Weijie Gao [Sun, 18 Nov 2018 15:49:23 +0000 (23:49 +0800)]
ramips: merge two patches 101-mt7621-timer and 998-mt7621-needs-jiffies
These two patches both modified the mt7621.c, and the patch file
998-mt7621-needs-jiffies.patch adds only one line which is used by the
another patch file. So merge them into one file.
sdk: expose part of advanced configuration options
These option can be useful in developement/packagig applications for
OpenWrt. Instead of searching them by hand in Config-build.in lets
expose them for easier access.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Steven Honson [Fri, 7 Sep 2018 13:44:19 +0000 (13:44 +0000)]
kernel: nf-nathelper-extra depends on ipt-raw
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
As automatic helper assignment is disabled in recent Linux kernels,
explicit rules must be added to the raw table for each helper.
While commit f50a524 in the firewall3 project added a set of default
rules and other additional related functionality, both this and the
alternative manual methods of defining these rules require kmod-ipt-raw.
Signed-off-by: Steven Honson <steven@honson.id.au>
apm821xx: add support for the Netgear WNDAP620 and WNDAP660
This patch adds support for the Netgear WNDAP620 and WNDAP660,
they are similar devices, but due to the LAN LED configuration,
the switch setup and WIFI configuration each gets a different
device target.
Hardware Highlights WNDAP620:
CPU: AMCC PowerPC APM82181 at 1000 MHz
DRAM: 128 MB, 2 x 64 MiB DDR2 Hynix H5PS5162GF
CPU: AMCC PowerPC APM82181 at 1000 MHz
FLASH: 32 MiB, NAND SLC, Hynix HY27US08561A
Ethernet: RealTek RTL8363SB 2x2-Port Switch PHY - Only 1 GBit Port (POE)
Wifi: Atheros AR9380 minipcie - Dual-Band - 3x3:3
Serial: console port with RJ45 Interface (9600-N-8-1)
LEDS: Power, LAN-Activity, dual color LAN-Linkspeed, 2.4GHz, 5GHz LEDs
Button: Soft Reset Button
Antennae: 3 internal dual-band antennae + 3 x RSMA for external antennaes
- needs a tftp server at 192.168.1.10/serverip.
- special 8P8C(aka RJ45)<->D-SUB9 Console Cable
("Cisco Console Cable"). Note: Both WNDAP6x0 have
a MAX3232 transceivers, hence no need for any separate
CMOS/TTL level shifters.
External Antenna:
The antennae mux is controlled by GPIO 11 and GPIO14. Valid Configurations:
= Config# = | = GPIO 11 = | = GPIO 14 = | ===== Description =====
1. | 1 / High | 0 / Low | Use the internal antennae (default)
2. | 0 / Low | 1 / High | Use the external antennae
The external antennaes are only meant for the 2.4 GHz band.
One-way Flashing instructions via u-boot:
0. connect the serial cable to the RJ45 Console Port
Note: This requires a poper RS232 and not a TTL/USB adaptor.
1. power up the AP and interrupt the u-boot process at
'Hit any key to stop autoboot'
2. setup serverip and ipaddr env settings
Enter the following commands into the u-boot shell
# setenv ipaddr 192.168.1.1
# setenv serverip 192.168.1.10
3. download the factory.img image to the AP
Enter the following commands into the u-boot shell
generic: rtl836x: support defered probe on mdio-bus
On the WNDAP620, the mdio and mdc lines are controlled by
the EMAC ethernet device. This results in a hen-vs-egg problem.
The rtl8367b driver is probed before the ethernet driver and
the mdio-bus is not available yet, which caused the rtl8367b
driver to fail.
This patch changes the rtl8366_smi_probe_of() function to
return -EPROBE_DEFER if the mdio-bus lookup failed and changes
rtl8366_smi_probe()'s signature to return the error code back to
the callee, so it can propagate back to the kernel. Which, will
retry the switch probe at a later time.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds u-boot environment access to the MX60(W) target.
"The environment size is one NAND block (128KiB on Buckminster).
We allocate four NAND blocks to deal with bad blocks which may
exist in the saved environment"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
All apm821xx devices use u-boot and most of them have
an accessible u-boot environment. This patch adds the
necessary template file, but does not add the
uboot-envtools package to any of the targets.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specification:
- SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU
- RAM: 512MB DDR3 System Memory
- NOR Flash: 32MB SPI NOR
- NAND Flash: 256MB NAND
- Ethernet: 5 x 1G via QCA8337N
- USB: 2 x USB 3.0 SuperSpeed
- PCIe: 3x Mini PCIe 2.0 Slots
Three PCIE2.0 connectors can connect two or three radio cards
such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN
How to flash via u-boot console:
tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin
nand erase 0x1340000 0x4000000
nand write 0x44000000 0x1340000 $filesize
setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’
saveenv
bootm
Further upgrades via sysupgrade.
Tested on IPQ8064 AP161 Board:
1) NAND boot
2) Tested USB and PCIe interfaces
3) WDOG test
4) cpu frequency scaling
5) ethernet, 2G and 5G WiFi
6) ubi sysupgrade
Sergey Ryazanov [Thu, 25 Oct 2018 22:22:37 +0000 (01:22 +0300)]
ar71xx: fix RouterBOARD Power LED default state
RouterBOARD(s) bootloader actully turns Power LED off just before
it starts the kernel. So we need to set the LED default status to On
instead of Keep in order to keep LED on during kernel boot.
This change fixes Power LED off during the kernel boot on the RB91x and
SXT Lite boards.
Fixes: 6cad8ee0bd ("ar71xx: keep the RouterBOARD Power LED in On state") CC: Mathias Kresin <dev@kresin.me> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Create initrd enries for x86 images, that'll load amd microcode as early
as possible. Also remove the preinit script responsible for late load of
microcode.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Via TFTP:
Rename factory image to "tp_recovery.bin" and place it in the root-dir
of your tftp server. Configure to listen on 192.168.0.66. Power up the
router while holding down the reset-button. The router will flash itself
and reboot.
Note: For TFTP, you might need a switch between router and computer, as
link establishment might take to long.
Daniel Santos [Mon, 5 Nov 2018 02:48:13 +0000 (20:48 -0600)]
ralink: Add support for GPIO as interrupt-controller
The gpio-ralink driver has everything it needs to be used as an
interrupt controller except for device tree support. This simple patch
adds that support by configuring the irq domain to use two cells and
adding the appropriate documentation to the devicetree bindings.
Signed-off-by: Daniel Santos <daniel.santos@pobox.com>
Petr Štetiar [Tue, 13 Nov 2018 12:10:40 +0000 (13:10 +0100)]
ramips: Add support for ZTE ZXECS EBG3130 aka BDCOM WAP2100-SK
On the bottom sticker it's branded as ZTE ZXECS EBG3130 device, but in factory
OpenWrt image it's referenced as BDCOM WAP2100-SK device.
Specifications:
- SoC: MediaTek MT7620A
- RAM: 128 MB
- Flash: 16 MB
- Ethernet: 5 FE ports
- Wireless radio: 2T2R 2.4 GHz and 1T1R 5 GHz (MT7610EN, unsupported)
- UART: 1 x UART on PCB marked as J2 (R=RX, T=TX, G=GND) with 115200 8N1 config
- LEDs: Power, FE ports 1-5, WPS, USB, RF 2.4G, RF 5G
- Other: USB port, SD card slot and 2x external antennas (non-detachable)
Flashing instructions:
A) The U-Boot has HTTP based firmware upgrade
A1) Flashing notes
We've identified so far two different batches of units, unfortunately
each batch has different U-Boot bootloader flashed with different
default environment variables, thus each batch has different IP address
for accessing web based firmware updater.
* First batch has web based bootloader IP address 1.1.1.1
* Second batch has web based bootloader IP address 192.168.1.250
In case you can't connect to either of those IPs, you can try to get
the default IP address via two methods:
A1.1) Serial console, then the IP address is visible during the boot
...
HTTP server is starting at IP: 1.1.1.1
raspi_read: from:40004 len:6
HTTP server is ready!
...
* Change IP address of PC to 1.1.1.2 with 255.255.255.0 netmask
* Reboot the device and try to reach web based bootloader in the
browser with the following URL http://1.1.1.1
* Quickly select the firmware sysupgrade file and click on the
`Update firmware` button, this all has to be done within 10 seconds,
bootloader doesn't wait any longer
If done correctly, the web page should show UPDATE IN PROGRESS page
with progress indicator. Once the flashing completes (it takes roughly
around 1 minute), the device will reboot to the OpenWrt firmware
B) The U-boot is based on Ralink SDK so we can flash the firmware using UART.
1. Configure PC with a static IP address and setup an TFTP server.
2. Put the firmware into the tftp directory.
3. Connect the UART line as described on the PCB (G=GND, R=RX, T=TX)
4. Power up the device and press 2, follow the instruction to set device and
tftp server IP address and input the firmware file name. U-boot will then load
the firmware and write it into the flash.
Create initrd enries for x86 images, that'll load intel microcode as
early as possible. To achieve that the test module for grub is enabled
which provides shell-like conditionals. Also restrict the late load of
microcode to AMD processors.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Currently every file in boot directory is copied over target /boot on
root file system and is usually inaccessible because appropriate boot
file system is mounted on top of it. Therefore remove /boot, which in
result will also save space on target root file system.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Petr Štetiar [Mon, 19 Nov 2018 20:44:50 +0000 (21:44 +0100)]
ath79: ubnt-m-xw: Fix factory image flashing using TFTP recovery method
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions
A) Serial console, U-Boot and TFTP
1. Connect to serial header J1 on the PCB
2. Power on device and enter U-Boot console
3. Set up TFTP server serving an OpenWrt initramfs build
4. Load initramfs build using the command tftpboot in the U-Boot cli
5. Boot the loaded image using the command bootm
6. Copy squashfs OpenWrt sysupgrade build to the booted device
7. Use mtd to write sysupgrade to partition "firmware"
8. Reboot and enjoy
B) Experimental factory image flashing over SSH from airOS v6.1.7
1. You need to flash your UBNT M2HP with airOS v6.1.7 firmware
no other airOS version is currently supported
2. git clone https://github.com/true-systems/ubnt-bullet-m2hp-openwrt-flashing
3. cd ubnt-bullet-m2hp-openwrt-flashing
4. make flash-factory FW_OWRT=/path/to/your/openwrt-ath79-generic-ubnt_bullet-m-xw-squashfs-factory.bin
Belkin F5D8235 v2 has two ethernet switches on board.
One internal rt3052 and rtl8366rb on rgmii interface.
Looks like internal switch settings were lost in
translation to device tree infrastructure.
Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board
Flash instruction:
>From Skylab firmware:
1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
sysupgrade image, apply, flash will fail with a message:
Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
Unlocking mtd4 ...
Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.
>From U-boot via TFTP and initramfs:
1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
with sysupgrade.
>From U-boot via TFTP direct flash:
1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
Input device IP (10.10.10.123) ==:192.168.11.21
Input server IP (10.10.10.3) ==:192.168.11.20
Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
port 0 (WAN).
Signed-off-by: Russell Senior <russell@personaltelco.net>
Petr Štetiar [Fri, 23 Nov 2018 09:53:37 +0000 (10:53 +0100)]
build: Introduce building of artifacts
We currently could (ab)use IMAGES for this task, but the downside is,
that the filenames has filesystem tied to the filename, which might be
confusing as the artifact itself don't has to be used with that specific
filesystem. Another downside is, that the artifacts built with IMAGES
target are build for every FILESYSTEMS filesystem.
Hans Dedecker [Sun, 25 Nov 2018 19:17:52 +0000 (20:17 +0100)]
nghttp2: bump to 1.35.0
e520469b Update manual pages 54067256 Bump up version number to 1.35.0 c4d2eeee Update AUTHORS f51e696e asio: Add stop() to listen_and_serve doc a433b132 Merge pull request #1260 from nghttp2/h2load-non-final-response cf48a56d Merge pull request #1238 from jktjkt/cmake-fix-libevent-detection 6cad1b24 nghttpx: Write mruby send_info early 3c393dca nghttpx: Fix assertion failure on mruby send_info with HTTP/1 frontend 17292445 h2load: Handle HTTP/1 non-final response f6644a92 make clang-format 48998f72 Merge pull request #1222 from donny-dont/fix/declspec 15ff52f9 Update README 6c03bb14 Upgrade travis toolchain 524b4392 Fix travis build failure 859bf2bc Update manual pages b5619fb1 h2load: Clarify that time for connect includes TLS handshake dcbe0c69 nghttpx: Simplify move ctor and operator 2996c284 nghttpx: Cleanup 42e8ceb6 nghttpx: Convert API status code to enum class 1daf9ce8 nghttpx: Convert WorkerEventType to enum class d68edf56 nghttpx: Convert MemcachedStatusCode to enum class 0c4e9fef nghttpx: Convert memcached op to enum class 571404c6 nghttpx: Convert MemcachedParseState to enum class 4d562b77 nghttpx: Convert LogFragmentType to enum class e6225871 nghttpx: Convert connection check status to enum class 4bd075de nghttpx: Convert Http2Session state to enum class b46a3249 nghttpx: Convert FreelistZone to enum class 4bd44b9c nghttpx: Convert dispatch state to enum class 1b42110d nghttpx: Make Downstream state enum class 0735ec55 nghttpx: Convert shrpx_connect_proto to enum class 00554779 nghttpx: Convert DNSResolverStatus to enum class 0963f389 nghttpx: Convert SerialEventType to enum class 1abfa3ca nghttpx: Make TLS handshake state enum class f2159bc2 nghttpx: Convert UpstreamAltMode to enum class b0eb68ee nghttpx: Convert shrpx_forwarded_node_type to enum class e7b7b037 nghttpx: Convert shrpx_cookie_secure to enum class 5e4f434f nghttpx: Convert shrpx_session_affinity to enum class 20ea964f nghttpx: Convert shrpx_proto to enum class d105619b src: Remove extra braces if possible ec5729b1 Use std::make_unique 6c919695 Use C++14 46576178 Don't send Transfer-Encoding to pre-HTTP/1.1 clients 5e925f87 Update doc 153531d4 nghttpx: Use the same type as standard stream operator<< f7287df0 Bump up version number to 1.35.0-DEV
Rosen Penev [Tue, 13 Nov 2018 20:59:47 +0000 (12:59 -0800)]
flex: Add a lex symlink
Some packages like libpfring assume the presense of lex, which on some
other systems is a symlink to flex but not all. Symlink flex to fix
compilation.
This is probably theoretical problem as the Ventana is defined first in
the image Makefile, but once the position of the definition would change
in the future (alphabetical sorting?) it would get bootscript from the
previous board which would have BOOT_SCRIPT set.
Cc: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Sun, 25 Nov 2018 13:35:49 +0000 (14:35 +0100)]
ramips: select kmod-mt76x0e for TP-Link ArcherC20i and wr902ac-v3
Both devices come with a MediaTek MT7610E 5GHz 802.11ac 1T1R radio
which wasn't supported at the time the devices were added to OpenWrt.
Now that we got it, include kmod-mt76x0e in images for those devices.
Reported-by: Arian Sanusi <openwrt@semioptimal.net> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 15 Nov 2018 16:12:54 +0000 (11:12 -0500)]
kernel: enable CONFIG_BRIDGE_VLAN_FILTERING
This allows us to use the bridge as a managed switch and gracefully
handle mixed tagged and untagged frames. Prior to this, the only
alternative was creating one bridge per vlan which quickly becomes a
nightmare and still won't let you mix both tagged and untagged frames on
the physical port without some complex ebtables magic.
This is in line with the notion that OpenWRT is the network go-to swiss
army knife when you need a nice set-and-forget, low maintenance box to
handle a specific task.
Current builds of the ip-bridge package already fully support this
feature so the only requirement is enabling the kernel config.
This is disabled by default so existing bridge configurations will not
be affected. This patch only gives the ability to turn it on with an
'ip link' command. If there is interest, I could look into making the
feature accessible via uci configuration.
It causes about 3.1% hit on raw bridging speed, which is relatively
trivial considering that I had to use 300 byte packets to strain the CPU
enough to notice a slowdown at all. The ER8 would chug along at wire
speed otherwise, and that's using only one core. Since the typical
bridge use case on OpenWRT is wireless, I doubt it would be noticeable
at all.
With BRIDGE_VLAN_FILTERING
iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.1.12 port 58045 connected with 192.168.1.105 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec
[ 3] Sent 3414986 datagrams
[ 3] Server Report:
[ 3] 0.0-10.0 sec 811 MBytes 680 Mbits/sec 0.000 ms
581210/3414986 (0%)
Without BRIDGE_VLAN_FILTERING
iperf -u -c 192.168.1.105 -b 1G -l 300
------------------------------------------------------------
Client connecting to 192.168.1.105, UDP port 5001
Sending 300 byte datagrams, IPG target: 2.24 us (kalman adjust)
UDP buffer size: 208 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.1.12 port 36645 connected with 192.168.1.105 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 977 MBytes 820 Mbits/sec
[ 3] Sent 3414990 datagrams
[ 3] Server Report:
[ 3] 0.0-10.0 sec 836 MBytes 701 Mbits/sec 0.000 ms
493950/3414990 (0%)
In terms of kernel size, it uses 16KB (6753K vs 6737K on ER8) so a
0.002% hit. The exact 16KB is probably just due to how the kernel is
compressed.
Suggested-by: Jonathan Thibault <jonathan@navigue.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hannu Nyman [Sat, 24 Nov 2018 11:58:37 +0000 (13:58 +0200)]
ath79: specify "firmware" partition format for WNDR3700 and v2
Specify the new "firmware" partition format for Netgear WNDR3700
and WNDR3700v2 similarly as ffd082aa did for WNDR3800, the third
device in the family.
Rafał Miłecki [Thu, 22 Nov 2018 11:55:14 +0000 (12:55 +0100)]
kernel: don't auto-split "firmware" if it has "compatible" DT property
If "compatible" is being used that should trigger a proper parser
directly. It's more reliable thanks to not trying parsers one by one. In
such case partition shouldn't be split automatically to avoid parsing it
twice.
David Bauer [Mon, 22 Oct 2018 00:35:36 +0000 (02:35 +0200)]
kernel: b53: register switch on probe
Currently, the b53 MDIO switch driver registers the switch on
config-init and not on device probe. Because of this, the switch
gets added every time the associated interface comes up.
This commit fixes this behavior by registering the switch on device
probe.
Linus Kardell [Thu, 22 Nov 2018 10:35:08 +0000 (11:35 +0100)]
base-files: fix unkillable processes after restart
When restart is run on an init script, the script traps SIGTERM. This is
done as a workaround for scripts named the same name as the program they
start. In that case, the init script process will have the same name as
the program process, and so when the init script runs killall, it will
kill itself. So SIGTERM is trapped to make the init script unkillable.
However, the trap is retained when the init script runs start, and thus
processes started by restart will not respond to SIGTERM, and will thus
be unkillable unless you use SIGKILL. This fixes that by removing the
trap before running start.
Rafał Miłecki [Thu, 22 Nov 2018 09:12:19 +0000 (10:12 +0100)]
bcm53xx: request Seama parser on DIR-885L directly
It's more reliable as mtd subsystem doesn't have to blindly try that
parser. It allows disabling MTD_SPLIT_FIRMWARE completely (TRX is
handled in a similar way).
Hans Dedecker [Wed, 21 Nov 2018 10:11:26 +0000 (11:11 +0100)]
glibc: update to latest 2.27 commit
1517dfb8aa Add an additional test to resolv/tst-resolv-network.c 1050634904 libanl: properly cleanup if first helper thread creation failed (bug 22927)
Felix Fietkau [Wed, 21 Nov 2018 14:14:36 +0000 (15:14 +0100)]
mt76: update to the latest version
4734108 mt7603: use mt7603_wtbl_clear on station removal 9428e34 mt7603: fix watchdog reset sequence b3f82a3 mt7603: report PSE reset failures via debugfs a301dec mt7603: add back PSE client reset code 94cebfc mt7603: fix handling lost interrupt events during watchdog reset b38fe7d mt7603: only issue PSE reset on PSE stuck da666a7 mt7603: issue PSE reset if firmware debug register indicates stuck queues
* chacha20,poly1305: fix up for win64
* poly1305: only export neon symbols when in use
* poly1305: cleanup leftover debugging changes
* crypto: resolve target prefix on buggy kernels
* chacha20,poly1305: don't do compiler testing in generator and remove xor helper
* crypto: better path resolution and more specific generated .S
* poly1305: make frame pointers for auxiliary calls
* chacha20,poly1305: do not use xlate
This should fix up the various build errors, warnings, and insertion errors
introduced by the previous snapshot, where we added some significant
refactoring. In short, we're trying to port to using Andy Polyakov's original
perlasm files, and this means quite a lot of work to re-do that had stableized
in our old .S.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Hans Dedecker [Mon, 19 Nov 2018 09:12:28 +0000 (10:12 +0100)]
netifd: update to latest git HEAD
4b83102 treewide: switch to C-code style comments 70506bf treewide: make some functions static d9872db interface: fix removal of dynamic interfaces 2f7ef7d interface: rework code to get rid of interface_set_dynamic
Felix Fietkau [Fri, 16 Nov 2018 11:43:45 +0000 (12:43 +0100)]
mt76: update to the latest version
009ab91 mt76: clean up more unused EXPORT_SYMBOLs 963768d mt76x02: fix regression in tx station race condition fix d7788cc mt76: mt76x02: make group_wcid the first member in struct mt76x02_vif e65ad4c mt7603: make group_wcid the first member in struct mt7603_vif 7b1373e mt76: mt76x02: remove mt76x02_txq_init a97127b mt76: replace sta_add/remove ops with common sta_state function 13f1e82 mt7603: clear wtbl entry for removed stations 90e2c1b mt7603: add mt7603_wtbl_set_skip_tx, change mt7603_wtbl_set_ps users 41931e4 mt7603: toggle skip_tx on station add/remove d0fdf01 mt7603: avoid unnecessary wtbl writes for ps-filter
* Zinc no longer ships generated assembly code. Rather, we now
bundle in the original perlasm generator for it. The primary purpose
of this snapshot is to get testing of this.
* Clarify the peer removal logic and make lifetimes more precise.
* Use READ_ONCE for is_valid and is_dead.
* No need to use atomic when the recounter is mutex protected.
* Fix up macros and annotations in allowedips.
* Increment drop counter when staged packets are dropped.
* Use static constants instead of enums for 64-bit values in selftest.
* Mark large constants as ULL in poly1305-donna64.
* Fix sparse warnings in allowedips debugging code.
* Do not use wg_peer_get_maybe_zero in timer callbacks, since we now can
carefully control the lifetime of these functions and ensure they never
execute after dropping the last reference.
* Cleanup hashing in ratelimiter.
* Do not guard timer removals, since del_timer is always okay.
* We now check for PM_AUTOSLEEP, which makes the clear*on-suspend decision a
bit more general.
* Set csum_level to ~0, since the poly1305 authenticator certainly means
that no data was modified in transit.
* Use CHECKSUM_PARTIAL check for skb_checksum_help instead of
skb_checksum_setup check.
* wg.8: specify that wg(8) shows runtime info too
* wg.8: AllowedIPs isn't actually required
* keygen-html: add missing glue macro
* wg-quick: android: do not choke on empty allowed-ips
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Rafał Miłecki [Thu, 15 Nov 2018 11:28:50 +0000 (12:28 +0100)]
kernel: fix ubifs loosing O_TMPFILE data after power cut
There was a bug in ubifs related to the O_TMPFILE. When reapplying
changes after power cut data could be lost. This problem was exposed by
overlayfs and the upstream commit 3a1e819b4e80 ("ovl: store file handle
of lower inode on copy up").
This fixes a regression introduced when switching from 4.9 to 4.14.
Hans Dedecker [Thu, 15 Nov 2018 10:29:04 +0000 (11:29 +0100)]
bison: update to 3.2.1
Chnages since 3.2:
b590ad02 version 3.2.1 05e70adf build: fix issues in the generated tarball 7efe0b5d build: fix typo 351e3630 NEWS: update 4fd1fc70 examples: ship them e02ce4c7 build: minor fixes in doc/ 7cab285e CI: maximize chances of errors sooner 86efe282 c++: improve the generated documentation cf1446dc tests: don't fail if the C++ compiler does not work e93c40b3 tests: don't disable C++ warnings in C files eff67391 c++: workaround portability issue 5a0d7802 tests: work around getopt portability issues f1e0839c doc: -Wzero-as-null-pointer-constant was added to GCC 4.7 3bf429ae examples: #include <cstring> in calc++ f8cadc73 c: provide a definition of _Noreturn that works for C++ bd7aebb8 c: update the definition of _Noreturn ca8039e6 tests: don't expect the shell to support 'local' 5d07f4f7 bitset: fix warning e605ad96 build: fix use of gnulib Make variables 50fac71d maint: post-release administrivia
projects / thirdparty / openwrt.git / log
