x86 Hyper-V used to essentially always overwrite the effective cache type
of guest memory accesses to WB. This was problematic in cases where there
is a physical device assigned to the VM, since that often requires that
the VM should have control over cache types. Thus, on newer Hyper-V since
2018, Hyper-V always honors the VM's cache type, but unexpectedly Linux VM
users start to complain that Linux VM's VRAM becomes very slow, and it
turns out that Linux VM should not map the VRAM uncacheable by ioremap().
Fix this slowness issue by using ioremap_cache().
On ARM64, ioremap_cache() is also required as the host also maps the VRAM
cacheable, otherwise VM Connect can't display properly with ioremap() or
ioremap_wc().
With this change, the VRAM on new Hyper-V is as fast as regular RAM, so
it's no longer necessary to use the hacks we added to mitigate the
slowness, i.e. we no longer need to allocate physical memory and use
it to back up the VRAM in Generation-1 VM, and we also no longer need to
allocate physical memory to back up the framebuffer in a Generation-2 VM
and copy the framebuffer to the real VRAM. A further big change will
address these for v5.11.
Fixes: 68a2d20b79b1 ("drivers/video: add Hyper-V Synthetic Video Frame Buffer Driver") Tested-by: Boqun Feng <boqun.feng@gmail.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Link: https://lore.kernel.org/r/20201118000305.24797-1-decui@microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If UFS host device is in runtime-suspended state while UFS shutdown
callback is invoked, UFS device shall be resumed for register
accesses. Currently only UFS local runtime resume function will be invoked
to wake up the host. This is not enough because if someone triggers
runtime resume from block layer, then race may happen between shutdown and
runtime resume flow, and finally lead to unlocked register access.
To fix this, in ufshcd_shutdown(), use pm_runtime_get_sync() instead of
resuming UFS device by ufshcd_runtime_resume() "internally" to let runtime
PM framework manage the whole resume flow.
Link: https://lore.kernel.org/r/20201119062916.12931-1-stanley.chu@mediatek.com Fixes: 57d104c153d3 ("ufs: add UFS power management support") Reviewed-by: Can Guo <cang@codeaurora.org> Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Stefan Agner reported a bug when using zsram on 32-bit Arm machines
with RAM above the 4GB address boundary:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = a27bd01c
[00000000] *pgd=236a0003, *pmd=1ffa64003
Internal error: Oops: 207 [#1] SMP ARM
Modules linked in: mdio_bcm_unimac(+) brcmfmac cfg80211 brcmutil raspberrypi_hwmon hci_uart crc32_arm_ce bcm2711_thermal phy_generic genet
CPU: 0 PID: 123 Comm: mkfs.ext4 Not tainted 5.9.6 #1
Hardware name: BCM2711
PC is at zs_map_object+0x94/0x338
LR is at zram_bvec_rw.constprop.0+0x330/0xa64
pc : [<c0602b38>] lr : [<c0bda6a0>] psr: 60000013
sp : e376bbe0 ip : 00000000 fp : c1e2921c
r10: 00000002 r9 : c1dda730 r8 : 00000000
r7 : e8ff7a00 r6 : 00000000 r5 : 02f9ffa0 r4 : e3710000
r3 : 000fdffe r2 : c1e0ce80 r1 : ebf979a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 30c5383d Table: 235c2a80 DAC: fffffffd
Process mkfs.ext4 (pid: 123, stack limit = 0x495a22e6)
Stack: (0xe376bbe0 to 0xe376c000)
As it turns out, zsram needs to know the maximum memory size, which
is defined in MAX_PHYSMEM_BITS when CONFIG_SPARSEMEM is set, or in
MAX_POSSIBLE_PHYSMEM_BITS on the x86 architecture.
The same problem will be hit on all 32-bit architectures that have a
physical address space larger than 4GB and happen to not enable sparsemem
and include asm/sparsemem.h from asm/pgtable.h.
After the initial discussion, I suggested just always defining
MAX_POSSIBLE_PHYSMEM_BITS whenever CONFIG_PHYS_ADDR_T_64BIT is
set, or provoking a build error otherwise. This addresses all
configurations that can currently have this runtime bug, but
leaves all other configurations unchanged.
I looked up the possible number of bits in source code and
datasheets, here is what I found:
- on ARC, CONFIG_ARC_HAS_PAE40 controls whether 32 or 40 bits are used
- on ARM, CONFIG_LPAE enables 40 bit addressing, without it we never
support more than 32 bits, even though supersections in theory allow
up to 40 bits as well.
- on MIPS, some MIPS32r1 or later chips support 36 bits, and MIPS32r5
XPA supports up to 60 bits in theory, but 40 bits are more than
anyone will ever ship
- On PowerPC, there are three different implementations of 36 bit
addressing, but 32-bit is used without CONFIG_PTE_64BIT
- On RISC-V, the normal page table format can support 34 bit
addressing. There is no highmem support on RISC-V, so anything
above 2GB is unused, but it might be useful to eventually support
CONFIG_ZRAM for high pages.
Fixes: 61989a80fb3a ("staging: zsmalloc: zsmalloc memory allocation library") Fixes: 02390b87a945 ("mm/zsmalloc: Prepare to variable MAX_PHYSMEM_BITS") Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Acked-by: Mike Rapoport <rppt@linux.ibm.com> Link: https://lore.kernel.org/linux-mm/bdfa44bf1c570b05d6c70898e2bbb0acf234ecdf.1604762181.git.stefan@agner.ch/ Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Based on more testing, commit 8ca5ee624b4c ("ARM: OMAP2+: Restore MPU
power domain if cpu_cluster_pm_enter() fails") is a poor fix for handling
cpu_cluster_pm_enter() returned errors.
We should not override the cpuidle states with a hardcoded PWRDM_POWER_ON
value. Instead, we should use a configured idle state that does not cause
the context to be lost. Otherwise we end up configuring a potentially
improper state for the MPUSS. We also want to update the returned state
index for the selected state.
Let's just select the highest power idle state C1 to ensure no context
loss is allowed on cpu_cluster_pm_enter() errors. With these changes we
can now unconditionally call omap4_enter_lowpower() for WFI like we did
earlier before commit 55be2f50336f ("ARM: OMAP2+: Handle errors for
cpu_pm"). And we can return the selected state index.
Fixes: 8f04aea048d5 ("ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails") Fixes: 55be2f50336f ("ARM: OMAP2+: Handle errors for cpu_pm") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bail out early from sysc_wait_softreset() just like we do in sysc_reset()
if there's no sysstatus srst_shift to fix a bogus resetdone warning on
enable as suggested by Grygorii Strashko <grygorii.strashko@ti.com>.
We do not currently handle resets for modules that need writing to the
sysstatus register. If we at some point add that, we also need to add
SYSS_QUIRK_RESETDONE_INVERTED flag for cpsw as the sysstatus bit is low
when reset is done as described in the am335x TRM "Table 14-202
SOFT_RESET Register Field Descriptions"
Fixes: d46f9fbec719 ("bus: ti-sysc: Use optional clocks on for enable and wait for softreset bit") Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
When adding __user annotations in commit 2adf5352a34a, the
strncpy_from_user() function declaration for the
CONFIG_GENERIC_STRNCPY_FROM_USER case was missed. Fix it.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Message-Id: <20200831210937.17938-1-laurent.pinchart@ideasonboard.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This change switches rapl to use PMU_FORMAT_ATTR, and fixes two other
macros to use device_attribute instead of kobj_attribute to avoid
callback type mismatches that trip indirect call checking with Clang's
Control-Flow Integrity (CFI).
Maurizio found a race where the abort and cmd stop paths can race as
follows:
1. thread1 runs iscsit_release_commands_from_conn and sets
CMD_T_FABRIC_STOP.
2. thread2 runs iscsit_aborted_task and then does __iscsit_free_cmd. It
then returns from the aborted_task callout and we finish
target_handle_abort and do:
3. thread1 now finishes iscsit_release_commands_from_conn and runs
iscsit_free_cmd while accessing a command we just released.
In __target_check_io_state we check for CMD_T_FABRIC_STOP and set the
CMD_T_ABORTED if the driver is not cleaning up the cmd because of a session
shutdown. However, iscsit_release_commands_from_conn only sets the
CMD_T_FABRIC_STOP and does not check to see if the abort path has claimed
completion ownership of the command.
This adds a check in iscsit_release_commands_from_conn so only the abort or
fabric stop path cleanup the command.
Link: https://lore.kernel.org/r/1605318378-9269-1-git-send-email-michael.christie@oracle.com Reported-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
iSCSI NOPs are sometimes "lost", mistakenly sent to the user-land iscsid
daemon instead of handled in the kernel, as they should be, resulting in a
message from the daemon like:
iscsid: Got nop in, but kernel supports nop handling.
This can occur because of the new forward- and back-locks, and the fact
that an iSCSI NOP response can occur before processing of the NOP send is
complete. This can result in "conn->ping_task" being NULL in
iscsi_nop_out_rsp(), when the pointer is actually in the process of being
set.
To work around this, we add a new state to the "ping_task" pointer. In
addition to NULL (not assigned) and a pointer (assigned), we add the state
"being set", which is signaled with an INVALID pointer (using "-1").
Link: https://lore.kernel.org/r/20201106193317.16993-1-leeman.duncan@gmail.com Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
dmatest: dma0chan0-copy0: result #1: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #2: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #3: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #4: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #5: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #6: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #7: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
dmatest: dma0chan0-copy0: result #8: 'test passed' with src_off=0x0 dst_off=0x0 len=0x400000
We might not do the final se_cmd put from vhost_scsi_complete_cmd_work.
When the last put happens a little later then we could race where
vhost_scsi_complete_cmd_work does vhost_signal, the guest runs and sends
more IO, and vhost_scsi_handle_vq runs but does not find any free cmds.
This patch has us delay completing the cmd until the last lio core ref
is dropped. We then know that once we signal to the guest that the cmd
is completed that if it queues a new command it will find a free cmd.
Signed-off-by: Mike Christie <michael.christie@oracle.com> Reviewed-by: Maurizio Lombardi <mlombard@redhat.com> Link: https://lore.kernel.org/r/1604986403-4931-4-git-send-email-michael.christie@oracle.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If Doorbell Buffer Config command fails even 'dev->dbbuf_dbs != NULL'
which means OACS indicates that NVME_CTRL_OACS_DBBUF_SUPP is set,
nvme_dbbuf_update_and_check_event() will check event even it's not been
successfully set.
This patch fixes mismatch among dbbuf for sq/cqs in case that dbbuf
command fails.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If this is attempted by a kthread, then return -EOPNOTSUPP as we don't
currently support that. Once we can get task_pid_ptr() doing the right
thing, then this can go away again.
The battery status is also being reported by the logitech-hidpp driver,
so ignore the standard HID battery status to avoid reporting the same
info twice.
Note the logitech-hidpp battery driver provides more info, such as properly
differentiating between charging and discharging. Also the standard HID
battery info seems to be wrong, reporting a capacity of just 26% after
fully charging the device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Like the MX5000 and MX5500 quad/bluetooth keyboards the Dinovo Edge also
needs the HIDPP_CONSUMER_VENDOR_KEYS quirk for some special keys to work.
Specifically without this the "Phone" and the 'A' - 'D' Smart Keys do not
send any events.
In addition to fixing these keys not sending any events, adding the
Bluetooth match, so that hid-logitech-hidpp is used instead of the
generic HID driver, also adds battery monitoring support when the
keyboard is connected over Bluetooth.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The secondary CPUs are not activated with the nosmt mitigations and only
the primary thread on each CPU core is used. In this situation,
xen_hvm_smp_prepare_cpus(), and more importantly xen_init_lock_cpu(), is
not called, so the lock_kicker_irq is not initialized for the secondary
CPUs. Let's fix this by exiting early in xen_uninit_lock_cpu() if the
irq is not set to avoid the warning from above for each secondary CPU.
Signed-off-by: Brian Masney <bmasney@redhat.com> Link: https://lore.kernel.org/r/20201107011119.631442-1-bmasney@redhat.com Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The xilinx_dma_poll_timeout macro is sometimes called while holding a
spinlock (see xilinx_dma_issue_pending() for an example) this means we
shouldn't sleep when polling the dma channel registers. To address it
in xilinx poll timeout macro use readl_poll_timeout_atomic instead of
readl_poll_timeout variant.
When DMA_RALINK is enabled and DMADEVICES is disabled, it results in the
following Kbuild warnings:
WARNING: unmet direct dependencies detected for DMA_ENGINE
Depends on [n]: DMADEVICES [=n]
Selected by [y]:
- DMA_RALINK [=y] && STAGING [=y] && RALINK [=y] && !SOC_RT288X [=n]
WARNING: unmet direct dependencies detected for DMA_VIRTUAL_CHANNELS
Depends on [n]: DMADEVICES [=n]
Selected by [y]:
- DMA_RALINK [=y] && STAGING [=y] && RALINK [=y] && !SOC_RT288X [=n]
The reason is that DMA_RALINK selects DMA_ENGINE and DMA_VIRTUAL_CHANNELS
without depending on or selecting DMADEVICES while DMA_ENGINE and
DMA_VIRTUAL_CHANNELS are subordinate to DMADEVICES. This can also fail
building the kernel as demonstrated in a bug report.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Some HID devices don't use a report ID because they only have a single
report. In those cases, the report ID in struct hid_report will be zero
and the data for the report will start at the first byte, so don't skip
over the first byte.
The i8042 module exports several symbols which may be used by other
modules.
Before this commit it would refuse to load (when built as a module itself)
on systems without an i8042 controller.
This is a problem specifically for the asus-nb-wmi module. Many Asus
laptops support the Asus WMI interface. Some of them have an i8042
controller and need to use i8042_install_filter() to filter some kbd
events. Other models do not have an i8042 controller (e.g. they use an
USB attached kbd).
Before this commit the asus-nb-wmi driver could not be loaded on Asus
models without an i8042 controller, when the i8042 code was built as
a module (as Arch Linux does) because the module_init function of the
i8042 module would fail with -ENODEV and thus the i8042_install_filter
symbol could not be loaded.
This commit fixes this by exiting from module_init with a return code
of 0 if no controller is found. It also adds a i8042_present bool to
make the module_exit function a no-op in this case and also adds a
check for i8042_present to the exported i8042_command function.
The latter i8042_present check should not really be necessary because
when builtin that function can already be used on systems without
an i8042 controller, but better safe then sorry.
Reported-and-tested-by: Marius Iacob <themariusus@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20201008112628.3979-2-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Varmilo VA104M Keyboard (04b4:07b1, reported as Varmilo Z104M)
exposes media control hotkeys as a USB HID consumer control device, but
these keys do not work in the current (5.8-rc1) kernel due to the
incorrect HID report descriptor. Fix the problem by modifying the
internal HID report descriptor.
More specifically, the keyboard report descriptor specifies the
logical boundary as 572~10754 (0x023c ~ 0x2a02) while the usage
boundary is specified as 0~10754 (0x00 ~ 0x2a02). This results in an
incorrect interpretation of input reports, causing inputs to be ignored.
By setting the Logical Minimum to zero, we align the logical boundary
with the Usage ID boundary.
Some notes:
* There seem to be multiple variants of the VA104M keyboard. This
patch specifically targets 04b4:07b1 variant.
* The device works out-of-the-box on Windows platform with the generic
consumer control device driver (hidserv.inf). This suggests that
Windows either ignores the Logical Minimum/Logical Maximum or
interprets the Usage ID assignment differently from the linux
implementation; Maybe there are other devices out there that only
works on Windows due to this problem?
Signed-off-by: Frank Yang <puilp0502@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
The usb-hid keyboard-dock for the Acer Switch 10 SW5-012 model declares
an application and hid-usage page of 0x0088 for the INPUT(4) report which
it sends. This reports contains 2 8-bit fields which are declared as
HID_MAIN_ITEM_VARIABLE.
The keyboard-touchpad combo never actually generates this report, except
when the touchpad is toggled on/off with the Fn + F7 hotkey combo. The
toggle on/off is handled inside the keyboard-dock, when the touchpad is
toggled off it simply stops sending events.
When the touchpad is toggled on/off an INPUT(4) report is generated with
the first content byte set to 120/121, before this commit the kernel
would report this as ABS_MISC 120/121 events.
Patch the descriptor to replace the HID_MAIN_ITEM_VARIABLE with
HID_MAIN_ITEM_RELATIVE (because no key-presss release events are send)
and add mappings for the 0x00880078 and 0x00880079 usages to generate
touchpad on/off key events when the touchpad is toggled on/off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Trust Flex Design Tablet has an UGTizer USB ID and requires the same
initialization as the UGTizer GP0610 to be detected as a graphics tablet
instead of a mouse.
Signed-off-by: Martijn van de Streek <martijn@zeewinde.xyz> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
With hardware dirty bit management, calling pte_wrprotect() on a writable,
dirty PTE will lose the dirty state and return a read-only, clean entry.
Move the logic from ptep_set_wrprotect() into pte_wrprotect() to ensure that
the dirty bit is preserved for writable entries, as this is required for
soft-dirty bit management if we enable it in the future.
Cc: <stable@vger.kernel.org> Fixes: 2f4b829c625e ("arm64: Add support for hardware updates of the access and dirty pte bits") Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/20201120143557.6715-3-will@kernel.org Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pte_accessible() is used by ptep_clear_flush() to figure out whether TLB
invalidation is necessary when unmapping pages for reclaim. Although our
implementation is correct according to the architecture, returning true
only for valid, young ptes in the absence of racing page-table
modifications, this is in fact flawed due to lazy invalidation of old
ptes in ptep_clear_flush_young() where we elide the expensive DSB
instruction for completing the TLB invalidation.
Rather than penalise the aging path, adjust pte_accessible() to return
true for any valid pte, even if the access flag is cleared.
kvm_cpu_accept_dm_intr and kvm_vcpu_ready_for_interrupt_injection are
a hodge-podge of conditions, hacked together to get something that
more or less works. But what is actually needed is much simpler;
in both cases the fundamental question is, do we have a place to stash
an interrupt if userspace does KVM_INTERRUPT?
In userspace irqchip mode, that is !vcpu->arch.interrupt.injected.
Currently kvm_event_needs_reinjection(vcpu) covers it, but it is
unnecessarily restrictive.
In split irqchip mode it's a bit more complicated, we need to check
kvm_apic_accept_pic_intr(vcpu) (the IRQ window exit is basically an INTACK
cycle and thus requires ExtINTs not to be masked) as well as
!pending_userspace_extint(vcpu). However, there is no need to
check kvm_event_needs_reinjection(vcpu), since split irqchip keeps
pending ExtINT state separate from event injection state, and checking
kvm_cpu_has_interrupt(vcpu) is wrong too since ExtINT has higher
priority than APIC interrupts. In fact the latter fixes a bug:
when userspace requests an IRQ window vmexit, an interrupt in the
local APIC can cause kvm_cpu_has_interrupt() to be true and thus
kvm_vcpu_ready_for_interrupt_injection() to return false. When this
happens, vcpu_run does not exit to userspace but the interrupt window
vmexits keep occurring. The VM loops without any hope of making progress.
we realize two things. First, thanks to the previous patch the complex
conditional can reuse !kvm_cpu_has_extint(vcpu). Second, the interrupt
window request in vcpu_enter_guest()
should be kept in sync with kvm_vcpu_ready_for_interrupt_injection():
it is unnecessary to ask the processor for an interrupt window
if we would not be able to return to userspace. Therefore,
kvm_cpu_accept_dm_intr(vcpu) is basically !kvm_cpu_has_extint(vcpu)
ANDed with the existing check for masked ExtINT. It all makes sense:
- we can accept an interrupt from userspace if there is a place
to stash it (and, for irqchip split, ExtINTs are not masked).
Interrupts from userspace _can_ be accepted even if right now
EFLAGS.IF=0.
- in order to tell userspace we will inject its interrupt ("IRQ
window open" i.e. kvm_vcpu_ready_for_interrupt_injection), both
KVM and the vCPU need to be ready to accept the interrupt.
... and this is what the patch implements.
Reported-by: David Woodhouse <dwmw@amazon.co.uk> Analyzed-by: David Woodhouse <dwmw@amazon.co.uk> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Nikos Tsironis <ntsironis@arrikto.com> Reviewed-by: David Woodhouse <dwmw@amazon.co.uk> Tested-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Centralize handling of interrupts from the userspace APIC
in kvm_cpu_has_extint and kvm_cpu_get_extint, since
userspace APIC interrupts are handled more or less the
same as ExtINTs are with split irqchip. This removes
duplicated code from kvm_cpu_has_injectable_intr and
kvm_cpu_has_interrupt, and makes the code more similar
between kvm_cpu_has_{extint,interrupt} on one side
and kvm_cpu_get_{extint,interrupt} on the other.
Cc: stable@vger.kernel.org Reviewed-by: Filippo Sironi <sironi@amazon.de> Reviewed-by: David Woodhouse <dwmw@amazon.co.uk> Tested-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's "expected" that users will access registers in the redistributor if
the RD has been properly configured (e.g., the RD base address is set). But
it hasn't yet been covered by the existing documentation.
Per discussion on the list [1], the reporting of the GICR_TYPER.Last bit
for userspace never actually worked. And it's difficult for us to emulate
it correctly given that userspace has the flexibility to access it any
time. Let's just drop the reporting of the Last bit for userspace for now
(userspace should have full knowledge about it anyway) and it at least
prevents kernel from panic ;-)
When accessing the ESB page of a source interrupt, the fault handler
will retrieve the page address from the XIVE interrupt 'xive_irq_data'
structure. If the associated KVM XIVE interrupt is not valid, that is
not allocated at the HW level for some reason, the fault handler will
dereference a NULL pointer leading to the oops below :
Mid callback needs to be called only when valid data is
read into pages.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that could cause a refcount use after free:
Workqueue: smb3decryptd smb2_decrypt_offload [cifs]
Signed-off-by: Rohith Surabattula <rohiths@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> #5.4+ Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reconnect happens Mid queue can be corrupted when both
demultiplex and offload thread try to dequeue the MID from the
pending list.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that could cause a refcount use after free:
Workqueue: smb3decryptd smb2_decrypt_offload [cifs]
Signed-off-by: Rohith Surabattula <rohiths@microsoft.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> #5.4+ Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cifs_reconnect needs to be called only from demultiplex thread.
skip cifs_reconnect in offload thread. So, cifs_reconnect will be
called by demultiplex thread in subsequent request.
These patches address a problem found during decryption offload:
CIFS: VFS: trying to dequeue a deleted mid
that can cause a refcount use after free:
When compiling inside the kernel include linux/stddef.h instead of
stddef.h. When I compile this header file in backports for power PC I
run into a conflict with ptrdiff_t. I was unable to reproduce this in
mainline kernel. I still would like to fix this problem in the kernel.
Fixes: 6989310f5d43 ("wireless: Use offsetof instead of custom macro.") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Link: https://lore.kernel.org/r/20200521201422.16493-1-hauke@hauke-m.de Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This happens because at btrfs_read_qgroup_config() we can call
qgroup_rescan_init() while holding a read lock on a quota btree leaf,
acquired by the previous call to btrfs_search_slot_for_read(), and
qgroup_rescan_init() acquires the mutex qgroup_rescan_lock.
A qgroup rescan worker does the opposite: it acquires the mutex
qgroup_rescan_lock, at btrfs_qgroup_rescan_worker(), and then tries to
update the qgroup status item in the quota btree through the call to
update_qgroup_status_item(). This inversion of locking order
between the qgroup_rescan_lock mutex and quota btree locks causes the
splat.
Fix this simply by releasing and freeing the path before calling
qgroup_rescan_init() at btrfs_read_qgroup_config().
CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported a possible use-after-free when printing a duplicate device
warning device_list_add().
At this point it can happen that a btrfs_device::fs_info is not correctly
setup yet, so we're accessing stale data, when printing the warning
message using the btrfs_printk() wrappers.
==================================================================
BUG: KASAN: use-after-free in btrfs_printk+0x3eb/0x435 fs/btrfs/super.c:245
Read of size 8 at addr ffff8880878e06a8 by task syz-executor225/7068
The syzkaller reproducer for this use-after-free crafts a filesystem image
and loop mounts it twice in a loop. The mount will fail as the crafted
image has an invalid chunk tree. When this happens btrfs_mount_root() will
call deactivate_locked_super(), which then cleans up fs_info and
fs_info::sb. If a second thread now adds the same block-device to the
filesystem, it will get detected as a duplicate device and
device_list_add() will reject the duplicate and print a warning. But as
the fs_info pointer passed in is non-NULL this will result in a
use-after-free.
Instead of printing possibly uninitialized or already freed memory in
btrfs_printk(), explicitly pass in a NULL fs_info so the printing of the
device name will be skipped altogether.
There was a slightly different approach discussed in
https://lore.kernel.org/linux-btrfs/20200114060920.4527-1-anand.jain@oracle.com/t/#u
Link: https://lore.kernel.org/linux-btrfs/000000000000c9e14b05afcc41ba@google.com Reported-by: syzbot+582e66e5edf36a22c7b0@syzkaller.appspotmail.com CC: stable@vger.kernel.org # 4.19+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: Anand Jain <anand.jain@oracle.com> Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are sectorsize alignment checks that are reported but then
check_extent_data_ref continues. This was not intended, wrong alignment
is not a minor problem and we should return with error.
Cong Wang [Sat, 21 Nov 2020 03:43:17 +0000 (19:43 -0800)]
netfilter: clear skb->next in NF_HOOK_LIST()
NF_HOOK_LIST() uses list_del() to remove skb from the linked list,
however, it is not sufficient as skb->next still points to other
skb. We should just call skb_list_del_init() to clear skb->next,
like the rest places which using skb list.
This has been fixed in upstream by commit ca58fbe06c54
("netfilter: add and use nf_hook_slow_list()").
Fixes: 9f17dbf04ddf ("netfilter: fix use-after-free in NF_HOOK_LIST") Reported-by: liuzx@knownsec.com Tested-by: liuzx@knownsec.com Cc: Florian Westphal <fw@strlen.de> Cc: Edward Cree <ecree@solarflare.com> Cc: stable@vger.kernel.org # between 4.19 and 5.4 Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use IS_ENABLED instead, which is true for both built-ins and modules.
Otherwise, a
> ip -4 route add 1.2.3.4/32 via inet6 fe80::2 dev eth1
fails with the message "Error: IPv6 support not enabled in kernel." if
CONFIG_IPV6 is `m`.
bcm2835_spi_remove() accesses the driver's private data after calling
spi_unregister_controller() even though that function releases the last
reference on the spi_controller and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
bcm_qspi_remove() calls spi_unregister_master() even though
bcm_qspi_probe() calls devm_spi_register_master(). The spi_master is
therefore unregistered and freed twice on unbind.
Moreover, since commit 0392727c261b ("spi: bcm-qspi: Handle clock probe
deferral"), bcm_qspi_probe() leaks the spi_master allocation if the call
to devm_clk_get_optional() fails.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound and also
avoids the spi_master leak on probe.
While at it, fix an ordering issue in bcm_qspi_remove() wherein
spi_unregister_master() is called after uninitializing the hardware,
disabling the clock and freeing an IRQ data structure. The correct
order is to call spi_unregister_master() *before* those teardown steps
because bus accesses may still be ongoing until that function returns.
enqueue_task_fair() attempts to skip the overutilized update for new
tasks as their util_avg is not accurate yet. However, the flag we check
to do so is overwritten earlier on in the function, which makes the
condition pretty much a nop.
Fix this by saving the flag early on.
Fixes: 2802bf3cd936 ("sched/fair: Add over-utilization/tipping point indicator") Reported-by: Rick Yiu <rickyiu@google.com> Signed-off-by: Quentin Perret <qperret@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Link: https://lkml.kernel.org/r/20201112111201.2081902-1-qperret@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When boosting is enabled, it is observed that rate of atomic order-0
allocation failures are high due to the fact that free levels in the
system are checked with ->watermark_boost offset. This is not a problem
for sleepable allocations but for atomic allocations which looks like
regression.
This problem is seen frequently on system setup of Android kernel running
on Snapdragon hardware with 4GB RAM size. When no extfrag event occurred
in the system, ->watermark_boost factor is zero, thus the watermark
configurations in the system are:
After launching some memory hungry applications in Android which can cause
extfrag events in the system to an extent that ->watermark_boost can be
set to max i.e. default boost factor makes it to 150% of high watermark.
With default system configuration, for an atomic order-0 allocation to
succeed, having free memory of ~2MB will suffice. But boosting makes the
min_wmark to ~61MB thus for an atomic order-0 allocation to be successful
system should have minimum of ~23MB of free memory(from calculations of
zone_watermark_ok(), min = 3/4(min/2)). But failures are observed despite
system is having ~20MB of free memory. In the testing, this is
reproducible as early as first 300secs since boot and with furtherlowram
configurations(<2GB) it is observed as early as first 150secs since boot.
These failures can be avoided by excluding the ->watermark_boost in
watermark caluculations for atomic order-0 allocations.
Alexander reported a syzkaller / KASAN finding on s390, see below for
complete output.
In do_huge_pmd_anonymous_page(), the pre-allocated pagetable will be
freed in some cases. In the case of userfaultfd_missing(), this will
happen after calling handle_userfault(), which might have released the
mmap_lock. Therefore, the following pte_free(vma->vm_mm, pgtable) will
access an unstable vma->vm_mm, which could have been freed or re-used
already.
For all architectures other than s390 this will go w/o any negative
impact, because pte_free() simply frees the page and ignores the
passed-in mm. The implementation for SPARC32 would also access
mm->page_table_lock for pte_free(), but there is no THP support in
SPARC32, so the buggy code path will not be used there.
For s390, the mm->context.pgtable_list is being used to maintain the 2K
pagetable fragments, and operating on an already freed or even re-used
mm could result in various more or less subtle bugs due to list /
pagetable corruption.
Fix this by calling pte_free() before handle_userfault(), similar to how
it is already done in __do_huge_pmd_anonymous_page() for the WRITE /
non-huge_zero_page case.
Commit 6b251fc96cf2c ("userfaultfd: call handle_userfault() for
userfaultfd_missing() faults") actually introduced both, the
do_huge_pmd_anonymous_page() and also __do_huge_pmd_anonymous_page()
changes wrt to calling handle_userfault(), but only in the latter case
it put the pte_free() before calling handle_userfault().
BUG: KASAN: use-after-free in do_huge_pmd_anonymous_page+0xcda/0xd90 mm/huge_memory.c:744
Read of size 8 at addr 00000000962d6988 by task syz-executor.0/9334
Memory state around the buggy address: 00000000962d6880: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00000000962d6900: 00 fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb
>00000000962d6980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ 00000000962d6a00: fb fb fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00000000962d6a80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
==================================================================
If we reparent the slab objects to the root memcg, when we free the slab
object, we need to update the per-memcg vmstats to keep it correct for
the root memcg. Now this at least affects the vmstat of
NR_KERNEL_STACK_KB for !CONFIG_VMAP_STACK when the thread stack size is
smaller than the PAGE_SIZE.
David said:
"I assume that without this fix that the root memcg's vmstat would
always be inflated if we reparented"
Fixes: ec9f02384f60 ("mm: workingset: fix vmstat counters for shadow nodes") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Roman Gushchin <guro@fb.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: David Rientjes <rientjes@google.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: Christopher Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Roman Gushchin <guro@fb.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Yafang Shao <laoar.shao@gmail.com> Cc: Chris Down <chris@chrisdown.name> Cc: <stable@vger.kernel.org> [5.3+] Link: https://lkml.kernel.org/r/20201110031015.15715-1-songmuchun@bytedance.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, scan_microcode() leverages microcode_matches() to check
if the microcode matches the CPU by comparing the family and model.
However, the processor stepping and flags of the microcode signature
should also be considered when saving a microcode patch for early
update.
Use find_matching_signature() in scan_microcode() and get rid of the
now-unused microcode_matches() which is a good cleanup in itself.
Complete the verification of the patch being saved for early loading in
save_microcode_patch() directly. This needs to be done there too because
save_mc_for_early() will call save_microcode_patch() too.
The second reason why this needs to be done is because the loader still
tries to support, at least hypothetically, mixed-steppings systems and
thus adds all patches to the cache that belong to the same CPU model
albeit with different steppings.
For example:
microcode: CPU: sig=0x906ec, pf=0x2, rev=0xd6
microcode: mc_saved[0]: sig=0x906e9, pf=0x2a, rev=0xd6, total size=0x19400, date = 2020-04-23
microcode: mc_saved[1]: sig=0x906ea, pf=0x22, rev=0xd6, total size=0x19000, date = 2020-04-27
microcode: mc_saved[2]: sig=0x906eb, pf=0x2, rev=0xd6, total size=0x19400, date = 2020-04-23
microcode: mc_saved[3]: sig=0x906ec, pf=0x22, rev=0xd6, total size=0x19000, date = 2020-04-27
microcode: mc_saved[4]: sig=0x906ed, pf=0x22, rev=0xd6, total size=0x19400, date = 2020-04-23
The patch which is being saved for early loading, however, can only be
the one which fits the CPU this runs on so do the signature verification
before saving.
[ bp: Do signature verification in save_microcode_patch()
and rewrite commit message. ]
Commit 69f594a38967 ("ptrace: do not audit capability check when outputing
/proc/pid/stat") replaced the use of ns_capable() with
has_ns_capability{,_noaudit}() which doesn't set PF_SUPERPRIV.
Commit 6b3ad6649a4c ("ptrace: reintroduce usage of subjective credentials in
ptrace_has_cap()") replaced has_ns_capability{,_noaudit}() with
security_capable(), which doesn't set PF_SUPERPRIV neither.
Since commit 98f368e9e263 ("kernel: Add noaudit variant of ns_capable()"), a
new ns_capable_noaudit() helper is available. Let's use it!
As a result, the signature of ptrace_has_cap() is restored to its original one.
Cc: Christian Brauner <christian.brauner@ubuntu.com> Cc: Eric Paris <eparis@redhat.com> Cc: Jann Horn <jannh@google.com> Cc: Kees Cook <keescook@chromium.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Serge E. Hallyn <serge@hallyn.com> Cc: Tyler Hicks <tyhicks@linux.microsoft.com> Cc: stable@vger.kernel.org Fixes: 6b3ad6649a4c ("ptrace: reintroduce usage of subjective credentials in ptrace_has_cap()") Fixes: 69f594a38967 ("ptrace: do not audit capability check when outputing /proc/pid/stat") Signed-off-by: Mickaël Salaün <mic@linux.microsoft.com> Reviewed-by: Jann Horn <jannh@google.com> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20201030123849.770769-2-mic@digikod.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A UHS setting of SDR25 can give better results for High Speed mode.
This is because there is no setting corresponding to high speed. Currently
SDHCI sets no value, which means zero which is also the setting for SDR12.
There was an attempt to change this in sdhci.c but it caused problems for
some drivers, so it was reverted and the change was made to sdhci-brcmstb
in commit 2fefc7c5f7d16e ("mmc: sdhci-brcmstb: Fix incorrect switch to HS
mode"). Several other drivers also do this.
EDID can declare the maximum supported bpc up to 16,
and apparently there are displays that do so. Currently
we assume 12 bpc is tha max. Fix the assumption and
toss in a MISSING_CASE() for any other value we don't
expect to see.
This fixes modesets with a display with EDID max bpc > 12.
Previously any modeset would just silently fail on platforms
that didn't otherwise limit this via the max_bpc property.
In particular we don't add the max_bpc property to HDMI
ports on gmch platforms, and thus we would see the raw
max_bpc coming from the EDID.
I suppose we could already adjust this to also allow 16bpc,
but seeing as no current platform supports that there is
little point.
This was due to hv_synic_cleanup() callback returning -EBUSY to
cpuhp_issue_call() when tearing down the VMBUS_CONNECT_CPU, even
if the vmbus_connection.conn_state = DISCONNECTED. hv_synic_cleanup()
should succeed in the case where vmbus_connection.conn_state
is DISCONNECTED.
Fix is to add an extra condition to test for
vmbus_connection.conn_state == CONNECTED on the VMBUS_CONNECT_CPU and
only return early if true. This way the kexec() path can still shut
everything down while preserving the initial behavior of preventing
CPU offlining on the VMBUS_CONNECT_CPU while the VM is running.
Fixes: 8a857c55420f29 ("Drivers: hv: vmbus: Always handle the VMBus messages on CPU0") Signed-off-by: Chris Co <chrco@microsoft.com> Reviewed-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201110190118.15596-1-chrco@linux.microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd3430d ("s390/dasd: fix handling of internal requests") Cc: <stable@vger.kernel.org> #4.16 Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This file is installed by the s390 CPU Measurement sampling
facility device driver to export supported minimum and
maximum sample buffer sizes.
This file is read by lscpumf tool to display the details
of the device driver capabilities. The lscpumf tool might
be invoked by a non-root user. In this case it does not
print anything because the file contents can not be read.
Fix this by allowing read access for all users. Reading
the file contents is ok, changing the file contents is
left to the root user only.
For further reference and details see:
[1] https://github.com/ibm-s390-tools/s390-tools/issues/97
If sta_info_insert_finish() fails, we currently keep the station
around and free it only in the caller, but there's only one such
caller and it always frees it immediately.
As syzbot found, another consequence of this split is that we can
put things that sleep only into __cleanup_single_sta() and not in
sta_info_free(), but this is the only place that requires such of
sta_info_free() now.
Change this to free the station in sta_info_insert_finish(), in
which case we can still sleep. This will also let us unify the
cleanup code later.
Some drivers fill the status rate list without setting the rate index after
the final rate to -1. minstrel_ht already deals with this, but minstrel
doesn't, which causes it to get stuck at the lowest rate on these drivers.
Fix this by checking the count as well.
Cc: stable@vger.kernel.org Fixes: cccf129f820e ("mac80211: add the 'minstrel' rate control algorithm") Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20201111183359.43528-3-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Deferring sampling attempts to the second stage has some bad interactions
with drivers that process the rate table in hardware and use the probe flag
to indicate probing packets (e.g. most mt76 drivers). On affected drivers
it can lead to probing not working at all.
If the link conditions turn worse, it might not be such a good idea to
do a lot of sampling for lower rates in this case.
Fix this by simply skipping the sample attempt instead of deferring it,
but keep the checks that would allow it to be sampled if it was skipped
too often, but only if it has less than 95% success probability.
Also ensure that IEEE80211_TX_CTL_RATE_CTRL_PROBE is set for all probing
packets.
Cc: stable@vger.kernel.org Fixes: cccf129f820e ("mac80211: add the 'minstrel' rate control algorithm") Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20201111183359.43528-2-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although cache alias management calls set up and tear down TLB entries
and fast_second_level_miss is able to restore TLB entry should it be
evicted they absolutely cannot preempt each other because they use the
same TLBTEMP area for different purposes.
Disable preemption around all cache alias management calls to enforce
that.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fast_second_level_miss handler for the TLBTEMP area has an assumption
that page table directory entry for the TLBTEMP address range is 0. For
it to be true the TLBTEMP area must be aligned to 4MB boundary and not
share its 4MB region with anything that may use a page table. This is
not true currently: TLBTEMP shares space with vmalloc space which
results in the following kinds of runtime errors when
fast_second_level_miss loads page table directory entry for the vmalloc
space instead of fixing up the TLBTEMP area:
Workaround regulators whose supply name happens to be the same as its
own name. This fixes boards that used to work before the early supply
resolving was removed. The error message is left in place so that
offending drivers can be detected.
Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator") Cc: stable@vger.kernel.org Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1 Link: https://lore.kernel.org/r/d703acde2a93100c3c7a81059d716c50ad1b1f52.1605226675.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a regulator's name equals its supply's name the
regulator_resolve_supply() recurses indefinitely. Add a check
so that debugging the problem is easier. The "fixed" commit
just exposed the problem.
Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator") Cc: stable@vger.kernel.org Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1 Link: https://lore.kernel.org/r/c6171057cfc0896f950c4d8cb82df0f9f1b89ad9.1605226675.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed commit introduced a possible second call to
set_machine_constraints() and that allocates memory for
rdev->constraints. Move the allocation to the caller so
it's easier to manage and done once.
Fixes: aea6cb99703e ("regulator: resolve supply after creating regulator") Cc: stable@vger.kernel.org Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de> # stpmic1 Link: https://lore.kernel.org/r/78c3d4016cebc08d441aad18cb924b4e4d9cf9df.1605226675.git.mirq-linux@rere.qmqm.pl Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Limit the fsl,pfuze-support-disable-sw to the pfuze100 and pfuze200
variants.
When enabling fsl,pfuze-support-disable-sw and using a pfuze3000 or
pfuze3001, the driver would choose pfuze100_sw_disable_regulator_ops
instead of the newly introduced and correct pfuze3000_sw_regulator_ops.
Signed-off-by: Sean Nyekjaer <sean@geanix.com> Fixes: 6f1cf5257acc ("regualtor: pfuze100: correct sw1a/sw2 on pfuze3000") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201110174113.2066534-1-sean@geanix.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bcm2835aux_spi_remove() accesses the driver's private data after calling
spi_unregister_master() even though that function releases the last
reference on the spi_master and thereby frees the private data.
Fix by switching over to the new devm_spi_alloc_master() helper which
keeps the private data accessible until the driver has unbound.
If the calls to of_match_device(), of_alias_get_id(),
devm_ioremap_resource(), devm_regmap_init_mmio() or devm_clk_get()
fail on probe of the NPCM FIU SPI driver, the spi_controller struct is
erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
SPI driver probing currently comprises two steps, whereas removal
comprises only one step:
spi_alloc_master()
spi_register_controller()
spi_unregister_controller()
That's because spi_unregister_controller() calls device_unregister()
instead of device_del(), thereby releasing the reference on the
spi_controller which was obtained by spi_alloc_master().
An SPI driver's private data is contained in the same memory allocation
as the spi_controller struct. Thus, once spi_unregister_controller()
has been called, the private data is inaccessible. But some drivers
need to access it after spi_unregister_controller() to perform further
teardown steps.
Introduce devm_spi_alloc_master() and devm_spi_alloc_slave(), which
release a reference on the spi_controller struct only after the driver
has unbound, thereby keeping the memory allocation accessible. Change
spi_unregister_controller() to not release a reference if the
spi_controller was allocated by one of these new devm functions.
The present commit is small enough to be backportable to stable.
It allows fixing drivers which use the private data in their ->remove()
hook after it's been freed. It also allows fixing drivers which neglect
to release a reference on the spi_controller in the probe error path.
Long-term, most SPI drivers shall be moved over to the devm functions
introduced herein. The few that can't shall be changed in a treewide
commit to explicitly release the last reference on the controller.
That commit shall amend spi_unregister_controller() to no longer release
a reference, thereby completing the migration.
As a result, the behaviour will be less surprising and more consistent
with subsystems such as IIO, which also includes the private data in the
allocation of the generic iio_dev struct, but calls device_del() in
iio_device_unregister().
Normally the last reference on an spi_controller is released by
spi_unregister_controller(). In the case of the i.MX lpspi driver,
the spi_controller is registered with devm_spi_register_controller(),
so spi_unregister_controller() is invoked automatically after the driver
has unbound.
However the driver already releases the last reference in
fsl_lpspi_remove() through a gratuitous call to spi_master_put(),
causing a use-after-free when spi_unregister_controller() is
subsequently invoked by the devres framework.
Fix by dropping the superfluous spi_master_put().
Fixes: 944c01a889d9 ("spi: lpspi: enable runtime pm for lpspi") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: <stable@vger.kernel.org> # v5.2+ Cc: Han Xu <han.xu@nxp.com> Link: https://lore.kernel.org/r/ab3c0b18bd820501a12c85e440006e09ec0e275f.1604874488.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_comp field is used in a couple of places but it is never set. This
results in kernel oops when dereferencing a NULL pointer. Set the
`dev_comp` field correctly in the probe function.
Some 360 degree hinges (yoga) style 2-in-1 devices use 2 KXCJ91008-s
to allow the OS to determine the angle between the display and the base
of the device, so that the OS can determine if the 2-in-1 is in laptop
or in tablet-mode.
On Windows both accelerometers are read by a special HingeAngleService
process; and this process calls a DSM (Device Specific Method) on the
ACPI KIOX010A device node for the sensor in the display, to let the
embedded-controller (EC) know about the mode so that it can disable the
kbd and touchpad to avoid spurious input while folded into tablet-mode.
This notifying of the EC is problematic because sometimes the EC comes up
thinking that device is in tablet-mode and the kbd and touchpad do not
work. This happens for example on Irbis NB111 devices after a suspend /
resume cycle (after a complete battery drain / hard reset without having
booted Windows at least once). Other 2-in-1s which are likely affected
too are e.g. the Teclast F5 and F6 series.
The kxcjk-1013 driver may seem like a strange place to deal with this,
but since it is *the* driver for the ACPI KIOX010A device, it is also
the driver which has access to the ACPI handle needed by the DSM.
Add support for calling the DSM and on probe unconditionally tell the
EC that the device is laptop mode, fixing the kbd and touchpad sometimes
not working.
Fixes: 7f6232e69539 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID") Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201110133835.129080-3-hdegoede@redhat.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the boolean is_smo8500_device variable with an acpi_type enum.
For now this can be either ACPI_GENERIC or ACPI_SMO8500, this is a
preparation patch for adding special handling for the KIOX010A ACPI HID,
which will add a ACPI_KIOX010A acpi_type to the introduced enum.
For stable as needed as precursor for next patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Fixes: 7f6232e69539 ("iio: accel: kxcjk1013: Add KIOX010A ACPI Hardware-ID") Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201110133835.129080-2-hdegoede@redhat.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The idea of the warning in ext4_update_dx_flag() is that we should warn
when we are clearing EXT4_INODE_INDEX on a filesystem with metadata
checksums enabled since after clearing the flag, checksums for internal
htree nodes will become invalid. So there's no need to warn (or actually
do anything) when EXT4_INODE_INDEX is not set.
Link: https://lore.kernel.org/r/20201118153032.17281-1-jack@suse.cz Fixes: 48a34311953d ("ext4: fix checksum errors with indexed dirs") Reported-by: Eric Biggers <ebiggers@kernel.org> Reviewed-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When VCNL4035 is enabled and IIO_BUFFER is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_TRIGGERED_BUFFER
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- VCNL4035 [=y] && IIO [=y] && I2C [=y]
The reason is that VCNL4035 selects IIO_TRIGGERED_BUFFER without depending
on or selecting IIO_BUFFER while IIO_TRIGGERED_BUFFER depends on
IIO_BUFFER. This can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fix an error in the mouse / INPUT(2) descriptor used for quad/bt2.0 combo
receivers. Replace INPUT with INPUT (Data,Var,Abs) for the field for the
4 extra buttons which share their report-byte with the low-res hwheel.
This is likely a copy and paste error. I've verified that the new
0x81, 0x02 value matches both the mouse descriptor for the currently
supported MX5000 / MX5500 receivers, as well as the INPUT(2) mouse
descriptors for the Dinovo receivers for which support is being
worked on.
Cc: stable@vger.kernel.org Fixes: f2113c3020ef ("HID: logitech-dj: add support for Logitech Bluetooth Mini-Receiver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d2620 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com> Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code change for switching to non-atomic mode brought the
unexpected mutex deadlock in get_msg(). It converted the spinlock
with the existing mutex, but there were calls with the already holding
the mutex. Since the only place that needs the extra lock is the code
path from snd_mixart_send_msg(), remove the mutex lock in get_msg()
and apply in the caller side for fixing the mutex deadlock.
When processing request to add/replace user-defined element set, check
of given element identifier and decision of numeric identifier is done
in "__snd_ctl_add_replace()" helper function. When the result of check
is wrong, the helper function returns error code. The error code shall
be returned to userspace application.
Current implementation includes bug to return zero to userspace application
regardless of the result. This commit fixes the bug.
Cc: <stable@vger.kernel.org> Fixes: e1a7bfe38079 ("ALSA: control: Fix race between adding and removing a user element") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Link: https://lore.kernel.org/r/20201113092043.16148-1-o-takashi@sakamocchi.jp Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The spin_lock/unlock_irq() functions cannot be nested. The problem is
that presumably we would want the IRQs to be re-enabled on the second
call the spin_unlock_irq() but instead it will be enabled at the first
call so IRQs will be enabled earlier than expected.
In this situation the copy_resp_to_buf() function is only called from
one function and it is called with IRQs disabled. We can just use
the regular spin_lock/unlock() functions.
Speakup has only one speakup_tty variable to store the tty it is managing. This
makes sense since its codebase currently assumes that there is only one user who
controls the screen reading.
That however means that we have to forbid using the line discipline several
times, otherwise the second closure would try to free a NULL ldisc_data, leading to
Some users are pairing the Dinovo keyboards with the MX5000 or MX5500
receivers, instead of with the Dinovo receivers. The receivers are
mostly the same (and the air protocol obviously is compatible) but
currently the Dinovo receivers are handled by hid-lg.c while the
MX5x00 receivers are handled by logitech-dj.c.
When using a Dinovo keyboard, with its builtin touchpad, through
logitech-dj.c then the touchpad stops working because when asking the
receiver for paired devices, we get only 1 paired device with
a device_type of REPORT_TYPE_KEYBOARD. And since we don't see a paired
mouse, we have nowhere to send mouse-events to, so we drop them.
Extend the existing fix for the Dinovo Edge for this to also cover the
Dinovo Mini keyboard and also add a mapping to logitech-hidpp for the
Media key on the Dinovo Mini, so that that keeps working too.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1811424 Fixes: f2113c3020ef ("HID: logitech-dj: add support for Logitech Bluetooth Mini-Receiver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some quad/bluetooth keyboards, such as the Dinovo Edge (Y-RAY81) have a
builtin touchpad. In this case when asking the receiver for paired devices,
we get only 1 paired device with a device_type of REPORT_TYPE_KEYBOARD.
This means that we do not instantiate a second dj_hiddev for the mouse
(as we normally would) and thus there is no place for us to forward the
mouse input reports to, causing the touchpad part of the keyboard to not
work.
There is no way for us to detect these keyboards, so this commit adds
an array with device-ids for such keyboards and when a keyboard is on
this list it adds STD_MOUSE to the reports_supported bitmap for the
dj_hiddev created for the keyboard fixing the touchpad not working.
Using a list of device-ids for this is not ideal, but there are only
very few such keyboards so this should be fine. Besides the Dinovo Edge,
other known wireless Logitech keyboards with a builtin touchpad are:
* Dinovo Mini (TODO add its device-id to the list)
* K400 (uses a unifying receiver so is not affected)
* K600 (uses a unifying receiver so is not affected)
Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1811424 Fixes: f2113c3020ef ("HID: logitech-dj: add support for Logitech Bluetooth Mini-Receiver") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems that the PID 0x4072 was missing from the list Logitech gave me
for this mouse, as I found one with it in the wild (with which I tested
this patch).
Fixes: 4435ff2f09a2 ("HID: logitech: Enable high-resolution scrolling on Logitech mice") Signed-off-by: Harry Cutts <hcutts@chromium.org> Acked-by: Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
The attr->set() receive a value of u64, but simple_strtoll() is used for
doing the conversion. It will lead to the error cast if user inputs a
negative value.
Use kstrtoull() instead of simple_strtoll() to convert a string got from
the user to an unsigned value. The former will return '-EINVAL' if it
gets a negetive value, but the latter can't handle the situation
correctly. Make 'val' unsigned long long as what kstrtoull() takes,
this will eliminate the compile warning on no 64-bit architectures.
Fixes: f7b88631a897 ("fs/libfs.c: fix simple_attr_write() on 32bit machines") Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Link: https://lkml.kernel.org/r/1605341356-11872-1-git-send-email-yangyicong@hisilicon.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
