The "usxgmii" phy-mode that the Felix switch ports support on LS1028A is
not quite USXGMII, it is defined by the USXGMII multiport specification
document as 10G-QXGMII. It uses the same signaling as USXGMII, but it
multiplexes 4 ports over the link, resulting in a maximum speed of 2.5G
per port.
This change is needed in preparation for the lynx-10g SerDes driver on
LS1028A, which will make a more clear distinction between usxgmii
(supported on lane 0) and 10g-qxgmii (supported on lane 1). These
protocols have their configuration in different PCCR registers (PCCRB vs
PCCR9).
Continue parsing and supporting single-port-per-lane USXGMII when found
in the device tree as usual (because it works), but add support for
10G-QXGMII too. Using phy-mode = "10g-qxgmii" will be required when
modifying the device trees to specify a "phys" phandle to the SerDes
lane. The result when the "phys" phandle is present but the phy-mode is
wrong is undefined.
The only PHY driver in known use with this phy-mode, AQR412C, will gain
logic to transition from "usxgmii" to "10g-qxgmii" in a future change.
Prepare the driver by also setting PHY_INTERFACE_MODE_10G_QXGMII in
supported_interfaces when PHY_INTERFACE_MODE_USXGMII is there, to
prevent breakage with existing device trees.
[Why]
dm_mst_get_pbn_divider() returns value integer coming from
the cast from fixed point, but the casted integer will then be used
in dfixed_const to be multiplied by 4096. The cast from fixed point to integer
causes the calculation error becomes bigger when multiplied by 4096.
That makes the calculated pbn_div value becomes smaller than
it should be, which leads to the req_slot number becomes bigger.
Such error is getting reflected in 8k30 timing,
where the correct and incorrect calculated req_slot 62.9 Vs 63.1.
That makes the wrong calculation failed to light up 8k30
after a dock under HBR3 x 4.
[How]
Restore the accuracy by keeping the fraction part
calculated for the left shift operation.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com> Signed-off-by: Wayne Lin <wayne.lin@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since SEV or SNP may already be initialized in the previous kernel,
attempting to initialize them again in the kdump kernel can result
in SNP initialization failures, which in turn lead to IOMMU
initialization failures. Moreover, SNP/SEV guests are not run under a
kdump kernel, so there is no need to initialize SEV or SNP during
kdump boot.
After a panic if SNP is enabled in the previous kernel then the kdump
kernel boots with IOMMU SNP enforcement still enabled.
IOMMU command buffers and event buffer registers remain locked and
exclusive to the previous kernel. Attempts to enable command and event
buffers in the kdump kernel will fail, as hardware ignores writes to
the locked MMIO registers as per AMD IOMMU spec Section 2.12.2.1.
Skip enabling command buffers and event buffers for kdump boot as they
are already enabled in the previous kernel.
After analysis, it appears this is because of the cond_resched()
call from __release_sock().
When current thread is yielding, while still holding the TCP socket lock,
it might regain the cpu after a very long time.
Other peer TLP/RTO is firing (multiple times) and packets are retransmit,
while the initial copy is waiting in the socket backlog or receive queue.
In this patch, I call cond_resched() only once every 16 packets.
Modern TCP stack now spends less time per packet in the backlog,
especially because ACK are no longer sent (commit 133c4c0d3717
"tcp: defer regular ACK while processing socket backlog")
The GuC communication protocol allows GuC to send NO_RESPONSE_RETRY
reply message to indicate that due to some interim condition it can
not handle incoming H2G request and the host shall resend it.
But in some cases, due to errors, this unsatisfied condition might
be final and this could lead to endless retries as it was recently
seen on the CI:
To avoid such dangerous loops allow only limited number of retries
(for now 50) and add some delays (n * 5ms) to slow down the rate of
resending this repeated request.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com> Cc: John Harrison <John.C.Harrison@Intel.com> Cc: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Stuart Summers <stuart.summers@intel.com> Reviewed-by: Julia Filipchuk <julia.filipchuk@intel.com> Link: https://lore.kernel.org/r/20250903223330.6408-1-michal.wajdeczko@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When the 3.3Vaux supply is present, fetch it at the probe time and keep it
enabled for the entire PCIe controller lifecycle so that the link can enter
L2 state and the devices can signal wakeup using either Beacon or WAKE#
mechanisms.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
[mani: reworded the subject, description and error message] Signed-off-by: Manivannan Sadhasivam <mani@kernel.org> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://patch.msgid.link/20250820022328.2143374-1-hongxing.zhu@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when adding the 6 GHz Band Capabilities element, the channel
list of the wiphy is checked to determine if 6 GHz is supported for a given
virtual interface. However, in a multi-radio wiphy (e.g., one that has
both lower bands and 6 GHz combined), the wiphy advertises support for
all bands. As a result, the 6 GHz Band Capabilities element is incorrectly
included in mesh beacon and station's association request frames of
interfaces operating in lower bands, without verifying whether the
interface is actually operating in a 6 GHz channel.
Fix this by verifying if the interface operates on 6 GHz channel
before adding the element. Note that this check cannot be placed
directly in ieee80211_put_he_6ghz_cap() as the same function is used to
add probe request elements while initiating scan in which case the
interface may not be operating in any band's channel.
Call the dedicated v4l2_disable_ioctl helper instead of manually
checking whether the current context is an encoder for the selection
api ioctls.
Signed-off-by: Paul Kocialkowski <paulk@sys-base.io> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The .querystd callback should not program the device with the detected
standard, it should only report the standard to user-space. User-space
may then use .s_std to set the standard, if it wants to use it.
All that is required of .querystd is to setup the auto detection of
standards and report its findings.
While at it add some documentation on why this can't happen while
streaming and improve the error handling using a scoped guard.
The .set_fmt callback should not write the new format directly do the
device, it should only store it and have it applied by .s_stream.
The .s_stream callback already calls adv7180_set_field_mode() so it's
safe to remove programming of the device and just store the format and
have .s_stream apply it.
The adv7180_set_power() utilizes adv7180_write() which in turn requires
the state mutex to be held, take it before calling adv7180_set_power()
to avoid tripping a lockdep_assert_held().
An exchange with a NFC target must complete within NCI_DATA_TIMEOUT.
A delay of 700 ms is not sufficient for cryptographic operations on smart
cards. CardOS 6.0 may need up to 1.3 seconds to perform 256-bit ECDH
or 3072-bit RSA. To prevent brute-force attacks, passports and similar
documents introduce even longer delays into access control protocols
(BAC/PACE).
The timeout should be higher, but not too much. The expiration allows
us to detect that a NFC target has disappeared.
Signed-off-by: Juraj Šarinay <juraj@sarinay.com> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://patch.msgid.link/20250902113630.62393-1-juraj@sarinay.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, having a valid panel_id match is required to use the quirk
system. For certain devices, we know that all SKUs need a certain quirk.
Therefore, allow not specifying ident by only checking for a match
if panel_id is non-zero.
Tested-by: Philip Müller <philm@manjaro.org> Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev> Link: https://lore.kernel.org/r/20250829145541.512671-2-lkml@antheas.dev Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ipv6_rpl_srh_rcv() we use min(net->ipv6.devconf_all->rpl_seg_enabled,
idev->cnf.rpl_seg_enabled) is intended to return 0 when either value is
zero, but if one of the values is negative it will in fact return non-zero.
rss_ctx.test_rss_key_indir implicitly expects at least 5 queues,
as it checks that the traffic on first 2 queues is lower than
the remaining queues when we use all queues. Special case fewer
queues.
The kfd CRIU checkpoint ioctl would return an error if trying
to checkpoint a process with no kfd buffer objects.
This is a normal case and should not be an error.
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: David Francis <David.Francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver unconditionally saves current state on first init in
dsi_pll_7nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_7nm_pll_restore_state().
Restoring calls dsi_pll_7nm_vco_set_rate() with
pll_7nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
According to Hardware Programming Guide for DSI PHY, the retime buffer
resync should be done after PLL clock users (byte_clk and intf_byte_clk)
are enabled. Downstream also does it as part of configuring the PLL.
Driver was only turning off the resync FIFO buffer, but never bringing it
on again.
DMA Engine has support for the callback_result which provides
the status of the request and the residue. This helps in
determining the correct status of the request and in
efficient resource management of the request.
The 'callback_result' method is preferred over the deprecated
'callback' method.
This patch modifies the type of setup_xref from void to int and handles
errors since the function can fail.
`setup_xref` now returns the (eventual) error from
`dmae_set_dmars`|`dmae_set_chcr`, while `shdma_tx_submit` handles the
result, removing the chunks from the queue and marking PM as idle in
case of an error.
Networking drivers implementing PTP clocks and kernel socket code
handling hardware timestamps use the 64-bit signed ktime_t type counting
nanoseconds. When a PTP clock reaches the maximum value in year 2262,
the timestamps returned to applications will overflow into year 1667.
The same thing happens when injecting a large offset with
clock_adjtime(ADJ_SETOFFSET).
The commit 7a8e61f84786 ("timekeeping: Force upper bound for setting
CLOCK_REALTIME") limited the maximum accepted value setting the system
clock to 30 years before the maximum representable value (i.e. year
2232) to avoid the overflow, assuming the system will not run for more
than 30 years.
Enforce the same limit for PTP clocks. Don't allow negative values and
values closer than 30 years to the maximum value. Drivers may implement
an even lower limit if the hardware registers cannot represent the whole
interval between years 1970 and 2262 in the required resolution.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <jstultz@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev> Link: https://patch.msgid.link/20250828103300.1387025-1-mlichvar@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On FSD platform, gating the reference clock (ref_clk) and putting the
UFS device in reset by asserting the reset signal during UFS suspend,
improves the power savings and ensures the PHY is fully turned off.
These operations are added as FSD specific suspend hook to avoid
unintended side effects on other SoCs supported by this driver.
Co-developed-by: Nimesh Sati <nimesh.sati@samsung.com> Signed-off-by: Nimesh Sati <nimesh.sati@samsung.com> Signed-off-by: Bharat Uppal <bharat.uppal@samsung.com> Link: https://lore.kernel.org/r/20250821053923.69411-1-bharat.uppal@samsung.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As noted in the kernel documentation [1], open-coded multiplication in
allocator arguments is discouraged because it can lead to integer overflow.
Use kcalloc() to gain built-in overflow protection, making memory
allocation safer when calculating allocation size compared to explicit
multiplication. Similarly, use size_add() instead of explicit addition
for 'uobj_chunk_num + sobj_chunk_num'.
Introduce support for standard MII ioctl operations in the LAN865x
Ethernet driver by implementing the .ndo_eth_ioctl callback. This allows
PHY-related ioctl commands to be handled via phy_do_ioctl_running() and
enables support for ethtool and other user-space tools that rely on ioctl
interface to perform PHY register access using commands like SIOCGMIIREG
and SIOCSMIIREG.
This feature enables improved diagnostics and PHY configuration
capabilities from userspace.
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: stp@e100bb0 (lantiq,gpio-stp-xway): $nodename:0: 'stp@e100bb0' does not match '^gpio@[0-9a-f]+$'
from schema $id: http://devicetree.org/schemas/gpio/gpio-stp-xway.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Bindig requires a node name matching ‘^gpio@[0-9a-f]+$’. This patch
changes the clock name from “stp” to “gpio”.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: pci@e105400 (lantiq,pci-xway): 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/pci/pci-bus-common.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warning:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: / (lantiq,xway): 'model' is a required property
from schema $id: http://devicetree.org/schemas/root-node.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes the following warnings:
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#address-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpus: '#size-cells' is a required property
from schema $id: http://devicetree.org/schemas/cpus.yaml#
arch/mips/boot/dts/lantiq/danube_easy50712.dtb: cpu@0 (mips,mips24Kc): 'reg' is a required property
from schema $id: http://devicetree.org/schemas/mips/cpus.yaml#
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Update the legacy (non-DC) display code to respect the maximum
pixel clock for HDMI and DVI-D. Reject modes that would require
a higher pixel clock than can be supported.
Also update the maximum supported HDMI clock value depending on
the ASIC type.
For reference, see the DC code:
check max_hdmi_pixel_clock in dce*_resource.c
v2:
Fix maximum clocks for DVI-D and DVI/HDMI adapters.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Timur Kristóf <timur.kristof@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why & How]
Previously, when calculating dto phase, we would incorrectly fail when phase
<=0 without additionally checking for the integer value. This meant that
calculations would incorrectly fail when the desired pixel clock was an exact
multiple of the reference clock.
Reviewed-by: Dillon Varone <dillon.varone@amd.com> Signed-off-by: Clay King <clayking@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
-Pipe splitting allows for clocks to be reduced, but when using TMDS 420,
reduced clocks lead to missed clocks cycles on clock resyncing
[How]
-Impose a minimum clock when using TMDS 420
Reviewed-by: Chris Park <chris.park@amd.com> Signed-off-by: Relja Vojvodic <rvojvodi@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can have modules in path which can change the number of channels and in
this case the BE params needs to be adjusted to configure the DAI according
to the copier configuration.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Seppo Ingalsuo <seppo.ingalsuo@linux.intel.com> Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com> Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Message-ID: <20250829105305.31818-2-peter.ujfalusi@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compare the whole v4l2_bt_timings struct, not just the width/height when
setting new timings. Timings with the same resolution and different
pixelclock can now be properly set.
Signed-off-by: Martin Tůma <martin.tuma@digiteqautomotive.com> Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 0d6ccfe6b319 ("selftests: drv-net: rss_ctx: check for all-zero keys")
added a skip exception if NIC has fewer than 3 queues enabled,
but it's just constructing the object, it's not actually rising
this exception.
Before:
# Exception| net.lib.py.utils.CmdExitFailure: Command failed: ethtool -X enp1s0 equal 3 hkey d1:cc:77:47:9d:ea:15:f2:b9:6c:ef:68:62:c0:45:d5:b0:99:7d:cf:29:53:40:06:3d:8e:b9:bc:d4:70:89:b8:8d:59:04:ea:a9:c2:21:b3:55:b8:ab:6b:d9:48:b4:bd:4c:ff:a5:f0:a8:c2
not ok 1 rss_ctx.test_rss_key_indir
After:
ok 1 rss_ctx.test_rss_key_indir # SKIP Device has fewer than 3 queues (or doesn't support queue stats)
A partitioned system configured with only one package and one compute
die, warning will be generated for duplicate sysfs entry. This typically
occurs during the platform bring-up phase.
Partitioned systems expose dies, equivalent to TPMI compute domains,
through the CPUID. Each partitioned system must contains at least one
compute die per partition, resulting in a minimum of two dies per
package. Hence the function topology_max_dies_per_package() returns at
least two, and the condition "topology_max_dies_per_package() > 1"
prevents the creation of a root domain.
In this case topology_max_dies_per_package() will return 1 and root
domain will be created for partition 0 and a duplicate sysfs warning
for partition 1 as both partitions have same package ID.
To address this also check for non zero partition in addition to
topology_max_dies_per_package() > 1.
When KFD asks CP to preempt queues, other than preempt CP queues, CP
also requests SDMA to preempt SDMA queues with UNMAP_LATENCY timeout.
Currently queue_preemption_timeout_ms is 9000 ms by default but can be
configured via module parameter. KFD_UNMAP_LATENCY_MS is hard coded as
4000 ms though. This patch ties KFD_UNMAP_LATENCY_MS to
queue_preemption_timeout_ms so in a slow system such as emulator, both
CP and SDMA slowness are taken into account.
Signed-off-by: Amber Lin <Amber.Lin@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
For the HW cursor, its current position in the pipe_ctx->stream struct is
not affected by the 180 rotation, i. e. the top left corner is still at
0,0. However, the DPP & HUBP set_cursor_position functions require rotated
position.
The current approach is hard-coded for ODM 2:1, thus it's failing for
ODM 4:1, resulting in a double cursor.
[How]
Instead of calculating the new cursor position relatively to the
viewports, we calculate it using a viewavable clip_rect of each plane.
The clip_rects are first offset and scaled to the same space as the
src_rect, i. e. Stream space -> Plane space.
In case of a pipe split, which divides the plane into 2 or more viewports,
the clip_rect is the union of all the viewports of the given plane.
With the assumption that the viewports in HUBP's set_cursor_position are
in the Plane space as well, it should produce a correct cursor position
for any number of pipe splits.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Signed-off-by: Ivan Lipski <ivan.lipski@amd.com> Signed-off-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Tested-by: Dan Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When it only allocates vram without va, which is 0, and a
SVM range allocated stays in this range, the vram allocation
returns failure. It should be skipped for this case from
SVM usage check.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com> Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Ce Sun <cesun102@amd.com> Reviewed-by: Yang Wang <kevinyang.wang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fixed_phy_register() creates and registers the phy_device. To be
symmetric, we should not only unregister, but also free the phy_device
in fixed_phy_unregister(). This allows to simplify code in users.
Note wrt of_phy_deregister_fixed_link():
put_device(&phydev->mdio.dev) and phy_device_free(phydev) are identical.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://patch.msgid.link/ad8dda9a-10ed-4060-916b-3f13bdbb899d@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Device can be unbound, so driver must also release memory for the wakeup
source. Do not use devm interface, because it would change the order of
cleanup.
Eliminate the use of static variables within the log pull implementation
to resolve a race condition and prevent data gaps when pulling logs from
multiple controllers in parallel, ensuring each operation is properly
isolated.
Firmware can enter a transient fault while creating operational queues.
The driver fails the load immediately.
Add a retry loop that checks controller status and history bit after
queue creation. If either indicates a fault, retry init up to a set
limit before failing.
Currently, ip_extract_route_hint uses RTN_BROADCAST to decide
whether to use the route dst hint mechanism.
This check is too strict, as it prevents directed broadcast
routes from using the hint, resulting in poor performance
during bursts of directed broadcast traffic.
Fix this in ip_extract_route_hint and modify ip_route_use_hint
to preserve the intended behaviour.
Module aliases are used by userspace to identify the correct module to
load for a detected hardware. The currently supported RPMSG device IDs for
this module include "rpmsg-raw", but the module alias is "rpmsg_chrdev".
Use the helper macro MODULE_DEVICE_TABLE(rpmsg) to export the correct
supported IDs. And while here, to keep backwards compatibility we also add
the other ID "rpmsg_chrdev" so that it is also still exported as an alias.
This has the side benefit of adding support for some legacy firmware
which still uses the original "rpmsg_chrdev" ID. This was the ID used for
this driver before it was upstreamed (as reflected by the module alias).
Signed-off-by: Andrew Davis <afd@ti.com> Acked-by: Hari Nagalla <hnagalla@ti.com> Tested-by: Hari Nagalla <hnagalla@ti.com> Link: https://lore.kernel.org/r/20250619205722.133827-1-afd@ti.com Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Just add fixed struct size validations for UAC2 and UAC3 effect
units. The descriptor has a variable-length array, so it should be
validated with a proper function later once when the unit is really
parsed and used by the driver (currently only referred partially for
the input terminal parsing).
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Make the following two changes:
(1) Replace -ENOMEM with -ENOSPC in max3100_probe().
(2) Just return -ENOMEM instead in max310x_probe().
The error handling path in pci_p2pdma_add_resource() contains a bug in its
`pgmap_free` label.
Memory is allocated for the `p2p_pgmap` struct, and the pointer is stored
in `p2p_pgmap`. However, the error path calls devm_kfree() with `pgmap`,
which is a pointer to a member field within the `p2p_pgmap` struct, not the
base pointer of the allocation.
Correct the bug by passing the correct base pointer, `p2p_pgmap`, to
devm_kfree().
As reported, on-disk footer.ino and footer.nid is the same and
out-of-range, let's add sanity check on f2fs_alloc_nid() to detect
any potential corruption in free_nid_list.
Initially, trace_sock_exceed_buf_limit() was invoked when
__sk_mem_raise_allocated() failed due to the memcg limit or the
global limit.
However, commit d6f19938eb031 ("net: expose sk wmem in
sock_exceed_buf_limit tracepoint") somehow suppressed the event
only when memcg failed to charge for SK_MEM_RECV, although the
memcg failure for SK_MEM_SEND still triggers the event.
The stmmac_rx function would previously set skb->ip_summed to
CHECKSUM_UNNECESSARY if hardware checksum offload (CoE) was enabled
and the packet was of a known IP ethertype.
However, this logic failed to check if the hardware had actually
reported a checksum error. The hardware status, indicating a header or
payload checksum failure, was being ignored at this stage. This could
cause corrupt packets to be passed up the network stack as valid.
This patch corrects the logic by checking the `csum_none` status flag,
which is set when the hardware reports a checksum error. If this flag
is set, skb->ip_summed is now correctly set to CHECKSUM_NONE,
ensuring the kernel's network stack will perform its own validation and
properly handle the corrupt packet.
When removing a nexthop, commit 90f33bffa382 ("nexthops: don't modify published nexthop groups") added a
call to synchronize_rcu() (later changed to _net()) to make sure
everyone sees the new nexthop-group before the rtnl-lock is released.
When one wants to delete a large number of groups and nexthops, it is
fastest to first flush the groups (ip nexthop flush groups) and then
flush the nexthops themselves (ip -6 nexthop flush). As that way the
groups don't need to be rebalanced.
However, `ip -6 nexthop flush` will still take a long time if there is
a very large number of nexthops because of the call to
synchronize_net(). Now, if there are no more groups, there is no point
in calling synchronize_net(). So, let's skip that entirely by checking
if nh->grp_list is empty.
This gives us a nice speedup:
BEFORE:
=======
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 2097152 nexthops
real 1m45.345s
user 0m0.001s
sys 0m0.005s
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 4194304 nexthops
real 3m10.430s
user 0m0.002s
sys 0m0.004s
AFTER:
======
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 2097152 nexthops
real 0m17.545s
user 0m0.003s
sys 0m0.003s
$ time sudo ip -6 nexthop flush
Dump was interrupted and may be inconsistent.
Flushed 4194304 nexthops
real 0m35.823s
user 0m0.002s
sys 0m0.004s
Signed-off-by: Christoph Paasch <cpaasch@openai.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://patch.msgid.link/20250816-nexthop_dump-v2-2-491da3462118@openai.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
misc_open() may request module for miscdevice with dynamic minor, which
is meaningless since:
- The dynamic minor allocated is unknown in advance without registering
miscdevice firstly.
- Macro MODULE_ALIAS_MISCDEV() is not applicable for dynamic minor.
Fix by only requesting module for miscdevice with fixed minor.
For miscdevice who wants dynamic minor, it may fail to be registered again
without reinitialization after being de-registered, which is illustrated
by kunit test case miscdev_test_dynamic_reentry() newly added.
There is a real case found by cascardo when a part of minor range were
contained by range [0, 255):
1) wmi/dell-smbios registered minor 122, and acpi_thermal_rel registered
minor 123
2) unbind "int3400 thermal" driver from its device, this will de-register
acpi_thermal_rel
3) rmmod then insmod dell_smbios again, now wmi/dell-smbios is using minor
123
4) bind the device to "int3400 thermal" driver again, acpi_thermal_rel
fails to register.
Some drivers may reuse the miscdevice structure after they are deregistered
If the intention is to allocate a dynamic minor, if the minor number is not
reset to MISC_DYNAMIC_MINOR before calling misc_register(), it will try to
register a previously dynamically allocated minor number, which may have
been registered by a different driver.
One such case is the acpi_thermal_rel misc device, registered by the
int3400 thermal driver. If the device is unbound from the driver and later
bound, if there was another dynamic misc device registered in between, it
would fail to register the acpi_thermal_rel misc device. Other drivers
behave similarly.
Actually, this kind of issue is prone to happen if APIs
misc_register()/misc_deregister() are invoked by driver's
probe()/remove() separately.
Instead of fixing all the drivers, just reset the minor member to
MISC_DYNAMIC_MINOR in misc_deregister() in case it was a dynamically
allocated minor number, as error handling of misc_register() does.
Mark dm error as DM_TARGET_PASSES_INTEGRITY so that it can be stacked on
top of PI capable devices. The claim is strictly speaking as lie as dm
error fails all I/O and doesn't pass anything on, but doing the same for
integrity I/O work just fine :)
This helps to make about two dozen xfstests test cases pass on PI capable
devices.
In WoWLAN net-detect mode, the firmware periodically performs scans
and sends scan reports via C2H, which driver does not need. These
unnecessary C2H events cause firmware watchdog timeout, leading
to unexpected wakeups and SER 0x2599 on 8922AE.
This fix is already present in f_ecm.c and was never
propagated to f_ncm.c
When creating multiple NCM ethernet devices
on a composite usb gadget device
each MAC address on the HOST side will be identical.
Having the same MAC on different network interfaces is bad.
This fix updates the MAC address inside the
ncm_strings_defs global during the ncm_bind call.
This ensures each device has a unique MAC.
In f_ecm.c ecm_string_defs is updated in the same way.
The defunct MAC assignment in ncm_alloc has been removed.
ADC calibration might fail because of the noise on reference voltage.
To avoid calibration fail, need to meet the following requirement:
ADC reference voltage Noise < 1.8V * 1/2^ENOB
For the case which the ADC reference voltage on board do not meet
the requirement, still load the calibrated values, so ADC can also
work but maybe not that accurate.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Reviewed-by: Primoz Fiser <primoz.fiser@norik.com> Link: https://patch.msgid.link/20250812-adc-v2-2-0260833f13b8@nxp.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
HMM assumes that pages have READ permissions by default. Inside
svm_range_validate_and_map, we add READ permissions then add WRITE
permissions if the VMA isn't read-only. This will conflict with regions
that only have PROT_WRITE or have PROT_NONE. When that happens,
svm_range_restore_work will continue to retry, silently, giving the
impression of a hang if pr_debug isn't enabled to show the retries..
If pages don't have READ permissions, simply unmap them and continue. If
they weren't mapped in the first place, this would be a no-op. Since x86
doesn't support write-only, and PROT_NONE doesn't allow reads or writes
anyways, this will allow the svm range validation to continue without
getting stuck in a loop forever on mappings we can't use with HMM.
Signed-off-by: Kent Russell <kent.russell@amd.com> Reviewed-by: Felix Kuehling <felix.kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a amdgpu_bo_va is fpriv->prt_va, the bo of this one is always NULL.
So, such kind of amdgpu_bo_va should be updated separately before
amdgpu_vm_handle_moved.
Detecting the monitor for DisplayPort targets is more complicated than
just reading the HPD pin level: it requires reading the DPCD in order to
check what kind of device is attached to the port and whether there is
an actual display attached.
In order to let DRM framework handle such configurations, disable
DRM_BRIDGE_OP_DETECT for dp-connector devices, letting the actual DP
driver perform detection. This still keeps DRM_BRIDGE_OP_HPD enabled, so
it is valid for the bridge to report HPD events.
Currently inside the kernel there are only two targets which list
hpd-gpios for dp-connector devices: arm64/qcom/qcs6490-rb3gen2 and
arm64/qcom/sa8295p-adp. Both should be fine with this change.
The already fixed bug in SDL only affected conditional effects. This
should fix FFB in Forza Horizion 4/5 on Moza Devices as Forza Horizon
flips the constant force direction instead of using negative magnitude
values.
Changing the direction in the effect directly in pidff_upload_effect()
would affect it's value in further operations like comparing to the old
effect and/or just reading the effect values in the user application.
This, in turn, would lead to constant PID_SET_EFFECT spam as the effect
direction would constantly not match the value that's set by the
application.
This way, it's still transparent to any software/API.
Only affects conditional effects now so it's better for it to explicitly
state that in the name. If any HW ever needs fixed direction for other
effects, we'll add more quirks.
In certain scenarios, it is possible for multiple cache flushes to be
requested before the previous one completes. This patch introduces the
cache_flush_lock mutex to serialize these operations and ensure that
any requested cache flushes are completed instead of dropped.
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> Co-developed-by: Dennis Tsiang <dennis.tsiang@arm.com> Signed-off-by: Dennis Tsiang <dennis.tsiang@arm.com> Signed-off-by: Karunika Choo <karunika.choo@arm.com> Reviewed-by: Steven Price <steven.price@arm.com> Signed-off-by: Steven Price <steven.price@arm.com> Link: https://lore.kernel.org/r/20250807162633.3666310-6-karunika.choo@arm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting that imon has three problems which result in
hung tasks due to forever holding device lock [1].
First problem is that when usb_rx_callback_intf0() once got -EPROTO error
after ictx->dev_present_intf0 became true, usb_rx_callback_intf0()
resubmits urb after printk(), and resubmitted urb causes
usb_rx_callback_intf0() to again get -EPROTO error. This results in
printk() flooding (RCU stalls).
Alan Stern commented [2] that
In theory it's okay to resubmit _if_ the driver has a robust
error-recovery scheme (such as giving up after some fixed limit on the
number of errors or after some fixed time has elapsed, perhaps with a
time delay to prevent a flood of errors). Most drivers don't bother to
do this; they simply give up right away. This makes them more
vulnerable to short-term noise interference during USB transfers, but in
reality such interference is quite rare. There's nothing really wrong
with giving up right away.
but imon has a poor error-recovery scheme which just retries forever;
this behavior should be fixed.
Since I'm not sure whether it is safe for imon users to give up upon any
error code, this patch takes care of only union of error codes chosen from
modules in drivers/media/rc/ directory which handle -EPROTO error (i.e.
ir_toy, mceusb and igorplugusb).
Second problem is that when usb_rx_callback_intf0() once got -EPROTO error
before ictx->dev_present_intf0 becomes true, usb_rx_callback_intf0() always
resubmits urb due to commit 8791d63af0cf ("[media] imon: don't wedge
hardware after early callbacks"). Move the ictx->dev_present_intf0 test
introduced by commit 6f6b90c9231a ("[media] imon: don't parse scancodes
until intf configured") to immediately before imon_incoming_packet(), or
the first problem explained above happens without printk() flooding (i.e.
hung task).
Third problem is that when usb_rx_callback_intf0() is not called for some
reason (e.g. flaky hardware; the reproducer for this problem sometimes
prevents usb_rx_callback_intf0() from being called),
wait_for_completion_interruptible() in send_packet() never returns (i.e.
hung task). As a workaround for such situation, change send_packet() to
wait for completion with timeout of 10 seconds.
Fix field-spanning memcpy warnings in ah6_output() and
ah6_output_done() where extension headers are copied to/from IPv6
address fields, triggering fortify-string warnings about writes beyond
the 16-byte address fields.
memcpy: detected field-spanning write (size 40) of single field "&top_iph->saddr" at net/ipv6/ah6.c:439 (size 16)
WARNING: CPU: 0 PID: 8838 at net/ipv6/ah6.c:439 ah6_output+0xe7e/0x14e0 net/ipv6/ah6.c:439
The warnings are false positives as the extension headers are
intentionally placed after the IPv6 header in memory. Fix by properly
copying addresses and extension headers separately, and introduce
helper functions to avoid code duplication.
Add a NULL check before accessing the 'vccqx' pointer to prevent invalid
memory access. This ensures that the function safely handles cases where
'vccq' and 'vccq2' are not initialized, improving the robustness of the
power management code.
Signed-off-by: Alice Chao <alice.chao@mediatek.com> Reviewed-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Peter Wang <peter.wang@mediatek.com> Link: https://lore.kernel.org/r/20250811131423.3444014-11-peter.wang@mediatek.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Modify the reset sequence to ensure that the device reset pin is set low
before the host is disabled. This change enhances the stability of the
reset process by ensuring the correct order of operations.
Assign power mode userdata settings before transitioning to FASTAUTO
power mode. This ensures that default timeout values are set for various
parameters, enhancing the reliability and performance of the power mode
change process.
Signed-off-by: Alice Chao <alice.chao@mediatek.com> Reviewed-by: Peter Wang <peter.wang@mediatek.com> Signed-off-by: Peter Wang <peter.wang@mediatek.com> Link: https://lore.kernel.org/r/20250811131423.3444014-7-peter.wang@mediatek.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Address a failure in switching to PWM mode by ensuring proper
configuration of power modes and adaptation settings. The changes
include checks for SLOW_MODE and adjustments to the desired working mode
and adaptation configuration based on the device's power mode and
hardware version.
Move the configuration of the Auto-Hibern8 (AHIT) timer from the
post-link stage to the 'fixup_dev_quirks' function. This change allows
setting the AHIT based on the vendor requirements:
(a) Samsung: 3.5 ms
(b) Micron: 2 ms
(c) Others: 1 ms
Additionally, the clock gating timer is adjusted based on the AHIT
scale, with a maximum setting of 10 ms. This ensures that the clock
gating delay is appropriately configured to match the AHIT settings.
If a backup port is configured for a bridge port, the bridge will
redirect known unicast traffic towards the backup port when the primary
port is administratively up but without a carrier. This is useful, for
example, in MLAG configurations where a system is connected to two
switches and there is a peer link between both switches. The peer link
serves as the backup port in case one of the switches loses its
connection to the multi-homed system.
In order to avoid flooding when the primary port loses its carrier, the
bridge does not flush dynamic FDB entries pointing to the port upon STP
disablement, if the port has a backup port.
The above means that known unicast traffic destined to the primary port
will be blackholed when the port is put administratively down, until the
FDB entries pointing to it are aged-out.
Given that the current behavior is quite weird and unlikely to be
depended on by anyone, amend the bridge to redirect to the backup port
also when the primary port is administratively down and not only when it
does not have a carrier.
The change is motivated by a report from a user who expected traffic to
be redirected to the backup port when the primary port was put
administratively down while debugging a network issue.
Reviewed-by: Petr Machata <petrm@nvidia.com> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250812080213.325298-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ever since uevent support was added for AER and EEH with commit 856e1eb9bdd4 ("PCI/AER: Add uevents in AER and EEH error/resume"), it
reported PCI_ERS_RESULT_NONE as uevent when recovery begins.
Commit 7b42d97e99d3 ("PCI/ERR: Always report current recovery status for
udev") subsequently amended AER to report the actual return value of
error_detected().
Make the same change to EEH to align it with AER and s390.
projects / thirdparty / kernel / stable.git / log
