Commit 6c81fe7925cc4c42 ("arm64: enable context tracking") did not
update el0_sp_pc to use ct_user_exit, but this appears to have been
unintentional. In commit 6ab6463aeb5fbc75 ("arm64: adjust el0_sync so
that a function can be called") we made x0 available, and in the return
to userspace we call ct_user_enter in the kernel_exit macro.
Due to this, we currently don't correctly inform RCU of the user->kernel
transition, and may erroneously account for time spent in the kernel as
if we were in an extended quiescent state when CONFIG_CONTEXT_TRACKING
is enabled.
As we do record the kernel->user transition, a userspace application
making accesses from an unaligned stack pointer can demonstrate the
imbalance, provoking the following warning:
According to the PSCI specification and the SMC/HVC calling
convention, PSCI function_ids that are not implemented must
return NOT_SUPPORTED as return value.
Current KVM implementation takes an unhandled PSCI function_id
as an error and injects an undefined instruction into the guest
if PSCI implementation is called with a function_id that is not
handled by the resident PSCI version (ie it is not implemented),
which is not the behaviour expected by a guest when calling a
PSCI function_id that is not implemented.
This patch fixes this issue by returning NOT_SUPPORTED whenever
the kvm PSCI call is executed for a function_id that is not
implemented by the PSCI kvm layer.
Cc: <stable@vger.kernel.org> # 3.18+ Cc: Christoffer Dall <christoffer.dall@linaro.org> Acked-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.
Fixes: 36874c7e219 ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)
tpm_ibmvtpm_probe() calls ibmvtpm_reset_crq(ibmvtpm) without having yet
set the virtual device in the ibmvtpm structure. So in ibmvtpm_reset_crq,
the phype call contains empty unit addresses, ibmvtpm->vdev->unit_address.
Signed-off-by: Hon Ching(Vicky) Lo <honclo@linux.vnet.ibm.com> Signed-off-by: Joy Latten <jmlatten@linux.vnet.ibm.com> Reviewed-by: Ashley Lai <ashley@ahsleylai.com> Cc: <stable@vger.kernel.org> Fixes: 132f76294744 ("drivers/char/tpm: Add new device driver to support IBM vTPM") Signed-off-by: Peter Huewe <peterhuewe@gmx.de> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The way the mask is generated in regmap_field_init() is wrong.
Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift
overflow while calculating the mask field.
On some 32 bits architectures, such as x86, the generated mask is 0,
instead of the expected 0xffffffff.
This patch uses GENMASK() to fix the problem, as this macro is already safe
regarding shift overflow.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
This fixes a several year old regression that I found while trying
to get the Yoga 3 11 to work. The ideapad_rfk_set function is meant
to send a command to the embedded controller through ACPI, but
as of c1f73658ed, it sends the index of the rfkill device instead
of the command, and ignores the opcode field.
This changes it back to the original behavior, which indeed
flips the rfkill state as seen in the debugfs interface.
If updating journal superblock fails after journal data has been
flushed, the error is omitted and this will mislead the caller as a
normal case. In ocfs2, the checkpoint will be treated successfully
and the other node can get the lock to update. Since the sb_start is
still pointing to the old log block, it will rewrite the journal data
during journal recovery by the other node. Thus the new updates will
be overwritten and ocfs2 corrupts. So in above case we have to return
the error, and ocfs2_commit_cache will take care of the error and
prevent the other node to do update first. And only after recovering
journal it can do the new updates.
The issue discussion mail can be found at:
https://oss.oracle.com/pipermail/ocfs2-devel/2015-June/010856.html
http://comments.gmane.org/gmane.comp.file-systems.ext4/48841
[ Fixed bug in patch which allowed a non-negative error return from
jbd2_cleanup_journal_tail() to leak out of jbd2_fjournal_flush(); this
was causing xfstests ext4/306 to fail. -- Ted ]
In big endian mode regmap_bulk_read gives incorrect data
for byte reads.
This is because memcpy of a single byte from an address
after full word read gives different results when
endianness differs. ie. we get little-end in LE and big-end in BE.
Signed-off-by: Arun Chandran <achandran@mvista.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Fix the hbm power gating state machine so it will wait till it receives
confirmation interrupt for the PG_ISOLATION_EXIT message.
In process of the suspend flow the devices first have to exit from the
power gating state (runtime pm resume).
If we do not handle the confirmation interrupt after sending
PG_ISOLATION_EXIT message, we may receive it already after the suspend
flow has changed the device state and interrupt will be interpreted as a
spurious event, consequently link reset will be invoked which will
prevent the device from completing the suspend flow
kernel: [6603] mei_reset:136: mei_me 0000:00:16.0: powering down: end of reset
kernel: [476] mei_me_irq_thread_handler:643: mei_me 0000:00:16.0: function called after ISR to handle the interrupt processing.
kernel: mei_me 0000:00:16.0: FW not ready: resetting
Disable write buffering on the Toshiba ToPIC95 if it is enabled by
somebody (it is not supposed to be a power-on default according to
the datasheet). On the ToPIC95, practically no 32-bit Cardbus card
will work under heavy load without locking up the whole system if
this is left enabled. I tried about a dozen. It does not affect
16-bit cards. This is similar to the O2 bugs in early controller
revisions it seems.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55961 Cc: <stable@vger.kernel.org> Signed-off-by: Ryan C. Underwood <nemesis@icequake.net> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The commit cf108bca465d: "ext4: Invert the locking order of page_lock
and transaction start" caused __ext4_journalled_writepage() to drop
the page lock before the page was written back, as part of changing
the locking order to jbd2_journal_start -> page_lock. However, this
introduced a potential race if there was a truncate racing with the
data=journalled writeback mode.
Fix this by grabbing the page lock after starting the journal handle,
and then checking to see if page had gotten truncated out from under
us.
This fixes a number of different warnings or BUG_ON's when running
xfstests generic/086 in data=journalled mode, including:
After secondary CPU boot or hotplug, the active_mm of the idle thread is
&init_mm. The init_mm.pgd (swapper_pg_dir) is only meant for TTBR1_EL1
and must not be set in TTBR0_EL1. Since when active_mm == &init_mm the
TTBR0_EL1 is already set to the reserved value, there is no need to
perform any context reset.
the enum of "DAC Polarity" should be wm8960_enum[1].
Signed-off-by: Zidan Wang <zidan.wang@freescale.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
This patch fixes a bug in the XOR driver where the cleanup function can be
called and free descriptors that never been processed by the engine (which
result in data errors).
The cleanup function will free descriptors based on the ownership bit in
the descriptors.
For TX transactions, the TXCOMP bit in the Status Register is cleared
when the first data is written into the Transmit Holding Register.
In the lines from at91_do_twi_transfer():
at91_twi_write_data_dma(dev);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
the TXCOMP interrupt may be enabled before the DMA controller has
actually started to write into the THR. In such a case, the TXCOMP bit
is still set into the Status Register so the interrupt is triggered
immediately. The driver understands that a transaction completion has
occurred but this transaction hasn't started yet. Hence the TXCOMP
interrupt is no longer enabled by at91_do_twi_transfer() but instead
by at91_twi_write_data_dma_callback().
Also, the TXCOMP bit in the Status Register in not a clear on read flag
but a snapshot of the transmission state at the time the Status
Register is read.
When a NACK error is dectected by the I2C controller, the TXCOMP, NACK
and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP
interrupt is triggered at the same time. Also setting the TXRDY to 1
triggers the DMA controller to write the next data into the THR. Such
a write resets the TXCOMP bit to 0 in the SR. So depending on when the
interrupt handler reads the SR, it may fail to detect the NACK error
if it relies on the TXCOMP bit. The NACK bit and its interrupt should
be used instead.
For RX transactions, the TXCOMP bit in the Status Register is cleared
when the START bit is set into the Control Register. However to unify
the management of the TXCOMP bit when the DMA controller is used, the
TXCOMP interrupt is now enabled by the DMA callbacks for both TX and
RX transfers.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com> Cc: stable@vger.kernel.org #3.10 and later Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The pinctrl_gpio_range[] array described a first bank of 32 GPIOs and
a second one of 27 GPIOs. However, since there is a total of 60 MPP
pins that can be muxed as GPIOs, the second bank really has 28 GPIOs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: <stable@vger.kernel.org> # v3.15+ Fixes: ca6d9a084b56f ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The latest version of the Armada XP datasheet no longer documents the
VDD cpu_pd functions, which might indicate they are not working and/or
not supported. This commit ensures the pinctrl driver matches the
datasheet.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: <stable@vger.kernel.org> # v3.7+ Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
After updating to a more recent version of the Armada XP datasheet, we
realized that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: <stable@vger.kernel.org> # v3.7+ Fixes: 463e270f766a ("pinctrl: mvebu: add pinctrl driver for Armada XP") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
After updating to a more recent version of the Armada 375, we realized
that some of the pins documented as having a NAND-related
functionality in fact did not have such functionality. This commit
updates the pinctrl driver accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: <stable@vger.kernel.org> # v3.15+ Fixes: ce3ed59dcddd ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 375") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
A new revision of the Marvell Armada 38x hardware datasheet unveiled
that the definition of some of the PCIe functions were not
correct. This commit fixes the pinctrl driver accordingly.
Some PCIe functions simply do not exist, some of the PCIe functions in
fact were corresponding to other functions, and some PCIe functions
have been added.
Note: the seemingly unrelated removal of spi(cs2) on MPP47 is related:
this function is in fact implemented on MPP43, instead of a PCIe
function.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Cc: <stable@vger.kernel.org> # v3.15+ Fixes: ca6d9a084b56f ("pinctrl: mvebu: add pin-muxing driver for the Marvell Armada 380/385") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The Foxconn K8M890-8237A has two PCI host bridges, and we can't assign
resources correctly without the information from _CRS that tells us which
address ranges are claimed by which bridge. In the bugs mentioned below,
we incorrectly assign a sound card address (this example is from 1033299):
Add missing invocation of pm_generic_complete() to
acpi_subsys_complete() to allow ->complete callbacks provided
by the drivers of devices using the ACPI PM domain to be executed
during system resume.
Fixes: f25c0ae2b4c4 (ACPI / PM: Avoid resuming devices in ACPI PM domain during system suspend) Cc: 3.16+ <stable@vger.kernel.org> # 3.16+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The buffer for condtraints debug isn't big enough to hold the output
in all cases. So fix this issue by increasing the buffer.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The commit referenced below deferred waiting for command completion until
the start of the next command, allowing hardware to do the latching
asynchronously. Unfortunately, being ready to accept a new command is the
only indication we have that the previous command is completed. In cases
where we need that state change to be enabled, we must still wait for
completion. For instance, pciehp_reset_slot() attempts to disable anything
that might generate a surprise hotplug on slots that support presence
detection. If we don't wait for those settings to latch before the
secondary bus reset, we negate any value in attempting to prevent the
spurious hotplug.
Create a base function with optional wait and helper functions so that
pcie_write_cmd() turns back into the "safe" interface which waits before
and after issuing a command and add pcie_write_cmd_nowait(), which
eliminates the trailing wait for asynchronous completion. The following
functions are returned to their previous behavior:
The rationale is that pciehp_power_on_slot() enables the link and therefore
relies on completion of power-on. pciehp_power_off_slot() and
pcie_disable_notification() need a wait because data structures may be
freed after these calls and continued signaling from the device would be
unexpected. And, of course, pciehp_reset_slot() needs to wait for the
scenario outlined above.
Once the data is sent, we need to preserve the full frame for
the ndlc state machine. If the NDLC ACK is not received in time,
the ndlc layer will resend the same frame.
Having the header byte pulled will corrupt the frame.
Since ndev->driver_data is allocated by devm_kzalloc(), we do not
need the inappropriate kfree to free it in driver's remove function.
Freeing will trigger when driver unloads.
Cc: stable@vger.kernel.org Acked-by: Christophe Ricard <christophe-h.ricard@st.com> Signed-off-by: Firo Yang <firogm@gmail.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
AR93xx and newer needs to stop rx before tx to avoid getting the DMA
engine or MAC into a stuck state.
This should reduce/fix the occurence of "Failed to stop Tx DMA" logspam.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
If the function fails reference counter to the object is not decremented
causing leaks.
This is hard to spot as it happens only on very low memory situations.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
If objects are moved back from system memory to VRAM (and spice id
created again) memory is already initialized so we need to set flag
to not clear memory.
If you don't do it after a while using desktop many images turns to
black or transparents.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com> Cc: stable@vger.kernel.org Reviewed-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
SOC_DAPM_SINGLE("Playback AMP", ..) should not be under kcontrols. It
causes kernel crash (NULL pointer) when the mixers are listed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
If the card is not part of any card the tas_data->codec is NULL since it is
set only during snd_soc_codec_driver.probe, which is not yet called.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Since commit bafc9b754f75 ("vfs: More precise tests in d_invalidate"),
mounted subvolumes can be deleted because d_invalidate() won't fail.
However, we run into problems when we attempt to delete the default
subvolume while it is mounted as the root filesystem:
# btrfs subvol list /
ID 257 gen 306 top level 5 path rootvol
ID 267 gen 334 top level 5 path snap1
# btrfs subvol get-default /
ID 267 gen 334 top level 5 path snap1
# btrfs inspect-internal rootid /
267
# mount -o subvol=/ /dev/vda1 /mnt
# btrfs subvol del /mnt/snap1
Delete subvolume (no-commit): '/mnt/snap1'
ERROR: cannot delete '/mnt/snap1' - Operation not permitted
# findmnt /
findmnt: can't read /proc/mounts: No such file or directory
# ls /proc
#
Markus reported that this same scenario simply led to a kernel oops.
This happens because in btrfs_ioctl_snap_destroy(), we call
d_invalidate() before we check may_destroy_subvol(), which means that we
detach the submounts and drop the dentry before erroring out. Instead,
we should only invalidate the dentry once the deletion has succeeded.
Additionally, the shrink_dcache_sb() isn't necessary; d_invalidate()
will prune the dcache for the deleted subvolume.
Cc: <stable@vger.kernel.org> Fixes: bafc9b754f75 ("vfs: More precise tests in d_invalidate") Reported-by: Markus Schauler <mschauler@gmail.com> Signed-off-by: Omar Sandoval <osandov@osandov.com> Signed-off-by: Chris Mason <clm@fb.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Increase the default init stage change timeout from 15 seconds to 30 seconds.
This resolves issues we have seen with some adapters not transitioning
to the first init stage within 15 seconds, which results in adapter
initialization failures.
Cc: <stable@vger.kernel.org> Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The CrystalCove GPIO irqchip doesn't have irq_set_wake callback defined
so we should set IRQCHIP_SKIP_SET_WAKE for it or it would cause an irq
desc's wake_depth unbalanced warning during system resume phase from the
gpio_keys driver, which is the driver for the power button of the ASUS
T100 laptop.
When we take a PMU exception or a software event we call
perf_read_regs(). This overloads regs->result with a boolean that
describes if we should use the sampled instruction address register
(SIAR) or the regs.
If the exception is in kernel, we start with the kernel regs and
backtrace through the kernel stack. At this point we switch to the
userspace regs and backtrace the user stack with perf_callchain_user().
Unfortunately these regs have not got the perf_read_regs() treatment,
so regs->result could be anything. If it is non zero,
perf_instruction_pointer() decides to use the SIAR, and we get issues
like this:
Problem: When an operation like WRITE receives a BAD_STATEID, even though
recovery code clears the RECLAIM_NOGRACE recovery flag before recovering
the open state, because of clearing delegation state for the associated
inode, nfs_inode_find_state_and_recover() gets called and it makes the
same state with RECLAIM_NOGRACE flag again. As a results, when we restart
looking over the open states, we end up in the infinite loop instead of
breaking out in the next test of state flags.
Solution: unset the RECLAIM_NOGRACE set because of
calling of nfs_inode_find_state_and_recover() after returning from calling
recover_open() function.
Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset.
Dissolve the function hub_port_finish_reset() completely and divide the
actions to be taken into those which need to be done after each reset
attempt and those which need to be done after the full procedure is
complete, and place them in the appropriate places in hub_port_reset().
Also, remove an unneeded forward declaration of hub_port_reset().
Verbose Problem Description:
USB 3.0 devices may be "lost for good" during a hub port reset.
This makes Linux unable to boot from USB 3.0 devices in certain
constellations of host controllers and devices, because the USB device is
lost during initialization, preventing the rootfs from being mounted.
The underlying problem is that in the affected constellations, during the
processing inside hub_port_reset(), the hub link state goes from 0 to
SS.inactive after the initial reset, and back to 0 again only after the
following "warm" reset.
However, hub_port_finish_reset() is called after each reset attempt and
sets the state the connected USB device based on the "preliminary" status
of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when
the following warm reset is complete and hub_port_finish_reset() is
called again, its call to set the device to USB_STATE_DEFAULT is blocked
by usb_set_device_state() which does not allow taking USB devices out of
USB_STATE_NOTATTACHED state.
Thanks to Alan Stern for guiding me to the proper solution and how to
submit it.
With an RTL8191SU USB adaptor, sometimes the hints for a fragmented
packet are set, but the packet length is too large. Allocate enough
space to prevent memory corruption and a resulting kernel panic [1].
In case of non-Isochronous transfers, we don't
want to clear DWC3_EP_BUSY flag until XferComplete
event. That's because XferInProgress was only enabled
so we can recycle TRBs and usb_requests quicker, but
there are still other pending requests being transferred.
In order to make sure we don't allow for another StartTransfer
command while the HW is still processing other transfers,
we must keep DWC3_EP_BUSY flag set and this what this patch
does.
The Arizona codec drivers had an incorrect dB scaling for the
noise generator gain that started at 0dB and went upwards.
Actually the highest setting is 0dB.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
If, at the time __rcu_process_callbacks() is invoked, there are callbacks
in Tiny RCU's callback list, but none of them are ready to be invoked,
the current list-management code will knit the non-ready callbacks out
of the list. This can result in hangs and possibly worse. This commit
therefore inserts a check for there being no callbacks that can be
invoked immediately.
This bug is unlikely to occur -- you have to get a new callback between
the time rcu_sched_qs() or rcu_bh_qs() was called, but before we get to
__rcu_process_callbacks(). It was detected by the addition of RCU-bh
testing to rcutorture, which in turn was instigated by Iftekhar Ahmed's
mutation testing. Although this bug was made much more likely by 915e8a4fe45e (rcu: Remove fastpath from __rcu_process_callbacks()), this
did not cause the bug, but rather made it much more probable. That
said, it takes more than 40 hours of rcutorture testing, on average,
for this bug to appear, so this fix cannot be considered an emergency.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: <stable@vger.kernel.org> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Several of these drivers have there TX randomly blocked for 3~5 seconds while
measuring tx throughput (iperf). The root couse happens in rtl_pci_flush().
The function uses a while-loop to wait for TX queue length to decrease to 0.
The TX queue length counts the number of packets that are queued in the driver.
The driver relys on the TX OK interrupt to return skb and reduce TX queue length.
The interrupt subroutine disables interupts, reads the interrupt registers, and
then clears the registers in the beginning of _rtl_pci_interrupt(). After all
interupts process are finished, the driver invokes enable_interrupt() to enable
interupts. This behavior is normal for an interrupt subroutine.
But enable_interrupt() invokes clear_interrupt() again. This unexpected interrupt
clearing may cleari me fresh TX OK interrupts. These missing interrupts cause TX
queue length to never reduce to 0i, which causes rtl_pci_flush() to be stuck in
unterminated while-loop.
This patch removes clear_interrupt() in enable_interrupt() to avoid this behavior.
Signed-off-by: Vincent Fann <vincent_fann@realtek.com> Signed-off-by: Shao Fu <shaofu@realtek.com> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Stable <stable@vger.kernel.org> [3.18+] Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The commit df59fa7f4bca "spi: orion: support armada extended baud
rates" was too optimistic for the maximum baud rate that the Armada
SoCs can support. According to the hardware datasheet the maximum
frequency supported by the Armada 370 SoC is tclk/4. But for the
Armada XP, Armada 38x and Armada 39x SoCs the limitation is 50MHz and
for the Armada 375 it is tclk/15.
Currently the armada-370-spi compatible is only used by the Armada 370
and the Armada XP device tree. On Armada 370, tclk cannot be higher
than 200MHz. In order to be able to handle both SoCs, we can take the
minimum of 50MHz and tclk/4.
A proper solution is adding a compatible string for each SoC, but it
can't be done as a fix for compatibility reason (we can't modify
device tree that have been already released) and it will be part of a
separate patch.
Fixes: df59fa7f4bca (spi: orion: support armada extended baud rates) Reported-by: Kostya Porotchkin <kostap@marvell.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
A temperature conversion can take 750 ms and when possible the
w1_therm slave driver drops the bus_mutex to allow other bus
operations, but that includes operations such as a periodic slave
search, which can remove this slave when it is no longer detected.
If that happens the sl->family_data will be freed and set to NULL
causing w1_slave_show to crash when it wakes up.
HW has to be in known state before the initialisation
sequence is started. The polling step for settling aliveness
was set to 200ms while in practise this can be done in up to 30msecs.
Refine the mechanism introduced by commit f244d8b623da ("ACPIPHP / radeon /
nouveau: Fix VGA switcheroo problem related to hotplug") to propagate the
ignore_hotplug setting of the device to its parent bridge in case hotplug
notifications related to the graphics adapter switching are given for the
bridge rather than for the device itself (they need to be ignored in both
cases).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=61891 Link: https://bugs.freedesktop.org/show_bug.cgi?id=88927 Fixes: b440bde74f04 ("PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device") Reported-and-tested-by: tiagdtd-lava <tiagdtd-lava@yahoo.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: stable@vger.kernel.org # v3.17+ Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Clearly specify that "Cc: stable@vger.kernel.org" is strongly preferred so
that developers understand that the other options should only be used when
absolutely required.
Also specify how upstream commit ids should be referenced in patches
submitted directly to stable (I gathered this from looking at the stable
archives), and specify that any modified patches for stable should be
clearly documented in the patch description.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Signed-off-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The call to asymmetric_key_hex_to_key_id() from ca_keys_setup()
silently fails with -ENOMEM. Instead of dynamically allocating
memory from a __setup function, this patch defines a variable
and calls __asymmetric_key_hex_to_key_id(), a new helper function,
directly.
This bug was introduced by 'commit 46963b774d44 ("KEYS: Overhaul
key identification when searching for asymmetric keys")'.
Changelog:
- for clarification, rename hexlen to asciihexlen in
asymmetric_key_hex_to_key_id()
- add size argument to __asymmetric_key_hex_to_key_id() - David Howells
- inline __asymmetric_key_hex_to_key_id() - David Howells
- remove duplicate strlen() calls
Introduce the helper function srp_wait_for_queuecommand().
Move the definition of scsi_request_fn_active(). Add a comment
above srp_wait_for_queuecommand() that support for scsi-mq needs
to be added.
This patch does not change any functionality. A second call to
srp_wait_for_queuecommand() will be introduced in the next patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Cc: James Bottomley <JBottomley@Odin.com> Cc: Sagi Grimberg <sagig@mellanox.com> Cc: Sebastian Parschauer <sebastian.riemer@profitbricks.com> Cc: <stable@vger.kernel.org> #v3.13 Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
41f8bba7f555 ("of/pci: Add pci_register_io_range() and
pci_pio_to_address()") added support for systems with several I/O ranges
described by OF bindings. It modified pci_address_to_pio() look up the
io_range for a given CPU physical address, but the conversion was wrong.
WM8955_K_8_0_MASK bits is controlled by WM8955_PLL_CONTROL_3 rather than
WM8955_PLL_CONTROL_2.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Fix an oops during device initialization by correctly setting size_of_priv
instead of leaving it 0.
The regression was introduced by 8abe4a0a3f6d4217b16a ("[media] dib7000:
export just one symbol") and only fixed for one type of dib0700 based
devices in 9e334c75642b6e5bfb95 ("[media] Fix regression in some dib0700
based devices").
VMID Control 0 BIT[2:1] is VMID Divider Enable and Select
00 = VMID disabled (for OFF mode)
01 = 2 x 50kΩ divider (for normal operation)
10 = 2 x 250kΩ divider (for low power standby)
11 = 2 x 5kΩ divider (for fast start-up)
So WM8903_VMID_RES_250K should be 2 << 1, which is 4.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
WM8737_VMIDSEL_MASK is 0xC (VMIDSEL - [3:2]),
so it needs to left shift WM8737_VMIDSEL_SHIFT bits for setting these bits.
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
request_any_context_irq() returns a negative value on failure.
It returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED on success.
So fix testing return value of request_any_context_irq().
Also fixup the return value of devm_request_any_context_irq() to make it
consistent with request_any_context_irq().
Fixes: 0668d3065128 ("genirq: Add devm_request_any_context_irq()") Signed-off-by: Axel Lin <axel.lin@ingics.com> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1431334978.17783.4.camel@ingics.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The conversion to be16_add_cpu() is incorrect in case cryptlen is
negative due to premature (i.e. before addition / subtraction)
implicit conversion of cryptlen (int -> u16) leading to sign loss.
Setting a dev_pm_ops suspend/resume pair of callbacks but not a set of
hibernation callbacks means those pm functions will not be
called upon hibernation - that leads to system crash on ARM during
freezing if gpio-led is used in combination with CPU led trigger.
It may happen after freeze_noirq stage (GPIO is suspended)
and before syscore_suspend stage (CPU led trigger is suspended)
- usually when disable_nonboot_cpus() is called.
Log:
PM: noirq freeze of devices complete after 1.425 msecs
Disabling non-boot CPUs ...
^ system may crash or stuck here with message (TI AM572x)
WARNING: CPU: 0 PID: 3100 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x22c/0x370() 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in Supervisor mode during Functional access
CPU1: shutdown
^ or here
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation callbacks and move
led_suspend/led_resume under CONFIG_PM_SLEEP to avoid
build warnings.
Fixes: 73e1ab41a80d (leds: Convert led class driver from legacy pm ops to dev_pm_ops) Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Cc: 3.11+ <stable@vger.kernel.org> # 3.11+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Commit 007bea098b86 (intel_pstate: Add setting voltage value for
baytrail P states.) introduced byt_set_pstate() with the assumption that
it would always be run by the CPU whose MSR is to be written by it. It
turns out, however, that is not always the case in practice, so modify
byt_set_pstate() to enforce the MSR write done by it to always happen on
the right CPU.
Fixes: 007bea098b86 (intel_pstate: Add setting voltage value for baytrail P states.) Signed-off-by: Joe Konno <joe.konno@intel.com> Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com> Cc: 3.14+ <stable@vger.kernel.org> # 3.14+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Fixed by taking the mutex in blktrans_open and blktrans_release.
Note that this locking is already suggested in
include/linux/mtd/blktrans.h:
struct mtd_blktrans_ops {
...
/* Called with mtd_table_mutex held; no race with add/remove */
int (*open)(struct mtd_blktrans_dev *dev);
void (*release)(struct mtd_blktrans_dev *dev);
...
};
But we weren't following it.
Originally reported by (and patched by) Zhang and Giuseppe,
independently. Improved and rewritten.
Cc: stable@vger.kernel.org Reported-by: Zhang Xingcai <zhangxingcai@huawei.com> Reported-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Tested-by: Giuseppe Cantavenera <giuseppe.cantavenera.ext@nokia.com> Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Fix a race (with some kernel configurations) where a queued
master->pump_messages runs and frees dummy_tx/rx before
spi_unmap_msg is running (or is finished).
This results in the following messages:
BUG: Bad page state in process
page:db7ba030 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x200(arch_1)
page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
...
Reported-by: Noralf Trønnes <noralf@tronnes.org> Suggested-by: Noralf Trønnes <noralf@tronnes.org> Tested-by: Noralf Trønnes <noralf@tronnes.org> Signed-off-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Commit 7232398abc6a ("ARM: tegra: Convert PMC to a driver") changed tegra_resume()
location storing from late to early and, as a result, broke suspend on Tegra20.
PMC scratch register 41 is used by tegra LP1 resume code for retrieving stored
physical memory address of common resume function and in the same time used by
tegra20_cpu_shutdown() (shared by Tegra20 cpuidle driver and platform SMP code),
which is storing CPU1 "resettable" status. It implies strict order of scratch
register usage, otherwise resume function address is lost on Tegra20 after
disabling non-boot CPU's on suspend. Fix it by storing "resettable" status in
IRAM instead of PMC scratch register.
Events defined as watchpoints on nodes must have their config values
converted so that they apply to the respective node's XP. The
function setting new values was using wrong mask for the "port" field,
resulting in corrupted value. Fixed now.
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up much more values:
drivers/media/dvb-frontends/cx24116.c:983 cx24116_send_diseqc_msg() error: buffer overflow 'd->msg' 6 <= 23
The maximum size for a DiSEqC command is 6, according to the
userspace API. However, the code allows to write up to 7 values:
drivers/media/dvb-frontends/s5h1420.c:193 s5h1420_send_master_cmd() error: buffer overflow 'cmd->msg' 6 <= 7
When receiving a new iser connect request we serialize
the pending requests by adding the newly created iser connection
to the np accept list and let the login thread process the connect
request one by one (np_accept_wait).
In case we received a disconnect request before the iser_conn
has begun processing (still linked in np_accept_list) we should
detach it from the list and clean it up and not have the login
thread process a stale connection. We do it only when the connection
state is not already terminating (initiator driven disconnect) as
this might lead us to access np_accept_mutex after the np was released
in live shutdown scenarios.
Laptop with Turks/Thames GPU will freeze if dpm is enabled. It seems
the SMC engine is relying on some state inside the CP engine. CP needs
to chew at least one packet for it to get in good state for dynamic
power management.
This patch simply disabled and re-enable DPM after the ring test which
is enough to avoid the freeze.
Fixes: 6058bb362818 'ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller' Signed-off-by: Axel Lin <axel.lin@ingics.com> Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Carlo Caione <carlo@caione.org> Cc: Jason Cooper <jason@lakedaemon.net> Cc: stable@vger.kernel.org Link: http://lkml.kernel.org/r/1433684009.9134.1.camel@ingics.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
According to the Armada 38x datasheet, the window base address
registers value is set in bits [31:4] of the register and corresponds
to the transaction address bits [47:20].
Therefore, the 32bit base address value should be shifted right by
20bits and left by 4bits, resulting in 16 bit shift right.
The bug as not been noticed yet because if the memory available on
the platform is less than 2GB, then the base address is zero.
Until recently, mac80211 overwrote all the statistics it could
provide when getting called, but it now relies on the struct
having been zeroed by the caller. This was always the case in
nl80211, but wext used a static struct which could even cause
values from one device leak to another.
Using a static struct is OK (as even documented in a comment)
since the whole usage of this function and its return value is
always locked under RTNL. Not clearing the struct for calling
the driver has always been wrong though, since drivers were
free to only fill values they could report, so calling this
for one device and then for another would always have leaked
values from one to the other.
Fix this by initializing the structure in question before the
driver method call.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=99691
Cc: stable@vger.kernel.org Reported-by: Gerrit Renker <gerrit@erg.abdn.ac.uk> Reported-by: Alexander Kaltsas <alexkaltsas@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
This seems an use-after-free problem, and the root cause is
zone->wait_table was not set to *NULL* after free it in
try_offline_node.
When hot re-add a node, we will reuse the pgdat of it, so does the zone
struct, and when add pages to the target zone, it will init the zone
first (including the wait_table) if the zone is not initialized. The
judgement of zone initialized is based on zone->wait_table:
static inline bool zone_is_initialized(struct zone *zone)
{
return !!zone->wait_table;
}
so if we do not set the zone->wait_table to *NULL* after free it, the
memory hotplug routine will skip the init of new zone when hot re-add
the node, and the wait_table still points to the freed memory, then we
will access the invalid address when trying to wake up the waiting
people after the i/o operation with the page is done, such as mentioned
above.
The driver configures the IDLE condition to interrupt the SDMA engine.
Since the SDMA UART ROM script doesn't clear the IDLE bit itself, this
caused repeated 1-byte DMA transfers, regardless of available data in the
RX FIFO. Also, when returning due to the IDLE condition, the UART ROM
script already increased its counter, causing residue to be off by one.
This patch clears the IDLE condition to avoid repeated 1-byte DMA transfers
and decreases count by when the DMA transfer was aborted due to the IDLE
condition, fixing serial transfers using DMA on i.MX6Q.
Passive DP->DVI/HDMI dongles on DP++ ports show up to the system as HDMI
devices, as they do not have a sink device in them to respond to any AUX
traffic. When probing these dongles over the DDC, sometimes they will
NAK the first attempt even though the transaction is valid and they
support the DDC protocol. The retry loop inside of
drm_do_probe_ddc_edid() would normally catch this case and try the
transaction again, resulting in success.
drm: give up on edid retries when i2c bus is not responding
This added code to exit immediately if the return code from the
i2c_transfer function was -ENXIO in order to reduce the amount of time
spent in waiting for unresponsive or disconnected devices. That was
possible because the underlying i2c bit banging algorithm had retries of
its own (which, of course, were part of the reason for the bug the
commit fixes).
we've been flipping back and forth enabling the GMBUS transfers, but
we've settled since then. The GMBUS implementation does not do any
retries, however, bailing out of the drm_do_probe_ddc_edid() retry loop
on first encounter of -ENXIO. This, combined with Eugeni's commit, broke
the retry on -ENXIO.
Retry GMBUS once on -ENXIO on first message to mitigate the issues with
passive adapters.
This patch is based on the work, and commit message, by Todd Previte
<tprevite@gmail.com>.
According to the HSW b-spec we need to try clock divisors of 63
and 72, each 3 or more times, when attempting DP AUX channel
communication on a server chipset. This actually wasn't happening
due to a short-circuit that only checked the DP_AUX_CH_CTL_DONE bit
in status rather than checking that the operation was done and
that DP_AUX_CH_CTL_TIME_OUT_ERROR was not set.
[v2] Implemented alternate solution suggested by Jani Nikula.
Cc: stable@vger.kernel.org Signed-off-by: Jim Bride <jim.bride@linux.intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
The subtraction here was using a signed integer and did not have any
bounds checking at all. This commit adds proper bounds checking, made
easy by use of an unsigned integer. This way, a single packet won't be
able to remotely trigger a massive loop, locking up the system for a
considerable amount of time. A PoC follows below, which requires
ozprotocol.h from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
A network supplied parameter was not checked before division, leading to
a divide-by-zero. Since this happens in the softirq path, it leads to a
crash. A PoC follows below, which requires the ozprotocol.h file from
this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
Since elt->length is a u8, we can make this variable a u8. Then we can
do proper bounds checking more easily. Without this, a potentially
negative value is passed to the memcpy inside oz_hcd_get_desc_cnf,
resulting in a remotely exploitable heap overflow with network
supplied data.
This could result in remote code execution. A PoC which obtains DoS
follows below. It requires the ozprotocol.h file from this module.
static int hex2num(char c)
{
if (c >= '0' && c <= '9')
return c - '0';
if (c >= 'a' && c <= 'f')
return c - 'a' + 10;
if (c >= 'A' && c <= 'F')
return c - 'A' + 10;
return -1;
}
static int hwaddr_aton(const char *txt, uint8_t *addr)
{
int i;
for (i = 0; i < 6; i++) {
int a, b;
a = hex2num(*txt++);
if (a < 0)
return -1;
b = hex2num(*txt++);
if (b < 0)
return -1;
*addr++ = (a << 4) | b;
if (i < 5 && *txt++ != ':')
return -1;
}
return 0;
}
int main(int argc, char *argv[])
{
if (argc < 3) {
fprintf(stderr, "Usage: %s interface destination_mac\n", argv[0]);
return 1;
}
uint8_t dest_mac[6];
if (hwaddr_aton(argv[2], dest_mac)) {
fprintf(stderr, "Invalid mac address.\n");
return 1;
}
int sockfd = socket(AF_PACKET, SOCK_RAW, IPPROTO_RAW);
if (sockfd < 0) {
perror("socket");
return 1;
}
projects / thirdparty / kernel / stable.git / log
