The address space in CDSP PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB) which has a length of 0x10000. Value of 0x1400000 was
copied from older DTS, but it does not look accurate at all.
This should have no functional impact on Linux users, because PAS loader
does not use this address space at all.
The address space in ADSP PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB): 0x0680_0000 with length of 0x10000.
0x3000_0000, value used so far, is the main region of CDSP and was
simply copied from other/older DTS.
Correct the base address and length, which also moves the node to
different place to keep things sorted by unit address. The diff looks
big, but only the unit address and "reg" property were changed. This
should have no functional impact on Linux users, because PAS loader does
not use this address space at all.
The address space in MPSS/Modem PAS (Peripheral Authentication Service)
remoteproc node should point to the QDSP PUB address space
(QDSP6...SS_PUB) which has a length of 0x10000. Value of 0x4040 was
copied from older DTS, but it grew since then.
This should have no functional impact on Linux users, because PAS loader
does not use this address space at all.
Most SoC dtsi files have the display output interfaces disabled by
default, and only enabled on boards that utilize them. The MT8183
has it backwards: the display outputs are left enabled by default,
and only disabled at the board level.
Reverse the situation for the DPI output so that it follows the
normal scheme. For ease of backporting the DSI output is handled
in a separate patch.
Despite CM_IDLEST1_CORE and CM_FCLKEN1_CORE behaving normal,
disabling SPI leads to messages like when suspending:
Powerdomain (core_pwrdm) didn't enter target state 0
and according to /sys/kernel/debug/pm_debug/count off state is not
entered. That was not connected to SPI during the discussion
of disabling SPI. See:
https://lore.kernel.org/linux-omap/20230122100852.32ae082c@aktux/
The reason is that SPI is per default in slave mode. Linux driver
will turn it to master per default. It slave mode, the powerdomain seems to
be kept active if active chip select input is sensed.
Fix that by explicitly disabling the SPI3 pins which used to be muxed by
the bootloader since they are available on an optionally fitted header
which would require dtb overlays anyways.
Fixes: a622310f7f01 ("ARM: dts: gta04: fix excess dma channel usage") CC: stable@vger.kernel.org Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Reviewed-by: Roger Quadros <rogerq@kernel.org> Link: https://lore.kernel.org/r/20241204174152.2360431-1-andreas@kemnade.info Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bus_dma_limit was added for l3 bus by commit cfb5d65f2595
("ARM: dts: dra7: Add bus_dma_limit for L3 bus") to fix an issue
observed only with SATA on DRA7-EVM with 4GB RAM and CONFIG_ARM_LPAE
enabled.
Since kernel 5.13, the SATA issue can be reproduced again following
the SATA node move from L3 bus to L4_cfg in commit 8af15365a368
("ARM: dts: Configure interconnect target module for dra7 sata").
Fix it by adding an empty dma-ranges property to l4_cfg and
segment@100000 nodes (parent device tree node of SATA controller) to
inherit the 2GB dma ranges limit from l3 bus node.
Note: A similar fix was applied for PCIe controller by commit 90d4d3f4ea45 ("ARM: dts: dra7: Fix bus_dma_limit for PCIe").
GCC 15 changed the default C standard version to C23, which should not
have impacted the kernel because it requests the gnu11 standard via
'-std=' in the main Makefile. However, the x86 compressed boot Makefile
uses its own set of KBUILD_CFLAGS without a '-std=' value (i.e., using
the default), resulting in errors from the kernel's definitions of bool,
true, and false in stddef.h, which are reserved keywords under C23.
./include/linux/stddef.h:11:9: error: expected identifier before ‘false’
11 | false = 0,
./include/linux/types.h:35:33: error: two or more data types in declaration specifiers
35 | typedef _Bool bool;
Set '-std=gnu11' in the x86 compressed boot Makefile to resolve the
error and consistently use the same C standard version for the entire
kernel.
On some systems, the same CPU (with the same APIC ID) is assigned a
different logical CPU id after commit ec9aedb2aa1a ("x86/acpi: Ignore
invalid x2APIC entries").
This means that Linux enumerates the CPUs in a different order, which
violates ACPI specification[1] that states:
"OSPM should initialize processors in the order that they appear in
the MADT"
The problematic commit parses all LAPIC entries before any x2APIC
entries, aiming to ignore x2APIC entries with APIC ID < 255 when valid
LAPIC entries exist. However, it disrupts the CPU enumeration order on
systems where x2APIC entries precede LAPIC entries in the MADT.
Fix this problem by:
1) Parsing LAPIC entries first without registering them in the
topology to evaluate whether valid LAPIC entries exist.
2) Restoring the MADT in order parser which invokes either the LAPIC
or the X2APIC parser function depending on the entry type.
The X2APIC parser still ignores entries < 0xff in case that #1 found
valid LAPIC entries independent of their position in the MADT table.
When using Rust on the x86 architecture, we are currently using the
unstable target.json feature to specify the compilation target. Rustc is
going to change how softfloat is specified in the target.json file on
x86, thus update generate_rust_target.rs to specify softfloat using the
new option.
Note that if you enable this parameter with a compiler that does not
recognize it, then that triggers a warning but it does not break the
build.
[ For future reference, this solves the following error:
RUSTC L rust/core.o
error: Error loading target specification: target feature
`soft-float` is incompatible with the ABI but gets enabled in
target spec. Run `rustc --print target-list` for a list of
built-in targets
- Miguel ]
Cc: <stable@vger.kernel.org> # Needed in 6.12.y and 6.13.y only (Rust is pinned in older LTSs). Link: https://github.com/rust-lang/rust/pull/136146 Signed-off-by: Alice Ryhl <aliceryhl@google.com> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> # for x86 Link: https://lore.kernel.org/r/20250203-rustc-1-86-x86-softfloat-v1-1-220a72a5003e@google.com
[ Added 6.13.y too to Cc: stable tag and added reasoning to avoid
over-backporting. - Miguel ] Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-Wenum-enum-conversion was strengthened in clang-19 to warn for C, which
caused the kernel to move it to W=1 in commit 75b5ab134bb5 ("kbuild:
Move -Wenum-{compare-conditional,enum-conversion} into W=1") because
there were numerous instances that would break builds with -Werror.
Unfortunately, this is not a full solution, as more and more developers,
subsystems, and distributors are building with W=1 as well, so they
continue to see the numerous instances of this warning.
Since the move to W=1, there have not been many new instances that have
appeared through various build reports and the ones that have appeared
seem to be following similar existing patterns, suggesting that most
instances of this warning will not be real issues. The only alternatives
for silencing this warning are adding casts (which is generally seen as
an ugly practice) or refactoring the enums to macro defines or a unified
enum (which may be undesirable because of type safety in other parts of
the code).
Move the warning to W=2, where warnings that occur frequently but may be
relevant should reside.
Fail I/Os instead of retry to prevent user space processes from being
blocked on the I/O completion for several minutes.
Retrying I/Os during "depopulation in progress" or "depopulation restore in
progress" results in a continuous retry loop until the depopulation
completes or until the I/O retry loop is aborted due to a timeout by the
scsi_cmd_runtime_exceeced().
Depopulation is slow and can take 24+ hours to complete on 20+ TB HDDs.
Most I/Os in the depopulation retry loop end up taking several minutes
before returning the failure to user space.
Cc: stable@vger.kernel.org # 4.18.x: 2bbeb8d scsi: core: Handle depopulation and restoration in progress Cc: stable@vger.kernel.org # 4.18.x Fixes: e37c7d9a0341 ("scsi: core: sanitize++ in progress") Signed-off-by: Igor Pylypiv <ipylypiv@google.com> Link: https://lore.kernel.org/r/20250131184408.859579-1-ipylypiv@google.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In StorVSC, payload->range.len is used to indicate if this SCSI command
carries payload. This data is allocated as part of the private driver data
by the upper layer and may get passed to lower driver uninitialized.
For example, the SCSI error handling mid layer may send TEST_UNIT_READY or
REQUEST_SENSE while reusing the buffer from a failed command. The private
data section may have stale data from the previous command.
If the SCSI command doesn't carry payload, the driver may use this value as
is for communicating with host, resulting in possible corruption.
Fix this by always initializing this value.
Fixes: be0cf6ca301c ("scsi: storvsc: Set the tablesize based on the information given by the host") Cc: stable@kernel.org Tested-by: Roman Kisel <romank@linux.microsoft.com> Reviewed-by: Roman Kisel <romank@linux.microsoft.com> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Signed-off-by: Long Li <longli@microsoft.com> Link: https://lore.kernel.org/r/1737601642-7759-1-git-send-email-longli@linuxonhyperv.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_blk_crypto_profile_init() registers a cleanup handler to run when
the associated (platform-) device is being released. For UFS, the
crypto private data and pointers are stored as part of the ufs_hba's
data structure 'struct ufs_hba::crypto_profile'. This structure is
allocated as part of the underlying ufshcd and therefore Scsi_host
allocation.
During driver release or during error handling in ufshcd_pltfrm_init(),
this structure is released as part of ufshcd_dealloc_host() before the
(platform-) device associated with the crypto call above is released.
Once this device is released, the crypto cleanup code will run, using
the just-released 'struct ufs_hba::crypto_profile'. This causes a
use-after-free situation:
To fix this use-after free, change ufshcd_alloc_host() to register a
devres action to automatically cleanup the underlying SCSI device on
ufshcd destruction, without requiring explicit calls to
ufshcd_dealloc_host(). This way:
* the crypto profile and all other ufs_hba-owned resources are
destroyed before SCSI (as they've been registered after)
* a memleak is plugged in tc-dwc-g210-pci.c remove() as a
side-effect
* EXPORT_SYMBOL_GPL(ufshcd_dealloc_host) can be removed fully as
it's not needed anymore
* no future drivers using ufshcd_alloc_host() could ever forget
adding the cleanup
Fixes: cb77cb5abe1f ("blk-crypto: rename blk_keyslot_manager to blk_crypto_profile") Fixes: d76d9d7d1009 ("scsi: ufs: use devm_blk_ksm_init()") Cc: stable@vger.kernel.org Signed-off-by: André Draszik <andre.draszik@linaro.org> Link: https://lore.kernel.org/r/20250124-ufshcd-fix-v4-1-c5d0144aae59@linaro.org Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Acked-by: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 56541c7c4468 ("scsi: ufs: ufs-qcom: Switch to the new ICE API")
introduced an incorrect check of the algorithm ID into the key eviction
path, and thus qcom_ice_evict_key() is no longer ever called. Fix it.
Fixes: 56541c7c4468 ("scsi: ufs: ufs-qcom: Switch to the new ICE API") Cc: stable@vger.kernel.org Cc: Abel Vesa <abel.vesa@linaro.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Link: https://lore.kernel.org/r/20241210030839.1118805-1-ebiggers@kernel.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9604eea5bd3a ("scsi: st: Add third party poweron reset handling") in
v6.6 added new code to handle the Power On/Reset Unit Attention (POR UA)
sense data. This was in addition to the existing method. When this Unit
Attention is received, the driver blocks attempts to read, write and some
other operations because the reset may have rewinded the tape. Because of
the added code, also the initial POR UA resulted in blocking operations,
including those that are used to set the driver options after the device is
recognized. Also, reading and writing are refused, whereas they succeeded
before this commit.
Add code to not set pos_unknown to block operations if the POR UA is
received from the first test_ready() call after the st device has been
created. This restores the behavior before v6.6.
Signed-off-by: Kai Mäkisara <Kai.Makisara@kolumbus.fi> Link: https://lore.kernel.org/r/20241216113755.30415-1-Kai.Makisara@kolumbus.fi Fixes: 9604eea5bd3a ("scsi: st: Add third party poweron reset handling") CC: stable@vger.kernel.org Closes: https://lore.kernel.org/linux-scsi/2201CF73-4795-4D3B-9A79-6EE5215CF58D@kolumbus.fi/ Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When waking a VM's NX huge page recovery thread, ensure the thread is
actually alive before trying to wake it. Now that the thread is spawned
on-demand during KVM_RUN, a VM without a recovery thread is reachable via
the related module params.
In commit 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update
inbound map address") set_bar() was modified to support dynamically
changing the backing physical address of a BAR that was already configured.
This means that set_bar() can be called twice, without ever calling
clear_bar() (as calling clear_bar() would clear the BAR's PCI address
assigned by the host).
This can only be done if the new BAR size/flags does not differ from the
existing BAR configuration. Add these missing checks.
If we allow set_bar() to set e.g. a new BAR size that differs from the
existing BAR size, the new address translation range will be smaller than
the BAR size already determined by the host, which would mean that a read
past the new BAR size would pass the iATU untranslated, which could allow
the host to read memory not belonging to the new struct pci_epf_bar.
While at it, add comments which clarifies the support for dynamically
changing the physical address of a BAR. (Which was also missing.)
The "DesignWare Cores PCI Express Controller Register Descriptions,
Version 4.60a", section "1.21.70 IATU_LWR_TARGET_ADDR_OFF_INBOUND_i",
fields LWR_TARGET_RW and LWR_TARGET_HW both state that:
"Field size depends on log2(BAR_MASK+1) in BAR match mode."
I.e. only the upper bits are writable, and the number of writable bits is
dependent on the configured BAR_MASK.
If we do not write the BAR_MASK before writing the iATU registers, we are
relying the reset value of the BAR_MASK being larger than the requested
BAR size (which is supplied in the struct pci_epf_bar which is passed to
pci_epc_set_bar()). The reset value of the BAR_MASK is SoC dependent.
Thus, if the struct pci_epf_bar requests a BAR size that is larger than the
reset value of the BAR_MASK, the iATU will try to write to read-only bits,
which will cause the iATU to end up redirecting to a physical address that
is different from the address that was intended.
Thus, we should always write the iATU registers after writing the BAR_MASK.
When removing a virtual Endpoint, pci_epf_remove_vepf() failed to clear
epf_vf->epf_pf, which caused a subsequent pci_epf_add_vepf() to incorrectly
return -EBUSY:
Fix by clearing epf_vf->epf_pf in pci_epf_remove_vepf().
Link: https://lore.kernel.org/r/20241210-pci-epc-core_fix-v3-3-4d86dd573e4b@quicinc.com Fixes: 1cf362e907f3 ("PCI: endpoint: Add support to add virtual function in endpoint core") Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9d26d3a8f1b0 ("PCI: Put PCIe ports into D3 during suspend") sets the
policy that all PCIe ports are allowed to use D3. When the system is
suspended if the port is not power manageable by the platform and won't be
used for wakeup via a PME this sets up the policy for these ports to go
into D3hot.
This policy generally makes sense from an OSPM perspective but it leads to
problems with wakeup from suspend on the TUXEDO Sirius 16 Gen 1 with a
specific old BIOS. This manifests as a system hang.
On the affected Device + BIOS combination, add a quirk for the root port of
the problematic controller to ensure that these root ports are not put into
D3hot at suspend.
but with the added condition both in the documentation and in the code to
apply only to the TUXEDO Sirius 16 Gen 1 with a specific old BIOS and only
the affected root ports.
Fixes: 9d26d3a8f1b0 ("PCI: Put PCIe ports into D3 during suspend") Suggested-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20250114222436.1075456-1-wse@tuxedocomputers.com Co-developed-by: Georg Gottleuber <ggo@tuxedocomputers.com> Signed-off-by: Georg Gottleuber <ggo@tuxedocomputers.com> Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Cc: <stable@vger.kernel.org> # 6.1+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 25f39d3dcb48 ("s390/pci: Ignore RID for isolated VFs") PFs
which are not initially configured but in standby are considered
isolated. That is they create only a single function PCI domain. Due to
the PCI domains being created on discovery, this means that even if they
are configured later on, sibling PFs and their child VFs will not be
added to their PCI domain breaking SR-IOV expectations.
The reason the referenced commit ignored standby PFs for the creation of
multi-function PCI subhierarchies, was to work around a PCI domain
renumbering scenario on reboot. The renumbering would occur after
removing a previously in standby PF, whose domain number is used for its
configured sibling PFs and their child VFs, but which itself remained in
standby. When this is followed by a reboot, the sibling PF is used
instead to determine the PCI domain number of it and its child VFs.
In principle it is not possible to know which standby PFs will be
configured later and which may be removed. The PCI domain and root bus
are pre-requisites for hotplug slots so the decision of which functions
belong to which domain can not be postponed. With the renumbering
occurring only in rare circumstances and being generally benign, accept
it as an oddity and fix SR-IOV for initially standby PFs simply by
allowing them to create PCI domains.
For interrupt-map entries, the DTS specification requires
that #address-cells is defined for both the child node and the
interrupt parent. For the PCIe interrupt-map entries, the parent
node ("gic") has not specified #address-cells. The existing layout
of the PCIe interrupt-map entries indicates that it assumes
that #address-cells is zero for this node.
Explicitly set #address-cells to zero for "gic" so that it complies
with the device tree specification.
NVIDIA EDK2 works around this issue by assuming #address-cells
is zero in this scenario, but that workaround is being removed and so
this update is needed or else NVIDIA EDK2 cannot successfully parse the
device tree and the board cannot boot.
The auto_parser assumed sort() was stable, but the kernel's sort() uses
heapsort, which has never been stable. After commit 0e02ca29a563
("lib/sort: optimize heapsort with double-pop variation"), the order of
equal elements changed, causing the headset to fail to work.
Fix the issue by recording the original order of elements before
sorting and using it as a tiebreaker for equal elements in the
comparison function.
Fixes: b9030a005d58 ("ALSA: hda - Use standard sort function in hda_auto_parser.c") Reported-by: Austrum <austrum.lab@gmail.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219158 Tested-by: Austrum <austrum.lab@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com> Link: https://patch.msgid.link/20250128165415.643223-1-visitorckw@gmail.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent cleanup of the quirk table entries with the codec ID
matching caused a regression on some Lenovo Legion 7 models with PCI
SSID 17aa:386f: it assumed wrongly as if the codec SSID on the machine
were also 17aa:386f, but in this case, it was 17aa:38a8. This made
the binding with a wrong sub-codec, instead of TAS2781, the Cirrus
codec was bound.
For addressing the regression, correct the quirk entry to the right
value 17aa:38a8.
Note that this makes the entry appearing in an unsorted position.
This exception is needed because the entry must match before the PCI
SSID 17aa:386f.
Also there is another entry for 17aa:38a8, but the latter is for PCI
SSID matching while the new entry is for the codec SSID matching.
Positivo C6400 is equipped with ALC269VB, and it needs
ALC269VB_FIXUP_ASUS_ZENBOOK quirk to make its headset mic work.
Also must to limits the microphone boost.
Commit 2e4955167ec5 ("firmware: qcom: scm: Fix __scm and waitq
completion variable initialization") introduced a write barrier in probe
function to store global '__scm' variable. We all known barriers are
paired (see memory-barriers.txt: "Note that write barriers should
normally be paired with read or address-dependency barriers"), therefore
accessing it from concurrent contexts requires read barrier. Previous
commit added such barrier in qcom_scm_is_available(), so let's use that
directly.
Lack of this read barrier can result in fetching stale '__scm' variable
value, NULL, and dereferencing it.
Note that barrier in qcom_scm_is_available() satisfies here the control
dependency.
Fixes: ca61d6836e6f ("firmware: qcom: scm: fix a NULL-pointer dereference") Fixes: 449d0d84bcd8 ("firmware: qcom: scm: smc: switch to using the SCM allocator") Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20241209-qcom-scm-missing-barriers-and-all-sort-of-srap-v2-2-9061013c8d92@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2e4955167ec5 ("firmware: qcom: scm: Fix __scm and waitq
completion variable initialization") introduced a write barrier in probe
function to store global '__scm' variable. It also claimed that it
added a read barrier, because as we all known barriers are paired (see
memory-barriers.txt: "Note that write barriers should normally be paired
with read or address-dependency barriers"), however it did not really
add it.
The offending commit used READ_ONCE() to access '__scm' global which is
not a barrier.
The barrier is needed so the store to '__scm' will be properly visible.
This is most likely not fatal in current driver design, because missing
read barrier would mean qcom_scm_is_available() callers will access old
value, NULL. Driver does not support unbinding and does not correctly
handle probe failures, thus there is no risk of stale or old pointer in
'__scm' variable.
However for code correctness, readability and to be sure that we did not
mess up something in this tricky topic of SMP barriers, add a read
barrier for accessing '__scm'. Change also comment from useless/obvious
what does barrier do, to what is expected: which other parts of the code
are involved here.
Tomasz has reported that his device, Generalplus Technology Inc. 808 Camera,
with ID 1b3f:2002, stopped being detected:
$ ls -l /dev/video*
zsh: no matches found: /dev/video*
[ 7.230599] usb 3-2: Found multiple Units with ID 5
This particular device is non-compliant, having both the Output Terminal
and Processing Unit with ID 5. uvc_scan_fallback, though, is able to build
a chain. However, when media elements are added and uvc_mc_create_links
call uvc_entity_by_id, it will get the incorrect entity,
media_create_pad_link will WARN, and it will fail to register the entities.
In order to reinstate support for such devices in a timely fashion,
reverting the fix for these warnings is appropriate. A proper fix that
considers the existence of such non-compliant devices will be submitted in
a later development cycle.
Reported-by: Tomasz Sikora <sikora.tomus@gmail.com> Fixes: 3dd075fe8ebb ("media: uvcvideo: Require entities to have a non-zero unique ID") Cc: stable@vger.kernel.org Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Ricardo Ribalda <ribalda@chromium.org> Link: https://lore.kernel.org/r/20250114200045.1401644-1-cascardo@igalia.com Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
blkdev_read_iter() has a few odd checks, like gating the position and
count adjustment on whether or not the result is bigger-than-or-equal to
zero (where bigger than makes more sense), and not checking the return
value of blkdev_direct_IO() before doing an iov_iter_revert(). The
latter can lead to attempting to revert with a negative value, which
when passed to iov_iter_revert() as an unsigned value will lead to
throwing a WARN_ON() because unroll is bigger than MAX_RW_COUNT.
Be sane and don't revert for -EIOCBQUEUED, like what is done in other
spots.
2. More seriously, some workloads (for example, the test
stdlib/test-cxa_atexit2 in the Glibc test suite) triggers an RCU
stall and hang the system with a high probably (4 hangs out of 5
tests).
Revert this commit to use jiffie on Loongson MIPS systems and fix these
issues for now. The root cause may need more investigation.
Cc: stable@vger.kernel.org # 6.11+ Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Icenowy Zheng <icenowy@aosc.io> Signed-off-by: Xi Ruoyao <xry111@xry111.site> Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, installation of Debian 12.8 for mipsel fails on machines
without an FPU [1]. This is caused by the fact that zstd (which is used
for initramfs compression) executes the prefx instruction, which is not
emulated properly by the kernel.
The prefx (Prefetch Indexed) instruction fetches data from memory into
the cache without any side effects. Though functionally unrelated, it
requires an FPU [2].
Bytecode format of this instruction ends on "001111" binary:
case 0x3:
if (MIPSInst_FUNC(ir) != pfetch_op)
return SIGILL;
/* ignore prefx operation */
break;
default:
return SIGILL;
}
That snippet above contains a logic error and the
if (MIPSInst_FUNC(ir) != pfetch_op)
comparison always fires.
When MIPSInst_FUNC(ir) is equal to pfetch_op, ir must end on 001111
binary. In this case, MIPSInst_FMA_FFMT(ir) must be equal to 0x7, which
does not match that case label.
This causes emulation failure for the prefx instruction. Fix it.
This has been broken by
commit 919af8b96c89 ("MIPS: Make definitions of MIPSInst_FMA_{FUNC,FMTM} consistent with MIPS64 manual")
which modified the MIPSInst_FMA_FFMT macro without updating the users.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Cc: stable@vger.kernel.org # after 3 weeks Cc: Dengcheng Zhu <dzhu@wavecomp.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Ming Wang <wangming01@loongson.cn> Cc: Tiezhu Yang <yangtiezhu@loongson.cn> Fixes: 919af8b96c89 ("MIPS: Make definitions of MIPSInst_FMA_{FUNC,FMTM} consistent with MIPS64 manual") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[1] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=1091858
[2] MIPS Architecture For Programmers Volume II-A: The MIPS32 Instruction Set
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
dm-crypt uses tag_offset to index the integrity metadata for each crypt
sector. When the initial crypt_convert() returns BLK_STS_DEV_RESOURCE,
dm-crypt will try to continue the crypt/decrypt procedure in a kworker.
However, it resets tag_offset as zero instead of using the tag_offset
related with current sector. It may return unexpected data when using
random IV or return unexpected integrity related error.
Fix the problem by tracking tag_offset in per-IO convert_context.
Therefore, when the crypt/decrypt procedure continues in a kworker, it
could use the next tag_offset saved in convert_context.
Fixes: 8abec36d1274 ("dm crypt: do not wait for backlogged crypto request completion in softirq") Cc: stable@vger.kernel.org Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The updates of io->sector are the leftovers when dm-crypt allocated
pages for partial write request. However, since commit cf2f1abfbd0db
("dm crypt: don't allocate pages for a partial request"), there is no
partial request anymore.
After the introduction of write request rb-tree, the updates of
io->sectors may interfere the insertion procedure, because ->sectors of
these write requests which have already been added in the rb-tree may be
changed during the insertion of new write request.
Fix it by removing these buggy updates of io->sectors. Considering these
updates only effect the write request rb-tree, the commit which
introduces the write request rb-tree is used as the fix tag.
The PE Reset State "0" returned by RTAS calls
"ibm_read_slot_reset_[state|state2]" indicates that the reset is
deactivated and the PE is in a state where MMIO and DMA are allowed.
However, the current implementation of "pseries_eeh_get_state()" does
not reflect this, causing drivers to incorrectly assume that MMIO and
DMA operations cannot be resumed.
The userspace drivers as a part of EEH recovery using VFIO ioctls fail
to detect when the recovery process is complete. The VFIO_EEH_PE_GET_STATE
ioctl does not report the expected EEH_PE_STATE_NORMAL state, preventing
userspace drivers from functioning properly on pseries systems.
The patch addresses this issue by updating 'pseries_eeh_get_state()'
to include "EEH_STATE_MMIO_ENABLED" and "EEH_STATE_DMA_ENABLED" in
the result mask for PE Reset State "0". This ensures correct state
reporting to the callers, aligning the behavior with the PAPR specification
and fixing the bug in EEH recovery for VFIO user workflows.
The maximum number of load/store watchpoints and fetch instruction
watchpoints is 14 each according to LoongArch Reference Manual, so
extend the maximum number of watchpoints from 8 to 14 for ptrace.
By the way, just simply change 8 to 14 for the definition in struct
user_watch_state at the beginning, but it may corrupt uapi, then add
a new struct user_watch_state_v2 directly.
As far as I can tell, the only users for this struct in the userspace
are GDB and LLDB, there are no any problems of software compatibility
between the application and kernel according to the analysis.
The compatibility problem has been considered while developing and
testing. When the applications in the userspace get watchpoint state,
the length will be specified which is no bigger than the sizeof struct
user_watch_state or user_watch_state_v2, the actual length is assigned
as the minimal value of the application and kernel in the generic code
of ptrace:
For example, there are four kind of combinations, all of them work well.
(1) "older kernel + older gdb", the actual length is 8+(8+8+4+4)*8=200;
(2) "newer kernel + newer gdb", the actual length is 8+(8+8+4+4)*14=344;
(3) "older kernel + newer gdb", the actual length is 8+(8+8+4+4)*8=200;
(4) "newer kernel + older gdb", the actual length is 8+(8+8+4+4)*8=200.
Per Appendix A.7 in Q/LS 0013-2014 (龙芯CPU开发系统固件与内核接口规范 V2.2,
lit. Loongson DevSys Firmware Kernel Interface Specification V2.2),
interface_info.size is size of this interface, not size of the LEFI BIOS
ROM.
In any case, the BIOS ROM Size just cannot be several kilobytes (KB) on
Loongson64 LEFI platforms.
In the sh-sci driver, sci_ports[0] is used by earlycon. If the earlycon is
still active when sci_probe() is called and the new serial port is supposed
to map to sci_ports[0], return -EBUSY to prevent breaking the earlycon.
This situation should occurs in debug scenarios, and users should be
aware of the potential conflict.
The port_cfg object is used by serial_console_write(), which serves as
the write function for the earlycon device. Marking port_cfg as __initdata
causes it to be freed after kernel initialization, resulting in earlycon
becoming unavailable thereafter. Remove the __initdata macro from port_cfg
to resolve this issue.
The firmware used on MSM8916 exposes SOCINFO_VERSION(0, 8), which does not
have support for the serial_num field in the socinfo struct. There is an
existing check to avoid exposing the serial number in that case, but it's
not correct: When checking the item_size returned by SMEM, we need to make
sure the *end* of the serial_num is within bounds, instead of comparing
with the *start* offset. The serial_number currently exposed on MSM8916
devices is just an out of bounds read of whatever comes after the socinfo
struct in SMEM.
Fix this by changing offsetof() to offsetofend(), so that the size of the
field is also taken into account.
Back when the CRD support was brought up, the usb_2 controller didn't
have anything connected to it in order to test it properly, so it was
never enabled.
On the Lenovo ThinkPad T14s, the usb_2 controller has the fingerprint
controller connected to it. So enabling it, proved that the interrupts
lines were wrong from the start.
Fix both the pwr_event and the DWC ctrl_irq lines, according to
documentation.
Fixes: 4af46b7bd66f ("arm64: dts: qcom: x1e80100: Add USB nodes") Cc: stable@vger.kernel.org # 6.9 Signed-off-by: Abel Vesa <abel.vesa@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20250107-x1e80100-fix-usb2-controller-irqs-v1-1-4689aa9852a7@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the X1E80100 CRD, &vreg_l3e_1p2 only powers &usb_mp_qmpphy0/1
(i.e. USBSS_3 and USBSS_4). The QMP PHYs for USB_0, USB_1 and USB_2
are actually powered by &vreg_l2j_1p2.
Since x1e80100-microsoft-romulus mostly just mirrors the power supplies
from the x1e80100-crd device tree, assume that the fix also applies here.
Cc: stable@vger.kernel.org Fixes: 09d77be56093 ("arm64: dts: qcom: Add support for X1-based Surface Laptop 7 devices") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20241210-x1e80100-usb-qmp-supply-fix-v1-7-0adda5d30bbd@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the X1E80100 CRD, &vreg_l3e_1p2 only powers &usb_mp_qmpphy0/1
(i.e. USBSS_3 and USBSS_4). The QMP PHYs for USB_0, USB_1 and USB_2
are actually powered by &vreg_l2j_1p2.
Since x1e80100-lenovo-yoga-slim7x mostly just mirrors the power supplies
from the x1e80100-crd device tree, assume that the fix also applies here.
On the X1E80100 CRD, &vreg_l3e_1p2 only powers &usb_mp_qmpphy0/1
(i.e. USBSS_3 and USBSS_4). The QMP PHYs for USB_0, USB_1 and USB_2
are actually powered by &vreg_l2j_1p2.
Cc: stable@vger.kernel.org Fixes: ae5cee8e7349 ("arm64: dts: qcom: x1e80100-crd: Fix USB PHYs regulators") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20241210-x1e80100-usb-qmp-supply-fix-v1-4-0adda5d30bbd@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the X1E80100 CRD, &vreg_l3e_1p2 only powers &usb_mp_qmpphy0/1
(i.e. USBSS_3 and USBSS_4). The QMP PHYs for USB_0, USB_1 and USB_2
are actually powered by &vreg_l2j_1p2.
Since x1e78100-lenovo-thinkpad-t14s mostly just mirrors the power supplies
from the x1e80100-crd device tree, assume that the fix also applies here.
On the X1E80100 QCP, &vreg_l3e_1p2 only powers &usb_mp_qmpphy0/1
(i.e. USBSS_3 and USBSS_4). The QMP PHYs for USB_0, USB_1 and USB_2
are actually powered by &vreg_l2j_1p2.
Cc: stable@vger.kernel.org Fixes: 20676f7819d7 ("arm64: dts: qcom: x1e80100-qcp: Fix USB PHYs regulators") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20241210-x1e80100-usb-qmp-supply-fix-v1-8-0adda5d30bbd@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the X1E80100 CRD, &vreg_l3e_1p2 only powers &usb_mp_qmpphy0/1
(i.e. USBSS_3 and USBSS_4). The QMP PHYs for USB_0, USB_1 and USB_2
are actually powered by &vreg_l2j_1p2.
Since x1e80100-asus-vivobook-s15 mostly just mirrors the power supplies
from the x1e80100-crd device tree, assume that the fix also applies here.
Cc: stable@vger.kernel.org Fixes: d0e2f8f62dff ("arm64: dts: qcom: Add device tree for ASUS Vivobook S 15") Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org> Tested-by: Maud Spierings <maud_spierings@hotmail.com> Reviewed-by: Johan Hovold <johan+linaro@kernel.org> Link: https://lore.kernel.org/r/20241210-x1e80100-usb-qmp-supply-fix-v1-3-0adda5d30bbd@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clarify that the "NCM" implementation in `ipheth` is very limited, as
iOS devices aren't compatible with the CDC NCM specification in regular
tethering mode.
For a standards-compliant implementation, one shall turn to
the `cdc_ncm` module.
Cc: stable@vger.kernel.org # 6.5.x Signed-off-by: Foster Snowhill <forst@pen.gy> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Originally, the total NCM header size was computed as the sum of two
vaguely labelled constants. While accurate, it wasn't particularly clear
where they were coming from.
Use sizes of existing NCM structs where available. Define the total
NDP16 size based on the maximum amount of DPEs that can fit into the
iOS-specific fixed-size header.
This change does not fix any particular issue. Rather, it introduces
intermediate constants that will simplify subsequent commits.
It should also make it clearer for the reader where the constant values
come from.
Cc: stable@vger.kernel.org # 6.5.x Signed-off-by: Foster Snowhill <forst@pen.gy> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce an rx_error label to reduce repetitions in the header
signature checks.
Store wDatagramIndex and wDatagramLength after endianness conversion to
avoid repeated le16_to_cpu() calls.
Rewrite the loop to return on a null trailing DPE, which is required
by the CDC NCM spec. In case it is missing, fall through to rx_error.
This change does not fix any particular issue. Its purpose is to
simplify a subsequent commit that fixes a potential OoB read by limiting
the maximum amount of processed DPEs.
Cc: stable@vger.kernel.org # 6.5.x Signed-off-by: Foster Snowhill <forst@pen.gy> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By definition, a DPE points at the start of a network frame/datagram.
Thus it makes no sense for it to point at anything that's part of the
NCM header. It is not a security issue, but merely an indication of
a malformed DPE.
Enforce that all DPEs point at the data portion of the URB, past the
NCM header.
Original code allowed for the start of NDP16 to be anywhere within the
URB based on the `wNdpIndex` value in NTH16. Only the start position of
NDP16 was checked, so it was possible for even the fixed-length part
of NDP16 to extend past the end of URB, leading to an out-of-bounds
read.
On iOS devices, the NDP16 header always directly follows NTH16. Rely on
and check for this specific format.
This, along with NCM-specific minimal URB length check that already
exists, will ensure that the fixed-length part of NDP16 plus a set
amount of DPEs fit within the URB.
Note that this commit alone does not fully address the OoB read.
The limit on the amount of DPEs needs to be enforced separately.
The duplicate kmalloc here is causing memory leak. The request
preparation in bot_send_write_request is also done in
usbg_prepare_w_request. Remove the duplicate work.
We submitted the command with TARGET_SCF_ACK_KREF, which requires
acknowledgment of command completion. If the command fails, make sure to
decrement the ref count.
Fix 3 typos in 8703b driver. 2 typos in calibration routines are not
fatal and do not seem to have any impact, just fix them to match vendor
driver.
However the last one in rtw8703b_set_channel_bb() clears too many bits
in REG_OFDM0_TX_PSD_NOISE, causing TX and RX issues (neither rate goes
above MCS0-MCS1). Vendor driver clears only 2 most significant bits.
With the last typo fixed, the driver is able to reach MCS7 on Pinebook
Due to a limitation in available memory, the MT7916 firmware can only
handle either 5 GHz or 6 GHz at a time. It does not support runtime
switching without a full restart.
On older firmware, this accidentally worked to some degree due to missing
checks, but couldn't be supported properly, because it left the 6 GHz
channels uncalibrated.
Newer firmware refuses to start on either band if the passed EEPROM
data indicates support for both.
Deal with this limitation by using a module parameter to specify the
preferred band in case both are supported.
This is the equivalent of commit 28818b4d871b ("wifi: rtw88: usb: Fix
disconnection after beacon loss") for SDIO chips.
Tested on Pinephone (RTL8723CS), random disconnections became rare,
instead of a frequent nuisance.
Since brcmf_get_ip() can and actually will return NULL in this case the
call to brcmf_txfinalize() will result in a NULL pointer dereference inside
brcmf_txfinalize() when trying to update ifp->ndev->stats.tx_errors.
This will only happen if a flowring still has an skb.
Although the NULL pointer dereference has only been seen when trying to
update the tx statistic, all other uses of the ifp pointer have been
guarded as well with an early return if ifp is NULL.
RTL8821AE is stuck transmitting at the lowest rate allowed by the rate
mask. This is because the firmware doesn't know the device is connected
to a network.
Fix the macros SET_H2CCMD_MSRRPT_PARM_OPMODE and
SET_H2CCMD_MSRRPT_PARM_MACID_IND to work on the first byte of __cmd,
not the second. Now the firmware is correctly notified when the device
is connected to a network and it activates the rate control.
raw_spin_locks can be traced by lockdep or tracing itself. Atomic64
operations can be used in the tracing infrastructure. When an architecture
does not have true atomic64 operations it can use the generic version that
disables interrupts and uses spin_locks.
The tracing ring buffer code uses atomic64 operations for the time
keeping. But because some architectures use the default operations, the
locking inside the atomic operations can cause an infinite recursion.
As atomic64 implementation is architecture specific, it should not be
using raw_spin_locks() but instead arch_spin_locks as that is the purpose
of arch_spin_locks. To be used in architecture specific implementations of
generic infrastructure like atomic64 operations.
Note, by switching from raw_spin_locks to arch_spin_locks, the locks taken
to emulate the atomic64 operations will not have lockdep, mmio, or any
kind of checks done on them. They will not even disable preemption,
although the code will disable interrupts preventing the tasks that hold
the locks from being preempted. As the locks held are done so for very
short periods of time, and the logic is only done to emulate atomic64, not
having them be instrumented should not be an issue.
Cc: stable@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andreas Larsson <andreas@gaisler.com> Link: https://lore.kernel.org/20250122144311.64392baf@gandalf.local.home Fixes: c84897c0ff592 ("ring-buffer: Remove 32bit timestamp logic") Closes: https://lore.kernel.org/all/86fb4f86-a0e4-45a2-a2df-3154acc4f086@gaisler.com/ Reported-by: Ludwig Rydberg <ludwig.rydberg@gaisler.com> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some architectures can not safely do atomic64 operations in NMI context.
Since the ring buffer relies on atomic64 operations to do its time
keeping, if an event is requested in NMI context, reject it for these
architectures.
Cc: stable@vger.kernel.org Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Andreas Larsson <andreas@gaisler.com> Link: https://lore.kernel.org/20250120235721.407068250@goodmis.org Fixes: c84897c0ff592 ("ring-buffer: Remove 32bit timestamp logic") Closes: https://lore.kernel.org/all/86fb4f86-a0e4-45a2-a2df-3154acc4f086@gaisler.com/ Reported-by: Ludwig Rydberg <ludwig.rydberg@gaisler.com> Reviewed-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hid-sensor-hub creates the individual device structs and transfers them
to the created mfd platform-devices via the platform_data in the mfd_cell.
Before e651a1da442a ("HID: hid-sensor-hub: Allow parallel synchronous reads")
the sensor-hub was managing access centrally, with one "completion" in the
hub's data structure, which needed to be finished on removal at the latest.
The mentioned commit then moved this central management to each hid sensor
device, resulting on a completion in each struct hid_sensor_hub_device.
The remove procedure was adapted to go through all sensor devices and
finish any pending "completion".
What this didn't take into account was, platform_device_add_data() that is
used by mfd_add{_hotplug}_devices() does a kmemdup on the submitted
platform-data. So the data the platform-device gets is a copy of the
original data, meaning that the device worked on a different completion
than what sensor_hub_remove() currently wants to access.
To fix that, use device_for_each_child() to go through each child-device
similar to how mfd_remove_devices() unregisters the devices later and
with that get the live platform_data to finalize the correct completion.
Without remove hook to clear wake irq, there will be kernel dump when
doing module test.
"bbnsm_pwrkey 44440000.bbnsm:pwrkey: wake irq already initialized"
Add remove hook to clear wake irq and set wakeup to false.
"resource->end" needs to always be equal to "resource->start + size - 1".
The previous version of the function did not perform the "- 1" in case
of an empty resource.
Also make sure to allow an empty resource at address 0.
According to the UFS Device Specification, the dExtendedUFSFeaturesSupport
defines the support for TOO_HIGH_TEMPERATURE as bit[4] and the
TOO_LOW_TEMPERATURE as bit[5]. Correct the code to match with
the UFS device specification definition.
Cc: stable@vger.kernel.org Fixes: e88e2d32200a ("scsi: ufs: core: Probe for temperature notification support") Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com> Link: https://lore.kernel.org/r/69992b3e3e3434a5c7643be5a64de48be892ca46.1736793068.git.quic_nguyenb@quicinc.com Reviewed-by: Avri Altman <Avri.Altman@wdc.com> Reviewed-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison function cmpworker() violates the C standard's
requirements for qsort() comparison functions, which mandate symmetry
and transitivity:
Symmetry: If x < y, then y > x.
Transitivity: If x < y and y < z, then x < z.
In its current implementation, cmpworker() incorrectly returns 0 when
w1->tid < w2->tid, which breaks both symmetry and transitivity. This
violation causes undefined behavior, potentially leading to issues such
as memory corruption in glibc [1].
Fix the issue by returning -1 when w1->tid < w2->tid, ensuring
compliance with the C standard and preventing undefined behavior.
GCC 15 changed the default C standard version to C23, which should not
have impacted the kernel because it requests the gnu11 standard via
'-std=' in the main Makefile. However, the EFI libstub Makefile uses its
own set of KBUILD_CFLAGS for x86 without a '-std=' value (i.e., using
the default), resulting in errors from the kernel's definitions of bool,
true, and false in stddef.h, which are reserved keywords under C23.
./include/linux/stddef.h:11:9: error: expected identifier before ‘false’
11 | false = 0,
./include/linux/types.h:35:33: error: two or more data types in declaration specifiers
35 | typedef _Bool bool;
Set '-std=gnu11' in the x86 cflags to resolve the error and consistently
use the same C standard version for the entire kernel. All other
architectures reuse KBUILD_CFLAGS from the rest of the kernel, so this
issue is not visible for them.
blkcg_fill_root_iostats() iterates over @block_class's devices by
class_dev_iter_(init|next)(), but does not end iterating with
class_dev_iter_exit(), so causes the class's subsystem refcount leakage.
Fix by ending the iterating with class_dev_iter_exit().
Fixes: ef45fe470e1e ("blk-cgroup: show global disk stats in root cgroup io.stat") Reviewed-by: Michal Koutný <mkoutny@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com> Link: https://lore.kernel.org/r/20250105-class_fix-v6-2-3a2f1768d4d4@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When attaching uretprobes to processes running inside docker, the attached
process is segfaulted when encountering the retprobe.
The reason is that now that uretprobe is a system call the default seccomp
filters in docker block it as they only allow a specific set of known
syscalls. This is true for other userspace applications which use seccomp
to control their syscall surface.
Since uretprobe is a "kernel implementation detail" system call which is
not used by userspace application code directly, it is impractical and
there's very little point in forcing all userspace applications to
explicitly allow it in order to avoid crashing tracked processes.
Pass this systemcall through seccomp without depending on configuration.
Note: uretprobe is currently only x86_64 and isn't expected to ever be
supported in i386.
Some of the audio subsystem clocks defined in clk-mt2701.h aren't
actually used by the driver. This broke conversion to
mtk_clk_simple_probe which expects that the highest possible clk id is
defined by the ARRAY_SIZE.
Add additional dummy clocks to fill the gaps and remain compatible with
the existing DT bindings.
Fixes: 0f69a423c458 ("clk: mediatek: Switch to mtk_clk_simple_probe() where possible") Cc: stable@vger.kernel.org Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/a07584d803af57b9ce4b5df5e122c09bf5a56ac9.1734300668.git.daniel@makrotopia.org Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 973d1607d936 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to
simplify driver") broke DT bindings as the highest index was reduced by
1 because the id count starts from 1 and not from 0.
Fix this, like for other drivers which had the same issue, by adding a
dummy clk at index 0.
Fixes: 973d1607d936 ("clk: mediatek: mt2701: use mtk_clk_simple_probe to simplify driver") Cc: stable@vger.kernel.org Signed-off-by: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/r/b126a5577f3667ef19b1b5feea5e70174084fb03.1734300668.git.daniel@makrotopia.org Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
Add the parent_map property for the clock where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
If a clk_rcg2 has a parent, it should also have parent_map defined,
otherwise we'll get a NULL pointer dereference when calling clk_set_rate
like the following:
Add the parent_map property for two clocks where it's missing and also
un-inline the parent_data as well to keep the matching parent_map and
parent_data together.
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.8 Fixes: c58225b7e3d7 ("clk: qcom: add the SM8650 Global Clock Controller driver, part 1") Reported-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8650 Link: https://lore.kernel.org/r/20241219170011.70140-2-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With PWRSTS_OFF_ON, PCIe GDSCs are turned off during gdsc_disable(). This
can happen during scenarios such as system suspend and breaks the resume
of PCIe controllers from suspend.
So use PWRSTS_RET_ON to indicate the GDSC driver to not turn off the GDSCs
during gdsc_disable() and allow the hardware to transition the GDSCs to
retention when the parent domain enters low power state during system
suspend.
Cc: stable@vger.kernel.org # 6.2 Fixes: 955f2ea3b9e9 ("clk: qcom: Add GCC driver for SM8550") Reported-by: Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org> Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on QRD8550 Link: https://lore.kernel.org/r/20241219170011.70140-1-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson <andersson@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c45ae598fc16 ("clk: qcom: support for alpha mode configuration")
added support for configuring alpha mode, but it seems that the feature
was never working in practice.
The value of the alpha_{en,mode}_mask members of the configuration gets
added to the value parameter passed to the regmap_update_bits() function,
however the same values are not getting applied to the bitmask. As the
result, the respective bits in the USER_CTL register are never modifed
which leads to improper configuration of several PLLs.
The following table shows the PLL configurations where the 'alpha_en_mask'
member is set and which are passed as a parameter for the
clk_alpha_pll_configure() function. In the table the 'expected rate' column
shows the rate the PLL should run at with the given configuration, and
the 'real rate' column shows the rate the PLL runs at actually. The real
rates has been verified on hardwareOn IPQ* platforms, on other platforms,
those are computed values only.
As it can be seen from the above, there are several PLLs which are
configured incorrectly.
Change the code to apply both 'alpha_en_mask' and 'alpha_mode_mask'
values to the bitmask in order to configure the alpha mode correctly.
Applying the 'alpha_en_mask' fixes the initial rate of the PLLs showed
in the table above. Since the 'alpha_mode_mask' is not used by any driver
currently, that part of the change causes no functional changes.
Setting the genpd's struct device's name with dev_set_name() is
happening within pm_genpd_init(). If it remains NULL, things can blow up
later, such as when crafting the devfs hierarchy for the power domain:
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
...
Call trace:
strlen from start_creating+0x90/0x138
start_creating from debugfs_create_dir+0x20/0x178
debugfs_create_dir from genpd_debug_add.part.0+0x4c/0x144
genpd_debug_add.part.0 from genpd_debug_init+0x74/0x90
genpd_debug_init from do_one_initcall+0x5c/0x244
do_one_initcall from kernel_init_freeable+0x19c/0x1f4
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x28
Bisecting tracks this crash back to commit 899f44531fe6 ("pmdomain: core:
Add GENPD_FLAG_DEV_NAME_FW flag"), which exchanges use of genpd->name
with dev_name(&genpd->dev) in genpd_debug_add.part().
While testing the MMC nodes proposed in [1], it was noted that mmc0/1
would fail to initialize, with "mmc: fatal err update clk timeout" in
the kernel logs. A closer look at the clock definitions showed that the MMC
MPs had the "CLK_SET_RATE_NO_REPARENT" flag set. No reason was given for
adding this flag in the first place, and its original purpose is unknown,
but it doesn't seem to make sense and results in severe limitations to MMC
speeds. Thus, remove this flag from the 3 MMC MPs.
With vmalloc stack addresses enabled (CONFIG_VMAP_STACK=y) DCP trusted
keys can crash during en- and decryption of the blob encryption key via
the DCP crypto driver. This is caused by improperly using sg_init_one()
with vmalloc'd stack buffers (plain_key_blob).
Fix this by always using kmalloc() for buffers we give to the DCP crypto
driver.
Cc: stable@vger.kernel.org # v6.10+ Fixes: 0e28bf61a5f9 ("KEYS: trusted: dcp: fix leak of blob encryption key") Signed-off-by: David Gstir <david@sigma-star.at> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
