Change a bunch of arguments of wrapper functions which pass signed
integer to an unsigned integer which might cause undefined behaviors
when sign integer overflow.
A race condition between threads updating mountpoint reference counter
affects longterm releases 4.4.220, 4.9.220, 4.14.177 and 4.19.118.
The mountpoint reference counter corruption may occur when:
* one thread increments m_count member of struct mountpoint
[under namespace_sem, but not holding mount_lock]
pivot_root()
* another thread simultaneously decrements the same m_count
[under mount_lock, but not holding namespace_sem]
put_mountpoint()
unhash_mnt()
umount_mnt()
mntput_no_expire()
To fix this race condition, grab mount_lock before updating m_count in
pivot_root().
Reference: CVE-2020-12114 Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Piotr Krysiuk <piotras@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XADC has two internal ADCs. Depending on the mode it is operating in
either one or both of them are used. The device manual calls this
continuous (one ADC) and simultaneous (both ADCs) mode.
The meaning of the sequencing register for the aux channels changes
depending on the mode.
In continuous mode each bit corresponds to one of the 16 aux channels. And
the single ADC will convert them one by one in order.
In simultaneous mode the aux channels are split into two groups the first 8
channels are assigned to the first ADC and the other 8 channels to the
second ADC. The upper 8 bits of the sequencing register are unused and the
lower 8 bits control both ADCs. This means a bit needs to be set if either
the corresponding channel from the first group or the second group (or
both) are set.
Currently the driver does not have the special handling required for
simultaneous mode. Add it.
When enabling the trigger and unmasking the end-of-sequence (EOS) interrupt
the EOS interrupt should be cleared from the status register. Otherwise it
is possible that it was still set from a previous capture. If that is the
case the interrupt would fire immediately even though no conversion has
been done yet and stale data is being read from the device.
The old code only clears the interrupt if the interrupt was previously
unmasked. Which does not make much sense since the interrupt is always
masked at this point and in addition masking the interrupt does not clear
the interrupt from the status register. So the clearing needs to be done
unconditionally.
The check for shutting down the second ADC is inverted. This causes it to
be powered down when it should be enabled. As a result channels that are
supposed to be handled by the second ADC return invalid conversion results.
The commit 3c6fd1f07ed0 ("ALSA: hda: Add driver blacklist") added a
new blacklist for the devices that are known to have empty codecs, and
one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f).
However, it turned out that the very same PCI SSID is used for the
previous model that does have the valid HD-audio codecs and the change
broke the sound on it.
This patch reverts the corresponding entry as a temporary solution.
Although Zenith II and co will see get the empty HD-audio bus again,
it'd be merely resource wastes and won't affect the functionality,
so it's no end of the world. We'll need to address this later,
e.g. by either switching to DMI string matching or using PCI ID &
SSID pairs.
IPSKB_XFRM_TRANSFORMED and IP6SKB_XFRM_TRANSFORMED are skb flags set by
xfrm code to tell other skb handlers that the packet has been passed
through the xfrm output functions. Simplify the code and just always
set them rather than conditionally based on netfilter enabled thus
making the flag available for other users.
Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When team mode is changed or set, the team_mode_get() is called to check
whether the mode module is inserted or not. If the mode module is not
inserted, it calls the request_module().
In the request_module(), it creates a child process, which is
the "modprobe" process and waits for the done of the child process.
At this point, the following locks were used.
down_read(&cb_lock()); by genl_rcv()
genl_lock(); by genl_rcv_msc()
rtnl_lock(); by team_nl_cmd_options_set()
mutex_lock(&team->lock); by team_nl_team_get()
Concurrently, the team module could be removed by rmmod or "modprobe -r"
The __exit function of team module is team_module_exit(), which calls
team_nl_fini() and it tries to acquire following locks.
down_write(&cb_lock);
genl_lock();
Because of the genl_lock() and cb_lock, this process can't be finished
earlier than request_module() routine.
The problem secenario.
CPU0 CPU1
team_mode_get
request_module()
modprobe -r team_mode_roundrobin
team <--(B)
modprobe team <--(A)
team_mode_roundrobin
By request_module(), the "modprobe team_mode_roundrobin" command
will be executed. At this point, the modprobe process will decide
that the team module should be inserted before team_mode_roundrobin.
Because the team module is being removed.
By the module infrastructure, the same module insert/remove operations
can't be executed concurrently.
So, (A) waits for (B) but (B) also waits for (A) because of locks.
So that the hang occurs at this point.
Test commands:
while :
do
teamd -d &
killall teamd &
modprobe -rv team_mode_roundrobin &
done
The approach of this patch is to hold the reference count of the team
module if the team module is compiled as a module. If the reference count
of the team module is not zero while request_module() is being called,
the team module will not be removed at that moment.
So that the above scenario could not occur.
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
x25_lapb_receive_frame() invokes x25_get_neigh(), which returns a
reference of the specified x25_neigh object to "nb" with increased
refcnt.
When x25_lapb_receive_frame() returns, local variable "nb" becomes
invalid, so the refcount should be decreased to keep refcount balanced.
The reference counting issue happens in one path of
x25_lapb_receive_frame(). When pskb_may_pull() returns false, the
function forgets to decrease the refcnt increased by x25_get_neigh(),
causing a refcnt leak.
Fix this issue by calling x25_neigh_put() when pskb_may_pull() returns
false.
Fixes: cb101ed2c3c7 ("x25: Handle undersized/fragmented skbs") Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nr_add_node() invokes nr_neigh_get_dev(), which returns a local
reference of the nr_neigh object to "nr_neigh" with increased refcnt.
When nr_add_node() returns, "nr_neigh" becomes invalid, so the refcount
should be decreased to keep refcount balanced.
The issue happens in one normal path of nr_add_node(), which forgets to
decrease the refcnt increased by nr_neigh_get_dev() and causes a refcnt
leak. It should decrease the refcnt before the function returns like
other normal paths do.
Fix this issue by calling nr_neigh_put() before the nr_add_node()
returns.
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the macvlan_device_event(), the list_first_entry_or_null() is used.
This function could return null pointer if there is no node.
But, the macvlan module doesn't check the null pointer.
So, null-ptr-deref would occur.
The problem scenario.
If dummy1 is removed,
1. ->dellink() of dummy1 is called.
2. NETDEV_UNREGISTER of dummy1 notification is sent to macvlan module.
3. ->dellink() of macvlan1 is called.
4. NETDEV_UNREGISTER of macvlan1 notification is sent to bond module.
5. __bond_release_one() is called and it internally calls
dev_set_mac_address().
6. dev_set_mac_address() calls the ->ndo_set_mac_address() of macvlan1,
which is macvlan_set_mac_address().
7. macvlan_set_mac_address() calls the dev_set_mac_address() with dummy1.
8. NETDEV_CHANGEADDR of dummy1 is sent to macvlan module.
9. In the macvlan_device_event(), it calls list_first_entry_or_null().
At this point, dummy1 and macvlan1 were removed.
So, list_first_entry_or_null() will return NULL.
Test commands:
ip netns add nst
ip netns exec nst ip link add bond0 type bond
for i in {0..10}
do
ip netns exec nst ip link add dummy$i type dummy
ip netns exec nst ip link add macvlan$i link dummy$i \
type macvlan mode passthru
ip netns exec nst ip link set macvlan$i master bond0
done
ip netns del nst
Fixes: e289fd28176b ("macvlan: fix the problem when mac address changes for passthru mode") Reported-by: syzbot+5035b1f9dc7ea4558d5a@syzkaller.appspotmail.com Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a macsec interface is created, the mtu is calculated with the lower
interface's mtu value.
If the mtu of lower interface is lower than the length, which is needed
by macsec interface, macsec's mtu value will be overflowed.
So, if the lower interface's mtu is too low, macsec interface's mtu
should be set to 0.
Test commands:
ip link add dummy0 mtu 10 type dummy
ip link add macsec0 link dummy0 type macsec
ip link show macsec0
Before:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 4294967274
After:
11: macsec0@dummy0: <BROADCAST,MULTICAST,M-DOWN> mtu 0
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation") fixed a
problem found by syzbot an unfortunate logic error meant that it
also broke IPV6_ADDRFORM.
Rearrange the checks so that the earlier test is just one of the series
of checks made before moving the socket from IPv6 to IPv4.
Fixes: b6f6118901d1 ("ipv6: restrict IPV6_ADDRFORM operation") Signed-off-by: John Haxby <john.haxby@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously Clock PM could not be re-enabled after being disabled by
pci_disable_link_state() because clkpm_capable was reset. Change this by
adding a clkpm_disable field similar to aspm_disable.
The newer 2711 and 7211 chips have two PWM controllers and failure to
dynamically allocate the PWM base would prevent the second PWM
controller instance being probed for succeeding with an -EEXIST error
from alloc_pwms().
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should always be disabled after the removal of the
PWM chip, even if the latter failed.
The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The io_subchannel driver will do so when the associated
ccw_device has been registered -- but unconditionally, so more
ADD uevents will be generated if a subchannel has been unbound
from the io_subchannel driver and later rebound.
To fix this, only generate the ADD event if uevents were still
suppressed for the device.
Fixes: fa1a8c23eb7d ("s390: cio: Delay uevents for subchannels")
Message-Id: <20200327124503.9794-2-cohuck@redhat.com> Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com> Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com> Reviewed-by: Boris Fiuczynski <fiuczy@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the daemon is restarted or crashes while logging out of a session, the
unbind session event sent by the kernel is not processed and is lost. When
the daemon starts again, the session can't be unbound because the daemon is
waiting for the event message. However, the kernel has already logged out
and the event will not be resent.
When iscsid restart is complete, logout session reports error:
Logging out of session [sid: 6, target: iqn.xxxxx, portal: xx.xx.xx.xx,3260]
iscsiadm: Could not logout of [sid: 6, target: iscsiadm -m node iqn.xxxxx, portal: xx.xx.xx.xx,3260].
iscsiadm: initiator reported error (9 - internal error)
iscsiadm: Could not logout of all requested sessions
Make sure the unbind event is emitted.
[mkp: commit desc and applied by hand since patch was mangled]
Runtime PM should be enabled before calling pwmchip_add(), as PWM users
can appear immediately after the PWM chip has been added.
Likewise, Runtime PM should be disabled after the removal of the PWM
chip.
1. try_get_cap_refs() fails to get caps and finds that mds_wanted
does not include what it wants. It returns -ESTALE.
2. ceph_get_caps() calls ceph_renew_caps(). ceph_renew_caps() finds
that inode has cap, so it calls ceph_check_caps().
3. ceph_check_caps() finds that issued caps (without checking if it's
stale) already includes caps wanted by open file, so it skips
updating wanted caps.
Above events can cause an infinite loop inside ceph_get_caps().
Return the error returned by ceph_mdsc_do_request(). Otherwise,
r_target_inode ends up being NULL this ends up returning ENOENT
regardless of the error.
BUG: KASAN: slab-out-of-bounds in lpfc_unreg_login+0x7c/0xc0 [lpfc]
Read of size 2 at addr ffff889fc7c50a22 by task lpfc_worker_3/6676
...
Call Trace:
dump_stack+0x96/0xe0
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
print_address_description.constprop.6+0x1b/0x220
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
__kasan_report.cold.9+0x37/0x7c
? lpfc_unreg_login+0x7c/0xc0 [lpfc]
kasan_report+0xe/0x20
lpfc_unreg_login+0x7c/0xc0 [lpfc]
lpfc_sli_def_mbox_cmpl+0x334/0x430 [lpfc]
...
When processing the completion of a "Reg Rpi" login mailbox command in
lpfc_sli_def_mbox_cmpl, a call may be made to lpfc_unreg_login. The vpi is
extracted from the completing mailbox context and passed as an input for
the next. However, the vpi stored in the mailbox command context is an
absolute vpi, which for SLI4 represents both base + offset. When used with
a non-zero base component, (function id > 0) this results in an
out-of-range access beyond the allocated phba->vpi_ids array.
Fix by subtracting the function's base value to get an accurate vpi number.
Link: https://lore.kernel.org/r/20200322181304.37655-2-jsmart2021@gmail.com Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the watchdog core does not initialize the last_hw_keepalive
time during watchdog startup. This will cause the watchdog to be pinged
immediately if enough time has passed from the system boot-up time, and
some types of watchdogs like K3 RTI does not like this.
To avoid the issue, setup the last_hw_keepalive time during watchdog
startup.
Removed info log-message if ipip tunnel registration fails during
module-initialization: it adds nothing to the error message that is
written on all failures.
Fixes: dd9ee3444014e ("vti4: Fix a ipip packet processing bug in 'IPCOMP' virtual tunnel") Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/crypto/mxs-dcp.c:39:15: warning:
symbol 'sha1_null_hash' was not declared. Should it be static?
drivers/crypto/mxs-dcp.c:43:15: warning:
symbol 'sha256_null_hash' was not declared. Should it be static?
Commit 8f659a03a0ba ("net: ipv4: fix for a race condition in
raw_sendmsg") fixed the issue of possibly inconsistent ->hdrincl handling
due to concurrent updates by reading this bit-field member into a local
variable and using the thus stabilized value in subsequent tests.
However, aforementioned commit also adds the (correct) comment that
/* hdrincl should be READ_ONCE(inet->hdrincl)
* but READ_ONCE() doesn't work with bit fields
*/
because as it stands, the compiler is free to shortcut or even eliminate
the local variable at its will.
Note that I have not seen anything like this happening in reality and thus,
the concern is a theoretical one.
However, in order to be on the safe side, emulate a READ_ONCE() on the
bit-field by doing it on the local 'hdrincl' variable itself:
int hdrincl = inet->hdrincl;
hdrincl = READ_ONCE(hdrincl);
This breaks the chain in the sense that the compiler is not allowed
to replace subsequent reads from hdrincl with reloads from inet->hdrincl.
Fixes: 8f659a03a0ba ("net: ipv4: fix for a race condition in raw_sendmsg") Signed-off-by: Nicolai Stange <nstange@suse.de> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extents are cached in read_extent_tree_block(); as a result, extents
are not cached for inodes with depth == 0 when we try to find the
extent using ext4_find_extent(). The result of the lookup is cached
in ext4_map_blocks() but is only a subset of the extent on disk. As a
result, the contents of extents status cache can get very badly
fragmented for certain workloads, such as a random 4k read workload.
File size of /mnt/test is 33554432 (8192 blocks of 4096 bytes)
ext: logical_offset: physical_offset: length: expected: flags:
0: 0.. 8191: 40960.. 49151: 8192: last,eof
$ perf record -e 'ext4:ext4_es_*' /root/bin/fio --name=t --direct=0 --rw=randread --bs=4k --filesize=32M --size=32M --filename=/mnt/test
$ perf script | grep ext4_es_insert_extent | head -n 10
fio 131 [000] 13.975421: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [494/1) mapped 41454 status W
fio 131 [000] 13.975939: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6064/1) mapped 47024 status W
fio 131 [000] 13.976467: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6907/1) mapped 47867 status W
fio 131 [000] 13.976937: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3850/1) mapped 44810 status W
fio 131 [000] 13.977440: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3292/1) mapped 44252 status W
fio 131 [000] 13.977931: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [6882/1) mapped 47842 status W
fio 131 [000] 13.978376: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [3117/1) mapped 44077 status W
fio 131 [000] 13.978957: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [2896/1) mapped 43856 status W
fio 131 [000] 13.979474: ext4:ext4_es_insert_extent: dev 253,0 ino 12 es [7479/1) mapped 48439 status W
Fix this by caching the extents for inodes with depth == 0 in
ext4_find_extent().
[ Renamed ext4_es_cache_extents() to ext4_cache_extents() since this
newly added function is not in extents_cache.c, and to avoid
potential visual confusion with ext4_es_cache_extent(). -TYT ]
In the __getcpu function, lsl is using the wrong target and destination
registers. Luckily, the compiler tends to choose %eax for both variables,
so it has been working so far.
Fixes: a582c540ac1b ("x86/vdso: Use RDPID in preference to LSL when available") Signed-off-by: Samuel Neves <sneves@dei.uc.pt> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20180901201452.27828-1-sneves@dei.uc.pt Signed-off-by: Nobuhiro Iwamatsu (CIP) <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
x86/microcode/intel: replace sync_core() with native_cpuid_reg(eax)
On Intel it is required to do CPUID(1) before reading the microcode
revision MSR. Current code in 4.4 an 4.9 relies on sync_core() to call
CPUID, unfortunately on 32 bit machines code inside sync_core() always
jumps past CPUID instruction as it depends on data structure boot_cpu_data
witch are not populated correctly so early in boot sequence.
It depends on:
commit 5dedade6dfa2 ("x86/CPU: Add native CPUID variants returning a single
datum")
This patch is for 4.4 but also should apply to 4.9
The variable 'name' is released multiple times in the error path,
which may cause double free issues.
This problem is avoided by adding a goto label to release the memory
uniformly. And this change also makes the code a bit more cleaner.
This function is only called from lpddr_probe(). We free "lpddr" both
here and in the caller, so it's a double free. The best place to free
"lpddr" is in lpddr_probe() so let's delete this one.
The __torture_print_stats() function in locktorture.c carefully
initializes local variable "min" to statp[0].n_lock_acquired, but
then compares it to statp[i].n_lock_fail. Given that the .n_lock_fail
field should normally be zero, and given the initialization, it seems
reasonable to display the maximum and minimum number acquisitions
instead of miscomputing the maximum and minimum number of failures.
This commit therefore switches from failures to acquisitions.
And this turns out to be not only a day-zero bug, but entirely my
own fault. I hate it when that happens!
Fixes: 0af3fe1efa53 ("locktorture: Add a lock-torture kernel module") Reported-by: Will Deacon <will@kernel.org> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Acked-by: Will Deacon <will@kernel.org> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Josh Triplett <josh@joshtriplett.org> Cc: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ev_byte_channel_send() assumes that its third argument is a 16 byte
array. Some places where it is called it may not be (or we can't
easily tell if it is). Newer compilers have started producing warnings
about this, so make sure we actually pass a 16 byte array.
There may be more elegant solutions to this, but the driver is quite
old and hasn't been updated in many years.
The warnings (from a powerpc allyesconfig build) are:
In file included from include/linux/byteorder/big_endian.h:5,
from arch/powerpc/include/uapi/asm/byteorder.h:14,
from include/asm-generic/bitops/le.h:6,
from arch/powerpc/include/asm/bitops.h:250,
from include/linux/bitops.h:29,
from include/linux/kernel.h:12,
from include/asm-generic/bug.h:19,
from arch/powerpc/include/asm/bug.h:109,
from include/linux/bug.h:5,
from include/linux/mmdebug.h:5,
from include/linux/gfp.h:5,
from include/linux/slab.h:15,
from drivers/tty/ehv_bytechan.c:24:
drivers/tty/ehv_bytechan.c: In function ‘ehv_bc_udbg_putc’:
arch/powerpc/include/asm/epapr_hcalls.h:298:20: warning: array subscript 1 is outside array bounds of ‘const char[1]’ [-Warray-bounds]
298 | r6 = be32_to_cpu(p[1]);
include/uapi/linux/byteorder/big_endian.h:40:51: note: in definition of macro ‘__be32_to_cpu’
40 | #define __be32_to_cpu(x) ((__force __u32)(__be32)(x))
| ^
arch/powerpc/include/asm/epapr_hcalls.h:298:7: note: in expansion of macro ‘be32_to_cpu’
298 | r6 = be32_to_cpu(p[1]);
| ^~~~~~~~~~~
drivers/tty/ehv_bytechan.c:166:13: note: while referencing ‘data’
166 | static void ehv_bc_udbg_putc(char c)
| ^~~~~~~~~~~~~~~~
Fixes: dcd83aaff1c8 ("tty/powerpc: introduce the ePAPR embedded hypervisor byte channel driver") Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Tested-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
[mpe: Trim warnings from change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200109183912.5fcb52aa@canb.auug.org.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "fix" struct has a 2 byte hole after ->ywrapstep and the
"fix = info->fix;" assignment doesn't necessarily clear it. It depends
on the compiler. The solution is just to replace the assignment with an
memcpy().
Fixes: 1f5e31d7e55a ("fbmem: don't call copy_from/to_user() with mutex held") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Andrea Righi <righi.andrea@gmail.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: Peter Rosin <peda@axentia.se> Cc: Jani Nikula <jani.nikula@intel.com> Cc: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200113100132.ixpaymordi24n3av@kili.mountain Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPA of the GCR3 table root pointer[51:31] masks 20 bits. However,
this requires 21 bits (Please see the AMD IOMMU specification).
This leads to the potential failure when the bit 51 of SPA of
the GCR3 table root pointer is 1'.
Signed-off-by: Adrian Huang <ahuang12@lenovo.com> Fixes: 52815b75682e2 ("iommu/amd: Add support for IOMMUv2 domain mode") Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "cmd" comes from the user and it can be up to 255. It it's more
than the number of bits in long, it results out of bounds read when we
check test_bit(cmd, &cmd_mask). The highest valid value for "cmd" is
ND_CMD_CALL (10) so I added a compare against that.
Fixes: 62232e45f4a2 ("libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20200225162055.amtosfy7m35aivxg@kili.mountain Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building without extra debugging, (and with another patch that uses
no_printk() instead of <empty> for the ext2-xattr debug-print macros,
this build error happens:
../fs/ext2/xattr.c: In function ‘ext2_xattr_cache_insert’:
../fs/ext2/xattr.c:869:18: error: ‘ext2_xattr_cache’ undeclared (first use in
this function); did you mean ‘ext2_xattr_list’?
atomic_read(&ext2_xattr_cache->c_entry_count));
Fix the problem by removing cached entry count from the debug message
since otherwise we'd have to export the mbcache structure just for that.
Fixes: be0726d33cb8 ("ext2: convert to mbcache2") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
When EXT2_ATTR_DEBUG is not defined, modify the 2 debug macros
to use the no_printk() macro instead of <nothing>.
This fixes gcc warnings when -Wextra is used:
../fs/ext2/xattr.c:252:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../fs/ext2/xattr.c:258:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../fs/ext2/xattr.c:330:42: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
../fs/ext2/xattr.c:872:45: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
I have verified that the only object code change (with gcc 7.5.0) is
the reversal of some instructions from 'cmp a,b' to 'cmp b,a'.
We have to properly retry again by returning -EINVAL immediately in case
somebody else instantiated the table concurrently. We missed to add the
goto in this function only. The code now matches the other, similar
shadowing functions.
We are overwriting an existing region 2 table entry. All allocated pages
are added to the crst_list to be freed later, so they are not lost
forever. However, when unshadowing the region 2 table, we wouldn't trigger
unshadowing of the original shadowed region 3 table that we replaced. It
would get unshadowed when the original region 3 table is modified. As it's
not connected to the page table hierarchy anymore, it's not going to get
used anymore. However, for a limited time, this page table will stick
around, so it's in some sense a temporary memory leak.
Identified by manual code inspection. I don't think this classifies as
stable material.
Fixes: 998f637cc4b9 ("s390/mm: avoid races on region/segment/page table shadowing") Signed-off-by: David Hildenbrand <david@redhat.com> Link: https://lore.kernel.org/r/20200403153050.20569-4-david@redhat.com Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
compiletime_assert() uses __LINE__ to create a unique function name. This
means that if you have more than one BUILD_BUG_ON() in the same source
line (which can happen if they appear e.g. in a macro), then the error
message from the compiler might output the wrong condition.
./include/linux/compiler.h:350:38: error: call to `__compiletime_assert_9' declared with attribute error: BUILD_BUG_ON failed: 0
_compiletime_assert(condition, msg, __compiletime_assert_, __LINE__)
However, it was not the BUILD_BUG_ON(0) that failed, so it should say 1
instead of 0. With this patch, we use __COUNTER__ instead of __LINE__, so
each BUILD_BUG_ON() gets a different function name and the correct
condition is printed:
./include/linux/compiler.h:350:38: error: call to `__compiletime_assert_0' declared with attribute error: BUILD_BUG_ON failed: 1
_compiletime_assert(condition, msg, __compiletime_assert_, __COUNTER__)
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Daniel Santos <daniel.santos@pobox.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Cc: Ian Abbott <abbotti@mev.co.uk> Cc: Joe Perches <joe@perches.com> Link: http://lkml.kernel.org/r/20200331112637.25047-1-vegard.nossum@oracle.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"vm_committed_as.count" could be accessed concurrently as reported by
KCSAN,
BUG: KCSAN: data-race in __vm_enough_memory / percpu_counter_add_batch
write to 0xffffffff9451c538 of 8 bytes by task 65879 on cpu 35:
percpu_counter_add_batch+0x83/0xd0
percpu_counter_add_batch at lib/percpu_counter.c:91
__vm_enough_memory+0xb9/0x260
dup_mm+0x3a4/0x8f0
copy_process+0x2458/0x3240
_do_fork+0xaa/0x9f0
__do_sys_clone+0x125/0x160
__x64_sys_clone+0x70/0x90
do_syscall_64+0x91/0xb05
entry_SYSCALL_64_after_hwframe+0x49/0xbe
read to 0xffffffff9451c538 of 8 bytes by task 66773 on cpu 19:
__vm_enough_memory+0x199/0x260
percpu_counter_read_positive at include/linux/percpu_counter.h:81
(inlined by) __vm_enough_memory at mm/util.c:839
mmap_region+0x1b2/0xa10
do_mmap+0x45c/0x700
vm_mmap_pgoff+0xc0/0x130
ksys_mmap_pgoff+0x6e/0x300
__x64_sys_mmap+0x33/0x40
do_syscall_64+0x91/0xb05
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The read is outside percpu_counter::lock critical section which results in
a data race. Fix it by adding a READ_ONCE() in
percpu_counter_read_positive() which could also service as the existing
compiler memory barrier.
Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Marco Elver <elver@google.com> Link: http://lkml.kernel.org/r/1582302724-2804-1-git-send-email-cai@lca.pw Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Under some circumstances we may encounter a filesystem error on a
read-only block device, and if we try to save the error info to the
superblock and commit it, we'll wind up with a noisy error and
backtrace, i.e.:
[ 3337.146838] EXT4-fs error (device pmem1p2): ext4_get_journal_inode:4634: comm mount: inode #0: comm mount: iget: illegal inode #
------------[ cut here ]------------
generic_make_request: Trying to write to read-only block-device pmem1p2 (partno 2)
WARNING: CPU: 107 PID: 115347 at block/blk-core.c:788 generic_make_request_checks+0x6b4/0x7d0
...
To avoid this, commit the error info in the superblock only if the
block device is writable.
machine_device_initcall expands to __define_machine_initcall, which in
turn has the macro machine_is used in it, which declares mach_##name
with an __attribute__((weak)). define_machine actually defines
mach_##name, which in this file happens before the declaration, hence
the warning.
To fix this, move define_machine after machine_device_initcall so that
the declaration occurs before the definition, which matches how
machine_device_initcall and define_machine work throughout
arch/powerpc.
While we're here, remove some spaces before tabs.
Fixes: 8f101a051ef0 ("edac: cpc925 MC platform device setup") Reported-by: Nick Desaulniers <ndesaulniers@google.com> Suggested-by: Ilie Halip <ilie.halip@gmail.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200323222729.15365-1-natechancellor@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When dreq is allocated by nfs_direct_req_alloc(), dreq->kref is
initialized to 2. Therefore we need to call nfs_direct_req_release()
twice to release the allocated dreq. Usually it is called in
nfs_file_direct_{read, write}() and nfs_direct_complete().
However, current code only calls nfs_direct_req_relese() once if
nfs_get_lock_context() fails in nfs_file_direct_{read, write}().
So, that case would result in memory leak.
The driver fails to probe with -EPROBE_DEFER if battery's power supply
(charger driver) isn't ready yet and this results in a bit noisy error
message in KMSG during kernel's boot up. Let's silence the harmless
error message.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Reviewed-by: Andrew F. Davis <afd@ti.com> Reviewed-by: Pali Rohár <pali@kernel.org> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
clk_hw_round_rate() may call round rate function of its parents. In case
of SAM9X60 two of USB parrents are PLLA and UPLL. These clocks are
controlled by clk-sam9x60-pll.c driver. The round rate function for this
driver is sam9x60_pll_round_rate() which call in turn
sam9x60_pll_get_best_div_mul(). In case the requested rate is not in the
proper range (rate < characteristics->output[0].min &&
rate > characteristics->output[0].max) the sam9x60_pll_round_rate() will
return a negative number to its caller (called by
clk_core_round_rate_nolock()). clk_hw_round_rate() will return zero in
case a negative number is returned by clk_core_round_rate_nolock(). With
this, the USB clock will continue its rate computation even caller of
clk_hw_round_rate() returned an error. With this, the USB clock on SAM9X60
may not chose the best parent. I detected this after a suspend/resume
cycle on SAM9X60.
kmemleak reports several memory leaks from devicetree unittest.
This is the fix for problem 2 of 5.
of_unittest_platform_populate() left an elevated reference count for
grandchild nodes (which are platform devices). Fix the platform
device reference counts so that the memory will be freed.
Fixes: fb2caa50fbac ("of/selftest: add testcase for nodes with same name and address") Reported-by: Erhard F. <erhard_f@mailbox.org> Signed-off-by: Frank Rowand <frank.rowand@sony.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without including psci.h and arm-smccc.h, we now get a build failure in
some configurations:
arch/arm64/kernel/cpu_errata.c: In function 'arm64_update_smccc_conduit':
arch/arm64/kernel/cpu_errata.c:278:10: error: 'psci_ops' undeclared (first use in this function); did you mean 'sysfs_ops'?
arch/arm64/kernel/cpu_errata.c: In function 'arm64_set_ssbd_mitigation':
arch/arm64/kernel/cpu_errata.c:311:3: error: implicit declaration of function 'arm_smccc_1_1_hvc' [-Werror=implicit-function-declaration]
arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_2, state, NULL);
The ref counting is broken for OF_DYNAMIC when sysfs is disabled because
the kobject initialization is skipped. Only the properties
add/remove/update should be skipped for !SYSFS config.
Tested-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Frank Rowand <frowand.list@gmail.com> Acked-by: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Endianness can vary in the system, add le32_to_cpu when comparing
partition sizes from smem.
Signed-off-by: Chris Lew <clew@codeaurora.org> Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current length check:
sizeof(cmd) + len > r->entry_size
will allow very large values of len (> U16_MAX - sizeof(cmd))
and can cause a buffer overflow. Fix the check to cover this case.
In addition, ensure the mailbox entry_size is not too small,
since this can also bypass the above check.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com> Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wil_err inside wil_rx_refill can flood the log buffer.
Replace it with wil_err_ratelimited.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION is only applicable for QCOM UFS host
controller version 2.x.y and this has been fixed from version 3.x.y
onwards, hence this change removes this quirk for version 3.x.y onwards.
[mkp: applied by hand]
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Asutosh Das <asutoshd@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As multiple requests are submitted to the ufs host controller in
parallel there could be instances where the command completion interrupt
arrives later for a request that is already processed earlier as the
corresponding doorbell was cleared when handling the previous
interrupt. Read the interrupt status in a loop after processing the
received interrupt to catch such interrupts and handle it.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org> Signed-off-by: Asutosh Das <asutoshd@codeaurora.org> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For negative temperatures, "temp" debugfs is showing wrong values.
Use signed types so proper calculations is done for sub zero
temperatures.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firmware ready event may take longer than
current timeout in some scenarios, for example
with multiple RFs connected where each
requires an initial calibration.
Increase the timeout to support these scenarios.
Signed-off-by: Hamad Kadmany <hkadmany@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We cannot blindly query the direction of all GPIOs when the pins are
first registered. The get_direction callback normally triggers a
read/write to hardware, but we shouldn't be touching the hardware for
an individual GPIO until after it's been properly claimed.
Signed-off-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Parfait (version 2.1.0) static code analysis tool found the
following NULL pointer derefernce problem.
- drivers/gpu/drm/drm_dp_mst_topology.c
The call to drm_dp_calculate_rad() in function drm_dp_port_setup_pdt()
could result in a NULL pointer being returned to port->mstb due to a
failure to allocate memory for port->mstb.
Signed-off-by: Joe Moriarty <joe.moriarty@oracle.com> Reviewed-by: Steven Sistare <steven.sistare@oracle.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20180212195144.98323-3-joe.moriarty@oracle.com Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the error path of the firmware loading error, the driver tries to
release the card object and set NULL to drvdata. This may be referred
badly at the possible PM action, as the driver itself is still bound
and the PM callbacks read the card object.
Instead, we continue the probing as if it were no option set. This is
often a better choice than the forced abort, too.
If the dxfer_len is greater than 256M then the request is invalid and we
need to call sg_remove_request in sg_common_write.
Link: https://lore.kernel.org/r/1586777361-17339-1-git-send-email-huawei.libin@huawei.com Fixes: f930c7043663 ("scsi: sg: only check for dxfer_len greater than 256M") Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Li Bin <huawei.libin@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Traced event can trigger 'snapshot' operation(i.e. calls snapshot_trigger()
or snapshot_count_trigger()) when register_snapshot_trigger() has completed
registration but doesn't allocate buffer for 'snapshot' event trigger. In
the rare case, 'snapshot' operation always detects the lack of allocated
buffer so make register_snapshot_trigger() allocate buffer first.
A number of hangs have been reported against the target driver; they are
due to the fact that multiple threads may try to destroy the iscsi session
at the same time. This may be reproduced for example when a "targetcli
iscsi/iqn.../tpg1 disable" command is executed while a logout operation is
underway.
When this happens, two or more threads may end up sleeping and waiting for
iscsit_close_connection() to execute "complete(session_wait_comp)". Only
one of the threads will wake up and proceed to destroy the session
structure, the remaining threads will hang forever.
Note that if the blocked threads are somehow forced to wake up with
complete_all(), they will try to free the same iscsi session structure
destroyed by the first thread, causing double frees, memory corruptions
etc...
With this patch, the threads that want to destroy the iscsi session will
increase the session refcount and will set the "session_close" flag to 1;
then they wait for the driver to close the remaining active connections.
When the last connection is closed, iscsit_close_connection() will wake up
all the threads and will wait for the session's refcount to reach zero;
when this happens, iscsit_close_connection() will destroy the session
structure because no one is referencing it anymore.
INFO: task targetcli:5971 blocked for more than 120 seconds.
Tainted: P OE 4.15.0-72-generic #81~16.04.1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
targetcli D 0 5971 1 0x00000080
Call Trace:
__schedule+0x3d6/0x8b0
? vprintk_func+0x44/0xe0
schedule+0x36/0x80
schedule_timeout+0x1db/0x370
? __dynamic_pr_debug+0x8a/0xb0
wait_for_completion+0xb4/0x140
? wake_up_q+0x70/0x70
iscsit_free_session+0x13d/0x1a0 [iscsi_target_mod]
iscsit_release_sessions_for_tpg+0x16b/0x1e0 [iscsi_target_mod]
iscsit_tpg_disable_portal_group+0xca/0x1c0 [iscsi_target_mod]
lio_target_tpg_enable_store+0x66/0xe0 [iscsi_target_mod]
configfs_write_file+0xb9/0x120
__vfs_write+0x1b/0x40
vfs_write+0xb8/0x1b0
SyS_write+0x5c/0xe0
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
Link: https://lore.kernel.org/r/20200313170656.9716-3-mlombard@redhat.com Reported-by: Matt Coleman <mcoleman@datto.com> Tested-by: Matt Coleman <mcoleman@datto.com> Tested-by: Rahul Kundu <rahul.kundu@chelsio.com> Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The host reports support for the synthetic feature X86_FEATURE_SSBD
when any of the three following hardware features are set:
CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31]
CPUID.80000008H:EBX.AMD_SSBD[bit 24]
CPUID.80000008H:EBX.VIRT_SSBD[bit 25]
Either of the first two hardware features implies the existence of the
IA32_SPEC_CTRL MSR, but CPUID.80000008H:EBX.VIRT_SSBD[bit 25] does
not. Therefore, CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31] should only be
set in the guest if CPUID.(EAX=7,ECX=0):EDX.SSBD[bit 31] or
CPUID.80000008H:EBX.AMD_SSBD[bit 24] is set on the host.
Fixes: 0c54914d0c52a ("KVM: x86: use Intel speculation bugs and features as derived in generic x86 code") Signed-off-by: Jim Mattson <jmattson@google.com> Reviewed-by: Jacob Xu <jacobhxu@google.com> Reviewed-by: Peter Shier <pshier@google.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Reported-by: Eric Biggers <ebiggers@kernel.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 4.x: adjust indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
We do not want to create initialized extents beyond end of file because
for e2fsck it is impossible to distinguish them from a case of corrupted
file size / extent tree and so it complains like:
Inode 12, i_size is 147456, should be 163840. Fix? no
Code in ext4_ext_convert_to_initialized() and
ext4_split_convert_extents() try to make sure it does not create
initialized extents beyond inode size however they check against
inode->i_size which is wrong. They should instead check against
EXT4_I(inode)->i_disksize which is the current inode size on disk.
That's what e2fsck is going to see in case of crash before all dirty
data is written. This bug manifests as generic/456 test failure (with
recent enough fstests where fsx got fixed to properly pass
FALLOC_KEEP_SIZE_FL flags to the kernel) when run with dioread_lock
mount option.
CC: stable@vger.kernel.org Fixes: 21ca087a3891 ("ext4: Do not zero out uninitialized extents beyond i_size") Reviewed-by: Lukas Czerner <lczerner@redhat.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Link: https://lore.kernel.org/r/20200331105016.8674-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously we would set the reloc root's last snapshot to transid - 1.
However there was a problem with doing this, and we changed it to
setting the last snapshot to the generation of the commit node of the fs
root.
This however broke should_ignore_root(). The assumption is that if we
are in a generation newer than when the reloc root was created, then we
would find the reloc root through normal backref lookups, and thus can
ignore any fs roots we find with an old enough reloc root.
Now that the last snapshot could be considerably further in the past
than before, we'd end up incorrectly ignoring an fs root. Thus we'd
find no nodes for the bytenr we were searching for, and we'd fail to
relocate anything. We'd loop through the relocate code again and see
that there were still used space in that block group, attempt to
relocate those bytenr's again, fail in the same way, and just loop like
this forever. This is tricky in that we have to not modify the fs root
at all during this time, so we need to have a block group that has data
in this fs root that is not shared by any other root, which is why this
has been difficult to reproduce.
Fixes: 054570a1dc94 ("Btrfs: fix relocation incorrectly dropping data references") CC: stable@vger.kernel.org # 4.9+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mapping table may contain also ignore_ctl_error flag for devices
that are known to behave wild. Since this flag always writes the
card's own ignore_ctl_error flag, it overrides the value already set
by the module option, so it doesn't follow user's expectation.
Let's fix the code not to clear the flag that has been set by user.
Currently function sst_platform_get_resources always returns zero and
error return codes set by the function are never returned. Fix this
by returning the error return code in variable ret rather than the
hard coded zero.
Addresses-Coverity: ("Unused value") Fixes: f533a035e4da ("ASoC: Intel: mrfld - create separate module for pci part") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Cezary Rojewski <cezary.rojewski@intel.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20200208220720.36657-1-colin.king@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check on p->sink looks bogus, I believe it should be p->source
since the following code blocks are related to p->source. Fix
this by replacing p->sink with p->source.
Fixes: 24c8d14192cc ("ASoC: Intel: mrfld: add DSP core controls") Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Copy-paste error") Link: https://lore.kernel.org/r/20191119113640.166940-1-colin.king@canonical.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ext4_fill_super detects an invalid number of inodes per group, the
resulting error message printed the number of blocks per group, rather
than the number of inodes per group. Fix it to print the correct value.
ext4_fill_super doublechecks the number of groups before mounting; if
that check fails, the resulting error message prints the group count
from the ext4_sb_info sbi, which hasn't been set yet. Print the freshly
computed group count instead (which at that point has just been computed
in "blocks_count").
Improve comments in jbd2_journal_commit_transaction() to describe why
we don't need to clear the buffer_mapped bit for freeing file mapping
buffers whose page mapping is NULL.
Link: https://lore.kernel.org/r/20200217112706.20085-1-yi.zhang@huawei.com Fixes: c96dceeabf76 ("jbd2: do not clear the BH_Mapped flag when forgetting a metadata buffer") Suggested-by: Jan Kara <jack@suse.cz> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: zhangyi (F) <yi.zhang@huawei.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The async version of ufshcd_hold(async == true), which is only called in
queuecommand path as for now, is expected to work in atomic context, thus
it should not sleep or schedule out. When it runs into the condition that
clocks are ON but link is still in hibern8 state, it should bail out
without flushing the clock ungate work.
Fixes: f2a785ac2312 ("scsi: ufshcd: Fix race between clk scaling and ungate work") Link: https://lore.kernel.org/r/1581392451-28743-6-git-send-email-cang@codeaurora.org Reviewed-by: Hongwu Su <hongwus@codeaurora.org> Reviewed-by: Asutosh Das <asutoshd@codeaurora.org> Reviewed-by: Bean Huo <beanhuo@micron.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The behaviour for what is considered an anycast address changed in
commit 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after
encountering pmtu exception"). This now considers the first
address in a subnet where there is a route via a gateway
to be an anycast address.
This breaks path MTU discovery and traceroutes when a host in a
remote network uses the address at the start of a prefix
(eg 2600:: advertised as 2600::/48 in the DFZ) as ICMP errors
will not be sent to anycast addresses.
This patch excludes any routes with a gateway, or via point to
point links, like the behaviour previously from
rt6_is_gw_or_nonexthop in net/ipv6/route.c.
This can be tested with:
ip link add v1 type veth peer name v2
ip netns add test
ip netns exec test ip link set lo up
ip link set v2 netns test
ip link set v1 up
ip netns exec test ip link set v2 up
ip addr add 2001:db8::1/64 dev v1 nodad
ip addr add 2001:db8:100:: dev lo nodad
ip netns exec test ip addr add 2001:db8::2/64 dev v2 nodad
ip netns exec test ip route add unreachable 2001:db8:1::1
ip netns exec test ip route add 2001:db8:100::/64 via 2001:db8::1
ip netns exec test sysctl net.ipv6.conf.all.forwarding=1
ip route add 2001:db8:1::1 via 2001:db8::2
ping -I 2001:db8::1 2001:db8:1::1 -c1
ping -I 2001:db8:100:: 2001:db8:1::1 -c1
ip addr delete 2001:db8:100:: dev lo
ip netns delete test
Currently the first ping will get back a destination unreachable ICMP
error, but the second will never get a response, with "icmp6_send:
acast source" logged. After this patch, both get destination
unreachable ICMP replies.
Fixes: 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu exception") Signed-off-by: Tim Stallard <code@timstallard.me.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the local node id(qrtr_local_nid) is not modified after its
initialization, it equals to the broadcast node id(QRTR_NODE_BCAST).
So the messages from local node should not be taken as broadcast
and keep the process going to send them out anyway.
The definitions are as follow:
static unsigned int qrtr_local_nid = NUMA_NO_NODE;
Fixes: fdf5fd397566 ("net: qrtr: Broadcast messages only from control port") Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_IP_MULTICAST is not set and multicast ip is added to the device
with autojoin flag or when multicast ip is deleted kernel will crash.
steps to reproduce:
ip addr add 224.0.0.0/32 dev eth0
ip addr del 224.0.0.0/32 dev eth0
or
ip addr add 224.0.0.0/32 dev eth0 autojoin
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
pc : _raw_write_lock_irqsave+0x1e0/0x2ac
lr : lock_sock_nested+0x1c/0x60
Call trace:
_raw_write_lock_irqsave+0x1e0/0x2ac
lock_sock_nested+0x1c/0x60
ip_mc_config.isra.28+0x50/0xe0
inet_rtm_deladdr+0x1a8/0x1f0
rtnetlink_rcv_msg+0x120/0x350
netlink_rcv_skb+0x58/0x120
rtnetlink_rcv+0x14/0x20
netlink_unicast+0x1b8/0x270
netlink_sendmsg+0x1a0/0x3b0
____sys_sendmsg+0x248/0x290
___sys_sendmsg+0x80/0xc0
__sys_sendmsg+0x68/0xc0
__arm64_sys_sendmsg+0x20/0x30
el0_svc_common.constprop.2+0x88/0x150
do_el0_svc+0x20/0x80
el0_sync_handler+0x118/0x190
el0_sync+0x140/0x180
Fixes: 93a714d6b53d ("multicast: Extend ip address command to enable multicast group join/leave on") Signed-off-by: Taras Chornyi <taras.chornyi@plvision.eu> Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current hsr code, only 0 and 1 protocol versions are valid.
But current hsr code doesn't check the version, which is received by
userspace.
Test commands:
ip link add dummy0 type dummy
ip link add dummy1 type dummy
ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 version 4
In the test commands, version 4 is invalid.
So, the command should be failed.
After this patch, following error will occur.
"Error: hsr: Only versions 0..1 are supported."
Fixes: ee1c27977284 ("net/hsr: Added support for HSR v1") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the commit 2b8bd606b1e6 ("mfd: dln2: More sanity checking for endpoints")
tries to harden the sanity checks it made at the same time a regression,
i.e. mixed in and out endpoints. Obviously it should have been not tested on
real hardware at that time, but unluckily it didn't happen.
So, fix above mentioned typo and make device being enumerated again.
While here, introduce an enumerator for magic values to prevent similar issue
to happen in the future.
Fixes: 2b8bd606b1e6 ("mfd: dln2: More sanity checking for endpoints") Cc: Oliver Neukum <oneukum@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/misc/echo/echo.c:384:27: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((ec->nonupdate_dwell == 0)) {
~~~~~~~~~~~~~~~~~~~~^~~~
drivers/misc/echo/echo.c:384:27: note: remove extraneous parentheses
around the comparison to silence this warning
if ((ec->nonupdate_dwell == 0)) {
~ ^ ~
drivers/misc/echo/echo.c:384:27: note: use '=' to turn this equality
comparison into an assignment
if ((ec->nonupdate_dwell == 0)) {
^~
=
1 warning generated.
Remove them and while we're at it, simplify the zero check as '!var' is
used more than 'var == 0'.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the current implementation, the call to loadcam_multi() is wrapped
between switch_to_as1() and restore_to_as0() calls so, when it tries
to create its own temporary AS=1 TLB1 entry, it ends up duplicating
the existing one created by switch_to_as1(). Add a check to skip
creating the temporary entry if already running in AS=1.
Fixes: d9e1831a4202 ("powerpc/85xx: Load all early TLB entries at once") Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com> Acked-by: Scott Wood <oss@buserror.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20200123111914.2565-1-laurentiu.tudor@nxp.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The wait_event() function is used to detect command completion.
When send_guid_cmd() returns an error, smi_send() has not been
called to send data. Therefore, wait_event() should not be used
on the error path, otherwise it will cause the following warning:
drm_pci_alloc/drm_pci_free are very thin wrappers around the core dma
facilities, and we have no special reason within the drm layer to behave
differently. In particular, since
commit 64e62bdf04ab ("drm/dp_mst: Remove VCPI while disabling topology
mgr")
Prompted me to take a closer look at how we clear the payload state in
general when disabling the topology, and it turns out there's actually
two subtle issues here.
The first is that we're not grabbing &mgr.payload_lock when clearing the
payloads in drm_dp_mst_topology_mgr_set_mst(). Seeing as the canonical
lock order is &mgr.payload_lock -> &mgr.lock (because we always want
&mgr.lock to be the inner-most lock so topology validation always
works), this makes perfect sense. It also means that -technically- there
could be racing between someone calling
drm_dp_mst_topology_mgr_set_mst() to disable the topology, along with a
modeset occurring that's modifying the payload state at the same time.
The second is the more obvious issue that Wayne Lin discovered, that
we're not clearing proposed_payloads when disabling the topology.
I actually can't see any obvious places where the racing caused by the
first issue would break something, and it could be that some of our
higher-level locks already prevent this by happenstance, but better safe
then sorry. So, let's make it so that drm_dp_mst_topology_mgr_set_mst()
first grabs &mgr.payload_lock followed by &mgr.lock so that we never
race when modifying the payload state. Then, we also clear
proposed_payloads to fix the original issue of enabling a new topology
with a dirty payload state. This doesn't clear any of the drm_dp_vcpi
structures, but those are getting destroyed along with the ports anyway.
Changes since v1:
* Use sizeof(mgr->payloads[0])/sizeof(mgr->proposed_vcpis[0]) instead -
vsyrjala
Cc: Sean Paul <sean@poorly.run> Cc: Wayne Lin <Wayne.Lin@amd.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200122194321.14953-1-lyude@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
