DECnet is an obsolete network protocol that receives more attention
from kernel janitors than users. It belongs in computer protocol
history museum not in Linux kernel.
It has been "Orphaned" in kernel since 2010. The iproute2 support
for DECnet was dropped in 5.0 release. The documentation link on
Sourceforge says it is abandoned there as well.
Leave the UAPI alone to keep userspace programs compiling.
This means that there is still an empty neighbour table
for AF_DECNET.
The table of /proc/sys/net entries was updated to match
current directories and reformatted to be alphabetical.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: David Ahern <dsahern@kernel.org> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reports that in its stress test for resize ioctl, the log writing
function nilfs_segctor_do_construct hits a WARN_ON in
nilfs_segctor_truncate_segments().
It turned out that there is a problem with the current implementation of
the resize ioctl, which changes the writable range on the device (the
range of allocatable segments) at the end of the resize process.
This order is necessary for file system expansion to avoid corrupting the
superblock at trailing edge. However, in the case of a file system
shrink, if log writes occur after truncating out-of-bounds trailing
segments and before the resize is complete, segments may be allocated from
the truncated space.
The userspace resize tool was fine as it limits the range of allocatable
segments before performing the resize, but it can run into this issue if
the resize ioctl is called alone.
Fix this issue by changing nilfs_sufile_resize() to update the range of
allocatable segments immediately after successful truncation of segment
space in case of file system shrink.
A syzbot fault injection test reported that nilfs_btnode_create_block, a
helper function that allocates a new node block for b-trees, causes a
kernel BUG for disk images where the file system block size is smaller
than the page size.
This was due to unexpected flags on the newly allocated buffer head, and
it turned out to be because the buffer flags were not cleared by
nilfs_btnode_abort_change_key() after an error occurred during a b-tree
update operation and the buffer was later reused in that state.
Fix this issue by using nilfs_btnode_delete() to abandon the unused
preallocated buffer in nilfs_btnode_abort_change_key().
The given value of 1518 seems to refer to the layer 2 ethernet frame
size without 802.1Q tag. Actual use of the "max-frame-size" including in
the consumer of the "altr,tse-1.0" compatible is the MTU.
When changing a file size with fallocate() the new size isn't being
checked. In particular, the FSIZE ulimit isn't being checked, which makes
fstest generic/228 fail. Simply adding a call to inode_newsize_ok() fixes
this issue.
Link: https://lkml.kernel.org/r/20230529152645.32680-1-lhenriques@suse.de Signed-off-by: Luís Henriques <lhenriques@suse.de> Reviewed-by: Mark Fasheh <mark@fasheh.com> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's trivial to trigger a use-after-free bug in the ocfs2 quotas code using
fstest generic/452. After a read-only remount, quotas are suspended and
ocfs2_mem_dqinfo is freed through ->ocfs2_local_free_info(). When unmounting
the filesystem, an UAF access to the oinfo will eventually cause a crash.
BUG: KASAN: slab-use-after-free in timer_delete+0x54/0xc0
Read of size 8 at addr ffff8880389a8208 by task umount/669
...
Call Trace:
<TASK>
...
timer_delete+0x54/0xc0
try_to_grab_pending+0x31/0x230
__cancel_work_timer+0x6c/0x270
ocfs2_disable_quotas.isra.0+0x3e/0xf0 [ocfs2]
ocfs2_dismount_volume+0xdd/0x450 [ocfs2]
generic_shutdown_super+0xaa/0x280
kill_block_super+0x46/0x70
deactivate_locked_super+0x4d/0xb0
cleanup_mnt+0x135/0x1f0
...
</TASK>
Link: https://lkml.kernel.org/r/20230522102112.9031-1-lhenriques@suse.de Signed-off-by: Luís Henriques <lhenriques@suse.de> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing code silently converts read operations with the
REQ_FUA bit set into write-barrier operations. This results in data
loss as the backend scribbles zeroes over the data instead of returning
it.
While the REQ_FUA bit doesn't make sense on a read operation, at least
one well-known out-of-tree kernel module does set it and since it
results in data loss, let's be safe here and only look at REQ_FUA for
writes.
PAGE_OFFSET is technically a virtual address so when checking the value of
initrd_start against it we should make sure that it has been sanitised from
the values passed by the bootloader. Without this change, even with a bootloader
that passes correct addresses for an initrd, we are failing to load it on MT7621
boards, for example.
Various fixes for the Au1200/Au1550/Au1300 DBDMA2 code:
- skip cache invalidation if chip has working coherency circuitry.
- invalidate KSEG0-portion of the (physical) data address.
- force the dma channel doorbell write out to bus immediately with
a sync.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The logic used for power_supply_is_system_supplied() counts all power
supplies and assumes that the system is running from AC if there is
either a non-battery power-supply reporting to be online or if no
power-supplies exist at all.
The second rule is for desktop systems, that don't have any
battery/charger devices. These systems will incorrectly report to be
powered from battery once a device scope power-supply is registered
(e.g. a HID device), since these power-supplies increase the counter.
Apart from HID devices, recent dGPUs provide UCSI power supplies on a
desktop systems. The dGPU by default doesn't have anything plugged in so
it's 'offline'. This makes power_supply_is_system_supplied() return 0
with a count of 1 meaning all drivers that use this get a wrong judgement.
To fix this case adjust the logic to also examine the scope of the power
supply. If the power supply is deemed a device power supply, then don't
count it.
Cc: Evan Quan <Evan.Quan@amd.com> Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reduce the amount of output this dev_dbg() statement emits into logs,
otherwise if system software polls the sysfs entry for data and keeps
getting -ENODATA, it could end up filling the logs up.
This does in fact make systemd journald choke, since during boot the
sysfs power supply entries are polled and if journald starts at the
same time, the journal is just being repeatedly filled up, and the
system stops on trying to start journald without booting any further.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use mod_delayed_work() instead of separate cancel_delayed_work_sync() +
schedule_delayed_work() calls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As soon as devm_power_supply_register() has called device_add()
the external_power_changed callback can get called. So there is a window
where ab8500_btemp_external_power_changed() may get called while
di->btemp_psy has not been set yet leading to a NULL pointer dereference.
Fixing this is easy. The external_power_changed callback gets passed
the power_supply which will eventually get stored in di->btemp_psy,
so ab8500_btemp_external_power_changed() can simply directly use
the passed in psy argument which is always valid.
And the same applies to ab8500_fg_external_power_changed().
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ben reports that this should not have been backported to the older
kernels as the rest of the macro is not empty. It was a clean-up patch
in 6.4-rc1 only, it did not add new device ids.
which may fail for example (or other errors could happen). When the
failure occurs, btrfs_relocate_block_group() detects the error and frees
rc and doesn't set fs_info->reloc_ctl to NULL. After that, in
btrfs_init_reloc_root(), rc is retrieved from fs_info->reloc_ctl and
then used, which may cause a use-after-free bug.
This possible bug can be triggered by calling btrfs_ioctl_balance()
before calling btrfs_ioctl_defrag().
To fix this possible bug, in prepare_to_relocate(), check if
btrfs_commit_transaction() fails. If the failure occurs,
unset_reloc_control() is called to set fs_info->reloc_ctl to NULL.
The error log in our fault-injection testing is shown as follows:
There are a few places where we don't check the return value of
btrfs_commit_transaction in relocation.c. Thankfully all these places
have straightforward error handling, so simply change all of the sites
at once.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Stefan Ghinea <stefan.ghinea@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ext4_xattr_block_set() relies on its caller to call dquot_initialize()
on the inode. To assure that this has happened there are WARN_ON
checks. Unfortunately, this is subject to false positives if there is
an antagonist thread which is flipping the file system at high rates
between r/o and rw. So only do the check if EXT4_XATTR_DEBUG is
enabled.
If pm runtime resume fails the .remove callback used to exit early. This
resulted in an error message by the driver core but the device gets
removed anyhow. This lets the registered i2c adapter stay around with an
unbound parent device.
So only skip clk disabling if resume failed, but do delete the adapter.
Similar to commit 0f7d9b31ce7a ("netfilter: nf_tables: fix use-after-free
in nft_set_catchall_destroy()"). We can not access k after kfree_rcu()
call.
Cc: stable@vger.kernel.org Signed-off-by: Min Li <lm0963hack@gmail.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between capsnaps flush and removing the inode from
'mdsc->snap_flush_list' list:
== Thread A == == Thread B ==
ceph_queue_cap_snap()
-> allocate 'capsnapA'
->ihold('&ci->vfs_inode')
->add 'capsnapA' to 'ci->i_cap_snaps'
->add 'ci' to 'mdsc->snap_flush_list'
...
== Thread C ==
ceph_flush_snaps()
->__ceph_flush_snaps()
->__send_flush_snap()
handle_cap_flushsnap_ack()
->iput('&ci->vfs_inode')
this also will release 'ci'
...
== Thread D ==
ceph_handle_snap()
->flush_snaps()
->iterate 'mdsc->snap_flush_list'
->get the stale 'ci'
->remove 'ci' from ->ihold(&ci->vfs_inode) this
'mdsc->snap_flush_list' will WARNING
To fix this we will increase the inode's i_count ref when adding 'ci'
to the 'mdsc->snap_flush_list' list.
According to Alex, most APUs from that time seem to have the same issue
(vbios says 48Mhz, actual is 100Mhz). I only have a CHIP_STONEY so I
limit the fixup to CHIP_STONEY
While doing my research to improve the xpad device names I noticed
that the 1532:0037 VID/PID seems to be used by the DeathAdder 2013,
so that Razer Sabertooth instance looked wrong and very suspect to
me. I didn't see any mention in the official drivers, either.
After doing more research, it turns out that the xpad list
is used by many other projects (like Steam) as-is [1], this
issue was reported [2] and Valve/Sam Lantinga fixed it [3]:
(With multiple Internet users reporting similar issues, not linked here)
After not being able to find the correct VID/PID combination anywhere
on the Internet and not receiving any reply from Razer support I did
some additional detective work, it seems like it presents itself as
"Razer Sabertooth Gaming Controller (XBOX360)", code 1689:FE00.
Leaving us with this:
* Razer Sabertooth (1689:fe00)
* Razer Sabertooth Elite (24c6:5d04)
* Razer DeathAdder 2013 (1532:0037) [note: not a gamepad]
So, to sum things up; remove this conflicting/duplicate entry:
As the real/correct one is already present there, even if
the Internet as a whole insists on presenting it as the
Razer Sabertooth Elite, which (by all accounts) is not:
Syzkaller got a lot of crashes like:
KASAN: use-after-free Write in *_timers*
All of these crashes point to the same memory area:
The buggy address belongs to the object at ffff88801f870000
which belongs to the cache kmalloc-8k of size 8192
The buggy address is located 5320 bytes inside of
8192-byte region [ffff88801f870000, ffff88801f872000)
This area belongs to :
batadv_priv->batadv_priv_dat->delayed_work->timer_list
The reason for these issues is the lack of synchronization. Delayed
work (batadv_dat_purge) schedules new timer/work while the device
is being deleted. As the result new timer/delayed work is set after
cancel_delayed_work_sync() was called. So after the device is freed
the timer list contains pointer to already freed memory.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Cc: stable@kernel.org Fixes: 2f1dfbe18507 ("batman-adv: Distributed ARP Table - implement local storage") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Acked-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF. If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag. If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side. The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.
Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly. For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information. If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.
Fixes: cf6645f8ebc6 ("bnxt_en: Add function for VF driver to query default VLAN.") Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
irq_cpu_rmap_release() calls cpu_rmap_put(), which may free the rmap.
So we need to clear the pointer to our glue structure in rmap before
doing that, not after.
Fixes: 4e0473f1060a ("lib: cpu_rmap: Avoid use after free on rmap->obj array entries") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/ZHo0vwquhOy3FaXc@decadent.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
rtm_tca_policy is used from net/sched/sch_api.c and net/sched/cls_api.c,
thus should be declared in an include file.
This fixes the following sparse warning:
net/sched/sch_api.c:1434:25: warning: symbol 'rtm_tca_policy' was not declared. Should it be static?
Fixes: e331473fee3d ("net/sched: cls_api: add missing validation of netlink attributes") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When receiving a connect response we should make sure that the DCID is
within the valid range and that we don't already have another channel
allocated for the same DCID.
Missing checks may violate the specification (BLUETOOTH CORE SPECIFICATION
Version 5.4 | Vol 3, Part A, Page 1046).
Fixes: 40624183c202 ("Bluetooth: L2CAP: Add missing checks for invalid LE DCID") Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
L2CAP assumes that the locks conn->chan_lock and chan->lock are
acquired in the order conn->chan_lock, chan->lock to avoid
potential deadlock.
For example, l2sock_shutdown acquires these locks in the order:
mutex_lock(&conn->chan_lock)
l2cap_chan_lock(chan)
However, l2cap_disconnect_req acquires chan->lock in
l2cap_get_chan_by_scid first and then acquires conn->chan_lock
before calling l2cap_chan_del. This means that these locks are
acquired in unexpected order, which leads to potential deadlock:
l2cap_chan_lock(c)
mutex_lock(&conn->chan_lock)
This patch releases chan->lock before acquiring the conn_chan_lock
to avoid the potential deadlock.
Fixes: a2a9339e1c9d ("Bluetooth: L2CAP: Fix use-after-free in l2cap_disconnect_{req,rsp}") Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is usually better to request all necessary resources (clocks,
regulators, ...) before starting to make use of them. That way they do
not change state in case one of the resources is not available yet and
probe deferral (-EPROBE_DEFER) is necessary. This is particularly
important for DMA channels and IOMMUs which are not enforced by
fw_devlink yet (unless you use fw_devlink.strict=1).
spi-qup does this in the wrong order, the clocks are enabled and
disabled again when the DMA channels are not available yet.
This causes issues in some cases: On most SoCs one of the SPI QUP
clocks is shared with the UART controller. When using earlycon UART is
actively used during boot but might not have probed yet, usually for
the same reason (waiting for the DMA controller). In this case, the
brief enable/disable cycle ends up gating the clock and further UART
console output will halt the system completely.
Avoid this by requesting the DMA channels before changing the clock
state.
Not upstream as it was fixed in a much larger api change in newer
kernels.
gcc-13 rightfully complains that enum is not the same as an int, so fix
up the function prototypes in i40e_alloc.h to be correct, solving a
bunch of build warnings.
Not upstream as this function is no longer around anymore.
The function i40iw_manage_apbvt() has the wrong prototype match from the
.h file to the .c declaration, so fix it up, otherwise gcc-13 complains
(rightfully) that the type is incorrect.
Since IQK could spend time, we make a cache of IQK result matrix that looks
like iqk_matrix[channel_idx].val[x][y], and we can reload the matrix if we
have made a cache. To determine a cache is made, we check
iqk_matrix[channel_idx].val[0][0].
The initial commit 7274a8c22980 ("rtlwifi: rtl8192de: Merge phy routines")
make a mistake that checks incorrect iqk_matrix[channel_idx].val[0] that
is always true, and this mistake is found by commit ee3db469dd31
("wifi: rtlwifi: remove always-true condition pointed out by GCC 12"), so
I recall the vendor driver to find fix and apply the correctness.
Descriptor table is a shared resource; two fget() on the same descriptor
may return different struct file references. get_tap_ptr_ring() is
called after we'd found (and pinned) the socket we'll be using and it
tries to find the private tun/tap data structures associated with it.
Redoing the lookup by the same file descriptor we'd used to get the
socket is racy - we need to same struct file.
Thanks to Jason for spotting a braino in the original variant of patch -
I'd missed the use of fd == -1 for disabling backend, and in that case
we can end up with sock == NULL and sock != oldsock.
Cc: stable@kernel.org Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[4.14: Account for get_tap_skb_array() instead of get_tap_ptr_ring()] Signed-off-by: Samuel Mendoza-Jonas <samjonas@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16.
Fixes: 0fa81b304a79 ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block") Signed-off-by: Alexander Bersenev <bay@hackerdom.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NCM specification defines two formats of transfer blocks: with 16-bit
fields (NTB-16) and with 32-bit fields (NTB-32). Currently only NTB-16 is
implemented.
This patch adds the support of NTB-32. The motivation behind this is that
some devices such as E5785 or E5885 from the current generation of Huawei
LTE routers do not support NTB-16. The previous generations of Huawei
devices are also use NTB-32 by default.
Also this patch enables NTB-32 by default for Huawei devices.
During the 2019 ValdikSS made five attempts to contact Huawei to add the
NTB-16 support to their router firmware, but they were unsuccessful.
Signed-off-by: Alexander Bersenev <bay@hackerdom.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7e01c7f7046e ("net: cdc_ncm: Deal with too low values of dwNtbOutMaxSize") Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Sat, 27 May 2023 13:52:48 +0000 (15:52 +0200)]
scsi: dpt_i2o: Do not process completions with invalid addresses
adpt_isr() reads reply addresses from a hardware register, which
should always be within the DMA address range of the device's pool of
reply address buffers. In case the address is out of range, it tries
to muddle on, converting to a virtual address using bus_to_virt().
bus_to_virt() does not take DMA addresses, and it doesn't make sense
to try to handle the completion in this case. Ignore it and continue
looping to service the interrupt. If a completion has been lost then
the SCSI core should eventually time-out and trigger a reset.
There is no corresponding upstream commit, because this driver was
removed upstream.
Fixes: 67af2b060e02 ("[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt ...") Signed-off-by: Ben Hutchings <benh@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adpt_i2o_passthru() takes a user-provided message and passes it
through to the hardware with appropriate translation of addresses
and message IDs. It has a number of bugs:
- When a message requires scatter/gather, it doesn't verify that the
offset to the scatter/gather list is less than the message size.
- When a message requires scatter/gather, it overwrites the DMA
addresses with the user-space virtual addresses before unmapping the
DMA buffers.
- It reads the message from user memory multiple times. This allows
user-space to change the message and bypass validation.
- It assumes that the message is at least 4 words long, but doesn't
check that.
I tried fixing these, but even the maintainer of the corresponding
user-space in Debian doesn't have the hardware any more.
Instead, remove the pass-through ioctl (I2OUSRCMD) and supporting
code.
There is no corresponding upstream commit, because this driver was
removed upstream.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: 67af2b060e02 ("[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt ...") Signed-off-by: Ben Hutchings <benh@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: null-ptr-deref in soft_cursor+0x384/0x6b4 drivers/video/fbdev/core/softcursor.c:70
Read of size 16 at addr 0000000000000200 by task kworker/u4:1/12
Treat i_data_sem for ea_inodes as being in their own lockdep class to
avoid lockdep complaints about ext4_setattr's use of inode_lock() on
normal inodes potentially causing lock ordering with i_data_sem on
ea_inodes in ext4_xattr_inode_write(). However, ea_inodes will be
operated on by ext4_setattr(), so this isn't a problem.
The Linux Kernel currently only requires make v3.82 while the grouped
target functionality requires make v4.3. Removed the grouped target
introduced in 4ce1f694eb5d ("selinux: ensure av_permissions.h is
built when needed") as well as the multiple header file targets in
the make rule. This effectively reverts the problem commit.
We will revisit this change when make >= 4.3 is required by the rest
of the kernel.
Cc: stable@vger.kernel.org Fixes: 4ce1f694eb5d ("selinux: ensure av_permissions.h is built when needed") Reported-by: Erwan Velu <e.velu@criteo.com> Reported-by: Luiz Capitulino <luizcap@amazon.com> Tested-by: Luiz Capitulino <luizcap@amazon.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART IP now has two known bugs, one is that CTS has higher priority
than the break signal, which causes the break signal sending through
UARTCTRL_SBK may impacted by the CTS input if the HW flow control is
enabled. It exists on all platforms we support in this driver.
So we add a workaround patch for this issue: commit c4c81db5cf8b
("tty: serial: fsl_lpuart: disable the CTS when send break signal").
Another IP bug is i.MX8QM LPUART may have an additional break character
being sent after SBK was cleared. It may need to add some delay between
clearing SBK and re-enabling CTS to ensure that the SBK latch are
completely cleared.
But we found that during the delay period before CTS is enabled, there
is still a risk that Bluetooth data in TX FIFO may be sent out during
this period because of break off and CTS disabled(even if BT sets CTS
line deasserted, data is still sent to BT).
Due to this risk, we have to drop the CTS-disabling workaround for SBK
bugs, use TXINV seems to be a better way to replace SBK feature and
avoid above risk. Also need to disable the transmitter to prevent any
data from being sent out during break, then invert the TX line to send
break. Then disable the TXINV when turn off break and re-enable
transmitter.
Fixes: c4c81db5cf8b ("tty: serial: fsl_lpuart: disable the CTS when send break signal") Cc: stable <stable@kernel.org> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230519094751.28948-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may get an empty response with zero length at the beginning of
the driver start and get following UBSAN error. Since there is no
content(SDRT_NONE) for the response, just return and skip the response
handling to avoid this problem.
Test pass : SDIO wifi throughput test with this patch
Clang warns that the address of a pointer will always evaluated as true
in a boolean context:
drivers/regulator/da9052-regulator.c:423:22: warning: address of array
'pdata->regulators' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (pdata && pdata->regulators) {
~~ ~~~~~~~^~~~~~~~~~
drivers/regulator/da9055-regulator.c:615:22: warning: address of array
'pdata->regulators' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (pdata && pdata->regulators) {
~~ ~~~~~~~^~~~~~~~~~
Link: https://github.com/ClangBuiltLinux/linux/issues/142 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
../lib/dynamic_debug.c:1034:24: warning: array comparison always
evaluates to false [-Wtautological-compare]
if (__start___verbose == __stop___verbose) {
^
1 warning generated.
These are not true arrays, they are linker defined symbols, which are just
addresses. Using the address of operator silences the warning and does
not change the resulting assembly with either clang/ld.lld or gcc/ld
(tested with diff + objdump -Dr).
../kernel/extable.c:37:52: warning: array comparison always evaluates to
a constant [-Wtautological-compare]
if (main_extable_sort_needed && __stop___ex_table > __start___ex_table) {
^
1 warning generated.
These are not true arrays, they are linker defined symbols, which are just
addresses. Using the address of operator silences the warning and does
not change the resulting assembly with either clang/ld.lld or gcc/ld
(tested with diff + objdump -Dr).
drivers/net/ethernet/sun/cassini.c:1316:29: error: comparison between two arrays [-Werror=array-compare]
drivers/net/ethernet/sun/cassini.c:3783:34: error: comparison between two arrays [-Werror=array-compare]
Note that 2 arrays should be compared by comparing of their addresses:
note: use ‘&cas_prog_workaroundtab[0] == &cas_prog_null[0]’ to compare the addresses
Signed-off-by: Martin Liska <mliska@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the concept of checking for dangling pointers to local variables
at function exit is really interesting, the gcc-12 implementation is not
compatible with reality, and results in false positives.
For example, gcc sees us putting things on a local list head allocated
on the stack, which involves exactly those kinds of pointers to the
local stack entry:
In function ‘__list_add’,
inlined from ‘list_add_tail’ at include/linux/list.h:102:2,
inlined from ‘rebuild_snap_realms’ at fs/ceph/snap.c:434:2:
include/linux/list.h:74:19: warning: storing the address of local variable ‘realm_queue’ in ‘*&realm_27(D)->rebuild_item.prev’ [-Wdangling-pointer=]
74 | new->prev = prev;
| ~~~~~~~~~~^~~~~~
But then gcc - understandably - doesn't really understand the big
picture how the doubly linked list works, so doesn't see how we then end
up emptying said list head in a loop and the pointer we added has been
removed.
Gcc also complains about us (intentionally) using this as a way to store
a kind of fake stack trace, eg
drivers/acpi/acpica/utdebug.c:40:38: warning: storing the address of local variable ‘current_sp’ in ‘acpi_gbl_entry_stack_pointer’ [-Wdangling-pointer=]
40 | acpi_gbl_entry_stack_pointer = ¤t_sp;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
which is entirely reasonable from a compiler standpoint, and we may want
to change those kinds of patterns, but not not.
So this is one of those "it would be lovely if the compiler were to
complain about us leaving dangling pointers to the stack", but not this
way.
Address of a field inside a struct can't possibly be null; gcc-12 warns
about this.
Signed-off-by: Adam Borowski <kilobyte@angband.pl> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC 11 (incorrectly[1]) assumes that literal values cast to (void *)
should be treated like a NULL pointer with an offset, and raises
diagnostics when doing bounds checking under -Warray-bounds. GCC 12
got "smarter" about finding these:
In function 'rdfs8',
inlined from 'vga_recalc_vertical' at /srv/code/arch/x86/boot/video-mode.c:124:29,
inlined from 'set_mode' at /srv/code/arch/x86/boot/video-mode.c:163:3:
/srv/code/arch/x86/boot/boot.h:114:9: warning: array subscript 0 is outside array bounds of 'u8[0]' {aka 'unsigned char[]'} [-Warray-bounds]
114 | asm volatile("movb %%fs:%1,%0" : "=q" (v) : "m" (*(u8 *)addr));
| ^~~
This has been solved in other places[2] already by using the recently
added absolute_pointer() macro. Do the same here.
For devices not attached to a port multiplier and managed directly by
libata, the device number passed to ata_find_dev() must always be lower
than the maximum number of devices returned by ata_link_max_devices().
That is 1 for SATA devices or 2 for an IDE link with master+slave
devices. This device number is the SCSI device ID which matches these
constraints as the IDs are generated per port and so never exceed the
maximum number of devices for the link being used.
However, for libsas managed devices, SCSI device IDs are assigned per
struct scsi_host, leading to device IDs for SATA devices that can be
well in excess of libata per-link maximum number of devices. This
results in ata_find_dev() to always return NULL for libsas managed
devices except for the first device of the target scsi_host with ID
(device number) equal to 0. This issue is visible by executing the
hdparm utility, which fails. E.g.:
hdparm -i /dev/sdX
/dev/sdX:
HDIO_GET_IDENTITY failed: No message of desired type
Fix this by rewriting ata_find_dev() to ignore the device number for
non-PMP attached devices with a link with at most 1 device, that is SATA
devices. For these, the device number 0 is always used to
return the correct pointer to the struct ata_device of the port link.
This change excludes IDE master/slave setups (maximum number of devices
per link is 2) and port-multiplier attached devices. Also, to be
consistant with the fact that SCSI device IDs and channel numbers used
as device numbers are both unsigned int, change the devno argument of
ata_find_dev() to unsigned int.
Reported-by: Xingui Yang <yangxingui@huawei.com> Fixes: 41bda9c98035 ("libata-link: update hotplug to handle PMP links") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:
In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~
See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.
Cc: stable@vger.kernel.org Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f85e ("iio: adc: mxs-lradc: Add support for ADC driver") Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PROC_FS is disabled, the function declarations for some
procfs functions are hidden, but the definitions are still build,
as shown by this compiler warning:
net/atm/resources.c:403:7: error: no previous prototype for 'atm_dev_seq_start' [-Werror=missing-prototypes]
net/atm/resources.c:409:6: error: no previous prototype for 'atm_dev_seq_stop' [-Werror=missing-prototypes]
net/atm/resources.c:414:7: error: no previous prototype for 'atm_dev_seq_next' [-Werror=missing-prototypes]
Add another #ifdef to leave these out of the build.
Two functions are defined and used in pcm_oss.c but also optionally
used from io.c, with an optional prototype. If CONFIG_SND_PCM_OSS_PLUGINS
is disabled, this causes a warning as the functions are not static
and have no prototype:
sound/core/oss/pcm_oss.c:1235:19: error: no previous prototype for 'snd_pcm_oss_write3' [-Werror=missing-prototypes]
sound/core/oss/pcm_oss.c:1266:19: error: no previous prototype for 'snd_pcm_oss_read3' [-Werror=missing-prototypes]
Avoid this by making the prototypes unconditional.
gcc with W=1 and ! CONFIG_NF_NAT
net/netfilter/nf_conntrack_netlink.c:3463:32: error:
‘exp_nat_nla_policy’ defined but not used [-Werror=unused-const-variable=]
3463 | static const struct nla_policy exp_nat_nla_policy[CTA_EXPECT_NAT_MAX+1] = {
| ^~~~~~~~~~~~~~~~~~
net/netfilter/nf_conntrack_netlink.c:2979:33: error:
‘any_addr’ defined but not used [-Werror=unused-const-variable=]
2979 | static const union nf_inet_addr any_addr;
| ^~~~~~~~
These variables use is controlled by CONFIG_NF_NAT, so should their definitions.
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
If scsi_dispatch_cmd() failed, the SCSI command was not sent to the target,
scsi_queue_rq() would return BLK_STS_RESOURCE and the related request would
be requeued. The timeout of this request would not fire, no one would
increase iodone_cnt.
The above flow would result the iodone_cnt smaller than iorequest_cnt. So
decrease the iorequest_cnt if dispatch failed to workaround the issue.
Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Reported-by: Ming Lei <ming.lei@redhat.com> Closes: https://lore.kernel.org/r/ZF+zB+bB7iqe0wGd@ovpn-8-17.pek2.redhat.com Link: https://lore.kernel.org/r/20230515070156.1790181-3-haowenchao2@huawei.com Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Using a semaphore in the wait_event*() condition is no good idea.
It hits a kernel WARN_ON() at prepare_to_wait_event() like:
do not call blocking ops when !TASK_RUNNING; state=1 set at
prepare_to_wait_event+0x6d/0x690
For avoiding the potential deadlock, rewrite to an open-coded loop
instead. Unlike the loop in wait_event*(), this uses wait_woken()
after the condition check, hence the task state stays consistent.
Since dvb_frontend_detach() is not called in ttusb_dec_exit_dvb(),
which is called when the device is disconnected, dvb_frontend_free()
is not finally called.
This causes a memory leak just by repeatedly plugging and
unplugging the device.
Fix this issue by adding dvb_frontend_detach() to ttusb_dec_exit_dvb().
IRQ handler netup_spi_interrupt() takes spinlock spi->lock. The lock
is initialized in netup_spi_init(). However, irq handler is registered
before initializing the lock.
Spinlock dma->lock and i2c->lock suffer from the same problem.
Fix this by registering the irq at the end of probe.
In su3000_read_mac_address, if i2c_transfer fails to execute two
messages, array mac address will not be initialized. Without handling
such error, later in function dvb_usb_adapter_dvb_init, proposed_mac
is accessed before initialization.
Fix this error by returning a negative value if message execution fails.
In digitv_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach digitv_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In rtl28xxu_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach rtl28xxu_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In ce6230_i2c_master_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach ce6230_i2c_master_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In ec168_i2c_xfer, msg is controlled by user. When msg[i].buf is null
and msg[i].len is zero, former checks on msg[i].buf would be passed.
If accessing msg[i].buf[0] without sanity check, null pointer deref
would happen. We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In az6027_i2c_xfer, msg is controlled by user. When msg[i].buf is null,
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in
az6027_i2c_xfer()") fix the null-ptr-deref bug when msg[i].addr is 0x99.
However, null-ptr-deref also happens when msg[i].addr is 0xd0 and 0xc0.
We add check on msg[i].len to prevent null-ptr-deref.
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.
The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
When unwind instruction is 0xb2,the subsequent instructions
are uleb128 bytes.
For now,it uses only the first uleb128 byte in code.
For vsp increments of 0x204~0x400,use one uleb128 byte like below:
0xc06a00e4 <unwind_test_work>: 0x80b27fac
Compact model index: 0
0xb2 0x7f vsp = vsp + 1024
0xac pop {r4, r5, r6, r7, r8, r14}
For vsp increments larger than 0x400,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x01 vsp = vsp + 1032
0xac pop {r4, r5, r6, r7, r8, r14}
The unwind works well since the decoded uleb128 byte is also 0x81.
For vsp increments larger than 0x600,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x02 vsp = vsp + 1544
0xac pop {r4, r5, r6, r7, r8, r14}
In this case,the decoded uleb128 result is 0x101(vsp=0x204+(0x101<<2)).
While the uleb128 used in code is 0x81(vsp=0x204+(0x81<<2)).
The unwind aborts at this frame since it gets incorrect vsp.
To fix this,add uleb128 decode to cover all the above case.
Signed-off-by: Haibo Li <haibo.li@mediatek.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a user can make copy_from_user() fail, there is a potential for
UAF/DF due to a lack of locking around the allocation, use and freeing
of the data buffers.
This issue is not theoretical. I managed to author a POC for it:
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation") Signed-off-by: Andreas Svensson <andreas.svensson@axis.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Syzkaller got the following report:
BUG: KASAN: use-after-free in sk_setup_caps+0x621/0x690 net/core/sock.c:2018
Read of size 8 at addr ffff888027f82780 by task syz-executor276/3255
The function sk_setup_caps (called by ip6_sk_dst_store_flow->
ip6_dst_store) referenced already freed memory as this memory was
freed by parallel task in udpv6_sendmsg->ip6_sk_dst_lookup_flow->
sk_dst_check.
The reason for this race condition is: sk_setup_caps() keeps using
the dst after transferring the ownership to the dst cache.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch replaces the tp->mss_cache check in getting TCP_MAXSEG
with tp->rx_opt.user_mss check for CLOSE/LISTEN sock. Since
tp->mss_cache is initialized with TCP_MSS_DEFAULT, checking if
it's zero is probably a bug.
With this change, getting TCP_MAXSEG before connecting will return
default MSS normally, and return user_mss if user_mss is set.
The value is changed under lock_sock() and po->bind_lock, so we
need READ_ONCE() to access pkt_sk(sk)->num without these locks in
packet_bind_spkt(), packet_bind(), and sk_diag_fill().
Note that WRITE_ONCE() is already added by commit c7d2ef5dd4b0
("net/packet: annotate accesses to po->bind").
BUG: KCSAN: data-race in packet_bind / packet_do_bind
write (marked) to 0xffff88802ffd1cee of 2 bytes by task 7322 on cpu 0:
packet_do_bind+0x446/0x640 net/packet/af_packet.c:3236
packet_bind+0x99/0xe0 net/packet/af_packet.c:3321
__sys_bind+0x19b/0x1e0 net/socket.c:1803
__do_sys_bind net/socket.c:1814 [inline]
__se_sys_bind net/socket.c:1812 [inline]
__x64_sys_bind+0x40/0x50 net/socket.c:1812
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
read to 0xffff88802ffd1cee of 2 bytes by task 7318 on cpu 1:
packet_bind+0xbf/0xe0 net/packet/af_packet.c:3322
__sys_bind+0x19b/0x1e0 net/socket.c:1803
__do_sys_bind net/socket.c:1814 [inline]
__se_sys_bind net/socket.c:1812 [inline]
__x64_sys_bind+0x40/0x50 net/socket.c:1812
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3b/0x90 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x72/0xdc
value changed: 0x0300 -> 0x0000
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7318 Comm: syz-executor.4 Not tainted 6.3.0-13380-g7fddb5b5300c #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Fixes: 96ec6327144e ("packet: Diag core and basic socket info dumping") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230524232934.50950-1-kuniyu@amazon.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Online Amateur Radio Community (OARC) has recently been experimenting
with building a nationwide packet network in the UK.
As part of our experimentation, we have been testing out packet on 300bps HF,
and playing with net/rom. For HF packet at this baud rate you really need
to make sure that your MTU is relatively low; AX.25 suggests a PACLEN of 60,
and a net/rom PACLEN of 40 to go with that.
However the Linux net/rom support didn't work with a low PACLEN;
the mkiss module would truncate packets if you set the PACLEN below about 200 or so, e.g.:
This didn't make any sense to me (if the packets are smaller why would they
be truncated?) so I started investigating.
I looked at the packets using ethereal, and found that many were just huge
compared to what I would expect.
A simple net/rom connection request packet had the request and then a bunch
of what appeared to be random data following it:
</quote>
Simon provided a patch that I slightly revised:
Not only we must not use skb_tailroom(), we also do
not want to count NR_NETWORK_LEN twice.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Co-Developed-by: Simon Kapadia <szymon@kapadia.pl> Signed-off-by: Simon Kapadia <szymon@kapadia.pl> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Simon Kapadia <szymon@kapadia.pl> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230524141456.1045467-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"_start" is used in several arches and proably should be reserved
for ARCH usage. Using it in a driver for a private symbol can cause
a build error when it conflicts with ARCH usage of the same symbol.
Therefore rename pl330's "_start" to "pl330_start_thread" so that there
is no conflict and no build error.
drivers/dma/pl330.c:1053:13: error: '_start' redeclared as different kind of symbol
1053 | static bool _start(struct pl330_thread *thrd)
| ^~~~~~
In file included from ../include/linux/interrupt.h:21,
from ../drivers/dma/pl330.c:18:
arch/riscv/include/asm/sections.h:11:13: note: previous declaration of '_start' with type 'char[]'
11 | extern char _start[];
| ^~~~~~
Fixes: b7d861d93945 ("DMA: PL330: Merge PL330 driver into drivers/dma/") Fixes: ae43b3289186 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Jaswinder Singh <jassisinghbrar@gmail.com> Cc: Boojin Kim <boojin.kim@samsung.com> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Vinod Koul <vkoul@kernel.org> Cc: dmaengine@vger.kernel.org Cc: linux-riscv@lists.infradead.org Link: https://lore.kernel.org/r/20230524045310.27923-1-rdunlap@infradead.org Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously, channel open messages were always sent to monitors on the first
ioctl() call for unbound HCI sockets, even if the command and arguments
were completely invalid. This can leave an exploitable hole with the abuse
of invalid ioctl calls.
This commit hardens the ioctl processing logic by first checking if the
command is valid, and immediately returning with an ENOIOCTLCMD error code
if it is not. This ensures that ioctl calls with invalid commands are free
of side effects, and increases the difficulty of further exploitation by
forcing exploitation to find a way to pass a valid command first.
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn> Co-developed-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Dragos-Marian Panait <dragos.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
