu <ray.wu@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If multiple instances of this driver are instantiated and try to send
concurrently then the single static buffer snd_serial_generic_tx_work()
will cause corruption in the data output.
Move the buffer into the per-instance driver data to avoid this.
Support writing MAC TXD for the AddBA Req. Without this commit, the
start sequence number in AddBA Req will be unexpected value for MT7996
and MT7992. This can result in certain stations (e.g., AX200) dropping
packets, leading to ping failures and degraded connectivity. Ensuring
the correct MAC TXD and TXP helps maintain reliable packet transmission
and prevents interoperability issues with affected stations.
EPCS is not yet ready, so do not claim to support it.
Signed-off-by: Benjamin Lin <benjamin-jw.lin@mediatek.com> Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://patch.msgid.link/20250904-mt7996-mlo-more-fixes-v1-4-89d8fed67f20@kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to hibernation causing a power off and power on,
this modification adds mt7925_pci_restore callback function for kernel.
When hibernation resumes, it calls mt7925_pci_restore to reset the device,
allowing it to return to the state it was in before the power off.
Enable 160MHz beamformee support on mt7922 by updating HE capability
element configuration. Previously, only 160MHz channel width was set,
but beamformee for 160MHz was not properly advertised. This patch
adds BEAMFORMEE_MAX_STS_ABOVE_80MHZ_4 capability to allow devices
to utilize 160MHz BW for beamforming.
Tested by connecting to 160MHz-bandwidth beamforming AP and verified
HE capability.
During recent testing with the netem qdisc to inject delays into TCP
traffic, we observed that our CLS BPF program failed to function correctly
due to incorrect classid retrieval from task_get_classid(). The issue
manifests in the following call stack:
The problem occurs when multiple tasks share a single qdisc. In such cases,
__qdisc_run() may transmit skbs created by different tasks. Consequently,
task_get_classid() retrieves an incorrect classid since it references the
current task's context rather than the skb's originating task.
Given that dev_queue_xmit() always executes with bh disabled, we can use
softirq_count() instead to obtain the correct classid.
The simple steps to reproduce this issue:
1. Add network delay to the network interface:
such as: tc qdisc add dev bond0 root netem delay 1.5ms
2. Build two distinct net_cls cgroups, each with a network-intensive task
3. Initiate parallel TCP streams from both tasks to external servers.
Under this specific condition, the issue reliably occurs. The kernel
eventually dequeues an SKB that originated from Task-A while executing in
the context of Task-B.
It is worth noting that it will change the established behavior for a
slightly different scenario:
<sock S is created by task A>
<class ID for task A is changed>
<skb is created by sock S xmit and classified>
prior to this patch the skb will be classified with the 'new' task A
classid, now with the old/original one. The bpf_get_cgroup_classid_curr()
function is a more appropriate choice for this case.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Thomas Graf <tgraf@suug.ch> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250902062933.30087-1-laoar.shao@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If HW Channel (HWC) is not responding, reduce the waiting time, so further
steps will fail quickly.
This will prevent getting stuck for a long time (30 minutes or more), for
example, during unloading while HWC is not responding.
The calculation formula for nominal bit rate of classical CAN is the same as
that of nominal bit rate of CANFD on the RZ/G3E and R-Car Gen4 SoCs
compared to other SoCs. Update nominal bit rate constants.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://patch.msgid.link/20250908120940.147196-2-biju.das.jz@bp.renesas.com
[mkl: slightly improve wording of commit message] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
during entropy evaluation, if the generated samples fail
any statistical test, then, all of the bits will be discarded,
and a second set of samples will be generated and tested.
the entropy delay interval should be doubled before performing the
retry.
also, ctrlpriv->rng4_sh_init and inst_handles both reads RNG DRNG
status register, but only inst_handles is updated before every retry.
so only check inst_handles and removing ctrlpriv->rng4_sh_init
payload_size field of the request header is incorrectly calculated using
sizeof(req). Since 'req' is a pointer (struct hsti_request *), sizeof(req)
returns the size of the pointer itself (e.g., 8 bytes on a 64-bit system),
rather than the size of the structure it points to. This leads to an
incorrect payload size being sent to the Platform Security Processor (PSP),
potentially causing the HSTI query command to fail.
Fix this by using sizeof(*req) to correctly calculate the size of the
struct hsti_request.
Signed-off-by: Yunseong Kim <ysk@kzalloc.com> Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>> --- Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
dw_pcie_edma_irq_verify() is supposed to verify the eDMA IRQs in devicetree
by fetching them using either 'dma' or 'dmaX' IRQ names. Former is used
when the platform uses a single IRQ for all eDMA channels and latter is
used when the platform uses separate IRQ per channel. But currently,
dw_pcie_edma_irq_verify() bails out early if edma::nr_irqs is 1, i.e., when
a single IRQ is used. This gives an impression that the driver could work
with any single IRQ in devicetree, not necessarily with name 'dma'.
But dw_pcie_edma_irq_vector(), which actually requests the IRQ, does
require the single IRQ to be named as 'dma'. So this creates inconsistency
between dw_pcie_edma_irq_verify() and dw_pcie_edma_irq_vector().
Thus, to fix this inconsistency, make sure dw_pcie_edma_irq_verify() also
verifies the single IRQ name by removing the bail out code.
Fix the issue of max_timeout being calculated larger than actual value.
The calculation result of freq / (S3C2410_WTCON_PRESCALE_MAX + 1) /
S3C2410_WTCON_MAXDIV is smaller than the actual value because the remainder
is discarded during the calculation process. This leads to a larger
calculated value for max_timeout compared to the actual settable value.
To resolve this issue, the order of calculations in the computation process
has been adjusted.
The Asus Z13 folio has a multitouch touchpad that needs to bind
to the hid-multitouch driver in order to work properly. So bind
it to the HID_GROUP_GENERIC group to release the touchpad and
move it to the bottom so that the comment applies to it.
While at it, change the generic KEYBOARD3 name to Z13_FOLIO.
Reviewed-by: Luke D. Jones <luke@ljones.dev> Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
netdev_WARN() uses WARN/WARN_ON to print a backtrace along with
file and line information. In this case, udp_tunnel_nic_register()
returning an error is just a failed operation, not a kernel bug.
udp_tunnel_nic_register() can fail due to a memory allocation
failure (kzalloc() or udp_tunnel_nic_alloc()).
This is a normal runtime error and not a kernel bug.
Replace netdev_WARN() with netdev_warn() accordingly.
Usually the autodefer helpers in lib.sh are expected to be run in context
where success is the expected outcome. However when using them for feature
detection, failure can legitimately occur. But the failed command still
schedules a cleanup, which will likely fail again.
Instead, only schedule deferred cleanup when the positive command succeeds.
This way of organizing the cleanup has the added benefit that now the
return code from these functions reflects whether the command passed.
tcp_recvmsg_dmabuf can export the following errors:
- EFAULT when linear copy fails
- ETOOSMALL when cmsg put fails
- ENODEV if one of the frags is readable
- ENOMEM on xarray failures
But they are all ignored and replaced by EFAULT in the caller
(tcp_recvmsg_locked). Expose real error to the userspace to
add more transparency on what specifically fails.
In non-devmem case (skb_copy_datagram_msg) doing `if (!copied)
copied=-EFAULT` is ok because skb_copy_datagram_msg can return only EFAULT.
Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Mina Almasry <almasrymina@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Stanislav Fomichev <sdf@fomichev.me> Link: https://patch.msgid.link/20250910162429.4127997-1-sdf@fomichev.me Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 8139too is probing and 8139TOO_PIO=y it will call pci_iomap_range()
and from there __pci_ioport_map() for the PCI IO space.
If HAS_IOPORT_MAP=n and NO_GENERIC_PCI_IOPORT_MAP=n, like it is on my
m68k config, __pci_ioport_map() becomes NULL, pci_iomap_range() will
always fail and the driver will complain it couldn't map the PIO space
and return an error.
NO_IOPORT_MAP seems to cover the case where what 8139too is trying
to do cannot ever work so make 8139TOO_PIO depend on being it false
and avoid creating an unusable driver.
All of the x86 KVM guest types (VMX, SEV and TDX) do some special context
tracking when entering guests. This means that the actual guest entry
sequence must be noinstr.
Part of entering a TDX guest is passing a physical address to the TDX
module. Right now, that physical address is stored as a 'struct page'
and converted to a physical address at guest entry. That page=>phys
conversion can be complicated, can vary greatly based on kernel
config, and it is definitely _not_ a noinstr path today.
There have been a number of tinkering approaches to try and fix this
up, but they all fall down due to some part of the page=>phys
conversion infrastructure not being noinstr friendly.
Precalculate the page=>phys conversion and store it in the existing
'tdx_vp' structure. Use the new field at every site that needs a
tdvpr physical address. Remove the now redundant tdx_tdvpr_pa().
Remove the __flatten remnant from the tinkering.
Note that only one user of the new field is actually noinstr. All
others can use page_to_phys(). But, they might as well save the effort
since there is a pre-calculated value sitting there for them.
[ dhansen: rewrite all the text ]
Signed-off-by: Kai Huang <kai.huang@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Kiryl Shutsemau <kas@kernel.org> Tested-by: Farrah Chen <farrah.chen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit b2798ba0b876 ("KVM: X86: Choose qspinlock when dedicated
physical CPUs are available") states that when PV_DEDICATED=1
(vCPU has dedicated pCPU), qspinlock should be preferred regardless of
PV_UNHALT. However, the current implementation doesn't reflect this: when
PV_UNHALT=0, we still use virt_spin_lock() even with dedicated pCPUs.
This is suboptimal because:
1. Native qspinlocks should outperform virt_spin_lock() for dedicated
vCPUs irrespective of HALT exiting
2. virt_spin_lock() should only be preferred when vCPUs may be preempted
(non-dedicated case)
So reorder the PV spinlock checks to:
1. First handle dedicated pCPU case (disable virt_spin_lock_key)
2. Second check single CPU, and nopvspin configuration
3. Only then check PV_UNHALT support
This ensures we always use native qspinlock for dedicated vCPUs, delivering
pretty performance gains at high contention levels.
Signed-off-by: Li RongQing <lirongqing@baidu.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Tested-by: Wangyang Guo <wangyang.guo@intel.com> Link: https://lore.kernel.org/r/20250722110005.4988-1-lirongqing@baidu.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
But the icmp reject 'netdev' family versions will reply to icmp
dst-unreach errors, unlike icmp_send() and icmp6_send() which are used
by the inet family implementation (and internally by the REJECT target).
Check for the icmp(6) type and do not respond if its an unreachable error.
Without this, something like 'ip protocol icmp reject', when used
in a netdev chain attached to 'lo', cause a packet loop.
Same for two hosts that both use such a rule: each error packet
will be replied to.
Such situation persist until the (bogus) rule is amended to ratelimit or
checks the icmp type before the reject statement.
As the inet versions don't do this make the netdev ones follow along.
To ensure the proper functioning of the jump_label test module, this patch
adds support for the R_OR1K_32_PCREL relocation type for any modules. The
implementation calculates the PC-relative offset by subtracting the
instruction location from the target value and stores the result at the
specified location.
The test always returns success even if some tests were modified to
fail. Fix by converting the test to use the appropriate library
functions instead of using its own functions.
Originally, the 'amd_pmf_get_custom_bios_inputs()' function was written
under the assumption that the BIOS would only send a single pending
request for the driver to process. However, following OEM enablement, it
became clear that multiple pending requests for custom BIOS inputs might
be sent at the same time, a scenario that the current code logic does not
support when it comes to handling multiple custom BIOS inputs.
To address this, the code logic needs to be improved to not only manage
multiple simultaneous custom BIOS inputs but also to ensure it is scalable
for future additional inputs.
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com> Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com> Tested-by: Yijun Shen <Yijun.Shen@Dell.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Link: https://patch.msgid.link/20250901110140.2519072-3-Shyam-sundar.S-k@amd.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change "ret" from u8 to int type in redrat3_enable_detector() to store
negative error codes or zero returned by redrat3_send_cmd() and
usb_submit_urb() - this better aligns with the coding standards and
maintains code consistency.
No effect on runtime.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
fcnal-test.sh already includes lib.sh, use relevant helpers
instead of sleeping. Replace sleep after starting nettest
as a server with wait_local_port_listen.
The upstream mesa copy of the GPU regs has shifted more things to reg64
instead of seperate 32b HI/LO reg32's. This works better with the "new-
style" c++ builders that mesa has been migrating to for a6xx+ (to better
handle register shuffling between gens), but it leaves the C builders
with missing _HI/LO builders.
So handle the special case of reg64, automatically generating the
missing _HI/LO builders.
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/673559/ Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver for the Rockchip MIPI CSI-2 DPHY uses GRF register offset
value 0 to sort out undefined registers. However, the RK3588 CSIDPHY GRF
this offset is perfectly fine (in fact, register 0 is the only one in
this register file).
Introduce a boolean variable to indicate valid registers and allow writes
to register 0.
When compiled without CONFIG_VIDEO the architecture specific
implementations of video_is_primary_device() include prototypes and
assume that video-common.c will be linked. Guard against this so that the
fallback inline implementation that returns false will be used when
compiled without CONFIG_VIDEO.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202506221312.49Fy1aNA-lkp@intel.com/ Link: https://lore.kernel.org/r/20250811162606.587759-2-superm1@kernel.org Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Enable support for data lane rates between 80-160 Mbps cdns dphy
as mentioned in TRM [0] by setting the pll_opdiv field to 16.
This change enables lower resolutions like 640x480 at 60Hz.
[0]: https://www.ti.com/lit/zip/spruil1
(Table 12-552. DPHY_TX_PLL_CTRL Register Field Descriptions)
In hidden SSID we have separate BSS entries for the beacon and for the
probe response(s).
The BSS entry time stamps represent the age of the BSS;
when was the last time we heard the BSS.
When we receive a beacon of a hidden SSID it means that we heard that
BSS, so it makes sense to indicate that in the probe response entries.
Do that.
Since commit af153bb63a33 ("vfs: catch invalid modes in may_open()")
requires any inode be one of S_IFDIR/S_IFLNK/S_IFREG/S_IFCHR/S_IFBLK/
S_IFIFO/S_IFSOCK type, use S_IFREG for $Extend records.
projects / thirdparty / kernel / stable.git / log
