During noirq suspend phase the Raspberry Pi power driver suffer of
firmware property timeouts. The reason is that the IRQ of the underlying
BCM2835 mailbox is disabled and rpi_firmware_property_list() will always
run into a timeout [1].
Since the VideoCore side isn't consider as a wakeup source, set the
IRQF_NO_SUSPEND flag for the mailbox IRQ in order to keep it enabled
during suspend-resume cycle.
[1]
PM: late suspend of devices complete after 1.754 msecs
WARNING: CPU: 0 PID: 438 at drivers/firmware/raspberrypi.c:128
rpi_firmware_property_list+0x204/0x22c
Firmware transaction 0x00028001 timeout
Modules linked in:
CPU: 0 PID: 438 Comm: bash Tainted: G C 6.9.3-dirty #17
Hardware name: BCM2835
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x34/0x44
dump_stack_lvl from __warn+0x88/0xec
__warn from warn_slowpath_fmt+0x7c/0xb0
warn_slowpath_fmt from rpi_firmware_property_list+0x204/0x22c
rpi_firmware_property_list from rpi_firmware_property+0x68/0x8c
rpi_firmware_property from rpi_firmware_set_power+0x54/0xc0
rpi_firmware_set_power from _genpd_power_off+0xe4/0x148
_genpd_power_off from genpd_sync_power_off+0x7c/0x11c
genpd_sync_power_off from genpd_finish_suspend+0xcc/0xe0
genpd_finish_suspend from dpm_run_callback+0x78/0xd0
dpm_run_callback from device_suspend_noirq+0xc0/0x238
device_suspend_noirq from dpm_suspend_noirq+0xb0/0x168
dpm_suspend_noirq from suspend_devices_and_enter+0x1b8/0x5ac
suspend_devices_and_enter from pm_suspend+0x254/0x2e4
pm_suspend from state_store+0xa8/0xd4
state_store from kernfs_fop_write_iter+0x154/0x1a0
kernfs_fop_write_iter from vfs_write+0x12c/0x184
vfs_write from ksys_write+0x78/0xc0
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xcc93dfa8 to 0xcc93dff0)
[...]
PM: noirq suspend of devices complete after 3095.584 msecs
MODULE_DEVICE_TABLE(of, rockchip_mbox_of_match) could let the module
properly autoloaded based on the alias from of_device_id table. It
should be 'rockchip_mbox_of_match' instead of 'rockchp_mbox_of_match',
just fix it.
static_call_module_notify() triggers a WARN_ON(), when memory allocation
fails in __static_call_add_module().
That's not really justified, because the failure case must be correctly
handled by the well known call chain and the error code is passed
through to the initiating userspace application.
A memory allocation fail is not a fatal problem, but the WARN_ON() takes
the machine out when panic_on_warn is set.
Module insertion invokes static_call_add_module() to initialize the static
calls in a module. static_call_add_module() invokes __static_call_init(),
which allocates a struct static_call_mod to either encapsulate the built-in
static call sites of the associated key into it so further modules can be
added or to append the module to the module chain.
If that allocation fails the function returns with an error code and the
module core invokes static_call_del_module() to clean up eventually added
static_call_mod entries.
This works correctly, when all keys used by the module were converted over
to a module chain before the failure. If not then static_call_del_module()
causes a #GP as it blindly assumes that key::mods points to a valid struct
static_call_mod.
The problem is that key::mods is not a individual struct member of struct
static_call_key, it's part of a union to save space:
union {
/* bit 0: 0 = mods, 1 = sites */
unsigned long type;
struct static_call_mod *mods;
struct static_call_site *sites;
};
key::sites is a pointer to the list of built-in usage sites of the static
call. The type of the pointer is differentiated by bit 0. A mods pointer
has the bit clear, the sites pointer has the bit set.
As static_call_del_module() blidly assumes that the pointer is a valid
static_call_mod type, it fails to check for this failure case and
dereferences the pointer to the list of built-in call sites, which is
obviously bogus.
Cure it by checking whether the key has a sites or a mods pointer.
If it's a sites pointer then the key is not to be touched. As the sites are
walked in the same order as in __static_call_init() the site walk can be
terminated because all subsequent sites have not been touched by the init
code due to the error exit.
If it was converted before the allocation fail, then the inner loop which
searches for a module match will find nothing.
A fail in the second allocation in __static_call_init() is harmless and
does not require special treatment. The first allocation succeeded and
converted the key to a module chain. That first entry has mod::mod == NULL
and mod::next == NULL, so the inner loop of static_call_del_module() will
neither find a module match nor a module chain. The next site in the walk
was either already converted, but can't match the module, or it will exit
the outer loop because it has a static_call_site pointer and not a
static_call_mod pointer.
dev_err_probe() already prints the error code in a human readable way, so
there is no need to duplicate it as a numerical value at the end of the
message.
When the i2c bus recovery occurs, driver will send i2c stop command
in the scl low condition. In this case the sw state will still keep
original situation. Under multi-master usage, i2c bus recovery will
be called when i2c transfer timeout occurs. Update the stop command
calling with aspeed_i2c_do_stop function to update master_state.
The generic mmap_base code tries to leave a gap between the top of the
stack and the mmap base address, but enforces a minimum gap size (MIN_GAP)
of 128MB, which is too large on some setups. In particular, on arm tasks
without ADDR_LIMIT_32BIT, the STACK_TOP value is less than 128MB, so it's
impossible to fit such a gap in.
Only enforce this minimum if MIN_GAP < MAX_GAP, as we'd prefer to honour
MAX_GAP, which is defined proportionally, so scales better and always
leaves us with both _some_ stack space and some room for mmap.
This fixes the usercopy KUnit test suite on 32-bit arm, as it doesn't set
any personality flags so gets the default (in this case 26-bit) task size.
This test can be run with: ./tools/testing/kunit/kunit.py run --arch arm
usercopy --make_options LLVM=1
Link: https://lkml.kernel.org/r/20240803074642.1849623-2-davidgow@google.com Fixes: dba79c3df4a2 ("arm: use generic mmap top-down layout and brk randomization") Signed-off-by: David Gow <davidgow@google.com> Reviewed-by: Kees Cook <kees@kernel.org> Cc: Alexandre Ghiti <alex@ghiti.fr> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Russell King <linux@armlinux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
common_interrupt() and related variants call kvm_set_cpu_l1tf_flush_l1d(),
which is neither marked noinstr nor __always_inline.
So compiler puts it out of line and adds instrumentation to it. Since the
call is inside of instrumentation_begin/end(), objtool does not warn about
it.
The manifestation is that KCOV produces spurious coverage in
kvm_set_cpu_l1tf_flush_l1d() in random places because the call happens when
preempt count is not yet updated to say that the kernel is in an interrupt.
Mark kvm_set_cpu_l1tf_flush_l1d() as __always_inline and move it out of the
instrumentation_begin/end() section. It only calls __this_cpu_write()
which is already safe to call in noinstr contexts.
Fixes: 6368558c3710 ("x86/entry: Provide IDTENTRY_SYSVEC") Signed-off-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Alexander Potapenko <glider@google.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/3f9a1de9e415fcb53d07dc9e19fa8481bb021b1b.1718092070.git.dvyukov@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
FRED and IDT can share most of the definitions and declarations so
that in the majority of cases the actual handler implementation is the
same.
The differences are the exceptions where FRED stores exception related
information on the stack and the sysvec implementations as FRED can
handle irqentry/exit() in the dispatcher instead of having it in each
handler.
Also add stub defines for vectors which are not used due to Kconfig
decisions to spare the ifdeffery in the actual FRED dispatch code.
Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Xin Li <xin3.li@intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Tested-by: Shan Kang <shan.kang@intel.com> Link: https://lore.kernel.org/r/20231205105030.8698-23-xin3.li@intel.com
Stable-dep-of: 477d81a1c47a ("x86/entry: Remove unwanted instrumentation in common_interrupt()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Streams should flush their TRB cache, re-read TRBs, and start executing
TRBs from the beginning of the new dequeue pointer after a 'Set TR Dequeue
Pointer' command.
Cadence controllers may fail to start from the beginning of the dequeue
TRB as it doesn't clear the Opaque 'RsvdO' field of the stream context
during 'Set TR Dequeue' command. This stream context area is where xHC
stores information about the last partially executed TD when a stream
is stopped. xHC uses this information to resume the transfer where it left
mid TD, when the stream is restarted.
Patch fixes this by clearing out all RsvdO fields before initializing new
Stream transfer using a 'Set TR Dequeue Pointer' command.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: stable@vger.kernel.org Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/PH7PR07MB95386A40146E3EC64086F409DD9D2@PH7PR07MB9538.namprd07.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This quirk is for the controller that has a limitation in supporting
separate ERSTBA_HI and ERSTBA_LO programming. It's supported when
the ERSTBA is programmed ERSTBA_HI before ERSTBA_LO. That's because
the internal initialization of event ring fetches the
"Event Ring Segment Table Entry" based on the indication of ERSTBA_LO
written.
xhci_add_interrupter() erroneously preserves only the lowest 4 bits when
writing the ERSTBA register, not the lowest 6 bits. Fix it.
Migrate the ERST_BASE_RSVDP macro to the modern GENMASK_ULL() syntax to
avoid a u64 cast.
This was previously fixed by commit 8c1cbec9db1a ("xhci: fix event ring
segment table related masks and variables in header"), but immediately
undone by commit b17a57f89f69 ("xhci: Refactor interrupter code for
initial multi interrupter support.").
Fixes: b17a57f89f69 ("xhci: Refactor interrupter code for initial multi interrupter support.") Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v6.3+ Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20230915143108.1532163-5-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: e5fa8db0be3e ("usb: xhci: fix loss of data on Cadence xHC") Signed-off-by: Sasha Levin <sashal@kernel.org>
xHC supports several interrupters, each with its own mmio register set,
event ring and MSI/MSI-X vector. Transfers can be assigned different
interrupters when queued. See xhci 4.17 for details.
Current driver only supports one interrupter.
Create a xhci_interrupter structure containing an event ring, pointer to
mmio registers for this interrupter, variables to store registers over s3
suspend, erst, etc. Add functions to create and free an interrupter, and
pass an interrupter pointer to functions that deal with events.
Secondary interrupters are also useful without having an interrupt vector.
One use case is the xHCI audio sideband offloading where a DSP can take
care of specific audio endpoints.
When all transfer events of an offloaded endpoint can be mapped to a
separate interrupter event ring the DSP can poll this ring, and we can mask
these events preventing waking up the CPU.
Only minor functional changes such as clearing some of the interrupter
registers when freeing the interrupter.
xHC controller can supports up to 1024 interrupters.
To fit these change the max_interrupters varable from u8 to u16.
Add a separate mask for the reserve and preserve bits [5:0] in the erst
base register and use it instead of the ERST_PRT_MASK.
ERSR_PTR_MASK [3:0] is intended for masking bits in the
event ring dequeue pointer register.
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
Whilst we're at it, let's define some magic numbers to increase
readability and ease of maintenance.
When submitting more than 2^32 padata objects to padata_do_serial, the
current sorting implementation incorrectly sorts padata objects with
overflowed seq_nr, causing them to be placed before existing objects in
the reorder list. This leads to a deadlock in the serialization process
as padata_find_next cannot match padata->seq_nr and pd->processed
because the padata instance with overflowed seq_nr will be selected
next.
To fix this, we use an unsigned integer wrap around to correctly sort
padata objects in scenarios with integer overflow.
Fixes: bfde23ce200e ("padata: unbind parallel jobs from specific CPUs") Cc: <stable@vger.kernel.org> Co-developed-by: Christian Gafert <christian.gafert@rohde-schwarz.com> Signed-off-by: Christian Gafert <christian.gafert@rohde-schwarz.com> Co-developed-by: Max Ferger <max.ferger@rohde-schwarz.com> Signed-off-by: Max Ferger <max.ferger@rohde-schwarz.com> Signed-off-by: Van Giang Nguyen <vangiang.nguyen@rohde-schwarz.com> Acked-by: Daniel Jordan <daniel.m.jordan@oracle.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion of system address to physical memory address (as viewed by
the memory controller) by igen6_edac is incorrect when the system address
is above the TOM (Total amount Of populated physical Memory) for Elkhart
Lake and Ice Lake (Neural Network Processor). Fix this conversion.
Fixes: 10590a9d4f23 ("EDAC/igen6: Add EDAC driver for Intel client SoCs using IBECC") Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/stable/20240814061011.43545-1-qiuxu.zhuo%40intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c77e22834ae9 ("NFSv4: Fix a potential sleep while atomic in
nfs4_do_reclaim()") separate out the freeing of the state owners from
nfs4_purge_state_owners() and finish it outside the rcu lock.
However, the error path is omitted. As a result, the state owners in
"freeme" will not be released.
Fix it by adding freeing in the error path.
Fixes: c77e22834ae9 ("NFSv4: Fix a potential sleep while atomic in nfs4_do_reclaim()") Signed-off-by: Li Lingfeng <lilingfeng3@huawei.com> Cc: stable@vger.kernel.org # v5.3+ Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fcntl's F_SETOWN command sets the process that handle SIGIO/SIGURG
for the related file descriptor. Before this change, the
file_set_fowner LSM hook was always called, ignoring the VFS logic which
may not actually change the process that handles SIGIO (e.g. TUN, TTY,
dnotify), nor update the related UID/EUID.
Moreover, because security_file_set_fowner() was called without lock
(e.g. f_owner.lock), concurrent F_SETOWN commands could result to a race
condition and inconsistent LSM states (e.g. SELinux's fown_sid) compared
to struct fown_struct's UID/EUID.
This change makes sure the LSM states are always in sync with the VFS
state by moving the security_file_set_fowner() call close to the
UID/EUID updates and using the same f_owner.lock .
Rename f_modown() to __f_setown() to simplify code.
Cc: stable@vger.kernel.org Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Casey Schaufler <casey@schaufler-ca.com> Cc: Christian Brauner <brauner@kernel.org> Cc: James Morris <jmorris@namei.org> Cc: Jann Horn <jannh@google.com> Cc: Ondrej Mosnacek <omosnace@redhat.com> Cc: Paul Moore <paul@paul-moore.com> Cc: Serge E. Hallyn <serge@hallyn.com> Cc: Stephen Smalley <stephen.smalley.work@gmail.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Mickaël Salaün <mic@digikod.net> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently I noticed a bug[1] in btrfs, after digged it into
and I believe it'a race in vfs.
Let's assume there's a inode (ie ino 261) with i_count 1 is
called by iput(), and there's a concurrent thread calling
generic_shutdown_super().
cpu0: cpu1:
iput() // i_count is 1
->spin_lock(inode)
->dec i_count to 0
->iput_final() generic_shutdown_super()
->__inode_add_lru() ->evict_inodes()
// cause some reason[2] ->if (atomic_read(inode->i_count)) continue;
// return before // inode 261 passed the above check
// list_lru_add_obj() // and then schedule out
->spin_unlock()
// note here: the inode 261
// was still at sb list and hash list,
// and I_FREEING|I_WILL_FREE was not been set
btrfs_iget()
// after some function calls
->find_inode()
// found the above inode 261
->spin_lock(inode)
// check I_FREEING|I_WILL_FREE
// and passed
->__iget()
->spin_unlock(inode) // schedule back
->spin_lock(inode)
// check (I_NEW|I_FREEING|I_WILL_FREE) flags,
// passed and set I_FREEING
iput() ->spin_unlock(inode)
->spin_lock(inode) ->evict()
// dec i_count to 0
->iput_final()
->spin_unlock()
->evict()
Now, we have two threads simultaneously evicting
the same inode, which may trigger the BUG(inode->i_state & I_CLEAR)
statement both within clear_inode() and iput().
To fix the bug, recheck the inode->i_count after holding i_lock.
Because in the most scenarios, the first check is valid, and
the overhead of spin_lock() can be reduced.
If there is any misunderstanding, please let me know, thanks.
[1]: https://lore.kernel.org/linux-btrfs/000000000000eabe1d0619c48986@google.com/
[2]: The reason might be 1. SB_ACTIVE was removed or 2. mapping_shrinkable()
return false when I reproduced the bug.
Reported-by: syzbot+67ba3c42bcbb4665d3ad@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=67ba3c42bcbb4665d3ad CC: stable@vger.kernel.org Fixes: 63997e98a3be ("split invalidate_inodes()") Signed-off-by: Julian Sun <sunjunchao2870@gmail.com> Link: https://lore.kernel.org/r/20240823130730.658881-1-sunjunchao2870@gmail.com Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All batches of the Pine64 Pinebook Pro, except the latest batch (as of 2024)
whose hardware design was revised due to the component shortage, use a 1S
lithium battery whose nominal/design capacity is 10,000 mAh, according to the
battery datasheet. [1][2] Let's correct the design full-charge value in the
Pinebook Pro board dts, to improve the accuracy of the hardware description,
and to hopefully improve the accuracy of the fuel gauge a bit on all units
that don't belong to the latest batch.
The above-mentioned latest batch uses a different 1S lithium battery with
a slightly lower capacity, more precisely 9,600 mAh. To make the fuel gauge
work reliably on the latest batch, a sample battery would need to be sent to
CellWise, to obtain its proprietary battery profile, whose data goes into
"cellwise,battery-profile" in the Pinebook Pro board dts. Without that data,
the fuel gauge reportedly works unreliably, so changing the design capacity
won't have any negative effects on the already unreliable operation of the
fuel gauge in the Pinebook Pros that belong to the latest batch.
According to the battery datasheet, its voltage can go as low as 2.75 V while
discharging, but it's better to leave the current 3.0 V value in the dts file,
because of the associated Pinebook Pro's voltage regulation issues.
Increase the frequency of the PWM signal that drives the LED backlight of
the Pinebook Pro's panel, from about 1.35 KHz (which equals to the PWM
period of 740,740 ns), to exactly 8 kHz (which equals to the PWM period of
125,000 ns). Using a higher PWM frequency for the panel backlight, which
reduces the flicker, can only be beneficial to the end users' eyes.
On top of that, increasing the backlight PWM signal frequency reportedly
eliminates the buzzing emitted from the Pinebook Pro's built-in speakers
when certain backlight levels are set, which cause some weird interference
with some of the components of the Pinebook Pro's audio chain.
The old value for the backlight PWM period, i.e. 740,740 ns, is pretty much
an arbitrary value that was selected during the very early bring-up of the
Pinebook Pro, only because that value seemed to minimize horizontal line
distortion on the display, which resulted from the old X.org drivers causing
screen tearing when dragging windows around. That's no longer an issue, so
there are no reasons to stick with the old PWM period value.
The lower and the upper backlight PWM frequency limits for the Pinebook Pro's
panel, according to its datasheet, are 200 Hz and 10 kHz, respectively. [1]
These changes still leave some headroom, which may have some positive effects
on the lifetime expectancy of the panel's backlight LEDs.
The result of multiplication between values derived from functions
dir_buckets() and bucket_blocks() *could* technically reach
2^30 * 2^2 = 2^32.
While unlikely to happen, it is prudent to ensure that it will not
lead to integer overflow. Thus, use mul_u32_u32() as it's more
appropriate to mitigate the issue.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
fill_pool() uses 'obj_pool_min_free' to decide whether objects should be
handed back to the kmem cache. But 'obj_pool_min_free' records the lowest
historical value of the number of objects in the object pool and not the
minimum number of objects which should be kept in the pool.
Use 'debug_objects_pool_min_level' instead, which holds the minimum number
which was scaled to the number of CPUs at boot time.
[ tglx: Massage change log ]
Fixes: d26bf5056fc0 ("debugobjects: Reduce number of pool_lock acquisitions in fill_pool()") Fixes: 36c4ead6f6df ("debugobjects: Add global free list and the counter") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20240904133944.2124-3-thunder.leizhen@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"iw dev wlp2s0 station dump" shows incorrect rx bitrate:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 86.7 MBit/s VHT-MCS 9 VHT-NSS 1
This is because the RX band width is calculated incorrectly. Fix the
calculation according to the phydm_rxsc_2_bw() function from the
official drivers.
After:
tx bitrate: 866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
rx bitrate: 390.0 MBit/s VHT-MCS 9 80MHz VHT-NSS 1
It also works correctly with the AP configured for 20 MHz and 40 MHz.
pt_event_snapshot_aux() uses pt->handle_nmi to determine if tracing
needs to be stopped, however tracing can still be going because
pt->handle_nmi is set to zero before tracing is stopped in pt_event_stop,
whereas pt_event_snapshot_aux() requires that tracing must be stopped in
order to copy a sample of trace from the buffer.
Instead call pt_config_stop() always, which anyway checks config for
RTIT_CTL_TRACEEN and does nothing if it is already clear.
Note pt_event_snapshot_aux() can continue to use pt->handle_nmi to
determine if the trace needs to be restarted afterwards.
The TPM event log table is a Linux specific construct, where the data
produced by the GetEventLog() boot service is cached in memory, and
passed on to the OS using an EFI configuration table.
The use of EFI_LOADER_DATA here results in the region being left
unreserved in the E820 memory map constructed by the EFI stub, and this
is the memory description that is passed on to the incoming kernel by
kexec, which is therefore unaware that the region should be reserved.
Even though the utility of the TPM2 event log after a kexec is
questionable, any corruption might send the parsing code off into the
weeds and crash the kernel. So let's use EFI_ACPI_RECLAIM_MEMORY
instead, which is always treated as reserved by the E820 conversion
logic.
Internal documentation suggest that the TUXEDO Polaris 15 Gen5 AMD might
have GMxXGxX as the board name instead of GMxXGxx.
Adding both to be on the safe side.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Cc: All applicable <stable@vger.kernel.org> Link: https://patch.msgid.link/20240910094008.1601230-1-wse@tuxedocomputers.com Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only buffer objects are valid return values of _STR.
If something else is returned description_show() will access invalid
memory.
Fixes: d1efe3c324ea ("ACPI: Add new sysfs interface to export device description") Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Thomas Weißschuh <linux@weissschuh.net> Link: https://patch.msgid.link/20240709-acpi-sysfs-groups-v2-1-058ab0667fa8@weissschuh.net Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the net_conf pointer is NULL and the code attempts to access its
fields without a check, it will lead to a null pointer dereference.
Add a NULL check before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
The violation of atomicity occurs when the drbd_uuid_set_bm function is
executed simultaneously with modifying the value of
device->ldev->md.uuid[UI_BITMAP]. Consider a scenario where, while
device->ldev->md.uuid[UI_BITMAP] passes the validity check when its
value is not zero, the value of device->ldev->md.uuid[UI_BITMAP] is
written to zero. In this case, the check in drbd_uuid_set_bm might refer
to the old value of device->ldev->md.uuid[UI_BITMAP] (before locking),
which allows an invalid value to pass the validity check, resulting in
inconsistency.
To address this issue, it is recommended to include the data validity
check within the locked section of the function. This modification
ensures that the value of device->ldev->md.uuid[UI_BITMAP] does not
change during the validation process, thereby maintaining its integrity.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs to extract
function pairs that can be concurrently executed, and then analyzes the
instructions in the paired functions to identify possible concurrency
bugs including data races and atomicity violations.
Fixes: 9f2247bb9b75 ("drbd: Protect accesses to the uuid set with a spinlock") Cc: stable@vger.kernel.org Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com> Reviewed-by: Philipp Reisner <philipp.reisner@linbit.com> Link: https://lore.kernel.org/r/20240913083504.10549-1-chenqiuji666@gmail.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of sev PLATFORM_STATUS failure, sev_get_api_version() fails
resulting in sev_data field of psp_master nulled out. This later becomes
a problem when unloading the ccp module because the device has not been
unregistered (via misc_deregister()) before clearing the sev_data field
of psp_master. As a result, on reloading the ccp module, a duplicate
device issue is encountered as can be seen from the dmesg log below.
on reloading ccp module via modprobe ccp
Call Trace:
<TASK>
dump_stack_lvl+0xd7/0xf0
dump_stack+0x10/0x20
sysfs_warn_dup+0x5c/0x70
sysfs_create_dir_ns+0xbc/0xd
kobject_add_internal+0xb1/0x2f0
kobject_add+0x7a/0xe0
? srso_alias_return_thunk+0x5/0xfbef5
? get_device_parent+0xd4/0x1e0
? __pfx_klist_children_get+0x10/0x10
device_add+0x121/0x870
? srso_alias_return_thunk+0x5/0xfbef5
device_create_groups_vargs+0xdc/0x100
device_create_with_groups+0x3f/0x60
misc_register+0x13b/0x1c0
sev_dev_init+0x1d4/0x290 [ccp]
psp_dev_init+0x136/0x300 [ccp]
sp_init+0x6f/0x80 [ccp]
sp_pci_probe+0x2a6/0x310 [ccp]
? srso_alias_return_thunk+0x5/0xfbef5
local_pci_probe+0x4b/0xb0
work_for_cpu_fn+0x1a/0x30
process_one_work+0x203/0x600
worker_thread+0x19e/0x350
? __pfx_worker_thread+0x10/0x10
kthread+0xeb/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c/0x60
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
kobject: kobject_add_internal failed for sev with -EEXIST, don't try to register things with the same name in the same directory.
ccp 0000:22:00.1: sev initialization failed
ccp 0000:22:00.1: psp initialization failed
ccp 0000:a2:00.1: no command queues available
ccp 0000:a2:00.1: psp enabled
Address this issue by unregistering the /dev/sev before clearing out
sev_data in case of PLATFORM_STATUS failure.
PCI xHC host should be stopped and xhci driver memory freed before putting
host to PCI D3 state during PCI remove callback.
Hosts with XHCI_SPURIOUS_WAKEUP quirk did this the wrong way around
and set the host to D3 before calling usb_hcd_pci_remove(dev), which will
access the host to stop it, and then free xhci.
The write to RP2_GLOBAL_CMD followed by an immediate read of
RP2_GLOBAL_CMD in rp2_reset_asic() is intented to flush out the write,
however by then the device is already in reset and cannot respond to a
memory cycle access.
On platforms such as the Raspberry Pi 4 and others using the
pcie-brcmstb.c driver, any memory access to a device that cannot respond
is met with a fatal system error, rather than being substituted with all
1s as is usually the case on PC platforms.
Swapping the delay and the read ensures that the device has finished
resetting before we attempt to read from it.
Fixes: 7d9f49afa451 ("serial: rp2: New driver for Comtrol RocketPort 2 cards") Cc: stable <stable@kernel.org> Suggested-by: Jim Quinlan <james.quinlan@broadcom.com> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20240906225435.707837-1-florian.fainelli@broadcom.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most firmware names are hardcoded strings, or are constructed from fairly
constrained format strings where the dynamic parts are just some hex
numbers or such.
However, there are a couple codepaths in the kernel where firmware file
names contain string components that are passed through from a device or
semi-privileged userspace; the ones I could find (not counting interfaces
that require root privileges) are:
- lpfc_sli4_request_firmware_update() seems to construct the firmware
filename from "ModelName", a string that was previously parsed out of
some descriptor ("Vital Product Data") in lpfc_fill_vpd()
- nfp_net_fw_find() seems to construct a firmware filename from a model
name coming from nfp_hwinfo_lookup(pf->hwinfo, "nffw.partno"), which I
think parses some descriptor that was read from the device.
(But this case likely isn't exploitable because the format string looks
like "netronome/nic_%s", and there shouldn't be any *folders* starting
with "netronome/nic_". The previous case was different because there,
the "%s" is *at the start* of the format string.)
- module_flash_fw_schedule() is reachable from the
ETHTOOL_MSG_MODULE_FW_FLASH_ACT netlink command, which is marked as
GENL_UNS_ADMIN_PERM (meaning CAP_NET_ADMIN inside a user namespace is
enough to pass the privilege check), and takes a userspace-provided
firmware name.
(But I think to reach this case, you need to have CAP_NET_ADMIN over a
network namespace that a special kind of ethernet device is mapped into,
so I think this is not a viable attack path in practice.)
Fix it by rejecting any firmware names containing ".." path components.
For what it's worth, I went looking and haven't found any USB device
drivers that use the firmware loader dangerously.
Cc: stable@vger.kernel.org Reviewed-by: Danilo Krummrich <dakr@kernel.org> Fixes: abb139e75c2c ("firmware: teach the kernel to load firmware files directly from the filesystem") Signed-off-by: Jann Horn <jannh@google.com> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Link: https://lore.kernel.org/r/20240828-firmware-traversal-v3-1-c76529c63b5f@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dwc2_handle_usb_suspend_intr() function disables gadget clocks in USB
peripheral mode when no other power-down mode is available (introduced by
commit 0112b7ce68ea ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.")).
However, the dwc2_drd_role_sw_set() USB role update handler attempts to
read DWC2 registers if the USB role has changed while the USB is in suspend
mode (when the clocks are gated). This causes the system to hang.
Release the gadget clocks before handling the USB role update.
Fixes: 0112b7ce68ea ("usb: dwc2: Update dwc2_handle_usb_suspend_intr function.") Cc: stable@vger.kernel.org Signed-off-by: Tomas Marek <tomas.marek@elrest.cz> Link: https://lore.kernel.org/r/20240906055025.25057-1-tomas.marek@elrest.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix changes incorrect usb_request->status returned during disabling
endpoints. Before fix the status returned during dequeuing requests
while disabling endpoint was ECONNRESET.
Patch change it to ESHUTDOWN.
Patch fixes issue detected during testing UVC gadget.
During stopping streaming the class starts dequeuing usb requests and
controller driver returns the -ECONNRESET status. After completion
requests the class or application "uvc-gadget" try to queue this
request again. Changing this status to ESHUTDOWN cause that UVC assumes
that endpoint is disabled, or device is disconnected and stops
re-queuing usb requests.
TIOCGSERIAL is an ioctl. Thus it must be atomic. It returns
two values. Racing with set_serial it can return an inconsistent
result. The mutex must be taken.
In terms of logic the bug is as old as the driver. In terms of
code it goes back to the conversion to the get_serial and
set_serial methods.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Cc: stable <stable@kernel.org> Fixes: 99f75a1fcd865 ("cdc-acm: switch to ->[sg]et_serial()") Link: https://lore.kernel.org/r/20240912141916.1044393-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a small window during probing when IO is running
but the backlight is not registered. Processing events
during that time will crash. The completion handler
needs to check for a backlight before scheduling work.
The work can submit URBs and the URBs can schedule the work.
This cycle needs to be broken, when a device is to be stopped.
Use a flag to do so.
This is a design issue as old as the driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") CC: stable@vger.kernel.org Link: https://patch.msgid.link/20240919123525.688065-1-oneukum@suse.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SD cards can produce write latency spikes on the order of a hundred
milliseconds. If the target firmware does not hide that latency during DATA
IN and OUT phases it can cause the PDMA circuitry to raise a processor bus
fault which in turn leads to an unreliable byte count and a DMA overrun.
The Last Byte Sent flag is used to detect the overrun but this mechanism is
unreliable on some systems. Instead, set a DID_ERROR result whenever there
is a bus fault during a PDMA send, unless the cause was a phase mismatch.
Cc: stable@vger.kernel.org # 5.15+ Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Fixes: 7c1f3e3447a1 ("scsi: mac_scsi: Treat Last Byte Sent time-out as failure") Signed-off-by: Finn Thain <fthain@linux-m68k.org> Link: https://lore.kernel.org/r/cc38df687ace2c4ffc375a683b2502fc476b600d.1723001788.git.fthain@linux-m68k.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the error handling can be revised, some preparation is needed.
Refactor the polling loop with a new function, macscsi_wait_for_drq().
This function will gain more call sites in the next patch.
After a bus fault, capture and log the chip registers immediately, if the
NDEBUG_PSEUDO_DMA macro is defined. Remove some printk(KERN_DEBUG ...)
messages that aren't needed any more. Don't skip the debug message when
bytes == 0. Show all of the byte counters in the debug messages.
Currently amdgpu takes backlight caps provided by the ACPI tables
on systems as is. If the firmware sets maximums that are too low
this means that users don't get a good experience.
To avoid having to maintain a quirk list of such systems, do a sanity
check on the values. Check that the spread is at least half of the
values that amdgpu would use if no ACPI table was found and if not
use the amdgpu defaults.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3020 Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[WHY]
The calculated vtotal may has 1 line deviation. To get precisely
vtotal number, round the vtotal result.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Anthony Koo <anthony.koo@amd.com> Signed-off-by: Robin Chen <robin.chen@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Gen6 devices have the same problem and the same Solution as the Gen5
ones.
Some TongFang barebones have touchpad and/or keyboard issues after
suspend, fixable with nomux + reset + noloop + nopnp. Luckily, none of
them have an external PS/2 port so this can safely be set for all of
them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
Some TongFang barebones have touchpad and/or keyboard issues after
suspend, fixable with nomux + reset + noloop + nopnp. Luckily, none of
them have an external PS/2 port so this can safely be set for all of
them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use, no negative effects could be
observed when setting all four.
As Fedor Pchelkin pointed out, this commit violates the
convention of using the macro return value, which causes errors.
For example, in functions tda18271_attach(), xc5000_attach(),
simple_tuner_attach().
Link: https://lore.kernel.org/linux-media/20240424202031.syigrtrtipbq5f2l@fpc/ Suggested-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Roman Smirnov <r.smirnov@omp.ru> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return devm_of_clk_add_hw_provider() in order to transfer the error, if it
fails due to resource allocation failure or device tree clock provider
registration failure.
Cc: stable@vger.kernel.org Fixes: ebbfabc16d23 ("ASoC: rt5682: Add CCF usage for providing I2S clks") Signed-off-by: Ma Ke <make24@iscas.ac.cn> Link: https://patch.msgid.link/20240830143154.3448004-1-make24@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MSGF_LEG_MASK is laid out with INTA in bit 0, INTB in bit 1, INTC in bit 2,
and INTD in bit 3. Hardware IRQ numbers start at 0, and we register
PCI_NUM_INTX IRQs. So to enable INTA (aka hwirq 0) we should set bit 0.
Remove the subtraction of one.
This bug would cause INTx interrupts not to be delivered, as enabling INTB
would actually enable INTA, and enabling INTA wouldn't enable anything at
all. It is likely that this got overlooked for so long since most PCIe
hardware uses MSIs. This fixes the following UBSAN error:
UBSAN: shift-out-of-bounds in ../drivers/pci/controller/pcie-xilinx-nwl.c:389:11
shift exponent 18446744073709551615 is too large for 32-bit type 'int'
CPU: 1 PID: 61 Comm: kworker/u10:1 Not tainted 6.6.20+ #268
Hardware name: xlnx,zynqmp (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace (arch/arm64/kernel/stacktrace.c:235)
show_stack (arch/arm64/kernel/stacktrace.c:242)
dump_stack_lvl (lib/dump_stack.c:107)
dump_stack (lib/dump_stack.c:114)
__ubsan_handle_shift_out_of_bounds (lib/ubsan.c:218 lib/ubsan.c:387)
nwl_unmask_leg_irq (drivers/pci/controller/pcie-xilinx-nwl.c:389 (discriminator 1))
irq_enable (kernel/irq/internals.h:234 kernel/irq/chip.c:170 kernel/irq/chip.c:439 kernel/irq/chip.c:432 kernel/irq/chip.c:345)
__irq_startup (kernel/irq/internals.h:239 kernel/irq/chip.c:180 kernel/irq/chip.c:250)
irq_startup (kernel/irq/chip.c:270)
__setup_irq (kernel/irq/manage.c:1800)
request_threaded_irq (kernel/irq/manage.c:2206)
pcie_pme_probe (include/linux/interrupt.h:168 drivers/pci/pcie/pme.c:348)
Fixes: 9a181e1093af ("PCI: xilinx-nwl: Modify IRQ chip for legacy interrupts") Link: https://lore.kernel.org/r/20240531161337.864994-3-sean.anderson@linux.dev Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3f1b0e1f2875 (".gitignore update") added *.orig and *.rej
patterns to .gitignore in v2.6.23. The commit message didn't give a
rationale. Later on, commit 1f5d3a6b6532 ("Remove *.rej pattern from
.gitignore") removed the *.rej pattern in v2.6.26, on the rationale that
*.rej files indicated something went really wrong and should not be
ignored.
The *.rej files are now shown by `git status`, which helps located
conflicts when applying patches and lowers the probability that they
will go unnoticed. It is however still easy to overlook the *.orig files
which slowly polute the source tree. That's not as big of a deal as not
noticing a conflict, but it's still not nice.
Drop the *.orig pattern from .gitignore to avoid this and help keep the
source tree clean.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[masahiroy@kernel.org:
I do not have a strong opinion about this. Perhaps some people may have
a different opinion.
If you are someone who wants to ignore *.orig, it is likely you would
want to do so across all projects. Then, $XDG_CONFIG_HOME/git/ignore
would be more suitable for your needs. gitignore(5) suggests, "Patterns
which a user wants Git to ignore in all situations generally go into a
file specified by core.excludesFile in the user's ~/.gitconfig".
Please note that you cannot do the opposite; if *.orig is ignored by
the project's .gitignore, you cannot override the decision because
$XDG_CONFIG_HOME/git/ignore has a lower priority.
If *.orig is sitting on the fence, I'd leave it to the users. ] Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Gresko reports that the root user on an NFS client is able to
change the security labels on files on an NFS filesystem that is
exported with root squashing enabled.
The end of the kerneldoc comment for __vfs_setxattr_noperm() states:
* This function requires the caller to lock the inode's i_mutex before it
* is executed. It also assumes that the caller will make the appropriate
* permission checks.
nfsd_setattr() does do permissions checking via fh_verify() and
nfsd_permission(), but those don't do all the same permissions checks
that are done by security_inode_setxattr() and its related LSM hooks do.
Since nfsd_setattr() is the only consumer of security_inode_setsecctx(),
simplest solution appears to be to replace the call to
__vfs_setxattr_noperm() with a call to __vfs_setxattr_locked(). This
fixes the above issue and has the added benefit of causing nfsd to
recall conflicting delegations on a file when a client tries to change
its security label.
Cc: stable@kernel.org Reported-by: Marek Gresko <marek.gresko@protonmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=218809 Signed-off-by: Scott Mayhew <smayhew@redhat.com> Tested-by: Stephen Smalley <stephen.smalley.work@gmail.com> Reviewed-by: Stephen Smalley <stephen.smalley.work@gmail.com> Reviewed-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Acked-by: Casey Schaufler <casey@schaufler-ca.com> Signed-off-by: Paul Moore <paul@paul-moore.com>
[Shivani: Modified to apply on v5.15.y-v6.1.y] Signed-off-by: Shivani Agarwal <shivani.agarwal@broadcom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New CPU #defines encode vendor and family as well as model.
[ dhansen: vertically align 0's in invlpg_miss_ids[] ]
Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Link: https://lore.kernel.org/all/20240424181518.41946-1-tony.luck%40intel.com
[ Ricardo: I used the old match macro X86_MATCH_INTEL_FAM6_MODEL()
instead of X86_MATCH_VFM() as in the upstream commit.
I also kept the ALDERLAKE_N name instead of ATOM_GRACEMONT. Both refer
to the same CPU model. ] Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current initialization of the struct x86_cpu_id via
pl4_support_ids[] is partial and wrong. It is initializing
"stepping" field with "X86_FEATURE_ANY" instead of "feature" field.
Use X86_MATCH_INTEL_FAM6_MODEL macro instead of initializing
each field of the struct x86_cpu_id for pl4_supported list of CPUs.
This X86_MATCH_INTEL_FAM6_MODEL macro internally uses another macro
X86_MATCH_VENDOR_FAM_MODEL_FEATURE for X86 based CPU matching with
appropriate initialized values.
Reported-by: Dave Hansen <dave.hansen@intel.com> Link: https://lore.kernel.org/lkml/28ead36b-2d9e-1a36-6f4e-04684e420260@intel.com Fixes: eb52bc2ae5b8 ("powercap: RAPL: Add Power Limit4 support for Meteor Lake SoC") Fixes: b08b95cf30f5 ("powercap: RAPL: Add Power Limit4 support for Alder Lake-N and Raptor Lake-P") Fixes: 515755906921 ("powercap: RAPL: Add Power Limit4 support for RaptorLake") Fixes: 1cc5b9a411e4 ("powercap: Add Power Limit4 support for Alder Lake SoC") Fixes: 8365a898fe53 ("powercap: Add Power Limit4 support") Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[ Ricardo: I only kept TIGERLAKE, ALDERLAKE, and ALDERLAKE_L in
pl4_support_ids as only these models are enumerated before this
changeset. ] Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only provide ctnetlink_label_size when it is used,
which is when CONFIG_NF_CONNTRACK_EVENTS is configured.
Flagged by clang-18 W=1 builds as:
.../nf_conntrack_netlink.c:385:19: warning: unused function 'ctnetlink_label_size' [-Wunused-function]
385 | static inline int ctnetlink_label_size(const struct nf_conn *ct)
| ^~~~~~~~~~~~~~~~~~~~
The condition on CONFIG_NF_CONNTRACK_LABELS being removed by
this patch guards compilation of non-trivial implementations
of ctnetlink_dump_labels() and ctnetlink_label_size().
However, this is not necessary as each of these functions
will always return 0 if CONFIG_NF_CONNTRACK_LABELS is not defined
as each function starts with the equivalent of:
And nf_ct_labels_find always returns NULL if CONFIG_NF_CONNTRACK_LABELS
is not enabled. So I believe that the compiler optimises the code away
in such cases anyway.
Found by inspection.
Compile tested only.
Originally splitted in two patches, Pablo Neira Ayuso collapsed them and
added Fixes: tag.
Fixes: 0ceabd83875b ("netfilter: ctnetlink: deliver labels to userspace") Link: https://lore.kernel.org/netfilter-devel/20240909151712.GZ2097826@kernel.org/ Signed-off-by: Simon Horman <horms@kernel.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Documentation of list_del_rcu() warns callers to not immediately free
the deleted list item. While it seems not necessary to use the
RCU-variant of list_del() here in the first place, doing so seems to
require calling kfree_rcu() on the deleted item as well.
Fixes: 3f0465a9ef02 ("netfilter: nf_tables: dynamically allocate hooks per net_device in flowtables") Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a WARNING in bond_xdp_get_xmit_slave. To reproduce
this[1], one bond device (bond1) has xdpdrv, which increases
bpf_master_redirect_enabled_key. Another bond device (bond0) which is
unsupported by XDP but its slave (veth3) has xdpgeneric that returns
XDP_TX. This triggers WARN_ON_ONCE() from the xdp_master_redirect().
To reduce unnecessary warnings and improve log management, we need to
delete the WARN_ON_ONCE() and add ratelimit to the netdev_err().
[1] Steps to reproduce:
# Needs tx_xdp with return XDP_TX;
ip l add veth0 type veth peer veth1
ip l add veth3 type veth peer veth4
ip l add bond0 type bond mode 6 # BOND_MODE_ALB, unsupported by XDP
ip l add bond1 type bond # BOND_MODE_ROUNDROBIN by default
ip l set veth0 master bond1
ip l set bond1 up
# Increases bpf_master_redirect_enabled_key
ip l set dev bond1 xdpdrv object tx_xdp.o section xdp_tx
ip l set veth3 master bond0
ip l set bond0 up
ip l set veth4 up
# Triggers WARN_ON_ONCE() from the xdp_master_redirect()
ip l set veth3 xdpgeneric object tx_xdp.o section xdp_tx
Reported-by: syzbot+c187823a52ed505b2257@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=c187823a52ed505b2257 Fixes: 9e2ee5c7e7c3 ("net, bonding: Add XDP support to the bonding driver") Signed-off-by: Jiwon Kim <jiwonaid0@gmail.com> Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20240918140602.18644-1-jiwonaid0@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When broadcasting data to multiple nodes via MHI, using skb_clone()
causes all nodes to receive the same header data. This can result in
packets being discarded by endpoints, leading to lost data.
This issue occurs when a socket is closed, and a QRTR_TYPE_DEL_CLIENT
packet is broadcasted. All nodes receive the same destination node ID,
causing the node connected to the client to discard the packet and
remain unaware of the client's deletion.
Replace skb_clone() with pskb_copy(), to create a separate copy of
the header for each sk_buff.
Fixes: bdabad3e363d ("net: Add Qualcomm IPC router") Signed-off-by: Youssef Samir <quic_yabdulra@quicinc.com> Reviewed-by: Jeffery Hugo <quic_jhugo@quicinc.com> Reviewed-by: Carl Vanderlip <quic_carlv@quicinc.com> Reviewed-by: Chris Lew <quic_clew@quicinc.com> Link: https://patch.msgid.link/20240916170858.2382247-1-quic_yabdulra@quicinc.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We have some machines running stock Ubuntu 20.04.6 which is their 5.4.0-174-generic
kernel that are running ceph and recently hit a null ptr dereference in
tcp_rearm_rto(). Initially hitting it from the TLP path, but then later we also
saw it getting hit from the RACK case as well. Here are examples of the oops
messages we saw in each of those cases:
After we hit this we disabled TLP by setting tcp_early_retrans to 0 and then hit the crash in the RACK case:
Aug 7 07:26:16 rx [1006006.265582] BUG: kernel NULL pointer dereference, address: 0000000000000020
Aug 7 07:26:16 rx [1006006.272719] #PF: supervisor read access in kernel mode
Aug 7 07:26:16 rx [1006006.278030] #PF: error_code(0x0000) - not-present page
Aug 7 07:26:16 rx [1006006.283343] PGD 0 P4D 0
Aug 7 07:26:16 rx [1006006.286057] Oops: 0000 [#1] SMP NOPTI
Aug 7 07:26:16 rx [1006006.289896] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G W 5.4.0-174-generic #193-Ubuntu
Aug 7 07:26:16 rx [1006006.299107] Hardware name: Supermicro SMC 2x26 os-gen8 64C NVME-Y 256G/H12SSW-NTR, BIOS 2.5.V1.2U.NVMe.UEFI 05/09/2023
Aug 7 07:26:16 rx [1006006.309970] RIP: 0010:tcp_rearm_rto+0xe4/0x160
Aug 7 07:26:16 rx [1006006.314584] Code: 87 ca 04 00 00 00 5b 41 5c 41 5d 5d c3 c3 49 8b bc 24 40 06 00 00 eb 8d 48 bb cf f7 53 e3 a5 9b c4 20 4c 89 ef e8 0c fe 0e 00 <48> 8b 78 20 48 c1 ef 03 48 89 f8 41 8b bc 24 80 04 00 00 48 f7 e3
Aug 7 07:26:16 rx [1006006.333499] RSP: 0018:ffffb42600a50960 EFLAGS: 00010246
Aug 7 07:26:16 rx [1006006.338895] RAX: 0000000000000000 RBX: 20c49ba5e353f7cf RCX: 0000000000000000
Aug 7 07:26:16 rx [1006006.346193] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffff92d687ed8160
Aug 7 07:26:16 rx [1006006.353489] RBP: ffffb42600a50978 R08: 0000000000000000 R09: 00000000cd896dcc
Aug 7 07:26:16 rx [1006006.360786] R10: ffff92dc3404f400 R11: 0000000000000001 R12: ffff92d687ed8000
Aug 7 07:26:16 rx [1006006.368084] R13: ffff92d687ed8160 R14: 00000000cd896dcc R15: 00000000cd8fca81
Aug 7 07:26:16 rx [1006006.375381] FS: 0000000000000000(0000) GS:ffff93158ad40000(0000) knlGS:0000000000000000
Aug 7 07:26:16 rx [1006006.383632] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Aug 7 07:26:16 rx [1006006.389544] CR2: 0000000000000020 CR3: 0000003e775ce006 CR4: 0000000000760ee0
Aug 7 07:26:16 rx [1006006.396839] PKRU: 55555554
Aug 7 07:26:16 rx [1006006.399717] Call Trace:
Aug 7 07:26:16 rx [1006006.402335]
Aug 7 07:26:16 rx [1006006.404525] ? show_regs.cold+0x1a/0x1f
Aug 7 07:26:16 rx [1006006.408532] ? __die+0x90/0xd9
Aug 7 07:26:16 rx [1006006.411760] ? no_context+0x196/0x380
Aug 7 07:26:16 rx [1006006.415599] ? __bad_area_nosemaphore+0x50/0x1a0
Aug 7 07:26:16 rx [1006006.420392] ? _raw_spin_lock+0x1e/0x30
Aug 7 07:26:16 rx [1006006.424401] ? bad_area_nosemaphore+0x16/0x20
Aug 7 07:26:16 rx [1006006.428927] ? do_user_addr_fault+0x267/0x450
Aug 7 07:26:16 rx [1006006.433450] ? __do_page_fault+0x58/0x90
Aug 7 07:26:16 rx [1006006.437542] ? do_page_fault+0x2c/0xe0
Aug 7 07:26:16 rx [1006006.441470] ? page_fault+0x34/0x40
Aug 7 07:26:16 rx [1006006.445134] ? tcp_rearm_rto+0xe4/0x160
Aug 7 07:26:16 rx [1006006.449145] tcp_ack+0xa32/0xb30
Aug 7 07:26:16 rx [1006006.452542] tcp_rcv_established+0x13c/0x670
Aug 7 07:26:16 rx [1006006.456981] ? sk_filter_trim_cap+0x48/0x220
Aug 7 07:26:16 rx [1006006.461419] tcp_v6_do_rcv+0xdb/0x450
Aug 7 07:26:16 rx [1006006.465257] tcp_v6_rcv+0xc2b/0xd10
Aug 7 07:26:16 rx [1006006.468918] ip6_protocol_deliver_rcu+0xd3/0x4e0
Aug 7 07:26:16 rx [1006006.473706] ip6_input_finish+0x15/0x20
Aug 7 07:26:16 rx [1006006.477710] ip6_input+0xa2/0xb0
Aug 7 07:26:16 rx [1006006.481109] ? ip6_protocol_deliver_rcu+0x4e0/0x4e0
Aug 7 07:26:16 rx [1006006.486151] ip6_sublist_rcv_finish+0x3d/0x50
Aug 7 07:26:16 rx [1006006.490679] ip6_sublist_rcv+0x1aa/0x250
Aug 7 07:26:16 rx [1006006.494779] ? ip6_rcv_finish_core.isra.0+0xa0/0xa0
Aug 7 07:26:16 rx [1006006.499828] ipv6_list_rcv+0x112/0x140
Aug 7 07:26:16 rx [1006006.503748] __netif_receive_skb_list_core+0x1a4/0x250
Aug 7 07:26:16 rx [1006006.509057] netif_receive_skb_list_internal+0x1a1/0x2b0
Aug 7 07:26:16 rx [1006006.514538] gro_normal_list.part.0+0x1e/0x40
Aug 7 07:26:16 rx [1006006.519068] napi_complete_done+0x91/0x130
Aug 7 07:26:16 rx [1006006.523352] mlx5e_napi_poll+0x18e/0x610 [mlx5_core]
Aug 7 07:26:16 rx [1006006.528481] net_rx_action+0x142/0x390
Aug 7 07:26:16 rx [1006006.532398] __do_softirq+0xd1/0x2c1
Aug 7 07:26:16 rx [1006006.536142] irq_exit+0xae/0xb0
Aug 7 07:26:16 rx [1006006.539452] do_IRQ+0x5a/0xf0
Aug 7 07:26:16 rx [1006006.542590] common_interrupt+0xf/0xf
Aug 7 07:26:16 rx [1006006.546421]
Aug 7 07:26:16 rx [1006006.548695] RIP: 0010:native_safe_halt+0xe/0x10
Aug 7 07:26:16 rx [1006006.553399] Code: 7b ff ff ff eb bd 90 90 90 90 90 90 e9 07 00 00 00 0f 00 2d 36 2c 50 00 f4 c3 66 90 e9 07 00 00 00 0f 00 2d 26 2c 50 00 fb f4 90 0f 1f 44 00 00 55 48 89 e5 41 55 41 54 53 e8 dd 5e 61 ff 65
Aug 7 07:26:16 rx [1006006.572309] RSP: 0018:ffffb42600177e70 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffc2
Aug 7 07:26:16 rx [1006006.580040] RAX: ffffffff8ed08b20 RBX: 0000000000000005 RCX: 0000000000000001
Aug 7 07:26:16 rx [1006006.587337] RDX: 00000000f48eeca2 RSI: 0000000000000082 RDI: 0000000000000082
Aug 7 07:26:16 rx [1006006.594635] RBP: ffffb42600177e90 R08: 0000000000000000 R09: 000000000000020f
Aug 7 07:26:16 rx [1006006.601931] R10: 0000000000100000 R11: 0000000000000000 R12: 0000000000000005
Aug 7 07:26:16 rx [1006006.609229] R13: ffff93157deb5f00 R14: 0000000000000000 R15: 0000000000000000
Aug 7 07:26:16 rx [1006006.616530] ? __cpuidle_text_start+0x8/0x8
Aug 7 07:26:16 rx [1006006.620886] ? default_idle+0x20/0x140
Aug 7 07:26:16 rx [1006006.624804] arch_cpu_idle+0x15/0x20
Aug 7 07:26:16 rx [1006006.628545] default_idle_call+0x23/0x30
Aug 7 07:26:16 rx [1006006.632640] do_idle+0x1fb/0x270
Aug 7 07:26:16 rx [1006006.636035] cpu_startup_entry+0x20/0x30
Aug 7 07:26:16 rx [1006006.640126] start_secondary+0x178/0x1d0
Aug 7 07:26:16 rx [1006006.644218] secondary_startup_64+0xa4/0xb0
Aug 7 07:26:17 rx [1006006.648568] Modules linked in: vrf bridge stp llc vxlan ip6_udp_tunnel udp_tunnel nls_iso8859_1 nft_ct amd64_edac_mod edac_mce_amd kvm_amd kvm crct10dif_pclmul ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper wmi_bmof ipmi_ssif input_leds joydev rndis_host cdc_ether usbnet ast mii drm_vram_helper ttm drm_kms_helper i2c_algo_bit fb_sys_fops syscopyarea sysfillrect sysimgblt ccp mac_hid ipmi_si ipmi_devintf ipmi_msghandler sch_fq_codel nf_tables_set nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables nfnetlink ramoops reed_solomon efi_pstore drm ip_tables x_tables autofs4 raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid0 multipath linear mlx5_ib ib_uverbs ib_core raid1 hid_generic mlx5_core pci_hyperv_intf crc32_pclmul usbhid ahci tls mlxfw bnxt_en hid libahci nvme i2c_piix4 nvme_core wmi [last unloaded: cpuid]
Aug 7 07:26:17 rx [1006006.726180] CR2: 0000000000000020
Aug 7 07:26:17 rx [1006006.729718] ---[ end trace e0e2e37e4e612984 ]---
Prior to seeing the first crash and on other machines we also see the warning in
tcp_send_loss_probe() where packets_out is non-zero, but both transmit and retrans
queues are empty so we know the box is seeing some accounting issue in this area:
The NULL ptr deref is coming from tcp_rto_delta_us() attempting to pull an skb
off the head of the retransmit queue and then dereferencing that skb to get the
skb_mstamp_ns value via tcp_skb_timestamp_us(skb).
The crash is the same one that was reported a # of years ago here:
https://lore.kernel.org/netdev/86c0f836-9a7c-438b-d81a-839be45f1f58@gmail.com/T/#t
and the kernel we're running has the fix which was added to resolve this issue.
Unfortunately we've been unsuccessful so far in reproducing this problem in the
lab and do not have the luxury of pushing out a new kernel to try and test if
newer kernels resolve this issue at the moment. I realize this is a report
against both an Ubuntu kernel and also an older 5.4 kernel. I have reported this
issue to Ubuntu here: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2077657
however I feel like since this issue has possibly cropped up again it makes
sense to build in some protection in this path (even on the latest kernel
versions) since the code in question just blindly assumes there's a valid skb
without testing if it's NULL b/f it looks at the timestamp.
Given we have seen crashes in this path before and now this case it seems like
we should protect ourselves for when packets_out accounting is incorrect.
While we should fix that root cause we should also just make sure the skb
is not NULL before dereferencing it. Also add a warn once here to capture
some information if/when the problem case is hit again.
Fixes: e1a10ef7fa87 ("tcp: introduce tcp_rto_delta_us() helper for xmit timer fix") Signed-off-by: Josh Hunt <johunt@akamai.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rpl sr tunnel code contains calls to dst_cache_*() which are
only present when the dst cache is built.
Select DST_CACHE to build the dst cache, similar to other kconfig
options in the same file.
Compiling the rpl sr tunnel without DST_CACHE will lead to linker
errors.
Fixes: a7a29f9c361f ("net: ipv6: add rpl sr tunnel") Signed-off-by: Thomas Weißschuh <thomas.weissschuh@linutronix.de> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the ether3_probe function, a timer is initialized with a callback
function ether3_ledoff, bound to &prev(dev)->timer. Once the timer is
started, there is a risk of a race condition if the module or device
is removed, triggering the ether3_remove function to perform cleanup.
The sequence of operations that may lead to a UAF bug is as follows:
CPU0 CPU1
| ether3_ledoff
ether3_remove |
free_netdev(dev); |
put_devic |
kfree(dev); |
| ether3_outw(priv(dev)->regs.config2 |= CFG2_CTRLO, REG_CONFIG2);
| // use dev
Fix it by ensuring that the timer is canceled before proceeding with
the cleanup in ether3_remove.
Fixes: 6fd9c53f7186 ("net: seeq: Convert timers to use timer_setup()") Signed-off-by: Kaixin Wang <kxwang23@m.fudan.edu.cn> Link: https://patch.msgid.link/20240915144045.451-1-kxwang23@m.fudan.edu.cn Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
axienet_free_tx_chain returns the number of DMA descriptors it's
handled. However, axienet_tx_poll treats the return as the number of
packets. When scatter-gather SKBs are enabled, a single packet may use
multiple DMA descriptors, which causes incorrect packet counts. Fix this
by explicitly keepting track of the number of packets processed as
separate from the DMA descriptors.
Budget does not affect the number of Tx completions we can process for
NAPI, so we use the ring size as the limit instead of budget. As we no
longer return the number of descriptors processed to axienet_tx_poll, we
now update tx_bd_ci in axienet_free_tx_chain.
Fixes: 8a3b7a252dca ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by: Sean Anderson <sean.anderson@linux.dev> Link: https://patch.msgid.link/20240913145156.2283067-1-sean.anderson@linux.dev Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RX and TX byte/packet statistics in this driver could be overflowed
relatively quickly on a 32-bit platform. Switch these stats to use the
u64_stats infrastructure to avoid this.
This driver was using the TX IRQ handler to perform all TX completion
tasks. Under heavy TX network load, this can cause significant irqs-off
latencies (found to be in the hundreds of microseconds using ftrace).
This can cause other issues, such as overrunning serial UART FIFOs when
using high baud rates with limited UART FIFO sizes.
Switch to using a NAPI poll handler to perform the TX completion work
to get this out of hard IRQ context and avoid the IRQ latency impact.
A separate poll handler is used for TX and RX since they have separate
IRQs on this controller, so that the completion work for each of them
stays on the same CPU as the interrupt.
Testing on a Xilinx MPSoC ZU9EG platform using iperf3 from a Linux PC
through a switch at 1G link speed showed no significant change in TX or
RX throughput, with approximately 941 Mbps before and after. Hard IRQ
time in the TX throughput test was significantly reduced from 12% to
below 1% on the CPU handling TX interrupts, with total hard+soft IRQ CPU
usage dropping from about 56% down to 48%.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
The axienet_start_xmit function was updating the tx_bd_tail variable
multiple times, with potential rollbacks on error or invalid
intermediate positions, even though this variable is also used in the
TX completion path. Use READ_ONCE where this variable is read and
WRITE_ONCE where it is written to make this update more atomic, and
move the write before the MMIO write to start the transfer, so it is
protected by that implicit write barrier.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the ability to configure the RX/TX coalesce timer with ethtool.
Change default setting to scale with the clock rate rather than being a
fixed number of clock cycles.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
Now that NAPI has been implemented, the hardware interrupt mitigation
mechanism is not needed to avoid excessive interrupt load in most cases.
Reduce the default RX interrupt threshold to 1 to reduce introduced
latency. This can be increased with ethtool if desired if some applications
still want to reduce interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
Implement NAPI and GRO receive. In addition to better performance, this
also avoids handling RX packets in hard IRQ context, which reduces the
IRQ latency impact to other devices.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
When the RX or TX coalesce count is set to 1, there's no point in
setting the delay timer value since an interrupt will already be raised
on every packet, and the delay interrupt just causes extra pointless
interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5a6caa2cfabb ("net: xilinx: axienet: Fix packet counting") Signed-off-by: Sasha Levin <sashal@kernel.org>
The following sequence of commands causes a livelock - there will be
workqueue process looping and consuming 100% CPU:
dmsetup create --notable test
truncate -s 1MiB testdata
losetup /dev/loop0 testdata
dmsetup load test --table '0 2048 linear /dev/loop0 0'
dd if=/dev/zero of=/dev/dm-0 bs=16k count=1 conv=fdatasync
The livelock is caused by the commit fa247089de99. The commit claims that
it fixes a race condition, however, it is unknown what the actual race
condition is and what program is involved in the race condition.
When the inactive table is loaded, the nodes /dev/dm-0 and
/sys/block/dm-0 are created. /dev/dm-0 has zero size at this point. When
the device is suspended and resumed, the nodes /dev/mapper/test and
/dev/disk/* are created.
If some program opens a block device before it is created by dmsetup or
lvm, the program is buggy, so dm could just report an error as it used to
do before.
We used to call irq_bypass_unregister_producer() in
vhost_vdpa_setup_vq_irq() which is problematic as we don't know if the
token pointer is still valid or not.
Actually, we use the eventfd_ctx as the token so the life cycle of the
token should be bound to the VHOST_SET_VRING_CALL instead of
vhost_vdpa_setup_vq_irq() which could be called by set_status().
Fixing this by setting up irq bypass producer's token when handling
VHOST_SET_VRING_CALL and un-registering the producer before calling
vhost_vring_ioctl() to prevent a possible use after free as eventfd
could have been released in vhost_vring_ioctl(). And such registering
and unregistering will only be done if DRIVER_OK is set.
Reported-by: Dragos Tatulea <dtatulea@nvidia.com> Tested-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com> Fixes: 2cf1ba9a4d15 ("vhost_vdpa: implement IRQ offloading in vhost_vdpa") Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20240816031900.18013-1-jasowang@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This due to the fact that we do not free the "sg_table" itself while
freeing up the SG table and data pages. Fix this by freeing the sg_table
in tmc_free_sg_table().
Fixes: 99443ea19e8b ("coresight: Add generic TMC sg table framework") Cc: Mike Leach <mike.leach@linaro.org> Cc: James Clark <james.clark@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Link: https://lore.kernel.org/r/20240702132846.1677261-1-suzuki.poulose@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The binding's documentation specifies that "As the line is active low, it
should be marked GPIO_ACTIVE_LOW". However, in the driver, it was handled
the opposite way. This commit sets the driver's behaviour in sync with the
documentation
Fixes: 722407a4e8c0 ("staging:iio:ad7606: Use GPIO descriptor API") Signed-off-by: Guillaume Stols <gstols@baylibre.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
