set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: Christian König <christian.koenig@amd.com> Acked-by: Jordan Lazare <Jordan.Lazare@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to use post-decrement to get the pci_map_page undone also for
i==0, and to avoid some very unpleasant behaviour if pci_map_page
failed already at i==0.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per DP spec, the source device should fall back to 18 bpp, VESA range
RGB when the sink capability is unknown. Fix the color depth
clamping. 18 bpp color depth should ensure full color range in automatic
mode.
The clamping has been HDMI specific since its introduction in
Signed-off-by: Rob Clark <robdclark@gmail.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>. Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value returned by sys_personality has type "long int".
It is saved to a variable of type "int", which is not a problem
yet because the type of task_struct->pesonality is "unsigned int".
The problem is the sign extension from "int" to "long int"
that happens on return from sys_sparc64_personality.
For example, a userspace call personality((unsigned) -EINVAL) will
result to any subsequent personality call, including absolutely
harmless read-only personality(0xffffffff) call, failing with
errno set to EINVAL.
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EDAC workqueue destruction is really fragile. We cancel delayed work
but if it is still running and requeues itself, we still go ahead and
destroy the workqueue and the queued work explodes when workqueue core
attempts to run it.
Make the destruction more robust by switching op_state to offline so
that requeuing stops. Cancel any pending work *synchronously* too.
commit 4956e10903fd ("ARM: 6244/1: mmci: add variant data and default
MCICLOCK support") added variant data for ARM, U300 and Ux500 variants.
The Nomadik NHK8815/8820 variant was erroneously labeled as a U300
variant, and when the proper Nomadik variant was later introduced in
commit 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik MMCI
variant") this was not fixes. Let's say this fixes the latter commit as
there was no proper Nomadik support until then.
Fixes: 34fd421349ff ("ARM: 7378/1: mmci: add support for the Nomadik...") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sdhci has a legacy facility to prevent runtime suspend if the
bus power is on. This is needed in cases where the power to
the card is dependent on the bus power. It is controlled by
a pair of functions: sdhci_runtime_pm_bus_on() and
sdhci_runtime_pm_bus_off(). These functions use a boolean
variable 'bus_on' to ensure changes are always paired.
There is an additional check for 'runtime_suspended' which is
the problem. In fact, its use is ill-conceived as the only
requirement for the logic is that 'on' and 'off' are paired,
which is actually broken by the check, for example if the bus
power is turned on during runtime resume. So remove the check.
The 'ocr' parameter passed to mmc_set_signal_voltage()
defines the power-on voltage used when power cycling
after a failure to set the voltage. However, in the
case of mmc_sdio_init_card(), the value passed has the
R4_18V_PRESENT flag set which is not valid for power-on
and results in an invalid vdd. Fix by passing the card's
ocr value which does not have the flag.
The posix_clock_poll function is supposed to return a bit mask of
POLLxxx values. However, in case the hardware has disappeared (due to
hot plugging for example) this code returns -ENODEV in a futile
attempt to throw an error at the file descriptor level. The kernel's
file_operations interface does not accept such error codes from the
poll method. Instead, this function aught to return POLLERR.
The value -ENODEV does, in fact, contain the POLLERR bit (and almost
all the other POLLxxx bits as well), but only by chance. This patch
fixes code to return a proper bit mask.
Credit goes to Markus Elfring for pointing out the suspicious
signed/unsigned mismatch.
Reported-by: Markus Elfring <elfring@users.sourceforge.net>
igned-off-by: Richard Cochran <richardcochran@gmail.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Julia Lawall <julia.lawall@lip6.fr> Link: http://lkml.kernel.org/r/1450819198-17420-1-git-send-email-richardcochran@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When there is an error copying a chunk dm-snapshot can incorrectly hold
associated bios indefinitely, resulting in hung IO.
The function copy_callback sets pe->error if there was error copying the
chunk, and then calls complete_exception. complete_exception calls
pending_complete on error, otherwise it calls commit_exception with
commit_callback (and commit_callback calls complete_exception).
The persistent exception store (dm-snap-persistent.c) assumes that calls
to prepare_exception and commit_exception are paired.
persistent_prepare_exception increases ps->pending_count and
persistent_commit_exception decreases it.
If there is a copy error, persistent_prepare_exception is called but
persistent_commit_exception is not. This results in the variable
ps->pending_count never returning to zero and that causes some pending
exceptions (and their associated bios) to be held forever.
Fix this by unconditionally calling commit_exception regardless of
whether the copy was successful. A new "valid" parameter is added to
commit_exception -- when the copy fails this parameter is set to zero so
that the chunk that failed to copy (and all following chunks) is not
recorded in the snapshot store. Also, remove commit_callback now that
it is merely a wrapper around pending_complete.
Fixes: 50dd842ad ("dm space map metadata: fix ref counting bug when bootstrapping a new space map") Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tda1004x was updating the properties cache before locking.
If the device is not locked, the data at the registers are just
random values with no real meaning.
This caused the driver to fail with libdvbv5, as such library
calls GET_PROPERTY from time to time, in order to return the
DVB stats.
Tested with a saa7134 card 78:
ASUSTeK P7131 Dual, vendor PCI ID: 1043:4862
v4l2-compliance sends a zeroed struct v4l2_streamparm in
v4l2-test-formats.cpp::testParmType(), and this results in a division by
0 in some gspca subdrivers:
Let's also get rid of the "cosmic ray protection" while we're at it.
Fixes: e9193059b1b3 "hostfs: fix races in dentry_name() and inode_name()" Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel checks the specified length and the provided amount of
data for CCWs and provides an incorrect length error if the size does
not match. Under z/VM with simulation activated the length may get
changed. Having the suppress length indication bit set is stated as
good CCW coding practice and avoids errors under z/VM.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The normalization pass in the sorting routine of the relative exception
table serves two purposes:
- it ensures that the address fields of the exception table entries are
fully ordered, so that no ambiguities arise between entries with
identical instruction offsets (i.e., when two instructions that are
exactly 8 bytes apart each have an exception table entry associated with
them)
- it ensures that the offsets of both the instruction and the fixup fields
of each entry are relative to their final location after sorting.
Commit eb608fb366de ("s390/exceptions: switch to relative exception table
entries") ported the relative exception table format from x86, but modified
the sorting routine to only normalize the instruction offset field and not
the fixup offset field. The result is that the fixup offset of each entry
will be relative to the original location of the entry before sorting,
likely leading to crashes when those entries are dereferenced.
We weren't accounting for the insertion of an inline extent item for the
symlink inode nor that we need to update the parent inode item (through
the call to btrfs_add_nondir()). So fix this by including two more
transaction units.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a symlink is successfully created it always has an inline extent
containing the source path. However if an error happens when creating
the symlink, we can leave in the subvolume's tree a symlink inode without
any such inline extent item - this happens if after btrfs_symlink() calls
btrfs_end_transaction() and before it calls the inode eviction handler
(through the final iput() call), the transaction gets committed and a
crash happens before the eviction handler gets called, or if a snapshot
of the subvolume is made before the eviction handler gets called. Sadly
we can't just avoid this by making btrfs_symlink() call
btrfs_end_transaction() after it calls the eviction handler, because the
later can commit the current transaction before it removes any items from
the subvolume tree (if it encounters ENOSPC errors while reserving space
for removing all the items).
So make send fail more gracefully, with an -EIO error, and print a
message to dmesg/syslog informing that there's an empty symlink inode,
so that the user can delete the empty symlink or do something else
about it.
Reported-by: Stephen R. van den Berg <srb@cuci.nl> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We hit this panic on a few of our boxes this week where we have an
ordered_extent with an NULL inode. We do an igrab() of the inode in writepages,
but weren't doing it in writepage which can be called directly from the VM on
dirty pages. If the inode has been unlinked then we could have I_FREEING set
which means igrab() would return NULL and we get this panic. Fix this by trying
to igrab in btrfs_writepage, and if it returns NULL then just redirty the page
and return AOP_WRITEPAGE_ACTIVATE; so the VM knows it wasn't successful. Thanks,
Signed-off-by: Josef Bacik <jbacik@fb.com> Reviewed-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like oversight, call brelse() when checksum fails. Further down the
code, in the non error path, we do call brelse() and so we don't see
brelse() in the goto error paths.
Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
recordmcount edits the file in-place, which can cause problems when
using ccache in hardlink mode. Arrange for recordmcount to break a
hardlinked object.
Intel RAPL initialized on several systems where the BIOS lock bit (msr
0x610, bit 63) was set. This occured because the return value of
rapl_read_data_raw() was being checked, rather than the value of the variable
passed in, locked.
This patch properly implments the rapl_read_data_raw() call to check the
variable locked, and now the Intel RAPL driver outputs the warning:
intel_rapl: RAPL package 0 domain package locked by BIOS
and does not initialize for the package.
Signed-off-by: Prarit Bhargava <prarit@redhat.com> Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN found that our additional element processing scripts drop off
the end of the VPD page into unallocated space. The reason is that
not every element has additional information but our traversal
routines think they do, leading to them expecting far more additional
information than is present. Fix this by adding a gate to the
traversal routine so that it only processes elements that are expected
to have additional information (list is in SES-2 section 6.1.13.1:
Additional Element Status diagnostic page overview)
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple enclosure implementations (mostly USB) are allowed to return only
page 8 to every diagnostic query. That really confuses our
implementation because we assume the return is the page we asked for and
end up doing incorrect offsets based on bogus information leading to
accesses outside of allocated ranges. Fix that by checking the page
code of the return and giving an error if it isn't the one we asked for.
This should fix reported bugs with USB storage by simply refusing to
attach to enclosures that behave like this. It's also good defensive
practise now that we're starting to see more USB enclosures.
Reported-by: Andrea Gelmini <andrea.gelmini@gelma.net> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some users of rfkill, like NFC and cfg80211, use a dynamic name when
allocating rfkill, in those cases dev_name(). Therefore, the pointer
passed to rfkill_alloc() might not be valid forever, I specifically
found the case that the rfkill name was quite obviously an invalid
pointer (or at least garbage) when the wiphy had been renamed.
Fix this by making a copy of the rfkill name in rfkill_alloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is specifically for PCI support on the Versatile PB board using
a DT. Currently, the dynamic IRQ mapping is broken when using DTs. For
example, on QEMU, the SCSI driver is unable to request the IRQ. To fix
this issue, this patch replaces the current dynamic mechanism with a
static value as is done in the non-DT case.
If dm_btree_del()'s call to push_frame() fails, e.g. due to
btree_node_validator finding invalid metadata, the dm_btree_del() error
path must unlock all frames (which have active dm-bufio buffers) that
were pushed onto the del_stack.
Otherwise, dm_bufio_client_destroy() will BUG_ON() because dm-bufio
buffers have leaked, e.g.:
device-mapper: bufio: leaked buffer 3, hold count 1, list 0
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When applying block operations (BOPs) do not remove them from the
uncommitted BOP ring-buffer until after they've been applied -- in case
we recurse.
Also, perform BOP_INC operation, in dm_sm_metadata_create() and
sm_metadata_extend(), in terms of the uncommitted BOP ring-buffer rather
than using direct calls to sm_ll_inc().
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880
Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.
Because wakeups can (fundamentally) be late, a task might not be in
the expected state. Therefore testing against a task's state is racy,
and can yield false positives.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: oleg@redhat.com Fixes: 9067ac85d533 ("wake_up_process() should be never used to wakeup a TASK_STOPPED/TRACED task") Link: http://lkml.kernel.org/r/1448933660-23082-1-git-send-email-sasha.levin@oracle.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
root_domain::rto_mask allocated through alloc_cpumask_var()
contains garbage data, this may cause problems. For instance,
When doing pull_rt_task(), it may do useless iterations if
rto_mask retains some extra garbage bits. Worse still, this
violates the isolated domain rule for clustered scheduling
using cpuset, because the tasks(with all the cpus allowed)
belongs to one root domain can be pulled away into another
root domain.
The patch cleans the garbage by using zalloc_cpumask_var()
instead of alloc_cpumask_var() for root_domain::rto_mask
allocation, thereby addressing the issues.
Do the same thing for root_domain's other cpumask memembers:
dlo_mask, span, and online.
Signed-off-by: Xunlei Pang <xlpang@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1449057179-29321-1-git-send-email-xlpang@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com> Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sasha's found a NULL pointer dereference in the RDS connection code when
sending a message to an apparently unbound socket. The problem is caused
by the code checking if the socket is bound in rds_sendmsg(), which checks
the rs_bound_addr field without taking a lock on the socket. This opens a
race where rs_bound_addr is temporarily set but where the transport is not
in rds_bind(), leading to a NULL pointer dereference when trying to
dereference 'trans' in __rds_conn_create().
Vegard wrote a reproducer for this issue, so kindly ask him to share if
you're interested.
I cannot reproduce the NULL pointer dereference using Vegard's reproducer
with this patch, whereas I could without.
Complete earlier incomplete fix to CVE-2015-6937:
74e98eb08588 ("RDS: verify the underlying transport exists before creating a connection")
Reviewed-by: Vegard Nossum <vegard.nossum@oracle.com> Reviewed-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.
Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.
This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.
The virtio core uses a static ida named virtio_index_ida for
assigning index numbers to virtio devices during registration.
The ida core may allocate some internal idr cache layers and
an ida bitmap upon any ida allocation, and all these layers are
truely freed only upon the ida destruction. The virtio_index_ida
is not destroyed at present, leading to a memory leak when using
the virtio core as a module and atleast one virtio device is
registered and unregistered.
Fix this by invoking ida_destroy() in the virtio core module
exit.
Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not update the read stamp after swapping out the reader page from the
write buffer. If the reader page is swapped out of the buffer before an
event is written to it, then the read_stamp may get an out of date
timestamp, as the page timestamp is updated on the first commit to that
page.
rb_get_reader_page() only returns a page if it has an event on it, otherwise
it will return NULL. At that point, check if the page being returned has
events and has not been read yet. Then at that point update the read_stamp
to match the time stamp of the reader page.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
target_core_sbc's compare_and_write functionality suffers from taking
data at the wrong memory location when writing a CAW request to disk
when a SGL offset is non-zero.
This can happen with loopback and vhost-scsi fabric drivers when
SCF_PASSTHROUGH_SG_TO_MEM_NOALLOC is used to map existing user-space
SGL memory into COMPARE_AND_WRITE READ/WRITE payload buffers.
Rather than writing all-zeroes as instructed with the -D file, it
corrupts the data in the sector by splicing some of the original
bytes in. The page of the first entry of cmd->t_data_sg includes the
CDB, and sg->offset is set to a position past the CDB. I presume that
sg->offset is also the right choice to use for subsequent sglist
members.
Signed-off-by: Jan Engelhardt <jengelh@netitwork.de> Tested-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch addresses a race + use after free where the first
stage of COMPARE_AND_WRITE in compare_and_write_callback()
is rescheduled after the backend sends the secondary WRITE,
resulting in second stage compare_and_write_post() callback
completing in target_complete_ok_work() before the first
can return.
Because current code depends on checking se_cmd->se_cmd_flags
after return from se_cmd->transport_complete_callback(),
this results in first stage having SCF_COMPARE_AND_WRITE_POST
set, which incorrectly falls through into second stage CAW
processing code, eventually triggering a NULL pointer
dereference due to use after free.
To address this bug, pass in a new *post_ret parameter into
se_cmd->transport_complete_callback(), and depend upon this
value instead of ->se_cmd_flags to determine when to return
or fall through into ->queue_status() code for CAW.
The following test program from Dmitry can cause softlockups or RCU
stalls as it copies 1GB from tmpfs into eventfd and we don't have any
scheduling point at that path in sendfile(2) implementation:
int r1 = eventfd(0, 0);
int r2 = memfd_create("", 0);
unsigned long n = 1<<30;
fallocate(r2, 0, 0, n);
sendfile(r1, r2, 0, n);
Add cond_resched() into __splice_from_pipe() to fix the problem.
CC: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes STAR 9000953410: "perf callgraph profiling causing RCU stalls"
| perf record -g -c 15000 -e cycles /sbin/hackbench
|
| INFO: rcu_preempt self-detected stall on CPU
| 1: (1 GPs behind) idle=609/140000000000002/0 softirq=2914/2915 fqs=603
| Task dump for CPU 1:
in-kernel dwarf unwinder has a fast binary lookup and a fallback linear
search (which iterates thru each of ~11K entries) thus takes 2 orders of
magnitude longer (~3 million cycles vs. 2000). Routines written in hand
assembler lack dwarf info (as we don't support assembler CFI pseudo-ops
yet) fail the unwinder binary lookup, hit linear search, failing
nevertheless in the end.
However the linear search is pointless as binary lookup tables are created
from it in first place. It is impossible to have binary lookup fail while
succeed the linear search. It is pure waste of cycles thus removed by
this patch.
This manifested as RCU stalls / NMI watchdog splat when running
hackbench under perf with callgraph profiling. The triggering condition
was perf counter overflowing in routine lacking dwarf info (like memset)
leading to patheic 3 million cycle unwinder slow path and by the time it
returned new interrupts were already pending (Timer, IPI) and taken
rightaway. The original memset didn't make forward progress, system kept
accruing more interrupts and more unwinder delayes in a vicious feedback
loop, ultimately triggering the NMI diagnostic.
If md->signature == MAC_DRIVER_MAGIC and md->block_size == 1023, a single
512 byte sector would be read (secsize / 512). However the partition
structure would be located past the end of the buffer (secsize % 512).
Anytime a write operation is performed with Reliable Write flag enabled,
the eMMC device is enforced to bypass the cache and do a write to the
underling NVM device by Jedec specification; this causes a performance
penalty since write operations can't be optimized by the device cache.
In our tests, we replayed a typical mobile daily trace pattern and found
~9% overall time reduction in trace replay by using this patch. Also the
write ops within 4KB~64KB chunk size range get a 40~60% performance
improvement by using the patch (as this range of write chunks are the ones
affected by REQ_META).
This patch has been discussed in the Mobile & Embedded Linux Storage Forum
and it's the results of feedbacks from many people. We also checked with
fsdevl and f2fs mailing list developers that this change in the usage of
REQ_META is not affecting FS behavior and we got positive feedbacks.
Reporting here the feedbacks:
http://comments.gmane.org/gmane.linux.file-systems/97219
http://thread.gmane.org/gmane.linux.file-systems.f2fs/3178/focus=3183
Signed-off-by: Bruce Ford <bford@micron.com> Signed-off-by: Luca Porzio <lporzio@micron.com> Fixes: ce39f9d17c14 ("mmc: support packed write command for eMMC4.5 devices") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't set the SRB_FLAGS_QUEUE_ACTION_ENABLE flag since we are not specifying
tags. Without this, the qlogic driver doesn't work properly with storvsc.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is an issue on SMAP enabled CPUs and 32 bit apps running on 64 bit
OS. Do not access user memory from kernel code. The SMAP bit restricts
accessing user memory from kernel code.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not use PAGE_SIZE marco to calculate max_sectors per I/O
request. Driver code assumes PAGE_SIZE will be always 4096 which can
lead to wrongly calculated value if PAGE_SIZE is not 4096. This issue
was reported in Ubuntu Bugzilla Bug #1475166.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com> Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1c6c69525b40 ("genirq: Reject bogus threaded irq requests")
threaded IRQs without a primary handler need to be requested with
IRQF_ONESHOT, otherwise the request will fail.
scripts/coccinelle/misc/irqf_oneshot.cocci detected this issue.
Fixes: b5874f33bbaf ("wm831x_power: Use genirq") Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iomap[] array has PCIM_IOMAP_MAX (6) elements and not
DEVICE_COUNT_RESOURCE (16). This bug was found using a static checker.
It may be that the "if (!(mask & (1 << i)))" check means we never
actually go past the end of the array in real life.
Commit cb7323fffa85 ("lockd: create and use per-net NSM
RPC clients on MON/UNMON requests") introduced per-net
NSM RPC clients. Unfortunately this doesn't make any sense
without per-net nsm_handle.
E.g. the following scenario could happen
Two hosts (X and Y) in different namespaces (A and B) share
the same nsm struct.
1. nsm_monitor(host_X) called => NSM rpc client created,
nsm->sm_monitored bit set.
2. nsm_mointor(host-Y) called => nsm->sm_monitored already set,
we just exit. Thus in namespace B ln->nsm_clnt == NULL.
3. host X destroyed => nsm->sm_count decremented to 1
4. host Y destroyed => nsm_unmonitor() => nsm_mon_unmon() => NULL-ptr
dereference of *ln->nsm_clnt
So this could be fixed by making per-net nsm_handles list,
instead of global. Thus different net namespaces will not be able
share the same nsm_handle.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These async_XX functions are called from md/raid5 in an atomic
section, between get_cpu() and put_cpu(), so they must not sleep.
So use GFP_NOWAIT rather than GFP_IO.
Dan Williams writes: Longer term async_tx needs to be merged into md
directly as we can allocate this unmap data statically per-stripe
rather than per request.
Fixed: 7476bd79fc01 ("async_pq: convert to dmaengine_unmap_data") Reported-and-tested-by: Stanislav Samsonov <slava@annapurnalabs.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vt8500 clocksource driver declares itself as capable to handle the
minimum delay of 4 cycles by passing the value into
clockevents_config_and_register(). The vt8500_timer_set_next_event()
requires the passed cycles value to be at least 16. The impact is that
userspace hangs in nanosleep() calls with small delay intervals.
This problem is reproducible in Linux 4.2 starting from: c6eb3f70d448 ('hrtimer: Get rid of hrtimer softirq')
From Russell King, more detailed explanation:
"It's a speciality of the StrongARM/PXA hardware. It takes a certain
number of OSCR cycles for the value written to hit the compare registers.
So, if a very small delta is written (eg, the compare register is written
with a value of OSCR + 1), the OSCR will have incremented past this value
before it hits the underlying hardware. The result is, that you end up
waiting a very long time for the OSCR to wrap before the event fires.
So, we introduce a check in set_next_event() to detect this and return
-ETIME if the calculated delta is too small, which causes the generic
clockevents code to retry after adding the min_delta specified in
clockevents_config_and_register() to the current time value.
min_delta must be sufficient that we don't re-trip the -ETIME check - if
we do, we will return -ETIME, forward the next event time, try to set it,
return -ETIME again, and basically lock the system up. So, min_delta
must be larger than the check inside set_next_event(). A factor of two
was chosen to ensure that this situation would never occur.
The PXA code worked on PXA systems for years, and I'd suggest no one
changes this mechanism without access to a wide range of PXA systems,
otherwise they're risking breakage."
Cc: Russell King <linux@arm.linux.org.uk> Acked-by: Alexey Charkov <alchark@gmail.com> Signed-off-by: Roman Volkov <rvolkov@v1ros.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver
is already in the kernel, this node enables the controller support for
WM8650
synchronize_irq() waits for the interrupt thread to complete,
i.e. forever.
Solution is simple: Drop chip_bus_lock() before calling
synchronize_irq() as we do with the irq_desc lock. There is nothing to
be protected after the point where irq_desc lock has been released.
This adds chip_bus_lock/unlock() to the remove_irq() code path, but
that's actually correct in the case where remove_irq() is called on
such an interrupt. The current users of remove_irq() are not affected
as none of those interrupts is on a chip which requires buslock.
Reported-by: Fredrik Markström <fredrik.markstrom@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to be able to use pull_dl_task() from a callback, we need to
do away with the return value.
Since the return value indicates if we should reschedule, do this
inside the function. Since not all callers currently do this, this can
increase the number of reschedules due rt balancing.
Too many reschedules is not a correctness issues, too few are.
In order to be able to use pull_rt_task() from a callback, we need to
do away with the return value.
Since the return value indicates if we should reschedule, do this
inside the function. Since not all callers currently do this, this can
increase the number of reschedules due rt balancing.
Too many reschedules is not a correctness issues, too few are.
In order to remove dropping rq->lock from the
switched_{to,from}()/prio_changed() sched_class methods, run the
balance callbacks after it.
We need to remove dropping rq->lock because its buggy,
suppose using sched_setattr()/sched_setscheduler() to change a running
task from FIFO to OTHER.
By the time we get to switched_from_rt() the task is already enqueued
on the cfs runqueues. If switched_from_rt() does pull_rt_task() and
drops rq->lock, load-balancing can come in and move our task @p to
another rq.
The subsequent switched_to_fair() still assumes @p is on @rq and bad
things will happen.
By using balance callbacks we delay the load-balancing operations
{rt,dl}x{push,pull} until we've done all the important work and the
task is fully set up.
Furthermore, the balance callbacks do not know about @p, therefore
they cannot get confused like this.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: ktkhai@parallels.com Cc: rostedt@goodmis.org Cc: juri.lelli@gmail.com Cc: pang.xunlei@linaro.org Cc: oleg@redhat.com Cc: wanpeng.li@linux.intel.com Link: http://lkml.kernel.org/r/20150611124742.615343911@infradead.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Byungchul Park <byungchul.park@lge.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.
To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.
Fixes: 712f4aad406bb1 ("unix: properly account for FDs passed over unix sockets") Reported-by: David Herrmann <dh.herrmann@gmail.com> Cc: David Herrmann <dh.herrmann@gmail.com> Cc: Willy Tarreau <w@1wt.eu> Cc: Linus Torvalds <torvalds@linux-foundation.org> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.
Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.
This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Patrick Schaaf <netdev@bof.de> Tested-by: Patrick Schaaf <netdev@bof.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A test case is as the description says:
open(foobar, O_WRONLY);
sleep() --> reboot the server
close(foobar)
The bug is because in nfs4state.c in nfs4_reclaim_open_state() a few
line before going to restart, there is
clear_bit(NFS4CLNT_RECLAIM_NOGRACE, &state->flags).
NFS4CLNT_RECLAIM_NOGRACE is a flag for the client states not open
owner states. Value of NFS4CLNT_RECLAIM_NOGRACE is 4 which is the
value of NFS_O_WRONLY_STATE in nfs4_state->flags. So clearing it wipes
out state and when we go to close it, “call_close” doesn’t get set as
state flag is not set and CLOSE doesn’t go on the wire.
Using sendfile with below small program to get MD5 sums of some files,
it appear that big files (over 64kbytes with 4k pages system) get a
wrong MD5 sum while small files get the correct sum.
This program uses sendfile() to send a file to an AF_ALG socket
for hashing.
After investivation, it appears that sendfile() sends the files by blocks
of 64kbytes (16 times PAGE_SIZE). The problem is that at the end of each
block, the SPLICE_F_MORE flag is missing, therefore the hashing operation
is reset as if it was the end of the file.
This patch adds SPLICE_F_MORE to the flags when more data is pending.
Currently we don't check if the new MTU is valid or not and this allows
one to configure a smaller than minimum allowed by RFCs or even bigger
than interface own MTU, which is a problem as it may lead to packet
drops.
If you have a daemon like NetworkManager running, this may be exploited
by remote attackers by forging RA packets with an invalid MTU, possibly
leading to a DoS. (NetworkManager currently only validates for values
too small, but not for too big ones.)
The fix is just to make sure the new value is valid. That is, between
IPV6_MIN_MTU and interface's MTU.
Note that similar check is already performed at
ndisc_router_discovery(), for when kernel itself parses the RA.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: "Charles (Chas) Williams" <3chas3@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If either of the memory allocations in kvm_arch_vcpu_create() fail, the
vcpu which has been allocated and kvm_vcpu_init'd doesn't get uninit'd
in the error handling path. Add a call to kvm_vcpu_uninit() to fix this.
Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The immediate field of the CACHE instruction is signed, so ensure that
it gets sign extended by casting it to an int16_t rather than just
masking the low 16 bits.
Fixes: e685c689f3a8 ("KVM/MIPS32: Privileged instruction/target branch emulation.") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ASID restoration on guest resume should determine the guest execution
mode based on the guest Status register rather than bit 30 of the guest
PC.
Fix the two places in locore.S that do this, loading the guest status
from the cop0 area. Note, this assembly is specific to the trap &
emulate implementation of KVM, so it doesn't need to check the
supervisor bit as that mode is not implemented in the guest.
Fixes: b680f70fc111 ("KVM/MIPS32: Entry point for trampolining to...") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dentry that had been through (or into) __dentry_kill() might be seen
by shrink_dentry_list(); that's normal, it'll be taken off the shrink
list and freed if __dentry_kill() has already finished. The problem
is, its ->d_parent might be pointing to already freed dentry, so
lock_parent() needs to be careful.
We need to check that dentry hasn't already gone into __dentry_kill()
*and* grab rcu_read_lock() before dropping ->d_lock - the latter makes
sure that whatever we see in ->d_parent after dropping ->d_lock it
won't be freed until we drop rcu_read_lock().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lock_parent() very much on purpose does nested locking of dentries, and
is careful to maintain the right order (lock parent first). But because
it didn't annotate the nested locking order, lockdep thought it might be
a deadlock on d_lock, and complained.
Add the proper annotation for the inner locking of the child dentry to
make lockdep happy.
Introduced by commit 046b961b45f9 ("shrink_dentry_list(): take parent's
->d_lock earlier").
We have the same problem with ->d_lock order in the inner loop, where
we are dropping references to ancestors. Same solution, basically -
instead of using dentry_kill() we use lock_parent() (introduced in the
previous commit) to get that lock in a safe way, recheck ->d_count
(in case if lock_parent() has ended up dropping and retaking ->d_lock
and somebody managed to grab a reference during that window), trylock
the inode->i_lock and use __dentry_kill() to do the rest.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cause of livelocks there is that we are taking ->d_lock on
dentry and its parent in the wrong order, forcing us to use
trylock on the parent's one. d_walk() takes them in the right
order, and unfortunately it's not hard to create a situation
when shrink_dentry_list() can't make progress since trylock
keeps failing, and shrink_dcache_parent() or check_submounts_and_drop()
keeps calling d_walk() disrupting the very shrink_dentry_list() it's
waiting for.
Solution is straightforward - if that trylock fails, let's unlock
the dentry itself and take locks in the right order. We need to
stabilize ->d_parent without holding ->d_lock, but that's doable
using RCU. And we'd better do that in the very beginning of the
loop in shrink_dentry_list(), since the checks on refcount, etc.
would need to be redone anyway.
That deals with a half of the problem - killing dentries on the
shrink list itself. Another one (dropping their parents) is
in the next commit.
locking parent is interesting - it would be easy to do rcu_read_lock(),
lock whatever we think is a parent, lock dentry itself and check
if the parent is still the right one. Except that we need to check
that *before* locking the dentry, or we are risking taking ->d_lock
out of order. Fortunately, once the D1 is locked, we can check if
D2->d_parent is equal to D1 without the need to lock D2; D2->d_parent
can start or stop pointing to D1 only under D1->d_lock, so taking
D1->d_lock is enough. In other words, the right solution is
rcu_read_lock/lock what looks like parent right now/check if it's
still our parent/rcu_read_unlock/lock the child.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Result will be massaged to saner shape in the next commits. It is
ugly, no questions - the point of that one is to be a provably
equivalent transformation (and it might be worth splitting a bit
more).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can happen only when dentry_kill() is called with unlock_on_failure
equal to 0 - other callers had dentry pinned until the moment they've
got ->d_lock and DCACHE_DENTRY_KILLED is set only after lockref_mark_dead().
IOW, only one of three call sites of dentry_kill() might end up reaching
that code. Just move it there.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cxgb3_*_send() functions return NET_XMIT_ values, which are
positive integers values. So don't treat positive return values
as an error.
Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
[a pox on developers and maintainers who do not cc: stable for bug fixes like this - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corey Wright [Sun, 28 Feb 2016 08:42:39 +0000 (02:42 -0600)]
proc: Fix ptrace-based permission checks for accessing task maps
Modify mm_access() calls in fs/proc/task_mmu.c and fs/proc/task_nommu.c to
have the mode include PTRACE_MODE_FSCREDS so accessing /proc/pid/maps and
/proc/pid/pagemap is not denied to all users.
In backporting upstream commit caaee623 to pre-3.18 kernel versions it was
overlooked that mm_access() is used in fs/proc/task_*mmu.c as those calls
were removed in 3.18 (by upstream commit 29a40ace) and did not exist at the
time of the original commit.
This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a thin pool is being destroyed delayed work items are
cancelled using cancel_delayed_work(), which doesn't guarantee that on
return the delayed item isn't running. This can cause the work item to
requeue itself on an already destroyed workqueue. Fix this by using
cancel_delayed_work_sync() which guarantees that on return the work item
is not running anymore.
Fixes: 905e51b39a555 ("dm thin: commit outstanding data every second") Fixes: 85ad643b7e7e5 ("dm thin: add timeout to stop out-of-data-space mode holding IO forever") Signed-off-by: Nikolay Borisov <kernel@kyup.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When you take a metadata snapshot the btree roots for the mapping and
details tree need to have their reference counts incremented so they
persist for the lifetime of the metadata snap.
The roots being incremented were those currently written in the
superblock, which could possibly be out of date if concurrent IO is
triggering new mappings, breaking of sharing, etc.
Fix this by performing a commit with the metadata lock held while taking
a metadata snapshot.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A thin-pool that is in out-of-data-space (OODS) mode may transition back
to write mode -- without the admin adding more space to the thin-pool --
if/when blocks are released (either by deleting thin devices or
discarding provisioned blocks).
But as part of the thin-pool's earlier transition to out-of-data-space
mode the thin-pool may have set the 'error_if_no_space' flag to true if
the no_space_timeout expires without more space having been made
available. That implementation detail, of changing the pool's
error_if_no_space setting, needs to be reset back to the default that
the user specified when the thin-pool's table was loaded.
Otherwise we'll drop the user requested behaviour on the floor when this
out-of-data-space to write mode transition occurs.
Reported-by: Vivek Goyal <vgoyal@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Joe Thornber <ejt@redhat.com> Fixes: 2c43fd26e4 ("dm thin: fix missing out-of-data-space to write mode transition if blocks are released") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tapasweni Pathak reported that we do a kmalloc() in efi_call_phys_prolog()
on x86-64 while having interrupts disabled, which is a big no-no, as
kmalloc() can sleep.
Solve this by removing the irq disabling from the prolog/epilog calls
around EFI calls: it's unnecessary, as in this stage we are single
threaded in the boot thread, and we don't ever execute this from
interrupt contexts.
projects / thirdparty / kernel / stable.git / log
