The Stratix10 platform has an additional reset line, OCP(Open Core Protocol),
that also needs to get deasserted for the stmmac ethernet controller to work.
Thus we need to update the Kconfig to include ARCH_STRATIX10 in order to build
dwmac-socfpga.
Also, remove the redundant check for the reset controller pointer. The
reset driver already checks for the pointer and returns 0 if the pointer
is NULL.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if dev_get_valid_name failed, propagate its return code
and remove the setting err to ENODEV, it will be set to
0 again before dev_change_net_namespace exits.
Signed-off-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The array bpq_eth_addr is only used to get the size of an
address, whereas the bcast_addr is used to set the broadcast
address. This leads to a warning when using clang:
drivers/net/hamradio/bpqether.c:94:13: warning: variable 'bpq_eth_addr' is not
needed and will not be emitted [-Wunneeded-internal-declaration]
static char bpq_eth_addr[6];
^
Remove both variables and use the common eth_broadcast_addr
to set the broadcast address.
Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lockdep spotted that we are using rfs_h.lock in enic_get_rxnfc() without
initializing. rfs_h.lock is initialized in enic_open(). But ethtool_ops
can be called when interface is down.
Move enic_rfs_flw_tbl_init to enic_probe.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 18 PID: 1189 Comm: ethtool Not tainted 4.17.0-rc7-devel+ #27
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014
Call Trace:
dump_stack+0x85/0xc0
register_lock_class+0x550/0x560
? __handle_mm_fault+0xa8b/0x1100
__lock_acquire+0x81/0x670
lock_acquire+0xb9/0x1e0
? enic_get_rxnfc+0x139/0x2b0 [enic]
_raw_spin_lock_bh+0x38/0x80
? enic_get_rxnfc+0x139/0x2b0 [enic]
enic_get_rxnfc+0x139/0x2b0 [enic]
ethtool_get_rxnfc+0x8d/0x1c0
dev_ethtool+0x16c8/0x2400
? __mutex_lock+0x64d/0xa00
? dev_load+0x6a/0x150
dev_ioctl+0x253/0x4b0
sock_do_ioctl+0x9a/0x130
sock_ioctl+0x1af/0x350
do_vfs_ioctl+0x8e/0x670
? syscall_trace_enter+0x1e2/0x380
ksys_ioctl+0x60/0x90
__x64_sys_ioctl+0x16/0x20
do_syscall_64+0x5a/0x170
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not advertise DCBX_LLD_MANAGED capability i.e., do not allow
external agent to manage the dcbx/lldp negotiation. MFW acts as lldp agent
for qed* devices, and no other lldp agent is allowed to coexist with mfw.
Also updated a debug print, to not to display the redundant info.
Fixes: a1d8d8a51 ("qed: Add dcbnl support.") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid calling a SIMD fastpath handler if it is NULL. The check is needed
to handle an unlikely scenario where unsolicited interrupt is destined to
a PF in INTa mode.
Fixes: fe56b9e6a ("qed: Add module with basic common support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory for packet buffers need to be freed in the error paths as there is
no consumer (e.g., upper layer) for such packets and that memory will never
get freed.
The issue was uncovered when port was attacked with flood of isatap
packets, these are multicast packets hence were directed at all the PFs.
For foce PF, this meant they were routed to the ll2 module which in turn
drops such packets.
Fixes: 0a7fb11c ("qed: Add Light L2 support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Ariel Elior <ariel.elior@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't call function trace hook before setup percpu offset.
When entering secondary_start_kernel(), percpu offset has not
been initialized. So this lead hotplug malfunction.
Here is the flow to reproduce this bug:
dma_alloc_*() buffers might be exposed to userspace via mmap() call, so
they should be cleared on allocation. In case of IOMMU-based dma-mapping
implementation such buffer clearing was missing in the code path for
DMA_ATTR_FORCE_CONTIGUOUS flag handling, because dma_alloc_from_contiguous()
doesn't honor __GFP_ZERO flag. This patch fixes this issue. For more
information on clearing buffers allocated by dma_alloc_* functions,
see commit 6829e274a623 ("arm64: dma-mapping: always clear allocated
buffers").
Fixes: 44176bb38fa4 ("arm64: Add support for DMA_ATTR_FORCE_CONTIGUOUS to IOMMU") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now, we can call nfs_commit_inode() while holding the session slot,
which could lead to NFSv4 deadlocks. Ensure we only keep the slot if
the server returned a layout that we have to process.
Marking CPUs stopped by smp_send_stop as offline can cause warnings
due to cross-CPU wakeups. This trace was noticed on a busy system
running a sysrq+c crash test, after the injected crash:
This happens because firstly the CPU is not really offline in the
usual sense, processes and interrupts have not been migrated away.
Secondly smp_send_stop does not happen atomically on all CPUs, so
one CPU can have marked itself offline, while another CPU is still
running processes or interrupts which can affect the first CPU.
Fix this by just not marking the CPU as offline. It's more like
frozen in time, so offline does not really reflect its state properly
anyway. There should be nothing in the crash/panic path that walks
online CPUs and synchronously waits for them, so this change should
not introduce new hangs.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PID bitfield in descriptor should be set based on particular request
length, not based on EP's mc value. PID value can't be set to 0 even
request length is 0.
It happens when enable debug log, if set_alt() returns
USB_GADGET_DELAYED_STATUS and usb_composite_setup_continue()
is called before increasing count of @delayed_status,
so fix it by using spinlock of @cdev->lock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Tested-by: Jay Hsu <shih-chieh.hsu@mediatek.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If isoc split in transfer with no data (the length of DATA0
packet is zero), we can't simply return immediately. Because
the DATA0 can be the first transaction or the second transaction
for the isoc split in transaction. If the DATA0 packet with no
data is in the first transaction, we can return immediately.
But if the DATA0 packet with no data is in the second transaction
of isoc split in transaction sequence, we need to increase the
qtd->isoc_frame_index and giveback urb to device driver if needed,
otherwise, the MDATA packet will be lost.
A typical test case is that connect the dwc2 controller with an
usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
In the case, the isoc split in transaction sequence like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet (176 bytes)
- CSPLIT IN transaction
- DATA0 packet (0 byte)
This patch use both the length of DATA0 and qtd->isoc_split_offset
to check if the DATA0 is in the second transaction.
The commit 3bc04e28a030 ("usb: dwc2: host: Get aligned DMA in
a more supported way") rips out a lot of code to simply the
allocation of aligned DMA. However, it also introduces a new
issue when use isoc split in transfer.
In my test case, I connect the dwc2 controller with an usb hs
Hub (GL852G-12), and plug an usb fs audio device (Plantronics
headset) into the downstream port of Hub. Then use the usb mic
to record, we can find noise when playback.
It's because that the usb Hub uses an MDATA for the first
transaction and a DATA0 for the second transaction for the isoc
split in transaction. An typical isoc split in transaction sequence
like this:
- SSPLIT IN transaction
- CSPLIT IN transaction
- MDATA packet
- CSPLIT IN transaction
- DATA0 packet
The DMA address of MDATA (urb->dma) is always DWORD-aligned, but
the DMA address of DATA0 (urb->dma + qtd->isoc_split_offset) may
not be DWORD-aligned, it depends on the qtd->isoc_split_offset (the
length of MDATA). In my test case, the length of MDATA is usually
unaligned, this cause DATA0 packet transmission error.
This patch use kmem_cache to allocate aligned DMA buf for isoc
split in transaction. Note that according to usb 2.0 spec, the
maximum data payload size is 1023 bytes for each fs isoc ep,
and the maximum allowable interrupt data payload size is 64 bytes
or less for fs interrupt ep. So we set the size of object to be
1024 bytes in the kmem cache.
Tested-by: Gevorg Sahakyan <sahakyan@synopsys.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Minas Harutyunyan hminas@synopsys.com> Signed-off-by: William Wu <william.wu@rock-chips.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case when a hub is connected to DWC2 host
auto suspend occurs and host goes to
hibernation. When any device connected to hub
host hibernation exiting incorrectly.
- Added dwc2_hcd_rem_wakeup() function call to
exit from suspend state by remote wakeup.
- Increase timeout value for port suspend bit to be set.
Acked-by: Minas Harutyunyan <hminas@synopsys.com> Signed-off-by: Artur Petrosyan <arturp@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0198d7bb8a0c ("ASoC: omap-mcbsp: Convert to use the sdma-pcm
instead of omap-pcm") resulted in broken audio playback on OMAP1510
(discovered on Amstrad Delta).
When running on OMAP1510, omap-pcm used to obtain DMA offset from
snd_dmaengine_pcm_pointer_no_residue() based on DMA interrupt triggered
software calculations instead of snd_dmaengine_pcm_pointer() which
depended on residue value calculated from omap_dma_get_src_pos().
Similar code path is still available in now used
sound/soc/soc-generic-dmaengine-pcm.c but it is not triggered.
It was verified already before that omap_get_dma_src_pos() from
arch/arm/plat-omap/dma.c didn't work correctly for OMAP1510 - see
commit 1bdd7419910c ("ASoC: OMAP: fix OMAP1510 broken PCM pointer
callback") for details. Apparently the same applies to its successor,
omap_dma_get_src_pos() from drivers/dma/ti/omap-dma.c.
On the other hand, snd_dmaengine_pcm_pointer_no_residue() is described
as depreciated and discouraged for use in new drivers because of its
unreliable accuracy. However, it seems the only working option for
OPAM1510 now, as long as a software calculated residue is not
implemented as OMAP1510 fallback in omap-dma.
Using snd_dmaengine_pcm_pointer_no_residue() code path instead of
snd_dmaengine_pcm_pointer() in sound/soc/soc-generic-dmaengine-pcm.c
can be triggered in two ways:
- by passing pcm->flags |= SND_DMAENGINE_PCM_FLAG_NO_RESIDUE from
sound/soc/omap/sdma-pcm.c,
- by passing dma_caps.residue_granularity =
DMA_RESIDUE_GRANULARITY_DESCRIPTOR from DMA engine.
Let's do the latter.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently smatch warns of possible Spectre-V1 issue in ahci_led_store():
drivers/ata/libahci.c:1150 ahci_led_store() warn: potential spectre issue 'pp->em_priv' (local cap)
Userspace controls @pmp from following callchain:
em_message->store()
->ata_scsi_em_message_store()
-->ap->ops->em_store()
--->ahci_led_store()
After the mask+shift @pmp is effectively an 8b value, which is used to
index into an array of length 8, so sanitize the array index.
Run the completer task to post a work completion after processing
a memory registration or invalidate work request. This covers the
case where the memory registration or invalidate was the last work
request posted to the qp.
Signed-off-by: Vijay Immanuel <vijayi@attalasystems.com> Reviewed-by: Yonatan Cohen <yonatanc@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Mali-DP processors, the LAYER_FORMAT register contains fields
other than the format. These bits were unconditionally cleared when
setting the pixel format, whereas they should be preserved at their
reset values.
In the situation that DE and SE aren’t shared the same interrupt number,
the Global SE interrupts mask bit MASK_IRQ_EN in MASKIRQ must be set, or
else other mask bits will not work and no SE interrupt will occur. This
patch enables MASK_IRQ_EN for SE to fix this problem.
One needs to ensure that the crtcs are shutdown so that the
drm_crtc_state->connector_mask reflects that no connectors
are currently active. Further, it reduces the reference
count for each connector. This ensures that the connectors
and encoders can be cleanly removed either when _unbind
is called for the corresponding drivers or by
drm_mode_config_cleanup().
We need drm_atomic_helper_shutdown() to be called before
component_unbind_all() otherwise the connectors attached to the
component device will have the wrong reference count value and will not
be cleanly removed.
When vm test is skipped because of unmet dependencies and/or unsupported
configuration, it exits with error which is treated as a fail by the
Kselftest framework. This leads to false negative result even when the
test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When zram test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When user test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run. Add an explicit check
for module presence and return skip code if module isn't present.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When sysctl test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as
a fail by the Kselftest framework. This leads to false negative result
even when the test could not be run.
Change it to return kselftest skip code when a test gets skipped to
clearly report that the test could not be run.
Changed return code to kselftest skip code in skip error legs that check
requirements and module probe test error leg.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When static_keys test is skipped because of unmet dependencies and/or
unsupported configuration, it exits with error which is treated as a fail
by the Kselftest framework. This leads to false negative result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Added an explicit searches for test_static_key_base and test_static_keys
modules and return skip code if they aren't found to differentiate between
the failure to load the module condition and module not found condition.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
When pstore_post_reboot test gets skipped because of unmet dependencies
and/or unsupported configuration, it returns 0 which is treated as a pass
by the Kselftest framework. This leads to false positive result even when
the test could not be run.
Change it to return kselftest skip code when a test gets skipped to clearly
report that the test could not be run.
Kselftest framework SKIP code is 4 and the framework prints appropriate
messages to indicate that the test is skipped.
The helper module would be unloaded after nf_conntrack_helper_unregister,
so it may cause a possible panic caused by race.
nf_ct_iterate_destroy(unhelp, me) reset the helper of conntrack as NULL,
but maybe someone has gotten the helper pointer during this period. Then
it would panic, when it accesses the helper and the module was unloaded.
Take an example as following:
CPU0 CPU1
ctnetlink_dump_helpinfo
helper = rcu_dereference(help->helper);
unhelp
set helper as NULL
unload helper module
helper->to_nlattr(skb, ct);
As above, the cpu0 tries to access the helper and its module is unloaded,
then the panic happens.
It is a waste of memory to use a full "struct netns_sysctl_ipv6"
while only one pointer is really used, considering netns_sysctl_ipv6
keeps growing.
Also, since "struct netns_frags" has cache line alignment,
it is better to move the frags_hdr pointer outside, otherwise
we spend a full cache line for this pointer.
This saves 192 bytes of memory per netns.
Fixes: c038a767cd69 ("ipv6: add a new namespace for nf_conntrack_reasm") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On this system EC interrupt triggers constantly kicking devices out of
low power states and thus blocking power management. The system also has
a PCIe root port hosting Alpine Ridge Thunderbolt controller and it
never gets a chance to go to D3cold because of this.
Since the power button works the same regardless if EC interrupt is
enabled or not during s2idle, add a quirk for this machine that sets
ec_no_wakeup=true preventing spurious wakeups.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clocks have already been explicitly disabled and put as part of
remove() so the runtime suspend callback must not be run when balancing
the runtime PM usage count before returning.
Fixes: 16adc674d0d6 ("usb: dwc3: add generic OF glue layer") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct MIPI/PCIe/USB_HSIC's PGC offset based on
design RTL, the values in the Reference Manual
(Rev. 1, 01/2018 and the older ones) are incorrect.
The correct offset values should be as below:
0x800 ~ 0x83F: PGC for core0 of A7 platform;
0x840 ~ 0x87F: PGC for core1 of A7 platform;
0x880 ~ 0x8BF: PGC for SCU of A7 platform;
0xA00 ~ 0xA3F: PGC for fastmix/megamix;
0xC00 ~ 0xC3F: PGC for MIPI PHY;
0xC40 ~ 0xC7F: PGC for PCIe_PHY;
0xC80 ~ 0xCBF: PGC for USB OTG1 PHY;
0xCC0 ~ 0xCFF: PGC for USB OTG2 PHY;
0xD00 ~ 0xD3F: PGC for USB HSIC PHY;
Commit cc66b3038254 ("hwmon: (nct6775) Rework temperature source and label
handling") changed a loop limit from "data->temp_label_num - 1" to "32",
as part of moving from a string array to a bit mask. This results in the
following error, reported by UBSAN.
UBSAN: Undefined behaviour in drivers/hwmon/nct6775.c:4179:27
shift exponent 32 is too large for 32-bit type 'long unsigned int'
Similar to the original loop, the limit has to be one less than the
number of bits.
Fixes: cc66b3038254 ("hwmon: (nct6775) Rework temperature source and label handling") Reported-by: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de> Cc: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de> Tested-by: Paul Menzel <pmenzel+linux-hwmon@molgen.mpg.de> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
XPS13 9333 freeze kernel for about 500ms. Until Dell fixes it we need to
disable fan support for Dell XPS13 9333.
Via "force" module param fan support can be enabled.
Compared to other clients the Linux smb3 client ramps up
credits very slowly, taking more than 128 operations before a
maximum size write could be sent (since the number of credits
requested is only 2 per small operation, causing the credit
limit to grow very slowly).
This lack of credits initially would impact large i/o performance,
when large i/o is tried early before enough credits are built up.
Signed-off-by: Steve French <sfrench@gmail.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modern distroes increasingly make use of BPF programs. Default
Ubuntu 18.04 installation boots with a number of cgroup_skb
programs loaded.
test_offloads.py tries to check if programs and maps are not
leaked on error paths by confirming the list of programs on the
system is empty between tests.
Since we can no longer expect the system to have no BPF objects
at boot try to remember the programs and maps present at the start,
and skip those when scanning the system.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC built for arc*-*-linux has "-mmedium-calls" implicitly enabled by default
thus we don't see any problems during Linux kernel compilation.
----------------------------->8------------------------
arc-linux-gcc -mcpu=arc700 -Q --help=target | grep calls
-mlong-calls [disabled]
-mmedium-calls [enabled]
----------------------------->8------------------------
But if we try to use so-called Elf32 toolchain with GCC configured for
arc*-*-elf* then we'd see the following failure:
----------------------------->8------------------------
init/do_mounts.o: In function 'init_rootfs':
do_mounts.c:(.init.text+0x108): relocation truncated to fit: R_ARC_S21W_PCREL
against symbol 'unregister_filesystem' defined in .text section in fs/filesystems.o
arc-elf32-ld: final link failed: Symbol needs debug section which does not exist
make: *** [vmlinux] Error 1
----------------------------->8------------------------
That happens because neither "-mmedium-calls" nor "-mlong-calls" are enabled in
Elf32 GCC:
----------------------------->8------------------------
arc-elf32-gcc -mcpu=arc700 -Q --help=target | grep calls
-mlong-calls [disabled]
-mmedium-calls [disabled]
----------------------------->8------------------------
Now to make it possible to use Elf32 toolchain for building Linux kernel
we're explicitly add "-mmedium-calls" to CFLAGS.
And since we add "-mmedium-calls" to the global CFLAGS there's no point in
having per-file copies thus removing them.
Buffer overflow error should not occur, as mode_fixup() callback
filters pixel clock value and it should never exceed 600000. However,
current implementation is not obviously safe and relies on
implementation of mode_fixup().
Make 'i' variable never reach unsafe value in order to avoid buffer
overflow error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: bf1722ca ("drm/bridge/sii8620: rewrite hdmi start sequence") Signed-off-by: Maciej Purski <m.purski@samsung.com> Signed-off-by: Andrzej Hajda <a.hajda@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/1511341718-6974-1-git-send-email-m.purski@samsung.com Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before returning -EPERM we should release some resources, as already done
in the other error handling path of the function.
Fixes: d8f9cc328c88 ("IB/mlx4: Mark user MR as writable if actual virtual memory is writable") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation for the touchscreen-swapped-x-y property states that
swapping is done after inverting if both are used. RMI4 did it the other
way around, leading to inconsistent behavior with regard to other
touchscreens.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Nick Dyer <nick@shmanahar.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some RoCE specific code in qedr_modify_qp was run over an iWARP device
when running perftest benchmarks without the -R option.
The commit 3e44e0ee0893 ("IB/providers: Avoid null netdev check for RoCE")
exposed this. Dropping the check for NULL pointer on ndev in
qedr_modify_qp lead to a null pointer dereference when running over
iWARP. Before the code would identify ndev as being NULL and return an
error.
In rxe_send, when network_type is not RDMA_NETWORK_IPV4 or
RDMA_NETWORK_IPV6, skb is freed and -EINVAL is returned.
Then rxe_xmit_packet will return -EINVAL, too. In rxe_requester,
this skb is double freed.
In rxe_requester, kfree_skb is needed only after fill_packet fails.
So kfree_skb is moved from label err to test fill_packet.
Fixes: 5793b4652155 ("IB/rxe: remove unnecessary skb_clone in xmit") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events, the driver uses
a per CPU napi structure for this case. Some SoCs such as armada 3700
have a single interrupt for Ethernet events, the driver uses a global
napi structure for this case.
Current mvneta_config_rss() always operates the per cpu napi structure.
Fix it by operating a global napi for "single interrupt" case, and per
cpu napi structure for remaining cases.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com> Fixes: 2636ac3cc2b4 ("net: mvneta: Add network support for Armada 3700 SoC") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mvneta Ethernet driver is used on a few different Marvell SoCs.
Some SoCs have per cpu interrupts for Ethernet events. Some SoCs have
a single interrupt, independent of the CPU. The driver handles this by
having a per CPU napi structure when there are per CPU interrupts, and
a global napi structure when there is a single interrupt.
When the napi core calls mvneta_poll(), it passes the napi
instance. This was not being propagated through the call chain, and
instead the per-cpu napi instance was passed to napi_gro_receive()
call. This breaks when there is a single global napi instance.
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Fixes: 2636ac3cc2b4 ("net: mvneta: Add network support for Armada 3700 SoC") Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix tcf_unbind_filter missing in cls_matchall as this will trigger
WARN_ON() in cbq_destroy_class().
Fixes: fd62d9f5c575f ("net/sched: matchall: Fix configuration race") Reported-by: Li Shuang <shuali@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 79134e6ce2c9 ("net: do not create fallback tunnels for non-default namespaces") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd.
RTL8101/2/6E PCI Express Fast/Gigabit Ethernet controller [10ec:8136]
(rev 07)
Subsystem: ASUSTeK Computer Inc. RTL810xE PCI Express Fast
Ethernet controller [1043:200f]
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at e000 [size=256]
Memory at ef100000 (64-bit, non-prefetchable) [size=4K]
Memory at e0000000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
Kernel modules: r8169
Falling back to MSI fixes the issue.
Fixes: 6c6aa15fdea5 ("r8169: improve interrupt handling") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
req->sdiag_family is a user-controlled value that's used as an array
index. Sanitize it after the bounds check to avoid speculative
out-of-bounds array access.
This also protects the sock_is_registered() call, so this removes the
sanitize call there.
Fixes: e978de7a6d38 ("net: socket: Fix potential spectre v1 gadget in sock_is_registered") Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: konrad.wilk@oracle.com Cc: jamie.iles@oracle.com Cc: liran.alon@oracle.com Cc: stable@vger.kernel.org Signed-off-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was possible to directly leak the kernel address where the isdn_dev
structure pointer was stored. This is a kernel ASLR bypass for anyone
with access to the ioctl. The code had been present since the beginning
of git history, though this shouldn't ever be needed for normal operation,
therefore remove it.
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ 210.115454] Memory state around the buggy address:
[ 210.115460] ffff880107e17000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 210.115465] ffff880107e17080: fc fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb
[ 210.115469] >ffff880107e17100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 210.115472] ^
[ 210.115477] ffff880107e17180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 210.115481] ffff880107e17200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 210.115483] ==================================================================
And finally when BT_DBG() and ftrace was enabled it showed:
Only in the failed case, sco_sock_kill() gets called with the same sock
pointer two times. Add a check for SOCK_DEAD to avoid continue killing
a socket which has already been killed.
Make sure to disable clocks and deregister any exported partitions
before returning on late probe errors.
Note that since commit ee895ccdf776 ("misc: sram: fix enabled clock leak
on error path"), partitions are deliberately exported before enabling
the clock so we stick to that logic here. A follow up patch will address
this.
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[ 54.928108] dw8250_set_termios+0x162/0x170
[ 54.928114] serial8250_set_termios+0x17/0x20
[ 54.928117] uart_change_speed+0x64/0x160
[ 54.928119] uart_resume_port
...
So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.
We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.
Signed-off-by: Chen Hu <hu1.chen@intel.com> Fixes: 4e26b134bd17 ("serial: 8250_dw: clock rate handling for all ACPI platforms") Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@vger.kernel.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:
The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:
Every time I tried to upgrade my laptop from 3.10.x to 4.x I faced an
issue by which the fan would run at full speed upon resume. Bisecting
it showed me the issue was introduced in 3.17 by commit 821d6f0359b0
(ACPI / sleep: Do not save NVS for new machines to accelerate S3). This
code only affects machines built starting as of 2012, but this Asus
1025C laptop was made in 2012 and apparently needs the NVS data to be
saved, otherwise the CPU's thermal state is not properly reported on
resume and the fan runs at full speed upon resume.
Here's a very simple way to check if such a machine is affected :
# cat /sys/class/thermal/thermal_zone0/temp
55000
( now suspend, wait one second and resume )
# cat /sys/class/thermal/thermal_zone0/temp
0
(and after ~15 seconds the fan starts to spin)
Let's apply the same quirk as commit cbc00c13 (ACPI: save NVS memory
for Lenovo G50-45) and reuse the function it provides. Note that this
commit was already backported to 4.9.x but not 4.4.x.
Cc: 3.17+ <stable@vger.kernel.org> # 3.17+: requires cbc00c13 Signed-off-by: Willy Tarreau <w@1wt.eu> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device exposes AT, NMEA and DIAG ports in both USB configurations.
The patch explicitly ignores interfaces 0 and 1, as they're bound to
other drivers already; and also interface 6, which is a GNSS interface
for which we don't have a driver yet.
Signed-off-by: Movie Song <MovieSong@aten-itlab.cn> Cc: Johan Hovold <johan@kernel.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The portdata spinlock can be taken in interrupt context (via
sierra_outdat_callback()).
Disable interrupts when taking the portdata spinlock when discarding
deferred URBs during close to prevent a possible deadlock.
Fixes: 014333f77c0b ("USB: sierra: fix urb and memory leak on disconnect") Cc: stable <stable@vger.kernel.org> Signed-off-by: John Ogness <john.ogness@linutronix.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[ johan: amend commit message and add fixes and stable tags ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The endian conversions used in vxp_dma_read() and vxp_dma_write() are
superfluous and even wrong on big-endian machines, as inw() and outw()
already do conversions. Kill them.
snd_dma_alloc_pages_fallback() tries to allocate pages again when the
allocation fails with reduced size. But the first try actually
*increases* the size to power-of-two, which may give back a larger
chunk than the requested size. This confuses the callers, e.g. sgbuf
assumes that the size is equal or less, and it may result in a bad
loop due to the underflow and eventually lead to Oops.
The code of this function seems incorrectly assuming the usage of
get_order(). We need to decrease at first, then align to
power-of-two.
Reported-and-tested-by: he, bo <bo.he@intel.com> Reported-by: zhang jun <jun.zhang@intel.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One place in cs5535audio_build_dma_packets() does an extra conversion
via cpu_to_le32(); namely jmpprd_addr is passed to setup_prd() ops,
which writes the value via cs_writel(). That is, the callback does
the conversion by itself, and we don't need to convert beforehand.
The virmidi output trigger tries to parse the all available bytes and
process sequencer events as much as possible. In a normal situation,
this is supposed to be relatively short, but a program may give a huge
buffer and it'll take a long time in a single spin lock, which may
eventually lead to a soft lockup.
This patch simply adds a workaround, a cond_resched() call in the loop
if applicable. A better solution would be to move the event processor
into a work, but let's put a duct-tape quickly at first.
The endian conversions used in vx2_dma_read() and vx2_dma_write() are
superfluous and even wrong on big-endian machines, as inl() and outl()
already do conversions. Kill them.
Spotted by sparse, a warning like:
sound/pci/vx222/vx222_ops.c:278:30: warning: incorrect type in argument 1 (different base types)
AF_RXRPC has a keepalive message generator that generates a message for a
peer ~20s after the last transmission to that peer to keep firewall ports
open. The implementation is incorrect in the following ways:
(1) It mixes up ktime_t and time64_t types.
(2) It uses ktime_get_real(), the output of which may jump forward or
backward due to adjustments to the time of day.
(3) If the current time jumps forward too much or jumps backwards, the
generator function will crank the base of the time ring round one slot
at a time (ie. a 1s period) until it catches up, spewing out VERSION
packets as it goes.
Fix the problem by:
(1) Only using time64_t. There's no need for sub-second resolution.
(2) Use ktime_get_seconds() rather than ktime_get_real() so that time
isn't perceived to go backwards.
(3) Simplifying rxrpc_peer_keepalive_worker() by splitting it into two
parts:
(a) The "worker" function that manages the buckets and the timer.
(b) The "dispatch" function that takes the pending peers and
potentially transmits a keepalive packet before putting them back
in the ring into the slot appropriate to the revised last-Tx time.
(4) Taking everything that's pending out of the ring and splicing it into
a temporary collector list for processing.
In the case that there's been a significant jump forward, the ring
gets entirely emptied and then the time base can be warped forward
before the peers are processed.
The warping can't happen if the ring isn't empty because the slot a
peer is in is keepalive-time dependent, relative to the base time.
(5) Limit the number of iterations of the bucket array when scanning it.
(6) Set the timer to skip any empty slots as there's no point waking up if
there's nothing to do yet.
This can be triggered by an incoming call from a server after a reboot with
AF_RXRPC and AFS built into the kernel causing a peer record to be set up
before userspace is started. The system clock is then adjusted by
userspace, thereby potentially causing the keepalive generator to have a
meltdown - which leads to a message like:
Fixes: ace45bec6d77 ("rxrpc: Fix firewall route keepalive") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have been two reports that network doesn't come back on resume
from suspend when using MSI-X. Both cases affect the same chip version
(RTL8168g - version 40), on different systems. Falling back to MSI
fixes the issue.
Even though we don't really have a proof yet that the network chip
version is to blame, let's disable MSI-X for this version.
Reported-by: Steve Dodd <steved424@gmail.com> Reported-by: Lou Reed <gogen@disroot.org> Tested-by: Steve Dodd <steved424@gmail.com> Tested-by: Lou Reed <gogen@disroot.org> Fixes: 6c6aa15fdea5 ("r8169: improve interrupt handling") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
