The iopf_queue_remove_device() helper removes a device from the per-iommu
iopf queue when PRI is disabled on the device. It responds to all
outstanding iopf's with an IOMMU_PAGE_RESP_INVALID code and detaches the
device from the queue.
However, it fails to release the group structure that represents a group
of iopf's awaiting for a response after responding to the hardware. This
can cause a memory leak if iopf_queue_remove_device() is called with
pending iopf's.
Fix it by calling iopf_free_group() after the iopf group is responded.
Fixes: 199112327135 ("iommu: Track iopf group instead of last fault") Cc: stable@vger.kernel.org Suggested-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Link: https://lore.kernel.org/r/20250117055800.782462-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scx_move_task() is called from sched_move_task() and tells the BPF scheduler
that cgroup migration is being committed. sched_move_task() is used by both
cgroup and autogroup migrations and scx_move_task() tried to filter out
autogroup migrations by testing the destination cgroup and PF_EXITING but
this is not enough. In fact, without explicitly tagging the thread which is
doing the cgroup migration, there is no good way to tell apart
scx_move_task() invocations for racing migration to the root cgroup and an
autogroup migration.
This led to scx_move_task() incorrectly ignoring a migration from non-root
cgroup to an autogroup of the root cgroup triggering the following warning:
Fix it by adding an argument to sched_move_task() that indicates whether the
moving is for a cgroup or autogroup migration. After the change,
scx_move_task() is called only for cgroup migrations and renamed to
scx_cgroup_move_task().
- The bailout for a bad partoffset must use put_dev_sector(), since the
preceding read_part_sector() succeeded.
- If the partition table claims a silly sector size like 0xfff bytes
(which results in partition table entries straddling sector boundaries),
bail out instead of accessing out-of-bounds memory.
- We must not assume that the partition table contains proper NUL
termination - use strnlen() and strncmp() instead of strlen() and
strcmp().
The stmpe_reg_read function can fail, but its return value is not checked
in stmpe_gpio_irq_sync_unlock. This can lead to silent failures and
incorrect behavior if the hardware access fails.
This patch adds checks for the return value of stmpe_reg_read. If the
function fails, an error message is logged and the function returns
early to avoid further issues.
Fixes: b888fb6f2a27 ("gpio: stmpe: i2c transfer are forbiden in atomic context") Cc: stable@vger.kernel.org # 4.16+ Signed-off-by: Wentao Liang <vulab@iscas.ac.cn> Link: https://lore.kernel.org/r/20250212021849.275-1-vulab@iscas.ac.cn Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spurious immediate wake up events are reported on Acer Nitro ANV14. GPIO 11 is
specified as an edge triggered input and also a wake source but this pin is
supposed to be an output pin for an LED, so it's effectively floating.
Block the interrupt from getting set up for this GPIO on this device.
In contrast to the commit message of the fixed commit VFs whose parent
PF is not configured are not always isolated, that is put on their own
PCI domain. This is because for VFs to be added to an existing PCI
domain it is enough for that PCI domain to share the same topology ID or
PCHID. Such a matching PCI domain without a parent PF may exist when
a PF from the same PCI card created the domain with the VF being a child
of a different, non accessible, PF. While not causing technical issues
it makes the rules which VFs are isolated inconsistent.
Fix this by explicitly checking that the parent PF exists on the PCI
domain determined by the topology ID or PCHID before registering the VF.
This works because a parent PF which is under control of this Linux
instance must be enabled and configured at the point where its child VFs
appear because otherwise SR-IOV could not have been enabled on the
parent.
This creates a new zpci_iov_find_parent_pf() function which a future
commit can use to find if a VF has a configured parent PF. Use
zdev->rid instead of zdev->devfn such that the new function can be used
before it has been decided if the RID will be exposed and zdev->devfn is
set. Also handle the hypotheical case that the RID is not available but
there is an otherwise matching zbus.
do_page_fault() and do_entUna() are special because they use
non-standard stack frame layout. Fix them manually.
Cc: stable@vger.kernel.org Tested-by: Maciej W. Rozycki <macro@orcam.me.uk> Tested-by: Magnus Lindholm <linmag7@gmail.com> Tested-by: Matt Turner <mattst88@gmail.com> Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk> Suggested-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Ivan Kokshaysky <ink@unseen.parts> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows the assembly in entry.S to automatically keep in sync with
changes in the stack layout (struct pt_regs and struct switch_stack).
Cc: stable@vger.kernel.org Tested-by: Maciej W. Rozycki <macro@orcam.me.uk> Tested-by: Matt Turner <mattst88@gmail.com> Reviewed-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Ivan Kokshaysky <ink@unseen.parts> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When flushing the serial port's buffer, uart_flush_buffer() calls
kfifo_reset() but if there is an outstanding DMA transfer then the
completion function will consume data from the kfifo via
uart_xmit_advance(), underflowing and leading to ongoing DMA as the
driver tries to transmit another 2^32 bytes.
This is readily reproduced with serial-generic and amidi sending even
short messages as closing the device on exit will wait for the fifo to
drain and in the underflow case amidi hangs for 30 seconds on exit in
tty_wait_until_sent(). A trace of that gives:
Since the port lock is held in when the kfifo is reset in
uart_flush_buffer() and in __dma_tx_complete(), adding a flush_buffer
hook to adjust the outstanding DMA byte count is sufficient to avoid the
kfifo underflow.
The documentation of the __uart_read_properties() states that
->iotype member is always altered after the function call, but
the code doesn't do that in the case when use_defaults == false
and the value of reg-io-width is unsupported. Make sure the code
follows the documentation.
Note, the current users of the uart_read_and_validate_port_properties()
will fail and the change doesn't affect their behaviour, neither
users of uart_read_port_properties() will be affected since the
alteration happens there even in the current code flow.
Fixes: e894b6005dce ("serial: port: Introduce a common helper to read properties") Cc: stable <stable@kernel.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20250124161530.398361-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the ->iotype is always assigned to the UPIO_MEM when
the respective property is not found. However, this will not
support the cases when user wants to have UPIO_PORT to be set
or preserved. Support this scenario by checking ->iobase value
and default the ->iotype respectively.
Fixes: 1117a6fdc7c1 ("serial: 8250_of: Switch to use uart_read_port_properties()") Fixes: e894b6005dce ("serial: port: Introduce a common helper to read properties") Cc: stable <stable@kernel.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20250124161530.398361-2-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun reported the following race between fork() and cgroup.kill at [1].
Tejun:
I was looking at cgroup.kill implementation and wondering whether there
could be a race window. So, __cgroup_kill() does the following:
k1. Set CGRP_KILL.
k2. Iterate tasks and deliver SIGKILL.
k3. Clear CGRP_KILL.
The copy_process() does the following:
c1. Copy a bunch of stuff.
c2. Grab siglock.
c3. Check fatal_signal_pending().
c4. Commit to forking.
c5. Release siglock.
c6. Call cgroup_post_fork() which puts the task on the css_set and tests
CGRP_KILL.
The intention seems to be that either a forking task gets SIGKILL and
terminates on c3 or it sees CGRP_KILL on c6 and kills the child. However, I
don't see what guarantees that k3 can't happen before c6. ie. After a
forking task passes c5, k2 can take place and then before the forking task
reaches c6, k3 can happen. Then, nobody would send SIGKILL to the child.
What am I missing?
This is indeed a race. One way to fix this race is by taking
cgroup_threadgroup_rwsem in write mode in __cgroup_kill() as the fork()
side takes cgroup_threadgroup_rwsem in read mode from cgroup_can_fork()
to cgroup_post_fork(). However that would be heavy handed as this adds
one more potential stall scenario for cgroup.kill which is usually
called under extreme situation like memory pressure.
To fix this race, let's maintain a sequence number per cgroup which gets
incremented on __cgroup_kill() call. On the fork() side, the
cgroup_can_fork() will cache the sequence number locally and recheck it
against the cgroup's sequence number at cgroup_post_fork() site. If the
sequence numbers mismatch, it means __cgroup_kill() can been called and
we should send SIGKILL to the newly created task.
Starting with Rust 1.86.0 (to be released 2025-04-03), Clippy will have
a new lint, `doc_overindented_list_items` [1], which catches cases of
overindented list items.
The lint has been added by Yutaro Ohno, based on feedback from the kernel
[2] on a patch that fixed a similar case -- commit 0c5928deada1 ("rust:
block: fix formatting in GenDisk doc").
Clippy reports a few cases in the kernel, apart from the one already
fixed in the commit above. One is this one:
error: doc list item overindented
--> rust/kernel/rbtree.rs:1152:5
|
1152 | /// null, it is a pointer to the root of the [`RBTree`].
| ^^^^ help: try using ` ` (2 spaces)
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#doc_overindented_list_items
= note: `-D clippy::doc-overindented-list-items` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(clippy::doc_overindented_list_items)]`
Starting with Rust 1.85.0 (currently in beta, to be released 2025-02-20),
under some kernel configurations with `CONFIG_RUST_DEBUG_ASSERTIONS=y`,
one may trigger a new `objtool` warning:
rust/kernel.o: warning: objtool: _R...securityNtB2_11SecurityCtx8as_bytes()
falls through to next function _R...core3ops4drop4Drop4drop()
due to a call to the `noreturn` symbol:
core::panicking::assert_failed::<usize, usize>
Thus add it to the list so that `objtool` knows it is actually `noreturn`.
Do so matching with `strstr` since it is a generic.
See commit 56d680dd23c3 ("objtool/rust: list `noreturn` Rust functions")
for more details.
Cc: stable@vger.kernel.org # Needed in 6.12.y and 6.13.y only (Rust is pinned in older LTSs). Fixes: 56d680dd23c3 ("objtool/rust: list `noreturn` Rust functions") Reviewed-by: Gary Guo <gary@garyguo.net> Link: https://lore.kernel.org/r/20250112143951.751139-1-ojeda@kernel.org
[ Updated Cc: stable@ to include 6.13.y. - Miguel ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with Rust 1.85.0 (to be released 2025-02-20), `rustc` warns
[1] about disabling neon in the aarch64 hardfloat target:
warning: target feature `neon` cannot be toggled with
`-Ctarget-feature`: unsound on hard-float targets
because it changes float ABI
|
= note: this was previously accepted by the compiler but
is being phased out; it will become a hard error
in a future release!
= note: for more information, see issue #116344
<https://github.com/rust-lang/rust/issues/116344>
Thus, instead, use the softfloat target instead.
While trying it out, I found that the kernel sanitizers were not enabled
for that built-in target [2]. Upstream Rust agreed to backport
the enablement for the current beta so that it is ready for
the 1.85.0 release [3] -- thanks!
However, that still means that before Rust 1.85.0, we cannot switch
since sanitizers could be in use. Thus conditionally do so.
UEFI 2.11 introduced EFI_MEMORY_HOT_PLUGGABLE to annotate system memory
regions that are 'cold plugged' at boot, i.e., hot pluggable memory that
is available from early boot, and described as system RAM by the
firmware.
Existing loaders and EFI applications running in the boot context will
happily use this memory for allocating data structures that cannot be
freed or moved at runtime, and this prevents the memory from being
unplugged. Going forward, the new EFI_MEMORY_HOT_PLUGGABLE attribute
should be tested, and memory annotated as such should be avoided for
such allocations.
In the EFI stub, there are a couple of occurrences where, instead of the
high-level AllocatePages() UEFI boot service, a low-level code sequence
is used that traverses the EFI memory map and carves out the requested
number of pages from a free region. This is needed, e.g., for allocating
as low as possible, or for allocating pages at random.
While AllocatePages() should presumably avoid special purpose memory and
cold plugged regions, this manual approach needs to incorporate this
logic itself, in order to prevent the kernel itself from ending up in a
hot unpluggable region, preventing it from being unplugged.
So add the EFI_MEMORY_HOTPLUGGABLE macro definition, and check for it
where appropriate.
scripts/Makefile.clang was changed in the linked commit to move --target from
KBUILD_CFLAGS to KBUILD_CPPFLAGS, as that generally has a broader scope.
However that variable is not inspected by the userprogs logic,
breaking cross compilation on clang.
Use both variables to detect bitsize and target arguments for userprogs.
The Mediatek MT7922 WiFi device advertises FLR support, but it apparently
does not work, and all subsequent config reads return ~0:
pci 0000:01:00.0: [14c3:0616] type 00 class 0x028000 PCIe Endpoint
pciback 0000:01:00.0: not ready 65535ms after FLR; giving up
After an FLR, pci_dev_wait() waits for the device to become ready. Prior
to d591f6804e7e ("PCI: Wait for device readiness with Configuration RRS"),
it polls PCI_COMMAND until it is something other that PCI_POSSIBLE_ERROR
(~0). If it times out, pci_dev_wait() returns -ENOTTY and
__pci_reset_function_locked() tries the next available reset method.
Typically this is Secondary Bus Reset, which does work, so the MT7922 is
eventually usable.
After d591f6804e7e, if Configuration Request Retry Status Software
Visibility (RRS SV) is enabled, pci_dev_wait() polls PCI_VENDOR_ID until it
is something other than the special 0x0001 Vendor ID that indicates a
completion with RRS status.
When RRS SV is enabled, reads of PCI_VENDOR_ID should return either 0x0001,
i.e., the config read was completed with RRS, or a valid Vendor ID. On the
MT7922, it seems that all config reads after FLR return ~0 indefinitely.
When pci_dev_wait() reads PCI_VENDOR_ID and gets 0xffff, it assumes that's
a valid Vendor ID and the device is now ready, so it returns with success.
After pci_dev_wait() returns success, we restore config space and continue.
Since the MT7922 is not actually ready after the FLR, the restore fails and
the device is unusable.
We considered changing pci_dev_wait() to continue polling if a
PCI_VENDOR_ID read returns either 0x0001 or 0xffff. This "works" as it did
before d591f6804e7e, although we have to wait for the timeout and then fall
back to SBR. But it doesn't work for SR-IOV VFs, which *always* return
0xffff as the Vendor ID.
Mark Mediatek MT7922 WiFi devices to avoid the use of FLR completely. This
will cause fallback to another reset method, such as SBR.
In the US country code, to avoid including 6 GHz rules in the 5 GHz rules
list, the number of 5 GHz rules is set to a default constant value of 4
(REG_US_5G_NUM_REG_RULES). However, if there are more than 4 valid 5 GHz
rules, the current logic will bypass the legitimate 6 GHz rules.
For example, if there are 5 valid 5 GHz rules and 1 valid 6 GHz rule, the
current logic will only consider 4 of the 5 GHz rules, treating the last
valid rule as a 6 GHz rule. Consequently, the actual 6 GHz rule is never
processed, leading to the eventual disabling of 6 GHz channels.
To fix this issue, instead of hardcoding the value to 4, use a helper
function to determine the number of 6 GHz rules present in the 5 GHz rules
list and ignore only those rules.
The problem is that GCC expects 16-byte alignment of the incoming stack
since early 2004, as Maciej found out [1]:
Having actually dug speculatively I can see that the psABI was changed in
GCC 3.5 with commit e5e10fb4a350 ("re PR target/14539 (128-bit long double
improperly aligned)") back in Mar 2004, when the stack pointer alignment
was increased from 8 bytes to 16 bytes, and arch/alpha/kernel/entry.S has
various suspicious stack pointer adjustments, starting with SP_OFF which
is not a whole multiple of 16.
Also, as Magnus noted, "ALPHA Calling Standard" [2] required the same:
D.3.1 Stack Alignment
This standard requires that stacks be octaword aligned at the time a
new procedure is invoked.
However:
- the "normal" kernel stack is always misaligned by 8 bytes, thanks to
the odd number of 64-bit words in 'struct pt_regs', which is the very
first thing pushed onto the kernel thread stack;
- syscall, fault, interrupt etc. handlers may, or may not, receive aligned
stack depending on numerous factors.
Somehow we got away with it until recently, when we ended up with
a stack corruption in kernel/smp.c:smp_call_function_single() due to
its use of 32-byte aligned local data and the compiler doing clever
things allocating it on the stack.
This adds padding between the PAL-saved and kernel-saved registers
so that 'struct pt_regs' have an even number of 64-bit words.
This makes the stack properly aligned for most of the kernel
code, except two handlers which need special threatment.
Note: struct pt_regs doesn't belong in uapi/asm; this should be fixed,
but let's put this off until later.
The driver assumed that es58x_dev->udev->serial could never be NULL.
While this is true on commercially available devices, an attacker
could spoof the device identity providing a NULL USB serial number.
That would trigger a NULL pointer dereference.
Add a check on es58x_dev->udev->serial before accessing it.
Reported-by: yan kang <kangyan91@outlook.com> Reported-by: yue sun <samsun1006219@gmail.com> Closes: https://lore.kernel.org/linux-can/SY8P300MB0421E0013C0EBD2AA46BA709A1F42@SY8P300MB0421.AUSP300.PROD.OUTLOOK.COM/ Fixes: 9f06631c3f1f ("can: etas_es58x: export product information through devlink_ops::info_get()") Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://patch.msgid.link/20250204154859.9797-2-mailhol.vincent@wanadoo.fr Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The J1939 standard requires the transmission of messages of length 0.
For example proprietary messages are specified with a data length of 0
to 1785. The transmission of such messages is not possible. Sending
results in no error being returned but no corresponding can frame
being generated.
Enable the transmission of zero length J1939 messages. In order to
facilitate this two changes are necessary:
1) If the transmission of a new message is requested from user space
the message is segmented in j1939_sk_send_loop(). Let the segmentation
take into account zero length messages, do not terminate immediately,
queue the corresponding skb.
2) j1939_session_skb_get_by_offset() selects the next skb to transmit
for a session. Take into account that there might be zero length skbs
in the queue.
Signed-off-by: Alexander Hölzl <alexander.hoelzl@gmx.net> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://patch.msgid.link/20250205174651.103238-1-alexander.hoelzl@gmx.net Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Cc: stable@vger.kernel.org
[mkl: commit message rephrased] Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Runtime PM is enabled as one of the last steps of probe(), so all
earlier gotos to "exit_free_device" label were not correct and were
leading to unbalanced runtime PM disable depth.
Fixes: 6e2fe01dd6f9 ("can: c_can: move runtime PM enable/disable to c_can_platform") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://patch.msgid.link/20250112-syscon-phandle-args-can-v1-1-314d9549906f@linaro.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If skb allocation fails, the pointer to struct can_frame is NULL. This
is actually handled everywhere inside ctucan_err_interrupt() except for
the only place.
Add the missed NULL check.
Found by Linux Verification Center (linuxtesting.org) with SVACE static
analysis tool.
Fixes: 2dcb8e8782d8 ("can: ctucanfd: add support for CTU CAN FD open-source IP core - bus independent part.") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Pavel Pisa <pisa@cmp.felk.cvut.cz> Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Link: https://patch.msgid.link/20250114152138.139580-1-pchelkin@ispras.ru Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MeiG Smart SLM828 is an LTE-A CAT6 modem with the mPCIe form factor. The
"Cls=ff(vend.) Sub=10 Prot=02" and "Cls=ff(vend.) Sub=10 Prot=03"
interfaces respond to AT commands. Add these interfaces.
The product ID the modem uses is shared across multiple modems. Therefore,
add comments to describe which interface is used for which modem.
device_del() can lead to new work being scheduled in gadget->work
workqueue. This is observed, for example, with the dwc3 driver with the
following call stack:
device_del()
gadget_unbind_driver()
usb_gadget_disconnect_locked()
dwc3_gadget_pullup()
dwc3_gadget_soft_disconnect()
usb_gadget_set_state()
schedule_work(&gadget->work)
Move flush_work() after device_del() to ensure the workqueue is cleaned
up.
Fixes: 5702f75375aa9 ("usb: gadget: udc-core: move sysfs_notify() to a workqueue") Cc: stable <stable@kernel.org> Signed-off-by: Roy Luo <royluo@google.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20250204233642.666991-1-royluo@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we receive an initial fragment of size 8 bytes which specifies a wLength
of 1 byte (so the reassembled message is supposed to be 9 bytes long), and
we then receive a second fragment of size 9 bytes (which is not supposed to
happen), we currently wrongly bypass the fragment reassembly code but still
pass the pointer to the acm->notification_buffer to
acm_process_notification().
Make this less wrong by always going through fragment reassembly when we
expect more fragments.
Before this patch, receiving an overlong fragment could lead to `newctrl`
in acm_process_notification() being uninitialized data (instead of data
coming from the device).
If the first fragment is shorter than struct usb_cdc_notification, we can't
calculate an expected_size. Log an error and discard the notification
instead of reading lengths from memory outside the received data, which can
lead to memory corruption when the expected_size decreases between
fragments, causing `expected_size - acm->nb_index` to wrap.
This issue has been present since the beginning of git history; however,
it only leads to memory corruption since commit ea2583529cd1
("cdc-acm: reassemble fragmented notifications").
A mitigating factor is that acm_ctrl_irq() can only execute after userspace
has opened /dev/ttyACM*; but if ModemManager is running, ModemManager will
do that automatically depending on the USB device's vendor/product IDs and
its other interfaces.
Add Renesas R-Car D3 USB Download mode quirk and update comments
on all the other Renesas R-Car USB Download mode quirks to discern
them from each other. This follows R-Car Series, 3rd Generation
reference manual Rev.2.00 chapter 19.2.8 USB download mode .
Fixes: 6d853c9e4104 ("usb: cdc-acm: Add DISABLE_ECHO for Renesas USB Download mode") Cc: stable <stable@kernel.org> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20250209145708.106914-1-marek.vasut+renesas@mailbox.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cause of this error is that the device has two interfaces, and the
hub driver binds to interface 1 instead of interface 0, which is where
usb_hub_to_struct_hub() looks.
We can prevent the problem from occurring by refusing to accept hub
devices that violate the USB spec by having more than one
configuration or interface.
Reported-and-tested-by: Robert Morris <rtm@csail.mit.edu> Cc: stable <stable@kernel.org> Closes: https://lore.kernel.org/linux-usb/95564.1737394039@localhost/ Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/c27f3bf4-63d8-4fb5-ac82-09e3cd19f61c@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the MIDI jacks are configured correctly, and the MIDIStreaming
endpoint descriptors are filled with the correct information,
bNumEmbMIDIJack and bLength are set incorrectly in these descriptors.
This does not matter when the numbers of in and out ports are equal, but
when they differ the host will receive broken descriptors with
uninitialized stack memory leaking into the descriptor for whichever
value is smaller.
The precise meaning of "in" and "out" in the port counts is not clearly
defined and can be confusing. But elsewhere the driver consistently
uses this to match the USB meaning of IN and OUT viewed from the host,
so that "in" ports send data to the host and "out" ports receive data
from it.
Cc: stable <stable@kernel.org> Fixes: c8933c3f79568 ("USB: gadget: f_midi: allow a dynamic number of input and output ports") Signed-off-by: John Keeping <jkeeping@inmusicbrands.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20250130195035.3883857-1-jkeeping@inmusicbrands.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fastboot tool for communicating with Android bootloaders does not
work reliably with this device if USB 2 Link Power Management (LPM)
is enabled.
Various fastboot commands are affected, including the
following, which usually reproduces the problem within two tries:
fastboot getvar kernel
getvar:kernel FAILED (remote: 'GetVar Variable Not found')
This issue was hidden on many systems up until commit 63a1f8454962
("xhci: stored cached port capability values in one place") as the xhci
driver failed to detect USB 2 LPM support if USB 3 ports were listed
before USB 2 ports in the "supported protocol capabilities".
Adding the quirk resolves the issue. No drawbacks are expected since
the device uses different USB product IDs outside of fastboot mode, and
since fastboot commands worked before, until LPM was enabled on the
tested system by the aforementioned commit.
Based on a patch from Forest <forestix@nom.one> from which most of the
code and commit message is taken.
Teclast disk used on Huawei hisi platforms doesn't work well,
losing connectivity intermittently if LPM is enabled.
Add quirk disable LPM to resolve the issue.
When usb_control_msg is used in the get_bMaxPacketSize0 function, the
USB pipe does not include the endpoint device number. This can cause
failures when a usb hub port is reinitialized after encountering a bad
cable connection. As a result, the system logs the following error
messages:
usb usb2-port1: cannot reset (err = -32)
usb usb2-port1: Cannot enable. Maybe the USB cable is bad?
usb usb2-port1: attempt power cycle
usb 2-1: new high-speed USB device number 5 using ci_hdrc
usb 2-1: device descriptor read/8, error -71
The problem began after commit 85d07c556216 ("USB: core: Unite old
scheme and new scheme descriptor reads"). There
usb_get_device_descriptor was replaced with get_bMaxPacketSize0. Unlike
usb_get_device_descriptor, the get_bMaxPacketSize0 function uses the
macro usb_rcvaddr0pipe, which does not include the endpoint device
number. usb_get_device_descriptor, on the other hand, used the macro
usb_rcvctrlpipe, which includes the endpoint device number.
By modifying the get_bMaxPacketSize0 function to use usb_rcvctrlpipe
instead of usb_rcvaddr0pipe, the issue can be resolved. This change will
ensure that the endpoint device number is included in the USB pipe,
preventing reinitialization failures. If the endpoint has not set the
device number yet, it will still work because the device number is 0 in
udev.
Cc: stable <stable@kernel.org> Fixes: 85d07c556216 ("USB: core: Unite old scheme and new scheme descriptor reads") Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com> Reviewed-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20250203105840.17539-1-eichest@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LS7A EHCI controller doesn't have extended capabilities, so the EECP
(EHCI Extended Capabilities Pointer) field of HCCPARAMS register should
be 0x0, but it reads as 0xa0 now. This is a hardware flaw and will be
fixed in future, now just clear the EECP field to avoid error messages
on boot:
Some Renesas HCs require firmware upload to work, this is handled by the
xhci_pci_renesas driver. Other variants of those chips load firmware from
a SPI flash and are ready to work with xhci_pci alone.
A refactor merged in v6.12 broke the latter configuration so that users
are finding their hardware ignored by the normal driver and are forced to
enable the firmware loader which isn't really necessary on their systems.
Let xhci_pci work with those chips as before when the firmware loader is
disabled by kernel configuration.
Fixes: 25f51b76f90f ("xhci-pci: Make xhci-pci-renesas a proper modular driver") Cc: stable <stable@kernel.org> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219616 Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219726 Signed-off-by: Michal Pecio <michal.pecio@gmail.com> Tested-by: Nicolai Buchwitz <nb@tipi-net.de> Link: https://lore.kernel.org/r/20250128104529.58a79bfc@foxbook Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dwc2_hsotg_udc_start(), e.g. when binding composite driver, "of_node"
is set to hsotg->dev->of_node.
It causes errors when binding the gadget driver several times, on
stm32mp157c-ev1 board. Below error is seen:
"pin PA10 already requested by 49000000.usb-otg; cannot claim for gadget.0"
The first time, no issue is seen as when registering the driver, of_node
isn't NULL:
-> gadget_dev_desc_UDC_store
-> usb_gadget_register_driver_owner
-> driver_register
...
-> really_probe -> pinctrl_bind_pins (no effect)
Then dwc2_hsotg_udc_start() sets of_node.
The second time (stop the gadget, reconfigure it, then start it again),
of_node has been set, so the probing code tries to acquire pins for the
gadget. These pins are hold by the controller, hence the error.
So clear gadget.dev.of_node in udc_stop() routine to avoid the issue.
drivers/usb/gadget/udc/renesas_usb3.c: In function 'renesas_usb3_probe':
drivers/usb/gadget/udc/renesas_usb3.c:2638:73: warning: '%d'
directive output may be truncated writing between 1 and 11 bytes into a
region of size 6 [-Wformat-truncation=]
2638 | snprintf(usb3_ep->ep_name, sizeof(usb3_ep->ep_name), "ep%d", i);
^~~~~~~~~~~~~~~~~~~~~~~~ ^~ ^
The role switch registration and set_role() can happen in parallel as they
are invoked independent of each other. There is a possibility that a driver
might spend significant amount of time in usb_role_switch_register() API
due to the presence of time intensive operations like component_add()
which operate under common mutex. This leads to a time window after
allocating the switch and before setting the registered flag where the set
role notifications are dropped. Below timeline summarizes this behavior
Thread1 | Thread2
usb_role_switch_register() |
| |
---> allocate switch |
| |
---> component_add() | usb_role_switch_set_role()
| | |
| | --> Drop role notifications
| | since sw->registered
| | flag is not set.
| |
--->Set registered flag.|
To avoid this, set the registered flag early on in the switch register
API.
Fixes: b787a3e78175 ("usb: roles: don't get/set_role() when usb_role_switch is unregistered") Cc: stable <stable@kernel.org> Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20250206193950.22421-1-quic_eserrao@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a frequent timeout during controller enter/exit from halt state
after toggling the run_stop bit by SW. This timeout occurs when
performing frequent role switches between host and device, causing
device enumeration issues due to the timeout. This issue was not present
when USB2 suspend PHY was disabled by passing the SNPS quirks
(snps,dis_u2_susphy_quirk and snps,dis_enblslpm_quirk) from the DTS.
However, there is a requirement to enable USB2 suspend PHY by setting of
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY bits when controller starts
in gadget or host mode results in the timeout issue.
This commit addresses this timeout issue by ensuring that the bits
GUSB2PHYCFG.ENBLSLPM and GUSB2PHYCFG.SUSPHY are cleared before starting
the dwc3_gadget_run_stop sequence and restoring them after the
dwc3_gadget_run_stop sequence is completed.
The current implementation sets the wMaxPacketSize of bulk in/out
endpoints to 1024 bytes at the end of the f_midi_bind function. However,
in cases where there is a failure in the first midi bind attempt,
consider rebinding. This scenario may encounter an f_midi_bind issue due
to the previous bind setting the bulk endpoint's wMaxPacketSize to 1024
bytes, which exceeds the ep->maxpacket_limit where configured dwc3 TX/RX
FIFO's maxpacket size of 512 bytes for IN/OUT endpoints in support HS
speed only.
Here the term "rebind" in this context refers to attempting to bind the
MIDI function a second time in certain scenarios. The situations where
rebinding is considered include:
* When there is a failure in the first UDC write attempt, which may be
caused by other functions bind along with MIDI.
* Runtime composition change : Example : MIDI,ADB to MIDI. Or MIDI to
MIDI,ADB.
This commit addresses this issue by resetting the wMaxPacketSize before
endpoint claim. And here there is no need to reset all values in the usb
endpoint descriptor structure, as all members except wMaxPacketSize and
bEndpointAddress have predefined values.
This ensures that restores the endpoint to its expected configuration,
and preventing conflicts with value of ep->maxpacket_limit. It also
aligns with the approach used in other function drivers, which treat
endpoint descriptors as if they were full speed before endpoint claim.
The pages_touched field represents the number of subbuffers in the ring
buffer that have content that can be read. This is used in accounting of
"dirty_pages" and "buffer_percent" to allow the user to wait for the
buffer to be filled to a certain amount before it reads the buffer in
blocking mode.
The persistent buffer never updated this value so it was set to zero, and
this accounting would take it as it had no content. This would cause user
space to wait for content even though there's enough content in the ring
buffer that satisfies the buffer_percent.
The meta data for a mapped ring buffer contains an array of indexes of all
the subbuffers. The first entry is the reader page, and the rest of the
entries lay out the order of the subbuffers in how the ring buffer link
list is to be created.
The validator currently makes sure that all the entries are within the
range of 0 and nr_subbufs. But it does not check if there are any
duplicates.
While working on the ring buffer, I corrupted this array, where I added
duplicates. The validator did not catch it and created the ring buffer
link list on top of it. Luckily, the corruption was only that the reader
page was also in the writer path and only presented corrupted data but did
not crash the kernel. But if there were duplicates in the writer side,
then it could corrupt the ring buffer link list and cause a crash.
Create a bitmask array with the size of the number of subbuffers. Then
clear it. When walking through the subbuf array checking to see if the
entries are within the range, test if its bit is already set in the
subbuf_mask. If it is, then there is duplicates and fail the validation.
If not, set the corresponding bit and continue.
Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Vincent Donnefort <vdonnefort@google.com> Link: https://lore.kernel.org/20250214102820.7509ddea@gandalf.local.home Fixes: c76883f18e59b ("ring-buffer: Add test if range of boot buffer is valid") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
But virt_to_page() does not work with vmap()'d memory which is what the
persistent ring buffer has. It is rather trivial to allow this, but for
now just disable mmap() of instances that have their ring buffer from the
reserve_mem option.
If an mmap() is performed on a persistent buffer it will return -ENODEV
just like it would if the .mmap field wasn't defined in the
file_operations structure.
Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Vincent Donnefort <vdonnefort@google.com> Link: https://lore.kernel.org/20250214115547.0d7287d3@gandalf.local.home Fixes: 9b7bdf6f6ece6 ("tracing: Have trace_printk not use binary prints if boot buffer") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory mapping the tracing ring buffer will disable resizing the buffer.
But if there's an error in the memory mapping like an invalid parameter,
the function exits out without re-enabling the resizing of the ring
buffer, preventing the ring buffer from being resized after that.
Explicitly clear DEBUGCTL.LBR when a CPU is starting, prior to purging the
LBR MSRs themselves, as at least one system has been found to transfer
control to the kernel with LBRs enabled (it's unclear whether it's a BIOS
flaw or a CPU goof). Because the kernel preserves the original DEBUGCTL,
even when toggling LBRs, leaving DEBUGCTL.LBR as is results in running
with LBRs enabled at all times.
The EAX of the CPUID Leaf 023H enumerates the mask of valid sub-leaves.
To tell the availability of the sub-leaf 1 (enumerate the counter mask),
perf should check the bit 1 (0x2) of EAS, rather than bit 0 (0x1).
The error is not user-visible on bare metal. Because the sub-leaf 0 and
the sub-leaf 1 are always available. However, it may bring issues in a
virtualization environment when a VMM only enumerates the sub-leaf 0.
Introduce the cpuid35_e?x to replace the macros, which makes the
implementation style consistent.
Fixes: eb467aaac21e ("perf/x86/intel: Support Architectural PerfMon Extension leaf") Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20250129154820.3755948-3-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When preparing vmcb02 for nested VMRUN (or state restore), "enter" guest
mode prior to initializing the MMU for nested NPT so that guest_mode is
set in the MMU's role. KVM's model is that all L2 MMUs are tagged with
guest_mode, as the behavior of hypervisor MMUs tends to be significantly
different than kernel MMUs.
Practically speaking, the bug is relatively benign, as KVM only directly
queries role.guest_mode in kvm_mmu_free_guest_mode_roots() and
kvm_mmu_page_ad_need_write_protect(), which SVM doesn't use, and in paths
that are optimizations (mmu_page_zap_pte() and
shadow_mmu_try_split_huge_pages()).
And while the role is incorprated into shadow page usage, because nested
NPT requires KVM to be using NPT for L1, reusing shadow pages across L1
and L2 is impossible as L1 MMUs will always have direct=1, while L2 MMUs
will have direct=0.
Hoist the TLB processing and setting of HF_GUEST_MASK to the beginning
of the flow instead of forcing guest_mode in the MMU, as nothing in
nested_vmcb02_prepare_control() between the old and new locations touches
TLB flush requests or HF_GUEST_MASK, i.e. there's no reason to present
inconsistent vCPU state to the MMU.
Fixes: 69cb877487de ("KVM: nSVM: move MMU setup to nested_prepare_vmcb_control") Cc: stable@vger.kernel.org Reported-by: Yosry Ahmed <yosry.ahmed@linux.dev> Reviewed-by: Yosry Ahmed <yosry.ahmed@linux.dev> Link: https://lore.kernel.org/r/20250130010825.220346-1-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the conditional loading of hardware DR6 with the guest's DR6 value
out of the core .vcpu_run() loop to fix a bug where KVM can load hardware
with a stale vcpu->arch.dr6.
When the guest accesses a DR and host userspace isn't debugging the guest,
KVM disables DR interception and loads the guest's values into hardware on
VM-Enter and saves them on VM-Exit. This allows the guest to access DRs
at will, e.g. so that a sequence of DR accesses to configure a breakpoint
only generates one VM-Exit.
For DR0-DR3, the logic/behavior is identical between VMX and SVM, and also
identical between KVM_DEBUGREG_BP_ENABLED (userspace debugging the guest)
and KVM_DEBUGREG_WONT_EXIT (guest using DRs), and so KVM handles loading
DR0-DR3 in common code, _outside_ of the core kvm_x86_ops.vcpu_run() loop.
But for DR6, the guest's value doesn't need to be loaded into hardware for
KVM_DEBUGREG_BP_ENABLED, and SVM provides a dedicated VMCB field whereas
VMX requires software to manually load the guest value, and so loading the
guest's value into DR6 is handled by {svm,vmx}_vcpu_run(), i.e. is done
_inside_ the core run loop.
Unfortunately, saving the guest values on VM-Exit is initiated by common
x86, again outside of the core run loop. If the guest modifies DR6 (in
hardware, when DR interception is disabled), and then the next VM-Exit is
a fastpath VM-Exit, KVM will reload hardware DR6 with vcpu->arch.dr6 and
clobber the guest's actual value.
The bug shows up primarily with nested VMX because KVM handles the VMX
preemption timer in the fastpath, and the window between hardware DR6
being modified (in guest context) and DR6 being read by guest software is
orders of magnitude larger in a nested setup. E.g. in non-nested, the
VMX preemption timer would need to fire precisely between #DB injection
and the #DB handler's read of DR6, whereas with a KVM-on-KVM setup, the
window where hardware DR6 is "dirty" extends all the way from L1 writing
DR6 to VMRESUME (in L1).
L1's view:
==========
<L1 disables DR interception>
CPU 0/KVM-7289 [023] d.... 2925.640961: kvm_entry: vcpu 0
A: L1 Writes DR6
CPU 0/KVM-7289 [023] d.... 2925.640963: <hack>: Set DRs, DR6 = 0xffff0ff1
Reported-by: John Stultz <jstultz@google.com> Closes: https://lkml.kernel.org/r/CANDhNCq5_F3HfFYABqFGCA1bPd_%2BxgNj-iDQhH4tDk%2Bwi8iZZg%40mail.gmail.com Fixes: 375e28ffc0cf ("KVM: X86: Set host DR6 only on VMX and for KVM_DEBUGREG_WONT_EXIT") Fixes: d67668e9dd76 ("KVM: x86, SVM: isolate vcpu->arch.dr6 from vmcb->save.dr6") Cc: stable@vger.kernel.org Cc: Jim Mattson <jmattson@google.com> Tested-by: John Stultz <jstultz@google.com> Link: https://lore.kernel.org/r/20250125011833.3644371-1-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Advertise support for Hyper-V's SEND_IPI and SEND_IPI_EX hypercalls if and
only if the local API is emulated/virtualized by KVM, and explicitly reject
said hypercalls if the local APIC is emulated in userspace, i.e. don't rely
on userspace to opt-in to KVM_CAP_HYPERV_ENFORCE_CPUID.
Rejecting SEND_IPI and SEND_IPI_EX fixes a NULL-pointer dereference if
Hyper-V enlightenments are exposed to the guest without an in-kernel local
APIC:
Note, checking the sending vCPU is sufficient, as the per-VM irqchip_mode
can't be modified after vCPUs are created, i.e. if one vCPU has an
in-kernel local APIC, then all vCPUs have an in-kernel local APIC.
It malicious user provides a small pptable through sysfs and then
a bigger pptable, it may cause buffer overflow attack in function
smu_sys_set_pp_table().
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> Signed-off-by: Jiang Liu <gerry@linux.alibaba.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ELP worker needs to calculate new metric values for all neighbors
"reachable" over an interface. Some of the used metric sources require
locks which might need to sleep. This sleep is incompatible with the RCU
list iterator used for the recorded neighbors. The initial approach to work
around of this problem was to queue another work item per neighbor and then
run this in a new context.
Even when this solved the RCU vs might_sleep() conflict, it has a major
problems: Nothing was stopping the work item in case it is not needed
anymore - for example because one of the related interfaces was removed or
the batman-adv module was unloaded - resulting in potential invalid memory
accesses.
Directly canceling the metric worker also has various problems:
* cancel_work_sync for a to-be-deactivated interface is called with
rtnl_lock held. But the code in the ELP metric worker also tries to use
rtnl_lock() - which will never return in this case. This also means that
cancel_work_sync would never return because it is waiting for the worker
to finish.
* iterating over the neighbor list for the to-be-deactivated interface is
currently done using the RCU specific methods. Which means that it is
possible to miss items when iterating over it without the associated
spinlock - a behaviour which is acceptable for a periodic metric check
but not for a cleanup routine (which must "stop" all still running
workers)
The better approch is to get rid of the per interface neighbor metric
worker and handle everything in the interface worker. The original problems
are solved by:
* creating a list of neighbors which require new metric information inside
the RCU protected context, gathering the metric according to the new list
outside the RCU protected context
* only use rcu_trylock inside metric gathering code to avoid a deadlock
when the cancel_delayed_work_sync is called in the interface removal code
(which is called with the rtnl_lock held)
Cc: stable@vger.kernel.org Fixes: c833484e5f38 ("batman-adv: ELP - compute the metric based on the estimated throughput") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a temporary error happened in the evaluation of the neighbor throughput
information, then the invalid throughput result should not be stored in the
throughtput EWMA.
Cc: stable@vger.kernel.org Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reference counting is used to ensure that
batadv_hardif_neigh_node and batadv_hard_iface
are not freed before/during
batadv_v_elp_throughput_metric_update work is
finished.
But there isn't a guarantee that the hard if will
remain associated with a soft interface up until
the work is finished.
This fixes a crash triggered by reboot that looks
like this:
(the batadv_v_mesh_free call is misleading,
and does not actually happen)
I was able to make the issue happen more reliably
by changing hardif_neigh->bat_v.metric_work work
to be delayed work. This allowed me to track down
and confirm the fix.
Cc: stable@vger.kernel.org Fixes: c833484e5f38 ("batman-adv: ELP - compute the metric based on the estimated throughput") Signed-off-by: Andy Strohman <andrew@andrewstrohman.com>
[sven@narfation.org: prevent entering batadv_v_elp_get_throughput without
soft_iface] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC 15 introduces a regression in "= { 0 }" style initialization of
unions that Linux has depended on for eliminating uninitialized variable
contents. GCC does not seem likely to fix it[1], instead suggesting[2]
that affected projects start using -fzero-init-padding-bits=unions.
To avoid future surprises beyond just the current situation with unions,
enable -fzero-init-padding-bits=all when available (GCC 15+). This will
correctly zero padding bits in unions and structs that might have been
left uninitialized, and will make sure there is no immediate regression
in union initializations. As seen in the stackinit KUnit selftest union
cases, which were passing before, were failing under GCC 15:
not ok 18 test_small_start_old_zero
ok 29 test_small_start_dynamic_partial # SKIP XFAIL uninit bytes: 63
ok 32 test_small_start_assigned_dynamic_partial # SKIP XFAIL uninit bytes: 63
ok 67 test_small_start_static_partial # SKIP XFAIL uninit bytes: 63
ok 70 test_small_start_static_all # SKIP XFAIL uninit bytes: 56
ok 73 test_small_start_dynamic_all # SKIP XFAIL uninit bytes: 56
ok 82 test_small_start_assigned_static_partial # SKIP XFAIL uninit bytes: 63
ok 85 test_small_start_assigned_static_all # SKIP XFAIL uninit bytes: 56
ok 88 test_small_start_assigned_dynamic_all # SKIP XFAIL uninit bytes: 56
The above all now pass again with -fzero-init-padding-bits=all added.
This also fixes the following cases for struct initialization that had
been XFAIL until now because there was no compiler support beyond the
larger "-ftrivial-auto-var-init=zero" option:
ok 38 test_small_hole_static_all # SKIP XFAIL uninit bytes: 3
ok 39 test_big_hole_static_all # SKIP XFAIL uninit bytes: 124
ok 40 test_trailing_hole_static_all # SKIP XFAIL uninit bytes: 7
ok 42 test_small_hole_dynamic_all # SKIP XFAIL uninit bytes: 3
ok 43 test_big_hole_dynamic_all # SKIP XFAIL uninit bytes: 124
ok 44 test_trailing_hole_dynamic_all # SKIP XFAIL uninit bytes: 7
ok 58 test_small_hole_assigned_static_all # SKIP XFAIL uninit bytes: 3
ok 59 test_big_hole_assigned_static_all # SKIP XFAIL uninit bytes: 124
ok 60 test_trailing_hole_assigned_static_all # SKIP XFAIL uninit bytes: 7
ok 62 test_small_hole_assigned_dynamic_all # SKIP XFAIL uninit bytes: 3
ok 63 test_big_hole_assigned_dynamic_all # SKIP XFAIL uninit bytes: 124
ok 64 test_trailing_hole_assigned_dynamic_all # SKIP XFAIL uninit bytes: 7
All of the above now pass when built under GCC 15. Tests can be seen
with:
./tools/testing/kunit/kunit.py run stackinit --arch=x86_64 \
--make_option CC=gcc-15
Clang continues to fully initialize these kinds of variables[3] without
additional flags.
The Vexia EDU ATLA 10 tablet comes in 2 different versions with
significantly different mainboards. The only outward difference is that
the charging barrel on one is marked 5V and the other is marked 9V.
The 5V version mostly works with the BYTCR defaults, except that it is
missing a CHAN package in its ACPI tables and the default of using
SSP0-AIF2 is wrong, instead SSP0-AIF1 must be used. That and its jack
detect signal is not inverted as it usually is.
Add a DMI quirk for the 5V version to fix sound not working.
I got a syzbot report: slab-out-of-bounds Read in
orangefs_debug_write... several people suggested fixes,
I tested Al Viro's suggestion and made this patch.
Signed-off-by: Mike Marshall <hubcap@omnibond.com> Reported-by: syzbot+fc519d7875f2d9186c1f@syzkaller.appspotmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Setting and clearing CPU bits in the mm_cpumask is only ever done
by the CPU itself, from the context switch code or the TLB flush
code.
Synchronization is handled by switch_mm_irqs_off() blocking interrupts.
Sending TLB flush IPIs to CPUs that are in the mm_cpumask, but no
longer running the program causes a regression in the will-it-scale
tlbflush2 test. This test is contrived, but a large regression here
might cause a small regression in some real world workload.
Instead of always sending IPIs to CPUs that are in the mm_cpumask,
but no longer running the program, send these IPIs only once a second.
The rest of the time we can skip over CPUs where the loaded_mm is
different from the target mm.
Reported-by: kernel test roboto <oliver.sang@intel.com> Signed-off-by: Rik van Riel <riel@surriel.com> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: https://lore.kernel.org/r/20241204210316.612ee573@fangorn Closes: https://lore.kernel.org/oe-lkp/202411282207.6bd28eae-lkp@intel.com/ Signed-off-by: Sasha Levin <sashal@kernel.org>
The Vexia EDU ATLA 10 tablet comes in 2 different versions with
significantly different mainboards. The only outward difference is that
the charging barrel on one is marked 5V and the other is marked 9V.
Both ship with Android 4.4 as factory OS and have the usual broken DSDT
issues for x86 Android tablets.
Add a quirk to skip ACPI I2C client enumeration for the 5V version to
complement the existing quirk for the 9V version.
Since upstream commit 8bd76b3d3f3a ("gpio: sim: lock up configfs that an
instantiated device depends on"), rmdir for an active virtual devices
been prohibited.
Update gpio-sim selftest to align with the change.
Function xen_pin_page calls xen_pte_lock, which in turn grab page
table lock (ptlock). When locking, xen_pte_lock expect mm->page_table_lock
to be held before grabbing ptlock, but this does not happen when pinning
is caused by xen_mm_pin_all.
This commit addresses lockdep warning below, which shows up when
suspending a Xen VM.
There is a HW defect on Grace Hopper (GH) to support the
Multi-Instance GPU (MIG) feature [1] that necessiated the presence
of a 1G region carved out from the device memory and mapped as
uncached. The 1G region is shown as a fake BAR (comprising region 2 and 3)
to workaround the issue.
The Grace Blackwell systems (GB) differ from GH systems in the following
aspects:
1. The aforementioned HW defect is fixed on GB systems.
2. There is a usable BAR1 (region 2 and 3) on GB systems for the
GPUdirect RDMA feature [2].
This patch accommodate those GB changes by showing the 64b physical
device BAR1 (region2 and 3) to the VM instead of the fake one. This
takes care of both the differences.
Moreover, the entire device memory is exposed on GB as cacheable to
the VM as there is no carveout required.
NVIDIA's recently introduced Grace Blackwell (GB) Superchip is a
continuation with the Grace Hopper (GH) superchip that provides a
cache coherent access to CPU and GPU to each other's memory with
an internal proprietary chip-to-chip cache coherent interconnect.
There is a HW defect on GH systems to support the Multi-Instance
GPU (MIG) feature [1] that necessiated the presence of a 1G region
with uncached mapping carved out from the device memory. The 1G
region is shown as a fake BAR (comprising region 2 and 3) to
workaround the issue. This is fixed on the GB systems.
The presence of the fix for the HW defect is communicated by the
device firmware through the DVSEC PCI config register with ID 3.
The module reads this to take a different codepath on GB vs GH.
Scan through the DVSEC registers to identify the correct one and use
it to determine the presence of the fix. Save the value in the device's
nvgrace_gpu_pci_core_device structure.
name is char[64] where the size of clnt->cl_program->name remains
unknown. Invoking strcat() directly will also lead to potential buffer
overflow. Change them to strscpy() and strncat() to fix potential
issues.
Signed-off-by: Zichen Xie <zichenxie0106@gmail.com> Reviewed-by: Benjamin Coddington <bcodding@redhat.com> Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Definitions of ioread64 and iowrite64 macros in asm/io.h called by vfio
pci implementations are enclosed inside check for CONFIG_GENERIC_IOMAP.
They don't get defined if CONFIG_GENERIC_IOMAP is defined. Include
linux/io-64-nonatomic-lo-hi.h to define iowrite64 and ioread64 macros
when they are not defined. io-64-nonatomic-lo-hi.h maps the macros to
generic implementation in lib/iomap.c. The generic implementation does
64 bit rw if readq/writeq is defined for the architecture, otherwise it
would do 32 bit back to back rw.
Note that there are two versions of the generic implementation that
differs in the order the 32 bit words are written if 64 bit support is
not present. This is not the little/big endian ordering, which is
handled separately. This patch uses the lo followed by hi word ordering
which is consistent with current back to back implementation in the
vfio/pci code.
If the <kunit/platform_device.h> header is included in a test without
certain other headers, it produces compiler warnings like:
In file included from [...]
../include/kunit/platform_device.h:15:57: warning: ‘struct completion’
declared inside parameter list will not be visible outside of this
definition or declaration
15 | struct completion *x);
| ^~~~~~~~~~
Add a 'struct completion' forward declaration to resolve this.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202412241958.dbAImJsA-lkp@intel.com/ Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: David Gow <davidgow@google.com> Link: https://lore.kernel.org/r/20241213180841.3023843-1-briannorris@chromium.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the B0 revision, the RTS pin remains high due to incorrect hardware
mapping. To address this issue, enable auto-direction control with the
RTS bit in ADCL_CFG_REG. This configuration ensures that the RTS pin
goes low when the terminal is opened and high when the terminal is
closed. Additionally, we reset the step counter for Rx and Tx engines
by writing into FRAC_DIV_CFG_REG.
parport_serial driver uses subset of WCH IDs that are present in 8250_pci.
Share them via pci_ids.h and switch parport_serial to use defined constants.
There are two sites of the same brand: wch.cn and wch-ic.com.
They are property of the same company, but it appears that they
managed to get two different PCI vendor IDs. Rename them accordingly
using standard pattern, i.e. PCI_VENDOR_ID_...
While at it, move to PCI_VDEVICE() in the ID tables.
If either SIGINT is received twice, or after a SIGALRM (that is, after
timerlat was supposed to stop), abort processing events currently left
in the tracefs buffer and exit immediately.
This allows the user to exit rtla without waiting for processing all
events, should that take longer than wanted, at the cost of not
processing all samples.
Cc: John Kacur <jkacur@redhat.com> Cc: Luis Goncalves <lgoncalv@redhat.com> Cc: Gabriele Monaco <gmonaco@redhat.com> Link: https://lore.kernel.org/20250116144931.649593-6-tglozar@redhat.com Signed-off-by: Tomas Glozar <tglozar@redhat.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If either SIGINT is received twice, or after a SIGALRM (that is, after
timerlat was supposed to stop), abort processing events currently left
in the tracefs buffer and exit immediately.
This allows the user to exit rtla without waiting for processing all
events, should that take longer than wanted, at the cost of not
processing all samples.
Cc: John Kacur <jkacur@redhat.com> Cc: Luis Goncalves <lgoncalv@redhat.com> Cc: Gabriele Monaco <gmonaco@redhat.com> Link: https://lore.kernel.org/20250116144931.649593-5-tglozar@redhat.com Signed-off-by: Tomas Glozar <tglozar@redhat.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, this does not cause any issues, but I believe it is necessary to
set bsg_queue to NULL after removing it to prevent potential use-after-free
(UAF) access.
Add Microchip parts to the Device ID table so the driver supports PCI100x
devices.
Add a new macro to quirk the Microchip Switchtec PCI100x parts to allow DMA
access via NTB to work when the IOMMU is turned on.
PCI100x family has 6 variants; each variant is designed for different
application usages, different port counts and lane counts:
PCI1001 has 1 x4 upstream port and 3 x4 downstream ports
PCI1002 has 1 x4 upstream port and 4 x2 downstream ports
PCI1003 has 2 x4 upstream ports, 2 x2 upstream ports, and 2 x2
downstream ports
PCI1004 has 4 x4 upstream ports
PCI1005 has 1 x4 upstream port and 6 x2 downstream ports
PCI1006 has 6 x2 upstream ports and 2 x2 downstream ports
[Historical note: these parts use PCI_VENDOR_ID_EFAR (0x1055), from EFAR
Microsystems, which was acquired in 1996 by Standard Microsystems Corp,
which was acquired by Microchip Technology in 2012. The PCI-SIG confirms
that Vendor ID 0x1055 is assigned to Microchip even though it's not
visible via https://pcisig.com/membership/member-companies]
Apparently the Raptor Lake-P reference firmware configures the PIO log size
correctly, but some vendor BIOSes, including at least ASUSTeK COMPUTER INC.
Zenbook UX3402VA_UX3402VA, do not.
Apply the quirk for Raptor Lake-P. This prevents kernel complaints like:
DPC: RP PIO log size 0 is invalid
and also enables the DPC driver to dump the RP PIO Log registers when DPC
is triggered.
Note that the bug report also mentions 8086:a76e, which has been already
added by 627c6db20703 ("PCI/DPC: Quirk PIO log size for Intel Raptor Lake
Root Ports").
syzbot report a null-ptr-deref in vidtv_mux_stop_thread. [1]
If dvb->mux is not initialized successfully by vidtv_mux_init() in the
vidtv_start_streaming(), it will trigger null pointer dereference about mux
in vidtv_mux_stop_thread().
Adjust the timing of streaming initialization and check it before
stopping it.
Reported-by: syzbot+5e248227c80a3be8e96a@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=5e248227c80a3be8e96a Signed-off-by: Edward Adam Davis <eadavis@qq.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for the Kurokesu C1 PRO camera. This camera experiences the
same issues faced by the Sonix Technology Co. 292A IPC AR0330. As such,
enable the UVC_QUIRK_MJPEG_NO_EOF quirk for this device to prevent
frames from being erroneously dropped.
The Sonix Technology Co. 292A camera (which uses an AR0330 sensor), can
produce MJPEG and H.264 streams concurrently. When doing so, it drops
the last packets of MJPEG frames every time the H.264 stream generates a
key frame. Set the UVC_QUIRK_MJPEG_NO_EOF quirk to work around the
issue.
Some cameras, such as the Sonix Technology Co. 292A, exhibit issues when
running two parallel streams, causing USB packets to be dropped when an
H.264 stream posts a keyframe while an MJPEG stream is running
simultaneously. This occasionally causes the driver to erroneously
output two consecutive JPEG images as a single frame.
To fix this, we inspect the buffer, and trigger a new frame when we
find an SOI.
The imx219/imx708 sensors frequently generate a single corrupt frame
(image or embedded data) when the sensor first starts. This can either
be a missing line, or invalid samples within the line. This only occurrs
using the upstream Unicam kernel driver.
Disabling trigger mode elimiates this corruption. Since trigger mode is
a legacy feature copied from the firmware driver and not expected to be
needed, remove it. Tested on the Raspberry Pi cameras and shows no ill
effects.
It appears that do_div() once more gets confused by a complex
expression that ends up not quite being constant despite
__builtin_constant_p() thinking it is:
Add a glue code for the MIPI I3C HCI on PCI bus with Intel Panther Lake
I3C controller PCI IDs.
MIPI I3C HCI on Intel platforms has additional logic around the MIPI I3C
HCI core logic. Those together create so called I3C slice on PCI bus.
Intel specific initialization code does a reset cycle to the I3C slice
before probing the MIPI I3C HCI part.
MIPI I3C HCI on Intel hardware requires a quirk where ring needs to stop
and set to run again after resuming the halted controller. This is not
expected from the MIPI I3C HCI specification and is Intel specific.
Add this quirk to generic aborted transfer handling and execute it only
when ring is not in running state after a transfer error and attempted
controller resume. This is the case on Intel hardware.
It is not fully clear to me what is the ring running state in generic
hardware in such case. I would expect if ring is not running, then stop
request is a no-op and run request is either required or does the same
what controller resume would do.
When using touchscreen and framebuffer, Nokia 770 crashes easily with:
BUG: scheduling while atomic: irq/144-ads7846/82/0x00010000
Modules linked in: usb_f_ecm g_ether usb_f_rndis u_ether libcomposite configfs omap_udc ohci_omap ohci_hcd
CPU: 0 UID: 0 PID: 82 Comm: irq/144-ads7846 Not tainted 6.12.7-770 #2
Hardware name: Nokia 770
Call trace:
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x54/0x5c
dump_stack_lvl from __schedule_bug+0x50/0x70
__schedule_bug from __schedule+0x4d4/0x5bc
__schedule from schedule+0x34/0xa0
schedule from schedule_preempt_disabled+0xc/0x10
schedule_preempt_disabled from __mutex_lock.constprop.0+0x218/0x3b4
__mutex_lock.constprop.0 from clk_prepare_lock+0x38/0xe4
clk_prepare_lock from clk_set_rate+0x18/0x154
clk_set_rate from sossi_read_data+0x4c/0x168
sossi_read_data from hwa742_read_reg+0x5c/0x8c
hwa742_read_reg from send_frame_handler+0xfc/0x300
send_frame_handler from process_pending_requests+0x74/0xd0
process_pending_requests from lcd_dma_irq_handler+0x50/0x74
lcd_dma_irq_handler from __handle_irq_event_percpu+0x44/0x130
__handle_irq_event_percpu from handle_irq_event+0x28/0x68
handle_irq_event from handle_level_irq+0x9c/0x170
handle_level_irq from generic_handle_domain_irq+0x2c/0x3c
generic_handle_domain_irq from omap1_handle_irq+0x40/0x8c
omap1_handle_irq from generic_handle_arch_irq+0x28/0x3c
generic_handle_arch_irq from call_with_stack+0x1c/0x24
call_with_stack from __irq_svc+0x94/0xa8
Exception stack(0xc5255da0 to 0xc5255de8)
5da0: 00000001c22fc6200000000000000000c08384a8c106fc0000000000c240c248
5dc0: c113a600c3f6ec300000000100000000c22fc620c5255df0c22fc620c0279a94
5de0: 60000013ffffffff
__irq_svc from clk_prepare_lock+0x4c/0xe4
clk_prepare_lock from clk_get_rate+0x10/0x74
clk_get_rate from uwire_setup_transfer+0x40/0x180
uwire_setup_transfer from spi_bitbang_transfer_one+0x2c/0x9c
spi_bitbang_transfer_one from spi_transfer_one_message+0x2d0/0x664
spi_transfer_one_message from __spi_pump_transfer_message+0x29c/0x498
__spi_pump_transfer_message from __spi_sync+0x1f8/0x2e8
__spi_sync from spi_sync+0x24/0x40
spi_sync from ads7846_halfd_read_state+0x5c/0x1c0
ads7846_halfd_read_state from ads7846_irq+0x58/0x348
ads7846_irq from irq_thread_fn+0x1c/0x78
irq_thread_fn from irq_thread+0x120/0x228
irq_thread from kthread+0xc8/0xe8
kthread from ret_from_fork+0x14/0x28
As a quick fix, switch to a threaded IRQ which provides a stable system.
Commit ca61d6836e6f ("firmware: qcom: scm: fix a NULL-pointer
dereference") makes it explicit that qcom_scm_get_tzmem_pool() can
return NULL, therefore its users should handle this.
Make sure the device is being reset on driver exit whatever the reason
is, to keep the device aligned and allow it to close shared resources
(e.g. admin queue).
Reviewed-by: Firas Jahjah <firasj@amazon.com> Reviewed-by: Yonatan Nachum <ynachum@amazon.com> Signed-off-by: Michael Margolin <mrgolin@amazon.com> Link: https://patch.msgid.link/20241225131548.15155-1-mrgolin@amazon.com Reviewed-by: Gal Pressman <gal.pressman@linux.dev> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_OBJTOOL=y or CONFIG_DEBUG_INFO_BTF=y, parallel builds
show awkward "mkdir -p ..." logs.
$ make -j16
[ snip ]
mkdir -p /home/masahiro/ref/linux/tools/objtool && make O=/home/masahiro/ref/linux subdir=tools/objtool --no-print-directory -C objtool
mkdir -p /home/masahiro/ref/linux/tools/bpf/resolve_btfids && make O=/home/masahiro/ref/linux subdir=tools/bpf/resolve_btfids --no-print-directory -C bpf/resolve_btfids
Defining MAKEFLAGS=<value> on the command line wipes out command line
switches from the resultant MAKEFLAGS definition, even though the command
line switches are active. [1]
MAKEFLAGS puts all single-letter options into the first word, and that
word will be empty if no single-letter options were given. [2]
However, this breaks if MAKEFLAGS=<value> is given on the command line.
The tools/ and tools/% targets set MAKEFLAGS=<value> on the command
line, which breaks the following code in tools/scripts/Makefile.include:
short-opts := $(firstword -$(MAKEFLAGS))
If MAKEFLAGS really needs modification, it should be done through the
environment variable, as follows:
MAKEFLAGS=<value> $(MAKE) ...
That said, I question whether modifying MAKEFLAGS is necessary here.
The only flag we might want to exclude is --no-print-directory, as the
tools build system changes the working directory. However, people might
find the "Entering/Leaving directory" logs annoying.
With recent kernel, AMDGPU failed to resume after suspend on certain laptop.
Sample log:
-----------
Nov 14 11:52:19 Thinkbook kernel: iommu ivhd0: AMD-Vi: Event logged [ILLEGAL_DEV_TABLE_ENTRY device=0000:06:00.0 pasid=0x00000 address=0x135300000 flags=0x0080]
Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[0]: 7d90000000000003
Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[1]: 0000100103fc0009
Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[2]: 2000000117840013
Nov 14 11:52:19 Thinkbook kernel: AMD-Vi: DTE[3]: 0000000000000000
This is because in resume path, CNTRL[EPHEn] is not set. Fix this by
setting CNTRL[EPHEn] to 1 in resume path if EFR[EPHSUP] is set.
Note
May be better approach is to save the control register in suspend path
and restore it in resume path instead of trying to set indivisual
bits. We will have separate patch for that.
The gpiochip_get_ngpios() uses chip_*() macros to print messages.
However these macros rely on gpiodev to be initialised and set,
which is not the case when called via bgpio_init(). In such a case
the printing messages will crash on NULL pointer dereference.
Replace chip_*() macros by the respective dev_*() ones to avoid
such crash.
Now when we use scx_bpf_task_cgroup() in ops.tick() to get the cgroup of
the current task, the following error will occur:
scx_foo[3795244] triggered exit kind 1024:
runtime error (called on a task not being operated on)
The reason is that we are using SCX_CALL_OP() instead of SCX_CALL_OP_TASK()
when calling ops.tick(), which triggers the error during the subsequent
scx_kf_allowed_on_arg_tasks() check.
SCX_CALL_OP_TASK() was first introduced in commit 36454023f50b ("sched_ext:
Track tasks that are subjects of the in-flight SCX operation") to ensure
task's rq lock is held when accessing task's sched_group. Since ops.tick()
is marked as SCX_KF_TERMINAL and task_tick_scx() is protected by the rq
lock, we can use SCX_CALL_OP_TASK() to avoid the above issue. Similarly,
the same changes should be made for ops.disable() and ops.exit_task(), as
they are also protected by task_rq_lock() and it's safe to access the
task's task_group.
Fixes: 36454023f50b ("sched_ext: Track tasks that are subjects of the in-flight SCX operation") Signed-off-by: Chuyi Zhou <zhouchuyi@bytedance.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
