Make sure the SONIC's DMA engine is idle before altering the transmit
and receive descriptors. Add a helper for this as it will be needed
again.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce839360f ("[PATCH] macsonic/jazzsonic network drivers update") Tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
NETDEV_TX_BUSY really should only be used by drivers that call
netif_tx_stop_queue() at the wrong moment. If dma_map_single() is
failed to map tx DMA buffer, it might trigger an infinite loop.
This patch use NETDEV_TX_OK instead of NETDEV_TX_BUSY, and change
printk to pr_err_ratelimited.
Fixes: d9fb9f384292 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers") Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21b1 ("slip: Fix deadlock in write_wakeup") Fixes: a8e83b17536a ("slcan: Port write_wakeup deadlock fix from slip") Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Tyler Hall <tylerwhall@gmail.com> Cc: linux-can@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: syzkaller@googlegroups.com Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
For SDHCIv3+ with programmable clock mode, minimal clock frequency is
still base clock / max(divider). Minimal programmable clock frequency is
always greater than minimal divided clock frequency. Without this patch,
SDHCI uses out-of-spec initial frequency when multiplier is big enough:
mmc1: mmc_rescan_try_freq: trying to init card at 468750 Hz
[for 480 MHz source clock divided by 1024]
The code in sdhci_calc_clk() already chooses a correct SDCLK clock mode.
Fixes: c3ed3877625f ("mmc: sdhci: add support for programmable clock mode") Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/ffb489519a446caffe7a0a05c4b9372bd52397bb.1579082031.git.mirq-linux@rere.qmqm.pl Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
WARNING: CPU: 0 PID: 0 at .../kernel/trace/ftrace.c:1979 ftrace_bug+0x1ad/0x230()
...
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.116-... #1
...
[<c0314e3d>] (unwind_backtrace) from [<c03115e9>] (show_stack+0x11/0x14)
[<c03115e9>] (show_stack) from [<c051a7f1>] (dump_stack+0x81/0xa8)
[<c051a7f1>] (dump_stack) from [<c0321c5d>] (warn_slowpath_common+0x69/0x90)
[<c0321c5d>] (warn_slowpath_common) from [<c0321cf3>] (warn_slowpath_null+0x17/0x1c)
[<c0321cf3>] (warn_slowpath_null) from [<c038ee9d>] (ftrace_bug+0x1ad/0x230)
[<c038ee9d>] (ftrace_bug) from [<c038f1f9>] (ftrace_process_locs+0x27d/0x444)
[<c038f1f9>] (ftrace_process_locs) from [<c08915bd>] (ftrace_init+0x91/0xe8)
[<c08915bd>] (ftrace_init) from [<c0885a67>] (start_kernel+0x34b/0x358)
[<c0885a67>] (start_kernel) from [<00308095>] (0x308095)
---[ end trace cb88537fdc8fa200 ]---
ftrace failed to modify [<c031266c>] prealloc_fixed_plts+0x8/0x60
actual: 44:f2:e1:36
ftrace record flags: 0
(0) expected tramp: c03143e9
Scenario 2, ARMv4T
==================
ftrace: allocating 14435 entries in 43 pages
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at kernel/trace/ftrace.c:2029 ftrace_bug+0x204/0x310
CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.5 #1
Hardware name: Cirrus Logic EDB9302 Evaluation Board
[<c0010a24>] (unwind_backtrace) from [<c000ecb0>] (show_stack+0x20/0x2c)
[<c000ecb0>] (show_stack) from [<c03c72e8>] (dump_stack+0x20/0x30)
[<c03c72e8>] (dump_stack) from [<c0021c18>] (__warn+0xdc/0x104)
[<c0021c18>] (__warn) from [<c0021d7c>] (warn_slowpath_null+0x4c/0x5c)
[<c0021d7c>] (warn_slowpath_null) from [<c0095360>] (ftrace_bug+0x204/0x310)
[<c0095360>] (ftrace_bug) from [<c04dabac>] (ftrace_init+0x3b4/0x4d4)
[<c04dabac>] (ftrace_init) from [<c04cef4c>] (start_kernel+0x20c/0x410)
[<c04cef4c>] (start_kernel) from [<00000000>] ( (null))
---[ end trace 0506a2f5dae6b341 ]---
ftrace failed to modify
[<c000c350>] perf_trace_sys_exit+0x5c/0xe8
actual: 1e:ff:2f:e1
Initializing ftrace call sites
ftrace record flags: 0
(0)
expected tramp: c000fb24
The analysis for this problem has been already performed previously,
refer to the link below.
Fix the above problems by allowing only selected reloc types in
__mcount_loc. The list itself comes from the legacy recordmcount.pl
script.
Link: https://lore.kernel.org/lkml/56961010.6000806@pengutronix.de/ Fixes: ed60453fa8f8 ("ARM: 6511/1: ftrace: add ARM support for C version of recordmcount") Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
reg2volt returns the voltage that matches a given register value.
Converting this back the other way with volt2reg didn't return the same
register value because it used truncation instead of rounding.
This meant that values read from sysfs could not be written back to sysfs
to set back the same register value.
With this change, volt2reg will return the same value for every voltage
previously returned by reg2volt (for the set of possible input values)
Check for NULL port data in the modem- and line-status handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe).
Note that the other (stubbed) event handlers qt2_process_xmit_empty()
and qt2_process_flush() would need similar sanity checks in case they
are ever implemented.
Fixes: f7a33e608d9a ("USB: serial: add quatech2 usb to serial driver") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Check for NULL port data in the control URB completion handlers to avoid
dereferencing a NULL pointer in the unlikely case where a port device
isn't bound to a driver (e.g. after an allocation failure on port
probe()).
Fixes: 0ca1268e109a ("USB Serial Keyspan: add support for USA-49WG & USA-28XG") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The driver receives the active port number from the device, but never
made sure that the port number was valid. This could lead to a
NULL-pointer dereference or memory corruption in case a device sends
data for an invalid port.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Check for NULL port data in the shared interrupt and bulk completion
callbacks to avoid dereferencing a NULL pointer in case a device sends
data for a port device which isn't bound to a driver (e.g. due to a
malicious device having unexpected endpoints or after an allocation
failure on port probe).
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Check for NULL port data in reset_resume() to avoid dereferencing a NULL
pointer in case the port device isn't bound to a driver (e.g. after a
failed control request at port probe).
Fixes: 1ded7ea47b88 ("USB: ch341 serial: fix port number changed after resume") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
USB-serial drivers must not be unbound from their ports before the
corresponding USB driver is unbound from the parent interface so
suppress the bind and unbind attributes.
Unbinding a serial driver while it's port is open is a sure way to
trigger a crash as any driver state is released on unbind while port
hangup is handled on the parent USB interface level. Drivers for
multiport devices where ports share a resource such as an interrupt
endpoint also generally cannot handle individual ports going away.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9ac9 ("[PATCH] USB: add driver for Keyspan Digital Remote") Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
I missed the fact that macvlan_broadcast() can be used both
in RX and TX.
skb_eth_hdr() makes only sense in TX paths, so we can not
use it blindly in macvlan_broadcast()
Fixes: 96cc4b69581d ("macvlan: do not assume mac_header is set in macvlan_broadcast()") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jurgen Van Ham <juvanham@gmail.com> Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Logical block size has type unsigned short. That means that it can be at
most 32768. However, there are architectures that can run with 64k pages
(for example arm64) and on these architectures, it may be possible to
create block devices with 64k block size.
For exmaple (run this on an architecture with 64k pages):
Mount will fail with this error because it tries to read the superblock using 2-sector
access:
device-mapper: writecache: I/O is not aligned, sector 2, size 1024, block size 65536
EXT4-fs (dm-0): unable to read superblock
This patch changes the logical block size from unsigned short to unsigned
int to avoid the overflow.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
gcc -O3 warns that some local variables are not properly initialized:
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_hang_notify':
drivers/scsi/fnic/vnic_dev.c:511:16: error: 'a0' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[0] = *a0;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:6: note: 'a0' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:691:10: note: 'a1' was declared here
u64 a0, a1;
^~
drivers/scsi/fnic/vnic_dev.c: In function 'fnic_dev_mac_addr':
drivers/scsi/fnic/vnic_dev.c:512:16: error: 'a1' is used uninitialized in this function [-Werror=uninitialized]
vdev->args[1] = *a1;
~~~~~~~~~~~~~~^~~~~
drivers/scsi/fnic/vnic_dev.c:698:10: note: 'a1' was declared here
u64 a0, a1;
^~
Apparently the code relies on the local variables occupying adjacent memory
locations in the same order, but this is of course not guaranteed.
Use an array of two u64 variables where needed to make it work correctly.
I suspect there is also an endianness bug here, but have not digged in deep
enough to be sure.
Fixes: 5df6d737dd4b ("[SCSI] fnic: Add new Cisco PCI-Express FCoE HBA") Fixes: mmtom ("init/Kconfig: enable -O3 for all arches") Link: https://lore.kernel.org/r/20200107201602.4096790-1-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
snd_seq_info_timer_read() reads the information of the timer assigned
for each queue, but it's done in a racy way which may lead to UAF as
spotted by syzkaller.
This patch applies the missing q->timer_mutex lock while accessing the
timer object as well as a slight code change to adapt the standard
coding style.
"Note that the microcode update must be aligned on a 16-byte boundary
and the size of the microcode update must be 1-KByte granular"
When early-load Intel microcode is loaded from initramfs, userspace tool
'iucode_tool' has already 16-byte aligned those microcode bits in that
initramfs image. Image that was created something like this:
However, when early-load Intel microcode is loaded from built-in
firmware BLOB using CONFIG_EXTRA_FIRMWARE= kernel config option, that
16-byte alignment is not guaranteed.
Fix this by forcing all built-in firmware BLOBs to 16-byte alignment.
[ If we end up having other firmware with much bigger alignment
requirements, we might need to introduce some method for the firmware
to specify it, this is the minimal "just increase the alignment a bit
to account for this one special case" patch - Linus ]
Signed-off-by: Jari Ruusu <jari.ruusu@gmail.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.16: adjust filename, context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
- D+ goes high, Host starts running by remote wakeup
- D+ is not stable, goes low
- Host requests GetPortStatus at (*1) and gets the following hub status:
- Current Connect Status bit is 0
- Connect Status Change bit is 1
- D+ stabilizes, goes high
- Host requests ClearPortFeature and thus Connect Status Change bit is
cleared at (*2)
- After waiting 100 ms, Host starts the Interrupt Transfer at (*3)
- Since the Connect Status Change bit is 0, Hub returns NAK.
In this case, port_event() is not called in hub_event() and Host cannot
recognize device. To solve this issue, flag change_bits even if only
Connect Status Change bit is 1 when got in the first GetPortStatus.
This issue occurs rarely because it only if D+ changes during a very
short time between GetPortStatus and ClearPortFeature. However, it is
fatal if it occurs in embedded system.
Signed-off-by: Keiya Nobuta <nobuta.keiya@fujitsu.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20200109051448.28150-1-nobuta.keiya@fujitsu.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Add missing endpoint sanity check to probe in order to prevent a
NULL-pointer dereference (or slab out-of-bounds access) when retrieving
the interrupt-endpoint bInterval on ndo_open() in case a device lacks
the expected endpoints.
Fixes: 40a82917b1d3 ("net/usb/r8152: enable interrupt transfer") Cc: hayeswang <hayeswang@realtek.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging
on open() or tiocmset() due to a malfunctioning (or malicious) device
until the device is physically disconnected.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 309a057932ab ("USB: opticon: add rts and cts support") Cc: Martin Jansen <martin.jansen@opticon.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The altsetting sanity check in set_sync_ep_implicit_fb_quirk() was
checking for there to be at least one altsetting but then went on to
access the second one, which may not exist.
This could lead to random slab data being used to initialise the sync
endpoint in snd_usb_add_endpoint().
Fixes: c75a8a7ae565 ("ALSA: snd-usb: add support for implicit feedback") Fixes: ca10a7ebdff1 ("ALSA: usb-audio: FT C400 sync playback EP to capture EP") Fixes: 5e35dc0338d8 ("ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204") Fixes: 17f08b0d9aaf ("ALSA: usb-audio: add implicit fb quirk for Axe-Fx II") Fixes: 103e9625647a ("ALSA: usb-audio: simplify set_sync_ep_implicit_fb_quirk") Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200114083953.1106-1-johan@kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The Axe-Fx II implicit feedback end point and the data sync endpoint
are in different interface descriptors. Add quirk to ensure a sync
endpoint is properly configured.
Signed-off-by: Alberto Aguirre <albaguirre@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An earlier commit (1b789577f655060d98d20e,
"netfilter: arp_tables: init netns pointer in xt_tgchk_param struct")
fixed missing net initialization for arptables, but turns out it was
incomplete. We can get a very similar struct net NULL deref during
error unwinding:
Also init the netns pointer in xt_tgdtor_param struct.
Fixes: add67461240c1d ("netfilter: add struct net * to target parameters") Reported-by: syzbot+91bdd8eece0f6629ec8b@syzkaller.appspotmail.com Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[bwh: Backported to 3.16:
- __arpt_unregister_table() has not been split out of
arpt_unregister_table()
- Add "net" parameter to arpt_unregister_table() and update its only
caller in arptable_filter.c] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
map->members is freed by ip_set_free() right before using it in
mtype_ext_cleanup() again. So we just have to move it down.
Reported-by: syzbot+4c3cc6dbe7259dbf9054@syzkaller.appspotmail.com Fixes: 40cd63bf33b2 ("netfilter: ipset: Support extensions which need a per data destroy function") Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Previous versions of `iio_compute_scan_bytes` only aligned each element
to its own length (i.e. its own natural alignment). Because multiple
consecutive sets of scan elements are buffered this does not work in
case the computed scan bytes do not align with the natural alignment of
the first scan element in the set.
This commit fixes this by aligning the scan bytes to the natural
alignment of the largest scan element in the set.
Fixes: 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by: Lars Möllendorf <lars.moellendorf@plating.de> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Some of ASUS laptops like UX431FL keyboard backlight cannot be set to
brightness 0. According to ASUS' information, the brightness should be
0x80 ~ 0x83. This patch fixes it by following the logic.
Fixes: e9809c0b9670 ("asus-wmi: add keyboard backlight support") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Reviewed-by: Daniel Drake <drake@endlessm.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 162f98dea487 ("Input: gtco - fix crash on detecting device without endpoints") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Vladis Dronov <vdronov@redhat.com> Link: https://lore.kernel.org/r/20191210113737.4016-5-johan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 8e20cf2bce12 ("Input: aiptek - fix crash on detecting device without endpoints") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Vladis Dronov <vdronov@redhat.com> Link: https://lore.kernel.org/r/20191210113737.4016-3-johan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
hidraw and uhid device nodes are always available for writing so we should
always report EPOLLOUT and EPOLLWRNORM bits, not only in the cases when
there is nothing to read.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org> Fixes: be54e7461ffdc ("HID: uhid: Fix returning EPOLLOUT from uhid_char_poll") Fixes: 9f3b61dc1dd7b ("HID: hidraw: Fix returning EPOLLOUT from hidraw_poll") Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[bwh: Backported to 3.16:
- Use unsigned int type instead of __poll_t
- s/EPOLL/POLL/g] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When polling a connected /dev/hidrawX device, it is useful to get the
EPOLLOUT when writing is possible. Since writing is possible as soon as
the device is connected, always return it.
Right now EPOLLOUT is only returned when there are also input reports
are available. This works if devices start sending reports when
connected, but some HID devices might need an output report first before
sending any input reports. This change will allow using EPOLLOUT here as
well.
Fixes: 378b80370aa1 ("hidraw: Return EPOLLOUT from hidraw_poll") Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[bwh: Backported to 3.16: s/EPOLL/POLL/g] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Always return EPOLLOUT from hidraw_poll when a device is connected.
This is safe since writes are always possible (but will always block).
hidraw does not support non-blocking writes and instead always calls
blocking backend functions on write requests. Hence, so far, a call to
poll never returned EPOLLOUT, which confuses tools like socat.
Signed-off-by: Fabian Henneke <fabian.henneke@gmail.com> In-reply-to: <CA+hv5qkyis03CgYTWeWX9cr0my-d2Oe+aZo+mjmWRXgjrGqyrw@mail.gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[bwh: Backported to 3.16: s/EPOLL/POLL/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Doing an add/remove/add on a SCSI device in an enclosure leads to an oops
caused by poisoned values in the enclosure device list pointers. The
reason is because we are keeping the enclosure device across the enclosed
device add/remove/add but the current code is doing a
device_add/device_del/device_add on it. This is the wrong thing to do in
sysfs, so fix it by not doing a device_del on the enclosure device simply
because of a hot remove of the drive in the slot.
[mkp: added missing email addresses]
Fixes: 43d8eb9cfd0a ("[SCSI] ses: add support for enclosure component hot removal") Link: https://lore.kernel.org/r/1578532892.3852.10.camel@HansenPartnership.com Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Reported-by: Luo Jiaxing <luojiaxing@huawei.com> Tested-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If an attached disk with protection information enabled is reformatted
to Type 0 the revalidation code does not clear the original protection
type and subsequent accesses will keep setting RDPROTECT/WRPROTECT.
Set the protection type to 0 if the disk reports PROT_EN=0 in READ
CAPACITY(16).
[mkp: commit desc]
Fixes: fe542396da73 ("[SCSI] sd: Ensure we correctly disable devices with unknown protection type") Link: https://lore.kernel.org/r/1578532344-101668-1-git-send-email-chenxiang66@hisilicon.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Currently, though the FDB entry is added to VF, it does not appear in
RAR filters. VF driver only allows to add 10 entries. Attempting to add
another causes an error. This patch removes limitation and allows use of
all free RAR entries for the FDB if needed.
Fixes: 46ec20ff7d ("ixgbevf: Add macvlan support in the set rx mode op") Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com> Acked-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Many drivers call skb_reset_mac_header() before using it,
but others do not.
Commit 6d1ccff62780 ("net: reset mac header in dev_start_xmit()")
attempted to fix this generically, but commit d346a3fae3ff
("packet: introduce PACKET_QDISC_BYPASS socket option") brought
back the macvlan bug.
Lets add a new helper, so that tx paths no longer have
to call skb_reset_mac_header() only to get a pointer
to skb->data.
Hopefully we will be able to revert 6d1ccff62780
("net: reset mac header in dev_start_xmit()") and save few cycles
in transmit fast path.
BUG: KASAN: use-after-free in __get_unaligned_cpu32 include/linux/unaligned/packed_struct.h:19 [inline]
BUG: KASAN: use-after-free in mc_hash drivers/net/macvlan.c:251 [inline]
BUG: KASAN: use-after-free in macvlan_broadcast+0x547/0x620 drivers/net/macvlan.c:277
Read of size 4 at addr ffff8880a4932401 by task syz-executor947/9579
Fixes: b863ceb7ddce ("[NET]: Add macvlan driver") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Let's limit TCA_FQ_QUANTUM to no more than 1 << 20 :
This max value should limit risks of breaking user setups
while fixing this bug.
Fixes: afe4fd062416 ("pkt_sched: fq: Fair Queue packet scheduler") Signed-off-by: Eric Dumazet <edumazet@google.com> Diagnosed-by: Florian Westphal <fw@strlen.de> Reported-by: syzbot+dc9071cc5a85950bdfce@syzkaller.appspotmail.com Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.16: Drop call to NL_SET_ERR_MSG_MOD() as extack is
not supported.] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Configuring fq with quantum 0 hangs the system, presumably because of a
non-interruptible infinite loop. Either way quantum 0 does not make sense.
Reproduce with:
sudo tc qdisc add dev lo root fq quantum 0 initial_quantum 0
ping 127.0.0.1
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba80 ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's") Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Both vlan_dev_change_flags() and vlan_dev_set_egress_priority()
can return an error. vlan_changelink() should not ignore them.
Fixes: 07b5b17e157b ("[VLAN]: Use rtnl_link API") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch is to fix a memleak caused by no place to free cmd->obj.chunk
for the unprocessed SCTP_CMD_REPLY. This issue occurs when failing to
process a cmd while there're still SCTP_CMD_REPLY cmds on the cmd seq
with an allocated chunk in cmd->obj.chunk.
So fix it by freeing cmd->obj.chunk for each SCTP_CMD_REPLY cmd left on
the cmd seq when any cmd returns error. While at it, also remove 'nomem'
label.
Reported-by: syzbot+107c4aff5f392bf1517f@syzkaller.appspotmail.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
'chrdev_open()' calls 'cdev_get()' to obtain a reference to the
'struct cdev *' stashed in the 'i_cdev' field of the target inode
structure. If the pointer is NULL, then it is initialised lazily by
looking up the kobject in the 'cdev_map' and so the whole procedure is
protected by the 'cdev_lock' spinlock to serialise initialisation of
the shared pointer.
Unfortunately, it is possible for the initialising thread to fail *after*
installing the new pointer, for example if the subsequent '->open()' call
on the file fails. In this case, 'cdev_put()' is called, the reference
count on the kobject is dropped and, if nobody else has taken a reference,
the release function is called which finally clears 'inode->i_cdev' from
'cdev_purge()' before potentially freeing the object. The problem here
is that a racing thread can happily take the 'cdev_lock' and see the
non-NULL pointer in the inode, which can result in a refcount increment
from zero and a warning:
Since 'cdev_get()' can already fail to obtain a reference, simply move
it over to use 'kobject_get_unless_zero()' instead of 'kobject_get()',
which will cause the racing thread to return -ENXIO if the initialising
thread fails unexpectedly.
Cc: Hillf Danton <hdanton@sina.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Reported-by: syzbot+82defefbbd8527e1c2cb@syzkaller.appspotmail.com Signed-off-by: Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20191219120203.32691-1-will@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
In the function, if register_trace_sched_migrate_task() returns error,
sched_switch/sched_wakeup_new/sched_wakeup won't unregister. That is
why fail_deprobe_sched_switch was added.
Link: http://lkml.kernel.org/r/20191231133530.2794-1-pilgrimtao@gmail.com Fixes: 478142c39c8c2 ("tracing: do not grab lock in wakeup latency function tracing") Signed-off-by: Kaitao Cheng <pilgrimtao@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The ftrace_profile->counter is unsigned long and
do_div truncates it to 32 bits, which means it can test
non-zero and be truncated to zero for division.
Fix this issue by using div64_ul() instead.
Link: http://lkml.kernel.org/r/20200103030248.14516-1-wenyang@linux.alibaba.com Fixes: e330b3bcd8319 ("tracing: Show sample std dev in function profiling") Fixes: 34886c8bc590f ("tracing: add average time in function to function profiler") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
On some archs with some configurations, MCOUNT_INSN_SIZE is not defined, and
this makes the stack tracer fail to compile. Just define it to zero in this
case.
Link: https://lore.kernel.org/r/202001020219.zvE3vsty%lkp@intel.com Fixes: 4df297129f622 ("tracing: Remove most or all of stack tracer stack size from stack_max_size") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter
tos value by RT_TOS() instead of using config tos directly.
vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't
return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS()
directly in function ip_tunnel_ecn_encap().
Fixes: 206aaafcd279 ("VXLAN: Use IP Tunnels tunnel ENC encap API") Fixes: 1400615d64cf ("vxlan: allow setting ipv6 traffic class") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When we receive a D-SACK, where the sequence number satisfies:
undo_marker <= start_seq < end_seq <= prior_snd_una
we consider this is a valid D-SACK and tcp_is_sackblock_valid()
returns true, then this D-SACK is discarded as "old stuff",
but the variable first_sack_index is not marked as negative
in tcp_sacktag_write_queue().
If this D-SACK also carries a SACK that needs to be processed
(for example, the previous SACK segment was lost), this SACK
will be treated as a D-SACK in the following processing of
tcp_sacktag_write_queue(), which will eventually lead to
incorrect updates of undo_retrans and reordering.
Fixes: fd6dad616d4f ("[TCP]: Earlier SACK block verification & simplify access to them") Signed-off-by: Pengcheng Yang <yangpc@wangsu.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan") Signed-off-by: Florian Faber <faber@faberman.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org> Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This device has a broken vendor-specific altsetting for interface 1,
where endpoint 0x85 is declared as an isochronous endpoint despite being
used by interface 2 for audio capture.
Since commit 3e4f8e21c4f2 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing, but in this case we need to ignore the first
instance in order to avoid breaking the audio capture interface.
Add a new device quirk that can be used to blacklist endpoints.
Since commit 3e4f8e21c4f2 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.
In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.
Tested-by: edes <edes@gmx.net> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Amend the endpoint-descriptor sanity checks to detect all duplicate
endpoint addresses in a configuration.
Commit 0a8fd1346254 ("USB: fix problems with duplicate endpoint
addresses") added a check for duplicate endpoint addresses within a
single alternate setting, but did not look for duplicate addresses in
other interfaces.
The current check would also not detect all duplicate addresses when one
endpoint is as a (bi-directional) control endpoint.
This specifically avoids overwriting the endpoint entries in struct
usb_device when enabling a duplicate endpoint, something which could
potentially lead to crashes or leaks, for example, when endpoints are
later disabled.
Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20191219161016.6695-1-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If the serial device is disconnected and reconnected, it re-enumerates
properly but does not link it. fwiw, linking means just saving the port
index, so allow it always as there is no harm in saving the same value
again even if it tries to relink with the same port.
Fixes: fb2b90014d78 ("tty: link tty and port before configuring it as console") Reported-by: Kenneth R. Crudup <kenny@panix.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Link: https://lore.kernel.org/r/20191227174434.12057-1-sudipm.mukherjee@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
An ino is unsigned, so display it as such in /proc/locks.
Signed-off-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Jeff Layton <jlayton@kernel.org>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Jia-Ju Bai reported a possible sleep-in-atomic scenario in the ice1724
driver with Infrasonic Quartet support code: namely, ice->set_rate
callback gets called inside ice->reg_lock spinlock, while the callback
in quartet.c holds ice->gpio_mutex.
This patch fixes the invalid call: it simply moves the calls of
ice->set_rate and ice->set_mclk callbacks outside the spinlock.
The EFI mixed mode entry code goes through the ordinary startup_32()
routine before jumping into the kernel's EFI boot code in 64-bit
mode. The 32-bit startup code must be entered with paging disabled,
but this is not documented as a requirement for the EFI handover
protocol, and so we should disable paging explicitly when entering
the kernel from 32-bit EFI firmware.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Cc: Arvind Sankar <nivedita@alum.mit.edu> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: https://lkml.kernel.org/r/20191224132909.102540-4-ardb@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When a PHY is probed, if the top bit is set, we end up requesting a
module with the string "mdio:-10101110000000100101000101010001" -
the top bit is printed to a signed -1 value. This leads to the module
not being loaded.
Fix the module format string and the macro generating the values for
it to ensure that we only print unsigned types and the top bit is
always 0/1. We correctly end up with
"mdio:10101110000000100101000101010001".
Fixes: 8626d3b43280 ("phylib: Support phy module autoloading") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
At least on the HP Envy x360 15-cp0xxx model the WMI interface
for HPWMI_FEATURE2_QUERY requires an outsize of at least 128 bytes,
otherwise it fails with an error code 5 (HPWMI_RET_INVALID_PARAMETERS):
Dec 06 00:59:38 kernel: hp_wmi: query 0xd returned error 0x5
We do not care about the contents of the buffer, we just want to know
if the HPWMI_FEATURE2_QUERY command is supported.
This commits bumps the buffer size, fixing the error.
Fixes: 8a1513b4932 ("hp-wmi: limit hotkey enable") BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1520703 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
BUG: KASAN: vmalloc-out-of-bounds in size_entry_mwt net/bridge/netfilter/ebtables.c:2063 [inline]
BUG: KASAN: vmalloc-out-of-bounds in compat_copy_entries+0x128b/0x1380 net/bridge/netfilter/ebtables.c:2155
Read of size 4 at addr ffffc900004461f4 by task syz-executor267/7937
Because padding isn't considered during computation of ->buf_user_offset,
"total" is decremented by fewer bytes than it should.
Therefore, the first part of
if (*total < sizeof(*entry) || entry->next_offset < sizeof(*entry))
will pass, -- it should not have. This causes oob access:
entry->next_offset is past the vmalloced size.
Reject padding and check that computed user offset (sum of ebt_entry
structure plus all individual matches/watchers/targets) is same
value that userspace gave us as the offset of the next entry.
XGMAC supports maximum MTU that can go to 16KB. Lets add this check in
the calculation of RX buffer size.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The 16KB RX Buffer must also be 16 byte aligned. Fix it.
Fixes: 7ac6653a085b ("stmmac: Move the STMicroelectronics driver") Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The host reports support for the synthetic feature X86_FEATURE_SSBD
when any of the three following hardware features are set:
CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31]
CPUID.80000008H:EBX.AMD_SSBD[bit 24]
CPUID.80000008H:EBX.VIRT_SSBD[bit 25]
Either of the first two hardware features implies the existence of the
IA32_SPEC_CTRL MSR, but CPUID.80000008H:EBX.VIRT_SSBD[bit 25] does
not. Therefore, CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31] should only be
set in the guest if CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31] or
CPUID.80000008H:EBX.AMD_SSBD[bit 24] is set on the host.
Fixes: 0c54914d0c52a ("KVM: x86: use Intel speculation bugs and features as derived in generic x86 code") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Jacob Xu <jacobhxu@google.com> Reviewed-by: Peter Shier <pshier@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Reported-by: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.16: adjust indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If a transaction error happens in vhci_recv_ret_submit(), event
handler closes connection and changes port status to kick hub_event.
Then hub tries to flush the endpoint URBs, but that causes infinite
loop between usb_hub_flush_endpoint() and vhci_urb_dequeue() because
"vhci_priv" in vhci_urb_dequeue() was already released by
vhci_recv_ret_submit() before a transmission error occurred. Thus,
vhci_urb_dequeue() terminates early and usb_hub_flush_endpoint()
continuously calls vhci_urb_dequeue().
The root cause of this issue is that vhci_recv_ret_submit()
terminates early without giving back URB when transaction error
occurs in vhci_recv_ret_submit(). That causes the error URB to still
be linked at endpoint list without “vhci_priv".
So, in the case of transaction error in vhci_recv_ret_submit(),
unlink URB from the endpoint, insert proper error code in
urb->status and give back URB.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Suwan Kim <suwan.kim027@gmail.com> Acked-by: Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20191213023055.19933-3-suwan.kim027@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16: adjust filename] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When disconnecting a USB hub that has some child device(s) connected to it
(such as a USB mouse), then the stack tries to clear halt and
reset device(s) which are _already_ physically disconnected.
The issue has been reproduced with:
CPU: IMX6D5EYM10AD or MCIMX6D5EYM10AE.
SW: U-Boot 2019.07 and kernel 4.19.40.
CPU: HP Proliant Microserver Gen8.
SW: Linux version 4.2.3-300.fc23.x86_64
In this situation there will be error bit for MMF active yet the
CERR equals EHCI_TUNE_CERR + halt. Existing implementation
interprets this as a stall [1] (chapter 8.4.5).
The possible conditions when the MMF will be active + halt
can be found from [2] (Table 4-13).
Fix for the issue is to check whether MMF is active and PID Code is
IN before checking for the stall. If these conditions are true then
it is not a stall.
What happens after the fix is that when disconnecting a hub with
attached device(s) the situation is not interpret as a stall.
There seems to be a race condition in tty drivers and I could see on
many boot cycles a NULL pointer dereference as tty_init_dev() tries to
do 'tty->port->itty = tty' even though tty->port is NULL.
'tty->port' will be set by the driver and if the driver has not yet done
it before we open the tty device we can get to this situation. By adding
some extra debug prints, I noticed that:
uart_add_one_port() registers the console, as soon as it registers, the
userspace tries to use it and that leads to tty_open() but
uart_add_one_port() has not yet done tty_port_link_device() and so
tty->port is not yet configured when control reaches tty_init_dev().
Further look into the code and tty_port_link_device() is done by
uart_add_one_port(). After registering the console uart_add_one_port()
will call tty_port_register_device_attr_serdev() and
tty_port_link_device() is called from this.
Call add tty_port_link_device() before uart_configure_port() is done and
add a check in tty_port_link_device() so that it only links the port if
it has not been done yet.
The current PCM code doesn't initialize explicitly the buffers
allocated for PCM streams, hence it might leak some uninitialized
kernel data or previous stream contents by mmapping or reading the
buffer before actually starting the stream.
Since this is a common problem, this patch simply adds the clearance
of the buffer data at hw_params callback. Although this does only
zero-clear no matter which format is used, which doesn't mean the
silence for some formats, but it should be OK because the intention is
just to clear the previous data on the buffer.
Backport of commit fdfc5c8594c2 ("tcp: remove empty skb from
write queue in error cases") in linux-4.14 stable triggered
various bugs. One of them has been fixed in commit ba2ddb43f270
("tcp: Don't dequeue SYN/FIN-segments from write-queue"), but
we still have crashes in some occasions.
Root-cause is that when tcp_sendmsg() has allocated a fresh
skb and could not append a fragment before being blocked
in sk_stream_wait_memory(), tcp_write_xmit() might be called
and decide to send this fresh and empty skb.
Sending an empty packet is not only silly, it might have caused
many issues we had in the past with tp->packets_out being
out of sync.
Fixes: c65f7f00c587 ("[TCP]: Simplify SKB data portion allocation with NETIF_F_SG.") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Christoph Paasch <cpaasch@apple.com> Acked-by: Neal Cardwell <ncardwell@google.com> Cc: Jason Baron <jbaron@akamai.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Before commit 0366a1c70b89 ("powerpc/irq: Run softirqs off the top of
the irq stack"), check_stack_overflow() was called by do_IRQ(), before
switching to the irq stack.
In that commit, do_IRQ() was renamed __do_irq(), and is now executing
on the irq stack, so check_stack_overflow() has just become almost
useless.
Move check_stack_overflow() call in do_IRQ() to do the check while
still on the current stack.
ext4_check_dir_entry() currently does not catch a case when a directory
entry ends so close to the block end that the header of the next
directory entry would not fit in the remaining space. This can lead to
directory iteration code trying to access address beyond end of current
buffer head leading to oops.
We now use btrfs_can_overcommit() to see if we can flip a block group
read only. Before this would fail because we weren't taking into
account the usable un-allocated space for allocating chunks. With my
patches we were allowed to do the balance, which is technically correct.
The test is trying to start balance on degraded mount. So now we're
trying to allocate a chunk and cannot because we want to allocate a
RAID1 chunk, but there's only 1 device that's available for usage. This
results in an ENOSPC.
But we shouldn't even be making it this far, we don't have enough
devices to restripe. The problem is we're using btrfs_num_devices(),
that also includes missing devices. That's not actually what we want, we
need to use rw_devices.
The chunk_mutex is not needed here, rw_devices changes only in device
add, remove or replace, all are excluded by EXCL_OP mechanism.
Fixes: e4d8ec0f65b9 ("Btrfs: implement online profile changing") Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ add stacktrace, update changelog, drop chunk_mutex ] Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
btrfs_del_root_ref() will simply WARN_ON() if the ref doesn't match in
any way, and then continue to delete the reference. This shouldn't
happen, we have these values because there's more to the reference than
the original root and the sub root. If any of these checks fail, return
-ENOENT.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Although it is safe to call this on already released paths with no locks
held or extent buffers, removing the redundant btrfs_release_path is
reasonable.
Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16 as dependency of commit d49d3287e74f
"btrfs: fix invalid removal of root ref"] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When starting writeback for a range that covers part of a preallocated
extent, due to a race with writeback for another range that also covers
another part of the same preallocated extent, we can end up in an infinite
loop.
Consider the following example where for inode 280 we have two dirty
ranges:
range A, from 294912 to 303103, 8192 bytes
range B, from 348160 to 438271, 90112 bytes
and we have the following file extent item layout for our inode:
leaf 38895616 gen 24544 total ptrs 29 free space 13820 owner 5
(...)
item 27 key (280 108 200704) itemoff 14598 itemsize 53
extent data disk bytenr 0 nr 0 type 1 (regular)
extent data offset 0 nr 94208 ram 94208
item 28 key (280 108 294912) itemoff 14545 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 2 (prealloc)
extent data offset 0 nr 81920 ram 81920
Then the following happens:
1) Writeback starts for range B (from 348160 to 438271), execution of
run_delalloc_nocow() starts;
2) The first iteration of run_delalloc_nocow()'s whil loop leaves us at
the extent item at slot 28, pointing to the prealloc extent item
covering the range from 294912 to 376831. This extent covers part of
our range;
3) An ordered extent is created against that extent, covering the file
range from 348160 to 376831 (28672 bytes);
4) We adjust 'cur_offset' to 376832 and move on to the next iteration of
the while loop;
5) The call to btrfs_lookup_file_extent() leaves us at the same leaf,
pointing to slot 29, 1 slot after the last item (the extent item
we processed in the previous iteration);
6) Because we are a slot beyond the last item, we call btrfs_next_leaf(),
which releases the search path before doing a another search for the
last key of the leaf (280 108 294912);
7) Right after btrfs_next_leaf() released the path, and before it did
another search for the last key of the leaf, writeback for the range
A (from 294912 to 303103) completes (it was previously started at
some point);
8) Upon completion of the ordered extent for range A, the prealloc extent
we previously found got split into two extent items, one covering the
range from 294912 to 303103 (8192 bytes), with a type of regular extent
(and no longer prealloc) and another covering the range from 303104 to
376831 (73728 bytes), with a type of prealloc and an offset of 8192
bytes. So our leaf now has the following layout:
leaf 38895616 gen 24544 total ptrs 31 free space 13664 owner 5
(...)
item 27 key (280 108 200704) itemoff 14598 itemsize 53
extent data disk bytenr 0 nr 0 type 1
extent data offset 0 nr 8192 ram 94208
item 28 key (280 108 208896) itemoff 14545 itemsize 53
extent data disk bytenr 10433142784 nr 86016 type 1
extent data offset 0 nr 86016 ram 86016
item 29 key (280 108 294912) itemoff 14492 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 1
extent data offset 0 nr 8192 ram 81920
item 30 key (280 108 303104) itemoff 14439 itemsize 53
extent data disk bytenr 10433052672 nr 81920 type 2
extent data offset 8192 nr 73728 ram 81920
9) After btrfs_next_leaf() returns, we have our path pointing to that same
leaf and at slot 30, since it has a key we didn't have before and it's
the first key greater then the key that was previously the last key of
the leaf (key (280 108 294912));
10) The extent item at slot 30 covers the range from 303104 to 376831
which is in our target range, so we process it, despite having already
created an ordered extent against this extent for the file range from
348160 to 376831. This is because we skip to the next extent item only
if its end is less than or equals to the start of our delalloc range,
and not less than or equals to the current offset ('cur_offset');
12) We then call create_io_em() for a 0 bytes range starting at offset
376832;
13) Then create_io_em() enters an infinite loop because its calls to
btrfs_drop_extent_cache() do nothing due to the 0 length range
passed to it. So no existing extent maps that cover the offset
376832 get removed, and therefore calls to add_extent_mapping()
return -EEXIST, resulting in an infinite loop. This loop from
create_io_em() is the following:
do {
btrfs_drop_extent_cache(BTRFS_I(inode), em->start,
em->start + em->len - 1, 0);
write_lock(&em_tree->lock);
ret = add_extent_mapping(em_tree, em, 1);
write_unlock(&em_tree->lock);
/*
* The caller has taken lock_extent(), who could race with us
* to add em?
*/
} while (ret == -EEXIST);
Also, each call to btrfs_drop_extent_cache() triggers a warning because
the start offset passed to it (376832) is smaller then the end offset
(376832 - 1) passed to it by -1, due to the 0 length:
Which results in flooding dmesg/syslog since btrfs_drop_extent_cache()
uses WARN_ON() and not WARN_ON_ONCE().
So fix this issue by changing run_delalloc_nocow()'s loop to move to the
next extent item when the current extent item ends at at offset less than
or equals to the current offset instead of the start offset.
Fixes: 80ff385665b7fc ("Btrfs: update nodatacow code v2") Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we fail to read the fs root corresponding with a reloc root we'll
just break out and free the reloc roots. But we remove our current
reloc_root from this list higher up, which means we'll leak this
reloc_root. Fix this by adding ourselves back to the reloc_roots list
so we are properly cleaned up.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
My fsstress modifications coupled with generic/475 uncovered a failure
to mount and replay the log if we hit a orphaned root. We do not want
to replay the log for an orphan root, but it's completely legitimate to
have an orphaned root with a log attached. Fix this by simply skipping
replaying the log. We still need to pin it's root node so that we do
not overwrite it while replaying other logs, as we re-read the log root
at every stage of the replay.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16:
- Pass fs_info->extent_root, instead of fs_info, as first argument to
btrfs_pin_extent_for_log_replay()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
If we get an -ENOENT back from btrfs_uuid_iter_rem when iterating the
uuid tree we'll just continue and do btrfs_next_item(). However we've
done a btrfs_release_path() at this point and no longer have a valid
path. So increment the key and go back and do a normal search.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We can just abort the transaction here, and in fact do that for every
other failure in this function except these two cases.
Reviewed-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16:
- Add root as second argument to btrfs_abort_transaction()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When a tree mod log user no longer needs to use the tree it calls
btrfs_put_tree_mod_seq() to remove itself from the list of users and
delete all no longer used elements of the tree's red black tree, which
should be all elements with a sequence number less then our equals to
the caller's sequence number. However the logic is broken because it
can delete and free elements from the red black tree that have a
sequence number greater then the caller's sequence number:
1) At a point in time we have sequence numbers 1, 2, 3 and 4 in the
tree mod log;
2) The task which got assigned the sequence number 1 calls
btrfs_put_tree_mod_seq();
3) Sequence number 1 is deleted from the list of sequence numbers;
4) The current minimum sequence number is computed to be the sequence
number 2;
5) A task using sequence number 2 is at tree_mod_log_rewind() and gets
a pointer to one of its elements from the red black tree through
a call to tree_mod_log_search();
6) The task with sequence number 1 iterates the red black tree of tree
modification elements and deletes (and frees) all elements with a
sequence number less then or equals to 2 (the computed minimum sequence
number) - it ends up only leaving elements with sequence numbers of 3
and 4;
7) The task with sequence number 2 now uses the pointer to its element,
already freed by the other task, at __tree_mod_log_rewind(), resulting
in a use-after-free issue. When CONFIG_DEBUG_PAGEALLOC=y it produces
a trace like the following:
Fix this by making btrfs_put_tree_mod_seq() skip deletion of elements that
have a sequence number equals to the computed minimum sequence number, and
not just elements with a sequence number greater then that minimum.
Fixes: bd989ba359f2ac ("Btrfs: add tree modification log functions") Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Testing with the new fsstress uncovered a pretty nasty deadlock with
lookup and snapshot deletion.
Process A
unlink
-> final iput
-> inode_tree_del
-> synchronize_srcu(subvol_srcu)
Process B
btrfs_lookup <- srcu_read_lock() acquired here
-> btrfs_iget
-> find inode that has I_FREEING set
-> __wait_on_freeing_inode()
We're holding the srcu_read_lock() while doing the iget in order to make
sure our fs root doesn't go away, and then we are waiting for the inode
to finish freeing. However because the free'ing process is doing a
synchronize_srcu() we deadlock.
Fix this by dropping the synchronize_srcu() in inode_tree_del(). We
don't need people to stop accessing the fs root at this point, we're
only adding our empty root to the dead roots list.
A larger much more invasive fix is forthcoming to address how we deal
with fs roots, but this fixes the immediate problem.
Fixes: 76dda93c6ae2 ("Btrfs: add snapshot/subvolume destroy ioctl") Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
[bwh: Backported to 3.16: No fs_info variable was used here] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
We should not be leaving half-mapped usages with potentially invalid
keycodes, as that may confuse hidinput_find_key() when the key is located
by index, which may end up feeding way too large keycode into the VT
keyboard handler and cause OOB write there:
BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
input_pass_values drivers/input/input.c:949 [inline]
input_set_keycode+0x290/0x320 drivers/input/input.c:954
evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
evdev_do_ioctl drivers/input/evdev.c:1150 [inline]
Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
However it is not above.
Hence, make do above remove sequence.
Fixes: fa417f7b520ee ("IB/mlx4: Add support for IBoE") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Link: https://lore.kernel.org/r/20191212091214.315005-3-leon@kernel.org Signed-off-by: Doug Ledford <dledford@redhat.com>
[bwh: Backported to 3.16: No need to call mlx4_ib_diag_cleanup()] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
When device is being removed (e.g during VPI port link type change
from ETH to IB), tasks for gid table changes should not be executed.
Flush the current queue of tasks and block further tasks from entering the queue.
Signed-off-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
As the commit 677fe555cbfb ("serial: imx: Fix recursive locking bug")
has mentioned the uart driver might cause recursive locking between
normal printing and the kernel debugging facilities (e.g. sysrq and
oops). In the commit it gave out suggestion for fixing recursive
locking issue: "The solution is to avoid locking in the sysrq case
and trylock in the oops_in_progress case."
This patch follows the suggestion (also used the exactly same code with
other serial drivers, e.g. amba-pl011.c) to fix the recursive locking
issue, this can avoid stuck caused by deadlock and print out log for
sysrq and oops.
Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Leo Yan <leo.yan@linaro.org> Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Link: https://lore.kernel.org/r/20191127141544.4277-2-leo.yan@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
The original ID that was added for Comet Lake PCH was
actually for the -LP (low power) variant even though the
constant for it said CMLH. Changing that while at it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Acked-by: Felipe Balbi <balbi@kernel.org> Link: https://lore.kernel.org/r/20191212093713.60614-1-heikki.krogerus@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[bwh: Backported to 3.16:
- No properties support
- Adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
This patch adds the necessary PCI ID for TGP-LP devices.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
[bwh: Backported to 3.16:
- No properties support
- Adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
projects / thirdparty / kernel / stable.git / log
