In the case where the dma_iv mapping fails, the return error path leaks
the memory allocated to object d. Fix this by adding a new error return
label and jumping to this to ensure d is free'd before the return.
Addresses-Coverity: ("Resource leak") Fixes: ac2614d721de ("crypto: sun8i-ss - Add support for the PRNG") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
WSA881x powerdown pin is connected to GPIO1 not gpio2, so correct this.
This was working so far due to a shift bug in gpio driver, however
once that is fixed this will stop working, so fix this!
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
At boot time the following happens:
1. Device core gets ready to probe our SPI driver.
2. Device core applies SPI controller's "default" pinctrl.
3. Device core calls the SPI driver's probe() function which will
eventually setup the chip select GPIO as "unasserted".
Thinking about the above, we can find:
a) For SPI devices that the BIOS inits (Cr50 and EC), the BIOS would
have had them configured as "GENI" pins and not as "GPIO" pins.
b) It turns out that our BIOS also happens to init these pins as
"output" (even though it doesn't need to since they're not muxed as
GPIO) but leaves them at the default state of "low".
c) As soon as we apply the "default" chip select it'll switch the
function to GPIO and stop driving the chip select high (which is
how "GENI" was driving it) and start driving it low.
d) As of commit 9378f46040be ("UPSTREAM: spi: spi-geni-qcom: Use the
new method of gpio CS control"), when the SPI core inits things it
inits the GPIO to be "deasserted". Prior to that commit the GPIO
was left untouched until first use.
e) When the first transaction happens we'll assert the chip select and
then deassert it after done.
So before the commit to change us to use gpio descriptors we used to
have a _really long_ assertion of chip select before our first
transaction (because it got pulled down and then the first "assert"
was a no-op). That wasn't great but (apparently) didn't cause any
real harm.
After the commit to change us to use gpio descriptors we end up
glitching the chip select line during probe. It would go low and then
high with no data transferred. The other side ought to be robust
against this, but it certainly could cause some confusion. It's known
to at least cause an error message on the EC console and it's believed
that, under certain timing conditions, it could be getting the EC into
a confused state causing the EC driver to fail to probe.
Let's fix things to avoid the glitch. We'll add an extra pinctrl
entry that sets the value of the pin to output high (CS deasserted)
before doing anything else. We'll do this in its own pinctrl node
that comes before the normal pinctrl entries to ensure that the order
is correct and that this gets applied before the mux change.
This change is in the trogdor board file rather than in the SoC dtsi
file because chip select polarity can be different depending on what's
hooked up and it doesn't feel worth it to spam the SoC dtsi file with
both options. The board file would need to pick the right one anyway.
Reviewed-by: Stephen Boyd <swboyd@chromium.org> Fixes: cfbb97fde694 ("arm64: dts: qcom: Switch sc7180-trogdor to control SPI CS via GPIO") Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20210218145456.1.I1da01a075dd86e005152f993b2d5d82dd9686238@changeid Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ARM architected timer interrupts DT property specifies EL2/HYP
physical interrupt and not EL2/HYP virtual interrupt for the 4th
interrupt property. As per interrupt documentation for SM8250 SoC,
the EL2/HYP physical timer interrupt is 10 and EL2/HYP virtual timer
interrupt is 12, so fix the 4th timer interrupt to be EL2 physical
timer interrupt (10 in this case).
When using PPS mode, the input clock needs to be scaled so that we have
an IMU sample rate between (optimally) 4000 and 4250. After this, we can
use the decimation filter to lower the sampling rate in order to get what
the user wants. Optimally, the user sample rate is a multiple of both the
IMU sample rate and the input clock. Hence, calculating the sync_scale
dynamically gives us better chances of achieving a perfect/integer value
for DEC_RATE. The math here is:
1. lcm of the input clock and the desired output rate.
2. get the highest multiple of the previous result lower than the adis
max rate.
3. The last result becomes the IMU sample rate. Use that to calculate
SYNC_SCALE and DEC_RATE (to get the user output rate).
Fixes: 326e2357553d3 ("iio: imu: adis16480: Add support for external clock") Signed-off-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210218114039.216091-2-nuno.sa@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to latest errata of J721e [1], HS400 mode is not supported
in MMCSD0 subsystem (i2024) and SDR104 mode is not supported in MMCSD1/2
subsystems (i2090). Therefore, replace mmc-hs400-1_8v with mmc-hs200-1_8v
in MMCSD0 subsystem and add a sdhci mask to disable SDR104 speed mode.
Also, update the itap delay values for all the MMCSD subsystems according
the latest J721e data sheet[2]
Modify usart 2 & 3 pins to allow wake up from low power mode while the
hardware flow control is activated. UART RTS pin need to stay configure
in idle mode to receive characters in order to wake up.
When platform_get_drvdata() returns NULL to info, no error return code
of physmap_flash_remove() is assigned.
To fix this bug, err is assigned with -EINVAL in this case
In qcom_probe_nand_devices() function, the error code returned by
qcom_nand_host_init_and_register() is converted to -ENODEV in the case
of failure. This poses issue if -EPROBE_DEFER is returned when the
dependency is not available for a component like parser.
So let's restructure the error handling logic a bit and return the
actual error code in case of qcom_nand_host_init_and_register() failure.
There are chances that the parse_mtd_partitions() function will return
-EPROBE_DEFER in mtd_device_parse_register(). This might happen when
the dependency is not available for the parser. For instance, on SDX55
the MTD_QCOMSMEM_PARTS parser depends on the QCOM_SMEM driver to parse
the partitions defined in the shared memory region. With the current
flow, the error returned from parse_mtd_partitions() will be discarded
in favor of trying to add the fallback partition.
This will prevent the driver to end up in probe deferred pool and the
partitions won't be parsed even after the QCOM_SMEM driver is available.
Fix this issue by bailing out of mtd_device_parse_register() when
-EPROBE_DEFER error is returned from parse_mtd_partitions() function and
propagate the error code to the driver core for probing later.
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
There is a upstream commit cffa4b2122f5("regmap:debugfs:
Fix a memory leak when calling regmap_attach_dev") that
adds a if condition when create name for debugfs_name.
With below function invoking logical, debugfs_name is
freed in regmap_debugfs_exit(), but it is not created again
because of the if condition introduced by above commit.
regmap_reinit_cache()
regmap_debugfs_exit()
...
regmap_debugfs_init()
So, set debugfs_name to NULL after it is freed.
Fixes: cffa4b2122f5 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev") Signed-off-by: Meng Li <Meng.Li@windriver.com> Link: https://lore.kernel.org/r/20210226021737.7690-1-Meng.Li@windriver.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some products will be available that have PMT capabilities that are not
supported. Remove the warnings in this instance to avoid nuisance messages
and confusion.
Also return an error code for capabilities that are disabled by quirk to
prevent them from keeping the driver loaded if only disabled capabilities
are found.
Fixes: 4f8217d5b0ca ("mfd: Intel Platform Monitoring Technology support") Signed-off-by: David E. Box <david.e.box@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function device_get_named_child_node() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: da0cb6310094 ("usb: typec: add support for STUSB160x Type-C controller family") Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20210308094839.3586773-1-weiyongjun1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function device_get_named_child_node() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Fixes: 18a6c866bb19 ("usb: typec: tps6598x: Add USB role switching logic") Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Link: https://lore.kernel.org/r/20210308094841.3587751-1-weiyongjun1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While interpreting CC_STATUS, ROLE_CONTROL has to be read to make
sure that CC1/CC2 is not forced presenting Rp/Rd.
>From the TCPCI spec:
4.4.5.2 ROLE_CONTROL (Normative):
The TCPM shall write B6 (DRP) = 0b and B3..0 (CC1/CC2) if it wishes
to control the Rp/Rd directly instead of having the TCPC perform
DRP toggling autonomously. When controlling Rp/Rd directly, the
TCPM writes to B3..0 (CC1/CC2) each time it wishes to change the
CC1/CC2 values. This control is used for TCPM-TCPC implementing
Source or Sink only as well as when a connection has been detected
via DRP toggling but the TCPM wishes to attempt Try.Src or Try.Snk.
While in source mode, vbus could be shutoff by protections
circuits. TCPM does not move back to toggling state to
re-initiate connection. Fix this by moving to SRC_UNATTACHED
state when vbus shuts off while in source mode.
In "tx_empty", we should poll TC bit in both DMA and PIO modes (instead of
TXE) to check transmission data register has been transmitted independently
of the FIFO mode. TC indicates that both transmit register and shift
register are empty. When shift register is empty, tx_empty should return
TIOCSER_TEMT instead of TC value.
Cleans the USART_CR_TC TCCF register define (transmission complete clear
flag) as it is duplicate of USART_ICR_TCCF.
Transmission complete error is sent when ISR_TC is not set. If port closure
is requested despite data in TDR / TX FIFO has not been sent (because of
flow control), ISR_TC is not set and error message is sent on port closure
but also when a new port is opened.
Flush the data when port is closed, so the error isn't printed twice upon
next port opening.
Fixes: 64c32eab6603 ("serial: stm32: Add support of TC bit status check") Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Link: https://lore.kernel.org/r/20210304162308.8984-12-erwan.leray@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fifo flush set USART_RQR register by calling stm32_usart_set_bits
routine (Read/Modify/Write). USART_RQR register is a write only
register. So, read before write isn't correct / relevant to flush
the FIFOs.
Replace stm32_usart_set_bits call by writel_relaxed.
Fixes: 84872dc448fe ("serial: stm32: add RX and TX FIFO flush") Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Link: https://lore.kernel.org/r/20210304162308.8984-11-erwan.leray@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of error, the function devm_platform_get_and_ioremap_resource()
returns ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
CTS/RTS GPIOs support that has been added recently to STM32 UART driver has
introduced scheduled code in a set_termios part protected by a spin lock.
This generates a potential deadlock scenario:
This patch fixes several issue with wake-up handling:
- the WUF irq is handled several times at wake-up
- the USART is disabled / enabled at suspend to set wake-up flag.
It can cause glitches during RX.
This patch fix those issues:
- clear wake-up flag and disable wake-up irq in WUF irq handling
- enable wake-up from low power on start bit detection at port
configuration
- Unmask the wake-up flag irq at suspend and mask it at resume
In addition, pm_wakeup_event handling is moved from receice_chars to WUF
irq handling.
Deadlock issue is seen when enabling CONFIG_PROVE_LOCKING=Y, and uart
console as wakeup source. Deadlock occurs when resuming from low power
mode if system is waked up via usart console.
The deadlock is triggered 100% when also disabling console suspend prior
to go to suspend.
Simplified call stack, deadlock condition:
- stm32_console_write <-- spin_lock already held
- print_circular_bug
- pm_wakeup_dev_event <-- triggers lockdep as seen above
- stm32_receive_chars
- stm32_interrupt <-- wakeup via uart console, takes the lock
So, revisit spin_lock in stm32-usart driver:
- there is no need to hold the lock to access ICR (atomic clear of status
flags)
- only hold the lock inside stm32_receive_chars() routine (no need to
call pm_wakeup_dev_event with lock held)
- keep stm32_transmit_chars() routine called with lock held
TX and RX FIFO thresholds may be cleared after suspend/resume, depending
on the low power mode.
Those configurations (done in startup) are not effective for UART console,
as:
- the reference manual indicates that FIFOEN bit can only be written when
the USART is disabled (UE=0)
- a set_termios (where UE is set) is requested firstly for console
enabling, before the startup.
Fixes: 84872dc448fe ("serial: stm32: add RX and TX FIFO flush") Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Link: https://lore.kernel.org/r/20210304162308.8984-5-erwan.leray@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Incorrect characters are observed on console during boot. This issue occurs
when init/main.c is modifying termios settings to open /dev/console on the
rootfs.
This patch adds a waiting loop in set_termios to wait for TX shift register
empty (and TX FIFO if any) before stopping serial port.
RX is configured, but usart is not enabled in startup function.
Kernel documentation specifies that startup should enable the port for
reception.
Fix the startup by enabling usart for reception.
Fixes: 84872dc448fe ("serial: stm32: add RX and TX FIFO flush") Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Link: https://lore.kernel.org/r/20210304162308.8984-3-erwan.leray@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver casts away the constness of struct stm32_usart_info that is
pointed to by the of match table. Use of_device_get_match_data() instead
of of_match_device() here and push the const throughout the code so that
we don't cast away const. This nicely avoids referencing the match table
when it is undefined with configurations where CONFIG_OF=n and fixes the
const issues.
The probe and remove orders are wrong as the uart_port is registered
before saving device data in the probe, and unregistered after DMA
resource deallocation in the remove. uart_port registering should be
done at the end of probe and unregistering should be done at the begin of
remove to avoid resource allocation issues.
Fix probe and remove orders. This enforce resource allocation occur at
proper time.
Terminate both DMA rx and tx transfers before removing device.
Move pm_runtime after uart_remove_one_port() call in remove() to keep the
probe error path.
Adds the prefix "_usart" in the name of stm32 usart functions in order to
ease the usage of kernel trace and tools, such as f-trace.
Allows to trace "stm32_usart_*" functions with f-trace. Without this patch,
all the driver functions needs to be added manually in f-trace filter.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Signed-off-by: Valentin Caron <valentin.caron@foss.st.com> Link: https://lore.kernel.org/r/20210106162203.28854-4-erwan.leray@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes checkpatch --strict warnings and checks:
- checkpatch --strict "Unnecessary parentheses"
- checkpatch --strict "Blank lines aren't necessary before a close brace
- checkpatch --strict "Alignment should match open parenthesis"
- checkpatch --strict "Please don't use multiple blank lines"
- checkpatch --strict "Comparison to NULL could be written ..."
- visual check code ordering warning
bbbd2b51a2aa ("x86/platform/UV: Use new set memory block size function")
added a call to set the block size value that is needed by the kernel
to set the boundaries in the section list. This was done for UV Hubbed
systems but missed in the UV Hubless setup. Fix that mistake by adding
that same set call for hubless systems, which support the same NVRAMs
and Intel BIOS, thus the same problem occurs.
[ bp: Massage commit message. ]
Fixes: bbbd2b51a2aa ("x86/platform/UV: Use new set memory block size function") Signed-off-by: Mike Travis <mike.travis@hpe.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Steve Wahl <steve.wahl@hpe.com> Reviewed-by: Russ Anderson <rja@hpe.com> Link: https://lkml.kernel.org/r/20210305162853.299892-1-mike.travis@hpe.com Signed-off-by: Sasha Levin <sashal@kernel.org>
We have interconnect target modules with no known registers using only
clocks and resets, but we still want to detect them based on the module
IO range. So let's call sysc_parse_and_check_child_range() earlier so we
have module_pa properly initialized.
Fixes: 2928135c93f8 ("bus: ti-sysc: Support modules without control registers") Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After the commit 7320915c8861 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS
for drivers that existed in v4.14"), the order of /dev/mmcblkN
was not fixed in some SoCs which have multiple sdhi controllers.
So, we were hard to use an sdhi device as rootfs by using
the kernel parameter like "root=/dev/mmcblkNpM".
According to the discussion on a mainling list [1], we can add
mmc aliases to fix the issue. So, add such aliases into Renesas
arm64 board dts files. Notes that mmc0 is an eMMC channel if
available.
After set PROBE_PREFER_ASYNCHRONOUS flag on the mmc host drivers,
the order of /dev/mmcblkN was not fixed in some SoCs which have
multiple SDHI and/or MMCIF controllers. So, we were hard to use
such a device as rootfs by using the kernel parameter like
"root=/dev/mmcblkNpM".
According to the discussion on a mainling list [1], we can add
mmc aliases to fix the issue. So, add such aliases into R-Car Gen2
board dts files. Note that, since R-Car Gen2 is even more complicated
about SDHI and/or MMCIF channels variations and they share pins,
add the aliases into board dts files instead of SoC dtsi files.
Fixes: 7320915c8861 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.14") Fixes: 21b2cec61c04 ("mmc: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in v4.4") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Link: https://lore.kernel.org/r/1613131316-30994-1-git-send-email-yoshihiro.shimoda.uh@renesas.com Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
Fixes: 47580e8d94c2 ("ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20201210212534.216197-8-krzk@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
The Maxim PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
The Maxim MUIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Additionally, the interrupt line is shared so using level sensitive
interrupt is here especially important to avoid races.
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
The Maxim fuel gauge datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU. The falling edge
interrupt will mostly work but it's not correct.
Currently the array gpmc_cs is indexed by cs before it cs is range checked
and the pointer read from this out-of-index read is dereferenced. Fix this
by performing the range check on cs before the read and the following
pointer dereference.
Addresses-Coverity: ("Negative array index read") Fixes: 9ed7a776eb50 ("ARM: OMAP2+: Fix support for multiple devices on a GPMC chip select") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20210223193821.17232-1-colin.king@canonical.com Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
8382c668ce4f ("x86/vdso: Add support for exception fixup in vDSO functions")
prints length "len" which is size_t.
Compilers now complain when building on a 32-bit host:
HOSTCC arch/x86/entry/vdso/vdso2c
...
In file included from arch/x86/entry/vdso/vdso2c.c:162:
arch/x86/entry/vdso/vdso2c.h: In function 'extract64':
arch/x86/entry/vdso/vdso2c.h:38:52: warning: format '%lu' expects argument of \
type 'long unsigned int', but argument 4 has type 'size_t' {aka 'unsigned int'}
So use proper modifier (%zu) for size_t.
[ bp: Massage commit message. ]
Fixes: 8382c668ce4f ("x86/vdso: Add support for exception fixup in vDSO functions") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Jarkko Sakkinen <jarkko@kernel.org> Link: https://lkml.kernel.org/r/20210303064357.17056-1-jslaby@suse.cz Signed-off-by: Sasha Levin <sashal@kernel.org>
zynqmp_pm_get_eemi_ops() was removed in commit 4db8180ffe7c: "Firmware: xilinx:
Remove eemi ops for fpga related APIs", but not in IS_REACHABLE(CONFIG_ZYNQMP_FIRMWARE).
Any driver who want to communicate with PMC using EEMI APIs use the functions provided
for each function
This removed zynqmp_pm_get_eemi_ops() in IS_REACHABLE(CONFIG_ZYNQMP_FIRMWARE), and also
modify the documentation for this driver.
Fixes: 4db8180ffe7c ("firmware: xilinx: Remove eemi ops for fpga related APIs") Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Link: https://lore.kernel.org/r/20210215155849.2425846-1-iwamatsu@nigauri.org Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use hash_for_each_safe for safe removal of hash entry.
Fixes: acfdd18591ea ("firmware: xilinx: Use hash-table for api feature check") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Tejas Patel <tejas.patel@xilinx.com> Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com> Link: https://lore.kernel.org/r/1612765883-22018-1-git-send-email-rajan.vaja@xilinx.com Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit d3cb25a12138 ("usb: gadget: udc: fix spin_lock in pch_udc")
obviously was not thought through and had made the situation even worse
than it was before. Two changes after almost reverted it. but a few
leftovers have been left as it. With this revert d3cb25a12138 completely.
While at it, narrow down the scope of unlocked section to prevent
potential race when prot_stall is assigned.
Patch is broken, it effectively makes qxl_drm_release() a nop
because on normal driver shutdown qxl_drm_release() is called
*after* drm_dev_unregister().
Fixes: b91907a62411 ("drm/qxl: do not run release if qxl failed to init") Cc: Tong Zhang <ztong0001@gmail.com> Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Acked-by: Thomas Zimmermann <tzimmermann@suse.de> Link: http://patchwork.freedesktop.org/patch/msgid/20210204145712.1531203-3-kraxel@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch complains about missing that the ovl_override_creds() doesn't
have a matching revert_creds() if the dentry is disconnected. Fix this
by moving the ovl_override_creds() until after the disconnected check.
Fixes: aa3ff3c152ff ("ovl: copy up of disconnected dentries") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In stmpe_devices_init(), the start and end field of these structs are
modified, so they can not be const. Add a comment to those structs that
lacked it to reduce the risk that this happens again.
Adding the destroy_workqueue call in i3c_master_register introduced below
kernel warning because it makes duplicate destroy_workqueue calls when
i3c_master_register fails after allocating the workqueue. The workqueue will
be destroyed by i3c_masterdev_release which is called by put_device at the
end of the i3c_master_register function eventually in failure cases so the
workqueue doesn't need to be destroyed in i3c_master_register.
This reverts commit 1b479fb80160
("drivers/net/wan/hdlc_fr: Fix a double free in pvc_xmit").
1. This commit is incorrect. "__skb_pad" will NOT free the skb on
failure when its "free_on_error" parameter is "false".
2. This commit claims to fix my commit. But it didn't CC me??
Fixes: 1b479fb80160 ("drivers/net/wan/hdlc_fr: Fix a double free in pvc_xmit") Cc: Lv Yunlong <lyl2019@mail.ustc.edu.cn> Signed-off-by: Xie He <xie.he.0141@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main thread could start to send SIG_IPI at any time, even before signal
blocked on vcpu thread. Therefore, start the vcpu thread with the signal
blocked.
Without this patch, on very busy cores the dirty_log_test could fail directly
on receiving a SIGUSR1 without a handler (when vcpu runs far slower than main).
Reported-by: Peter Xu <peterx@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a bug that can trigger with e.g. "taskset -c 0 ./dirty_log_test" or
when the testing host is very busy.
A similar previous attempt is done [1] but that is not enough, the reason is
stated in the reply [2].
As a summary (partly quotting from [2]):
The problem is I think one guest memory write operation (of this specific test)
contains a few micro-steps when page is during kvm dirty tracking (here I'm
only considering write-protect rather than pml but pml should be similar at
least when the log buffer is full):
(1) Guest read 'iteration' number into register, prepare to write, page fault
(2) Set dirty bit in either dirty bitmap or dirty ring
(3) Return to guest, data written
When we verify the data, we assumed that all these steps are "atomic", say,
when (1) happened for this page, we assume (2) & (3) must have happened. We
had some trick to workaround "un-atomicity" of above three steps, as previous
version of this patch wanted to fix atomicity of step (2)+(3) by explicitly
letting the main thread wait for at least one vmenter of vcpu thread, which
should work. However what I overlooked is probably that we still have race
when (1) and (2) can be interrupted.
One example calltrace when it could happen that we read an old interation, got
interrupted before even setting the dirty bit and flushing data:
It means iteration number cached in vcpu register can be very old when dirty
bit set and data flushed.
So far I don't see an easy way to guarantee all steps 1-3 atomicity but to sync
at the GUEST_SYNC() point of guest code when we do verification of the dirty
bits as what this patch does.
Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Sean Christopherson <seanjc@google.com> Cc: Andrew Jones <drjones@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20210417143602.215059-2-peterx@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The doc says:
"The characteristics of a specific redistributor region can
be read by presetting the index field in the attr data.
Only valid for KVM_DEV_TYPE_ARM_VGIC_V3"
Unfortunately the existing code fails to read the input attr data.
Fixes: 04c110932225 ("KVM: arm/arm64: Implement KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION") Cc: stable@vger.kernel.org#v4.17+ Signed-off-by: Eric Auger <eric.auger@redhat.com> Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210405163941.510258-3-eric.auger@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Abort the walk of coalesced MMIO zones if kvm_io_bus_unregister_dev()
fails to allocate memory for the new instance of the bus. If it can't
instantiate a new bus, unregister_dev() destroys all devices _except_ the
target device. But, it doesn't tell the caller that it obliterated the
bus and invoked the destructor for all devices that were on the bus. In
the coalesced MMIO case, this can result in a deleted list entry
dereference due to attempting to continue iterating on coalesced_zones
after future entries (in the walk) have been deleted.
Opportunistically add curly braces to the for-loop, which encompasses
many lines but sneaks by without braces due to the guts being a single
if statement.
Fixes: f65886606c2d ("KVM: fix memory leak in kvm_io_bus_unregister_dev()") Cc: stable@vger.kernel.org Reported-by: Hao Sun <sunhao.th@gmail.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If allocating a new instance of an I/O bus fails when unregistering a
device, wait to destroy the device until after all readers are guaranteed
to see the new null bus. Destroying devices before the bus is nullified
could lead to use-after-free since readers expect the devices on their
reference of the bus to remain valid.
Fixes: f65886606c2d ("KVM: fix memory leak in kvm_io_bus_unregister_dev()") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading the base address of the a REDIST region
through KVM_VGIC_V3_ADDR_TYPE_REDIST we expect the
redistributor region list to be populated with a single
element.
However list_first_entry() expects the list to be non empty.
Instead we should use list_first_entry_or_null which effectively
returns NULL if the list is empty.
Fixes: dbd9733ab674 ("KVM: arm/arm64: Replace the single rdist region by a list") Cc: <Stable@vger.kernel.org> # v4.18+ Signed-off-by: Eric Auger <eric.auger@redhat.com> Reported-by: Gavin Shan <gshan@redhat.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210412150034.29185-1-eric.auger@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop bits 63:32 of the base and/or index GPRs when calculating the
effective address of a VMX instruction memory operand. Outside of 64-bit
mode, memory encodings are strictly limited to E*X and below.
Fixes: 064aea774768 ("KVM: nVMX: Decoding memory operands of VMX instructions") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210422022128.3464144-7-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop bits 63:32 of the VMCS field encoding when checking for a nested
VM-Exit on VMREAD/VMWRITE in !64-bit mode. VMREAD and VMWRITE always
use 32-bit operands outside of 64-bit mode.
The actual emulation of VMREAD/VMWRITE does the right thing, this bug is
purely limited to incorrectly causing a nested VM-Exit if a GPR happens
to have bits 63:32 set outside of 64-bit mode.
Fixes: a7cde481b6e8 ("KVM: nVMX: Do not forward VMREAD/VMWRITE VMExits to L1 if required so by vmcs12 vmread/vmwrite bitmaps") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210422022128.3464144-6-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defer reloading the MMU after a EPTP successful EPTP switch. The VMFUNC
instruction itself is executed in the previous EPTP context, any side
effects, e.g. updating RIP, should occur in the old context. Practically
speaking, this bug is benign as VMX doesn't touch the MMU when skipping
an emulated instruction, nor does queuing a single-step #DB. No other
post-switch side effects exist.
Fixes: 41ab93727467 ("KVM: nVMX: Emulate EPTP switching for the L1 hypervisor") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210305011101.3597423-14-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reject KVM_SEV_INIT and KVM_SEV_ES_INIT if they are attempted after one
or more vCPUs have been created. KVM assumes a VM is tagged SEV/SEV-ES
prior to vCPU creation, e.g. init_vmcb() needs to mark the VMCB as SEV
enabled, and svm_create_vcpu() needs to allocate the VMSA. At best,
creating vCPUs before SEV/SEV-ES init will lead to unexpected errors
and/or behavior, and at worst it will crash the host, e.g.
sev_launch_update_vmsa() will dereference a null svm->vmsa pointer.
Fixes: 1654efcbc431 ("KVM: SVM: Add KVM_SEV_INIT command") Fixes: ad73109ae7ec ("KVM: SVM: Provide support to launch and run an SEV-ES guest") Cc: stable@vger.kernel.org Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210331031936.2495277-4-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set sev->es_active only after the guts of KVM_SEV_ES_INIT succeeds. If
the command fails, e.g. because SEV is already active or there are no
available ASIDs, then es_active will be left set even though the VM is
not fully SEV-ES capable.
Refactor the code so that "es_active" is passed on the stack instead of
being prematurely shoved into sev_info, both to avoid having to unwind
sev_info and so that it's more obvious what actually consumes es_active
in sev_guest_init() and its helpers.
Fixes: ad73109ae7ec ("KVM: SVM: Provide support to launch and run an SEV-ES guest") Cc: stable@vger.kernel.org Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210331031936.2495277-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the kvm_for_each_vcpu() helper to iterate over vCPUs when encrypting
VMSAs for SEV, which effectively switches to use online_vcpus instead of
created_vcpus. This fixes a possible null-pointer dereference as
created_vcpus does not guarantee a vCPU exists, since it is updated at
the very beginning of KVM_CREATE_VCPU. created_vcpus exists to allow the
bulk of vCPU creation to run in parallel, while still correctly
restricting the max number of max vCPUs.
Fixes: ad73109ae7ec ("KVM: SVM: Provide support to launch and run an SEV-ES guest") Cc: stable@vger.kernel.org Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210331031936.2495277-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Override the shadow root level in the MMU context when configuring
NPT for shadowing nested NPT. The level is always tied to the TDP level
of the host, not whatever level the guest happens to be using.
Fixes: 096586fda522 ("KVM: nSVM: Correctly set the shadow NPT root level in its MMU role") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210305011101.3597423-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the emulator's checks for illegal CR0, CR3, and CR4 values, as
the checks are redundant, outdated, and in the case of SEV's C-bit,
broken. The emulator manually calculates MAXPHYADDR from CPUID and
neglects to mask off the C-bit. For all other checks, kvm_set_cr*() are
a superset of the emulator checks, e.g. see CR4.LA57.
Fixes: a780a3ea6282 ("KVM: X86: Fix reserved bits check for MOV to CR3") Cc: Babu Moger <babu.moger@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210422022128.3464144-2-seanjc@google.com> Cc: stable@vger.kernel.org
[Unify check_cr_read and check_cr_write. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f1c6366e3043 ("KVM: SVM: Add required changes to support intercepts under
SEV-ES") prevents hypervisor accesses guest register state when the guest is
running under SEV-ES. The initial value of vcpu->arch.guest_state_protected
is false, it will not be updated in preemption notifiers after this commit which
means that the kernel spinlock lock holder will always be skipped to boost. Let's
fix it by always treating preempted is in the guest kernel mode, false positive
is better than skip completely.
Fixes: f1c6366e3043 (KVM: SVM: Add required changes to support intercepts under SEV-ES) Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1619080459-30032-1-git-send-email-wanpengli@tencent.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate the so called pae_root page on-demand, along with the lm_root
page, when shadowing 32-bit NPT with 64-bit NPT, i.e. when running a
32-bit L1. KVM currently only allocates the page when NPT is disabled,
or when L0 is 32-bit (using PAE paging).
Note, there is an existing memory leak involving the MMU roots, as KVM
fails to free the PAE roots on failure. This will be addressed in a
future commit.
Fixes: ee6268ba3a68 ("KVM: x86: Skip pae_root shadow allocation if tdp enabled") Fixes: b6b80c78af83 ("KVM: x86/mmu: Allocate PAE root array when using SVM's 32-bit NPT") Cc: stable@vger.kernel.org Reviewed-by: Ben Gardon <bgardon@google.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210305011101.3597423-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend kvm_s390_shadow_fault to return the pointer to the valid leaf
DAT table entry, or to the invalid entry.
Also return some flags in the lower bits of the address:
PEI_DAT_PROT: indicates that DAT protection applies because of the
protection bit in the segment (or, if EDAT, region) tables.
PEI_NOT_PTE: indicates that the address of the DAT table entry returned
does not refer to a PTE, but to a segment or region table.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Cc: stable@vger.kernel.org Reviewed-by: Janosch Frank <frankja@de.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Link: https://lore.kernel.org/r/20210302174443.514363-3-imbrenda@linux.ibm.com
[borntraeger@de.ibm.com: fold in a fix from Claudio] Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PoP documents:
134: The vector packed decimal facility is installed in the
z/Architecture architectural mode. When bit 134 is
one, bit 129 is also one.
135: The vector enhancements facility 1 is installed in
the z/Architecture architectural mode. When bit 135
is one, bit 129 is also one.
Looks like we confuse the vector enhancements facility 1 ("EXT") with the
Vector packed decimal facility ("BCD"). Let's fix the facility checks.
Detected while working on QEMU/tcg z14 support and only unlocking
the vector enhancements facility 1, but not the vector packed decimal
facility.
Fixes: 2583b848cad0 ("s390: report new vector facilities") Cc: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: David Hildenbrand <david@redhat.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Janosch Frank <frankja@linux.ibm.com> Link: https://lore.kernel.org/r/20210503121244.25232-1-david@redhat.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
store_regs_fmt2() has an ordering problem: first the guarded storage
facility is enabled on the local cpu, then preemption disabled, and
then the STGSC (store guarded storage controls) instruction is
executed.
If the process gets scheduled away between enabling the guarded
storage facility and before preemption is disabled, this might lead to
a special operation exception and therefore kernel crash as soon as
the process is scheduled back and the STGSC instruction is executed.
Fixes: 4e0b1ab72b8a ("KVM: s390: gs support for kvm guests") Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Janosch Frank <frankja@linux.ibm.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Cc: <stable@vger.kernel.org> # 4.12 Link: https://lore.kernel.org/r/20210415080127.1061275-1-hca@linux.ibm.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split kvm_s390_logical_to_effective to a generic function called
_kvm_s390_logical_to_effective. The new function takes a PSW and an address
and returns the address with the appropriate bits masked off. The old
function now calls the new function with the appropriate PSW from the vCPU.
This is needed to avoid code duplication for vSIE.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: stable@vger.kernel.org # for VSIE: correctly handle MVPG when in VSIE Link: https://lore.kernel.org/r/20210302174443.514363-2-imbrenda@linux.ibm.com Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HP Envy AiO 32-a12xxx has an external amp that is controlled via GPIO
bit 0x04. However, unlike other devices, this amp seems to shut down
itself after the certain period, hence the OS needs to up/down the bit
dynamically only during the actual playback.
This patch adds the control of the GPIO bit via the existing pcm_hook
mechanism. Ideally it should be triggered at the actual stream start,
but we have only the state change at prepare/cleanup, so use those for
switching the GPIO bit on/off. This should be good enough for the
purpose, and was actually confirmed to work fine.
In 9bbb94e57df1 ("ALSA: hda/realtek: fix static noise on ALC285 Lenovo
laptops") an existing Lenovo quirk was made more generic by removing a
0x12 pin requirement from the entry. This made the second chance table
Thinkpad jack entry unreachable as the pin configurations became
identical.
Revert the 0x12 pin requirement removal and move Thinkpad jack pin quirk
back to the primary pin table as they can co-exist when more specific
configurations come first.
Add a more targeted pin quirk for Lenovo devices that have 0x12 as
0x40000000.
The quirk entry for Uniwill ECS M31EI is with the PCI SSID device 0,
which means matching with all. That is, it's essentially equivalent
with SND_PCI_QUIRK_VENDOR(0x1584), which also matches with the
previous entry for Haier W18 applying the very same quirk.
Let's unify them with the single vendor-quirk entry.
Just re-order the alc662_fixup_tbl[] entries for Acer and ASUS devices
for avoiding the oversight of the duplicated or unapplied item in
future.
No functional changes.
Also Cc-to-stable for the further patch applications.
Just re-order the alc269_fixup_tbl[] entries for FSC, Medion, Samsung
and Lemote devices for avoiding the oversight of the duplicated or
unapplied item in future.
No functional changes.
Also Cc-to-stable for the further patch applications.
projects / thirdparty / kernel / stable.git / log
