Dmitry Torokhov [Fri, 15 Aug 2025 19:43:47 +0000 (12:43 -0700)]
Input: gpio_keys - fall back to platform_get_irq() for interrupt-only keys
To allow transitioning away from gpio-keys platform data attempt to
retrieve IRQ for interrupt-only keys using platform_get_irq_optional()
if interrupt is not specified in platform data.
Gianluca Boiano [Sun, 25 Jan 2026 05:34:30 +0000 (21:34 -0800)]
Input: novatek-nvt-ts - drop wake_type check
The wake_type parameter from touchscreen registers is not used for
anything functional - the driver only validates that it matches a
hard-coded expected value per chip variant. This causes probe to fail
on touchscreens that report a different wake_type despite being
otherwise compatible.
Drop the wake_type check and the associated chip data member to allow
the existing compatibles to work with more touchscreen variants.
The tsc2007 can be used not only as resistive touchscreen controller but
also as a ADC IIO sensor. The second use case requires '#io-channel-cells'
property, hence add it.
Marek Vasut [Wed, 21 Jan 2026 23:06:47 +0000 (00:06 +0100)]
Input: ili210x - add support for polling mode
There are designs incorporating Ilitek ILI2xxx touch controller that
do not connect interrupt pin, for example Waveshare 13.3" DSI display.
To support such systems use polling mode for the input device when I2C
client does not have interrupt assigned to it.
Factor out ili210x_firmware_update_noirq() to allow conditional scoped
guard around this code. The scoped guard has to be applied only in case
the IRQ line is connected, and not applied otherwise.
Marek Vasut [Wed, 21 Jan 2026 23:06:46 +0000 (00:06 +0100)]
dt-bindings: touchscreen: trivial-touch: Drop 'interrupts' requirement for old Ilitek
The old Ilitek touch controllers V3 and V6 can operate without
interrupt line, in polling mode. Drop the 'interrupts' property
requirement for those four controllers. To avoid overloading the
trivial-touch, fork the old Ilitek V3/V6 touch controller binding
into separate document.
Dmitry Torokhov [Tue, 20 Jan 2026 18:14:45 +0000 (10:14 -0800)]
Input: appletouch - fix potential race between resume and open
Take the input device's mutex in atp_resume() and atp_recover() to make
sure they are not racing with open and close methods, and use
input_device_enabled() helper to see if communication with the device
needs to be restarted after resume.
Daniel Peng [Mon, 17 Nov 2025 09:40:41 +0000 (17:40 +0800)]
HID: i2c-hid: Add FocalTech FT8112
Information for touchscreen model HKO/RB116AS01-2 as below:
- HID :FTSC1000
- slave address:0X38
- Interface:HID over I2C
- Touch control lC:FT8112
- I2C ID: PNP0C50
Create new binding file for the FocalTech FT8112 due to
new touchscreen chip. Confirm its compatible, reg for the
device via vendor, and set the interrupt and reset gpio
to map for Skywalker platform.
FocalTech FT8112 also uses vcc33/vccio power supply.
Dmitry Torokhov [Wed, 21 Jan 2026 19:55:51 +0000 (11:55 -0800)]
Input: synaptics_i2c - switch to using managed resources
Switch the driver to use managed resources (devm_*) which simplifier
error handling and allows removing synaptics_i2c_remove() methods form
the driver.
Rename "ret" to "error" where makes sense while at it.
Minseong Kim [Wed, 21 Jan 2026 18:02:02 +0000 (10:02 -0800)]
Input: synaptics_i2c - guard polling restart in resume
synaptics_i2c_resume() restarts delayed work unconditionally, even when
the input device is not opened. Guard the polling restart by taking the
input device mutex and checking input_device_enabled() before re-queuing
the delayed work.
Andy Shevchenko [Thu, 13 Nov 2025 15:44:44 +0000 (16:44 +0100)]
Input: gpio_decoder - replace custom loop by gpiod_get_array_value_cansleep()
There is a custom loop that repeats parts of gpiod_get_array_value_cansleep().
Use that in conjunction with bitmap API to make code shorter and easier to
follow.
With this done, add an upper check for amount of GPIOs given based on
the driver's code.
Complete the sizeof(*pointer) conversion for arc_ps2, altera_ps2, and
olpc_apsp drivers. This follows the cleanup initiated in commit 06b449d7f7c3 ("Input: serio - use sizeof(*pointer) instead of sizeof(type)).
Andy Shevchenko [Tue, 20 Jan 2026 20:33:52 +0000 (12:33 -0800)]
Input: wdt87xx_i2c - switch to use dev_err_probe()
Switch to use dev_err_probe() to simplify the error path and
unify a message template. With that being done, drop the now no-op
message for -ENOMEM as allocator will print a big warning anyway
and remove duplicate message for devm_request_threaded_irq().
Kuan-Wei Chiu [Tue, 13 Jan 2026 09:25:59 +0000 (09:25 +0000)]
dt-bindings: input: google,goldfish-events-keypad: Convert to DT schema
Convert the Android Goldfish Events Keypad binding to DT schema format.
Move the file to the input directory to match the subsystem.
Update the example node name to 'keypad' to comply with generic node
naming standards.
In commit 3bdbd0858df6 ("Input: adp5589: remove the driver") the last user
of include/linux/input/adp5589.h was removed along with the whole driver,
thus the header file can be also removed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Fixes: 3bdbd0858df6 ("Input: adp5589: remove the driver") Link: https://patch.msgid.link/20260113151140.3843753-1-vz@mleia.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry Torokhov [Fri, 19 Dec 2025 05:41:04 +0000 (21:41 -0800)]
Input: ilitek_ts_i2c - switch mdelay() to fsleep()
The mdelay() is called in sleeping context and it should be OK to delay
slightly longer than requested, so switch the code to use fsleep() to
avoid spinning.
Andreas Kemnade [Fri, 19 Dec 2025 05:10:50 +0000 (21:10 -0800)]
Input: twl4030 - add TWL603x power button
Like the TWL4030, these PMICs also have a power button feature, so extend
the TWL4030 power button driver. As the irqchip of the TWL6030 mfd driver
does not provide mask, unmask finctions, do it manually.
Input: psmouse-smbus - add WQ_UNBOUND to alloc_workqueue user
Currently if a user enqueue a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistentcy cannot be addressed without refactoring the API.
alloc_workqueue() treats all queues as per-CPU by default, while unbound
workqueues must opt-in via WQ_UNBOUND.
This default is suboptimal: most workloads benefit from unbound queues,
allowing the scheduler to place worker threads where they’re needed and
reducing noise when CPUs are isolated.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6ccfb ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566af ("workqueue: Add new WQ_PERCPU flag")
This specific workload do not benefit from a per-cpu workqueue, so use
WQ_UNBOUND on the custom workqueue instead.
With the introduction of the WQ_PERCPU flag (equivalent to !WQ_UNBOUND),
any alloc_workqueue() caller that doesn’t explicitly specify WQ_UNBOUND
must now use WQ_PERCPU.
Once migration is complete, WQ_UNBOUND can be removed and unbound will
become the implicit default.
Input: synaptics_i2c - replace use of system_wq with system_dfl_wq
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6ccfb ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566af ("workqueue: Add new WQ_PERCPU flag")
This specific workload do not benefit from a per-cpu workqueue, so use
the default unbound workqueue (system_dfl_wq) instead.
Input: palmas-pwrbutton - replace use of system_wq with system_dfl_wq
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6ccfb ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566af ("workqueue: Add new WQ_PERCPU flag")
This specific workload do not benefit from a per-cpu workqueue, so use
the default unbound workqueue (system_dfl_wq) instead.
Input: gpio_keys - replace use of system_wq with system_dfl_wq
Currently if a user enqueues a work item using schedule_delayed_work() the
used wq is "system_wq" (per-cpu wq) while queue_delayed_work() use
WORK_CPU_UNBOUND (used when a cpu is not specified). The same applies to
schedule_work() that is using system_wq and queue_work(), that makes use
again of WORK_CPU_UNBOUND.
This lack of consistency cannot be addressed without refactoring the API.
This patch continues the effort to refactor worqueue APIs, which has begun
with the change introducing new workqueues and a new alloc_workqueue flag:
commit 128ea9f6ccfb ("workqueue: Add system_percpu_wq and system_dfl_wq")
commit 930c2ea566af ("workqueue: Add new WQ_PERCPU flag")
This specific workload do not benefit from a per-cpu workqueue, so use
the default unbound workqueue (system_dfl_wq) instead.
Petr Hodina [Mon, 15 Dec 2025 14:30:03 +0000 (15:30 +0100)]
Input: stmfts - use sysfs_emit() instead of sprintf()
Follow the advice in Documentation/filesystems/sysfs.rst:
show() should only use sysfs_emit() or sysfs_emit_at() when formatting
the value to be returned to user space.
Petr Hodina [Mon, 15 Dec 2025 14:30:02 +0000 (15:30 +0100)]
Input: stmfts - make comments correct
No functional change.
Fixes: 78bcac7b2ae1 ("Input: add support for the STMicroelectronics FingerTip touchscreen") Signed-off-by: Petr Hodina <petr.hodina@protonmail.com> Signed-off-by: David Heidelberg <david@ixit.cz> Link: https://patch.msgid.link/20251215-fts-fixes-v1-2-8c1e3a63ebf1@ixit.cz Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
David Heidelberg [Mon, 15 Dec 2025 14:30:01 +0000 (15:30 +0100)]
Input: stmfts - correct wording for the warning message
We're trying to enable regulator, not disable it.
Fixes: 78bcac7b2ae1 ("Input: add support for the STMicroelectronics FingerTip touchscreen") Suggested-by: Petr Hodina <petr.hodina@protonmail.com> Signed-off-by: David Heidelberg <david@ixit.cz> Link: https://patch.msgid.link/20251215-fts-fixes-v1-1-8c1e3a63ebf1@ixit.cz Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Lukas Bulwahn [Mon, 10 Nov 2025 05:47:33 +0000 (06:47 +0100)]
MAINTAINERS: adjust file entry in HIMAX HX83112B TOUCHSCREEN SUPPORT
Commit a311c777f298 ("dt-bindings: touchscreen: consolidate simple touch
controller to trivial-touch.yaml") aggregates a few touchscreen yaml files
into a common trivial-touch.yaml, but misses to adjust the reference in
HIMAX HX83112B TOUCHSCREEN SUPPORT, which refers to the removed file
himax,hx83112b.yaml.
Make HIMAX HX83112B TOUCHSCREEN SUPPORT refer to trivial-touch.yaml, in
order to inform the maintainer on changes to the device-tree binding
relevant to that hardware driver.
Reword one of the key event error messages to clarify its meaning: it's
not necessarily an incomplete message, more of a mismatch length.
Clarify that and log the expected and received length too.
Vaibhav Gupta [Wed, 10 Dec 2025 21:11:41 +0000 (21:11 +0000)]
Input: pf1550 - remove "defined but unused" warning
If 'CONFIG_PM_SLEEP' is not set, compiler throws warning for *suspend() and
*resume() function for this driver. Using new 'DEFINE_SIMPLE_DEV_PM_OPS'
fixes it.
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Replace the hand-rolled %02x formatting of the Z packet warning in the
BYD driver with the %*ph format specifier. %*ph is the preferred helper
for printing a buffer in hexadecimal and makes the logging clearer and
more consistent.
MIPS: mm: kmalloc tlb_vpn array to avoid stack overflow
Owing to Config4.MMUSizeExt and VTLB/FTLB MMU features later MIPSr2+
cores can have more than 64 TLB entries. Therefore allocate an array
for uniquification instead of placing too an small array on the stack.
Fixes: 35ad7e181541 ("MIPS: mm: tlb-r4k: Uniquify TLB entries on init") Co-developed-by: Maciej W. Rozycki <macro@orcam.me.uk> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable@vger.kernel.org # v6.17+: 9f048fa48740: MIPS: mm: Prevent a TLB shutdown on initial uniquification Cc: stable@vger.kernel.org # v6.17+ Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> Tested-by: Klara Modin <klarasmodin@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
David Howells [Sat, 29 Nov 2025 00:40:11 +0000 (00:40 +0000)]
afs: Fix uninit var in afs_alloc_anon_key()
Fix an uninitialised variable (key) in afs_alloc_anon_key() by setting it
to cell->anonymous_key. Without this change, the error check may return a
false failure with a bad error number.
Most of the time this is unlikely to happen because the first encounter
with afs_alloc_anon_key() will usually be from (auto)mount, for which all
subsequent operations must wait - apart from other (auto)mounts. Once the
call->anonymous_key is allocated, all further calls to afs_request_key()
will skip the call to afs_alloc_anon_key() for that cell.
Fixes: d27c71257825 ("afs: Fix delayed allocation of a cell's anonymous key") Reported-by: Paulo Alcantra <pc@manguebit.org> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Paulo Alcantara <pc@manguebit.org>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: syzbot+41c68824eefb67cdf00c@syzkaller.appspotmail.com
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 28 Nov 2025 22:08:09 +0000 (14:08 -0800)]
Merge tag 'spi-fix-v6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A disappointingly large set of device specific fixes that have built
up since I've been a bit tardy with sending a pull requests as people
kept sending me new new fixes.
The bcm63xx and lpspi issues could lead to corruption so the fixes are
fairly important for the affected parts, the other issues should all
be relatively minor"
* tag 'spi-fix-v6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: nxp-fspi: Propagate fwnode in ACPI case as well
spi: tegra114: remove Kconfig dependency on TEGRA20_APB_DMA
spi: amlogic-spifc-a1: Handle devm_pm_runtime_enable() errors
spi: spi-fsl-lpspi: fix watermark truncation caused by type cast
spi: cadence-quadspi: Fix cqspi_probe() error handling for runtime pm
spi: bcm63xx: fix premature CS deassertion on RX-only transactions
spi: spi-cadence-quadspi: Remove duplicate pm_runtime_put_autosuspend() call
spi: spi-cadence-quadspi: Enable pm runtime earlier to avoid imbalance
Linus Torvalds [Fri, 28 Nov 2025 18:01:24 +0000 (10:01 -0800)]
Merge tag 'vfs-6.18-rc8.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- afs: Fix delayed allocation of a cell's anonymous key
The allocation of a cell's anonymous key is done in a background
thread along with other cell setup such as doing a DNS upcall. The
normal key lookup tries to use the key description on the anonymous
authentication key as the reference for request_key() - but it may
not yet be set, causing an oops
- ovl: fail ovl_lock_rename_workdir() if either target is unhashed
As well as checking that the parent hasn't changed after getting the
lock, the code needs to check that the dentry hasn't been unhashed.
Otherwise overlayfs might try to rename something that has been
removed
- namespace: fix a reference leak in grab_requested_mnt_ns
lookup_mnt_ns() already takes a reference on mnt_ns, and so
grab_requested_mnt_ns() doesn't need to take an extra reference
* tag 'vfs-6.18-rc8.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
afs: Fix delayed allocation of a cell's anonymous key
ovl: fail ovl_lock_rename_workdir() if either target is unhashed
fs/namespace: fix reference leak in grab_requested_mnt_ns
Linus Torvalds [Fri, 28 Nov 2025 17:16:20 +0000 (09:16 -0800)]
Merge tag 'tty-6.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg KH:
"Here are two serial driver fixes for reported issues for 6.18-rc8.
These are:
- fix for a much reported symbol build loop that broke the build for
some kernel configurations
- amba-pl011 driver bugfix for a reported issue
Both have been in linux next (the last for weeks, the first for a
shorter amount of time), with no reported issues"
* tag 'tty-6.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: Fix 8250_rsa symbol loop
serial: amba-pl011: prefer dma_mapping_error() over explicit address checking
Linus Torvalds [Fri, 28 Nov 2025 17:12:40 +0000 (09:12 -0800)]
Merge tag 'usb-6.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt fixes from Greg KH:
"Here are some last-minutes USB and Thunderbolt driver fixes and new
device ids for 6.18-rc8. Included in here are:
- usb storage quirk fixup
- xhci driver fixes for reported issues
- usb gadget driver fixes
- dwc3 driver fixes
- UAS driver fixup
- thunderbolt new device ids
- usb-serial driver new ids
All of these have been in linux-next with no reported issues, many for
many weeks"
* tag 'usb-6.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (21 commits)
usb: gadget: renesas_usbf: Handle devm_pm_runtime_enable() errors
USB: storage: Remove subclass and protocol overrides from Novatek quirk
usb: uas: fix urb unmapping issue when the uas device is remove during ongoing data transfer
usb: dwc3: Fix race condition between concurrent dwc3_remove_requests() call paths
xhci: dbgtty: fix device unregister
usb: storage: sddr55: Reject out-of-bound new_pba
USB: serial: option: add support for Rolling RW101R-GL
usb: typec: ucsi: psy: Set max current to zero when disconnected
usb: gadget: f_eem: Fix memory leak in eem_unwrap
usb: dwc3: pci: Sort out the Intel device IDs
usb: dwc3: pci: add support for the Intel Nova Lake -S
drivers/usb/dwc3: fix PCI parent check
usb: storage: Fix memory leak in USB bulk transport
xhci: sideband: Fix race condition in sideband unregister
xhci: dbgtty: Fix data corruption when transmitting data form DbC to host
xhci: fix stale flag preventig URBs after link state error is cleared
USB: serial: ftdi_sio: add support for u-blox EVK-M101
usb: cdns3: Fix double resource release in cdns3_pci_probe
usb: gadget: udc: fix use-after-free in usb_gadget_state_work
usb: renesas_usbhs: Fix synchronous external abort on unbind
...
* tag 'mailbox-fixes-v6.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
mailbox: th1520: fix clock imbalance on probe failure
mailbox: pcc: don't zero error register
mailbox: mtk-gpueb: Add missing 'static' to mailbox ops struct
mailbox: mtk-cmdq: Refine DMA address handling for the command buffer
mailbox: mailbox-test: Fix debugfs_create_dir error checking
mailbox: omap-mailbox: Check for pending msgs only when mbox is exclusive
Arnd Bergmann [Fri, 21 Nov 2025 21:14:04 +0000 (22:14 +0100)]
Merge tag 'omap-for-v6.19/maintainers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap into arm/fixes
MAINTAINERS: Add entry for TQ-Systems AM335 device trees
* tag 'omap-for-v6.19/maintainers-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap:
MAINTAINERS: Add entry for TQ-Systems AM335 device trees
Linus Torvalds [Fri, 28 Nov 2025 16:20:14 +0000 (08:20 -0800)]
Merge tag 'mmc-v6.18-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
- sdhci-of-dwcmshc: Fix reset handling for some variants
* tag 'mmc-v6.18-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-of-dwcmshc: Promote the th1520 reset handling to ip level
Linus Torvalds [Fri, 28 Nov 2025 16:08:02 +0000 (08:08 -0800)]
Merge tag 'pmdomain-v6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain fixes from Ulf Hansson:
- mediatek: Fix spinlock recursion in probe
- tegra: Use GENPD_FLAG_NO_STAY_ON to restore old behaviour
* tag 'pmdomain-v6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
pmdomain: tegra: Add GENPD_FLAG_NO_STAY_ON flag
pmdomains: mtk-pm-domains: Fix spinlock recursion in probe
Johan Hovold [Fri, 17 Oct 2025 05:54:14 +0000 (07:54 +0200)]
mailbox: th1520: fix clock imbalance on probe failure
The purpose of the devm_add_action_or_reset() helper is to call the
action function in case adding an action ever fails so drop the clock
disable from the error path to avoid disabling the clocks twice.
Fixes: 5d4d263e1c6b ("mailbox: Introduce support for T-head TH1520 Mailbox driver") Cc: Michal Wilczynski <m.wilczynski@samsung.com> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Michal Wilczynski <m.wilczynski@samsung.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Jamie Iles [Wed, 5 Nov 2025 14:42:29 +0000 (14:42 +0000)]
mailbox: pcc: don't zero error register
The error status mask for a type 3/4 subspace is used for reading the
error status, and the bitwise inverse is used for clearing the error
with the intent being to preserve any of the non-error bits. However,
we were previously applying the mask to extract the status and then
applying the inverse to the result which ended up clearing all bits.
Instead, store the inverse mask in the preserve mask and then use that
on the original value read from the error status so that only the error
is cleared.
mailbox: mtk-gpueb: Add missing 'static' to mailbox ops struct
mtk_gpueb_mbox_ops should be declared static. However, due to its const
nature, this specifier was missed, as it compiled fine without it and
with no warning by the compiler.
arc-linux-gcc (GCC) 12.5.0 doesn't seem to like it however, so add the
static to fix that.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202510100629.3nGvrhEU-lkp@intel.com/ Fixes: dbca0eabb821 ("mailbox: add MediaTek GPUEB IPI mailbox") Signed-off-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Jason-JH Lin [Wed, 22 Oct 2025 17:16:30 +0000 (01:16 +0800)]
mailbox: mtk-cmdq: Refine DMA address handling for the command buffer
GCE can only fetch the command buffer address from a 32-bit register.
Some SoCs support a 35-bit command buffer address for GCE, which
requires a right shift of 3 bits before setting the address into
the 32-bit register. A comment has been added to the header of
cmdq_get_shift_pa() to explain this requirement.
To prevent the GCE command buffer address from being DMA mapped beyond
its supported bit range, the DMA bit mask for the device is set during
initialization.
Additionally, to ensure the correct shift is applied when setting or
reading the register that stores the GCE command buffer address,
new APIs, cmdq_convert_gce_addr() and cmdq_revert_gce_addr(), have
been introduced for consistent operations on this register.
The variable type for the command buffer address has been standardized
to dma_addr_t to prevent handling issues caused by type mismatches.
Fixes: 0858fde496f8 ("mailbox: cmdq: variablize address shift in platform") Signed-off-by: Jason-JH Lin <jason-jh.lin@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
Beleswar Padhi [Mon, 3 Nov 2025 20:11:11 +0000 (01:41 +0530)]
mailbox: omap-mailbox: Check for pending msgs only when mbox is exclusive
On TI K3 devices, the mailbox resides in the Always-On power domain
(LPSC_main_alwayson) and is shared among multiple processors. The
mailbox is not solely exclusive to Linux.
Currently, the suspend path checks all FIFO queues for pending messages
and blocks suspend if any are present. This behavior is unnecessary for
K3 devices, since some of the FIFOs are used for RTOS<->RTOS
communication and are independent of Linux.
For FIFOs used in Linux<->RTOS communication, any pending message would
trigger an interrupt, which naturally prevents suspend from completing.
Hence, there is no need for the mailbox driver to explicitly check for
pending messages on K3 platforms.
Introduce a device match flag to indicate whether the mailbox instance
is exclusive to Linux, and skip the pending message check for
non-exclusive instances (such as in K3).
Fixes: a49f991e740f ("arm64: dts: ti: k3-am62-verdin: Add missing cfg for TI IPC Firmware") Closes: https://lore.kernel.org/all/sid7gtg5vay5qgicsl6smnzwg5mnneoa35cempt5ddwjvedaio@hzsgcx6oo74l/ Signed-off-by: Beleswar Padhi <b-padhi@ti.com> Tested-by: Hiago De Franco <hiago.franco@toradex.com> Reviewed-by: Andrew Davis <afd@ti.com> Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
David Howells [Fri, 28 Nov 2025 10:19:05 +0000 (10:19 +0000)]
afs: Fix delayed allocation of a cell's anonymous key
The allocation of a cell's anonymous key is done in a background thread
along with other cell setup such as doing a DNS upcall. In the reported
bug, this is triggered by afs_parse_source() parsing the device name given
to mount() and calling afs_lookup_cell() with the name of the cell.
The normal key lookup then tries to use the key description on the
anonymous authentication key as the reference for request_key() - but it
may not yet be set and so an oops can happen.
This has been made more likely to happen by the fix for dynamic lookup
failure.
Fix this by firstly allocating a reference name and attaching it to the
afs_cell record when the record is created. It can share the memory
allocation with the cell name (unfortunately it can't just overlap the cell
name by prepending it with "afs@" as the cell name already has a '.'
prepended for other purposes). This reference name is then passed to
request_key().
Secondly, the anon key is now allocated on demand at the point a key is
requested in afs_request_key() if it is not already allocated. A mutex is
used to prevent multiple allocation for a cell.
Thirdly, make afs_request_key_rcu() return NULL if the anonymous key isn't
yet allocated (if we need it) and then the caller can return -ECHILD to
drop out of RCU-mode and afs_request_key() can be called.
Note that the anonymous key is kind of necessary to make the key lookup
cache work as that doesn't currently cache a negative lookup, but it's
probably worth some investigation to see if NULL can be used instead.
Fixes: 330e2c514823 ("afs: Fix dynamic lookup to fail on cell lookup failure") Reported-by: syzbot+41c68824eefb67cdf00c@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com> Link: https://patch.msgid.link/800328.1764325145@warthog.procyon.org.uk
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org Signed-off-by: Christian Brauner <brauner@kernel.org>
NeilBrown [Fri, 28 Nov 2025 01:22:35 +0000 (12:22 +1100)]
ovl: fail ovl_lock_rename_workdir() if either target is unhashed
As well as checking that the parent hasn't changed after getting the
lock we need to check that the dentry hasn't been unhashed.
Otherwise we might try to rename something that has been removed.
Reported-by: syzbot+bfc9a0ccf0de47d04e8c@syzkaller.appspotmail.com Fixes: d2c995581c7c ("ovl: Call ovl_create_temp() without lock held.") Signed-off-by: NeilBrown <neil@brown.name> Link: https://patch.msgid.link/176429295510.634289.1552337113663461690@noble.neil.brown.name Tested-by: syzbot+bfc9a0ccf0de47d04e8c@syzkaller.appspotmail.com Reviewed-by: Amir Goldstein <amir73il@gmail.com> Signed-off-by: Christian Brauner <brauner@kernel.org>
Linus Torvalds [Fri, 28 Nov 2025 05:06:27 +0000 (21:06 -0800)]
Merge tag 'drm-fixes-2025-11-28' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"Last one for this round hopefully, mostly the usual suspects,
xe/amdgpu, with some single fixes otherwise.
There is one amdgpu HDMI blackscreen bug that came in late in the
cycle, but it was bisected and the revert is in here.
i915:
- Reject async flips when PSR's selective fetch is enabled
xe:
- Fix resource leak in xe_guc_ct_init_noalloc()'s error path
- Fix stack_depot usage without STACKDEPOT_ALWAYS_INIT
- Fix overflow in conversion from clock tics to msec
Linus Torvalds [Fri, 28 Nov 2025 01:29:15 +0000 (17:29 -0800)]
Merge tag 'dma-mapping-6.18-2025-11-27' of git://git.kernel.org/pub/scm/linux/kernel/git/mszyprowski/linux
Pull dma-mapping fixes from Marek Szyprowski:
"Two last minute fixes for the recently modified DMA API infrastructure:
- proper handling of DMA_ATTR_MMIO in dma_iova_unlink() function (me)
- regression fix for the code refactoring related to P2PDMA (Pranjal
Shrivastava)"
* tag 'dma-mapping-6.18-2025-11-27' of git://git.kernel.org/pub/scm/linux/kernel/git/mszyprowski/linux:
dma-direct: Fix missing sg_dma_len assignment in P2PDMA bus mappings
iommu/dma: add missing support for DMA_ATTR_MMIO for dma_iova_unlink()
Linus Torvalds [Fri, 28 Nov 2025 01:25:46 +0000 (17:25 -0800)]
Merge tag 'acpi-6.18-rc8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"One more urgent ACPI support fix for 6.18
There is one more commit that needs to be reverted after reverting
problematic commit 7a8c994cbb2d ("ACPI: processor: idle: Optimize ACPI
idle driver registration"), so revert it"
* tag 'acpi-6.18-rc8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI: processor: Update cpuidle driver check in __acpi_processor_start()"
Linus Torvalds [Thu, 27 Nov 2025 19:11:03 +0000 (11:11 -0800)]
Merge tag 'ceph-for-6.18-rc8' of https://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A patch to make sparse read handling work in msgr2 secure mode from
Slava and a couple of fixes from Ziming and myself to avoid operating
on potentially invalid memory, all marked for stable"
* tag 'ceph-for-6.18-rc8' of https://github.com/ceph/ceph-client:
libceph: prevent potential out-of-bounds writes in handle_auth_session_key()
libceph: replace BUG_ON with bounds check for map->max_osd
ceph: fix crash in process_v2_sparse_read() for encrypted directories
libceph: drop started parameter of __ceph_open_session()
libceph: fix potential use-after-free in have_mon_and_osd_map()
- sched: fix TCF_LAYER_TRANSPORT handling in tcf_get_base_ptr()
- bluetooth: mediatek: fix kernel crash when releasing iso interface
- vhost: rewind next_avail_head while discarding descriptors
- eth:
- r8169: fix RTL8127 hang on suspend/shutdown
- aquantia: add missing descriptor cache invalidation on ATL2
- dsa: microchip: fix resource releases in error path"
* tag 'net-6.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
mptcp: Initialise rcv_mss before calling tcp_send_active_reset() in mptcp_do_fastclose().
net: fec: do not register PPS event for PEROUT
net: fec: do not allow enabling PPS and PEROUT simultaneously
net: fec: do not update PEROUT if it is enabled
net: fec: cancel perout_timer when PEROUT is disabled
net: mctp: unconditionally set skb->dev on dst output
net: atlantic: fix fragment overflow handling in RX path
MAINTAINERS: separate VIRTIO NET DRIVER and add netdev
virtio-net: avoid unnecessary checksum calculation on guest RX
eth: fbnic: Fix counter roll-over issue
mptcp: clear scheduled subflows on retransmit
net: dsa: sja1105: fix SGMII linking at 10M or 100M but not passing traffic
s390/net: list Aswin Karuvally as maintainer
net: wwan: mhi: Keep modem name match with Foxconn T99W640
vhost: rewind next_avail_head while discarding descriptors
net/sched: em_canid: fix uninit-value in em_canid_match
can: rcar_canfd: Fix CAN-FD mode as default
xsk: avoid data corruption on cq descriptor number
r8169: fix RTL8127 hang on suspend/shutdown
net: sxgbe: fix potential NULL dereference in sxgbe_rx()
...
Andy Shevchenko [Wed, 26 Nov 2025 20:25:01 +0000 (21:25 +0100)]
spi: nxp-fspi: Propagate fwnode in ACPI case as well
Propagate fwnode of the ACPI device to the SPI controller Linux device.
Currently only OF case propagates fwnode to the controller.
While at it, replace several calls to dev_fwnode() with a single one
cached in a local variable, and unify checks for fwnode type by using
is_*_node() APIs.
====================
net: fec: fix some PTP related issues
There are some issues which were introduced by the commit 350749b909bf
("net: fec: Add support for periodic output signal of PPS"). See each
patch for more details.
====================
Wei Fang [Tue, 25 Nov 2025 08:52:10 +0000 (16:52 +0800)]
net: fec: do not register PPS event for PEROUT
There are currently two situations that can trigger the PTP interrupt,
one is the PPS event, the other is the PEROUT event. However, the irq
handler fec_pps_interrupt() does not check the irq event type and
directly registers a PPS event into the system, but the event may be
a PEROUT event. This is incorrect because PEROUT is an output signal,
while PPS is the input of the kernel PPS system. Therefore, add a check
for the event type, if pps_enable is true, it means that the current
event is a PPS event, and then the PPS event is registered.
Wei Fang [Tue, 25 Nov 2025 08:52:09 +0000 (16:52 +0800)]
net: fec: do not allow enabling PPS and PEROUT simultaneously
In the current driver, PPS and PEROUT use the same channel to generate
the events, so they cannot be enabled at the same time. Otherwise, the
later configuration will overwrite the earlier configuration. Therefore,
when configuring PPS, the driver will check whether PEROUT is enabled.
Similarly, when configuring PEROUT, the driver will check whether PPS
is enabled.
projects / thirdparty / kernel / linux.git / log
