gcc's -freorder-blocks-and-partition option makes it group frequently
and infrequently used code in .text.hot and .text.unlikely sections
respectively. At least when building modules on s390, this option is
used by default.
gdb assumes that all code is located in .text section, and that .text
section is located at module load address. With such modules this is no
longer the case: there is code in .text.hot and .text.unlikely, and
either of them might precede .text.
Fix by explicitly telling gdb the addresses of code sections.
It might be tempting to do this for all sections, not only the ones in
the white list. Unfortunately, gdb appears to have an issue, when
telling it about e.g. loadable .note.gnu.build-id section causes it to
think that non-loadable .note.Linux section is loaded at address 0,
which in turn causes NULL pointers to be resolved to bogus symbols. So
keep using the white list approach for the time being.
The MAP_HUGETLB ("-H" option) of gup_benchmark fails:
$ sudo ./gup_benchmark -H
mmap: Invalid argument
This is because gup_benchmark.c is passing in a file descriptor to
mmap(), but the fd came from opening up the /dev/zero file. This
confuses the mmap syscall implementation, which thinks that, if the
caller did not specify MAP_ANONYMOUS, then the file must be a huge page
file. So it attempts to verify that the file really is a huge page
file, as you can see here:
ksys_mmap_pgoff()
{
if (!(flags & MAP_ANONYMOUS)) {
retval = -EINVAL;
if (unlikely(flags & MAP_HUGETLB && !is_file_hugepages(file)))
goto out_fput; /* THIS IS WHERE WE END UP */
else if (flags & MAP_HUGETLB) {
...proceed normally, /dev/zero is ok here...
...and of course is_file_hugepages() returns "false" for the /dev/zero
file.
The problem is that the user space program, gup_benchmark.c, really just
wants anonymous memory here. The simplest way to get that is to pass
MAP_ANONYMOUS whenever MAP_HUGETLB is specified, so that's what this
patch does.
Link: http://lkml.kernel.org/r/20191021212435.398153-2-jhubbard@nvidia.com Signed-off-by: John Hubbard <jhubbard@nvidia.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Jérôme Glisse <jglisse@redhat.com> Cc: Keith Busch <keith.busch@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using the example SOF amp widget topology, KASAN dumps this
when the AMP bytes kcontrol gets loaded:
[ 9.579548] BUG: KASAN: slab-out-of-bounds in
sof_control_load+0x8cc/0xac0 [snd_sof]
[ 9.588194] Write of size 40 at addr ffff8882314559dc by task
systemd-udevd/2411
Fix that by rejecting the topology if the bytes data size > max_size
Fixes: 311ce4fe7637d ("ASoC: SOF: Add support for loading topologies") Reviewed-by: Jaska Uimonen <jaska.uimonen@intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Signed-off-by: Dragos Tarcatu <dragos_tarcatu@mentor.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20191106145816.9367-1-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Split the 10Kbytes CAN message RAM to be able to use simultaneously
FDCAN1 and FDCAN2 instances.
First 5Kbytes are allocated to FDCAN1 and last 5Kbytes are used for
FDCAN2. To do so, set the offset to 0x1400 in mram-cfg for FDCAN2.
The bd70528 watchdog driver is probed by MFD driver. Add MODULE_ALIAS
in order to allow udev to load the module when MFD sub-device cell for
watchdog is added.
Fixes: bbc88a0ec9f37 ("watchdog: bd70528: Initial support for ROHM BD70528 watchdog block") Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
SCU firmware calculates pretimeout based on current time stamp
instead of watchdog timeout stamp, need to convert the pretimeout
to SCU firmware's timeout value.
The left time value is wrong when we get it by sysfs. The left time value
should be equal to preset timeout value minus elapsed time value. According
to the Meson-GXB/GXL datasheets which can be found at [0], the timeout value
is saved to BIT[0-15] of the WATCHDOG_TCNT, and elapsed time value is saved
to BIT[16-31] of the WATCHDOG_TCNT.
nvme_mpath_clear_ctrl_paths() iterates through
the ctrl->namespaces list while holding ctrl->scan_lock.
This does not seem to be the correct way of protecting
from concurrent list modification.
Specifically, nvme_scan_work() sorts ctrl->namespaces
AFTER unlocking scan_lock.
This may result in the following (rare) crash in ctrl disconnect
during scan_work:
Fix:
After taking scan_lock in nvme_mpath_clear_ctrl_paths()
down_read(&ctrl->namespaces_rwsem) as well to make list traversal safe.
This will not cause deadlocks because taking scan_lock never happens
while holding the namespaces_rwsem.
Moreover, scan work downs namespaces_rwsem in the same order.
Alternative: sort ctrl->namespaces in nvme_scan_work()
while still holding the scan_lock.
This would leave nvme_mpath_clear_ctrl_paths() without correct protection
against ctrl->namespaces modification by anyone other than scan_work.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Anton Eidelman <anton@lightbitslabs.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case there are controllers that are not associated with any RDMA
device (e.g. during unsuccessful reconnection) and the user will unload
the module, these controllers will not be freed and will access already
freed memory. The same logic appears in other fabric drivers as well.
Fixes: 87fd125344d6 ("nvme-rdma: remove redundant reference between ib_device and tagset") Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Max Gurtovoy <maxg@mellanox.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of calling a useless (and broken) helper function to get the
next event of a tep event array, just get the array directly and iterate
over it.
Note, the broken part was from trace_find_next_event() which after this
will no longer be used, and can be removed.
Committer notes:
This fixes a segfault when generating python scripts from perf.data
files with multiple tracepoint events, i.e. the following use case is
fixed by this patch:
# perf record -e sched:* sleep 1
[ perf record: Woken up 31 times to write data ]
[ perf record: Captured and wrote 0.031 MB perf.data (9 samples) ]
# perf script -g python
Segmentation fault (core dumped)
#
Reported-by: Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Tzvetomir Stoyanov <tstoyanov@vmware.com> Cc: linux-trace-devel@vger.kernel.org Link: http://lkml.kernel.org/r/20191017153733.630cd5eb@gandalf.local.home Link: http://lore.kernel.org/lkml/20191017210636.061448713@goodmis.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The introduction of clocksource_tsc_early broke the functionality of
"tsc=reliable" and "tsc=nowatchdog" command line parameters, since
clocksource_tsc_early is unconditionally registered with
CLOCK_SOURCE_MUST_VERIFY and thus put on the watchdog list.
This can cause the TSC to be declared unstable during boot:
clocksource: timekeeping watchdog on CPU0: Marking clocksource
'tsc-early' as unstable because the skew is too large:
clocksource: 'refined-jiffies' wd_now: fffb7018 wd_last: fffb6e9d
mask: ffffffff
clocksource: 'tsc-early' cs_now: 68a6a7070f6a0 cs_last: 68a69ab6f74d6
mask: ffffffffffffffff
tsc: Marking TSC unstable due to clocksource watchdog
The corresponding elapsed times are cs_nsec=1224152026 and wd_nsec=378942392, so
the watchdog differs from TSC by 0.84 seconds.
This happens when HPET is not available and jiffies are used as the TSC
watchdog instead and the jiffies update is not happening due to lost timer
interrupts in periodic mode, which can happen e.g. with expensive debug
mechanisms enabled or under massive overload conditions in virtualized
environments.
Before the introduction of the early TSC clocksource the command line
parameters "tsc=reliable" and "tsc=nowatchdog" could be used to work around
this issue.
Restore the behaviour by disabling the watchdog if requested on the kernel
command line.
[ tglx: Clarify changelog ]
Fixes: aa83c45762a24 ("x86/tsc: Introduce early tsc clocksource") Signed-off-by: Michael Zhivich <mzhivich@akamai.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lkml.kernel.org/r/20191024175945.14338-1-mzhivich@akamai.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading") Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading") Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
When doing cat /proc/<PID>/stack, the output is missing the first entry.
When the current code walks the stack starting in stack_trace_save_tsk,
it skips all scheduler functions (that's OK) plus one more function. But
this one function should be skipped only for the 'current' task as it is
stack_trace_save_tsk proper.
The original code (before the common infrastructure) skipped one
function only for the 'current' task -- see save_stack_trace_tsk before 3599fe12a125. So do so also in the new infrastructure now.
Fixes: 214d8ca6ee85 ("stacktrace: Provide common infrastructure") Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Michal Suchanek <msuchanek@suse.de> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Link: https://lkml.kernel.org/r/20191030072545.19462-1-jslaby@suse.cz Signed-off-by: Sasha Levin <sashal@kernel.org>
Userspace never includes the NFT_BASE_CHAIN flag, this flag is inferred
from the NFTA_CHAIN_HOOK atribute. The chain update path does not allow
to update flags at this stage, the existing sanity check bogusly hits
EOPNOTSUPP in the basechain case if the offload flag is set on.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since v5.2 (commit "netlink: re-add parse/validate functions in strict
mode") NL_VALIDATE_STRICT is enabled. Fix the ipset nla_policies which did
not support strict mode and convert from deprecated parsings to verified ones.
Commit 3d8598fb9c5a ("clk: ti: clkctrl: use fallback udelay approach if
timekeeping is suspended") added handling for cases when timekeeping is
suspended. But looks like we can still get occasional "failed to enable"
errors on the PM runtime resume path with udelay() returning faster than
expected.
With ti-sysc interconnect target module driver this leads into device
failure with PM runtime failing with "failed to enable" clkctrl error.
Let's fix the issue with a delay of two times the desired delay as in
often done for udelay() to account for the inaccuracy.
Fixes: 3d8598fb9c5a ("clk: ti: clkctrl: use fallback udelay approach if timekeeping is suspended") Cc: Keerthy <j-keerthy@ti.com> Cc: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lkml.kernel.org/r/20190930154001.46581-1-tony@atomide.com Tested-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When ASoC card instance is removed containing a HDA codec,
hdac_hda_codec_remove() may run in parallel with codec resume.
This will cause problems if the HDA link is freed with
snd_hdac_ext_bus_link_put() while the codec is still in
middle of its resume process.
To fix this, change the order such that pm_runtime_disable()
is called before the link is freed. This will ensure any
pending runtime PM action is completed before proceeding
to free the link.
This issue can be easily hit with e.g. SOF driver by loading and
unloading the drivers.
When the compiler decides not to inline the Chunky-to-Planar core
functions, the build fails with:
c2p_planar.c:(.text+0xd6): undefined reference to `c2p_unsupported'
c2p_planar.c:(.text+0x1dc): undefined reference to `c2p_unsupported'
c2p_iplan2.c:(.text+0xc4): undefined reference to `c2p_unsupported'
c2p_iplan2.c:(.text+0x150): undefined reference to `c2p_unsupported'
Fix this by marking the functions __always_inline.
While this could be triggered before by manually enabling both
CONFIG_OPTIMIZE_INLINING and CONFIG_CC_OPTIMIZE_FOR_SIZE, it was exposed
in the m68k defconfig by commit ac7c3e4ff401b304 ("compiler: enable
CONFIG_OPTIMIZE_INLINING forcibly").
Fixes: 9012d011660ea5cf ("compiler: allow all arches to enable CONFIG_OPTIMIZE_INLINING") Reported-by: noreply@ellerman.id.au Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20190927094708.11563-1-geert@linux-m68k.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The GPIO handle is referencing the wrong GPIO, so the voltage did not
actually change as intended. The pinmux is already correct, so just
correct the GPIO number.
When a mon group is being deleted, rdtgrp->flags is set to RDT_DELETED
in rdtgroup_rmdir_mon() firstly. The structure of rdtgrp will be freed
until rdtgrp->waitcount is dropped to 0 in rdtgroup_kn_unlock() later.
During the window of deleting a mon group, if an application calls
rdtgroup_mondata_show() to read mondata under this mon group,
'rdtgrp' returned from rdtgroup_kn_lock_live() is a NULL pointer when
rdtgrp->flags is RDT_DELETED. And then 'rdtgrp' is passed in this path:
rdtgroup_mondata_show() --> mon_event_read() --> mon_event_count().
Thus it results in NULL pointer dereference in mon_event_count().
Check 'rdtgrp' in rdtgroup_mondata_show(), and return -ENOENT
immediately when reading mondata during the window of deleting a mon
group.
Attempting to allocate an entry at 0xffffffff when one is already
present would succeed in allocating one at 2^32, which would confuse
everything. Return -ENOSPC in this case, as expected.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there is an entry at INT_MAX then idr_for_each_entry() will increment
id after handling it. This is undefined behaviour, and is caught by
UBSAN. Adding 1U to id forces the operation to be carried out as an
unsigned addition which (when assigned to id) will result in INT_MIN.
Since there is never an entry stored at INT_MIN, idr_get_next() will
return NULL, ending the loop as expected.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 5c089fd0c734 ("idr: Fix idr_get_next race with idr_remove")
neglected to fix idr_get_next_ul(). As far as I can tell, nobody's
actually using this interface under the RCU read lock, but fix it now
before anybody decides to use it.
Fixes: 5c089fd0c734 ("idr: Fix idr_get_next race with idr_remove") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We have seen many crashes on powerpc hosts while loading bpf programs.
The problem here is that bpf_int_jit_compile() does a first pass
to compute the program length.
Then it allocates memory to store the generated program and
calls bpf_jit_build_body() a second time (and a third time
later)
What I have observed is that the second bpf_jit_build_body()
could end up using few more words than expected.
If bpf_jit_binary_alloc() put the space for the program
at the end of the allocated page, we then write on
a non mapped memory.
It appears that bpf_jit_emit_tail_call() calls
bpf_jit_emit_common_epilogue() while ctx->seen might not
be stable.
Only after the second pass we can be sure ctx->seen wont be changed.
Trying to avoid a second pass seems quite complex and probably
not worth it.
Fixes: ce0761419faef ("powerpc/bpf: Implement support for tail calls") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com> Cc: Sandipan Das <sandipan@linux.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Martin KaFai Lau <kafai@fb.com> Cc: Song Liu <songliubraving@fb.com> Cc: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20191101033444.143741-1-edumazet@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The functions bpf_map_area_alloc() and bpf_map_charge_init() prior
this commit passed the size parameter as size_t. In this commit this
is changed to u64.
All users of these functions avoid size_t overflows on 32-bit systems,
by explicitly using u64 when calculating the allocation size and
memory charge cost. However, since the result was narrowed by the
size_t when passing size and cost to the functions, the overflow
handling was in vain.
Instead of changing all call sites to size_t and handle overflow at
the call site, the parameter is changed to u64 and checked in the
functions above.
Fixes: d407bd25a204 ("bpf: don't trigger OOM killer under pressure with map alloc") Fixes: c85d69135a91 ("bpf: move memory size checks to bpf_map_charge_init()") Signed-off-by: Björn Töpel <bjorn.topel@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com> Link: https://lore.kernel.org/bpf/20191029154307.23053-1-bjorn.topel@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
"ctx:file_pos sysctl:read read ok narrow" works on s390 by accident: it
reads the wrong byte, which happens to have the expected value of 0.
Improve the test by seeking to the 4th byte and expecting 4 instead of
0.
This makes the latent problem apparent: the test attempts to read the
first byte of bpf_sysctl.file_pos, assuming this is the least-significant
byte, which is not the case on big-endian machines: a non-zero offset is
needed.
The point of the test is to verify narrow loads, so we cannot cheat our
way out by simply using BPF_W. The existence of the test means that such
loads have to be supported, most likely because llvm can generate them.
Fix the test by adding a big-endian variant, which uses an offset to
access the least-significant byte of bpf_sysctl.file_pos.
This reveals the final problem: verifier rejects accesses to bpf_sysctl
fields with offset > 0. Such accesses are already allowed for a wide
range of structs: __sk_buff, bpf_sock_addr and sk_msg_md to name a few.
Extend this support to bpf_sysctl by using bpf_ctx_range instead of
offsetof when matching field offsets.
Fixes: 7b146cebe30c ("bpf: Sysctl hook") Fixes: e1550bfe0de4 ("bpf: Add file_pos field to bpf_sysctl ctx") Fixes: 9a1027e52535 ("selftests/bpf: Test file_pos field in bpf_sysctl ctx") Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Andrey Ignatov <rdna@fb.com> Acked-by: Andrii Nakryiko <andriin@fb.com> Link: https://lore.kernel.org/bpf/20191028122902.9763-1-iii@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The zero'ing of bits 16 and 18 is incorrect. Currently the code
is masking with the bitwise-and of BIT(16) & BIT(18) which is
0, so the updated value for val is always zero. Fix this by bitwise
and-ing value with the correct mask that will zero bits 16 and 18.
Addresses-Coverity: (" Suspicious &= or |= constant expression") Fixes: b8eb71dcdd08 ("clk: sunxi-ng: Add A80 CCU") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
r375326 in Clang exposes an issue with operator precedence in
sunxi_div_clk_setup:
drivers/clk/sunxi/clk-sunxi.c:1083:30: warning: operator '?:' has lower
precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
data->div[i].critical ?
~~~~~~~~~~~~~~~~~~~~~ ^
drivers/clk/sunxi/clk-sunxi.c:1083:30: note: place parentheses around
the '|' expression to silence this warning
data->div[i].critical ?
^
)
drivers/clk/sunxi/clk-sunxi.c:1083:30: note: place parentheses around
the '?:' expression to evaluate it first
data->div[i].critical ?
^
(
1 warning generated.
It appears that the intention was for ?: to be evaluated first so that
CLK_IS_CRITICAL could be added to clkflags if the critical boolean was
set; right now, | is being evaluated first. Add parentheses around the
?: block to have it be evaluated first.
Fixes: 9919d44ff297 ("clk: sunxi: Use CLK_IS_CRITICAL flag for critical clks") Link: https://github.com/ClangBuiltLinux/linux/issues/745 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Maxime Ripard <mripard@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not allowed to sleep to early in the boot process and this may lead
to kernel issues if the bootloader didn't prepare the slow clock and main
clock.
This results in the following error and dump stack on the AriettaG25:
bad: scheduling from the idle thread!
Ensure it is possible to sleep, else simply have a delay.
max98090 spec states that chip needs to be in turned-on state to supply
mic bias. Enable SHDN dapm widget along with MICBIAS widget to
actually turn on mic bias for proper headset button detection.
This is similar to cht_ti_jack_event in
sound/soc/intel/boards/cht_bsw_max98090_ti.c.
Note that due to ts3a227e reports the jack event right away before the
notifier is registered, if headset is plugged on boot, headset button
will not get detected until headset is unplugged and plugged. This is
still an issue to be fixed.
When non standard names are used it is possible that one of the directions
are not provided, thus the flags needs to be present to tell the core that
we have half duplex setup.
Fixes: 642aafea8889 ("ASoC: ti: remove compat dma probing") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Link: https://lore.kernel.org/r/20191028115207.5142-1-peter.ujfalusi@ti.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MMA8451 interrupt triggers as low level, so the GPIO6_IO31 pin
needs to activate its pull up, otherwise it will stay always at low level
generating multiple interrupts.
The current device tree does not configure the IOMUX for this pin, so
it uses whathever comes configured from the bootloader.
The IOMUXC_SW_PAD_CTL_PAD_EIM_BCLK register value comes as 0x8000 from
the bootloader, which has PKE bit cleared, hence disabling the
pull-up.
Instead of relying on a previous configuration from the bootloader,
configure the GPIO6_IO31 pin with pull-up enabled in order to fix
this problem.
Keeping the IRQ chip definition static shares it with multiple instances
of the GPIO chip in the system. This is bad and now we get this warning
from GPIO library:
"detected irqchip that is shared with multiple gpiochips: please fix the driver."
Hence, move the IRQ chip definition from being driver static into the struct
intel_pinctrl. So a unique IRQ chip is used for each GPIO chip instance.
This patch is heavily based on the attachment to the bug by Christoph Marz.
Properly save and restore all top PLL related configuration registers
during suspend/resume cycle. So far driver only handled EPLL and RPLL
clocks, all other were reset to default values after suspend/resume cycle.
This caused for example lower G3D (MALI Panfrost) performance after system
resume, even if performance governor has been selected.
Reported-by: Reported-by: Marian Mihailescu <mihailescu2m@gmail.com> Fixes: 773424326b51 ("clk: samsung: exynos5420: add more registers to restore list") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The I2C multiplexer used on ls1028aqds is PCA9547, not PCA9847.
If the wrong compatible was used, this chip will not be able to
be probed correctly and hence fail to work.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com> Acked-by: Li Yang <leoyang.li@nxp.com> Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC") Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devm conversion of kirkwood was incorrect; on removal, devm takes
effect after the "remove" function has returned. So, the effect of
the conversion was to change the order during remove from:
- clk_disable_unprepare() - while the device may still be active
- snd_soc_unregister_component()
- cleanup resources
Hence, it introduces a bug, where the internal clock for the device
may be shut down before the device itself has been shut down. It is
known that Marvell SoCs, including Dove, locks up if registers for a
peripheral that has its clocks disabled are accessed.
Fixes: f98fc0f8154e ("ASoC: kirkwood: replace platform to component") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1iNGyP-0004oN-BA@rmk-PC.armlinux.org.uk Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When our call to get the external clock fails, we forget to clean up
the enabled internal clock correctly. Enable the clock after we have
obtained all our resources.
Fixes: 84aac6c79bfd ("ASoC: kirkwood: fix loss of external clock at probe time") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/E1iNGyK-0004oF-6A@rmk-PC.armlinux.org.uk Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
G3D clocks require special handling of their parent bus clock during power
domain on/off sequences. Those clocks were not initially added to the
sub-CMU handler, because that time there was no open-source driver for the
G3D (MALI Panfrost) hardware module and it was not possible to test it.
This patch fixes this issue. Parent clock for G3D hardware block is now
properly preserved during G3D power domain on/off sequence. This restores
proper MALI Panfrost performance broken by commit 8686764fc071
("ARM: dts: exynos: Add G3D power domain to Exynos542x").
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com> Fixes: b06a532bf1fa ("clk: samsung: Add Exynos5 sub-CMU clock driver") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marian Mihailescu <mihailescu2m@gmail.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocated for 'struct reset_control_array' in
of_reset_control_array_get() is never freed in
reset_control_array_put() resulting in kmemleak showing
the following backtrace.
Fixes: 17c82e206d2a ("reset: Add APIs to manage array of resets") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to the PM8916 Hardware Register Description,
CDC_D_CDC_CONN_HPHR_DAC_CTL has only a single bit (RX_SEL)
to switch between RX1 (0) and RX2 (1). It is not possible to
disable it entirely to achieve the "ZERO" state.
However, at the moment the "RDAC2 MUX" mixer defines three possible
values ("ZERO", "RX2" and "RX1"). Setting the mixer to "ZERO"
actually configures it to RX1. Setting the mixer to "RX1" has
(seemingly) no effect.
Remove "ZERO" and replace it with "RX1" to fix this.
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec") Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20191020153007.206070-1-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. Use cdns->pcm.num_in instead of stream_num_in for consistency with
the rest of the code. This was not detected earlier since platforms did
not have input-only PDIs.
2. use the correct offset for bi-dir PDM, based on IN and OUT
PDIs. Again this was not detected since PDM was not supported earlier.
When timer_of_init fails, it cleans up after itself by undoing
everything it did during the initialization function.
mtk_syst_init and mtk_gpt_init both call timer_of_cleanup if
timer_of_init fails. timer_of_cleanup try to release the resource
taken. Since these resources have already been cleaned up by
timer_of_init, we end up getting a few warnings printed:
When lockdep is enabled, plugging Thunderbolt dock on Dominik's laptop
triggers following splat:
======================================================
WARNING: possible circular locking dependency detected
5.3.0-rc6+ #1 Tainted: G T
------------------------------------------------------
pool-/usr/lib/b/1258 is trying to acquire lock: 000000005ab0ad43 (pci_rescan_remove_lock){+.+.}, at: authorized_store+0xe8/0x210
but task is already holding lock: 00000000bfb796b5 (&tb->lock){+.+.}, at: authorized_store+0x7c/0x210
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&tb->lock);
lock(pci_rescan_remove_lock);
lock(&tb->lock);
lock(pci_rescan_remove_lock);
stack backtrace:
CPU: 0 PID: 1258 Comm: pool-/usr/lib/b Tainted: G T 5.3.0-rc6+ #1
On an system using ACPI hotplug the host router gets hotplugged first and then
the firmware starts sending notifications about connected devices so the above
scenario should not happen in reality. However, after taking a second
look at commit a03e828915c0 ("thunderbolt: Serialize PCIe tunnel
creation with PCI rescan") that introduced the locking, I don't think it
is actually correct. It may have cured the symptom but probably the real
root cause was somewhere closer to PCI stack and possibly is already
fixed with recent kernels. I also tried to reproduce the original issue
with the commit reverted but could not.
So to keep lockdep happy and the code bit less complex drop calls to
pci_lock_rescan_remove()/pci_unlock_rescan_remove() in
tb_switch_set_authorized() effectively reverting a03e828915c0.
When we discover existing DP tunnels the code checks whether DP IN
adapter port is enabled by calling tb_dp_port_is_enabled() before it
continues the discovery process. On Light Ridge (gen 1) controller
reading only the first dword of the DP IN config space causes subsequent
access to the same DP IN port path config space to fail or return
invalid data as can be seen in the below splat:
If both DP In adapter config dwords are read in one go the issue does
not reproduce. This is likely firmware bug but we can work it around by
always reading the two dwords in one go. There should be no harm for
other controllers either so can do it unconditionally.
The prescaler mask for sam9x60 must be 0xff (8 bits).
Being set to 0, means that we cannot set any prescaler, thus the
programmable clocks do not work (except the case with prescaler 0)
Set the mask accordingly in layout struct.
Fixes: 01e2113de9a5 ("clk: at91: add sam9x60 pmc driver") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lkml.kernel.org/r/1569321191-27606-1-git-send-email-eugen.hristev@microchip.com Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The meson-saradc driver manually sets the input clock for
sar_adc_clk_sel. Update the GXBB clock driver (which is used on GXBB,
GXL and GXM) so the rate settings on sar_adc_clk_div are propagated up
to sar_adc_clk_sel which will let the common clock framework select the
best matching parent clock if we want that.
This makes sar_adc_clk_div consistent with the axg-aoclk and g12a-aoclk
drivers, which both also specify CLK_SET_RATE_PARENT.
Fixes: 33d0fcdfe0e870 ("clk: gxbb: add the SAR ADC clocks and expose them") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If there is only a single entry at 0, the first time we call xas_next(),
we return the entry. Unfortunately, all subsequent times we call
xas_next(), we also return the entry at 0 instead of noticing that the
xa_index is now greater than zero. This broke find_get_pages_contig().
Fixes: 64d3e9a9e0cc ("xarray: Step through an XArray") Reported-by: Kent Overstreet <kent.overstreet@gmail.com> Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only io_uring uses (and added) these, and we want to disallow the
use of sendmsg/recvmsg for anything but regular data transfers.
Use the newly added prep helper to split the msghdr copy out from
the core function, to check for msg_control and msg_controllen
settings. If either is set, we return -EINVAL.
Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is in preparation for enabling the io_uring helpers for sendmsg
and recvmsg to first copy the header for validation before continuing
with the operation.
There should be no functional changes in this patch.
Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we don't inherit the original task creds, then we can confuse users
like fuse that pass creds in the request header. See link below on
identical aio issue.
On some systems that are vulnerable to Spectre v2, it is up to
software to flush the link stack (return address stack), in order to
protect against Spectre-RSB.
When exiting from a guest we do some house keeping and then
potentially exit to C code which is several stack frames deep in the
host kernel. We will then execute a series of returns without
preceeding calls, opening up the possiblity that the guest could have
poisoned the link stack, and direct speculative execution of the host
to a gadget of some sort.
To prevent this we add a flush of the link stack on exit from a guest.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit ee13cb249fab ("powerpc/64s: Add support for software count
cache flush"), I added support for software to flush the count
cache (indirect branch cache) on context switch if firmware told us
that was the required mitigation for Spectre v2.
As part of that code we also added a software flush of the link
stack (return address stack), which protects against Spectre-RSB
between user processes.
That is all correct for CPUs that activate that mitigation, which is
currently Power9 Nimbus DD2.3.
What I got wrong is that on older CPUs, where firmware has disabled
the count cache, we also need to flush the link stack on context
switch.
To fix it we create a new feature bit which is not set by firmware,
which tells us we need to flush the link stack. We set that when
firmware tells us that either of the existing Spectre v2 mitigations
are enabled.
Then we adjust the patching code so that if we see that feature bit we
enable the link stack flush. If we're also told to flush the count
cache in software then we fall through and do that also.
On the older CPUs we don't need to do do the software count cache
flush, firmware has disabled it, so in that case we patch in an early
return after the link stack flush.
The naming of some of the functions is awkward after this patch,
because they're called "count cache" but they also do link stack. But
we'll fix that up in a later commit to ease backporting.
This is the fix for CVE-2019-18660.
Reported-by: Anthony Steinhauser <asteinhauser@google.com> Fixes: ee13cb249fab ("powerpc/64s: Add support for software count cache flush") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for disabling the kernel implemented spectre v2 mitigation
(count cache flush on context switch) via the nospectre_v2 and
mitigations=off cmdline options.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Christopher M. Riedl <cmr@informatik.wtf> Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190524024647.381-1-cmr@informatik.wtf Signed-off-by: Daniel Axtens <dja@axtens.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The userspace comedilib function 'get_cmd_generic_timed' fills
the cmd structure with an informed guess and then calls the
function 'usbduxfast_ai_cmdtest' in this driver repeatedly while
'usbduxfast_ai_cmdtest' is modifying the cmd struct until it
no longer changes. However, because of rounding errors this never
converged because 'steps = (cmd->convert_arg * 30) / 1000' and then
back to 'cmd->convert_arg = (steps * 1000) / 30' won't be the same
because of rounding errors. 'Steps' should only be converted back to
the 'convert_arg' if 'steps' has actually been modified. In addition
the case of steps being 0 wasn't checked which is also now done.
These are the Foxconn-branded variants of the Dell DW5821e modules,
same USB layout as those. The device exposes AT, NMEA and DIAG ports
in both USB configurations.
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
The driver was setting the device remote-wakeup feature during probe in
violation of the USB specification (which says it should only be set
just prior to suspending the device). This could potentially waste
power during suspend as well as lead to spurious wakeups.
Note that USB core would clear the remote-wakeup feature at first
resume.
Fixes: 0f64478cbc7a ("USB: add USB serial mos7720 driver") Cc: stable <stable@vger.kernel.org> # 2.6.19 Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add USB ID for MOXA UPort 2210. This device contains mos7820 but
it passes GPIO0 check implemented by driver and it's detected as
mos7840. Hence product id check is added to force mos7820 mode.
Signed-off-by: Pavel Löbl <pavel@loebl.cz> Cc: stable <stable@vger.kernel.org>
[ johan: rename id defines and add vendor-id check ] Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. stale memory left over from the last transfer
the actual length of the data transfered needs to be checked
2. memory already freed
the error handling in appledisplay_probe() needs
to cancel the work in that case
In case of a timeout or if a signal aborts a read
communication with the device needs to be ended
lest we overwrite an active URB the next time we
do IO to the device, as the URB may still be active.
Smatch reported that nents is not initialized and used in
stub_recv_cmd_submit(). nents is currently initialized by sgl_alloc()
and used to allocate multiple URBs when host controller doesn't
support scatter-gather DMA. The use of uninitialized nents means that
buf_len is zero and use_sg is true. But buffer length should not be
zero when an URB uses scatter-gather DMA.
To prevent this situation, add the conditional that checks buf_len
and use_sg. And move the use of nents right after the sgl_alloc() to
avoid the use of uninitialized nents.
If the error occurs, it adds SDEV_EVENT_ERROR_MALLOC and stub_priv
will be released by stub event handler and connection will be shut
down.
Fixes: ea44d190764b ("usbip: Implement SG support to vhci-hcd and stub driver") Reported-by: kbuild test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Suwan Kim <suwan.kim027@gmail.com> Acked-by: Shuah Khan <skhan@linuxfoundation.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191111141035.27788-1-suwan.kim027@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
slab_alloc_node() already zeroed out the freelist pointer if
init_on_free was on. Thibaut Sautereau noticed that the same needs to
be done for kmem_cache_alloc_bulk(), which performs the allocations
separately.
kmem_cache_alloc_bulk() is currently used in two places in the kernel,
so this change is unlikely to have a major performance impact.
SLAB doesn't require a similar change, as auto-initialization makes the
allocator store the freelist pointers off-slab.
Link: http://lkml.kernel.org/r/20191007091605.30530-1-glider@google.com Fixes: 6471384af2a6 ("mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options") Signed-off-by: Alexander Potapenko <glider@google.com> Reported-by: Thibaut Sautereau <thibaut@sautereau.fr> Reported-by: Kees Cook <keescook@chromium.org> Cc: Christoph Lameter <cl@linux.com> Cc: Laura Abbott <labbott@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix multiple cases of out of bounds (OOB) read associated with
MCE device receive/input data handling.
In reference for the OOB cases below, the incoming/read (byte) data
format when the MCE device responds to a command is:
{ cmd_prefix, subcmd, data0, data1, ... }
where cmd_prefix are:
MCE_CMD_PORT_SYS
MCE_CMD_PORT_IR
and subcmd examples are:
MCE_RSP_GETPORTSTATUS
MCE_RSP_EQIRNUMPORTS
...
Response size dynamically depends on cmd_prefix and subcmd.
So data0, data1, ... may or may not be present on input.
Multiple responses may return in a single receiver buffer.
The trigger condition for OOB read is typically random or
corrupt input data that fills the mceusb receiver buffer.
Case 1:
mceusb_handle_command() reads data0 (var hi) and data1 (var lo)
regardless of whether the response includes such data.
If { cmd_prefix, subcmd } is at the end of the receiver buffer,
read past end of buffer occurs.
This case was reported by
KASAN: slab-out-of-bounds Read in mceusb_dev_recv
https://syzkaller.appspot.com/bug?extid=c7fdb6cb36e65f2fe8c9
Fix: In mceusb_handle_command(), change variable hi and lo to
pointers, and dereference only when required.
Case 2:
If response with data is truncated at end of buffer after
{ cmd_prefix, subcmd }, mceusb_handle_command() reads past
end of buffer for data0, data1, ...
Fix: In mceusb_process_ir_data(), check response size with
remaining buffer size before invoking mceusb_handle_command().
+ if (i + ir->rem < buf_len)
mceusb_handle_command(ir, &ir->buf_in[i - 1]);
Case 3:
mceusb_handle_command() handles invalid/bad response such as
{ 0x??, MCE_RSP_GETPORTSTATUS } of length 2 as a response
{ MCE_CMD_PORT_SYS, MCE_RSP_GETPORTSTATUS, data0, ... }
of length 7. Read OOB occurs for non-existent data0, data1, ...
Cause is mceusb_handle_command() does not check cmd_prefix value.
Fix: mceusb_handle_command() must test both cmd_prefix and subcmd.
Case 4:
mceusb_process_ir_data() receiver parser state SUBCMD is
possible at start (i=0) of receiver buffer resulting in buffer
offset=-1 passed to mceusb_dev_printdata().
Bad offset results in OOB read before start of buffer.
[1214218.580308] mceusb 1-1.3:1.0: rx data[0]: 00 80 (length=2)
[1214218.580323] mceusb 1-1.3:1.0: Unknown command 0x00 0x80
...
[1214218.580406] mceusb 1-1.3:1.0: rx data[14]: 7f 7f (length=2)
[1214218.679311] mceusb 1-1.3:1.0: rx data[-1]: 80 90 (length=2)
[1214218.679325] mceusb 1-1.3:1.0: End of raw IR data
[1214218.679340] mceusb 1-1.3:1.0: rx data[1]: 7f 7f (length=2)
Fix: If parser_state is SUBCMD after processing receiver buffer,
reset parser_state to CMD_HEADER.
In effect, discard cmd_prefix at end of receiver buffer.
In mceusb_dev_printdata(), abort if buffer offset is out of bounds.
Case 5:
If response with data is truncated at end of buffer after
{ cmd_prefix, subcmd }, mceusb_dev_printdata() reads past
end of buffer for data0, data1, ...
while decoding the response to print out.
Fix: In mceusb_dev_printdata(), remove unneeded buffer offset
adjustments (var start and var skip) associated with MCE gen1 header.
Test for truncated MCE cmd response (compare offset+len with buf_len)
and skip decoding of incomplete response.
Move IR data tracing to execute before the truncation test.
Signed-off-by: A Sun <as1033x@comcast.net> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The touch timer is set up in intf1. If the second interface does not exist,
the timer and touch input device are not setup and we get the following
error, when touch events are reported via intf0.
Local variable description: ----ircode@cxusb_rc_query
Variable was created at:
cxusb_rc_query+0x4d/0x360 drivers/media/usb/dvb-usb/cxusb.c:543
dvb_usb_read_remote_control+0xf9/0x290 drivers/media/usb/dvb-usb/dvb-usb-remote.c:261
Signed-off-by: Vito Caputo <vcaputo@pengaru.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When parsing the UVC control descriptors fails, the error path tries to
cleanup a media device that hasn't been initialised, potentially
resulting in a crash. Fix this by initialising the media device before
the error handling path can be reached.
Visual inspection of the usbvision driver shows that it suffers from
three races between its open, close, and disconnect handlers. In
particular, the driver is careful to update its usbvision->user and
usbvision->remove_pending flags while holding the private mutex, but:
usbvision_v4l2_close() and usbvision_radio_close() don't hold
the mutex while they check the value of
usbvision->remove_pending;
usbvision_disconnect() doesn't hold the mutex while checking
the value of usbvision->user; and
also, usbvision_v4l2_open() and usbvision_radio_open() don't
check whether the device has been unplugged before allowing
the user to open the device files.
Each of these can potentially lead to usbvision_release() being called
twice and use-after-free errors.
This patch fixes the races by reading the flags while the mutex is
still held and checking for pending removes before allowing an open to
succeed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: <stable@vger.kernel.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer found two invalid-access bugs in the usbvision
driver. These bugs occur when userspace keeps the device file open
after the device has been disconnected and usbvision_disconnect() has
set usbvision->dev to NULL:
When the device file is closed, usbvision_radio_close() tries
to issue a usb_set_interface() call, passing the NULL pointer
as its first argument.
If userspace performs a querycap ioctl call, vidioc_querycap()
calls usb_make_path() with the same NULL pointer.
This patch fixes the problems by making the appropriate tests
beforehand. Note that vidioc_querycap() is protected by
usbvision->v4l2_lock, acquired in a higher layer of the V4L2
subsystem.
There is the same incorrect approach to locking implemented in
vivid_stop_generating_vid_cap(), vivid_stop_generating_vid_out() and
sdr_cap_stop_streaming().
These functions are called during streaming stopping with vivid_dev.mutex
locked. And they all do the same mistake while stopping their kthreads,
which need to lock this mutex as well. See the example from
vivid_stop_generating_vid_cap():
/* shutdown control thread */
vivid_grab_controls(dev, false);
mutex_unlock(&dev->mutex);
kthread_stop(dev->kthread_vid_cap);
dev->kthread_vid_cap = NULL;
mutex_lock(&dev->mutex);
But when this mutex is unlocked, another vb2_fop_read() can lock it
instead of vivid_thread_vid_cap() and manipulate the buffer queue.
That causes a use-after-free access later.
To fix those issues let's:
1. avoid unlocking the mutex in vivid_stop_generating_vid_cap(),
vivid_stop_generating_vid_out() and sdr_cap_stop_streaming();
2. use mutex_trylock() with schedule_timeout_uninterruptible() in
the loops of the vivid kthread handlers.
Signed-off-by: Alexander Popov <alex.popov@linux.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v3.18 and up Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>