Espressobin Ultra has a front panel USB3.0 Type-A port which works
just fine so enable it.
I dont see a reason why it was disabled in the first place anyway.
Fixes: 3404fe15a60f ("arm64: dts: marvell: add DT for ESPRESSObin-Ultra") Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
SPI config for the SPI-NOR is incorrect and completely breaking
reading/writing to the onboard SPI-NOR.
SPI-NOR is connected in the single(x1) IO mode and not in the quad
(x4) mode.
Also, there is no need to override the max frequency from the DTSI
as the mx25u3235f that is used supports 104Mhz.
Fixes: 3404fe15a60f ("arm64: dts: marvell: add DT for ESPRESSObin-Ultra") Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
CMDQ may fail during HNS ROCEE initialization. The following is the log
when the execution fails:
hns3 0000:bd:00.2: In reset process RoCE client reinit.
hns3 0000:bd:00.2: CMDQ move tail from 840 to 839
hns3 0000:bd:00.2 hns_2: failed to set gid, ret = -11!
hns3 0000:bd:00.2: CMDQ move tail from 840 to 839
<...>
hns3 0000:bd:00.2: CMDQ move tail from 840 to 839
hns3 0000:bd:00.2: CMDQ move tail from 840 to 0
hns3 0000:bd:00.2: [cmd]token 14e mailbox 20 timeout.
hns3 0000:bd:00.2 hns_2: set HEM step 0 failed!
hns3 0000:bd:00.2 hns_2: set HEM address to HW failed!
hns3 0000:bd:00.2 hns_2: failed to alloc mtpt, ret = -16.
infiniband hns_2: Couldn't create ib_mad PD
infiniband hns_2: Couldn't open port 1
hns3 0000:bd:00.2: Reset done, RoCE client reinit finished.
However, even if ib_mad client registration failed, ib_register_device()
still returns success to the driver.
In the device initialization process, CMDQ execution fails because HW/FW
is abnormal. Therefore, if CMDQ fails, the initialization function should
set CMDQ to a fatal error state and return a failure to the caller.
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver") Link: https://lore.kernel.org/r/20220429093104.26687-1-liangwenpeng@huawei.com Signed-off-by: Yangyang Li <liyangyang20@huawei.com> Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Unlike on R-Car Gen3 SoCs, setting a bit to zero in a GPIO / Peripheral
Function Select Register (GPSRn) on R-Car V3U is not always sufficient
to configure a pin for GPIO. For I2C-capable pins, the I2C function
must also be explicitly disabled in the corresponding Module Select
Register (MODSELn).
Add the missing FN_SEL_I2Ci_0 function enums to the pinmux_data[] array
by temporarily overriding the GP_2_j_FN function enum to expand to two
enums: the original GP_2_j_FN enum to configure the GSPR register bits,
and the missing FN_SEL_I2Ci_0 enum to configure the MODSEL register
bits.
ep_poll() first calls ep_events_available() with no lock held and checks
if ep->rdllist is empty by list_empty_careful(), which reads
rdllist->prev. Thus all accesses to it need some protection to avoid
store/load-tearing.
Note INIT_LIST_HEAD_RCU() already has the annotation for both prev
and next.
Commit bf3b9f6372c4 ("epoll: Add busy poll support to epoll with socket
fds.") added the first lockless ep_events_available(), and commit c5a282e9635e ("fs/epoll: reduce the scope of wq lock in epoll_wait()")
made some ep_events_available() calls lockless and added single call under
a lock, finally commit e59d3c64cba6 ("epoll: eliminate unnecessary lock
for zero timeout") made the last ep_events_available() lockless.
BUG: KCSAN: data-race in do_epoll_wait / do_epoll_wait
write to 0xffff88810480c7d8 of 8 bytes by task 1802 on cpu 0:
INIT_LIST_HEAD include/linux/list.h:38 [inline]
list_splice_init include/linux/list.h:492 [inline]
ep_start_scan fs/eventpoll.c:622 [inline]
ep_send_events fs/eventpoll.c:1656 [inline]
ep_poll fs/eventpoll.c:1806 [inline]
do_epoll_wait+0x4eb/0xf40 fs/eventpoll.c:2234
do_epoll_pwait fs/eventpoll.c:2268 [inline]
__do_sys_epoll_pwait fs/eventpoll.c:2281 [inline]
__se_sys_epoll_pwait+0x12b/0x240 fs/eventpoll.c:2275
__x64_sys_epoll_pwait+0x74/0x80 fs/eventpoll.c:2275
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
read to 0xffff88810480c7d8 of 8 bytes by task 1799 on cpu 1:
list_empty_careful include/linux/list.h:329 [inline]
ep_events_available fs/eventpoll.c:381 [inline]
ep_poll fs/eventpoll.c:1797 [inline]
do_epoll_wait+0x279/0xf40 fs/eventpoll.c:2234
do_epoll_pwait fs/eventpoll.c:2268 [inline]
__do_sys_epoll_pwait fs/eventpoll.c:2281 [inline]
__se_sys_epoll_pwait+0x12b/0x240 fs/eventpoll.c:2275
__x64_sys_epoll_pwait+0x74/0x80 fs/eventpoll.c:2275
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
value changed: 0xffff88810480c7d0 -> 0xffff888103c15098
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 1799 Comm: syz-fuzzer Tainted: G W 5.17.0-rc7-syzkaller-dirty #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Link: https://lkml.kernel.org/r/20220322002653.33865-3-kuniyu@amazon.co.jp Fixes: e59d3c64cba6 ("epoll: eliminate unnecessary lock for zero timeout") Fixes: c5a282e9635e ("fs/epoll: reduce the scope of wq lock in epoll_wait()") Fixes: bf3b9f6372c4 ("epoll: Add busy poll support to epoll with socket fds.") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp> Reported-by: syzbot+bdd6e38a1ed5ee58d8bd@syzkaller.appspotmail.com Cc: Al Viro <viro@zeniv.linux.org.uk>, Andrew Morton <akpm@linux-foundation.org> Cc: Kuniyuki Iwashima <kuniyu@amazon.co.jp> Cc: Kuniyuki Iwashima <kuni1840@gmail.com> Cc: "Soheil Hassas Yeganeh" <soheil@google.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: "Sridhar Samudrala" <sridhar.samudrala@intel.com> Cc: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For avoiding kernel crash, this make sense for us. We only
concerned whether there has any non-system inode access before dlm
init. The answer is NO. And all journal replay/recovery handling
happen after dlm & journal init done. So this method is not graceful
but workable.
2> Add osb->journal check in free inode routine (eg ocfs2_clear_inode)
The fix code is special for mounting phase, but it will continue
working after mounting stage. In another word, this method adds
useless code in normal inode free flow.
3> Do directly free inode in mounting phase
This method is brutal/complex and may introduce unsafe code,
currently maintainer didn't like.
At last, we chose method <1> and did partly reverted job. We reverted
journal init codes, and kept cleanup codes flow.
Link: https://lkml.kernel.org/r/20220424130952.2436-1-heming.zhao@suse.com Link: https://lkml.kernel.org/r/20220424130952.2436-2-heming.zhao@suse.com Fixes: da5e7c87827e8 ("ocfs2: cleanup journal init and shutdown") Signed-off-by: Heming Zhao <heming.zhao@suse.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ffa core driver currently assigns its own driver information
to individual ffa device driver_data which is wrong. Firstly, it leaks
this core driver information to individual ffa_device and hence to
ffa_driver. Secondly the ffa_device driver_data is for use by individual
ffa_driver and not for this core driver managing all those devices.
While we pass uuid_null intentionally to ffa_partition_probe in
ffa_setup_partitions to get the count of the partitions, it must not be
uuid_null in ffa_partition_info_get which is used by the ffa_drivers
to fetch the specific partition info passing the UUID of the partition.
Fix ffa_partition_info_get by passing the received uuid down to
ffa_partition_probe so that the correct partition information is fetched.
__add_memory_block() calls both put_device() and device_unregister() when
storing the memory block into the xarray. This is incorrect because
xarray doesn't take an additional reference and device_unregister()
already calls put_device().
Triggering the issue looks really unlikely and its only effect should be
to log a spurious warning about a ref counted issue.
Link: https://lkml.kernel.org/r/d44c63d78affe844f020dc02ad6af29abc448fc4.1650611702.git.christophe.jaillet@wanadoo.fr Fixes: 4fb6eabf1037 ("drivers/base/memory.c: cache memory blocks in xarray to accelerate lookup") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Scott Cheloha <cheloha@linux.vnet.ibm.com> Cc: Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The flush_cache_page() only remove a PAGE_SIZE sized range from the cache.
However, it does not cover the full pages in a THP except a head page.
Replace it with flush_cache_range() to fix this issue. This is just a
documentation issue with the respect to properly documenting the expected
usage of cache flushing before modifying the pmd. However, in practice
this is not a problem due to the fact that DAX is not available on
architectures with virtually indexed caches per:
commit d92576f1167c ("dax: does not work correctly with virtual aliasing caches")
Link: https://lkml.kernel.org/r/20220403053957.10770-3-songmuchun@bytedance.com Fixes: f729c8c9b24f ("dax: wrprotect pmd_t in dax_mapping_entry_mkclean") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Dan Williams <dan.j.williams@intel.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Alistair Popple <apopple@nvidia.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hughd@google.com> Cc: Jan Kara <jack@suse.cz> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Ralph Campbell <rcampbell@nvidia.com> Cc: Ross Zwisler <zwisler@kernel.org> Cc: Xiongchun Duan <duanxiongchun@bytedance.com> Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn> Cc: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compaction sysfs file is created via compaction_register_node in
register_node. But we forgot to remove it in unregister_node. Thus
compaction sysfs file is leaked. Using compaction_unregister_node to fix
this issue.
Link: https://lkml.kernel.org/r/20220401070905.43679-1-linmiaohe@huawei.com Fixes: ed4a6d7f0676 ("mm: compaction: add /sys trigger for per-node memory compaction") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Rafael J. Wysocki <rafael@kernel.org> Cc: Mel Gorman <mel@csn.ul.ie> Cc: Minchan Kim <minchan.kim@gmail.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are 2 common cases when INIT_EX data file might not be
opened successfully and fail the sev initialization:
1. In user namespaces, normal user tasks (e.g. VMM) can change their
current->fs->root to point to arbitrary directories. While
init_ex_path is provided as a module param related to root file
system. Solution: use the root directory of init_task to avoid
accessing the wrong file.
2. Normal user tasks (e.g. VMM) don't have the privilege to access
the INIT_EX data file. Solution: open the file as root and
restore permissions immediately.
Fixes: 3d725965f836 ("crypto: ccp - Add SEV_INIT_EX support") Signed-off-by: Jacky Li <jackyli@google.com> Reviewed-by: Peter Gonda <pgonda@google.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not clear why the original implementation of overwrite support
required the dimm driver to be active before overwrite could proceed. In
fact that can lead to cases where the kernel retains an invalid cached
copy of the labels from before the overwrite. Unfortunately the kernel
has not only allowed that case, but enforced it.
Going forward, allow for overwrite to happen while the label area is
offline, and follow-on with updates to 'ndctl sanitize-dimm --overwrite'
to trigger the label area invalidation by default.
Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: Dave Jiang <dave.jiang@intel.com> Cc: Ira Weiny <ira.weiny@intel.com> Cc: Jeff Moyer <jmoyer@redhat.com> Reported-by: Krzysztof Kensicki <krzysztof.kensicki@intel.com> Fixes: 7d988097c546 ("acpi/nfit, libnvdimm/security: Add security DSM overwrite support") Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Lockdep reports the following deadlock scenarios for CXL root device
power-management, device_prepare(), operations, and device_shutdown()
operations for 'nd_region' devices:
These stem from holding nvdimm_bus_lock() over hibernate_quiet_exec()
which walks the entire system device topology taking device_lock() along
the way. The nvdimm_bus_lock() is protecting against unregistration,
multiple simultaneous ops callers, and preventing activate_show() from
racing activate_store(). For the first 2, the lock is redundant.
Unregistration already flushes all ops users, and sysfs already prevents
multiple threads to be active in an ops handler at the same time. For
the last userspace should already be waiting for its last
activate_store() to complete, and does not need activate_show() to flush
the write side, so this lock usage can be deleted in these attributes.
While enumerating protocols implemented by the SCMI platform using
BASE_DISCOVER_LIST_PROTOCOLS, the number of returned protocols is
currently validated in an improper way since the check employs a sum
between unsigned integers that could overflow and cause the check itself
to be silently bypassed if the returned value 'loop_num_ret' is big
enough.
Fix the validation avoiding the addition.
Link: https://lore.kernel.org/r/20220330150551.2573938-4-cristian.marussi@arm.com Fixes: b6f20ff8bd94 ("firmware: arm_scmi: add common infrastructure and support for base protocol") Signed-off-by: Cristian Marussi <cristian.marussi@arm.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
DMA channels requested by rz_ssi_dma_request() in rz_ssi_probe() were
never released in the error path apart from one place. This patch fixes
this issue by calling rz_ssi_release_dma_channels() in the error path.
Fixes: 26ac471c5354 ("ASoC: sh: rz-ssi: Add SSI DMAC support") Reported-by: Pavel Machek <pavel@denx.de> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20220426074922.13319-4-prabhakar.mahadev-lad.rj@bp.renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Propagate error codes returned from platform_get_irq_byname() instead of
returning -ENODEV. platform_get_irq_byname() may return -EPROBE_DEFER, to
handle such cases propagate the error codes.
While at it drop the dev_err_probe() messages as platform_get_irq_byname()
already does this for us in case of error.
We found that (at least some versions of) the sci-fw set the base clock
rate for UARTs in the MCU domain to 96 MHz instead of the expected 48 MHz,
leading to incorrect baud rates when used from Linux.
As the 8250_omap driver will query the actual clock rate from the clk
driver when clock-frequency is unset, removing the incorrect property is
sufficient to fix the baud rate.
As the potential failure of allocation, devm_kzalloc() may return NULL. Then
the 'pd->pmb' and the follow lines of code may bring null pointer dereference.
Therefore, it is better to check the return value of devm_kzalloc() to avoid
this confusion.
Fix the following Wstringop-overflow warnings when building with GCC-11:
drivers/scsi/fcoe/fcoe.c: In function ‘fcoe_netdev_config’:
drivers/scsi/fcoe/fcoe.c:744:32: warning: ‘fcoe_wwn_from_mac’ accessing 32 bytes in a region of size 6 [-Wstringop-overflow=]
744 | wwnn = fcoe_wwn_from_mac(ctlr->ctl_src_addr, 1, 0);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/fcoe/fcoe.c:744:32: note: referencing argument 1 of type ‘unsigned char *’
In file included from drivers/scsi/fcoe/fcoe.c:36:
./include/scsi/libfcoe.h:252:5: note: in a call to function ‘fcoe_wwn_from_mac’
252 | u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN], unsigned int, unsigned int);
| ^~~~~~~~~~~~~~~~~
drivers/scsi/fcoe/fcoe.c:747:32: warning: ‘fcoe_wwn_from_mac’ accessing 32 bytes in a region of size 6 [-Wstringop-overflow=]
747 | wwpn = fcoe_wwn_from_mac(ctlr->ctl_src_addr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
748 | 2, 0);
| ~~~~~
drivers/scsi/fcoe/fcoe.c:747:32: note: referencing argument 1 of type ‘unsigned char *’
In file included from drivers/scsi/fcoe/fcoe.c:36:
./include/scsi/libfcoe.h:252:5: note: in a call to function ‘fcoe_wwn_from_mac’
252 | u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN], unsigned int, unsigned int);
| ^~~~~~~~~~~~~~~~~
CC drivers/scsi/bnx2fc/bnx2fc_io.o
In function ‘bnx2fc_net_config’,
inlined from ‘bnx2fc_if_create’ at drivers/scsi/bnx2fc/bnx2fc_fcoe.c:1543:7:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:833:32: warning: ‘fcoe_wwn_from_mac’ accessing 32 bytes in a region of size 6 [-Wstringop-overflow=]
833 | wwnn = fcoe_wwn_from_mac(ctlr->ctl_src_addr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
834 | 1, 0);
| ~~~~~
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function ‘bnx2fc_if_create’:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:833:32: note: referencing argument 1 of type ‘unsigned char *’
In file included from drivers/scsi/bnx2fc/bnx2fc.h:53,
from drivers/scsi/bnx2fc/bnx2fc_fcoe.c:17:
./include/scsi/libfcoe.h:252:5: note: in a call to function ‘fcoe_wwn_from_mac’
252 | u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN], unsigned int, unsigned int);
| ^~~~~~~~~~~~~~~~~
In function ‘bnx2fc_net_config’,
inlined from ‘bnx2fc_if_create’ at drivers/scsi/bnx2fc/bnx2fc_fcoe.c:1543:7:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:839:32: warning: ‘fcoe_wwn_from_mac’ accessing 32 bytes in a region of size 6 [-Wstringop-overflow=]
839 | wwpn = fcoe_wwn_from_mac(ctlr->ctl_src_addr,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
840 | 2, 0);
| ~~~~~
drivers/scsi/bnx2fc/bnx2fc_fcoe.c: In function ‘bnx2fc_if_create’:
drivers/scsi/bnx2fc/bnx2fc_fcoe.c:839:32: note: referencing argument 1 of type ‘unsigned char *’
In file included from drivers/scsi/bnx2fc/bnx2fc.h:53,
from drivers/scsi/bnx2fc/bnx2fc_fcoe.c:17:
./include/scsi/libfcoe.h:252:5: note: in a call to function ‘fcoe_wwn_from_mac’
252 | u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN], unsigned int, unsigned int);
| ^~~~~~~~~~~~~~~~~
drivers/scsi/qedf/qedf_main.c: In function ‘__qedf_probe’:
drivers/scsi/qedf/qedf_main.c:3520:30: warning: ‘fcoe_wwn_from_mac’ accessing 32 bytes in a region of size 6 [-Wstringop-overflow=]
3520 | qedf->wwnn = fcoe_wwn_from_mac(qedf->mac, 1, 0);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qedf/qedf_main.c:3520:30: note: referencing argument 1 of type ‘unsigned char *’
In file included from drivers/scsi/qedf/qedf.h:9,
from drivers/scsi/qedf/qedf_main.c:23:
./include/scsi/libfcoe.h:252:5: note: in a call to function ‘fcoe_wwn_from_mac’
252 | u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN], unsigned int, unsigned int);
| ^~~~~~~~~~~~~~~~~
drivers/scsi/qedf/qedf_main.c:3521:30: warning: ‘fcoe_wwn_from_mac’ accessing 32 bytes in a region of size 6 [-Wstringop-overflow=]
3521 | qedf->wwpn = fcoe_wwn_from_mac(qedf->mac, 2, 0);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/scsi/qedf/qedf_main.c:3521:30: note: referencing argument 1 of type ‘unsigned char *’
In file included from drivers/scsi/qedf/qedf.h:9,
from drivers/scsi/qedf/qedf_main.c:23:
./include/scsi/libfcoe.h:252:5: note: in a call to function ‘fcoe_wwn_from_mac’
252 | u64 fcoe_wwn_from_mac(unsigned char mac[MAX_ADDR_LEN], unsigned int, unsigned int);
| ^~~~~~~~~~~~~~~~~
by changing the array size to the correct value of ETH_ALEN in the
argument declaration.
Also, fix a couple of checkpatch warnings:
WARNING: function definition argument 'unsigned int' should also have an identifier name
This helps with the ongoing efforts to globally enable
-Wstringop-overflow.
Link: https://github.com/KSPP/linux/issues/181 Fixes: 85b4aa4926a5 ("[SCSI] fcoe: Fibre Channel over Ethernet") Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Boot memory area is setup as separate PT_LOAD segment in the vmcore
as it is moved by f/w, on crash, to a destination address provided by
the kernel. Having separate PT_LOAD segment helps in handling the
different physical address and offset for boot memory area in the
vmcore.
Commit ced1bf52f477 ("powerpc/fadump: merge adjacent memory ranges to
reduce PT_LOAD segements") inadvertly broke this pre-condition for
cases where some of the first kernel memory is available adjacent to
boot memory area. This scenario is rare but possible when memory for
fadump could not be reserved adjacent to boot memory area owing to
memory hole or such. Reading memory from a vmcore exported in such
scenario provides incorrect data. Fix it by ensuring no other region
is folded into boot memory area.
Fixes: ced1bf52f477 ("powerpc/fadump: merge adjacent memory ranges to reduce PT_LOAD segements") Signed-off-by: Hari Bathini <hbathini@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220406093839.206608-2-hbathini@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
vmbus_request_addr() returns 0 (zero) if the transaction ID passed
to as argument is 0. This is unfortunate for two reasons: first,
netvsc_send_completion() does not check for a NULL cmd_rqst (before
dereferencing the corresponding NVSP message); second, 0 is a *valid*
value of cmd_rqst in netvsc_send_tx_complete(), cf. the call of
vmbus_sendpacket() in netvsc_send_pkt().
vmbus_request_addr() has included the code in question since its
introduction with commit e8b7db38449ac ("Drivers: hv: vmbus: Add
vmbus_requestor data structure for VMBus hardening"); such code was
motivated by the early use of vmbus_requestor by hv_storvsc. Since
hv_storvsc moved to a tag-based mechanism to generate and retrieve
transaction IDs with commit bf5fd8cae3c8f ("scsi: storvsc: Use
blk_mq_unique_tag() to generate requestIDs"), vmbus_request_addr()
can be modified to return VMBUS_RQST_ERROR if the ID is 0. This
change solves the issues in hv_netvsc (and makes the handling of
messages with transaction ID of 0 consistent with the semantics
"the ID is not contained in the requestor/invalid ID").
vmbus_next_request_id(), vmbus_request_addr() should still reserve
the ID of 0 for Hyper-V, because Hyper-V will "ignore" (not respond
to) VMBUS_DATA_PACKET_FLAG_COMPLETION_REQUESTED packets/requests with
transaction ID of 0 from the guest.
Fixes: bf5fd8cae3c8f ("scsi: storvsc: Use blk_mq_unique_tag() to generate requestIDs") Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20220419122325.10078-2-parri.andrea@gmail.com Signed-off-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This chip has an armv7 arch timer according to the dts. Select it in
Kconfig to enforce the support for it.
Otherwise the system time is just completely wrong if user forget to
enable ARM_ARCH_TIMER in kernel config.
simple_ondemand interacts poorly with clamp_to_idle. It only looks at
the load since the last get_dev_status call, while it should really look
at the load over polling_ms. When clamp_to_idle true, it almost always
picks the lowest frequency on active because the gpu is idle between
msm_devfreq_idle/msm_devfreq_active.
This logic could potentially be moved into devfreq core.
Fixes: 7c0ffcd40b16 ("drm/msm/gpu: Respect PM QoS constraints") Signed-off-by: Chia-I Wu <olvaffe@gmail.com> Cc: Rob Clark <robdclark@chromium.org> Link: https://lore.kernel.org/r/20220416003314.59211-3-olvaffe@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit c8013355ead6 ("ARM: dts: gpio-ranges property is now required")
fixed the GPIO probing issues caused by "pinctrl: bcm2835: Change init
order for gpio hogs". This changed only the kernel DTS files. Unfortunately
it isn't guaranteed that these files are shipped to all users.
So implement the necessary backward compatibility for BCM2835 and
BCM2711 platform.
Since commit 2ab73c6d8323 ("gpio: Support GPIO controllers without pin-ranges")
the device tree nodes of GPIO controller need the gpio-ranges property to
handle gpio-hogs. Unfortunately it's impossible to guarantee that every new
kernel is shipped with an updated device tree binary.
In order to provide backward compatibility with those older DTB, we need a
callback within of_gpiochip_add_pin_range() so the relevant platform driver
can handle this case.
This function assumes that sizeof(void) is 1 and arithmetic works for
void pointers. This is a GNU C extention and may not work with other
compilers. Change this by using an u8 pointer.
Also move cn10k_read_trng() out of a loop thus saving some cycles.
Fixes: 38e9791a0209 ("hwrng: cn10k - Add random number generator support") Signed-off-by: Vladis Dronov <vdronov@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
info_release() will be called in device_unregister() when info->dev's
reference count is 0. So there is no need to call ocxl_afu_put() and
kfree() again.
Fix this by adding free_minor() and return to err_unregister error path.
Fixes: 75ca758adbaf ("ocxl: Create a clear delineation between ocxl backend & frontend") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Acked-by: Frederic Barrat <fbarrat@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20220418085758.38145-1-hbh25y@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Per KSZ9031RNX PHY datasheet FIGURE 7-5: POWER-UP/POWER-DOWN/RESET TIMING
Note 2: After the de-assertion of reset, wait a minimum of 100 μs before
starting programming on the MIIM (MDC/MDIO) interface.
Add 1ms post-reset delay to guarantee this figure.
Fixes: 010ca9fe500bf ("ARM: dts: stm32: Add missing ethernet PHY reset on AV96") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 413dda8f2c6f ("platform/chrome: cros_ec_chardev: Use
cros_ec_cmd_xfer_status helper") inadvertendly changed the userspace ABI.
Previously, cros_ec ioctls would only report errors if the EC communication
failed, and otherwise return success and the result of the EC
communication. An EC command execution failure was reported in the EC
response field. The above mentioned commit changed this behavior, and the
ioctl itself would fail. This breaks userspace commands trying to analyze
the EC command execution error since the actual EC command response is no
longer reported to userspace.
Fix the problem by re-introducing the cros_ec_cmd_xfer() helper, and use it
to handle ioctl messages.
Fixes: 413dda8f2c6f ("platform/chrome: cros_ec_chardev: Use cros_ec_cmd_xfer_status helper") Cc: Daisuke Nojiri <dnojiri@chromium.org> Cc: Rob Barnes <robbarnes@google.com> Cc: Rajat Jain <rajatja@google.com> Cc: Brian Norris <briannorris@chromium.org> Cc: Parth Malkan <parthmalkan@google.com> Reviewed-by: Daisuke Nojiri <dnojiri@chromium.org> Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The capability detection logic clears bits for the features that are
disabled in a certain SKU. For example, if the bit associate to
compression is not present in the LEGFUSE register, the correspondent
bit is cleared in the capability mask.
This change adds the compression capability to the mask as this was
missing in the commit that enhanced the capability detection logic.
Fixes: cfe4894eccdc ("crypto: qat - set COMPRESSION capability for QAT GEN2") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Marco Chiappero <marco.chiappero@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Set the CIPHER capability for QAT DH895XCC devices if the hardware supports
it. This is done if both the CIPHER and the AUTHENTICATION engines are
available on the device.
Fixes: ad1332aa67ec ("crypto: qat - add support for capability detection") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Signed-off-by: Marco Chiappero <marco.chiappero@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clear the IDT vectoring field in vmcs12 on next VM-Exit due to a double
or triple fault. Per the SDM, a VM-Exit isn't considered to occur during
event delivery if the exit is due to an intercepted double fault or a
triple fault. Opportunistically move the default clearing (no event
"pending") into the helper so that it's more obvious that KVM does indeed
handle this case.
Note, the double fault case is worded rather wierdly in the SDM:
The original event results in a double-fault exception that causes the
VM exit directly.
Temporarily ignoring injected events, double faults can _only_ occur if
an exception occurs while attempting to deliver a different exception,
i.e. there's _always_ an original event. And for injected double fault,
while there's no original event, injected events are never subject to
interception.
Presumably the SDM is calling out that a the vectoring info will be valid
if a different exit occurs after a double fault, e.g. if a #PF occurs and
is intercepted while vectoring #DF, then the vectoring info will show the
double fault. In other words, the clause can simply be read as:
The VM exit is caused by a double-fault exception.
Fixes: 4704d0befb07 ("KVM: nVMX: Exiting from L2 to L1") Cc: Chenyi Qiang <chenyi.qiang@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220407002315.78092-4-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't modify vmcs12 exit fields except EXIT_REASON and EXIT_QUALIFICATION
when performing a nested VM-Exit due to failed VM-Entry. Per the SDM,
only the two aformentioned fields are filled and "All other VM-exit
information fields are unmodified".
Fixes: 4704d0befb07 ("KVM: nVMX: Exiting from L2 to L1") Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220407002315.78092-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit f3e7dae323ab ("ARM: dts: imx6qdl: add enet_out clk
support") added another item to the list of clocks for the fec
device. As imx6dl-eckelmann-ci4x10.dts only overwrites clocks,
but not clock-names this resulted in an inconsistency with
clocks having one item more than clock-names.
Also overwrite clock-names with the same value as in
imx6qdl.dtsi. This is a no-op today, but prevents similar
inconsistencies if the soc file will be changed in a similar way
in the future.
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Link: https://lore.kernel.org/r/20220309091953.5630-1-linmq006@gmail.com Fixes: 87e8657ba99c ("PCI: mediatek: Add new method to get shared pcie-cfg base address") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Miles Chen <miles.chen@mediatek.com> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The F1C100 series of SoCs actually have their watchdog IP being
compatible with the newer Allwinner generation, not the older one.
The currently described sun4i-a10-wdt actually does not work, neither
the watchdog functionality (just never fires), nor the reset part
(reboot hangs).
Replace the compatible string with the one used by the newer generation.
Verified to work with both the watchdog and reboot functionality on a
LicheePi Nano.
Also add the missing interrupt line and clock source, to make it binding
compliant.
This fixes:
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: cru-bus@100: 'pin-controller@1c0' does not match any of the regexes: '^clock-controller@[a-f0-9]+$', '^phy@[a-f0-9]+$', '^pinctrl@[a-f0-9]+$', '^syscon@[a-f0-9]+$', '^thermal@[a-f0-9]+$'
From schema: Documentation/devicetree/bindings/mfd/brcm,cru.yaml
arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dtb: pin-controller@1c0: $nodename:0: 'pin-controller@1c0' does not match '^(pinctrl|pinmux)(@[0-9a-f]+)?$'
From schema: Documentation/devicetree/bindings/pinctrl/brcm,ns-pinmux.yaml
'dmc->counter' is a 'struct devfreq_event_dev **', so there is some
over memory allocation. 'counters_size' should be computed with
'sizeof(struct devfreq_event_dev *)'.
Use 'sizeof(*dmc->counter)' instead to fix it.
While at it, use devm_kcalloc() instead of devm_kzalloc()+open coded
multiplication.
acpi_pci_bridge_d3(dev) returns "true" if "dev" is a hotplug bridge that
can handle hotplug events while in D3. Previously this meant either:
- "dev" has a _PS0 or _PR0 method (acpi_pci_power_manageable()), or
- The Root Port above "dev" has a _DSD with a "HotPlugSupportInD3"
property with value 1.
This did not consider _PRW, which tells us about wakeup GPEs (ACPI v6.4,
sec 7.3.13). Without a wakeup GPE, from an ACPI perspective the Root Port
has no way of generating wakeup signals, so hotplug events will be lost if
we use D3.
Similarly, it did not consider _S0W, which tells us the deepest D-state
from which a device can wake itself (sec 7.3.20). If _S0W tells us the
device cannot wake from D3, hotplug events will again be lost if we use D3.
Some platforms, e.g., AMD Yellow Carp, supply "HotPlugSupportInD3" without
_PRW or with an _S0W that says the Root Port cannot wake from D3. On those
platforms, we previously put bridges in D3hot, hotplug events were lost,
and hotplugged devices would not be recognized without manually rescanning.
Allow bridges to be put in D3 only if the Root Port can generate wakeup
GPEs (wakeup.flags.valid), it can wake from D3 (_S0W), AND it has the
"HotPlugSupportInD3" property.
Neither Windows 10 nor Windows 11 puts the bridge in D3 when the firmware
is configured this way, and this change aligns the handling of the
situation to be the same.
The handling of connection failures shall be handled by the request
completion callback as already done by hci_cs_le_create_conn, also make
sure to use hci_conn_failed instead of hci_le_conn_failed as the later
don't actually call hci_conn_del to cleanup.
This attempts to cleanup the hci_conn if it cannot be aborted as
otherwise it would likely result in having the controller and host
stack out of sync with respect to connection handle.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The original x86 sev_alloc() only called set_memory_decrypted() on
memory returned by alloc_pages_node(), so the page order calculation
fell out of that logic. However, the common dma-direct code has several
potential allocators, not all of which are guaranteed to round up the
underlying allocation to a power-of-two size, so carrying over that
calculation for the encryption/decryption size was a mistake. Fix it by
rounding to a *number* of pages, rather than an order.
Until recently there was an even worse interaction with DMA_DIRECT_REMAP
where we could have ended up decrypting part of the next adjacent
vmalloc area, only averted by no architecture actually supporting both
configs at once. Don't ask how I found that one out...
Fixes: c10f07aa27da ("dma/direct: Handle force decryption for DMA coherent buffers in common code") Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the process of checking whether RDMAv2 is available, the current
implementation first sets ini->smcrv2.ib_dev_v2, and then allocates
smc buf desc, but the latter may fail. Unfortunately, the caller
will only check the former. In this case, a NULL pointer reference
will occur in smc_clc_send_confirm_accept() when accessing
conn->rmb_desc.
This patch does two things:
1. Use the return code to determine whether V2 is available.
2. If the return code is NODEV, continue to check whether V1 is
available.
Fixes: e49300a6bf62 ("net/smc: add listen processing for SMC-Rv2") Signed-off-by: liuyacan <liuyacan@corp.netease.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Same trigger condition as commit 86434744. When setsockopt runs
in parallel to a connect(), and switch the socket into fallback
mode. Then the sk_refcnt is incremented in smc_connect(), but
its state stay in SMC_INIT (NOT SMC_ACTIVE). This cause the
corresponding sk_refcnt decrement in __smc_release() will not be
performed.
Fixes: 86434744fedf ("net/smc: add fallback check to connect()") Signed-off-by: liuyacan <liuyacan@corp.netease.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since kconfig 'select' does not follow dependency chains, if symbol KSA
selects KSB, then KSA should also depend on the same symbols that KSB
depends on, in order to prevent Kconfig warnings and possible build
errors.
Change NET_DSA_SMSC_LAN9303_I2C and NET_DSA_SMSC_LAN9303_MDIO so that
they are limited to VLAN_8021Q if the latter is enabled. This prevents
the Kconfig warning:
WARNING: unmet direct dependencies detected for NET_DSA_SMSC_LAN9303
Depends on [m]: NETDEVICES [=y] && NET_DSA [=y] && (VLAN_8021Q [=m] || VLAN_8021Q [=m]=n)
Selected by [y]:
- NET_DSA_SMSC_LAN9303_I2C [=y] && NETDEVICES [=y] && NET_DSA [=y] && I2C [=y]
Fixes: 430065e26719 ("net: dsa: lan9303: add VLAN IDs to master device") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Vivien Didelot <vivien.didelot@gmail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Vladimir Oltean <olteanv@gmail.com> Cc: Juergen Borleis <jbe@pengutronix.de> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Mans Rullgard <mans@mansr.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the decision on when to generate an IDLE ACK by keeping a count of the
number of packets we've received, but not yet soft-ACK'd, and the number of
packets we've processed, but not yet hard-ACK'd, rather than trying to keep
track of which DATA sequence numbers correspond to those points.
We then generate an ACK when either counter exceeds 2. The counters are
both cleared when we transcribe the information into any sort of ACK packet
for transmission. IDLE and DELAY ACKs are skipped if both counters are 0
(ie. no change).
Fixes: 805b21b929e2 ("rxrpc: Send an ACK after every few DATA packets we receive") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previousPacket field in the rx ACK packet should never go backwards -
it's now the highest DATA sequence number received, not the last on
received (it used to be used for out of sequence detection).
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix accidental overlapping of Rx-phase ACK accounting with Tx-phase ACK
accounting through variables shared between the two. call->acks_* members
refer to ACKs received in the Tx phase and call->ackr_* members to ACKs
sent/to be sent during the Rx phase.
Fixes: 1a2391c30c0b ("rxrpc: Fix detection of out of order acks") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
rxrpc has a timer to trigger resending of unacked data packets in a call.
This is not cancelled when a client call switches to the receive phase on
the basis that most calls don't last long enough for it to ever expire.
However, if it *does* expire after we've started to receive the reply, we
shouldn't then go into trying to retransmit or pinging the server to find
out if an ack got lost.
Fix this by skipping the resend code if we're into receiving the reply to a
client call.
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
AF_RXRPC's listen() handler lets you set the backlog up to 32 (if you bump
up the sysctl), but whilst the preallocation circular buffers have 32 slots
in them, one of them has to be a dead slot because we're using CIRC_CNT().
This means that listen(rxrpc_sock, 32) will cause an oops when the socket
is closed because rxrpc_service_prealloc_one() allocated one too many calls
and rxrpc_discard_prealloc() won't then be able to get rid of them because
it'll think the ring is empty. rxrpc_release_calls_on_socket() then tries
to abort them, but oopses because call->peer isn't yet set.
Fix this by setting the maximum backlog to RXRPC_BACKLOG_MAX - 1 to match
the ring capacity.
Fixes: 00e907127e6f ("rxrpc: Preallocate peers, conns and calls for incoming service requests") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org Link: https://lists.infradead.org/pipermail/linux-afs/2022-March/005079.html Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's a locking issue with the per-netns list of calls in rxrpc. The
pieces of code that add and remove a call from the list use write_lock()
and the calls procfile uses read_lock() to access it. However, the timer
callback function may trigger a removal by trying to queue a call for
processing and finding that it's already queued - at which point it has a
spare refcount that it has to do something with. Unfortunately, if it puts
the call and this reduces the refcount to 0, the call will be removed from
the list. Unfortunately, since the _bh variants of the locking functions
aren't used, this can deadlock.
================================
WARNING: inconsistent lock state
5.18.0-rc3-build4+ #10 Not tainted
--------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
ksoftirqd/2/25 [HC0[0]:SC1[1]:HE1:SE0] takes: ffff888107ac4038 (&rxnet->call_lock){+.?.}-{2:2}, at: rxrpc_put_call+0x103/0x14b
{SOFTIRQ-ON-W} state was registered at:
...
Possible unsafe locking scenario:
1 lock held by ksoftirqd/2/25:
#0: ffff8881008ffdb0 ((&call->timer)){+.-.}-{0:0}, at: call_timer_fn+0x5/0x23d
Changes
=======
ver #2)
- Changed to using list_next_rcu() rather than rcu_dereference() directly.
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure that the support of PEC is determined before the read of other
registers. Otherwise the validation of PEC can trigger an error on the read
of STATUS_BYTE or STATUS_WORD registers.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without the move of the code, at the second load of
the driver (or bind) the STATUS_BYTE or STATUS_WORD register is always
read with PEC enabled, which is likely to cause a read error resulting
with fail of a driver load (or bind).
When a gateway receives an advertisement message, it extracts relay
information and then it should be freed.
But the advertisement handler doesn't free it.
So, memory leak would occur.
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a gateway can not receive any response to requests from a relay,
gateway resets status from SENT_REQUEST to INIT and variable about a
relay as well. And then it should start the full establish step
from sending a discovery message and receiving advertisement message.
But, after failure in amt_req_work() it continues sending a request
message step with flushed(invalid) relay information and sets SENT_REQUEST.
So, a gateway can't be established with a relay.
In order to avoid this situation, it stops sending the request message
step if it fails.
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The evsel->name may have a different format for a topdown event, a pure
topdown name (e.g., topdown-fe-bound), or a PMU name + a topdown name
(e.g., cpu/topdown-fe-bound/). The cpu/topdown-fe-bound/ kind format
isn't supported by the arch_evlist__leader(). This format is a very
common format for a hybrid platform, which requires specifying the PMU
name for each event.
Without the patch,
$ perf stat -e '{instructions,slots,cpu/topdown-fe-bound/}' -a sleep 1
Some events weren't counted. Try disabling the NMI watchdog:
echo 0 > /proc/sys/kernel/nmi_watchdog
perf stat ...
echo 1 > /proc/sys/kernel/nmi_watchdog
The events in group usually have to be from the same PMU. Try reorganizing the group.
With the patch,
$ perf stat -e '{instructions,slots,cpu/topdown-fe-bound/}' -a sleep 1
Validation of signed input should be done before casting to unsigned int.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Suggested-by: Mark Brown <broonie@kernel.org> Fixes: 2fbe467bcbfc ("ASoC: max98090: Reject invalid values in custom control put()") Link: https://lore.kernel.org/r/1652999486-29653-1-git-send-email-khoroshilov@ispras.ru Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing the rcu_read_lock in bond_ethtool_get_ts_info() as
discussed [1], I didn't notice it could be called via setsockopt,
which doesn't hold rcu lock, as syzbot pointed:
Fix it by adding rcu_read_lock and take a ref on the real_dev.
Since dev_hold() and dev_put() can take NULL these days, we can
skip checking if real_dev exist.
Reported-by: syzbot+92beb3d46aab498710fa@syzkaller.appspotmail.com Fixes: aa6034678e87 ("bonding: use rcu_dereference_rtnl when get bonding active slave") Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220519020148.1058344-1-liuhangbin@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are sleep in atomic context bugs when the request to secure
element of st21nfca is timeout. The root cause is that kzalloc and
alloc_skb with GFP_KERNEL parameter and mutex_lock are called in
st21nfca_se_wt_timeout which is a timer handler. The call tree shows
the execution paths that could lead to bugs:
This patch moves the operations that may sleep into a work item.
The work item will run in another kernel thread which is in
process context to execute the bottom half of the interrupt.
So it could prevent atomic context from sleeping.
Fixes: 2130fb97fecf ("NFC: st21nfca: Adding support for secure element") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220518115733.62111-1-duoming@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Removing an ATA device via sysfs means that the device may not be found
through re-scanning:
root@ubuntu:/home/john# lsscsi
[0:0:0:0] disk SanDisk LT0200MO P404 /dev/sda
[0:0:1:0] disk ATA HGST HUS724040AL A8B0 /dev/sdb
[0:0:8:0] enclosu 12G SAS Expander RevB -
root@ubuntu:/home/john# echo 1 > /sys/block/sdb/device/delete
root@ubuntu:/home/john# echo "- - -" > /sys/class/scsi_host/host0/scan
root@ubuntu:/home/john# lsscsi
[0:0:0:0] disk SanDisk LT0200MO P404 /dev/sda
[0:0:8:0] enclosu 12G SAS Expander RevB -
root@ubuntu:/home/john#
The problem is that the rescan of the device may conflict with the device
in being re-initialized, as follows:
- In the rescan we call hisi_sas_slave_alloc() in store_scan() ->
sas_user_scan() -> [__]scsi_scan_target() -> scsi_probe_and_add_lunc()
-> scsi_alloc_sdev() -> hisi_sas_slave_alloc() -> hisi_sas_init_device()
In hisi_sas_init_device() we issue an IT nexus reset for ATA devices
- That IT nexus causes the remote PHY to go down and this triggers a bcast
event
- In parallel libsas processes the bcast event, finds that the phy is down
and marks the device as gone
The hard reset issued in hisi_sas_init_device() is unncessary - as
described in the code comment - so remove it. Also set dev status as
HISI_SAS_DEV_NORMAL as the hisi_sas_init_device() call.
Link: https://lore.kernel.org/r/1652354134-171343-4-git-send-email-john.garry@huawei.com Fixes: 36c6b7613ef1 ("scsi: hisi_sas: Initialise devices in .slave_alloc callback") Tested-by: Yihang Li <liyihang6@hisilicon.com> Reviewed-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
PTP one step sync packets cannot have CSUM padding and insertion in
SW since time stamp is inserted on the fly by HW.
In addition, ptp4l version 3.0 and above report an error when skb
timestamps are reported for packets that not processed for TX TS
after transmission.
Add a helper to identify PTP one step sync and fix the above two
errors. Add a common mask for PTP header flag field "twoStepflag".
Also reset ptp OSS bit when one step is not selected.
In the genpd governor we walk the list of child-domains to take into
account their next_wakeup. If the child-domain itself, doesn't have a
governor assigned to it, we can end up using the next_wakeup value before
it has been properly initialized. To prevent a possible incorrect behaviour
in the governor, let's initialize next_wakeup to KTIME_MAX.
Fixes: c79aa080fb0f ("PM: domains: use device's next wakeup to determine domain idle state") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The code in bfq_check_waker() ignores wake up events from the current
waker. This makes it more likely we select a new tentative waker
although the current one is generating more wake up events. Treat
current waker the same way as any other process and allow it to reset
the waker detection logic.
Fixes: 71217df39dc6 ("block, bfq: make waker-queue detection more robust") Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220519105235.31397-2-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we look for waker only if current queue has no requests. This
makes sense for bfq queues with a single process however for shared
queues when there is a larger number of processes the condition that
queue has no requests is difficult to meet because often at least one
process has some request in flight although all the others are waiting
for the waker to do the work and this harms throughput. Relax the "no
queued request for bfq queue" condition to "the current task has no
queued requests yet". For this, we also need to start tracking number of
requests in flight for each task.
This patch (together with the following one) restores the performance
for dbench with 128 clients that regressed with commit c65e6fd460b4
("bfq: Do not let waker requests skip proper accounting") because
this commit makes requests of wakers properly enter BFQ queues and thus
these queues become ineligible for the old waker detection logic.
Dbench results:
Numbers are time to complete workload so lower is better.
Fixes: c65e6fd460b4 ("bfq: Do not let waker requests skip proper accounting") Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20220519105235.31397-1-jack@suse.cz Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
of_find_node_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: e20db70dba1c ("thermal: imx_sc: add i.MX system controller thermal support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220517055121.18092-1-linmq006@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
