When the client attempts to tree connect to a domain-based DFS
namespace from a DFS interlink target, the server will return
STATUS_BAD_NETWORK_NAME and the following will appear on dmesg:
CIFS: VFS: BAD_NETWORK_NAME: \\dom\dfs
Since a DFS share might contain several DFS interlinks and they expire
after 10 minutes, the above message might end up being flooded on
dmesg when mounting or accessing them.
Print this only once per share.
Signed-off-by: Paulo Alcantara (Red Hat) <pc@manguebit.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A null dereference or oops exception will eventually occur when qla1280.c
driver is compiled with DEBUG_QLA1280 enabled and ql_debug_level > 2. I
think its clear from the code that the intention here is sg_dma_len(s) not
length of sg_next(s) when printing the debug info.
There is currently no mechanism to return error from query responses.
Return the error and print the corresponding error message with it.
Signed-off-by: Seunghui Lee <sh043.lee@samsung.com> Link: https://lore.kernel.org/r/20250118023808.24726-1-sh043.lee@samsung.com Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Filesystems can write to disk from page reclaim with __GFP_FS
set. Marc found a case where scsi_realloc_sdev_budget_map() ends up in
page reclaim with GFP_KERNEL, where it could try to take filesystem
locks again, leading to a deadlock.
WARNING: possible circular locking dependency detected
6.13.0 #1 Not tainted
------------------------------------------------------
kswapd0/70 is trying to acquire lock: ffff8881025d5d78 (&q->q_usage_counter(io)){++++}-{0:0}, at: blk_mq_submit_bio+0x461/0x6e0
but task is already holding lock: ffffffff81ef5f40 (fs_reclaim){+.+.}-{0:0}, at: balance_pgdat+0x9f/0x760
The full lockdep splat can be found in Marc's report:
https://lkml.org/lkml/2025/1/24/1101
Avoid the potential deadlock by doing the allocation with GFP_NOIO, which
prevents both filesystem and block layer recursion.
Reported-by: Marc Aurèle La France <tsi@tuyoix.net> Signed-off-by: Rik van Riel <riel@surriel.com> Link: https://lore.kernel.org/r/20250129104525.0ae8421e@fangorn Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[WHAT & HOW]
hpo_stream_to_link_encoder_mapping has size MAX_HPO_DP2_ENCODERS(=4),
but location can have size up to 6. As a result, it is necessary to
check location against MAX_HPO_DP2_ENCODERS.
Similiarly, disp_cfg_stream_location can be used as an array index which
should be 0..5, so the ASSERT's conditions should be less without equal.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3904 Reviewed-by: Austin Zheng <Austin.Zheng@amd.com> Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pmc_core_ltr_show(), promote 'val' to 'u64' to avoid possible integer
overflow. Values (10 bit) are multiplied by the scale, the result of
expression is in a range from 1 to 34,326,183,936 which is bigger then
UINT32_MAX. Compile tested only.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
857b158dc5e8 ("sched/eevdf: Use sched_attr::sched_runtime to set request/slice suggestion")
... we have the userspace per-task tunable slice length, which is
a key parameter that is otherwise difficult to obtain, so provide
it in /proc/$PID/sched.
When performing an iSCSI boot using IPv6, iscsistart still reads the
/sys/firmware/ibft/ethernetX/subnet-mask entry. Since the IPv6 prefix
length is 64, this causes the shift exponent to become negative,
triggering a UBSAN warning. As the concept of a subnet mask does not
apply to IPv6, the value is set to ~0 to suppress the warning message.
Signed-off-by: Chengen Du <chengen.du@canonical.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
futex_queue() -> __futex_queue() uses 'current' as the task to store in
the struct futex_q->task field. This is fine for synchronous usage of
the futex infrastructure, but it's not always correct when used by
io_uring where the task doing the initial futex_queue() might not be
available later on. This doesn't lead to any issues currently, as the
io_uring side doesn't support PI futexes, but it does leave a
potentially dangling pointer which is never a good idea.
Have futex_queue() take a task_struct argument, and have the regular
callers pass in 'current' for that. Meanwhile io_uring can just pass in
NULL, as the task should never be used off that path. In theory
req->tctx->task could be used here, but there's no point populating it
with a task field that will never be used anyway.
At btrfs_qgroup_cleanup_dropped_subvolume() all we want to commit the
current transaction in order to have all the qgroup rfer/excl numbers up
to date. However we are using btrfs_start_transaction(), which joins the
current transaction if there is one that is not yet committing, but also
starts a new one if there is none or if the current one is already
committing (its state is >= TRANS_STATE_COMMIT_START). This later case
results in unnecessary IO, wasting time and a pointless rotation of the
backup roots in the super block.
So instead of using btrfs_start_transaction() followed by a
btrfs_commit_transaction(), use btrfs_commit_current_transaction() which
achieves our purpose and avoids starting and committing new transactions.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a connectivity loss occurs while nvme_fc_create_assocation is
being executed, it's possible that the ctrl ends up stuck in the LIVE
state:
1) nvme nvme10: NVME-FC{10}: create association : ...
2) nvme nvme10: NVME-FC{10}: controller connectivity lost.
Awaiting Reconnect
nvme nvme10: queue_size 128 > ctrl maxcmd 32, reducing to maxcmd
3) nvme nvme10: Could not set queue count (880)
nvme nvme10: Failed to configure AEN (cfg 900)
4) nvme nvme10: NVME-FC{10}: controller connect complete
5) nvme nvme10: failed nvme_keep_alive_end_io error=4
A connection attempt starts 1) and the ctrl is in state CONNECTING.
Shortly after the LLDD driver detects a connection lost event and calls
nvme_fc_ctrl_connectivity_loss 2). Because we are still in CONNECTING
state, this event is ignored.
nvme_fc_create_association continues to run in parallel and tries to
communicate with the controller and these commands will fail. Though
these errors are filtered out, e.g in 3) setting the I/O queues numbers
fails which leads to an early exit in nvme_fc_create_io_queues. Because
the number of IO queues is 0 at this point, there is nothing left in
nvme_fc_create_association which could detected the connection drop.
Thus the ctrl enters LIVE state 4).
Eventually the keep alive handler times out 5) but because nothing is
being done, the ctrl stays in LIVE state.
There is already the ASSOC_FAILED flag to track connectivity loss event
but this bit is set too late in the recovery code path. Move this into
the connectivity loss event handler and synchronize it with the state
change. This ensures that the ASSOC_FAILED flag is seen by
nvme_fc_create_io_queues and it does not enter the LIVE state after a
connectivity loss event. If the connectivity loss event happens after we
entered the LIVE state the normal error recovery path is executed.
Signed-off-by: Daniel Wagner <wagi@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The initial controller initialization mimiks the reconnect loop
behavior by switching from NEW to RESETTING and then to CONNECTING.
The transition from NEW to CONNECTING is a valid transition, so there is
no point entering the RESETTING state. TCP and RDMA also transition
directly to CONNECTING state.
Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Daniel Wagner <wagi@kernel.org> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
mlx5_eswitch_get_vepa returns -EPERM if the device lacks
eswitch_manager capability, blocking mlx5e_bridge_getlink from
retrieving VEPA mode. Since mlx5e_bridge_getlink implements
ndo_bridge_getlink, returning -EPERM causes bridge link show to fail
instead of skipping devices without this capability.
To avoid this, return -EOPNOTSUPP from mlx5e_bridge_getlink when
mlx5_eswitch_get_vepa fails, ensuring the command continues processing
other devices while ignoring those without the necessary capability.
Fixes: 4b89251de024 ("net/mlx5: Support ndo bridge_setlink and getlink") Signed-off-by: Carolina Jubran <cjubran@nvidia.com> Reviewed-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Link: https://patch.msgid.link/1741644104-97767-7-git-send-email-tariqt@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing LAG device from bridge, NETDEV_CHANGEUPPER event is
triggered. Driver finds the lower devices (PFs) to flush all the
offloaded entries. And mlx5_lag_is_shared_fdb is checked, it returns
false if one of PF is unloaded. In such case,
mlx5_esw_bridge_lag_rep_get() and its caller return NULL, instead of
the alive PF, and the flush is skipped.
Besides, the bridge fdb entry's lastuse is updated in mlx5 bridge
event handler. But this SWITCHDEV_FDB_ADD_TO_BRIDGE event can be
ignored in this case because the upper interface for bond is deleted,
and the entry will never be aged because lastuse is never updated.
To make things worse, as the entry is alive, mlx5 bridge workqueue
keeps sending that event, which is then handled by kernel bridge
notifier. It causes the following crash when accessing the passed bond
netdev which is already destroyed.
To fix this issue, remove such checks. LAG state is already checked in
commit 15f8f168952f ("net/mlx5: Bridge, verify LAG state when adding
bond to bridge"), driver still need to skip offload if LAG becomes
invalid state after initialization.
mlx5_irq_pool_get() is a getter for completion IRQ pool only.
However, after the cited commit, mlx5_irq_pool_get() is called during
ctrl IRQ release flow to retrieve the pool, resulting in the use of an
incorrect IRQ pool.
Hence, use the newly introduced mlx5_irq_get_pool() getter to retrieve
the correct IRQ pool based on the IRQ itself. While at it, rename
mlx5_irq_pool_get() to mlx5_irq_table_get_comp_irq_pool() which
accurately reflects its purpose and improves code readability.
The bwc layer was clamping the matcher priority from 32 bits to 16 bits.
This didn't show up until a matcher was resized, since the initial
native matcher was created using the correct 32 bit value.
The fix also reorders fields to avoid some padding.
Currently, ovs_ct_set_labels() is only called for confirmed conntrack
entries (ct) within ovs_ct_commit(). However, if the conntrack entry
does not have the labels_ext extension, attempting to allocate it in
ovs_ct_get_conn_labels() for a confirmed entry triggers a warning in
nf_ct_ext_add():
WARN_ON(nf_ct_is_confirmed(ct));
This happens when the conntrack entry is created externally before OVS
increments net->ct.labels_used. The issue has become more likely since
commit fcb1aa5163b1 ("openvswitch: switch to per-action label counting
in conntrack"), which changed to use per-action label counting and
increment net->ct.labels_used when a flow with ct action is added.
Since there’s no straightforward way to fully resolve this issue at the
moment, this reverts the commit to avoid breaking existing use cases.
Fixes: fcb1aa5163b1 ("openvswitch: switch to per-action label counting in conntrack") Reported-by: Jianbo Liu <jianbol@nvidia.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Aaron Conole <aconole@redhat.com> Link: https://patch.msgid.link/1bdeb2f3a812bca016a225d3de714427b2cd4772.1741457143.git.lucien.xin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The actions length check is unreliable and produces different results
depending on the initial length of the provided netlink attribute and
the composition of the actual actions inside of it. For example, a
user can add 4088 empty clone() actions without triggering -EMSGSIZE,
on attempt to add 4089 such actions the operation will fail with the
-EMSGSIZE verdict. However, if another 16 KB of other actions will
be *appended* to the previous 4089 clone() actions, the check passes
and the flow is successfully installed into the openvswitch datapath.
The reason for a such a weird behavior is the way memory is allocated.
When ovs_flow_cmd_new() is invoked, it calls ovs_nla_copy_actions(),
that in turn calls nla_alloc_flow_actions() with either the actual
length of the user-provided actions or the MAX_ACTIONS_BUFSIZE. The
function adds the size of the sw_flow_actions structure and then the
actually allocated memory is rounded up to the closest power of two.
So, if the user-provided actions are larger than MAX_ACTIONS_BUFSIZE,
then MAX_ACTIONS_BUFSIZE + sizeof(*sfa) rounded up is 32K + 24 -> 64K.
Later, while copying individual actions, we look at ksize(), which is
64K, so this way the MAX_ACTIONS_BUFSIZE check is not actually
triggered and the user can easily allocate almost 64 KB of actions.
However, when the initial size is less than MAX_ACTIONS_BUFSIZE, but
the actions contain ones that require size increase while copying
(such as clone() or sample()), then the limit check will be performed
during the reserve_sfa_size() and the user will not be allowed to
create actions that yield more than 32 KB internally.
This is one part of the problem. The other part is that it's not
actually possible for the userspace application to know beforehand
if the particular set of actions will be rejected or not.
Certain actions require more space in the internal representation,
e.g. an empty clone() takes 4 bytes in the action list passed in by
the user, but it takes 12 bytes in the internal representation due
to an extra nested attribute, and some actions require less space in
the internal representations, e.g. set(tunnel(..)) normally takes
64+ bytes in the action list provided by the user, but only needs to
store a single pointer in the internal implementation, since all the
data is stored in the tunnel_info structure instead.
And the action size limit is applied to the internal representation,
not to the action list passed by the user. So, it's not possible for
the userpsace application to predict if the certain combination of
actions will be rejected or not, because it is not possible for it to
calculate how much space these actions will take in the internal
representation without knowing kernel internals.
All that is causing random failures in ovs-vswitchd in userspace and
inability to handle certain traffic patterns as a result. For example,
it is reported that adding a bit more than a 1100 VMs in an OpenStack
setup breaks the network due to OVS not being able to handle ARP
traffic anymore in some cases (it tries to install a proper datapath
flow, but the kernel rejects it with -EMSGSIZE, even though the action
list isn't actually that large.)
Kernel behavior must be consistent and predictable in order for the
userspace application to use it in a reasonable way. ovs-vswitchd has
a mechanism to re-direct parts of the traffic and partially handle it
in userspace if the required action list is oversized, but that doesn't
work properly if we can't actually tell if the action list is oversized
or not.
Solution for this is to check the size of the user-provided actions
instead of the internal representation. This commit just removes the
check from the internal part because there is already an implicit size
check imposed by the netlink protocol. The attribute can't be larger
than 64 KB. Realistically, we could reduce the limit to 32 KB, but
we'll be risking to break some existing setups that rely on the fact
that it's possible to create nearly 64 KB action lists today.
Vast majority of flows in real setups are below 100-ish bytes. So
removal of the limit will not change real memory consumption on the
system. The absolutely worst case scenario is if someone adds a flow
with 64 KB of empty clone() actions. That will yield a 192 KB in the
internal representation consuming 256 KB block of memory. However,
that list of actions is not meaningful and also a no-op. Real world
very large action lists (that can occur for a rare cases of BUM
traffic handling) are unlikely to contain a large number of clones and
will likely have a lot of tunnel attributes making the internal
representation comparable in size to the original action list.
So, it should be fine to just remove the limit.
Commit in the 'Fixes' tag is the first one that introduced the
difference between internal representation and the user-provided action
lists, but there were many more afterwards that lead to the situation
we have today.
Use addrconf_addr_gen() to generate IPv6 link-local addresses on GRE
devices in most cases and fall back to using add_v4_addrs() only in
case the GRE configuration is incompatible with addrconf_addr_gen().
GRE used to use addrconf_addr_gen() until commit e5dd729460ca
("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL
address") restricted this use to gretap and ip6gretap devices, and
created add_v4_addrs() (borrowed from SIT) for non-Ethernet GRE ones.
The original problem came when commit 9af28511be10 ("addrconf: refuse
isatap eui64 for INADDR_ANY") made __ipv6_isatap_ifid() fail when its
addr parameter was 0. The commit says that this would create an invalid
address, however, I couldn't find any RFC saying that the generated
interface identifier would be wrong. Anyway, since gre over IPv4
devices pass their local tunnel address to __ipv6_isatap_ifid(), that
commit broke their IPv6 link-local address generation when the local
address was unspecified.
Then commit e5dd729460ca ("ip/ip6_gre: use the same logic as SIT
interfaces when computing v6LL address") tried to fix that case by
defining add_v4_addrs() and calling it to generate the IPv6 link-local
address instead of using addrconf_addr_gen() (apart for gretap and
ip6gretap devices, which would still use the regular
addrconf_addr_gen(), since they have a MAC address).
That broke several use cases because add_v4_addrs() isn't properly
integrated into the rest of IPv6 Neighbor Discovery code. Several of
these shortcomings have been fixed over time, but add_v4_addrs()
remains broken on several aspects. In particular, it doesn't send any
Router Sollicitations, so the SLAAC process doesn't start until the
interface receives a Router Advertisement. Also, add_v4_addrs() mostly
ignores the address generation mode of the interface
(/proc/sys/net/ipv6/conf/*/addr_gen_mode), thus breaking the
IN6_ADDR_GEN_MODE_RANDOM and IN6_ADDR_GEN_MODE_STABLE_PRIVACY cases.
Fix the situation by using add_v4_addrs() only in the specific scenario
where the normal method would fail. That is, for interfaces that have
all of the following characteristics:
* run over IPv4,
* transport IP packets directly, not Ethernet (that is, not gretap
interfaces),
* tunnel endpoint is INADDR_ANY (that is, 0),
* device address generation mode is EUI64.
In all other cases, revert back to the regular addrconf_addr_gen().
Also, remove the special case for ip6gre interfaces in add_v4_addrs(),
since ip6gre devices now always use addrconf_addr_gen() instead.
Fixes: e5dd729460ca ("ip/ip6_gre: use the same logic as SIT interfaces when computing v6LL address") Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/559c32ce5c9976b269e6337ac9abb6a96abe5096.1741375285.git.gnault@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an incorrect calculation in the offset variable which causes
the nft_skb_copy_to_reg() function to always return -EFAULT. Adding the
start variable is redundant. In the __ip_options_compile() function the
correct offset is specified when finding the function. There is no need
to add the size of the iphdr structure to the offset.
Fixes: dbb5281a1f84 ("netfilter: nf_tables: add support for matching IPv4 options") Signed-off-by: Alexey Kashavkin <akashavkin@gmail.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function qdisc_tree_reduce_backlog() uses TC_H_ROOT as a termination
condition when traversing up the qdisc tree to update parent backlog
counters. However, if a class is created with classid TC_H_ROOT, the
traversal terminates prematurely at this class instead of reaching the
actual root qdisc, causing parent statistics to be incorrectly maintained.
In case of DRR, this could lead to a crash as reported by Mingi Cho.
Prevent the creation of any Qdisc class with classid TC_H_ROOT
(0xFFFFFFFF) across all qdisc types, as suggested by Jamal.
Reported-by: Mingi Cho <mincho@theori.io> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Fixes: 066a3b5b2346 ("[NET_SCHED] sch_api: fix qdisc_tree_decrease_qlen() loop") Link: https://patch.msgid.link/20250306232355.93864-2-xiyou.wangcong@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The get->num_services variable is an unsigned int which is controlled by
the user. The struct_size() function ensures that the size calculation
does not overflow an unsigned long, however, we are saving the result to
an int so the calculation can overflow.
Both "len" and "get->num_services" come from the user. This check is
just a sanity check to help the user and ensure they are using the API
correctly. An integer overflow here is not a big deal. This has no
security impact.
Save the result from struct_size() type size_t to fix this integer
overflow bug.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit b36e4523d4d5 ("netfilter: nf_conncount: fix garbage
collection confirm race"), `cpu` and `jiffies32` were introduced to
the struct nf_conncount_tuple.
The commit made nf_conncount_add() initialize `conn->cpu` and
`conn->jiffies32` when allocating the struct.
In contrast, count_tree() was not changed to initialize them.
By commit 34848d5c896e ("netfilter: nf_conncount: Split insert and
traversal"), count_tree() was split and the relevant allocation
code now resides in insert_tree().
Initialize `conn->cpu` and `conn->jiffies32` in insert_tree().
Since rtase_init_ring, which is called within rtase_sw_reset, adds ring
entries already present in the ring list back into the list, it causes
the ring list to form a cycle. This results in list_for_each_entry_safe
failing to find an endpoint during traversal, leading to an error.
Therefore, it is necessary to remove the previously added ring_list nodes
before calling rtase_init_ring.
Fixes: 079600489960 ("rtase: Implement net_device_ops") Signed-off-by: Justin Lai <justinlai0215@realtek.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250306070510.18129-1-justinlai0215@realtek.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When validation on the backup slave is enabled, we need to validate the
Neighbor Solicitation (NS) messages received on the backup slave. To
receive these messages, the correct destination MAC address must be added
to the slave. However, the target in bonding is a unicast address, which
we cannot use directly. Instead, we should first convert it to a
Solicited-Node Multicast Address and then derive the corresponding MAC
address.
Fix the incorrect MAC address setting on both slave_set_ns_maddr() and
slave_set_ns_maddrs(). Since the two function names are similar. Add
some description for the functions. Also only use one mac_addr variable
in slave_set_ns_maddr() to save some code and logic.
Fixes: 8eb36164d1a6 ("bonding: add ns target multicast address to slave device") Acked-by: Jay Vosburgh <jv@jvosburgh.net> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250306023923.38777-2-liuhangbin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that the frag_list used for reassembly isn't shared with other
packets. This avoids incorrect reassembly when packets are cloned, and
prevents a memory leak due to circular references between fragments and
their skb_shared_info.
The upcoming MCTP-over-USB driver uses skb_clone which can trigger the
problem - other MCTP drivers don't share SKBs.
A kunit test is added to reproduce the issue.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au> Fixes: 4a992bbd3650 ("mctp: Implement message fragmentation & reassembly") Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250306-matt-mctp-usb-v1-1-085502b3dd28@codeconstruct.com.au Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A blocking notification chain uses a read-write semaphore to protect the
integrity of the chain. The semaphore is acquired for writing when
adding / removing notifiers to / from the chain and acquired for reading
when traversing the chain and informing notifiers about an event.
In case of the blocking switchdev notification chain, recursive
notifications are possible which leads to the semaphore being acquired
twice for reading and to lockdep warnings being generated [1].
Specifically, this can happen when the bridge driver processes a
SWITCHDEV_BRPORT_UNOFFLOADED event which causes it to emit notifications
about deferred events when calling switchdev_deferred_process().
Fix this by converting the notification chain to a raw notification
chain in a similar fashion to the netdev notification chain. Protect
the chain using the RTNL mutex by acquiring it when modifying the chain.
Events are always informed under the RTNL mutex, but add an assertion in
call_switchdev_blocking_notifiers() to make sure this is not violated in
the future.
Maintain the "blocking" prefix as events are always emitted from process
context and listeners are allowed to block.
[1]:
WARNING: possible recursive locking detected 6.14.0-rc4-custom-g079270089484 #1 Not tainted
--------------------------------------------
ip/52731 is trying to acquire lock: ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
but task is already holding lock: ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((switchdev_blocking_notif_chain).rwsem);
lock((switchdev_blocking_notif_chain).rwsem);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by ip/52731:
#0: ffffffff84f795b0 (rtnl_mutex){+.+.}-{4:4}, at: rtnl_newlink+0x727/0x1dc0
#1: ffffffff8731f628 (&net->rtnl_mutex){+.+.}-{4:4}, at: rtnl_newlink+0x790/0x1dc0
#2: ffffffff850918d8 ((switchdev_blocking_notif_chain).rwsem){++++}-{4:4}, at: blocking_notifier_call_chain+0x58/0xa0
When the queue is reset, the bnxt_alloc_one_tpa_info() is called to
allocate tpa_info for the new queue.
And then the old queue's tpa_info should be removed by the
bnxt_free_one_tpa_info(), but it is not called.
So memory leak occurs.
It adds the bnxt_free_one_tpa_info() in the bnxt_queue_mem_free().
Commit 7ed816be35ab ("eth: bnxt: use page pool for head frags") added a
page pool for header frags, which may be distinct from the existing pool
for the aggregation ring. Prior to this change, frags used in the TPA
ring rx_tpa were allocated from system memory e.g. napi_alloc_frag()
meaning their lifetimes were not associated with a page pool. They can
be returned at any time and so the queue API did not alloc or free
rx_tpa.
But now frags come from a separate head_pool which may be different to
page_pool. Without allocating and freeing rx_tpa, frags allocated from
the old head_pool may be returned to a different new head_pool which
causes a mismatch between the pp hold/release count.
Fix this problem by properly freeing and allocating rx_tpa in the queue
API implementation.
Signed-off-by: David Wei <dw@davidwei.uk> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20241204041022.56512-4-dw@davidwei.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 87dd2850835d ("eth: bnxt: fix memory leak in queue reset") Signed-off-by: Sasha Levin <sashal@kernel.org>
Testing small size RPCs (300B-400B) on a large AMD system suggests
that page pool recycling is very useful even for just the head frags.
With this patch (and copy break disabled) I see a 30% performance
improvement (82Gbps -> 106Gbps).
Convert bnxt from normal page frags to page pool frags for head buffers.
On systems with small page size we can use the same pool as for TPA
pages. On systems with large pages the frag allocation logic of the
page pool is already used to split a large page into TPA chunks.
TPA chunks are much larger than heads (8k or 64k, AFAICT vs 1kB)
and we always allocate the same sized chunks. Mixing allocation
of TPA and head pages would lead to sub-optimal memory use.
Plus Taehee's work on zero-copy / devmem will need to differentiate
between TPA and non-TPA page pool, anyway. Conditionally allocate
a new page pool for heads.
When qstats-get operation is executed, callbacks of netdev_stats_ops
are called. The bnxt_get_queue_stats{rx | tx} collect per-queue stats
from sw_stats in the rings.
But {rx | tx | cp}_ring are allocated when the interface is up.
So, these rings are not allocated when the interface is down.
The qstats-get is allowed even if the interface is down. However,
the bnxt_get_queue_stats{rx | tx}() accesses cp_ring and tx_ring
without null check.
So, it needs to avoid accessing rings if the interface is down.
Reproducer:
ip link set $interface down
./cli.py --spec netdev.yaml --dump qstats-get
OR
ip link set $interface down
python ./stats.py
The bnxt_rx_pkt() updates ip_summed value at the end if checksum offload
is enabled.
When the XDP-MB program is attached and it returns XDP_PASS, the
bnxt_xdp_build_skb() is called to update skb_shared_info.
The main purpose of bnxt_xdp_build_skb() is to update skb_shared_info,
but it updates ip_summed value too if checksum offload is enabled.
This is actually duplicate work.
When the bnxt_rx_pkt() updates ip_summed value, it checks if ip_summed
is CHECKSUM_NONE or not.
It means that ip_summed should be CHECKSUM_NONE at this moment.
But ip_summed may already be updated to CHECKSUM_UNNECESSARY in the
XDP-MB-PASS path.
So the by skb_checksum_none_assert() WARNS about it.
This is duplicate work and updating ip_summed in the
bnxt_xdp_build_skb() is not needed.
When a queue is restarted, it sets MRU to 0 for stopping packet flow.
MRU variable is a member of vnic_info[], the first vnic_info is default
and the second is ntuple.
Only when ntuple is enabled(ethtool -K eth0 ntuple on), vnic_info for
ntuple is allocated in init logic.
The bp->nr_vnics indicates how many vnic_info are allocated.
However bnxt_queue_{start | stop}() accesses vnic_info[BNXT_VNIC_NTUPLE]
regardless of ntuple state.
The bnxt_queue_mem_alloc() is called to allocate new queue memory when
a queue is restarted.
It internally accesses rx buffer descriptor corresponding to the index.
The rx buffer descriptor is allocated and set when the interface is up
and it's freed when the interface is down.
So, if queue is restarted if interface is down, kernel panic occurs.
When mb-xdp is set and return is XDP_PASS, packet is converted from
xdp_buff to sk_buff with xdp_update_skb_shared_info() in
bnxt_xdp_build_skb().
bnxt_xdp_build_skb() passes incorrect truesize argument to
xdp_update_skb_shared_info().
The truesize is calculated as BNXT_RX_PAGE_SIZE * sinfo->nr_frags but
the skb_shared_info was wiped by napi_build_skb() before.
So it stores sinfo->nr_frags before bnxt_xdp_build_skb() and use it
instead of getting skb_shared_info from xdp_get_shared_info_from_buff().
How to reproduce:
<Node A>
ip link set $interface1 xdp obj xdp_pass.o
ip link set $interface1 mtu 9000 up
ip a a 10.0.0.1/24 dev $interface1
<Node B>
ip link set $interfac2 mtu 9000 up
ip a a 10.0.0.2/24 dev $interface2
ping 10.0.0.1 -s 65000
Following ping.py patch adds xdp-mb-pass case. so ping.py is going to be
able to reproduce this issue.
Fixes: 1dc4c557bfed ("bnxt: adding bnxt_xdp_build_skb to build skb from multibuffer xdp_buff") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Link: https://patch.msgid.link/20250309134219.91670-2-ap420073@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In mlx5_chains_create_table(), the return value of mlx5_get_fdb_sub_ns()
and mlx5_get_flow_namespace() must be checked to prevent NULL pointer
dereferences. If either function fails, the function should log error
message with mlx5_core_warn() and return error pointer.
The VMBus driver manages the MMIO space it owns via the hyperv_mmio
resource tree. Because the synthetic video framebuffer portion of the
MMIO space is initially setup by the Hyper-V host for each guest, the
VMBus driver does an early reserve of that portion of MMIO space in the
hyperv_mmio resource tree. It saves a pointer to that resource in
fb_mmio. When a VMBus driver requests MMIO space and passes "true"
for the "fb_overlap_ok" argument, the reserved framebuffer space is
used if possible. In that case it's not necessary to do another request
against the "shadow" hyperv_mmio resource tree because that resource
was already requested in the early reserve steps.
However, the vmbus_free_mmio() function currently does no special
handling for the fb_mmio resource. When a framebuffer device is
removed, or the driver is unbound, the current code for
vmbus_free_mmio() releases the reserved resource, leaving fb_mmio
pointing to memory that has been freed. If the same or another
driver is subsequently bound to the device, vmbus_allocate_mmio()
checks against fb_mmio, and potentially gets garbage. Furthermore
a second unbind operation produces this "nonexistent resource" error
because of the unbalanced behavior between vmbus_allocate_mmio() and
vmbus_free_mmio():
[ 55.499643] resource: Trying to free nonexistent
resource <0x00000000f0000000-0x00000000f07fffff>
Fix this by adding logic to vmbus_free_mmio() to recognize when
MMIO space in the fb_mmio reserved area would be released, and don't
release it. This filtering ensures the fb_mmio resource always exists,
and makes vmbus_free_mmio() more parallel with vmbus_allocate_mmio().
Fixes: be000f93e5d7 ("drivers:hv: Track allocations of children of hv_vmbus in private resource tree") Signed-off-by: Michael Kelley <mhklinux@outlook.com> Tested-by: Saurabh Sengar <ssengar@linux.microsoft.com> Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com> Link: https://lore.kernel.org/r/20250310035208.275764-1-mhklinux@outlook.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250310035208.275764-1-mhklinux@outlook.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a Hyper-V framebuffer device is unbind, hyperv_fb driver tries to
release the framebuffer forcefully. If this framebuffer is in use it
produce the following WARN and hence this framebuffer is never released.
Fix this by moving the release of framebuffer and assosiated memory
to fb_ops.fb_destroy function, so that framebuffer framework handles
it gracefully.
While we fix this, also replace manual registrations/unregistration of
framebuffer with devm_register_framebuffer.
Fixes: 68a2d20b79b1 ("drivers/video: add Hyper-V Synthetic Video Frame Buffer Driver") Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Tested-by: Michael Kelley <mhklinux@outlook.com> Link: https://lore.kernel.org/r/1740845791-19977-3-git-send-email-ssengar@linux.microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1740845791-19977-3-git-send-email-ssengar@linux.microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The device object required in 'hvfb_release_phymem' function
for 'dma_free_coherent' can also be obtained from the 'info'
pointer, making 'hdev' parameter in 'hvfb_putmem' redundant.
Remove the unnecessary 'hdev' argument from 'hvfb_putmem'.
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com> Reviewed-by: Michael Kelley <mhklinux@outlook.com> Tested-by: Michael Kelley <mhklinux@outlook.com> Link: https://lore.kernel.org/r/1740845791-19977-2-git-send-email-ssengar@linux.microsoft.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1740845791-19977-2-git-send-email-ssengar@linux.microsoft.com>
Stable-dep-of: ea2f45ab0e53 ("fbdev: hyperv_fb: Allow graceful removal of framebuffer") Signed-off-by: Sasha Levin <sashal@kernel.org>
Gen 2 Hyper-V VMs boot via EFI and have a standard EFI framebuffer
device. When the kdump kernel runs in such a VM, loading the efifb
driver may hang because of accessing the framebuffer at the wrong
memory address.
The scenario occurs when the hyperv_fb driver in the original kernel
moves the framebuffer to a different MMIO address because of conflicts
with an already-running efifb or simplefb driver. The hyperv_fb driver
then informs Hyper-V of the change, which is allowed by the Hyper-V FB
VMBus device protocol. However, when the kexec command loads the kdump
kernel into crash memory via the kexec_file_load() system call, the
system call doesn't know the framebuffer has moved, and it sets up the
kdump screen_info using the original framebuffer address. The transition
to the kdump kernel does not go through the Hyper-V host, so Hyper-V
does not reset the framebuffer address like it would do on a reboot.
When efifb tries to run, it accesses a non-existent framebuffer
address, which traps to the Hyper-V host. After many such accesses,
the Hyper-V host thinks the guest is being malicious, and throttles
the guest to the point that it runs very slowly or appears to have hung.
When the kdump kernel is loaded into crash memory via the kexec_load()
system call, the problem does not occur. In this case, the kexec command
builds the screen_info table itself in user space from data returned
by the FBIOGET_FSCREENINFO ioctl against /dev/fb0, which gives it the
new framebuffer location.
This problem was originally reported in 2020 [1], resulting in commit 3cb73bc3fa2a ("hyperv_fb: Update screen_info after removing old
framebuffer"). This commit solved the problem by setting orig_video_isVGA
to 0, so the kdump kernel was unaware of the EFI framebuffer. The efifb
driver did not try to load, and no hang occurred. But in 2024, commit c25a19afb81c ("fbdev/hyperv_fb: Do not clear global screen_info")
effectively reverted 3cb73bc3fa2a. Commit c25a19afb81c has no reference
to 3cb73bc3fa2a, so perhaps it was done without knowing the implications
that were reported with 3cb73bc3fa2a. In any case, as of commit c25a19afb81c, the original problem came back again.
Interestingly, the hyperv_drm driver does not have this problem because
it never moves the framebuffer. The difference is that the hyperv_drm
driver removes any conflicting framebuffers *before* allocating an MMIO
address, while the hyperv_fb drivers removes conflicting framebuffers
*after* allocating an MMIO address. With the "after" ordering, hyperv_fb
may encounter a conflict and move the framebuffer to a different MMIO
address. But the conflict is essentially bogus because it is removed
a few lines of code later.
Rather than fix the problem with the approach from 2020 in commit 3cb73bc3fa2a, instead slightly reorder the steps in hyperv_fb so
conflicting framebuffers are removed before allocating an MMIO address.
Then the default framebuffer MMIO address should always be available, and
there's never any confusion about which framebuffer address the kdump
kernel should use -- it's always the original address provided by
the Hyper-V host. This approach is already used by the hyperv_drm
driver, and is consistent with the usage guidelines at the head of
the module with the function aperture_remove_conflicting_devices().
This approach also solves a related minor problem when kexec_load()
is used to load the kdump kernel. With current code, unbinding and
rebinding the hyperv_fb driver could result in the framebuffer moving
back to the default framebuffer address, because on the rebind there
are no conflicts. If such a move is done after the kdump kernel is
loaded with the new framebuffer address, at kdump time it could again
have the wrong address.
This problem and fix are described in terms of the kdump kernel, but
it can also occur with any kernel started via kexec.
See extensive discussion of the problem and solution at [2].
Reported-by: Thomas Tai <thomas.tai@oracle.com> Fixes: c25a19afb81c ("fbdev/hyperv_fb: Do not clear global screen_info") Signed-off-by: Michael Kelley <mhklinux@outlook.com> Link: https://lore.kernel.org/r/20250218230130.3207-1-mhklinux@outlook.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250218230130.3207-1-mhklinux@outlook.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a Hyper-V DRM device is probed, the driver allocates MMIO space for
the vram, and maps it cacheable. If the device removed, or in the error
path for device probing, the MMIO space is released but no unmap is done.
Consequently the kernel address space for the mapping is leaked.
Fix this by adding iounmap() calls in the device removal path, and in the
error path during device probing.
Fixes: f1f63cbb705d ("drm/hyperv: Fix an error handling path in hyperv_vmbus_probe()") Fixes: a0ab5abced55 ("drm/hyperv : Removing the restruction of VRAM allocation with PCI bar size") Signed-off-by: Michael Kelley <mhklinux@outlook.com> Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com> Tested-by: Saurabh Sengar <ssengar@linux.microsoft.com> Link: https://lore.kernel.org/r/20250210193441.2414-1-mhklinux@outlook.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250210193441.2414-1-mhklinux@outlook.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function __netpoll_send_skb() is being invoked without holding the
RCU read lock. This oversight triggers a warning message when
CONFIG_PROVE_RCU_LIST is enabled:
ATU Load operations could fail silently if there's not enough space
on the device to hold the new entry. When this happens, the symptom
depends on the unknown flood settings. If unknown multicast flood is
disabled, the multicast packets are dropped when the ATU table is
full. If unknown multicast flood is enabled, the multicast packets
will be flooded to all ports. Either way, IGMP snooping is broken
when the ATU Load operation fails silently.
Do a Read-After-Write verification after each fdb/mdb add operation
to make sure that the operation was really successful, and return
-ENOSPC otherwise.
Fixes: defb05b9b9b4 ("net: dsa: mv88e6xxx: Add support for fdb_add, fdb_del, and fdb_getnext") Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250306172306.3859214-1-Joseph.Huang@garmin.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This reverts commit 4d94f05558271654670d18c26c912da0c1c15549 which has
problems (see [1]) and is no longer needed since 581dd2dc168f
("Bluetooth: hci_event: Fix using rcu_read_(un)lock while iterating")
has reworked the code where the original bug has been found.
Passive scanning shall only be enabled when disconnecting LE links,
otherwise it may start result in triggering scanning when e.g. an ISO
link disconnects:
> HCI Event: LE Meta Event (0x3e) plen 29
LE Connected Isochronous Stream Established (0x19)
Status: Success (0x00)
Connection Handle: 257
CIG Synchronization Delay: 0 us (0x000000)
CIS Synchronization Delay: 0 us (0x000000)
Central to Peripheral Latency: 10000 us (0x002710)
Peripheral to Central Latency: 10000 us (0x002710)
Central to Peripheral PHY: LE 2M (0x02)
Peripheral to Central PHY: LE 2M (0x02)
Number of Subevents: 1
Central to Peripheral Burst Number: 1
Peripheral to Central Burst Number: 1
Central to Peripheral Flush Timeout: 2
Peripheral to Central Flush Timeout: 2
Central to Peripheral MTU: 320
Peripheral to Central MTU: 160
ISO Interval: 10.00 msec (0x0008)
...
> HCI Event: Disconnect Complete (0x05) plen 4
Status: Success (0x00)
Handle: 257
Reason: Remote User Terminated Connection (0x13)
< HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6
Extended scan: Enabled (0x01)
Filter duplicates: Enabled (0x01)
Duration: 0 msec (0x0000)
Period: 0.00 sec (0x0000)
Fixes: 9fcb18ef3acb ("Bluetooth: Introduce LE auto connect options") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A wiphy_work can be queued from the moment the wiphy is allocated and
initialized (i.e. wiphy_new_nm). When a wiphy_work is queued, the
rdev::wiphy_work is getting queued.
If wiphy_free is called before the rdev::wiphy_work had a chance to run,
the wiphy memory will be freed, and then when it eventally gets to run
it'll use invalid memory.
Fix this by canceling the work before freeing the wiphy.
Fixes: a3ee4dc84c4e ("wifi: cfg80211: add a work abstraction with special semantics") Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Link: https://patch.msgid.link/20250306123626.efd1d19f6e07.I48229f96f4067ef73f5b87302335e2fd750136c9@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The worker really shouldn't be queued for a non-running interface.
Also, if ieee80211_setup_sdata is called between queueing and executing
the wk, it will be initialized, which will corrupt wiphy_work_list.
When MSI-X is not enabled, we mask all the interrupts in the interrupt
handler and re-enable them when the interrupt thread runs. If
STATUS_INT_ENABLED is not set, we won't re-enable in the thread.
In order to get the ALIVE interrupt, we allow the ALIVE interrupt
itself, and RX as well in order to receive the ALIVE notification (which
is received as an RX from the firmware.
The problem is that STATUS_INT_ENABLED is clear until the op_mode calls
trans_fw_alive which means that until trans_fw_alive is called, any
notification from the firmware will not be received.
This became a problem when we inserted the pnvm_load exactly between the
ALIVE and trans_fw_alive.
Fix that by calling trans_fw_alive before loading the PNVM. This will
allow to get the notification from the firmware about PNVM load being
complete and continue the flow normally.
This didn't happen on MSI-X because we don't disable the interrupts in
the ISR when MSI-X is available.
The error in the log looks like this:
iwlwifi 0000:00:03.0: Timeout waiting for PNVM load!
iwlwifi 0000:00:03.0: Failed to start RT ucode: -110
iwlwifi 0000:00:03.0: WRT: Collecting data: ini trigger 13 fired (delay=0ms).
Fixes: 70d3ca86b025 ("iwlwifi: mvm: ring the doorbell and wait for PNVM load completion") Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20250306122425.0f2cf207aae1.I025d8f724b44f52eadf6c19069352eb9275613a8@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If kzalloc in gred_init returns a NULL pointer, the code follows the
error handling path, invoking gred_destroy. This, in turn, calls
gred_offload, where memset could receive a NULL pointer as input,
potentially leading to a kernel crash.
When table->opt is NULL in gred_init(), gred_change_table_def()
is not called yet, so it is not necessary to call ->ndo_setup_tc()
in gred_offload().
Signed-off-by: Jun Yang <juny24602@gmail.com> Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com> Fixes: f25c0515c521 ("net: sched: gred: dynamically allocate tc_gred_qopt_offload") Link: https://patch.msgid.link/20250305154410.3505642-1-juny24602@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to flush_work before tearing down a table from the netlink
notifier was supposed to make sure that all earlier updates (e.g. rule
add) that might reference that table have been processed.
Unfortunately, flush_work() waits for the last queued instance.
This could be an instance that is different from the one that we must
wait for.
This is because transactions are protected with a pernet mutex, but the
work item is global, so holding the transaction mutex doesn't prevent
another netns from queueing more work.
Make the work item pernet so that flush_work() will wait for all
transactions queued from this netns.
A welcome side effect is that we no longer need to wait for transaction
objects from foreign netns.
The gc work queue is still global. This seems to be ok because nft_set
structures are reference counted and each container structure owns a
reference on the net namespace.
The destroy_list is still protected by a global spinlock rather than
pernet one but the hold time is very short anyway.
v2: call cancel_work_sync before reaping the remaining tables (Pablo).
Fixes: 9f6958ba2e90 ("netfilter: nf_tables: unconditionally flush pending work before notifier") Reported-by: syzbot+5d8c5789c8cb076b2c25@syzkaller.appspotmail.com Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
nf_conncount is supposed to skip garbage collection if it has already
run garbage collection in the same jiffy. Unfortunately, this is broken
when jiffies wrap around which this patch fixes.
The problem is that last_gc in the nf_conncount_list struct is an u32,
but jiffies is an unsigned long which is 8 bytes on my systems. When
those two are compared it only works until last_gc wraps around.
See bug report: https://bugzilla.netfilter.org/show_bug.cgi?id=1778
for more details.
Ever since removing switchdev control VSI and using PF for port
representor Tx/Rx, switchdev slow-path has been working improperly after
failover in SR-IOV LAG. LAG assumes that the first uplink to be added to
the aggregate will own VFs and have switchdev configured. After
failing-over to the other uplink, representors are still configured to
Tx through the uplink they are set up on, which fails because that
uplink is now down.
On failover, update all PRs on primary uplink to use the currently
active uplink for Tx. Call netif_keep_dst(), as the secondary uplink
might not be in switchdev mode. Also make sure to call
ice_eswitch_set_target_vsi() if uplink is in LAG.
On the Rx path, representors are already working properly, because
default Tx from VFs is set to PF owning the eswitch. After failover the
same PF is receiving traffic from VFs, even though link is down.
Fixes: defd52455aee ("ice: do Tx through PF netdev in slow-path") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix aRFS (accelerated Receive Flow Steering) structures memory leak by
adding a checker to verify if aRFS memory is already allocated while
configuring VSI. aRFS objects are allocated in two cases:
- as part of VSI initialization (at probe), and
- as part of reset handling
However, VSI reconfiguration executed during reset involves memory
allocation one more time, without prior releasing already allocated
resources. This led to the memory leak with the following signature:
Fixes: 28bf26724fdb ("ice: Implement aRFS") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After switchdev is enabled and disabled later, LLDP packets sending stops,
despite working perfectly fine before and during switchdev state.
To reproduce (creating/destroying VF is what triggers the reconfiguration):
devlink dev eswitch set pci/<address> mode switchdev
echo '2' > /sys/class/net/<ifname>/device/sriov_numvfs
echo '0' > /sys/class/net/<ifname>/device/sriov_numvfs
This happens because LLDP relies on the destination override functionality.
It needs to 1) set a flag in the descriptor, 2) set the VSI permission to
make it valid. The permissions are set when the PF VSI is first configured,
but switchdev then enables it for the uplink VSI (which is always the PF)
once more when configured and disables when deconfigured, which leads to
software-generated LLDP packets being blocked.
Do not modify the destination override permissions when configuring
switchdev, as the enabled state is the default configuration that is never
modified.
Fixes: 1a1c40df2e80 ("ice: set and release switchdev environment") Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com> Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
nft_ct_pcpu_template is a per-CPU variable and relies on disabled BH for its
locking. The refcounter is read and if its value is set to one then the
refcounter is incremented and variable is used - otherwise it is already
in use and left untouched.
Without per-CPU locking in local_bh_disable() on PREEMPT_RT the
read-then-increment operation is not atomic and therefore racy.
This can be avoided by using unconditionally __refcount_inc() which will
increment counter and return the old value as an atomic operation.
In case the returned counter is not one, the variable is in use and we
need to decrement counter. Otherwise we can use it.
Use __refcount_inc() instead of read and a conditional increment.
Fixes: edee4f1e9245 ("netfilter: nft_ct: add zone id set support") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
devm_kasprintf() calls can return null pointers on failure.
But the return values were not checked in npcm8xx_gpio_fw().
Add NULL check in npcm8xx_gpio_fw(), to handle kernel NULL
pointer dereference error.
Fixes: acf4884a5717 ("pinctrl: nuvoton: add NPCM8XX pinctrl and GPIO driver") Signed-off-by: Charles Han <hanchunchao@inspur.com> Link: https://lore.kernel.org/20250212100532.4317-1-hanchunchao@inspur.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The max_registers value does not take into consideration the stride;
currently, it's set to the number of the last pin, but this does not
accurately represent the final register.
When a Hyper-V framebuffer device is removed, or the driver is unbound
from a device, any allocated and/or mapped memory must be released. In
particular, MMIO address space that was mapped to the framebuffer must
be unmapped. Current code unmaps the wrong address, resulting in an
error like:
Commit d21987d709e8 ("video: hyperv: hyperv_fb: Support deferred IO for
Hyper-V frame buffer driver") changed the kind of address stored in
info->screen_base, and the iounmap() call in hvfb_putmem() was not
updated accordingly.
Fix this by updating hvfb_putmem() to unmap the correct address.
Fixes: d21987d709e8 ("video: hyperv: hyperv_fb: Support deferred IO for Hyper-V frame buffer driver") Signed-off-by: Michael Kelley <mhklinux@outlook.com> Reviewed-by: Saurabh Sengar <ssengar@linux.microsoft.com> Link: https://lore.kernel.org/r/20250209235252.2987-1-mhklinux@outlook.com Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20250209235252.2987-1-mhklinux@outlook.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current implementation of move_pages_pte() copies source and destination
PTEs in order to detect concurrent changes to PTEs involved in the move.
However these copies are also used to unmap the PTEs, which will fail if
CONFIG_HIGHPTE is enabled because the copies are allocated on the stack.
Fix this by using the actual PTEs which were kmap()ed.
Link: https://lkml.kernel.org/r/20250226185510.2732648-3-surenb@google.com Fixes: adef440691ba ("userfaultfd: UFFDIO_MOVE uABI") Signed-off-by: Suren Baghdasaryan <surenb@google.com> Reported-by: Peter Xu <peterx@redhat.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Barry Song <21cnbao@gmail.com> Cc: Barry Song <v-songbaohua@oppo.com> Cc: David Hildenbrand <david@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jann Horn <jannh@google.com> Cc: Kalesh Singh <kaleshsingh@google.com> Cc: Liam R. Howlett <Liam.Howlett@Oracle.com> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com> Cc: Matthew Wilcow (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- If the PTE entry is a swap entry, move_swap_pte() simply copies
the PTE to the new dst_addr.
This approach is incorrect because, even if the PTE is a swap entry,
it can still reference a folio that remains in the swap cache.
This creates a race window between steps 2 and 4.
1. add_to_swap: The folio is added to the swapcache.
2. try_to_unmap: PTEs are converted to swap entries.
3. pageout: The folio is written back.
4. Swapcache is cleared.
If userfaultfd_move() occurs in the window between steps 2 and 4,
after the swap PTE has been moved to the destination, accessing the
destination triggers do_swap_page(), which may locate the folio in
the swapcache. However, since the folio's index has not been updated
to match the destination VMA, do_swap_page() will detect a mismatch.
This can result in two critical issues depending on the system
configuration.
If KSM is disabled, both small and large folios can trigger a BUG
during the add_rmap operation due to:
If KSM is enabled, Peter Xu also discovered that do_swap_page() may
trigger an unexpected CoW operation for small folios because
ksm_might_need_to_copy() allocates a new folio when the folio index
does not match linear_page_index(vma, addr).
This patch also checks the swapcache when handling swap entries. If a
match is found in the swapcache, it processes it similarly to a present
PTE.
However, there are some differences. For example, the folio is no longer
exclusive because folio_try_share_anon_rmap_pte() is performed during
unmapping.
Furthermore, in the case of swapcache, the folio has already been
unmapped, eliminating the risk of concurrent rmap walks and removing the
need to acquire src_folio's anon_vma or lock.
Note that for large folios, in the swapcache handling path, we directly
return -EBUSY since split_folio() will return -EBUSY regardless if
the folio is under writeback or unmapped. This is not an urgent issue,
so a follow-up patch may address it separately.
[v-songbaohua@oppo.com: minor cleanup according to Peter Xu] Link: https://lkml.kernel.org/r/20250226024411.47092-1-21cnbao@gmail.com Link: https://lkml.kernel.org/r/20250226001400.9129-1-21cnbao@gmail.com Fixes: adef440691ba ("userfaultfd: UFFDIO_MOVE uABI") Signed-off-by: Barry Song <v-songbaohua@oppo.com> Acked-by: Peter Xu <peterx@redhat.com> Reviewed-by: Suren Baghdasaryan <surenb@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Axel Rasmussen <axelrasmussen@google.com> Cc: Brian Geffon <bgeffon@google.com> Cc: Christian Brauner <brauner@kernel.org> Cc: David Hildenbrand <david@redhat.com> Cc: Hugh Dickins <hughd@google.com> Cc: Jann Horn <jannh@google.com> Cc: Kalesh Singh <kaleshsingh@google.com> Cc: Liam R. Howlett <Liam.Howlett@oracle.com> Cc: Lokesh Gidra <lokeshgidra@google.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Mike Rapoport (IBM) <rppt@kernel.org> Cc: Nicolas Geoffray <ngeoffray@google.com> Cc: Ryan Roberts <ryan.roberts@arm.com> Cc: Shuah Khan <shuah@kernel.org> Cc: ZhangPeng <zhangpeng362@huawei.com> Cc: Tangquan Zheng <zhengtangquan@oppo.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ surenb: resolved merged conflict caused by the difference in
move_swap_pte() arguments ] Signed-off-by: Suren Baghdasaryan <surenb@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The allocation of the scatter gather data structure should be done
based on the number of memory chunks that need to be mapped, and it
is not dependent on the overall payload length. Fix it.
In addition, as the skb_to_sgvec() function returns an 'int' do not
assign it to an 'unsigned int' as otherwise the error check would be
useless.
Fixes: 7f5e3038f029 ("wifi: iwlwifi: map entire SKB when sending AMSDUs") Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20250306122425.8c0e23a3d583.I3cb4d6768c9d28ce3da6cd0a6c65466176cfc1ee@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per the "Processor Specification Update" documentations referred by
the intel-microcode-20240312 release note, this microcode release has
fixed the issue for all affected models.
So don't disable PCID if the microcode is new enough. The precise
minimum microcode revision fixing the issue was provided by Pawan
Intel.
Availability of the gettid definition across glibc versions supported by
BPF selftests is not certain. Currently, all users in the tree open-code
syscall to gettid. Convert them to a common macro definition.
Max Makarov reported kernel panic [1] in perf user callchain code.
The reason for that is the race between uprobe_free_utask and bpf
profiler code doing the perf user stack unwind and is triggered
within uprobe_free_utask function:
- after current->utask is freed and
- before current->utask is set to NULL
If find_linux_pte fails, IRQs will not be restored. This is unlikely
to happen in practice since it would have been reported as hanging
hosts, but it should of course be fixed anyway.
Cc: stable@vger.kernel.org Reported-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This list started as a "when to prefer `expect`" list, but at some point
during writing I changed it to a "prefer `expect` unless..." one. However,
the first bullet remained, which does not make sense anymore.
Thus remove it. In addition, fix nearby typo.
Fixes: 04866494e936 ("Documentation: rust: discuss `#[expect(...)]` in the guidelines") Reviewed-by: Alice Ryhl <aliceryhl@google.com> Reviewed-by: Andreas Hindborg <a.hindborg@kernel.org> Link: https://lore.kernel.org/r/20241117133127.473937-1-ojeda@kernel.org Signed-off-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In H2CTermReq, a FES with value 0x05 means "R2T Limit Exceeded"; but
in C2HTermReq the same value has a different meaning (Data Transfer Limit
Exceeded).
Fixes: 84e009042d0f ("nvme-tcp: add basic support for the C2HTermReq PDU") Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The alternative path leads to a build error after a recent change:
sound/pci/hda/patch_realtek.c: In function 'alc233_fixup_lenovo_low_en_micmute_led':
include/linux/stddef.h:9:14: error: called object is not a function or function pointer
9 | #define NULL ((void *)0)
| ^
sound/pci/hda/patch_realtek.c:5041:49: note: in expansion of macro 'NULL'
5041 | #define alc233_fixup_lenovo_line2_mic_hotkey NULL
| ^~~~
sound/pci/hda/patch_realtek.c:5063:9: note: in expansion of macro 'alc233_fixup_lenovo_line2_mic_hotkey'
5063 | alc233_fixup_lenovo_line2_mic_hotkey(codec, fix, action);
Using IS_REACHABLE() is somewhat questionable here anyway since it
leads to the input code not working when the HDA driver is builtin
but input is in a loadable module. Replace this with a hard compile-time
dependency on CONFIG_INPUT. In practice this won't chance much
other than solve the compiler error because it is rare to require
sound output but no input support.
Fixes: f603b159231b ("ALSA: hda/realtek - add supported Mic Mute LED for Lenovo platform") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Link: https://patch.msgid.link/20250304142620.582191-1-arnd@kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The headercheck tries to call clang with a mix of compiler arguments
that don't include the target architecture. When building e.g. x86
headers on arm64, this produces a warning like
Max Kellermann [Fri, 14 Feb 2025 13:12:25 +0000 (14:12 +0100)]
fs/netfs/read_collect: fix crash due to uninitialized `prev` variable
[ Just like the other two netfs patches I sent yesterday, this one
doesn't apply to v6.14 as it was obsoleted by commit e2d46f2ec332
("netfs: Change the read result collector to only use one work item"). ]
When checking whether the edges of adjacent subrequests touch, the
`prev` variable is deferenced, but it might not have been initialized.
This causes crashes like this one:
Max Kellermann [Mon, 10 Feb 2025 22:31:44 +0000 (23:31 +0100)]
fs/netfs/read_pgpriv2: skip folio queues without `marks3`
[ Note this patch doesn't apply to v6.14 as it was obsoleted by commit e2d46f2ec332 ("netfs: Change the read result collector to only use one
work item"). ]
At the beginning of the function, folio queues with marks3==0 are
skipped, but after that, the `marks3` field is ignored. If one such
queue is found, `slot` is set to 64 (because `__ffs(0)==64`), leading
to a buffer overflow in the folioq_folio() call. The resulting crash
may look like this:
arm64 supports multiple huge_pte sizes. Some of the sizes are covered by
a single pte entry at a particular level (PMD_SIZE, PUD_SIZE), and some
are covered by multiple ptes at a particular level (CONT_PTE_SIZE,
CONT_PMD_SIZE). So the function has to figure out the size from the
huge_pte pointer. This was previously done by walking the pgtable to
determine the level and by using the PTE_CONT bit to determine the
number of ptes at the level.
But the PTE_CONT bit is only valid when the pte is present. For
non-present pte values (e.g. markers, migration entries), the previous
implementation was therefore erroneously determining the size. There is
at least one known caller in core-mm, move_huge_pte(), which may call
huge_ptep_get_and_clear() for a non-present pte. So we must be robust to
this case. Additionally the "regular" ptep_get_and_clear() is robust to
being called for non-present ptes so it makes sense to follow the
behavior.
Fix this by using the new sz parameter which is now provided to the
function. Additionally when clearing each pte in a contig range, don't
gather the access and dirty bits if the pte is not present.
An alternative approach that would not require API changes would be to
store the PTE_CONT bit in a spare bit in the swap entry pte for the
non-present case. But it felt cleaner to follow other APIs' lead and
just pass in the size.
As an aside, PTE_CONT is bit 52, which corresponds to bit 40 in the swap
entry offset field (layout of non-present pte). Since hugetlb is never
swapped to disk, this field will only be populated for markers, which
always set this bit to 0 and hwpoison swap entries, which set the offset
field to a PFN; So it would only ever be 1 for a 52-bit PVA system where
memory in that high half was poisoned (I think!). So in practice, this
bit would almost always be zero for non-present ptes and we would only
clear the first entry if it was actually a contiguous block. That's
probably a less severe symptom than if it was always interpreted as 1
and cleared out potentially-present neighboring PTEs.
Cc: stable@vger.kernel.org Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit") Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Link: https://lore.kernel.org/r/20250226120656.2400136-3-ryan.roberts@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to fix a bug, arm64 needs to be told the size of the huge page
for which the huge_pte is being cleared in huge_ptep_get_and_clear().
Provide for this by adding an `unsigned long sz` parameter to the
function. This follows the same pattern as huge_pte_clear() and
set_huge_pte_at().
This commit makes the required interface modifications to the core mm as
well as all arches that implement this function (arm64, loongarch, mips,
parisc, powerpc, riscv, s390, sparc). The actual arm64 bug will be fixed
in a separate commit.
Cc: stable@vger.kernel.org Fixes: 66b3923a1a0f ("arm64: hugetlb: add support for PTE contiguous bit") Acked-by: David Hildenbrand <david@redhat.com> Reviewed-by: Alexandre Ghiti <alexghiti@rivosinc.com> # riscv Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Ryan Roberts <ryan.roberts@arm.com> Acked-by: Alexander Gordeev <agordeev@linux.ibm.com> # s390 Link: https://lore.kernel.org/r/20250226120656.2400136-2-ryan.roberts@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clear reset status flag, to keep error status register clean after reset
(ad3552r manual, rev B table 38).
Reset error flag was left to 1, so debugging registers, the "Error
Status Register" was dirty (0x01). It is important to clear this bit, so
if there is any reset event over normal working mode, it is possible to
detect it.
When a weak pull-up is present on the SDO line, regmap_update_bits fails
to write both the SOFTRESET and SDOACTIVE bits because it incorrectly
reads them as already set.
Since the soft reset disables the SDO line, performing a
read-modify-write operation on ADI_SPI_CONFIG_A to enable the SDO line
doesn't make sense. This change directly writes to the register instead
of using regmap_update_bits.
In the "pmcmd_ioctl" function, three memory objects allocated by
kmalloc are initialized by "hcall_get_cpu_state", which are then
copied to user space. The initializer is indeed implemented in
"acrn_hypercall2" (arch/x86/include/asm/acrn.h). There is a risk of
information leakage due to uninitialized bytes.
Fixes: 3d679d5aec64 ("virt: acrn: Introduce interfaces to query C-states and P-states allowed by hypervisor") Signed-off-by: Haoyu Li <lihaoyu499@gmail.com> Cc: stable <stable@kernel.org> Acked-by: Fei Li <fei1.li@intel.com> Link: https://lore.kernel.org/r/20250130115811.92424-1-lihaoyu499@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev_id value in the GPIO lookup table must match to
the device instance name, which in this case is combined
of name and platform device ID, i.e. "spi_gpio.1". But
the table assumed that there was no platform device ID
defined, which is wrong. Fix the dev_id value accordingly.
There are multiple places from where the recovery work gets scheduled
asynchronously. Also, there are multiple places where the caller waits
synchronously for the recovery to be completed. One such place is during
the PM shutdown() callback.
If the device is not alive during recovery_work, it will try to reset the
device using pci_reset_function(). This function internally will take the
device_lock() first before resetting the device. By this time, if the lock
has already been acquired, then recovery_work will get stalled while
waiting for the lock. And if the lock was already acquired by the caller
which waits for the recovery_work to be completed, it will lead to
deadlock.
This is what happened on the X1E80100 CRD device when the device died
before shutdown() callback. Driver core calls the driver's shutdown()
callback while holding the device_lock() leading to deadlock.
And this deadlock scenario can occur on other paths as well, like during
the PM suspend() callback, where the driver core would hold the
device_lock() before calling driver's suspend() callback. And if the
recovery_work was already started, it could lead to deadlock. This is also
observed on the X1E80100 CRD.
So to fix both issues, use pci_try_reset_function() in recovery_work. This
function first checks for the availability of the device_lock() before
trying to reset the device. If the lock is available, it will acquire it
and reset the device. Otherwise, it will return -EAGAIN. If that happens,
recovery_work will fail with the error message "Recovery failed" as not
much could be done.
In case of interrupt delay for any reason, slim_do_transfer()
returns timeout error but the transaction ID (TID) is not freed.
This results into invalid memory access inside
qcom_slim_ngd_rx_msgq_cb() due to invalid TID.
Fix the issue by freeing the TID in slim_do_transfer() before
returning timeout error to avoid invalid memory access.
Commit bac3b10b78e5 ("driver core: fw_devlink: Stop trying to optimize
cycle detection logic") introduced a new struct device *con_dev and a
get_dev_from_fwnode() call to get it, but without adding a corresponding
put_device().
When creating sysfs files fail, the allocated minor must be freed such that
it can be later reused. That is specially harmful for static minor numbers,
since those would always fail to register later on.
Fixes: 6d04d2b554b1 ("misc: misc_minor_alloc to use ida for all dynamic/misc dynamic minors") Cc: stable <stable@kernel.org> Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@igalia.com> Link: https://lore.kernel.org/r/20250123123249.4081674-5-cascardo@igalia.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
