In commit 16ad3f4022bb
("tipc: introduce variable window congestion control"), we applied
the algorithm to select window size from minimum window to the
configured maximum window for unicast link, and, besides we chose
to keep the window size for broadcast link unchanged and equal (i.e
fix window 50)
However, when setting maximum window variable via command, the window
variable was re-initialized to unexpect value (i.e 32).
We fix this by updating the fix window for broadcast as we stated.
Fixes: 16ad3f4022bb ("tipc: introduce variable window congestion control") Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The queue limit of the broadcast link is being calculated base on initial
MTU. However, when MTU value changed (e.g manual changing MTU on NIC
device, MTU negotiation etc.,) we do not re-calculate queue limit.
This gives throughput does not reflect with the change.
So fix it by calling the function to re-calculate queue limit of the
broadcast link.
Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race exists between closing a PCM and update of ELD data. In
hdmi_pcm_close(), hinfo->nid value is modified without taking
spec->pcm_lock. If this happens concurrently while processing an ELD
update in hdmi_pcm_setup_pin(), converter assignment may be done
incorrectly.
This bug was found by hitting a WARN_ON in snd_hda_spdif_ctls_assign()
in a HDMI receiver connection stress test:
In case HDA controller becomes active, but codec is runtime suspended,
jack detection is not successful and no interrupt is raised. This has
been observed with multiple Realtek codecs and HDA controllers from
different vendors. Bug does not occur if both codec and controller are
active, or both are in suspend. Bug can be easily hit on desktop systems
with no built-in speaker.
The problem can be fixed by powering up the codec once after every
controller runtime resume. Even if codec goes back to suspend later, the
jack detection will continue to work. Add a flag to 'hda_codec' to
describe codecs that require this flow from the controller driver.
Modify __azx_runtime_resume() to use pm_request_resume() to make the
intent clearer.
Mark all Realtek codecs with the new forced_resume flag.
When releasing a thread todo list when tearing down
a binder_proc, the following race was possible which
could result in a use-after-free:
1. Thread 1: enter binder_release_work from binder_thread_release
2. Thread 2: binder_update_ref_for_handle() -> binder_dec_node_ilocked()
3. Thread 2: dec nodeA --> 0 (will free node)
4. Thread 1: ACQ inner_proc_lock
5. Thread 2: block on inner_proc_lock
6. Thread 1: dequeue work (BINDER_WORK_NODE, part of nodeA)
7. Thread 1: REL inner_proc_lock
8. Thread 2: ACQ inner_proc_lock
9. Thread 2: todo list cleanup, but work was already dequeued
10. Thread 2: free node
11. Thread 2: REL inner_proc_lock
12. Thread 1: deref w->type (UAF)
The problem was that for a BINDER_WORK_NODE, the binder_work element
must not be accessed after releasing the inner_proc_lock while
processing the todo list elements since another thread might be
handling a deref on the node containing the binder_work element
leading to the node being freed.
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz> Proposed-by: Petr Tesarik <ptesarik@suse.cz> Tested-by: Petr Tesarik <ptesarik@suse.cz> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All TC actions call tcf_action_check_ctrlact() to validate
goto chain, so this check in tcf_action_init_1() is actually
redundant. Remove it to save troubles of leaking memory.
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com> Cc: Vinay Paradkar <vparadka@qti.qualcomm.com> Cc: Tyler Wear <twear@quicinc.com> Cc: David Ahern <dsahern@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes an uninit-value warning:
BUG: KMSAN: uninit-value in can_receive+0x26b/0x630 net/can/af_can.c:650
Reported-and-tested-by: syzbot+3f3837e61a48d32b495f@syzkaller.appspotmail.com Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Cc: Robin van der Gracht <robin@protonic.nl> Cc: Oleksij Rempel <linux@rempel-privat.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Link: https://lore.kernel.org/r/20201008061821.24663-1-xiyou.wangcong@gmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
removed the m_can_class_resume() call in the runtime resume path to get
rid of a infinite recursion, so the runtime resume now only handles the device
clocks.
Unfortunately it did not remove the complementary m_can_class_suspend() call in
the runtime suspend function, so those paths are now unbalanced, which causes
the pinctrl state to get stuck on the "sleep" state, which breaks all CAN
functionality on SoCs where this state is defined. Remove the
m_can_class_suspend() call to fix this.
Fixes: 0704c5743694 can: m_can_platform: remove unnecessary m_can_class_resume() call Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Link: https://lore.kernel.org/r/20200811081545.19921-1-l.stach@pengutronix.de Acked-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SOCK_TSTAMP_NEW (timespec64 instead of timespec) is also used for
hardware time stamps (configured via SO_TIMESTAMPING_NEW).
User space (ptp4l) first configures hardware time stamping via
SO_TIMESTAMPING_NEW which sets SOCK_TSTAMP_NEW. In the next step, ptp4l
disables SO_TIMESTAMPNS(_NEW) (software time stamps), but this must not
switch hardware time stamps back to "32 bit mode".
This problem happens on 32 bit platforms were the libc has already
switched to struct timespec64 (from SO_TIMExxx_OLD to SO_TIMExxx_NEW
socket options). ptp4l complains with "missing timestamp on transmitted
peer delay request" because the wrong format is received (and
discarded).
Fixes: 887feae36aee ("socket: Add SO_TIMESTAMP[NS]_NEW") Fixes: 783da70e8396 ("net: add sock_enable_timestamps") Signed-off-by: Christian Eggers <ceggers@arri.de> Acked-by: Willem de Bruijn <willemb@google.com> Acked-by: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comparison of optname with SO_TIMESTAMPING_NEW is wrong way around,
so SOCK_TSTAMP_NEW will first be set and than reset again. Additionally
move it out of the test for SOF_TIMESTAMPING_RX_SOFTWARE as this seems
unrelated.
This problem happens on 32 bit platforms were the libc has already
switched to struct timespec64 (from SO_TIMExxx_OLD to SO_TIMExxx_NEW
socket options). ptp4l complains with "missing timestamp on transmitted
peer delay request" because the wrong format is received (and
discarded).
Fixes: 9718475e6908 ("socket: Add SO_TIMESTAMPING_NEW") Signed-off-by: Christian Eggers <ceggers@arri.de> Reviewed-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Reviewed-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Acked-by: Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
skb_unshare() drops a reference count on the old skb unconditionally,
so in the failure case, we end up freeing the skb twice here.
And because the skb is allocated in fclone and cloned by caller
tipc_msg_reassemble(), the consequence is actually freeing the
original skb too, thus triggered the UAF by syzbot.
Fix this by replacing this skb_unshare() with skb_cloned()+skb_copy().
Fixes: ff48b6222e65 ("tipc: use skb_unshare() instead in tipc_buf_append()") Reported-and-tested-by: syzbot+e96a7ba46281824cc46a@syzkaller.appspotmail.com Cc: Jon Maloy <jmaloy@redhat.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At first when sendpage gets called, if there is more data, 'more' in
tls_push_data() gets set which later sets pending_open_record_frags, but
when there is no more data in file left, and last time tls_push_data()
gets called, pending_open_record_frags doesn't get reset. And later when
2 bytes of encrypted alert comes as sendmsg, it first checks for
pending_open_record_frags, and since this is set, it creates a record with
0 data bytes to encrypt, meaning record length is prepend_size + tag_size
only, which causes problem.
We should set/reset pending_open_record_frags based on more bit.
Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure") Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SMCD_DMBE_SIZES should include all valid DMBE buffer sizes, so the
correct value is 6 which means 1MB. With 7 the registration of an ISM
buffer would always fail because of the invalid size requested.
Fix that and set the value to 6.
Fixes: c6ba7c9ba43d ("net/smc: add base infrastructure for SMC-D and ISM") Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a delayed event is enqueued then the event worker will send this
event the next time it is running and no other flow is currently
active. The event handler is called for the delayed event, and the
pointer to the event keeps set in lgr->delayed_event. This pointer is
cleared later in the processing by smc_llc_flow_start().
This can lead to a use-after-free condition when the processing does not
reach smc_llc_flow_start(), but frees the event because of an error
situation. Then the delayed_event pointer is still set but the event is
freed.
Fix this by always clearing the delayed event pointer when the event is
provided to the event handler for processing, and remove the code to
clear it in smc_llc_flow_start().
The access of tcf_tunnel_info() produces the following splat, so fix it
by dereferencing the tcf_tunnel_key_params pointer with marker that
internal tcfa_liock is held.
=============================
WARNING: suspicious RCU usage
5.9.0+ #1 Not tainted
-----------------------------
include/net/tc_act/tc_tunnel_key.h:59 suspicious rcu_dereference_protected() usage!
other info that might help us debug this:
Fixes: 3ebaf6da0716 ("net: sched: Do not assume RTNL is held in tunnel key action helpers") Fixes: 7a47281439ba ("net: sched: lock action when translating it to flow_action infra") Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
using packetdrill it's possible to observe the same MPTCP DSN being acked
by different subflows with DACK4 and DACK8. This is in contrast with what
specified in RFC8684 §3.3.2: if an MPTCP endpoint transmits a 64-bit wide
DSN, it MUST be acknowledged with a 64-bit wide DACK. Fix 'use_64bit_ack'
variable to make it a property of MPTCP sockets, not TCP subflows.
Fixes: a0c1d0eafd1e ("mptcp: Use 32-bit DATA_ACK when possible") Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When processing a system suspend request we suspend modem endpoints
if they are enabled, and call ipa_cmd_tag_process() (which issues
IPA commands) to ensure the IPA pipeline is cleared. It is an error
to attempt to issue an IPA command before setup is complete, so this
is clearly a bug. But we also shouldn't suspend or resume any
endpoints that have not been set up.
Have ipa_endpoint_suspend() and ipa_endpoint_resume() immediately
return if setup hasn't completed, to avoid any attempt to configure
endpoints or issue IPA commands in that case.
Commit 4fc427e05158 ("ipv6_route_seq_next should increase position index")
tried to fix the issue where seq_file pos is not increased
if a NULL element is returned with seq_ops->next(). See bug
https://bugzilla.kernel.org/show_bug.cgi?id=206283
The commit effectively does:
- increase pos for all seq_ops->start()
- increase pos for all seq_ops->next()
For ipv6_route, increasing pos for all seq_ops->next() is correct.
But increasing pos for seq_ops->start() is not correct
since pos is used to determine how many items to skip during
seq_ops->start():
iter->skip = *pos;
seq_ops->start() just fetches the *current* pos item.
The item can be skipped only after seq_ops->show() which essentially
is the beginning of seq_ops->next().
In the above, I specify buffer size 4096, so all records can be returned
to user space with a single trip to the kernel.
If I use buffer size 128, since each record size is 149, internally
kernel seq_read() will read 149 into its internal buffer and return the data
to user space in two read() syscalls. Then user read() syscall will trigger
next seq_ops->start(). Since the current implementation increased pos even
for seq_ops->start(), it will skip record #2, #4 and #6, assuming the first
record is #1.
To fix the problem, create a fake pos pointer so seq_ops->start()
won't actually increase seq_file pos. With this fix, the
above `dd` command with `bs=128` will show correct result.
Fixes: 4fc427e05158 ("ipv6_route_seq_next should increase position index") Cc: Alexei Starovoitov <ast@kernel.org> Suggested-by: Vasily Averin <vvs@virtuozzo.com> Reviewed-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Yonghong Song <yhs@fb.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Acked-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04e3 ("net: fec: add phy_reset_after_clk_enable() support") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: David S. Miller <davem@davemloft.net> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04e3 ("net: fec: add phy_reset_after_clk_enable() support") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: David S. Miller <davem@davemloft.net> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: Richard Leitner <richard.leitner@skidata.com> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Between queuing the delayed work and finishing the setup of the dsa
ports, the process may sleep in request_module() (via
phy_device_create()) and the queued work may be executed prior to the
switch net devices being registered. In ksz_mib_read_work(), a NULL
dereference will happen within netof_carrier_ok(dp->slave).
Not queuing the delayed work in ksz_init_mib_timer() makes things even
worse because the work will now be queued for immediate execution
(instead of 2000 ms) in ksz_mac_link_down() via
dsa_port_link_register_of().
Call tree:
ksz9477_i2c_probe()
\--ksz9477_switch_register()
\--ksz_switch_register()
+--dsa_register_switch()
| \--dsa_switch_probe()
| \--dsa_tree_setup()
| \--dsa_tree_setup_switches()
| +--dsa_switch_setup()
| | +--ksz9477_setup()
| | | \--ksz_init_mib_timer()
| | | |--/* Start the timer 2 seconds later. */
| | | \--schedule_delayed_work(&dev->mib_read, msecs_to_jiffies(2000));
| | \--__mdiobus_register()
| | \--mdiobus_scan()
| | \--get_phy_device()
| | +--get_phy_id()
| | \--phy_device_create()
| | |--/* sleeping, ksz_mib_read_work() can be called meanwhile */
| | \--request_module()
| |
| \--dsa_port_setup()
| +--/* Called for non-CPU ports */
| +--dsa_slave_create()
| | +--/* Too late, ksz_mib_read_work() may be called beforehand */
| | \--port->slave = ...
| ...
| +--Called for CPU port */
| \--dsa_port_link_register_of()
| \--ksz_mac_link_down()
| +--/* mib_read must be initialized here */
| +--/* work is already scheduled, so it will be executed after 2000 ms */
| \--schedule_delayed_work(&dev->mib_read, 0);
\-- /* here port->slave is setup properly, scheduling the delayed work should be safe */
Solution:
1. Do not queue (only initialize) delayed work in ksz_init_mib_timer().
2. Only queue delayed work in ksz_mac_link_down() if init is completed.
3. Queue work once in ksz_switch_register(), after dsa_register_switch()
has completed.
Fixes: 7c6ff470aa86 ("net: dsa: microchip: add MIB counter reading support") Signed-off-by: Christian Eggers <ceggers@arri.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
netcons calls napi_poll with a budget of 0 to transmit packets.
Handle this by:
- skipping RX processing
- do not try to recycle TX packets to the RX cache
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tobias reported regressions in IPsec tests following the patch
referenced by the Fixes tag below. The root cause is dropping the
reset of the flowi4_oif after the fib_lookup. Apparently it is
needed for xfrm cases, so restore the oif update to ip_route_output_flow
right before the call to xfrm_lookup_route.
Fixes: 2fbc6e89b2f1 ("ipv4: Update exception handling for multipath routes via same device") Reported-by: Tobias Brunner <tobias@strongswan.org> Signed-off-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ingress large send packets are identified by either:
The IBMVETH_RXQ_LRG_PKT flag in the receive buffer
or with a -1 placed in the ip header checksum.
The method used depends on firmware version. Frame
geometry and sufficient header validation is performed by the
hypervisor eliminating the need for further header checks here.
Fixes: 7b5967389f5a ("ibmveth: set correct gso_size and gso_type") Signed-off-by: David Wilder <dwilder@us.ibm.com> Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com> Reviewed-by: Cristobal Forno <cris.forno@ibm.com> Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ibmveth_rx_csum_helper() must be called after ibmveth_rx_mss_helper()
as ibmveth_rx_csum_helper() may alter ip and tcp checksum values.
Fixes: 66aa0678efc2 ("ibmveth: Support to enable LSO/CSO for Trunk VEA.") Signed-off-by: David Wilder <dwilder@us.ibm.com> Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com> Reviewed-by: Cristobal Forno <cris.forno@ibm.com> Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 4-tuple NAT offload via PEDIT always overwrites all the 4-tuple
fields even if they had not been explicitly enabled. If any fields in
the 4-tuple are not enabled, then the hardware overwrites the
disabled fields with zeros, instead of ignoring them.
So, add a parser that can translate the enabled 4-tuple PEDIT fields
to one of the NAT mode combinations supported by the hardware and
hence avoid overwriting disabled fields to 0. Any rule with
unsupported NAT mode combination is rejected.
With suitably crafted reiserfs image and mount command reiserfs will
crash when trying to verify that XATTR_ROOT directory can be looked up
in / as that recurses back to xattr code like:
reiserfs_read_locked_inode() didn't initialize key length properly. Use
_make_cpu_key() macro for key initialization so that all key member are
properly initialized.
CC: stable@vger.kernel.org Reported-by: syzbot+d94d02749498bb7bab4b@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There exist many FT2232-based JTAG+UART adapter designs in which
FT2232 Channel A is used for JTAG and Channel B is used for UART.
The best way to handle them in Linux is to have the ftdi_sio driver
create a ttyUSB device only for Channel B and not for Channel A:
a ttyUSB device for Channel A would be bogus and will disappear as
soon as the user runs OpenOCD or other applications that access
Channel A for JTAG from userspace, causing undesirable noise for
users. The ftdi_sio driver already has a dedicated quirk for such
JTAG+UART FT2232 adapters, and it requires assigning custom USB IDs
to such adapters and adding these IDs to the driver with the
ftdi_jtag_quirk applied.
Boutique hardware manufacturer Falconia Partners LLC has created a
couple of JTAG+UART adapter designs (one buffered, one unbuffered)
as part of FreeCalypso project, and this hardware is specifically made
to be used with Linux hosts, with the intent that Channel A will be
accessed only from userspace via appropriate applications, and that
Channel B will be supported by the ftdi_sio kernel driver, presenting
a standard ttyUSB device to userspace. Toward this end the hardware
manufacturer will be programming FT2232 EEPROMs with custom USB IDs,
specifically with the intent that these IDs will be recognized by
the ftdi_sio driver with the ftdi_jtag_quirk applied.
Signed-off-by: Mychaela N. Falconia <falcon@freecalypso.org>
[johan: insert in PID order and drop unused define] Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While finding usb endpoints in vmk80xx_find_usb_endpoints(), check if
wMaxPacketSize = 0 for the endpoints found.
Some devices have isochronous endpoints that have wMaxPacketSize = 0
(as required by the USB-2 spec).
However, since this doesn't apply here, wMaxPacketSize = 0 can be
considered to be invalid.
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 3, Part C page 1319:
'128-bit equivalent strength for link and encryption keys
required using FIPS approved algorithms (E0 not allowed,
SAFER+ not allowed, and P-192 not allowed; encryption key
not shortened'
Only sockets will have the chan->data set to an actual sk, channels
like A2MP would have its own data which would likely cause a crash when
calling sk_filter, in order to fix this a new callback has been
introduced so channels can implement their own filtering if necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -EINVAL for authenc(hmac(sha1),cbc(aes)),
authenc(hmac(sha256),cbc(aes)) and authenc(hmac(sha512),cbc(aes))
if the cipher length is not multiple of the AES block.
This is to prevent an undefined device behaviour.
The setkey function for GCM/CCM algorithms didn't verify the key
length before copying the key and subtracting the salt length.
This patch delays the copying of the key til after the verification
has been done. It also adds checks on the key length to ensure
that it's at least as long as the salt.
syzbot is able to trigger a failure case inside the loop in
tcf_action_init(), and when this happens we clean up with
tcf_action_destroy(). But, as these actions are already inserted
into the global IDR, other parallel process could free them
before tcf_action_destroy(), then we will trigger a use-after-free.
Fix this by deferring the insertions even later, after the loop,
and committing all the insertions in a separate loop, so we will
never fail in the middle of the insertions any more.
One side effect is that the window between alloction and final
insertion becomes larger, now it is more likely that the loop in
tcf_del_walker() sees the placeholder -EBUSY pointer. So we have
to check for error pointer in tcf_del_walker().
Reported-and-tested-by: syzbot+2287853d392e4b42374a@syzkaller.appspotmail.com Fixes: 0190c1d452a9 ("net: sched: atomically check-allocate action") Cc: Vlad Buslov <vladbu@mellanox.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All TC actions call tcf_idr_insert() for new action at the end
of their ->init(), so we can actually move it to a central place
in tcf_action_init_1().
And once the action is inserted into the global IDR, other parallel
process could free it immediately as its refcnt is still 1, so we can
not fail after this, we need to move it after the goto action
validation to avoid handling the failure case after insertion.
This is found during code review, is not directly triggered by syzbot.
And this prepares for the next patch.
Cc: Vlad Buslov <vladbu@mellanox.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rcu read locks are needed to avoid potential race condition while
dereferencing radix tree from multiple threads. The issue was identified
by syzbot. Below is the crash report:
Fixes: 0c2204a4ad71 ("net: qrtr: Migrate nameservice to kernel from userspace") Reported-and-tested-by: syzbot+0f84f6eed90503da72fc@syzkaller.appspotmail.com Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When get_registers() fails in set_ethernet_addr(),the uninitialized
value of node_id gets copied over as the address.
So, check the return value of get_registers().
If get_registers() executed successfully (i.e., it returns
sizeof(node_id)), copy over the MAC address using ether_addr_copy()
(instead of using memcpy()).
Else, if get_registers() failed instead, a randomly generated MAC
address is set as the MAC address instead.
Reported-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com Tested-by: syzbot+abbc768b560c84d92fd3@syzkaller.appspotmail.com Acked-by: Petko Manolov <petkan@nucleusys.com> Signed-off-by: Anant Thazhemadam <anant.thazhemadam@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty TIOCL_SETSEL ioctl allocates a memory buffer big enough for text
selection area. The maximum allowed console size is
VC_RESIZE_MAXCOL * VC_RESIZE_MAXROW == 32767*32767 == ~1GB and typical
MAX_ORDER is set to allow allocations lot less than than (circa 16MB).
So it is quite possible to trigger huge allocation (and syzkaller just
did that) which is going to fail (which is fine) with a backtrace in
mm/page_alloc.c at WARN_ON_ONCE(!(gfp_mask & __GFP_NOWARN)) and
this may trigger panic (if panic_on_warn is enabled) and
leak kernel addresses to dmesg.
This passes __GFP_NOWARN to kmalloc_array to avoid unnecessary user-
triggered WARN_ON. Note that the error is not ignored and
the warning is still printed.
Declare GRE offload support with respect to the inner protocol. Add a
list of supported inner protocols on which the driver can offload
checksum and GSO. For other protocols, inform the stack to do the needed
operations. There is no noticeable impact on GRE performance.
Fixes: 2729984149e6 ("net/mlx5e: Support TSO and TX checksum offloads for GRE tunnels") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tls_sw_release_resources_tx() waits for encrypt_pending, which
can have race, so we need similar changes as in commit 0cada33241d9de205522e3858b18e506ca5cce2c here as well.
Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance") Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a user-space software manages fdb entries externally it should
set the ext_learn flag which marks the fdb entry as externally managed
and avoids expiring it (they're treated as static fdbs). Unfortunately
on events where fdb entries are flushed (STP down, netlink fdb flush
etc) these fdbs are also deleted automatically by the bridge. That in turn
causes trouble for the managing user-space software (e.g. in MLAG setups
we lose remote fdb entries on port flaps).
These entries are completely externally managed so we should avoid
automatically deleting them, the only exception are offloaded entries
(i.e. BR_FDB_ADDED_BY_EXT_LEARN + BR_FDB_OFFLOADED). They are flushed as
before.
Fixes: eb100e0e24a2 ("net: bridge: allow to add externally learned entries from user-space") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Openvswitch allows to drop a packet's Ethernet header, therefore
skb_mpls_push() and skb_mpls_pop() might be called with ethernet=true
and mac_len=0. In that case the pointer passed to skb_mod_eth_type()
doesn't point to an Ethernet header and the new Ethertype is written at
unexpected locations.
Fix this by verifying that mac_len is big enough to contain an Ethernet
header.
Fixes: fa4e0f8855fc ("net/sched: fix corrupted L2 header with MPLS 'push' and 'pop' actions") Signed-off-by: Guillaume Nault <gnault@redhat.com> Acked-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If userspace doesn't complete the policy dump, we leak the
allocated state. Fix this.
Fixes: d07dcf9aadd6 ("netlink: add infrastructure to expose policies to userspace") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We got reports from GKE customers flows being reset by netfilter
conntrack unless nf_conntrack_tcp_be_liberal is set to 1.
Traces seemed to suggest ACK packet being dropped by the
packet capture, or more likely that ACK were received in the
wrong order.
wscale=7, SYN and SYNACK not shown here.
This ACK allows the sender to send 1871*128 bytes from seq 51359321 :
New right edge of the window -> 51359321+1871*128=51598809
09:17:23.389210 IP A > B: Flags [.], ack 51359321, win 1871, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389212 IP B > A: Flags [.], seq 51422681:51424089, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 1408
09:17:23.389214 IP A > B: Flags [.], ack 51422681, win 1376, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389253 IP B > A: Flags [.], seq 51424089:51488857, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 64768
09:17:23.389272 IP A > B: Flags [.], ack 51488857, win 859, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389275 IP B > A: Flags [.], seq 51488857:51521241, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384
Receiver now allows to send 606*128=77568 from seq 51521241 :
New right edge of the window -> 51521241+606*128=51598809
09:17:23.389296 IP A > B: Flags [.], ack 51521241, win 606, options [nop,nop,TS val 10 ecr 999], length 0
09:17:23.389308 IP B > A: Flags [.], seq 51521241:51553625, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 32384
It seems the sender exceeds RWIN allowance, since 51611353 > 51598809
09:17:23.389346 IP B > A: Flags [.], seq 51553625:51611353, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 57728
09:17:23.389356 IP B > A: Flags [.], seq 51611353:51618393, ack 1577, win 268, options [nop,nop,TS val 999 ecr 10], length 7040
09:17:23.389367 IP A > B: Flags [.], ack 51611353, win 0, options [nop,nop,TS val 10 ecr 999], length 0
netfilter conntrack is not happy and sends RST
09:17:23.389389 IP A > B: Flags [R], seq 92176528, win 0, length 0
09:17:23.389488 IP B > A: Flags [R], seq 174478967, win 0, length 0
Now imagine ACK were delivered out of order and tcp_add_backlog() sets window based on wrong packet.
New right edge of the window -> 51521241+859*128=51631193
Normally TCP stack handles OOO packets just fine, but it
turns out tcp_add_backlog() does not. It can update the window
field of the aggregated packet even if the ACK sequence
of the last received packet is too old.
Many thanks to Alexandre Ferrieux for independently reporting the issue
and suggesting a fix.
Fixes: 4f693b55c3d2 ("tcp: implement coalescing on backlog queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Alexandre Ferrieux <alexandre.ferrieux@orange.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When memory is hotplug added or removed the min_free_kbytes should be
recalculated based on what is expected by khugepaged. Currently after
hotplug, min_free_kbytes will be set to a lower default and higher
default set when THP enabled is lost.
This change restores min_free_kbytes as expected for THP consumers.
The swap address_space doesn't have host. Thus, it makes kernel crash once
swap write meets error. Fix it.
Fixes: 735e4ae5ba28 ("vfs: track per-sb writeback errors and report them to syncfs") Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Jeff Layton <jlayton@kernel.org> Cc: Jan Kara <jack@suse.cz> Cc: Andres Freund <andres@anarazel.de> Cc: Matthew Wilcox <willy@infradead.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Cc: Dave Chinner <david@fromorbit.com> Cc: David Howells <dhowells@redhat.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20201010000650.750063-1-minchan@kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mmc_queue_setup_discard() the mmc driver queue's discard_granularity
might be set as 0 (when card->pref_erase > max_discard) while the mmc
device still declares to support discard operation. This is buggy and
triggered the following kernel warning message,
This patch fixes the issue by setting discard_granularity as SECTOR_SIZE
instead of 0 when (card->pref_erase > max_discard) is true. Now no more
complain from __blkdev_issue_discard() for the improper value of discard
granularity.
This issue is exposed after commit b35fd7422c2f ("block: check queue's
limits.discard_granularity in __blkdev_issue_discard()"), a "Fixes:" tag
is also added for the commit to make sure people won't miss this patch
after applying the change of __blkdev_issue_discard().
Fixes: e056a1b5b67b ("mmc: queue: let host controllers specify maximum discard timeout") Fixes: b35fd7422c2f ("block: check queue's limits.discard_granularity in __blkdev_issue_discard()"). Reported-and-tested-by: Vicente Bergas <vicencb@gmail.com> Signed-off-by: Coly Li <colyli@suse.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20201002013852.51968-1-colyli@suse.de Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2ed6edd33a21 ("perf: Add cond_resched() to task_function_call()")
looses any return value from smp_call_function_single() that is not
{0, -EINVAL}. This is a problem because it will return -EXNIO when the
target CPU is offline. Worse, in that case it'll turn into an infinite
loop.
The afs filesystem has a lock[*] that it uses to serialise I/O operations
going to the server (vnode->io_lock), as the server will only perform one
modification operation at a time on any given file or directory. This
prevents the the filesystem from filling up all the call slots to a server
with calls that aren't going to be executed in parallel anyway, thereby
allowing operations on other files to obtain slots.
[*] Note that is probably redundant for directories at least since
i_rwsem is used to serialise directory modifications and
lookup/reading vs modification. The server does allow parallel
non-modification ops, however.
When a file truncation op completes, we truncate the in-memory copy of the
file to match - but we do it whilst still holding the io_lock, the idea
being to prevent races with other operations.
However, if writeback starts in a worker thread simultaneously with
truncation (whilst notify_change() is called with i_rwsem locked, writeback
pays it no heed), it may manage to set PG_writeback bits on the pages that
will get truncated before afs_setattr_success() manages to call
truncate_pagecache(). Truncate will then wait for those pages - whilst
still inside io_lock:
Note that whilst afs_setattr() calls filemap_write_and_wait(), the fact
that the caller is holding i_rwsem doesn't preclude more pages being
dirtied through an mmap'd region.
Fix this by:
(1) Use the vnode validate_lock to mediate access between afs_setattr()
and afs_writepages():
(a) Exclusively lock validate_lock in afs_setattr() around the whole
RPC operation.
(b) If WB_SYNC_ALL isn't set on entry to afs_writepages(), trying to
shared-lock validate_lock and returning immediately if we couldn't
get it.
(c) If WB_SYNC_ALL is set, wait for the lock.
The validate_lock is also used to validate a file and to zap its cache
if the file was altered by a third party, so it's probably a good fit
for this.
(2) Move the truncation outside of the io_lock in setattr, using the same
hook as is used for local directory editing.
This requires the old i_size to be retained in the operation record as
we commit the revised status to the inode members inside the io_lock
still, but we still need to know if we reduced the file size.
Fixes: d2ddc776a458 ("afs: Overhaul volume and server record caching and fileserver rotation") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. A source port consumes more packet buffers than the watermark encoded
in SYS:PORT:ATOP_CFG.ATOP.
AND
2. Total memory use exceeds the consumption watermark encoded in
SYS:PAUSE_CFG:ATOP_TOT_CFG.
The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.
Fixes: a556c76adc05 ("net: mscc: Add initial Ocelot switch support") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We don't want ocelot_port_set_maxlen to enable pause frame TX, just to
adjust the pause thresholds.
Move the unconditional enabling of pause TX to ocelot_init_port. There
is no good place to put such setting because it shouldn't be
unconditional. But at the moment it is, we're not changing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To follow the model of felix and seville where we have one
platform-specific file, rename this file to the actual SoC it serves.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If someone calls setsockopt() twice to set a server key keyring, the first
keyring is leaked.
Fix it to return an error instead if the server key keyring is already set.
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The keyring containing the server's tokens isn't network-namespaced, so it
shouldn't be looked up with a network namespace. It is expected to be
owned specifically by the server, so namespacing is unnecessary.
Fixes: a58946c158a0 ("keys: Pass the network namespace into request_key mechanism") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
conn->state_lock may be taken in softirq mode, but a previous patch
replaced an outer lock in the response-packet event handling code, and lost
the _bh from that when doing so.
Fix this by applying the _bh annotation to the state_lock locking.
Fixes: a1399f8bb033 ("rxrpc: Call channels should have separate call number spaces") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If rxrpc_read() (which allows KEYCTL_READ to read a key), sees a token of a
type it doesn't recognise, it can BUG in a couple of places, which is
unnecessary as it can easily get back to userspace.
Fix this to print an error message instead.
Fixes: 99455153d067 ("RxRPC: Parse security index 5 keys (Kerberos 5)") Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The session key should be encoded with just the 8 data bytes and
no length; ENCODE_DATA precedes it with a 4 byte length, which
confuses some existing tools that try to parse this format.
Add an ENCODE_BYTES macro that does not include a length, and use
it for the key. Also adjust the expected length.
Note that commit 774521f353e1d ("rxrpc: Fix an assertion in
rxrpc_read()") had fixed a BUG by changing the length rather than
fixing the encoding. The original length was correct.
Fixes: 99455153d067 ("RxRPC: Parse security index 5 keys (Kerberos 5)") Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/ethernet/marvell/mvneta.c:3465:2: warning:
Attempt to free released memory
kfree(txq->buf);
^~~~~~~~~~~~~~~
When mvneta_txq_sw_init() fails to alloc txq->tso_hdrs,
it frees without poisoning txq->buf. The error is caught
in the mvneta_setup_txqs() caller which handles the error
by cleaning up all of the txqs with a call to
mvneta_txq_sw_deinit which also frees txq->buf.
Since mvneta_txq_sw_deinit is a general cleaner, all of the
partial cleaning in mvneta_txq_sw_deinit()'s error handling
is not needed.
Fixes: 2adb719d74f6 ("net: mvneta: Implement software TSO") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Pinned pages are not properly accounted particularly when
mapping error occurs on IOTLB update. Clean up dangling
pinned pages for the error path. As the inflight pinned
pages, specifically for memory region that strides across
multiple chunks, would need more than one free page for
book keeping and accounting. For simplicity, pin pages
for all memory in the IOVA range in one go rather than
have multiple pin_user_pages calls to make up the entire
region. This way it's easier to track and account the
pages already mapped, particularly for clean-up in the
error path.
Fix many (lots deleted here) build errors in hinic by selecting NET_DEVLINK.
ld: drivers/net/ethernet/huawei/hinic/hinic_hw_dev.o: in function `mgmt_watchdog_timeout_event_handler':
hinic_hw_dev.c:(.text+0x30a): undefined reference to `devlink_health_report'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x1c): undefined reference to `devlink_fmsg_u32_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_fw_reporter_dump':
hinic_devlink.c:(.text+0x126): undefined reference to `devlink_fmsg_binary_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_hw_reporter_dump':
hinic_devlink.c:(.text+0x1ba): undefined reference to `devlink_fmsg_string_pair_put'
ld: hinic_devlink.c:(.text+0x227): undefined reference to `devlink_fmsg_u8_pair_put'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_alloc':
hinic_devlink.c:(.text+0xaee): undefined reference to `devlink_alloc'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_free':
hinic_devlink.c:(.text+0xb04): undefined reference to `devlink_free'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_register':
hinic_devlink.c:(.text+0xb26): undefined reference to `devlink_register'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_devlink_unregister':
hinic_devlink.c:(.text+0xb46): undefined reference to `devlink_unregister'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_create':
hinic_devlink.c:(.text+0xb75): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xb95): undefined reference to `devlink_health_reporter_create'
ld: hinic_devlink.c:(.text+0xbac): undefined reference to `devlink_health_reporter_destroy'
ld: drivers/net/ethernet/huawei/hinic/hinic_devlink.o: in function `hinic_health_reporters_destroy':
Fixes: 51ba902a16e6 ("net-next/hinic: Initialize hw interface") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Bin Luo <luobin9@huawei.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Aviad Krawczyk <aviad.krawczyk@huawei.com> Cc: Zhao Chen <zhaochen6@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ethtool manual stated that the tx-timer is the "the amount of time the
device should stay in idle mode prior to asserting its Tx LPI". The
previous implementation for "ethtool --set-eee tx-timer" sets the LPI TW
timer duration which is not correct. Hence, this patch fixes the
"ethtool --set-eee tx-timer" to configure the EEE LPI timer.
The LPI TW Timer will be using the defined default value instead of
"ethtool --set-eee tx-timer" which follows the EEE LS timer implementation.
Changelog V2
*Not removing/modifying the eee_timer.
*EEE LPI timer can be configured through ethtool and also the eee_timer
module param.
*EEE TW Timer will be configured with default value only, not able to be
configured through ethtool or module param. This follows the implementation
of the EEE LS Timer.
Fixes: d765955d2ae0 ("stmmac: add the Energy Efficient Ethernet support") Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com> Signed-off-by: Voon Weifeng <weifeng.voon@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current neigh update event handler implementation takes reference to
neighbour structure, assigns it to nhe->n, tries to schedule workqueue task
and releases the reference if task was already enqueued. This results
potentially overwriting existing nhe->n pointer with another neighbour
instance, which causes double release of the instance (once in neigh update
handler that failed to enqueue to workqueue and another one in neigh update
workqueue task that processes updated nhe->n pointer instead of original
one):
Fix the bug by moving work_struct to dedicated dynamically-allocated
structure. This enabled every event handler to work on its own private
neighbour pointer and removes the need for handling the case when task is
already enqueued.
Fixes: 232c001398ae ("net/mlx5e: Add support to neighbour update flow") Signed-off-by: Vlad Buslov <vladbu@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When interface is attached while in promiscuous mode and with VLAN
filtering turned off, both configurations are not respected and VLAN
filtering is performed.
There are 2 flows which add the any-vid rules during interface attach:
VLAN creation table and set rx mode. Each is relaying on the other to
add any-vid rules, eventually non of them does.
Fix this by adding any-vid rules on VLAN creation regardless of
promiscuous mode.
Prior to this patch unloading an interface in promiscuous mode with RX
VLAN filtering feature turned off - resulted in a warning. This is due
to a wrong condition in the VLAN rules cleanup flow, which left the
any-vid rules in the VLAN steering table. These rules prevented
destroying the flow group and the flow table.
The any-vid rules are removed in 2 flows, but none of them remove it in
case both promiscuous is set and VLAN filtering is off. Fix the issue by
changing the condition of the VLAN table cleanup flow to clean also in
case of promiscuous mode.
Verify the configured FEC mode is supported by at least a single link
mode before applying the command. Otherwise fail the command and return
"Operation not supported".
Prior to this patch, the command was successful, yet it falsely set all
link modes to FEC auto mode - like configuring FEC mode to auto. Auto
mode is the default configuration if a link mode doesn't support the
configured FEC mode.
Fixes: b5ede32d3329 ("net/mlx5e: Add support for FEC modes based on 50G per lane links") Signed-off-by: Aya Levin <ayal@mellanox.com> Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Prior to this fix, in Striding RQ mode the driver was vulnerable when
receiving packets in the range (stride size - headroom, stride size].
Where stride size is calculated by mtu+headroom+tailroom aligned to the
closest power of 2.
Usually, this filtering is performed by the HW, except for a few cases:
- Between 2 VFs over the same PF with different MTUs
- On bluefield, when the host physical function sets a larger MTU than
the ARM has configured on its representor and uplink representor.
When the HW filtering is not present, packets that are larger than MTU
might be harmful for the RQ's integrity, in the following impacts:
1) Overflow from one WQE to the next, causing a memory corruption that
in most cases is unharmful: as the write happens to the headroom of next
packet, which will be overwritten by build_skb(). In very rare cases,
high stress/load, this is harmful. When the next WQE is not yet reposted
and points to existing SKB head.
2) Each oversize packet overflows to the headroom of the next WQE. On
the last WQE of the WQ, where addresses wrap-around, the address of the
remainder headroom does not belong to the next WQE, but it is out of the
memory region range. This results in a HW CQE error that moves the RQ
into an error state.
Solution:
Add a page buffer at the end of each WQE to absorb the leak. Actually
the maximal overflow size is headroom but since all memory units must be
of the same size, we use page size to comply with UMR WQEs. The increase
in memory consumption is of a single page per RQ. Initialize the mkey
with all MTTs pointing to a default page. When the channels are
activated, UMR WQEs will redirect the RX WQEs to the actual memory from
the RQ's pool, while the overflow MTTs remain mapped to the default page.
Fixes: 24163189da48 ("net/mlx5: Separate IRQ request/free from EQ life cycle") Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible that new command entry index allocation will temporarily
fail. The new command holds the semaphore, so it means that a free entry
should be ready soon. Add one second retry mechanism before returning an
error.
Patch "net/mlx5: Avoid possible free of command entry while timeout comp
handler" increase the possibility to bump into this temporarily failure
as it delays the entry index release for non-callback commands.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Eran Ben Elisha <eranbe@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Once driver detects a command interface command timeout, it warns the
user and returns timeout error to the caller. In such case, the entry of
the command is not evacuated (because only real event interrupt is allowed
to clear command interface entry). If the HW event interrupt
of this entry will never arrive, this entry will be left unused forever.
Command interface entries are limited and eventually we can end up without
the ability to post a new command.
In addition, if driver will not consume the EQE of the lost interrupt and
rearm the EQ, no new interrupts will arrive for other commands.
Add a resiliency mechanism for manually polling the command EQ in case of
a command timeout. In case resiliency mechanism will find non-handled EQE,
it will consume it, and the command interface will be fully functional
again. Once the resiliency flow finished, wait another 5 seconds for the
command interface to complete for this command entry.
Define mlx5_cmd_eq_recover() to manage the cmd EQ polling resiliency flow.
Add an async EQ spinlock to avoid races between resiliency flows and real
interrupts that might run simultaneously.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Upon command completion timeout, driver simulates a forced command
completion. In a rare case where real interrupt for that command arrives
simultaneously, it might release the command entry while the forced
handler might still access it.
Fix that by adding an entry refcount, to track current amount of allowed
handlers. Command entry to be released only when this refcount is
decremented to zero.
Command refcount is always initialized to one. For callback commands,
command completion handler is the symmetric flow to decrement it. For
non-callback commands, it is wait_func().
Before ringing the doorbell, increment the refcount for the real completion
handler. Once the real completion handler is called, it will decrement it.
For callback commands, once the delayed work is scheduled, increment the
refcount. Upon callback command completion handler, we will try to cancel
the timeout callback. In case of success, we need to decrement the callback
refcount as it will never run.
In addition, gather the entry index free and the entry free into a one
flow for all command types release.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As part of driver unload, it destroys the commands EQ (via FW command).
As the commands EQ is destroyed, FW will not generate EQEs for any command
that driver sends afterwards. Driver should poll for later commands status.
Driver commands mode metadata is updated before the commands EQ is
actually destroyed. This can lead for double completion handle by the
driver (polling and interrupt), if a command is executed and completed by
FW after the mode was changed, but before the EQ was destroyed.
Fix that by using the mlx5_cmd_allowed_opcode mechanism to guarantee
that only DESTROY_EQ command can be executed during this time period.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters") Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by: Moshe Shemesh <moshe@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling pipe2() with O_NOTIFICATION_PIPE could results in memory
leaks unless watch_queue_init() is successful.
In case of watch_queue_init() failure in pipe2() we are left
with inode and pipe_inode_info instances that need to be freed. That
failure exit has been introduced in commit c73be61cede5 ("pipe: Add
general notification queue support") and its handling should've been
identical to nearby treatment of alloc_file_pseudo() failures - it
is dealing with the same situation. As it is, the mainline kernel
leaks in that case.
Another problem is that CONFIG_WATCH_QUEUE and !CONFIG_WATCH_QUEUE
cases are treated differently (and the former leaks just pipe_inode_info,
the latter - both pipe_inode_info and inode).
Fixed by providing a dummy wacth_queue_init() in !CONFIG_WATCH_QUEUE
case and by having failures of wacth_queue_init() handled the same way
we handle alloc_file_pseudo() ones.
Fixes: c73be61cede5 ("pipe: Add general notification queue support") Signed-off-by: Qian Cai <cai@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Mbox implementation in octeontx2 driver has three states
alloc, send and reset in mbox response. VF allocate and
sends message to PF for processing, PF ACKs them back and
reset the mbox memory. In some case we see synchronization
issue where after msgs_acked is incremented and before
mbox_reset API is called, if current execution is scheduled
out and a different thread is scheduled in which checks for
msgs_acked. Since the new thread sees msgs_acked == msgs_sent
it will try to allocate a new message and to send a new mbox
message to PF.Now if mbox_reset is scheduled in, PF will see
'0' in msgs_send.
This patch fixes the issue by calling mbox_reset before
incrementing msgs_acked flag for last processing message and
checks for valid message size.
Fixes: d424b6c02 ("octeontx2-pf: Enable SRIOV and added VF mbox handling") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently in otx2_open on failure of nix_lf_start
transmit queues are not stopped which are already
started in link_event. Since the tx queues are not
stopped network stack still try's to send the packets
leading to driver crash while access the device resources.
Fixes: 50fe6c02e ("octeontx2-pf: Register and handle link notifications") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For TCP/UDP checksum offload feature in Octeontx2
expects L3TYPE to be set irrespective of IP header
checksum is being offloaded or not. Currently for
IPv6 frames L3TYPE is not being set resulting in
packet drop with checksum error. This patch fixes
this issue.
Fixes: 3ca6c4c88 ("octeontx2-pf: Add packet transmission support") Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Packet replication feature present in Octeontx2
is a hardware linked list of PF and its VF
interfaces so that broadcast packets are sent
to all interfaces present in the list. It is
driver job to add and delete a PF/VF interface
to/from the list when the interface is brought
up and down. This patch fixes the
npc_enadis_default_entries function to handle
broadcast replication properly if packet replication
feature is present.
Fixes: 40df309e4166 ("octeontx2-af: Support to enable/disable default MCAM entries") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Geetha sowjanya <gakula@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. These two pins can config via
4.7k-ohm resistor to 3.3V hw setting, but also config via software setting
(extension page 0xa4 register 0x1c bit13 12 and 11).
This table describes how to config these hw pins via external pull-high or pull-
low resistor.
It is a misunderstanding that mapping it as register bits below:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
So I removed these descriptions above and add related settings as below:
14 = reserved
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay
10:0 = Test && debug settings reserved by realtek
Test && debug settings are not recommend to modify by default.
Fixes: f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config") Signed-off-by: Willy Liu <willy.liu@realtek.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Open vSwitch and Linux bridge will disable LRO of the interface
when this interface added to them. Now when disable the LRO, the
virtio-net csum is disable too. That drops the forwarding performance.
Fixes: a02e8964eaf9 ("virtio-net: ethtool configurable LRO") Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Jason Wang <jasowang@redhat.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adds the missing .stop entry in the Belkin driver_info structure.
Fixes: e20bd60bf62a ("net: usb: asix88179_178a: Add support for the Belkin B2B128") Signed-off-by: Wilken Gottwalt <wilken.gottwalt@mailbox.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If mlxsw_sp_acl_tcam_group_id_get() fails, the mutex initialized earlier
is not destroyed.
Fix this by initializing the mutex after calling the function. This is
symmetric to mlxsw_sp_acl_tcam_group_del().
Fixes: 5ec2ee28d27b ("mlxsw: spectrum_acl: Introduce a mutex to guard region list updates") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
