Right now, both ltq-adsl-mei and ltq-vdsl-mei are always built, even
when they aren't necessary for the selected variant. This can cause the
build to fail, for example ltq-vdsl-mei doesn't build successfully here
on xway target due to the vectoring callback.
Make these dependencies conditional on the specific package variants,
so they are only built when actually needed.
Signed-off-by: Jan Hoffmann <jan@3e8.eu> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(cherry picked from commit 2f484aeff5fe5ba3a832f98ca409adde3257e832)
Jan Hoffmann [Sun, 13 Mar 2022 21:14:38 +0000 (22:14 +0100)]
ltq-vdsl-mei: add locking to interrupt handler
Some users noticed repeated resyncs at random intervals, which go away
when the MEI driver is configured to use polling instead of interrupts.
Debugging shows that this seems to be caused by concurrent calls to
MEI_ReadMailbox (in the interrupt handler) and MEI_WriteMailbox. This
appears to be mostly triggered when there is an interrupt for vectoring
error reports.
In polling mode, calls to MEI_ReadMailbox are protected by the same
semaphore as is used in MEI_WriteMailbox. When interrupts are used,
MEI_WriteMailbox appears to rely on MEI_DisableDeviceInt and
MEI_EnableDeviceInt to provide mutual exclusion with the interrupt
handler. These functions mask/unmask interrupts, and there is an
additional check of the mask in the interrupt handler itself. However,
this is not sufficient on systems with SMP, as the interrupt handler
may be running in parallel, and could already be past the interrupt
mask check at this point.
This adds a lock to the interrupt handler, and also acquires this lock
in MEI_DisableDeviceInt. This should make sure that after a call to
MEI_DisableDeviceInt the interrupt is masked, and the interrupt handler
is either not running, has alread finished its work, or is still before
the interrupt mask check, and is thus going to detect the change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit 17004245534731ab03c9a8683208e84d9c399979)
Jan Hoffmann [Sun, 13 Mar 2022 21:14:37 +0000 (22:14 +0100)]
ltq-vdsl-app: set MAC address for vectoring error reports
This tells the modem about the WAN MAC address, which is used as source
address for vectoring error reports that are generated by the firmware.
It needs to be set early, as the MEI driver only actually writes the
value to the modem when is in reset state (i.e. the firmware has been
loaded, but connection has not started yet).
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit b35d33c8b8a7b96f06179982b5d944cde7234004)
This re-enables the vectoring error sample callback and adds a
dependency to the corresponding driver.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit 93f0e1f922ec1351d429259db942f10147e624ff)
Jan Hoffmann [Sun, 13 Mar 2022 21:14:35 +0000 (22:14 +0100)]
ltq-vectoring: add driver
In order to calculate the required pre-distortion for downstream
vectoring, the vectoring control entity (VCE) at the carrier office
needs error samples from the modem. On Lantiq VR9 modems, error reports
are generated by the firmware, but need to be multiplexed into the data
stream by the driver on the main processor when L2 encapsulation is
selected by the VCE.
This driver provides the necessary callback function, which is called by
the MEI driver after receiving an error report from the firmware.
Originally, it is part of the Lantiq PPA driver, but after a few changes
it also works with the PTM driver used in OpenWrt. The direct call to
ndo_start_xmit needs to be replaced, as the PTM driver relies on locks
from the kernel. Instead dev_queue_xmit is used, which is called from a
work queue, as it is not safe to call from an interrupt handler.
Additional changes include fixes to support recent kernel versions and
a change of the used interface from ptm0 to dsl0.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jan Hoffmann <jan@3e8.eu>
(cherry picked from commit f872b966092ece5c0e2192e0d979a9eb69283f17)
A GPIO assert is required to reset the system. Otherwise, the system
will hang on reboot.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit a2817ce96f17db3a5af77837ae5733b47182ae0d)
Tested in a DGS-1210-28 F3, both triggering failsafe and reboot.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
(cherry picked from commit b85f59b726442621efb95153ff60b8767723feca)
Arınç ÜNAL [Wed, 4 May 2022 08:34:29 +0000 (11:34 +0300)]
packages: nvram: add NVRAM quirks for bcm53xx target
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Flashing instructions:
* Boot to CFE Recovery Mode by holding the reset button while power-on.
* Connect to the router with an ethernet cable.
* Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
* Head to http://192.168.1.1.
* Reset NVRAM.
* Upload the OpenWrt image.
CFE bootloader may reject flashing the image due to image integrity check.
In that case, follow the instructions below.
* Rename the OpenWrt image as firmware.trx.
* Run a TFTP server and make it serve the firmware.trx file.
* Run the URL below on a browser or curl.
http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
[rmilecki: mark BROKEN until we sort out nvram & CFE recovery] Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 72b9b721d707b7f70109eb70b2a9f22449ceba08)
Raylynn Knight [Tue, 17 May 2022 03:15:54 +0000 (23:15 -0400)]
realtek: add support for ZyXEL GS1900-24E
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Stijn Tintel [Tue, 17 May 2022 14:57:07 +0000 (17:57 +0300)]
ramips: use hotplug script for EAP615-Wall MACs
Using nvmem-cells to set the MAC address for a DBDC device results in
both PHY devices using the same MAC address. This in turn will result in
multiple BSSes using the same BSSID, which can cause various problems.
Use the hotplug script for the EAP615-Wall instead to avoid this.
Fixes: a1b8a4d7b3ff ("ramips: support TP-Link EAP615-Wall") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-By: Andrew Powers-Holmes <aholmes@omnom.net>
(cherry picked from commit ce90ba1f3168e3f4581fd8581e2c0cd31efa14cf)
Daniel Golle [Sun, 5 Jun 2022 10:28:11 +0000 (11:28 +0100)]
tools/mkimage: increase tmpfile name length limit
mkimage limits the length of the file paths in can deal with to 256
characters. Turns out that in automated builds by asu we break this
limit, so increase it to 1024 characters.
David Bauer [Wed, 25 May 2022 20:07:10 +0000 (22:07 +0200)]
ipq40xx: add Aruba AP-365 specific BDF
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.
The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.
Replace the BDF with the one extracted from Arubas kernel.
Hauke Mehrtens [Sat, 28 May 2022 12:32:08 +0000 (14:32 +0200)]
malta: use default OpenWrt network configuration
Currently malta configures the first Ethernet device as WAN interface.
If it finds a second one it will configure it as LAN.
This commit reverses it to match armvirt and x86. If there is only one
network device it will be configured as LAN device now. If we find two
network devices the 2. one will be WAN.
If no board.d network configuration is given it will be configured in
package/base-files/files/etc/board.d/99-default_network
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[minor typos] Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit fb1ba922026a4b7d04ef5c8058f7890ed7b790e6)
Jo-Philipp Wich [Tue, 31 May 2022 08:43:53 +0000 (10:43 +0200)]
firewall4: update to latest Git HEAD
210991d fw4: prefer /dev/stdin if available 4e5e322 fw4: make `fw4 restart` behavior more robust 221040e ruleset: emit time ranges when both start and stop times are specified 30a7d47 fw4: fix datetime parsing fb9a6b2 ruleset: correct mangle_output chain type 6dd2617 fw4: fix logic flaw in testing hw flow offloading support c7c9c84 fw4: ensure that negative bitcounts are properly translated c4a78ed fw4: fix typo in emitted set types
Jo-Philipp Wich [Tue, 31 May 2022 08:59:47 +0000 (10:59 +0200)]
ucode: update to latest Git HEAD
d996047 syntax: adjust number literal parsing and string to number conversion 9efbe18 lib: refactor `uc_int()` da3f089 lib: rework uc_index() implementation 559029e ci: make jobs faster during pull request testing
Update the name of for the Ubiquiti NanoBeam M5 to match the
auto-generated one at runtime. Otherwise sysupgrade complains about
mismatching device names.
Ubiquiti NanoBeam M5 devices are CPE equipment for customer locations
with one Ethernet port and a 5 GHz 300Mbps wireless interface.
Specificatons:
- Atheros AR9342
- 535 MHz CPU
- 64 MB RAM
- 8 MB Flash
- 1x 10/100 Mbps Ethernet with passive PoE input (24 V)
- 6 LEDs of which four are rssi
- 1 reset button
- UART (4-pin) header on PCB
Notes:
The device was supported by OpenWrt in ar71xx.
Flash instructions (web/ssh/tftp):
Loading the image via ssh vias a stock firmware prior "AirOS 5.6".
Downgrading stock is possible.
* Flashing is possible via AirOS software update page:
The "factory" ROM image is recognized as non-native and then installed correctly.
AirOS warns to better be familiar with the recovery procedure.
* Flashing can be done via ssh, which is becoming difficult due to legacy
keyexchange methods.
This is an exempary ssh-config:
KexAlgorithms +diffie-hellman-group1-sha1
HostKeyAlgorithms ssh-rsa
PubkeyAcceptedKeyTypes ssh-rsa
User ubnt
The password is ubnt.
Connecting via IPv6 link local worked best for me.
1. scp the factory image to /tmp
2. fwupdate.real -m /tmp/firmware_image_file.bin -d
* Alternatively tftp is possible:
1. Configure PC with static IP 192.168.1.2/24.
2. Enter the rescue mode. Power off the device, push the reset button on
the device (or the PoE) and keep it pressed.
Power on the device, while still pushing the reset button.
3. When all the leds blink at the same time, release the reset button.
4. Upload the firmware image file via TFTP:
tftp 192.168.1.20
tftp> bin
tftp> trace
Packet tracing on.
tftp> put firmware_image.bin
Maciej Krüger [Thu, 19 May 2022 18:00:53 +0000 (20:00 +0200)]
ath79: add support for MikroTik hAP (RB951Ui-2nD)
The MikroTik hAP (product code RB951Ui-2nD) is
an indoor 2.4Ghz AP with a 2 dBi integrated antenna built around the
Atheros QCA9531 SoC.
Specifications:
- SoC: Atheros QCA9531
- RAM: 64 MB
- Storage: 16 MB NOR - Winbond 25Q128FVSG
- Wireless: Atheros QCA9530 (SoC) 802.11b/g/n 2x2
- Ethernet: Atheros AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 8 user-controllable LEDs:
· 1x power (green)
· 1x user (green)
· 4x LAN status (green)
· 1x WAN status (green)
· 1x PoE power status (red)
See https://mikrotik.com/product/RB951Ui-2nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Thibaut VARÈNE [Mon, 2 May 2022 15:07:45 +0000 (17:07 +0200)]
ath79: add support for MikroTik RouterBOARD hAP ac lite
The MikroTik RB952Ui-5ac2nD (sold as hAP ac lite) is an indoor 2.4Ghz
and 5GHz AP/router with a 2 dBi integrated antenna.
See https://mikrotik.com/product/RB952Ui-5ac2nD for more details.
Specifications:
- SoC: QCA9533
- RAM: 64MB
- Storage: 16MB NOR
- Wireless: QCA9533 802.11b/g/n 2x2 / QCA9887 802.11a/n/ac 2x2
- Ethernet: AR934X switch, 5x 10/100 ports,
10-28 V passive PoE in port 1, 500 mA PoE out on port 5
- 6 user-controllable LEDs:
- 1x user (green)
- 5x port status (green)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. The "Internet"
port (port number 1) must be used to upload the TFTP image, then
connect to any other port to access the OpenWRT system.
Follow common MikroTik procedure as in
https://openwrt.org/toh/mikrotik/common.
Jo-Philipp Wich [Tue, 17 May 2022 19:01:46 +0000 (21:01 +0200)]
firewall4: update to latest Git HEAD
c22eeef fw4: support negative CIDR bit notation 628d791 hotplug: reliably handle interfaces with ubus zone hints d005293 fw4: store zone associations from ubus in statefile as well b268225 fw4: filter non hw-offload capable devices when resolving lower devices 57984e0 fw4: always resolve lower flowtable devices 7782017 tests: fix mocked `fd.read("line")` api 72b196d config: remove restictions on DHCPv6 allow rule f0cc317 fw4: refactor family selection for forwarding rules b0b8122 treewide: use modern syntax 05995f1 fw4: fix emitting device jump rules for family restricted zones b479815 fw4: fix family auto-selection for config nat rules 2816a82 ruleset: ensure that family-agnostic ICMP rules cover ICMPv6 as well 2379c3d tests: add test coverage for zone family selection logic
This is mostly a bug fix release, including two that were already
patched here:
- 300-fix-SSL_get_verify_result-regression.patch
- 400-wolfcrypt-src-port-devcrypto-devcrypto_aes.c-remove-.patch
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4:ab:82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4:ab:82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4:ab:82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4:ab:82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4:ab:82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4:ab:82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch] Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit f8b0010dfb548469686049f85076fd6a3a6bca2e)
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Installation instruction:
0. Make sure you have latest original firmware (3.7.11.4)
1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232
(9600,8N1)
screen /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal
2. Configure your IP-Address to 192.168.1.42
3. When device boots hit spacebar
3. Configure the device for tftpboot
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.42
saveenv
4. Reset the device
reset
5. Hit again the spacebar
6. Now load the image via tftp:
tftpboot 0x81000000 INITRAMFS.bin
7. Boot the image:
bootm 0x81000000
8. Copy the squashfs-image to the device.
9. Do a sysupgrade.
https://openwrt.org/toh/netgear/wndap360
The device should be converted from kmod-owl-loader to nvmem-cells in the
future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing.
That is why this commit is still using kmod-owl-loader. In the future
the device tree may look like this:
Foica David [Thu, 21 Apr 2022 01:20:57 +0000 (04:20 +0300)]
ath79: add support for TP-Link Deco M4R v1 and v2
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.
The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.
There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.
Pre-requisites:
- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.
Installation:
- Unplug your router and turn it upside down. Using a long and thin object
like a SIM unlock tool, press and hold the reset button on the router and
replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
Choose the debug firmware that you downloaded and flash it. Wait until the
router reboots (at this stage you can remove the static IP).
- Open a terminal window and connect to the router via telnet (the primary
router should have a 192.168.0.1 IP address, secondary routers are
different).
- Transfer the file over to the router, you can use curl to download it
from the internet (use the insecure flag and make sure your source accepts
insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
separated. We can use dd to split the OpenWrt image file and flash it with
mtd:
- Once the images are ready, you have to flash the device using mtd
(make sure to flash the correct partitions or you may be left with a
hard bricked router):
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup] Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4a8eaa5c7c9235212c4af022c18b2dfbadfe557f)
Andreas Böhler [Mon, 22 Mar 2021 00:01:44 +0000 (01:01 +0100)]
ramips: Add support for SERCOMM NA502S
The SERCOMM NA502s is a smart home gateway manufactured by SERCOMM and sold
under different brands (among others, A1 Telekom Austria SmartHome Premium
Gateway). It has multi-protocol radio support in addition to LAN and WiFi.
LAN MAC is read from the config partition, WiFi 2.4GHz is LAN+2 and matches
the OEM firmware. WiFi 5GHz with LAN+1 is an educated guess since the
OEM firmware does not enable 5GHz WiFi.
Installation
------------
Attach serial console, then boot the initramfs image via TFTP.
Once inside OpenWrt, run sysupgrade -n with the sysupgrade file.
Attention: The device has a dual-firmware design. We overwrite kernel2,
since kernel1 contains an automatic recovery image.
If you get NAND ECC errors and are stuck with bad eraseblocks, try to
erase the mtd partition first with
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.
Hardware
--------
SoC: Mediatek MT7621A
RAM: 128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
- 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
- 1x MT7615NE (4x4:4) 5GHz
- 8 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 3.0 port
UART:
- 57600-8-N-1
J4
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)
Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006)
WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000)
WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:65
In OEM firmware the DBDC wifi interfaces have these mac addresses:
2G) 82:XX:XX:XX:XX:65
5G) 80:XX:XX:XX:XX:65
While in OpenWrt the addresses are:
2G) 80:XX:XX:XX:XX:65
5G) 02:XX:XX:XX:XX:65
2) radio0 will show as 2G/5G interface but only 2G is really usable.
3) There is just one wifi led for all wifi interfaces.
It currently shows only the radio0 GHz wifi activity.
4) My unit was shipped with M33A8.V5030.190716 firmware which contains
the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
the input box it will start the telnet daemon. Now you can access
the telnet console on port 2323 with these credentials:
username: admin2860
password: admin
5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
webcmd.shtml page. If your router is shipped with a previous firmware
version and you want to back it up, you can follow the back up
procedure of the WS-WN583A6.
TP-Link RE650 v2 is largely similar to v1 that
is already supported by OpenWrt. Notable differences
is differnt SPI Flash - 8 MB instead of 16 MB
(from cFeon instead of Winbond) and a different
configuration of PCIE connections to wifi chips.
Otherwise it's largely the same product as v1
Hardware specification:
- SoC 880 MHz - MediaTek MT7621AT
- 128 MB of DDR3 RAM
- 8 MB - cFeon QH64A-104HIP
- 4T4R 2.4 GHz - MediaTek MT7615E
- 4T4R 5 GHz - MediaTek MT7615E
- 1x 1 Gbps Ethernet - MT7621AT integrated
- 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2))
- 4x buttons (Reset, Power, WPS, LED)
- UART pinout - GND, RX, TX, labeled in the middle of the PCB,
requires soldering because they're not through holes.
Serial console @ 57600,8n1
Flash instructions:
Upload
openwrt-ramips-mt7621-tplink_re650-v2-squashfs-factory.bin
from the RE650 web interface.
TFTP recovery to stock firmware:
I didn't try recovering back to the stock firmware, however,
if there is such process for other RExxx devices, it seems like
it could be similar here.
Clemens Hopfer [Thu, 22 Jul 2021 15:54:15 +0000 (17:54 +0200)]
ramips: add support for YunCore AX820/HWAP-AX820
There are two versions which are identical apart from the enclosure:
YunCore AX820: indoor ceiling mount AP with integrated antennas
YunCore HWAP-AX820: outdoor enclosure with external (N) connectors
Flash instructions:
The "OpenWRT support" version of the AX820 comes with a LEDE-based
firmware with proprietary MTK drivers and a luci webinterface and
ssh accessible under 192.168.1.1 on LAN; user root, no password.
The sysupgrade.bin can be flashed using luci or sysupgrade via ssh,
you will have to force the upgrade due to a different factory name.
Remember: Do *not* preserve factory configuration!
MAC addresses as used by OEM firmware:
use address source
2g 44:D1:FA:*:0b Factory 0x0004 (label)
5g 46:D1:FA:*:0b LAA of 2g
lan 44:D1:FA:*:0c Factory 0xe000
wan 44:D1:FA:*:0d Factory 0xe000 + 1
The wan MAC can also be found in 0xe006 but is not used by OEM dtb.
Due to different MAC handling in mt76 the LAA derived from lan is used
for 2g to prevent duplicate MACs when creating multiple interfaces.
Andreas Böhler [Sun, 15 May 2022 08:50:31 +0000 (10:50 +0200)]
IPQ4019: AVM FRITZ!Box 7530: Remove NAND ECC restrictions from DTS
Some revisions of the FRITZ!7530 use a Toshiba NAND with 8 bit ECC in
contrast to the Macronix NAND with 4 bit ECC. This removes the hardcoded
ECC strength and step size as set in qcom-ipq4019.dtsi, thus relying on the
kernel NAND detection routines to correclty set up the ECC parameters.
Andreas Böhler [Tue, 12 Apr 2022 09:01:25 +0000 (11:01 +0200)]
kernel: add support for Toshiba TC58NVG0S3HTA00 NAND flash
The Toshiba TC58NVG0S3HTA00 is detected with 64 byte OOB while the flash
has 128 byte OOB. This adds a static NAND ID entry to correct this.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
(cherry picked from commit 0bc794a66845738eef7eeb7e13877ffb8aec17f7) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ZTE MF286A and MF286R feature a "power switch override" GPIO in stock
firmware as means to prevent power interruption during firmware update,
especially when used with internal battery.
To ensure that this GPIO is
properly driven as in stock firmware, configure it with userspace GPIO
switch.
It was observed that on some units, the modem would not be
restarted together with the board itself on reboot, this should help
with that as well.
On GL-AR300M Series GPIO17 described as I2C SDA in Device Tree.
Because of GPIO_OUT_FUNCTION4 register was not initialized on start,
GPIO17 was uncontrollable, it always in high state. According to QCA9531
documentation, default setting of GPIO17 is SYS_RST_L. In order to make
GPIO17 controllable, it should write value 0x00 on bits [15:8] of
GPIO_OUT_FUNCTION4 register, located at 0x1804003C address.
ipq40xx: Lyra: update RGB LED-Controller node for 5.10+
Add the reg and color property to each channel node. This
update is to accommodate the multicolor framework.
Refer to:
<https://lore.kernel.org/all/20200622185919.2131-9-dmurphy@ti.com>
<https://lore.kernel.org/all/20210818070209.1540451-1-michal.vokac@ysoft.com>
Note:
There is only a single extremely bright RGB-LED.
The RGB-color channels (i.e.: blue-0, blue-1 and blue-2)
are running in parallel to increase the current delivery
beyond what a single PWM-output on the LED controller
could do.
None of the devices supported by target xway are using Realtek
RTL8366S, RTL8367A and RTL8367B switches. The switches mentioned
earlier were enabled when bumping the kernel version to 3.7 in
commit 3a948770cf46 ("add linux-v3.7").
Switches used by individual devices are listed below.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
(checkpatch.pl fixes) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 8b5d2a73255298b916259ccbc609e4667a335844)
Do not reset the RTL930x SerDes on link changes, instead set up
the SDS with internal PHYs for the SFP+ ports only.
This fixes the 8 1GBit ports on the Zyxel XGS1250 which
do not work without this patch.
A complete SerDes reset was performed on all SerDes links. For copper
1Gbit ports, this is commonly a single XGMII link to an RTL8218D. There
is however no support for setting up the XGMII link on RTL9300/RTL9310,
thereby wiping the (RX/TX) setup done by u-boot and breaking the 1GBit
ports. No SerDes reset should be done for these links.
The handling of SGMII/HiSGMII, 1000BX or 10GR links is actually entirely
different. All these modes need to be suitably RX calibrated and the
pre- main and post- amplifiers set up properly for TX.
The 10GBit SFP+ fiber links are recalibrated instead of reset, which
e.g. is necessary when someone pulls a module out and puts another in.
This makes swapping out 10GBit fiber modules possible. 1GBit modules are
not yet supported, nor any modules with an internal phy.
Piotr Dymacz [Wed, 6 Apr 2022 21:07:55 +0000 (23:07 +0200)]
bcm27xx: include 'rtc' in target's 'FEATURES'
There are many ways to add external RTC to Raspberry Pi boards. Let's
include support for this for the whole target and while at it, sort
features alphabetically.
Tiago Gaspar [Wed, 4 May 2022 09:36:07 +0000 (10:36 +0100)]
firewall: config: remove restictions on DHCPv6 allow rule
Remove restrictions on source and destination addresses, which aren't
specified on RFC8415, and for some reason in openwrt are configured
to allow both link-local and ULA addresses.
As cleared out in issue #5066 there are some ISPs that use Gloabal
Unicast addresses, so fix this rule to allow them.
Daniel Golle [Mon, 2 May 2022 20:07:16 +0000 (21:07 +0100)]
base-files: simplify restorecon logic
Remove forgotten redundant selinuxenabled call and skip the whole
thing in case $IPKG_INSTROOT is set as labels are anyway applied only
later on in fakeroot when squashfs is created.
Fixes: 6d7272852e ("base-files: add missing $IPKG_INSTROOT to restorecon call") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7b07c3cff57f057d6780d34adeb23c06123732db)
try to clean up some labeling inconsistencies
iwinfo loose ends
ucode loose ends
Makefile: adjust mintesttgt (adds blockmount/blockd)
nftables: reads inherited netifd pipe
ucode: reads inherited netifd pipes
mountroot: fowner
sandbox: writes inherited dropbear pipes
unbound related to /tmp/etc/ssl
unbound loose ends
adds a sslconftmpfile for /tmp/etc/ssl
README: maintain a wish list in the README
iwinfo: netifd forgot write
gptfdisk loose ends
iwinfo: netifd wpad reads/writes inherited netifd fifo files
netifd (mac80211.sh) executes iwinfo
luci: executes wireguard
luci-cgi: audits xtables execute access
rcuhttpd: lists ssl certfile dirs
iwinfo, wifi,nftables usage of ttyd pty if available
urandomseed: seedrng needs cap_sys_admin
iwinfo iwinfo, nftables and some chronyd rules related to ntp nts server
nftables, wifi and adds iwinfo skel
nftables, rpcd, ucode
nftables, ucode and seedrng ucode, fw3/nftables, luci
adds ucode skel and some fw3/nftables related
urandomseed: some seedrng rules
fw3 adds some support for fw4
urandomseed: /etc/seedrng is for seed.credit
hotplugcal: runs ucode which is interpreter like
adds a nftables skeleton and makes xtables optional
agent: allow all agents to write inherited dropbear pipes
urandomseed: this seems to be replaced by seedrng
kmodloader: label /etc/modules.conf kmodloader.conffile
Revert "shelexecfile: remove auditallow rule"
Makefile: sort the modules to process by secilc
Moves back to git.defensec.nl
unbound odhcpd (ip) reads net proc
tcp dump
shelexecfile: remove auditallow rule
rrd.cil: fixes indent
Target rddtool from cgi-io instead of runnit it without transition
rrd.cil related
rrd, rpcd, cgiio clean ups related to luci-app-statistics
Rules for rrd files and luci-statistics
unboundcontrol ordering
Several missing permissions
blockmount, dnsmasq, hotplugcall, rpcd, unbound
adds mctp_socket (linux 5.15)
ip: forgot tc-tiny type transition to go along with the fc spec
ip: adds a fc spec for tc-tiny (called by sqm)
adds ttyACM fc spec and various assorted loose ends
.gitattributes: do not export the github workflows
workflow use selinux 3.3
project moved back to https://git.defensec.nl/selinux-policy.git
Daniel Golle [Mon, 2 May 2022 18:58:56 +0000 (19:58 +0100)]
base-files: add missing $IPKG_INSTROOT to restorecon call
Update to overlooked v2 version of Dominick Grift's patch.
Fixes: 5109bd164c ("base-files: address sed in-place without SELinux awareness") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 6d7272852e0b2634b2fa93a131ea8659ec87f079)
ipq40xx: fix BDF file for pcie wifi chip on the GL.Inet GL-B2200
After the switch to pre-calibration, ath10k would fail to initialize
the PCIE Wi-Fi on the GL-B200 as follows:
ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000
[...]
ath10k_pci 0000:01:00.0: failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=GL-B2200 from ath10k/QCA9888/hw2.0/board-2.bin
ath10k_pci 0000:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9888/hw2.0
ath10k_pci 0000:01:00.0: failed to fetch board file: -12
ath10k_pci 0000:01:00.0: could not probe fw (-12)
Repackage the BDF file after renaming relevant fields and files to
allow for the Wi-Fi interface to start again.
Fixes: 80d34d9d593 ("ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200") CC: Christian Lamparter <chunkeey@gmail.com> CC: Robert Marko <robimarko@gmail.com> Reviewed-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
(cherry picked from commit e3f9af4fb6e4ba8bf54cb4240f318ad32260a6fa)
Martin Kennedy [Tue, 26 Apr 2022 21:04:06 +0000 (17:04 -0400)]
mpc85xx: Fix output location of padded dtb
In commit 7e614820a892 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
Fixes: 7e614820a892 ("mpc85xx: add support for Extreme Networks WS-AP3825i") Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(cherry picked from commit 1d06277407d3e294589ecde46328303a9f3803fd)
Fixes: db34b93331e9 (add a version that can be bumped to force toolchain/target rebuild) Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
(cherry picked from commit aeaa816cd2bd22de165c71a41d8d198a9235e971)
ath79: ZTE MF286R: add comgt-ncm to DEVICE_PACKAGES
When adding support to the router's built-in modem, this required
package was omitted, because it was already enabled in the image
configuration in use for testing, and this went unnoticed.
In result, the modem still isn't fully supported in official images.
As it is the primary WAN interface, add the missing package.
Fixes: e02fb42c53ba ("comgt: support ZTE MF286R modem") Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 8a1003c5986514d7a78f78b3ee94003837d82582)
Alban Bedel [Sat, 30 Apr 2022 08:42:33 +0000 (10:42 +0200)]
ramips: zbt-wg2626: Add the reset gpio for PCIe port 1
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Nick Hainke [Mon, 18 Apr 2022 13:04:25 +0000 (15:04 +0200)]
ipq40xx: 5.10: fix ar40xx driver
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.
Suggested-by: Serhii Serhieiev <adron@mstnt.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit ab7e53e5cce703c7a62efbe1d41fb94c2228a178)
David Bauer [Sun, 24 Apr 2022 23:00:49 +0000 (01:00 +0200)]
mpc85xx: set WS-AP3825i mac-address in preinit
The bootloader does seem to not correctly patch in the MAC address for
eth0 / eth1 in some cases. While the root cause is not known, manually
applying the MAC-Address in preinit does not hurt.
Reported-by: Tom Herbers <freifunk@tomherbers.de> Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit c6d52515e009d96e0afbe77310bf172f113d0eef)
David Bauer [Sun, 24 Apr 2022 21:48:42 +0000 (23:48 +0200)]
mpc85xx: define reset-delay for WS-AP3825i eth PHY
The WS-AP3825i uses Atheros PHYs which according to the datasheet
require the reset to be asserted for at least 1 ms.
This fixes broken eth1 upon soft-reboot. eth0 is no affected, as the
ifup / ifdown cycle in preinit prevents this issue from happening when
the system is ready.
Reported-by: Tom Herbers <freifunk@tomherbers.de> Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8b3c313515c1ae37be9d61a4e92c4bf4b43f605f)
Jo-Philipp Wich [Tue, 22 Mar 2022 19:26:59 +0000 (20:26 +0100)]
ucode: update to latest Git HEAD
e14b099 syntax: implement support for ES6 template literals 111cf06 vm: stop executing bytecode on return of nested calls 33f1e0b treewide: move json-c compat shims into internal header file e0e9431 vm: move unhandled exception reporting out of `uc_vm_execute_chunk()` 2b59140 vm: fix callframe double free on unhanded exceptions 7d7e950 main: abort when failing to load a preload library 1032a67 lib: let `json()` accept input objects implementing `read()` method 5ee68d5 fs: implement `fs.readfile()` and `fs.writefile()` df6b861 ci: debian: change path before attempting to invoke Git operations dfaf05a ci: debian: automatically update changelog from Git tag 34f3c45 ci: fix YAML syntax of Debian workflow e956bcf fs: fix off-by-one in fs.dirname() function 6fc4b6c .gitignore: fix overmatching patterns, blacklist cram .venv 7c2e082 build: remove legacy json-c check 77942af build: add polyfills for older libjson-c versions 0b4aaa3 CI: build Debian package f404285 debian: Add package definition a37f654 types: fix escape sequence encoding of high byte values in JSON strings aae5312 Update README.md 8134e25 build: fix symlink install target 87c7296 treewide: replace some leftover "utpl" occurrences, update .gitignore 7d27ad5 build: only stage ucc symlink if compile support is enabled 171402f lib: add date and time related functions 8b5dc60 lib: provide API function to obtain stdlib function implementations eb0d2f1 main: turn ucode into multicall executable 28ee7e1 uloop: add support for tasks 753dea9 CI: build on macOS 668c5c0 lib: add argument position support (`%m$`) to `sprintf()` and `printf()` ab46fdf treewide: remove legacy json-c include directives b8f49b1 tests: 21_regex_literals: generalize syntax error test case fd2e5e7 tests: 16_sort: fix logic flaw exposed on OS X 2c71bf2 tests: run_tests.sh: pass dummy value to `-T` flag 55c4a90 lib: disallow zero padding for %s formats 0d05cb5 tests: run_tests.sh: use greadlink if available 271e520 resolv: make OS X compatible d13c320 fs: avoid Linux specific sys/sysmacros.h include on OS X 33397a3 uloop: use execvp() on OS X bafdc8f lib: add naive sigtimedwait() stub for OS X ada1585 build: consolidate CMakeLists.txt and cover OS X deviations befbb69 include: add OS X compatible endian.h header 49838a8 include: rename include guards to avoid clashes with system headers 91f65de nl80211: add missing attributes and correct some attribute flags b4a1fd5 lib: adjust require(), render() and include() raw mode semantics 4618807 main: rework CLI frontend 73dcd78 lib: fix potential integer underflow on empty render output c402551 vm: fix crash on object literals with non-string computed properties efe8a02 syntax: support add new operators 078d686 ubus: add event support 6c66c83 ubus: refactor error and argument handling 1cb04f9 ubus: add object publishing, notify and subscribe support 0e85974 uloop: clear errno before integer conversion attempts 05bd7ed types: treat resource type prototypes as GC roots a2a26ca lib: introduce uloop binding 6b6d01f vm: release this context on exception in managed method call 1af23a9 tests: fix proto() testcase 4ce69a8 fs: implement access(), mkstemp(), file.flush() and proc.flush()
Daniel Golle [Tue, 19 Apr 2022 15:27:22 +0000 (16:27 +0100)]
uboot-mediatek: remove '0x' prefix from pstore node
Remove '0x' prefix from pstore node in dts, just like it was done
for the device tree used by Linux on MT7622.
This change is done in preparation to update U-Boot to 2022.04.
Daniel Golle [Tue, 19 Apr 2022 15:23:08 +0000 (16:23 +0100)]
mediatek: mt7622: remove '0x' prefix from pstore address in dts
Adresses of device tree nodes are typically noted without the '0x'
prefix. While having the '0x' prefix doesn't hurt when using Linux,
more recent versions of U-Boot will add a duplicate ramoops node as a
simple string compare is used to check if the node is already present.
Remove the '0x' prefix to avoid the kernel warning resulting from
U-Boot adding a dupplicate pstore/ramoops node.
See also https://lists.denx.de/pipermail/u-boot/2022-April/481810.html
projects / thirdparty / openwrt.git / log
