Thibaut VARENE [Thu, 23 Feb 2017 11:24:05 +0000 (12:24 +0100)]
ar71xx: mikrotik: erase firmware partition on SPI NOR devices in pre_upgrade()
On Mikrotik SPI NOR devices, the firmware partition must be erased when flashing
from stock firmware, otherwise leftover bits (in particular a kernel signature)
can trigger a boot loop.
When booted from initramfs (the only way to flash LEDE on these devices),
this patch unconditionally erases the firmware partition in the pre_upgrade()
stage for all supported SPI NOR devices.
Felix Fietkau [Sat, 25 Feb 2017 10:15:07 +0000 (11:15 +0100)]
ubus: update to the latest version
c09e4f0 ubusd: fix incomplete copy of shared buf during queue-ing 453b87f cli: add support for subscribing to objects 6eb3c96 cli: do not use default timeout for listen dfe3383 libubus: reset ctx->sock.error when doing ubus reconnect 34c6e81 cli: fix listen_timeout compile issue
Yousong Zhou [Fri, 3 Feb 2017 13:15:42 +0000 (21:15 +0800)]
mac80211: hwsim: select DRIVER_11AC_SUPPORT and DRIVER_11W_SUPPORT
This is required for default wireless configuration of malta target to
work out of the box again. Fixes "77ece30e: hostapd: Add ability to
specify that that wireless driver supports 802.11ac"
Ben Kelly [Mon, 20 Feb 2017 12:04:30 +0000 (14:04 +0200)]
swconfig: Bugfix switch_port uci option parsing
When not defining 'device' or 'vlan' in relevant switch_port uci
sections, behaviour is inconsistent due to *devn, *port and *vlan
pointers not being zero initialized.
Joseph C. Lehner [Sun, 19 Feb 2017 12:13:15 +0000 (13:13 +0100)]
mt76: split kmod package
This patch splits `kmod-mt76` into three separate packages:
`kmod-mt76-core`, `kmod-mt76x2` and `kmod-mt7603`. By making
`kmod-mt76` a metapackage containing these new packages,
the previous behaviour of including all drivers and firmware
is left unchanged, unless explicitly unselected in
`DEVICE_PACKAGES`.
This splitting is especially beneficial for devices with
small flash chips, since the `kmod-mt76` package currently
requires ~160K on squashfs (after compression).
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
Felix Fietkau [Wed, 22 Feb 2017 12:31:17 +0000 (13:31 +0100)]
lantiq: fix broadcast packets leaking on the wrong vlan on xrx200
The ethernet driver uses a port map override via special tag to control
the ports on which multicast packets are sent. This was added to work
around an issue in the switch that was occasionally leaking packets onto
the wrong vlan.
Unfortunately the change had some leftover lines that were overwrting
the port map with a list of all ports, thus always leaking packets onto
the wront vlan.
Fix this by only enabling the override with the VLAN port map and only
if a matching VLAN port map was actually found
The @ sign in front of the "mv" command was significantly suppressing
output to stdout. When reviewing the make/build logs it was tricking
me a whole lot and it mad me lose time. Removing the @ sign will get
stdout and logs right about what happened when.
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Thibaut VARENE [Wed, 15 Feb 2017 10:40:06 +0000 (11:40 +0100)]
ar71xx: Enable mtdsplit support for RB SPI NOR devices
This patch enables mtdsplit for the MikroTik subtarget.
It converts mach-rbspi.c to use a single "firmware" partition.
Finally, it converts the SPI NOR profile to metadata images:
the original combined-image format is gone, the images are now
"standard" sysupgrade images with metadata appended.
Note: kernel2minor apparently pads the kernel container to erase-block
boundary, but this is undocumented behaviour, so we do not rely on it
and call pad-to anyway.
Note: in platform.sh, the boards are tested last in platform_check_image()
as this should eventually become the "*)" default case when more devices
switch to metadata images.
Thibaut VARENE [Tue, 14 Feb 2017 13:42:10 +0000 (14:42 +0100)]
kernel: mtdsplit: Add support for Mikrotik NOR firmware
The RouterBOOT bootloader does not care where the kernel lives in the SPI
flash, all that matters is that the kernel is wrapped in the custom yaffs
container as generated by kernel2minor.
This container has a fixed signature as follows: 00000000 00 00 00 01 00 00 00 01 ff ff 6b 65 72 6e 65 6c |..........kernel|
This patch adds mtdsplit support for identifying that signature and
triggering the search for the rootfs. rootfs is expected at EB boundary since
we use wget mtd_find_rootfs_from(). We make no use of the yaffs file size
field because it contains invalid data in the image generated by kernel2minor.
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.
Fixes: FS#542 Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
Alif M. Ahmad [Mon, 20 Feb 2017 18:58:20 +0000 (01:58 +0700)]
x86_64: Add support for EFI framebuffer (FS#515)
CONFIG_FB_EFI and CONFIG_FB_SIMPLE are needed to display console text on
EFI framebuffer.
CONFIG_FB_EFI is needed when the kernel is directly launched via EFI
shell or EFI startup.nsh script.
CONFIG_FB_SIMPLE is needed when launching the kernel via grub2 efi. In
this case, grub2 has prepared a gfxterm framebuffer and the kernel just
need to use the already prepared grub's gfxterm framebuffer to display
console text.
Signed-off-by: Alif M. Ahmad <alive4ever@live.com>
Felix Fietkau [Tue, 21 Feb 2017 13:24:32 +0000 (14:24 +0100)]
px5g: replace px5g-standalone with a statically linked variant of px5g-mbedtls
px5g-standalone only supports SHA1 for certificates, which is strongly
deprecated. The new px5g-standalone is about 27k bigger (compressed),
and has identical behavior to px5g-mbedtls (it uses SHA256).
Felix Fietkau [Mon, 20 Feb 2017 11:13:51 +0000 (12:13 +0100)]
cmake: skip build system check on compile
cmake checks the build system and its variables on its own to detect if
the makefiles need to be regenerated.
Unfortunately this can invalidate overrides passed in the
Build/Configure step. On non-Linux systems this breaks the build when
switching between targets of the same package architecture.
Fix this by forcibly disabling the build system check and relying on the
LEDE build system to take care of these things
Michal Sojka [Thu, 16 Feb 2017 22:02:50 +0000 (23:02 +0100)]
scripts/feeds: Reuse TOPDIR if defined in environment
The feeds script sets value of TOPDIR in a way that is inconsistent
with how toplevel Makefile sets it. The inconsistency manifests when I
use a "build directory" with symlinks to LEDE source (see below).
When make is invoked in such a directory, make's TOPDIR variable is
set to that directory, whereas scripts/feeds sets TOPDIR to the top of
LEDE source, which results in creating feeds directory inside the LEDE
source instead of in the build directory.
This patch changes the script so that it reuses the TOPDIR value form
the environment if it exists. The result is that 'make
package/symlinks' correctly fetches feeds to the build directory
instead in the source.
I use the following commands to create the build directory:
This commit causes opkg to install px5g-standalone instead of px5g when
installing luci-ssl. As luci-ssl depends on mbedtls, using
px5g-standalone makes no sense. Next to that, it creates deprecated SHA1
certificates. Revert the commit to avoid pxg5-standalone to be
installed by accident.
Weijie Gao [Sat, 18 Feb 2017 14:32:49 +0000 (22:32 +0800)]
ar71xx: fix vlan settings for some boards
For AR71XX devices, GMAC1 always connects port 0 of the built-in switch,
as the CPU port.
This patch sets correct vlan for some devices with wrong settings:
a) mark port 0 as CPU port, tagged
b) reverse port order, marking these ports untagged
Specifying USE_PRIVATE_LIBGCC is no longer needed, as it is the
default.
Patch 001 is removed, since it was already merged upstream. Patches
100 and 101 are removed because they do not appear to be needed
anymore, and they do not conform with the sign-off and commit message
procedures.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Because they were hidden, there was no way to disable the uboot
targets in menuconfig, so they had to be built every time. The omap
target is the only one to hide uboot packages. To be consistent with
the other targets, and have more control over the build, un-hide the
u-boot packages.
Note that the default behavior remains unchanged, as uboot will be
built unless explicitly disabled.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Thomas Roberts [Mon, 13 Feb 2017 17:29:34 +0000 (17:29 +0000)]
ar71xx: add support for TL-WR802N Version 2
This patch adds support for the TP-Link TL-WR802N Version 2.
Specification:
- SoC: Qualcomm Atheros QCA9533 (560 MHz, MIPS 24Kc)
- RAM: 32 MiB
- Storage: 4 MiB of FLash on board
- Wireless: Built into QCA9533 (Honey Bee), PHY modes b/g/n
- Ethernet: 1x100M (port0)
Installation through OEM Web Interface:
- Connect to TL-WR802N by Ethernet or Wi-Fi
- Go to http://192.168.0.1 (default user is "admin" & password is "admin)
- Go to "System Tools -> Firmware Upgrade"
- Browse for firmware "*.factory-us.bin" or "*.factory-eu.bin" for eu model
- Click upgrade
Installation through tftp:
Note: T_OUT, T_IN and GND on the board must be connected to USB TTL
Serial Configuration 115200 8n1
- Boot the TL-WR802N
- When "Autobooting in 1 seconds" appears type "tpl" followed by enter
- Connect to the board Ethernet port
(IPADDR: 192.168.1.1, ServerIP: 192.168.1.10)
- tftpboot 0x80000000 <Firmware Image Name>
- Record the result of "printenv bootcmd"
- Enter "erase <Result of 'printenv bootcmd'> +0x3c0000"
(e.g erase 0x9f020000 +0x3c0000)
- Enter "cp.b 0x80000000 <Result of 'printenv bootcmd'> 0x3c0000"
(e.g cp.b 0x80000000 0x9f020000 0x3c0000)
- Enter "bootm <Result of 'printenv bootcmd'>"
(e.g bootm 0x9f020000)
Signed-off-by: Thomas Roberts <tom.p.roberts@gmail.com>
Mathias Kresin [Fri, 17 Feb 2017 21:16:01 +0000 (22:16 +0100)]
lantiq: set the internet led interface according to wan interface
Use the nas0 interface for the netdev trigger as default. Use the ptm0
interface for xRX200 boards to match the default wan interface set in
02_network.
David Woodhouse [Wed, 15 Feb 2017 17:27:45 +0000 (17:27 +0000)]
x86: Set default baud rate on Geode images to 115200
Prior to commit 1496b95a0 ("x86: clean up default grub baudrate
settings") we had three different baud rates for the Geode targets:
19200 for net5501, 38400 for alix2, and 115200 for Geos.
It doesn't seem that there's a very good reason for varying from our
default 115200 baud, so let's make the Geode target do that instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
David Woodhouse [Wed, 15 Feb 2017 16:11:12 +0000 (16:11 +0000)]
x86: Add Geos profile for Geode subtarget
This makes the Geode images actually useful again. The Geos profile
should include the relevant hardware for that board, and the Default
profile adds the via-rhine adapter which seems to have been present in
the net5501 and alix targets killed in commit 9e0759ea265 ("x86: merge
all geode based subtargets into one").
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Karol Dudek [Sun, 12 Feb 2017 17:34:36 +0000 (18:34 +0100)]
ar71xx: add support for 8devices Lima board
Lima is a module for the (IoE) internet of everything applications,
based on Qualcomm/Atheros QCA4531.
Specification:
- 650/600/216 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 32 MB of FLASH
- 2T2R 2.4 GHz
- 2x 10/100 Mbps Ethernet
- USB 2.0 Host
- PCIe
- UART for serial console
- 14x GPIO
Flash instruction:
1. Download lede-ar71xx-generic-lima-squashfs-sysupgrade.bin
and rename it to 8dev_recovery.bin
2. Binary file copy to USB stick and plug into slot USB
3. Press S2 (reset) button
4. Press and hold the S1 button by 5 seconds
5. Wait ~40 seconds to complete recovery
Günther Kelleter [Wed, 15 Feb 2017 09:36:49 +0000 (10:36 +0100)]
ar8216: flush ARL table during reset after init_globals
commit 33b72b8e0faf7a39faabece584fd6da61cd8f8df
"ar8216: adjust ATU flushing in case of link changes"
introduced portwise flushing on link down events. Now the ARL table could
be in a chaotic state after boot where ar8xxx_sw_get_arl_table looped
forever (depending on the entries collected while booting).
Furong Xu [Thu, 16 Feb 2017 02:00:48 +0000 (10:00 +0800)]
ramips: fix PWM pin mux conflict in dtsi
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict
[ 0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[ 0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[ 0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux
[ 0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back
Removing redundant spaces from the name of the option. Without fix:
root@LEDE:~# opkg install ugps
Installing ugps (2016-10-24-32a6b2b7-1) to root...
Downloading http://downloads.lede-project.org/releases/17.01-SNAPSHOT/packages/mips_24kc/base/ugps_2016-10-24-32a6b2b7-1_mips_24kc.ipk
Configuring ugps.
uci: Parse error (invalid character in name field) at line 3, byte 23
uci: Parse error (invalid character in name field) at line 3, byte 23
sh: out of range
root@LEDE:~# uci show gps
uci: Parse error (invalid character in name field) at line 3, byte 23
With this fix:
root@LEDE:~# uci show gps
gps.@gps[0]=gps
gps.@gps[0].tty='ttyACM0'
gps.@gps[0].adjust_time='1'
Felix Fietkau [Thu, 16 Feb 2017 06:43:27 +0000 (07:43 +0100)]
build: fix the toolchain rebuild check
- Check for changes in toolchain/ only
- Only replace the stamp file if it was changed
- Fix dependencies for staging dir prepare
- Move the stamp file to TOOLCHAIN_DIR
Mirko Parthey [Tue, 14 Feb 2017 14:05:09 +0000 (15:05 +0100)]
brcm47xx: fix USB driver choice for Asus WL-500W
BCM4704 SoC has only USB 1.1 core:
ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
but this device actually comes with two USB 2.0 ports.
It appears embedded controller isn't used but instead there are two PCI
attached controllers (next to the BCM4321 wireless card):
1106:3038 VT82xx/62xx UHCI USB 1.1 Controller
1106:3104 USB 2.0
Choose a set of USB drivers which actually support this hardware.
Felix Fietkau [Wed, 15 Feb 2017 11:33:03 +0000 (12:33 +0100)]
kernel: fix crashes on MIPS when loading kernel modules under memory pressure
When memory is tight, modules may need to be loaded into vmalloc()
space. The code then has to generate jump trampolines which enable
relocations between vmalloc space and physical address space.
The code had a bug that was freeing these trampolines even when the
module was successfully loaded.
Rafał Miłecki [Wed, 15 Feb 2017 10:46:57 +0000 (11:46 +0100)]
mdns: update and rename package to the umdns
This update includes numerous small fixes for:
1) Interfaces setup
2) Packets parsing
3) Sending replies
Without this there were multiple problems with exchanging information
between (u)mdns and other implementations (including (u)mdns as well).
This also follows project rename to umdns which was required to avoid
confusion with Apple's mdnsd from mDNSResponder project.
Thibaut VARENE [Fri, 10 Feb 2017 19:36:50 +0000 (20:36 +0100)]
ar71xx: add preliminary kernel support for several RB SPI NOR devices
The cAP 2nD, mAP 2nD and wAP 2nD apparently all share the same QCA953x/SPI-NOR
platform.
This patch adds preliminary kernel support based on init data used in
Mikrotik's linux-3.3.5 kernel patch. Since this is totally experimental and
untested, the necessary glue in base-files has not been added, the code is
provided as a starting point in case somebody with that hardware wants to help
getting it supported.
The cAP lite (cAPL 2nD) should also be supported once it is determined whether
or not it uses the same board identifier as the mAP lite.
Code has been successfully built and has no side effect (no impact on already
supported devices).
projects / thirdparty / openwrt.git / log
