There is little harm in ignoring fractional coordinates
(they just get truncated).
Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24
is rejected. We have the same issue in Kodi when trying to
use zoom options on video.
Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]
it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords
Fixes: 21af94cf1a4c ("drm/vc4: Add support for scaling of display planes.") Signed-off-by: Dom Cobley <popcornmix@gmail.com> Link: https://lore.kernel.org/r/20220613144800.326124-5-maxime@cerno.tech Signed-off-by: Maxime Ripard <maxime@cerno.tech> Signed-off-by: Sasha Levin <sashal@kernel.org>
The core clock computation takes into account both the load due to the
input (ie, planes) and its output (ie, encoders).
However, while the input load needs to consider all the planes, and thus
sum all of their associated loads, the output happens mostly in
parallel.
Therefore, we need to consider only the maximum of all the output loads,
and not the sum like we were doing. This resulted in a clock rate way
too high which could be discarded for being too high by the clock
framework.
Since recent changes, the clock framework will even downright reject it,
leading to a core clock being too low for its current needs.
Fixes: 16e101051f32 ("drm/vc4: Increase the core clock based on HVS load") Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Link: https://lore.kernel.org/r/20220613144800.326124-4-maxime@cerno.tech Signed-off-by: Sasha Levin <sashal@kernel.org>
video_device_alloc() allocates memory for vdev,
when video_register_device() fails, it doesn't release the memory and
leads to memory leak, call video_device_release() to fix this.
Fixes: 704a84ccdbf1 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The stateless decoder API does not specify the usage of SOURCE_CHANGE
and EOF events. These events are used by stateful decoders to signal
changes in the bitstream. They do not make sense for stateless decoders.
Do not handle subscription for these two types of events for stateless
decoder instances. This fixes the last v4l2-compliance error:
Control ioctls:
fail: v4l2-test-controls.cpp(946): have_source_change || have_eos
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: FAIL
Fixes: 8cdc3794b2e3 ("media: mtk-vcodec: vdec: support stateless API") Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver does not use the virt_to_bus() function, though it
depends on x86 specific fixups in the swiotlb code, which was
last rewritten in commit e380a0394c36 ("x86/PCI: sta2x11: use
default DMA address translation").
It is possible that the driver still fails to build on some
architectures that are missing CONFIG_VIRT_TO_BUS, but it is
always set on x86 machines with the STA2X11 platform enabled.
More likely though is that it was never meant to depend on
CONFIG_VIRT_TO_BUS, and the Kconfig dependency was kept from
an out-of-tree version when the driver was originally merged.
Error return values are supposed to be negative in hdpvr_read. Most
error returns are currently handled via an unsigned integer "ret". When
setting a negative error value to "ret", the value actually becomes a
large positive value, because "ret" is unsigned. Later on, the "ret"
value is returned. But as ssize_t is a 64-bit signed number, the error
return value stays a large positive integer instead of a negative
integer. This can cause an error value to be interpreted as the read
size, which can cause a buffer overread for applications relying on the
returned size.
Fixes: 9aba42efe85b ("V4L/DVB (11096): V4L2 Driver for the Hauppauge HD PVR usb capture device") Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Every iteration of for_each_available_child_of_node() decrements
the reference counter of the previous node. There is no decrement
when break out from the loop and results in refcount leak.
Add missing of_node_put() to fix this.
As mipi_dsi_driver_register could return error if fails,
it should be better to check the return value and return error
if fails.
Moreover, if i2c_add_driver fails, mipi_dsi_driver_register
should be reverted.
On shutdown, each CCP device instance performs shutdown processing.
However, __sev_platform_shutdown_locked() uses the controlling psp
structure to obtain the pointer to the sev_device structure. However,
during driver initialization, it is possible that an error can be received
from the firmware that results in the sev_data pointer being cleared from
the controlling psp structure. The __sev_platform_shutdown_locked()
function does not check for this situation and will segfault.
While not common, this scenario should be accounted for. Add a check for a
NULL sev_device structure before attempting to use it.
Fixes: 5441a07a127f ("crypto: ccp - shutdown SEV firmware on kexec") Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
test_sock_fields__detach() got called with a null pointer here when one
of the CHECKs or ASSERTs up to the test_sock_fields__open_and_load()
call resulted in a jump to the "done" label.
A skeletons *__detach() is not safe to call with a null pointer, though.
This led to a segfault.
Go the easy route and only call test_sock_fields__destroy() which is
null-pointer safe and includes detaching.
Came across this while looking[1] to introduce the usage of
bpf_tcp_helpers.h (included in progs/test_sock_fields.c) together with
vmlinux.h.
The prototype of .features is netdev_features_t, it should use
NETIF_F_LLTX and NETIF_F_HW_VLAN_STAG_TX, not NETIF_F_LLTX_BIT
and NETIF_F_HW_VLAN_STAG_TX_BIT.
The RCU priority boosting can fail in two situations:
1) If (nr_cpus= > maxcpus=), which means if the total number of CPUs
is higher than those brought online at boot, then torture_onoff() may
later bring up CPUs that weren't online on boot. Now since rcutorture
initialization only boosts the ksoftirqds of the CPUs that have been
set online on boot, the CPUs later set online by torture_onoff won't
benefit from the boost, making RCU priority boosting fail.
2) The ksoftirqd kthreads are boosted after the creation of
rcu_torture_boost() kthreads, which opens a window large enough for these
rcu_torture_boost() kthreads to wait (despite running at FIFO priority)
for ksoftirqds that are still running at SCHED_NORMAL priority.
A recent change to the DEBUG_INFO Kconfig option means that simply adding
CONFIG_DEBUG_INFO=y to the .config file and running "make oldconfig" no
longer works. It is instead necessary to add CONFIG_DEBUG_INFO_NONE=n
and (for example) CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y.
This combination will then result in CONFIG_DEBUG_INFO being selected.
This commit therefore updates the Kconfig options produced in response
to the kvm.sh --gdb, --kasan, and --kcsan Kconfig options.
Fixes: f9b3cd245784 ("Kconfig.debug: make DEBUG_INFO selectable from a choice") Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
KASAN allots significant memory to track allocation state, and the amount
of memory has increased recently, which results in frequent OOMs on a
few of the rcutorture scenarios. This commit therefore provides 2G of
memory for --kasan runs, up from the 512M default.
Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
radeon is MIT. This were incorrectly changed in
commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
and
commit d198b34f3855 (".gitignore: add SPDX License Identifier")
and:
commit ec8f24b7faaf ("treewide: Add SPDX license identifier - Makefile/Kconfig")
Fixes: d198b34f3855 (".gitignore: add SPDX License Identifier") Fixes: ec8f24b7faaf ("treewide: Add SPDX license identifier - Makefile/Kconfig") Fixes: b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2053 Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The DPK is a kind of RF calibration whose algorithm is to fine tune
parameters and calibrate, and check the result. If the result isn't good
enough, it could adjust parameters and try again.
This issue is to read and show the result, but it could be a negative
calibration result that causes divisor 0 and core dump. So, fix it by
phy_div() that does division only if divisor isn't zero; otherwise,
zero is adopted.
As a result of the execution of the inner while loop, the value
of 'idx' can be equal to LINK_QUAL_MAX_RETRY_NUM. However, this
is not checked after the loop and 'idx' is used to write the
LINK_QUAL_MAX_RETRY_NUM size array 'lq_cmd->rs_table[idx]' below
in the outer loop.
The fix is to check the new value of 'idx' inside the nested loop,
and break both loops if index equals the size. Checking it at the
start is now pointless, so let's remove it.
Detected using the static analysis tool - Svace.
Fixes: be663ab67077 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220608171614.28891-1-aleksei.kodanev@bell-sw.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to not add fancy protection for drv_priv we can move
htc_handle->drv_priv initialization at the end of the
ath9k_htc_probe_device() and add helper macro to make
all *_STAT_* macros NULL safe, since syzbot has reported related NULL
deref in that macros [1]
When converting to full Virtual Channel routing an error crept into the
routing table for Ebisu (r8a77990). The routing information is used at
probe time preventing rcar-vin from probing correctly on this SoC, solve
by correcting the routing table.
Fixes: 3e52419ec04f9769 ("media: rcar-{csi2,vin}: Move to full Virtual Channel routing per CSI-2 IP") Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The hardware can support any image size WxH,
with arbitrary W (image width) and H (image height) dimensions.
Align upwards buffer size for both encoder and decoder.
and leave the picture resolution unchanged.
For decoder, the risk of memory out of bounds can be avoided.
For both encoder and decoder, the driver will lift the limitation of
resolution alignment.
For example, the decoder can support jpeg whose resolution is 227x149
the encoder can support nv12 1080P, won't change it to 1920x1072.
Fixes: 2db16c6ed72ce ("media: imx-jpeg: Add V4L2 driver for i.MX8 JPEG Encoder/Decoder") Signed-off-by: Ming Qian <ming.qian@nxp.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To support dynamic resolution change,
driver should meet the following conditions:
1. the previous pictures are all decoded before source change event.
2. prevent decoding new resolution pictures with incorrect capture
buffer, until user handle source change event and setup capture.
3. report correct fmt and resolution during source change.
The decoder will save the precision that was detected from jpeg header
and use it later, when choosing the pixel format and also calculate
bytesperline according to precision.
The 12bit jpeg is not supported yet,
but driver shouldn't led to serious problem if user enqueue a 12 bit jpeg.
And the 12bit jpeg is supported by hardware, driver may support it later.
There is a hardware bug that it will load
the first 128 bytes of configuration data twice,
it will led to some configure error.
so shift the configuration data 128 bytes,
and make the first 128 bytes all zero,
then hardware will load the 128 zero twice,
and ignore them as garbage.
then the configuration data can be loaded correctly
the register CAST_NOMFRSIZE_LO should be equal to CAST_STATUS16
the register CAST_NOMFRSIZE_HI should be equal to CAST_STATUS17
the register CAST_OFBSIZE_LO should be equal to CAST_STATUS18
the register CAST_OFBSIZE_HI should be equal to CAST_STATUS19
We got the following warning when booting the kernel:
[ 3.243674] INFO: trying to register non-static key.
[ 3.243922] The code is fine but needs lockdep annotation, or maybe
[ 3.244230] you didn't initialize this object before use?
[ 3.245642] Call Trace:
[ 3.247836] lock_acquire+0xff/0x2d0
[ 3.248727] tw686x_audio_irq+0x1a5/0xcc0 [tw686x]
[ 3.249211] tw686x_irq+0x1f9/0x480 [tw686x]
The lock 'vc->qlock' will be initialized in tw686x_video_init(), but the
driver registers the irq before calling the tw686x_video_init(), and we
got the warning.
Fix this by registering the irq at the end of probe
Fixes: 704a84ccdbf1 ("[media] media: Support Intersil/Techwell TW686x-based video capture cards") Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The trailing semicolon causes a compiler error, so let's remove it.
net/ipv4/raw.c: In function ‘raw_icmp_error’:
net/ipv4/raw.c:266:2: error: ISO C90 forbids mixed declarations and code [-Werror=declaration-after-statement]
266 | struct hlist_nulls_head *hlist;
| ^~~~~~
Fixes: ba44f8182ec2 ("raw: use more conventional iterators") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using rwlock in networking code is extremely risky.
writers can starve if enough readers are constantly
grabing the rwlock.
I thought rwlock were at fault and sent this patch:
https://lkml.org/lkml/2022/6/17/272
But Peter and Linus essentially told me rwlock had to be unfair.
We need to get rid of rwlock in networking code.
Without this fix, following script triggers soft lockups:
for i in {1..48}
do
ping -f -n -q 127.0.0.1 &
sleep 0.1
done
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Blamed commit only dealt with applications issuing small writes.
Issue here is that we allow to force memory schedule for the sk_buff
allocation, but we have no guarantee that sendmsg() is able to
copy some payload in it.
In this patch, I make sure the socket can use up to tcp_wmem[0] bytes.
For example, if we consider tcp_wmem[0] = 4096 (default on x86),
and initial skb->truesize being 1280, tcp_sendmsg() is able to
copy up to 2816 bytes under memory pressure.
Before this patch a sendmsg() sending more than 2816 bytes
would either block forever (if persistent memory pressure),
or return -EAGAIN.
For bigger MTU networks, it is advised to increase tcp_wmem[0]
to avoid sending too small packets.
v2: deal with zero copy paths.
Fixes: 8e4d980ac215 ("tcp: fix behavior for epoll edge trigger") Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by: Wei Wang <weiwan@google.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver uses crypto hash functions so it needs to select CRYPTO_HASH.
This fixes build errors:
drivers/gpu/drm/bridge/ite-it6505.o: in function `it6505_hdcp_wait_ksv_list':
ite-it6505.c:(.text+0x4c26): undefined reference to `crypto_alloc_shash'
ite-it6505.c:(.text+0x4c6d): undefined reference to `crypto_shash_digest'
ite-it6505.c:(.text+0x4c7d): undefined reference to `crypto_destroy_tfm'
ite-it6505.c:(.text+0x4d69): undefined reference to `crypto_destroy_tfm'
This patch is similar to 7e193a42c37c ("can: netlink: allow
configuring of fixed bit rates without need for do_set_bittiming
callback") but for data bit rates instead of bit rates.
Usually CAN devices support configurable data bit rates. The limits
are defined by struct can_priv::data_bittiming_const. Another way is
to implement the struct can_priv::do_set_data_bittiming callback.
If the bit rate is configured via netlink, the can_changelink()
function checks that either can_priv::data_bittiming_const or struct
can_priv::do_set_data_bittiming is implemented.
In commit 431af779256c ("can: dev: add CAN interface API for fixed
bitrates") an API for configuring bit rates on CAN interfaces that
only support fixed bit rates was added. The supported bit rates are
defined by struct can_priv::bitrate_const.
However the above mentioned commit forgot to add the struct
can_priv::data_bitrate_const to the check in can_changelink().
In order to avoid to implement a no-op can_priv::do_set_data_bittiming
callback on devices with fixed data bit rates, extend the check in
can_changelink() accordingly.
Link: https://lore.kernel.org/all/20220613143633.4151884-1-mkl@pengutronix.de Fixes: 431af779256c ("can: dev: add CAN interface API for fixed bitrates") Acked-by: Max Staudt <max@enpas.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a copypasta error. The caller of compose_plane() already checks
primary_composer->map. In contrast, plane_composer->map is never
verified here before handling.
Usually CAN devices support configurable bit rates. The limits are
defined by struct can_priv::bittiming_const. Another way is to
implement the struct can_priv::do_set_bittiming callback.
If the bit rate is configured via netlink, the can_changelink()
function checks that either can_priv::bittiming_const or struct
can_priv::do_set_bittiming is implemented.
In commit 431af779256c ("can: dev: add CAN interface API for fixed
bitrates") an API for configuring bit rates on CAN interfaces that
only support fixed bit rates was added. The supported bit rates are
defined by struct can_priv::bitrate_const.
However the above mentioned commit forgot to add the struct
can_priv::bitrate_const to the check in can_changelink().
In order to avoid to implement a no-op can_priv::do_set_bittiming
callback on devices with fixed bit rates, extend the check in
can_changelink() accordingly.
Link: https://lore.kernel.org/all/20220611144248.3924903-1-mkl@pengutronix.de Fixes: 431af779256c ("can: dev: add CAN interface API for fixed bitrates") Reported-by: Max Staudt <max@enpas.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If sk->sk_forward_alloc is 150000, and we need to schedule 150001 bytes,
we want to allocate 1 byte more (rounded up to one page),
instead of 150001 :/
Commit 680532c50bca ("drm: adv7511: Add support for
i2c_new_secondary_device") allows a device tree node to override
the default addresses of the secondary i2c devices. This is useful
for solving address conflicts on the i2c bus.
In adv7511_init_cec_regmap() the new i2c address of cec device is
read from device tree and immediately accessed, well before it is
written in the proper register to override the default address.
This can cause an i2c error during probe and a consequent probe
failure.
Once the new i2c address is read from the device tree, override
the default address before any attempt to access the cec.
Tested with adv7533 and stm32mp157f.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com> Fixes: 680532c50bca ("drm: adv7511: Add support for i2c_new_secondary_device") Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220607213144.427177-1-antonio.borneo@foss.st.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since drm_prime_pages_to_sg() function return error pointers.
The drm_gem_shmem_get_sg_table() function returns error pointers too.
Using IS_ERR() to check the return value to fix this.
'cache_ent' could be set NULL inside virtio_gpu_cmd_get_capset()
and it will lead to a NULL dereference by a lately use of it
(i.e., ptr = cache_ent->caps_cache). Fix it with a NULL check.
NPCM can support up to 10 own slave addresses. In practice, only one
address is actually being used. In order to access addresses 2 and above,
need to switch register banks. The switch needs spinlock.
To avoid using spinlock for this useless feature removed support of SA >=
2. Also fix returned slave event enum.
Remove some comment since the bank selection is not required. The bank
selection is not required since the supported slave addresses are reduced.
Fixes: 56a1485b102e ("i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver") Signed-off-by: Tali Perry <tali.perry1@gmail.com> Signed-off-by: Tyrone Ting <kfting@nuvoton.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During device remove care needs to be taken that no work is pending
before it removes the underlying DRM bridge etc, but this can be done on
the specific work rather than waiting for the flush of the system-wide
workqueue.
Fixes: bc6fa8676ebb ("drm/bridge/lontium-lt9611uxc: move HPD notification out of IRQ handler") Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220601233818.1877963-1-bjorn.andersson@linaro.org Signed-off-by: Sasha Levin <sashal@kernel.org>
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: e67f6037ae1b ("drm/meson: split out encoder from meson_dw_hdmi") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220601033927.47814-3-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
of_graph_get_remote_node() returns remote device nodepointer with
refcount incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 318ba02cd8a8 ("drm/meson: encoder_cvbs: switch to bridge with ATTACH_NO_CONNECTOR") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220601033927.47814-2-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In the dsi_enable function, mtk_dsi_rxtx_control is to
pull up the MIPI signal operation. Before dsi_disable,
MIPI should also be pulled down by writing a register
instead of disabling dsi.
If disable dsi without pulling the mipi signal low, the value of
the register will still maintain the setting of the mipi signal being
pulled high.
After resume, even if the mipi signal is not pulled high, it will still
be in the high state.
In order to match the changes of "Use the drm_panel_bridge API",
the poweron/poweroff of dsi is extracted from enable/disable and
defined as new funcs (atomic_pre_enable/atomic_post_disable).
Since dsi_poweron is moved from dsi_enable to pre_enable function, in
order to avoid poweron failure, the operation of dsi register fails to
cause bus hang. Therefore, the protection mechanism is added to the
dsi_enable function.
Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API") Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-3-git-send-email-xinlei.lee@mediatek.com/ Signed-off-by: Jitao Shi <jitao.shi@mediatek.com> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com> Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The last case label can write two buffers 'mc_reg_address[j]' and
'mc_data[j]' with 'j' offset equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE
since there are no checks for this value in both case labels after the
last 'j++'.
Instead of changing '>' to '>=' there, add the bounds check at the start
of the second 'case' (the first one already has it).
Also, remove redundant last checks for 'j' index bigger than array size.
The expression is always false. Moreover, before or after the patch
'table->last' can be equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE and it
seems it can be a valid value.
Detected using the static analysis tool - Svace. Fixes: 69e0b57a91ad ("drm/radeon/kms: add dpm support for cayman (v5)") Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently when firmware recovery is in progress, we do not queue REO
commands to the firmware, instead -ESHUTDOWN will be returned to the
caller leading to a failure print on the console. The REO command in
the problem scenario is sent for all tids of a peer in which case we
will have 16 failure prints on the console for a single peer. For an
AP usecase, this count would be even higher in a worst case scenario.
Since these commands are bound to fail during firmware recovery, it
is better to avoid printing these failures and thereby avoid message
flooding on the console.
Currently a couple of debug_mask entries are mapped to the same value,
this could enable unintended driver logging. If enabling DP_TX logs was
the intention, then this could also enable PCI logs flooding the dmesg
buffer or vice versa. Fix this by correctly assigning the debug masks.
On htc_tx_completion error the skb is not dropped. This is wrong since
the completion_handler logic expect the skb to be consumed anyway even
when an error is triggered. Not freeing the skb on error is a memory
leak since the skb won't be freed anywere else. Correctly free the
packet on eid >= ATH11K_HTC_EP_COUNT before returning.
Fixes: f951380a6022 ("ath11k: Disabling credit flow for WMI path") Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220528142516.20819-2-ansuelsmth@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
tc_redirect_dtime was reported flaky from time to time. It
always fails at the udp test and complains about the bpf@tc-ingress
got a skb->tstamp when handling udp packet. It is unexpected
because the skb->tstamp should have been cleared when crossing
different netns.
The most likely cause is that the skb is actually a tcp packet
from the earlier tcp test. It could be the final TCP_FIN handling.
This patch tightens the skb->tstamp check in the bpf prog. It ensures
the skb is the current testing traffic. First, it checks that skb
matches the IPPROTO of the running test (i.e. tcp vs udp).
Second, it checks the server port (dst_ns_port). The server
port is unique for each test (50000 + test_enum).
Also fixed a typo in test_udp_dtime(): s/P100/P101/
Fixes: c803475fd8dd ("bpf: selftests: test skb->tstamp in redirect_neigh") Reported-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20220601234050.2572671-1-kafai@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In the commit da00d2f117a0 ("bpf: Add test ops for BPF_PROG_TYPE_TRACING"),
the bpf_fentry_test1 function was moved into bpf_prog_test_run_tracing(),
which is the test_run function of the tracing BPF programs.
Thus calling 'bpf_prog_test_run_opts(filter_fd, &topts)' will not trigger
bpf_fentry_test1 function as filter_fd is a sk_filter BPF program.
Fix it by replacing filter_fd with fexit_fd in the bpf_prog_test_run_opts()
function.
Fixes: da00d2f117a0 ("bpf: Add test ops for BPF_PROG_TYPE_TRACING") Signed-off-by: Yuntao Wang <ytcoode@gmail.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20220521151329.648013-1-ytcoode@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In __spi_validate, there's a validation that no partial transfers
are accepted (xfer->len % w_size must be zero). When
max_chunk is not a multiple of bpw (e.g. max_chunk = 65535,
bpw = 16), the transfer will be rejected.
This patch aligns max_chunk to 2 bytes (the maximum value of bpw is 16),
so that no partial transfer will occur.
Make sure to clear the IRQ affinity hint also on shutdown to avoid
triggering a WARN_ON_ONCE() in __free_irq() when stopping MHI while
using a single MSI vector.
Fixes: e94b07493da3 ("ath11k: Set IRQ affinity to CPU0 in case of one MSI vector") Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220523143258.24818-1-johan+linaro@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure to allocate resources needed before registering the device.
This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.
I did not see this issue with next-20220310, but I hit it on every probe
with next-20220511. Perhaps some timing changed in between.
For power-up sequence, WILC expects RESET set to high 5ms after making
chip_en(enable) so corrected chip power-up sequence by making RESET high.
For Power-Down sequence, the correct sequence make RESET and CHIP_EN low
without any extra delay.
Fixes: ec031ac4792c ("wilc1000: Add reset/enable GPIO support to SPI driver") Signed-off-by: Ajay Singh <ajay.kathat@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220524120606.9675-1-ajay.kathat@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the copy_from_user() fails or the user gives invalid date then the
correct thing to do is to return a negative error code. (Currently it
returns success).
I made a copy additional related cleanups:
1) There is no need to check "buffer" for NULL. That's handled by
copy_from_user().
2) The "h2c_len" variable cannot be negative because it is unsigned
and because sscanf() does not return negative error codes.
Fixes: 610247f46feb ("rtlwifi: Improve debugging by using debugfs") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/YoOLnDkHgVltyXK7@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
If CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20=y && CONFIG_DRM_DISPLAY_HELPER=m,
bulding fails:
drivers/gpu/drm/panel/panel-samsung-atna33xc20.o: In function `atana33xc20_probe':
panel-samsung-atna33xc20.c:(.text+0x744): undefined reference to
`drm_panel_dp_aux_backlight'
make: *** [vmlinux] Error 1
Let CONFIG_DRM_PANEL_SAMSUNG_ATNA33XC20 select DRM_DISPLAY_DP_HELPER and
CONFIG_DRM_DISPLAY_HELPER to fix this error.
Fixes: 32ce3b320343 ("drm/panel: atna33xc20: Introduce the Samsung ATNA33XC20 panel") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Gao Chao <gaochao49@huawei.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220524024551.539-1-gaochao49@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was
registered via OF. This means that the st7735r.ko module won't autoload if
a DT has a node with a compatible "okaya,rh128128t" string.
In that case, kmod expects a "MODALIAS=of:N*T*Cokaya,rh128128t" uevent but
instead will get a "MODALIAS=spi:rh128128t", which is not present in the
list of aliases:
In commit 19cf41b64e3b ("lontium-lt9611: check a different
register bit for HDMI sensing"), the bit flag used to detect
HDMI cable connect was switched from BIT(2) to BIT(0) to improve
compatibility with some monitors that didn't seem to set BIT(2).
However, with that change, I've seen occasional issues where the
detection failed, because BIT(2) was set, but not BIT(0).
Unfortunately, as I understand it, the bits and their function
was never clearly documented. So lets instead check both
(BIT(2) | BIT(0)) when checking the register.
Cc: Yongqin Liu <yongqin.liu@linaro.org> Cc: Amit Pundir <amit.pundir@linaro.org> Cc: Peter Collingbourne <pcc@google.com> Cc: Vinod Koul <vkoul@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Robert Foss <robert.foss@linaro.org> Cc: kernel-team@android.com Fixes: 19cf41b64e3b ("lontium-lt9611: check a different register bit for HDMI sensing") Signed-off-by: John Stultz <jstultz@google.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220511012612.3297577-2-jstultz@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge rising - but instead rely on Devicetree to configure it.
All Qualcomm DTSI with WCN3990 define the interrupt type as level high,
so the mismatch between DTSI and driver causes rebind issues:
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/unbind
$ echo 18800000.wifi > /sys/bus/platform/drivers/ath10k_snoc/bind
[ 44.763114] irq: type mismatch, failed to map hwirq-446 for interrupt-controller@17a00000!
[ 44.763130] ath10k_snoc 18800000.wifi: error -ENXIO: IRQ index 0 not found
[ 44.763140] ath10k_snoc 18800000.wifi: failed to initialize resource: -6
The Refclk may be supplied by SoC clock output instead of crystal
oscillator, make sure the clock are enabled before any other action
is performed with the bridge chip, otherwise it may either fail to
operate at all, or miss reset GPIO toggle.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Fixes: 7caff0fc4296e ("drm/bridge: tc358767: Add DPI to eDP bridge driver") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Marek Vasut <marex@denx.de> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Robert Foss <robert.foss@linaro.org> Cc: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Maxime Ripard <maxime@cerno.tech> Link: https://patchwork.freedesktop.org/patch/msgid/20220520121543.11550-1-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Only the first mode is
currently supported. In order to support the rest of the modes without
making the tc_probe() overly long, split the bridge endpoint parsing
into dedicated function, where the necessary logic to detect the bridge
mode based on which endpoints are connected, can be implemented.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Tested-by: Lucas Stach <l.stach@pengutronix.de> # In both DPI to eDP and DSI to DPI mode. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jonas Karlman <jonas@kwiboo.se> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Maxime Ripard <maxime@cerno.tech> Cc: Neil Armstrong <narmstrong@baylibre.com> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Robert Foss <robert.foss@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220329085015.39159-7-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
While working on the DP AUX bus code I found a few small things that
should be fixed. Namely the non-devm version of
of_dp_aux_populate_ep_devices() was missing an export. There was also
an extra blank line in a kerneldoc and a kerneldoc that incorrectly
documented a return value. Fix these.
of_find_device_by_node() takes reference, we should use put_device()
to release it when not need anymore.
Add missing put_device() in error path to avoid refcount
leak.
Fixes: 0af5e0b41110 ("drm/meson: encoder_hdmi: switch to bridge DRM_BRIDGE_ATTACH_NO_CONNECTOR") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220511054052.51981-1-linmq006@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
val = (u64)NSEC_PER_SEC * LPC18XX_PWM_TIMER_MAX;
do_div(val, lpc18xx_pwm->clk_rate);
lpc18xx_pwm->max_period_ns = val;
is bogus because with NSEC_PER_SEC = 1000000000,
LPC18XX_PWM_TIMER_MAX = 0xffffffff and clk_rate < NSEC_PER_SEC this
overflows the (on lpc18xx (i.e. ARM32) 32 bit wide) unsigned int
.max_period_ns. This results (dependant of the actual clk rate) in an
arbitrary limitation of the maximal period. E.g. for clkrate = 333333333 (Hz) we get max_period_ns = 9 instead of 12884901897.
So make .max_period_ns an u64 and pass period and duty as u64 to not
discard relevant digits. And also make use of mul_u64_u64_div_u64()
which prevents all overflows assuming clk_rate < NSEC_PER_SEC.
.apply() assumes the clk to be for a given PWM iff the PWM is enabled.
So make sure this is the case when .probe() completes. And in .remove()
disable the according number of times.
This fixes a clk enable/disable imbalance, if some PWMs are already running
at probe time.
Fixes: 9e37a53eb051 (pwm: sifive: Add a driver for SiFive SoC PWM) Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of explicitly using PWM_SIFIVE_PWMCMP0 + pwm->hwpwm *
PWM_SIFIVE_SIZE_PWMCMP for each access to one of the PWMCMP registers,
introduce a macro that takes the hwpwm id as parameter.
For the register definition using a plain 4 instead of the cpp constant
PWM_SIFIVE_SIZE_PWMCMP is easier to read, so define the offset macro
without the constant. The latter can then be dropped as there are no
users left.
Include sys/time.h and pthread.h in tmon.h, so that types
"pthread_mutex_t" and "struct timeval tv" are known when tmon.h
references them.
Without these headers, compiling tmon against musl-libc will fail with
these errors:
In file included from sysfs.c:31:0:
tmon.h:47:8: error: unknown type name 'pthread_mutex_t'
extern pthread_mutex_t input_lock;
^~~~~~~~~~~~~~~
make[3]: *** [<builtin>: sysfs.o] Error 1
make[3]: *** Waiting for unfinished jobs....
In file included from tui.c:31:0:
tmon.h:54:17: error: field 'tv' has incomplete type
struct timeval tv;
^~
make[3]: *** [<builtin>: tui.o] Error 1
make[2]: *** [Makefile:83: tmon] Error 2
Signed-off-by: Markus Mayer <mmayer@broadcom.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com> Acked-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Tested-by: Alejandro González <alejandro.gonzalez.correo@gmail.com> Fixes: 94f69966faf8 ("tools/thermal: Introduce tmon, a tool for thermal subsystem") Link: https://lore.kernel.org/r/20220718031040.44714-1-f.fainelli@gmail.com Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang has -Wconstant-conversion by default, and the constant 0xAAAAAAAAA
(9 As) being converted to an int, which is generally 32 bits, results
in the compile warning:
clang -Wl,-no-as-needed -Wall -isystem ../../../../usr/include/ -lpthread seccomp_bpf.c -lcap -o seccomp_bpf
seccomp_bpf.c:812:67: warning: implicit conversion from 'long' to 'int' changes value from 45812984490 to -1431655766 [-Wconstant-conversion]
int kill = kill_how == KILL_PROCESS ? SECCOMP_RET_KILL_PROCESS : 0xAAAAAAAAA;
~~~~ ^~~~~~~~~~~
1 warning generated.
-1431655766 is the expected truncation, 0xAAAAAAAA (8 As), so use
this directly in the code to avoid the warning.
The commit 8bb649ee1da3 ("io_uring: remove ring quiesce for
io_uring_register") removed the worklow relying on reinit/resurrection
of the percpu_ref, hence, initialization with that requested is a relic.
This is based on code review, this causes no real bug (and theoretically
can't). Technically it's a revert of commit 214828962dea ("io_uring:
initialize percpu refcounters using PERCU_REF_ALLOW_REINIT") but since
the flag omission is now justified, I'm not making this a revert.
Fixes: 8bb649ee1da3 ("io_uring: remove ring quiesce for io_uring_register") Signed-off-by: Michal Koutný <mkoutny@suse.com> Acked-by: Roman Gushchin <roman.gushchin@linux.dev> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Starting with FEAT_WFXT in ARMv8.7, the TI field in the ISS
that is reported on a WFx trap is expanded by one bit to
allow the description of WFET and WFIT.
Special care is taken to exclude the WFxT bit from the mask
used to match WFI so that it also matches WFIT when trapped from
EL0.
Add nvme_fc_io_getuuid() to the nvme-fc transport. The routine is invoked
by the FC LLDD on a per-I/O request basis. The routine translates from the
FC-specific request structure to the bio and the cgroup structure in order
to obtain the FC appid stored in the cgroup structure. If a value is not
set or a bio is not found, a NULL appid (aka uuid) will be returned to the
LLDD.
Link: https://lore.kernel.org/r/20220519123110.17361-2-jsmart2021@gmail.com Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Acked-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Muneendra Kumar <muneendra.kumar@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In preparation for splitting io_uring up a bit, move it into its own
top level directory. It didn't really belong in fs/ anyway, as it's
not a file system only API.
This adds io_uring/ and moves the core files in there, and updates the
MAINTAINERS file for the new location.
On Fri, Jun 17, 2022 at 02:08:52PM +0300, Stephane Eranian wrote:
> Some changes to the way invalid MSR accesses are reported by the
> kernel is causing some problems with messages printed on the
> console.
>
> We have seen several cases of ex_handler_msr() printing invalid MSR
> accesses once but the callstack multiple times causing confusion on
> the console.
> The problem here is that another earlier commit (5.13):
>
> a358f40600b3 ("once: implement DO_ONCE_LITE for non-fast-path "do once" functionality")
>
> Modifies all the pr_*_once() calls to always return true claiming
> that no caller is ever checking the return value of the functions.
>
> This is why we are seeing the callstack printed without the
> associated printk() msg.
Extract the ONCE_IF(cond) part into __ONCE_LTE_IF() and use that to
implement DO_ONCE_LITE_IF() and fix the extable code.
dequeue_task_rt() only decrements 'rt_rq->rt_nr_running' after having
called sched_update_tick_dependency() preventing it from re-enabling the
tick on systems that no longer have pending SCHED_RT tasks but have
multiple runnable SCHED_OTHER tasks:
Every other scheduler class performs the operation in the opposite
order, and sched_update_tick_dependency() expects the values to be
updated as such. So avoid the misbehaviour by inverting the order in
which the above operations are performed in the RT scheduler.
Fixes: 76d92ac305f2 ("sched: Migrate sched to use new tick dependency mask model") Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <vschneid@redhat.com> Reviewed-by: Phil Auld <pauld@redhat.com> Link: https://lore.kernel.org/r/20220628092259.330171-1-nsaenzju@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The arm_spe_pmu driver will enable SYS_PMSCR_EL1.CX in order to add CONTEXT
packets into the traces, if the owner of the perf event runs with required
capabilities i.e CAP_PERFMON or CAP_SYS_ADMIN via perfmon_capable() helper.
The value of this bit is computed in the arm_spe_event_to_pmscr() function
but the check for capabilities happens in the pmu event init callback i.e
arm_spe_pmu_event_init(). This suggests that the value of the CX bit should
remain consistent for the duration of the perf session.
However, the function arm_spe_event_to_pmscr() may be called later during
the event start callback i.e arm_spe_pmu_start() when the "current" process
is not the owner of the perf session, hence the CX bit setting is currently
not consistent.
One way to fix this, is by caching the required value of the CX bit during
the initialization of the PMU event, so that it remains consistent for the
duration of the session. It uses currently unused 'event->hw.flags' element
to cache perfmon_capable() value, which can be referred during event start
callback to compute SYS_PMSCR_EL1.CX. This ensures consistent availability
of context packets in the trace as per event owner capabilities.
Drop BIT(SYS_PMSCR_EL1_CX_SHIFT) check in arm_spe_pmu_event_init(), because
now CX bit cannot be set in arm_spe_event_to_pmscr() with perfmon_capable()
disabled.
Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Alexey Budankov <alexey.budankov@linux.intel.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Fixes: d5d9696b0380 ("drivers/perf: Add support for ARMv8.2 Statistical Profiling Extension") Reported-by: German Gomez <german.gomez@arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20220714061302.2715102-1-anshuman.khandual@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pmu_sbi_setup_irqs(), we should call of_node_put() for the 'cpu'
when breaking out of for_each_of_cput_node() as its refcount will
be automatically increased and decreased during the iteration.
Fixes: 4905ec2fb7e6 ("RISC-V: Add sscofpmf extension support") Signed-off-by: Liang He <windhl@126.com> Reviewed-by: Atish Patra <atishp@rivosinc.com> Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Link: https://lore.kernel.org/r/20220715130330.443363-1-windhl@126.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using a NOMAP domain, __irq_resolve_mapping() doesn't store
the Linux IRQ number at the address optionally provided by the caller.
While this isn't a huge deal (the returned value is guaranteed
to the hwirq that was passed as a parameter), let's honour the letter
of the API by writing the expected value.
The remoteproc configuration in qcom-msm8974.dtsi is incomplete because
it lacks the regulator supplies that should be added in the board DT
files. Some of the msm8974 boards are currently missing the regulator
supplies and should have the remoteprocs disabled to avoid making use
of the incomplete configuration.
This also fixes dtbs_check warnings after moving "qcom,msm8974-mss-pil"
to DT schema, which rightfully complains that the -supply properties
are missing for some boards:
qcom-apq8074-dragonboard.dtb:
remoteproc@fc880000: 'pll-supply' is a required property
From schema: remoteproc/qcom,msm8916-mss-pil.yaml
remoteproc@fc880000: 'mss-supply' is a required property
From schema: remoteproc/qcom,msm8916-mss-pil.yaml
remoteproc@fc880000: 'oneOf' conditional failed, one must be fixed:
'power-domains' is a required property
'power-domain-names' is a required property, or
'cx-supply' is a required property
'mx-supply' is a required property
Cc: Luca Weiss <luca@z3ntu.xyz> Cc: Konrad Dybcio <konrad.dybcio@somainline.org> Fixes: f300826d27be ("ARM: dts: qcom-msm8974: Sort and clean up nodes") Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220712124421.3129206-4-stephan.gerhold@kernkonzept.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
