Fix open error handling which failed to detect errors when reading the
MSR and LSR registers, something which could lead to the shadow
registers being initialised from errnos.
Note that calling the generic close implementation is sufficient in the
error paths as the interrupt urb has not yet been submitted and the
register updates have not been made.
Fixes: f4c1e8d597d1 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to detect short control-message transfers rather than continue
with zero-initialised data when retrieving modem status and during
device initialisation.
Fixes: 52af95459939 ("USB: add USB serial ssu100 driver") Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.
Acked-by: Peter Chen <peter.chen@nxp.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com> Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect") Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.
Acked-by: Peter Chen <peter.chen@nxp.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com> Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect") Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9b6 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning from for_each_available_child_of_node() loop requires cleaning
up node refcount. Error paths lacked it so for example in case of
deferred probe, the refcount of phy node was left increased.
Fixes: 6d40500ac9b6 ("usb: ehci/ohci-exynos: Fix of_node_put() for child when getting PHYs") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
L2 was running with uninitialized PML fields which led to incomplete
dirty bitmap logging. This manifested as all kinds of subtle erratic
behavior of the nested guest.
Fix to the exception table entry check by using probed address
instead of the address of copied instruction.
This bug may cause unexpected kernel panic if user probe an address
where an exception can happen which should be fixup by __ex_table
(e.g. copy_from_user.)
Unless user puts a kprobe on such address, this doesn't
cause any problem.
This bug has been introduced years ago, by commit:
464846888d9a ("x86/kprobes: Fix a bug which can modify kernel code permanently").
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 464846888d9a ("x86/kprobes: Fix a bug which can modify kernel code permanently") Link: http://lkml.kernel.org/r/148829899399.28855.12581062400757221722.stgit@devbox Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8fd524b355da ("x86: Kill bad_dma_address variable") has killed
bad_dma_address variable and used instead of macro DMA_ERROR_CODE
which is always zero. Since dma_addr is unsigned, the statement
dma_addr >= DMA_ERROR_CODE
is always true, and not needed.
arch/x86/kernel/pci-calgary_64.c: In function ‘iommu_free’:
arch/x86/kernel/pci-calgary_64.c:299:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
if (unlikely((dma_addr >= DMA_ERROR_CODE) && (dma_addr < badend))) {
Fixes: 8fd524b355da ("x86: Kill bad_dma_address variable") Signed-off-by: Nikola Pajkovsky <npajkovsky@suse.cz> Cc: iommu@lists.linux-foundation.org Cc: Jon Mason <jdmason@kudzu.us> Cc: Muli Ben-Yehuda <mulix@mulix.org> Link: http://lkml.kernel.org/r/7612c0f9dd7c1290407dbf8e809def922006920b.1479161177.git.npajkovsky@suse.cz Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d87a ("mwifiex: add key material v2 support") Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit fcd2042e8d36 ("mwifiex: printk() overflow with 32-byte
SSIDs"), we failed to account for the existence of 32-char SSIDs in our
debugfs code. Unlike in that case though, we zeroed out the containing
struct first, and I'm pretty sure we're guaranteed to have some padding
after the 'ssid.ssid' and 'ssid.ssid_len' fields (the struct is 33 bytes
long).
gcc gets confused about the control flow in ktd2692_parse_dt(), causing
it to warn about what seems like a potential bug:
drivers/leds/leds-ktd2692.c: In function 'ktd2692_probe':
drivers/leds/leds-ktd2692.c:244:15: error: '*((void *)&led_cfg+8)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:225:7: error: 'led_cfg.flash_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:232:3: error: 'led_cfg.movie_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is fine, and slightly reworking it in an equivalent way lets
gcc figure that out too, which gets rid of the warning.
Reading both fault and status registers and logging any fault should
take priority over handling status register update.
Fix by moving the status handling to later in interrupt routine.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Caching the fault register after a single I2C read may not keep an accurate
value.
Fix by doing two reads in irq_handle_thread() and using the cached value
elsewhere. If a safety timer fault later clears itself, we apparently don't get
an interrupt (INT), however other interrupts would refresh the register cache.
From the data sheet: "When a fault occurs, the charger device sends out INT
and keeps the fault state in REG09 until the host reads the fault register.
Before the host reads REG09 and all the faults are cleared, the charger
device would not send any INT upon new faults. In order to read the
current fault status, the host has to read REG09 two times consecutively.
The 1st reads fault register status from the last read [1] and the 2nd reads
the current fault register status."
[1] presumably a typo; should be "last fault"
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We wrongly get uevents for bq24190-charger and bq24190-battery on every
register change.
Fix by checking the association with charger and battery before
emitting uevent(s).
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device specific data is not fully initialized on
request_threaded_irq(). This may cause a crash when the IRQ handler
tries to reference them.
Fix the issue by installing IRQ handler at the end of the probe.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_resume() does a register_reset() which clears charger host mode.
Fix by calling set_mode_host() after the reset.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interrupt signal is TRIGGER_FALLING. This is is specified in the
data sheet PIN FUNCTIONS: "The INT pin sends active low, 256us
pulse to host to report charger device status and fault."
Also the direction can be seen in the data sheet Figure 37 "BQ24190
with D+/D- Detection and USB On-The-Go (OTG)" which shows a 10k
pull-up resistor installed for the sample configurations.
Fixes: d7bf353fd0aa3 ("bq24190_charger: Add support for TI BQ24190 Battery Charger") Signed-off-by: Liam Breck <kernel@networkimprov.net> Acked-by: Mark Greer <mgreer@animalcreek.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because we incorrectly load the opcode into r0 before calling
__trace_opal_exit(), whereas it expects the opcode in r3 (first function
parameter). In fact we are leaving the retval in r3, so opcode and
retval will always show the same value.
The switch that conditionally sets CPUPOWER_CAP_HAS_TURBO_RATIO and
CPUPOWER_CAP_IS_SNB flags is missing a break, so all cores get both
flags set and an assumed base clock of 100 MHz for turbo values.
Reported-by: GSR <gsr.bugs@infernal-iceberg.com> Tested-by: GSR <gsr.bugs@infernal-iceberg.com>
References: https://bugs.debian.org/859978 Fixes: 8fb2e440b223 (cpupower: Show Intel turbo ratio support via ...) Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PJ4 inline asm sequence to write to cp15 cannot be built in Thumb-2
mode, due to the way it performs arithmetic on the program counter, so it
is built in ARM mode instead. However, building C files in ARM mode under
CONFIG_THUMB2_KERNEL is problematic, since the instrumentation performed
by subsystems like ftrace does not expect having to deal with interworking
branches.
Since the sequence in question is simply a poor man's ISB instruction,
let's use a straight 'isb' instead when building in Thumb2 mode. Thumb2
implies V7, so 'isb' should always be supported in that case.
Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
posix_acl_update_mode() could possibly clear 'acl', if so we leak the
memory pointed by 'acl'. Save this pointer before calling
posix_acl_update_mode() and release the memory if 'acl' really gets
cleared.
Link: http://lkml.kernel.org/r/1486678332-2430-1-git-send-email-xiyou.wangcong@gmail.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reported-by: Mark Salyzyn <salyzyn@android.com> Reviewed-by: Jan Kara <jack@suse.cz> Reviewed-by: Greg Kurz <groug@kaod.org> Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Ron Minnich <rminnich@sandia.gov> Cc: Latchesar Ionkov <lucho@ionkov.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling a dm ioctl that doesn't process any data
(IOCTL_FLAGS_NO_PARAMS), the contents of the data field in struct
dm_ioctl are left initialized. Current code is incorrectly extending
the size of data copied back to user, causing the contents of kernel
stack to be leaked to user. Fix by only copying contents before data
and allow the functions processing the ioctl to override.
Signed-off-by: Adrian Salido <salidoa@google.com> Reviewed-by: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NFSv2/v3 code does not systematically check whether we decode past
the end of the buffer. This generally appears to be harmless, but there
are a few places where we do arithmetic on the pointers involved and
don't account for the possibility that a length could be negative. Add
checks to catch these.
Reported-by: Tuomas Haanpää <thaan@synopsys.com> Reported-by: Ari Kauppi <ari@synopsys.com> Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Al pointed, d_revalidate should return RCU lookup before using d_inode.
This was originally introduced by:
commit 34286d666230 ("fs: rcu-walk aware d_revalidate method").
Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Cc: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids potential problems caused by a race where the inode gets
renamed out from its parent directory and the parent directory is
deleted while ext4_d_revalidate() is running.
Fixes: 28b4c263961c Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...otherwise an user can enable encryption for certain files even
when the filesystem is unable to support it.
Such a case would be a filesystem created by mkfs.ext4's default
settings, 1KiB block size. Ext4 supports encyption only when block size
is equal to PAGE_SIZE.
But this constraint is only checked when the encryption feature flag
is set.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnd Bergmann [Thu, 4 May 2017 20:52:03 +0000 (22:52 +0200)]
IB/ehca: fix maybe-uninitialized warnings
The driver causes two warnings about possibly uninitialized variables:
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1908:4: warning: 'prev_pgaddr' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/infiniband/hw/ehca/ehca_mrmw.c:1924:14: note: 'prev_pgaddr' was declared here
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_reg_mr':
drivers/infiniband/hw/ehca/ehca_mrmw.c:2430:5: warning: 'hret' may be used uninitialized in this function [-Wmaybe-uninitialized]
The first one is definitely a false positive, the second one may or may not
be one. In both cases, adding an intialization is the safe and easy
workaround.
The driver was removed in mainline in commit e581d111dad3
("staging/rdma: remove deprecated ehca driver"), in linux-4.6.
In 4.4, the file is located in drivers/staging/rdma/ehca/ehca_mrmw.c,
and the fix still applies.
This is fixed upstream in commit 898fa52b4ac3 ("IB/qib: Remove qpn, qp tables and
related variables from qib"), which does a lot of other things as well.
Instead, I just backport the rename of the local BITS_PER_PAGE definition to
RVT_BITS_PER_PAGE.
The driver first showed up in linux-2.6.35, and the fixup should still apply
to that. The upstream fix went into v4.6, so we could apply this workaround
to both 3.18 and 4.4.
Fixes: f931551bafe1 ("IB/qib: Add new qib driver for QLogic PCIe InfiniBand adapters") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ross Lagerwall [Wed, 3 May 2017 08:44:19 +0000 (09:44 +0100)]
netlink: Allow direct reclaim for fallback allocation
The backport of d35c99ff77ec ("netlink: do not enter direct reclaim from
netlink_dump()") to the 4.4 branch (first in 4.4.32) mistakenly removed
direct claim from the initial large allocation _and_ the fallback
allocation which means that allocations can spuriously fail.
Fix the issue by adding back the direct reclaim flag to the fallback
allocation.
Fixes: 6d123f1d396b ("netlink: do not enter direct reclaim from netlink_dump()") Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f209fa03fc9d ("serial: 8250_pci: Detach low-level driver during
PCI error recovery") introduces a potential use-after-free in case the
pciserial_init_ports call in serial8250_io_resume fails, which may
happen if a memory allocation fails or if the .init quirk failed for
whatever reason). If this happen, further pci_get_drvdata will return a
pointer to freed memory.
This patch reworks the PCI recovery resume hook to restore the old priv
structure in this case, which should be ok, since the ports were already
detached. Such error during recovery causes us to give up on the
recovery.
Fixes: f209fa03fc9d ("serial: 8250_pci: Detach low-level driver during PCI error recovery") Reported-by: Michal Suchanek <msuchanek@suse.com> Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an EEH occurs during device initialization, the port timeout logic
can cause excessive delays as MMIO reads will fail. Depending on where
they are experienced, these delays can lead to a prolonged reset,
causing an unnecessary triggering of other timeout logic in the SCSI
stack or user applications.
To expedite recovery, the port timeout logic is updated to decay the
timeout at a much faster rate when in the presence of a likely EEH
frozen event.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EEH reset handler is ignorant to the current state of the driver
when processing a frozen event and initiating a device reset. This can
be an issue if an EEH event occurs while a user or stack initiated reset
is executing. More specifically, if an EEH occurs while the SCSI host
reset handler is active, the reset initiated by the EEH thread will
likely collide with the host reset thread. This can leave the device in
an inconsistent state, or worse, cause a system crash.
As a remedy, the EEH handler is updated to evaluate the device state and
take appropriate action (proceed, wait, or disconnect host). The host
reset handler is also updated to handle situations where an EEH occurred
during a host reset. In such situations, the host reset handler will
delay reporting back a success to give the EEH reset an opportunity to
complete.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Acked-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a port link is established, the AFU sends a 'link up' interrupt.
After the link is up, corresponding initialization steps are performed
on the card. Following that, when the card is ready for I/O, the AFU
sends 'login succeeded' interrupt. Today, cxlflash invokes
scsi_scan_host() upon receipt of both interrupts.
SCSI commands sent to the port prior to the 'login succeeded' interrupt
will fail with 'port not available' error. This is not desirable.
Moreover, when async_scan is active for the host, subsequent scan calls
are terminated with error. Due to this, the scsi_scan_host() call
performed after 'login succeeded' interrupt could portentially return
error and the devices may not be scanned properly.
To avoid this problem, scsi_scan_host() should be called only after the
'login succeeded' interrupt.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com> Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tg3_set_eeprom() function correctly initializes the 'start' variable,
but gcc generates a false warning:
drivers/net/ethernet/broadcom/tg3.c: In function 'tg3_set_eeprom':
drivers/net/ethernet/broadcom/tg3.c:12057:4: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
I have not come up with a way to restructure the code in a way that
avoids the warning without making it less readable, so this adds an
initialization for the declaration to shut up that warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When map_word gets too large, we use a lot of kernel stack, and for
MTD_MAP_BANK_WIDTH_32, this means we use more than the recommended
1024 bytes in a number of functions:
drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_write_buffers':
drivers/mtd/chips/cfi_cmdset_0020.c:651:1: warning: the frame size of 1336 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/mtd/chips/cfi_cmdset_0020.c: In function 'cfi_staa_erase_varsize':
drivers/mtd/chips/cfi_cmdset_0020.c:972:1: warning: the frame size of 1208 bytes is larger than 1024 bytes [-Wframe-larger-than=]
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'do_write_buffer':
drivers/mtd/chips/cfi_cmdset_0001.c:1835:1: warning: the frame size of 1240 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This can be avoided if all operations on the map word are done
indirectly and the stack gets reused between the calls. We can
mostly achieve this by selecting MTD_COMPLEX_MAPPINGS whenever
MTD_MAP_BANK_WIDTH_32 is set, but for the case that no other
bank width is enabled, we also need to use a non-constant
map_bankwidth() to convince the compiler to use less stack.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Brian: this patch mostly achieves its goal by forcing
MTD_COMPLEX_MAPPINGS (and the accompanying indirection) for 256-bit
mappings; the rest of the change is mostly a wash, though it helps
reduce stack size slightly. If we really care about supporting
256-bit mappings though, we should consider rewriting some of this
code to avoid keeping and assigning so many 256-bit objects on the
stack.] Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The awacs sound driver produces a false-positive warning in ppc64_defconfig:
sound/ppc/awacs.c: In function 'snd_pmac_awacs_init':
include/sound/control.h:219:9: warning: 'master_vol' may be used uninitialized in this function [-Wmaybe-uninitialized]
I haven't come up with a good way to rewrite the code to avoid the
warning, so here is a bad one: I initialize the variable before
the conditionall initialization so gcc no longer has to worry about
it.
The FE setups of Intel SST bytcr_rt5640 and bytcr_rt5651 drivers carry
the ignore_suspend flag, and this prevents the suspend/resume working
properly while the stream is running, since SST core code has the
check of the running streams and returns -EBUSY. Drop these
superfluous flags for fixing the behavior.
Also, the bytcr_rt5640 driver lacks of nonatomic flag in some FE
definitions, which leads to the kernel Oops at suspend/resume like:
A signal can interrupt a SendReceive call which result in incoming
responses to the call being ignored. This is a problem for calls such as
open which results in the successful response being ignored. This
results in an open file resource on the server.
The patch looks into responses which were cancelled after being sent and
in case of successful open closes the open fids.
For this patch, the check is only done in SendReceive2()
The handling of the might_cancel queueing is not properly protected, so
parallel operations on the file descriptor can race with each other and
lead to list corruptions or use after free.
Protect the context for these operations with a seperate lock.
The wait queue lock cannot be reused for this because that would create a
lock inversion scenario vs. the cancel lock. Replacing might_cancel with an
atomic (atomic_t or atomic bit) does not help either because it still can
race vs. the actual list operation.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: "linux-fsdevel@vger.kernel.org" Cc: syzkaller <syzkaller@googlegroups.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: linux-fsdevel@vger.kernel.org Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1701311521430.3457@nanos Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On x86-32, with CONFIG_FIRMWARE and multiple CPUs, if you enable function
graph tracing and then suspend to RAM, it will triple fault and reboot when
it resumes.
The first fault happens when booting a secondary CPU:
The early head_32.S code calls into load_ucode_ap(), which has an an
ftrace hook, so it calls prepare_ftrace_return(), which calls
ftrace_graph_is_dead(), which tries to access the global
'kill_ftrace_graph' variable with a virtual address, causing a fault
because the CPU is still in real mode.
The fix is to add a check in prepare_ftrace_return() to make sure it's
running in protected mode before continuing. The check makes sure the
stack pointer is a virtual kernel address. It's a bit of a hack, but
it's not very intrusive and it works well enough.
For reference, here are a few other (more difficult) ways this could
have potentially been fixed:
- Move startup_32_smp()'s call to load_ucode_ap() down to *after* paging
is enabled. (No idea what that would break.)
- Track down load_ucode_ap()'s entire callee tree and mark all the
functions 'notrace'. (Probably not realistic.)
- Pause graph tracing in ftrace_suspend_notifier_call() or bringup_cpu()
or __cpu_up(), and ensure that the pause facility can be queried from
real mode.
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net> Cc: linux-acpi@vger.kernel.org Cc: Borislav Petkov <bp@alien8.de> Cc: Len Brown <lenb@kernel.org> Link: http://lkml.kernel.org/r/5c1272269a580660703ed2eccf44308e790c7a98.1492123841.git.jpoimboe@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A client can append random data to the end of an NFSv2 or NFSv3 RPC call
without our complaining; we'll just stop parsing at the end of the
expected data and ignore the rest.
Encoded arguments and replies are stored together in an array of pages,
and if a call is too large it could leave inadequate space for the
reply. This is normally OK because NFS RPC's typically have either
short arguments and long replies (like READ) or long arguments and short
replies (like WRITE). But a client that sends an incorrectly long reply
can violate those assumptions. This was observed to cause crashes.
Also, several operations increment rq_next_page in the decode routine
before checking the argument size, which can leave rq_next_page pointing
well past the end of the page array, causing trouble later in
svc_free_pages.
So, following a suggestion from Neil Brown, add a central check to
enforce our expectation that no NFSv2/v3 call has both a large call and
a large reply.
As followup we may also want to rewrite the encoding routines to check
more carefully that they aren't running off the end of the page array.
We may also consider rejecting calls that have any extra garbage
appended. That would be safer, and within our rights by spec, but given
the age of our server and the NFS protocol, and the fact that we've
never enforced this before, we may need to balance that against the
possibility of breaking some oddball client.
Reported-by: Tuomas Haanpää <thaan@synopsys.com> Reported-by: Ari Kauppi <ari@synopsys.com> Reviewed-by: NeilBrown <neilb@suse.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arch_check_elf contains a usage of current_cpu_data that will call
smp_processor_id() with preemption enabled and therefore triggers a
"BUG: using smp_processor_id() in preemptible" warning when an fpxx
executable is loaded.
As a follow-up to commit b244614a60ab ("MIPS: Avoid a BUG warning during
prctl(PR_SET_FP_MODE, ...)"), apply the same fix to arch_check_elf by
using raw_current_cpu_data instead. The rationale quoted from the previous
commit:
"It is assumed throughout the kernel that if any CPU has an FPU, then
all CPUs would have an FPU as well, so it is safe to perform the check
with preemption enabled - change the code to use raw_ variant of the
check to avoid the warning."
Fixes: 46490b572544 ("MIPS: kernel: elf: Improve the overall ABI and FPU mode checks") Signed-off-by: James Cowgill <James.Cowgill@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15951/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KGDB is a kernel debug stub and it can't be used to debug userland as it
can only safely access kernel memory.
On MIPS however KGDB has always got the register state of sleeping
processes from the userland register context at the beginning of the
kernel stack. This is meaningless for kernel threads (which never enter
userland), and for user threads it prevents the user seeing what it is
doing while in the kernel:
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) 0x0000000000000000 in ?? ()
2 Thread 1 (init) 0x000000007705c4b4 in ?? ()
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Get the register state instead from the (partial) kernel register
context stored in the task's thread_struct for resume() to restore. All
threads now correctly appear to be in context_switch():
(gdb) info threads
Id Target Id Frame
...
3 Thread 2 (kthreadd) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
2 Thread 1 (init) context_switch (rq=<optimized out>, cookie=..., next=<optimized out>, prev=0x0) at kernel/sched/core.c:2903
1 Thread -2 (shadowCPU0) 0xffffffff8012524c in arch_kgdb_breakpoint () at arch/mips/kernel/kgdb.c:201
Call clobbered registers which aren't saved and exception registers
(BadVAddr & Cause) which can't be easily determined without stack
unwinding are reported as 0. The PC is taken from the return address,
such that the state presented matches that found immediately after
returning from resume().
Fixes: 8854700115ec ("[MIPS] kgdb: add arch support for the kernel's kgdb core") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Jason Wessel <jason.wessel@windriver.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15829/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snd_use_lock_sync() (thus its implementation
snd_use_lock_sync_helper()) has the 5 seconds timeout to break out of
the sync loop. It was introduced from the beginning, just to be
"safer", in terms of avoiding the stupid bugs.
However, as Ben Hutchings suggested, this timeout rather introduces a
potential leak or use-after-free that was apparently fixed by the
commit 2d7d54002e39 ("ALSA: seq: Fix race during FIFO resize"):
for example, snd_seq_fifo_event_in() -> snd_seq_event_dup() ->
copy_from_user() could block for a long time, and snd_use_lock_sync()
goes timeout and still leaves the cell at releasing the pool.
For fixing such a problem, we remove the break by the timeout while
still keeping the warning.
An abstraction of asynchronous transaction for transmission of MIDI
messages was introduced in Linux v4.4. Each driver can utilize this
abstraction to transfer MIDI messages via fixed-length payload of
transaction to a certain unit address. Filling payload of the transaction
is done by callback. In this callback, each driver can return negative
error code, however current implementation assigns the return value to
unsigned variable.
This commit changes type of the variable to fix the bug.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr> Fixes: 585d7cba5e1f ("ALSA: firewire-lib: add helper functions for asynchronous transactions to transfer MIDI messages") Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In situations where an skb is paged, the transport header pointer and
tail pointer can be the same because the skb contents are in frags.
This results in ioctl(SIOCINQ/FIONREAD) incorrectly returning a
length of 0 when the length to receive is actually greater than zero.
skb->len is already correctly set in ip6_input_finish() with
pskb_pull(), so use skb->len as it always returns the correct result
for both linear and paged data.
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey reported a out-of-bound access in ip6_tnl_xmit(), this
is because we use an ipv4 dst in ip6_tnl_xmit() and cast an IPv4
neigh key as an IPv6 address:
neigh = dst_neigh_lookup(skb_dst(skb),
&ipv6_hdr(skb)->daddr);
if (!neigh)
goto tx_err_link_failure;
if (addr_type == IPV6_ADDR_ANY)
addr6 = &ipv6_hdr(skb)->daddr;
memcpy(&fl6->daddr, addr6, sizeof(fl6->daddr));
Also the network header of the skb at this point should be still IPv4
for 4in6 tunnels, we shold not just use it as IPv6 header.
This patch fixes it by checking if skb->protocol is ETH_P_IPV6: if it
is, we are safe to do the nexthop lookup using skb_dst() and
ipv6_hdr(skb)->daddr; if not (aka IPv4), we have no clue about which
dest address we can pick here, we have to rely on callers to fill it
from tunnel config, so just fall to ip6_route_output() to make the
decision.
Fixes: ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel endpoints.") Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a parent macvlan device is destroyed we end up purging its
broadcast queue without dropping the device reference count on
the packet source device. This causes the source device to linger.
This patch drops that reference count.
Fixes: 260916dfb48c ("macvlan: Fix potential use-after free for...") Reported-by: Joe Ghalam <Joe.Ghalam@dell.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov reported a BUG caused by the ip6mr code which is caused
because we call unregister_netdevice_many for a device that is already
being destroyed. In IPv4's ipmr that has been resolved by two commits
long time ago by introducing the "notify" parameter to the delete
function and avoiding the unregister when called from a notifier, so
let's do the same for ip6mr.
Reducing real_num_tx_queues needs to be in sync with skb queue_mapping
otherwise skbs with queue_mapping greater than real_num_tx_queues
can be sent to the underlying driver and can result in kernel panic.
One such event is running netconsole and enabling VF on the same
device. Or running netconsole and changing number of tx queues via
ethtool on same device.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey's syzkaller program passes rtmsg.rtmsg_flags with the RTF_PCPU bit
set. Flags passed to the kernel are blindly copied to the allocated
rt6_info by ip6_route_info_create making a newly inserted route appear
as though it is a per-cpu route. ip6_rt_cache_alloc sees the flag set
and expects rt->dst.from to be set - which it is not since it is not
really a per-cpu copy. The subsequent call to __ip6_dst_alloc then
generates the fault.
Fix by checking for the flag and failing with EINVAL.
Fixes: d52d3997f843f ("ipv6: Create percpu rt6_info") Reported-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Martin KaFai Lau <kafai@fb.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is prompted by a static checker warning about a potential
use after free. The concern is that netif_rx_ni() can free "skb" and we
call it twice.
When I look at the commit that added this, it looks like some stray
lines were added accidentally. It doesn't make sense to me that we
would recieve the same data two times. I asked the author but never
recieved a response.
I can't test this code, but I'm pretty sure my patch is correct.
Fixes: 4b063258ab93 ("dp83640: Delay scheduled work.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Stefan Sørensen <stefan.sorensen@spectralink.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: cd8ae85299d5 ("tcp: provide SYN headers for passive connections") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now sctp doesn't check sock's state before listening on it. It could
even cause changing a sock with any state to become a listening sock
when doing sctp_listen.
This patch is to fix it by checking sock's state in sctp_listen, so
that it will listen on the sock with right state.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inet_rtm_getroute synthesizes a skeletal ICMP skb, which is passed to
ip_route_input when iif is given. If a multipath route is present for
the designated destination, ip_multipath_icmp_hash ends up being called,
which uses the source/destination addresses within the skb to calculate
a hash. However, those are not set in the synthetic skb, causing it to
return an arbitrary and incorrect result.
Instead, use UDP, which gets no such special treatment.
Signed-off-by: Florian Larysch <fl@n621.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: f1f39f911027 ("l2tp: auto load type modules") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Take a reference on the sessions returned by l2tp_session_find_nth()
(and rename it l2tp_session_get_nth() to reflect this change), so that
caller is assured that the session isn't going to disappear while
processing it.
For procfs and debugfs handlers, the session is held in the .start()
callback and dropped in .show(). Given that pppol2tp_seq_session_show()
dereferences the associated PPPoL2TP socket and that
l2tp_dfs_seq_session_show() might call pppol2tp_show(), we also need to
call the session's .ref() callback to prevent the socket from going
away from under us.
Fixes: fd558d186df2 ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts") Fixes: 0ad6614048cf ("l2tp: Add debugfs files for dumping l2tp debug info") Fixes: 309795f4bec2 ("l2tp: Add netlink control API for L2TP") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calculating po->tp_hdrlen + po->tp_reserve the result can overflow.
Fix by checking that tp_reserve <= INT_MAX on assign.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calculating rb->frames_per_block * req->tp_block_nr the result
can overflow.
Add a check that tp_block_size * tp_block_nr <= UINT_MAX.
Since frames_per_block <= tp_block_size, the expression would
never overflow.
Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Rx path may grab the socket right before pppol2tp_release(), but
nothing guarantees that it will enqueue packets before
skb_queue_purge(). Therefore, the socket can be destroyed without its
queues fully purged.
Fix this by purging queues in pppol2tp_session_destruct() where we're
guaranteed nothing is still referencing the socket.
Fixes: 9e9cb6221aa7 ("l2tp: fix userspace reception on plain L2TP sockets") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the PHY is halted on stop, then do not set the state to PHY_UP. This
ensures the phy will be restarted later in phy_start when the machine is
started again.
Fixes: 00db8189d984 ("This patch adds a PHY Abstraction Layer to the Linux Kernel, enabling ethernet drivers to remain as ignorant as is reasonable of the connected PHY's design and operation details.") Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: Brad Mouring <brad.mouring@ni.com> Acked-by: Xander Huff <xander.huff@ni.com> Acked-by: Kyle Roeschley <kyle.roeschley@ni.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry posted a nice reproducer of a bug triggering in neigh_probe()
when dereferencing a NULL neigh->ops->solicit method.
This can happen for arp_direct_ops/ndisc_direct_ops and similar,
which can be used for NUD_NOARP neighbours (created when dev->header_ops
is NULL). Admin can then force changing nud_state to some other state
that would fire neigh timer.
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit moves sparc64's prototype of pmd_write() outside
of the CONFIG_TRANSPARENT_HUGEPAGE ifdef.
In 2013, commit a7b9403f0e6d ("sparc64: Encode huge PMDs using PTE
encoding.") exposed a path where pmd_write() could be called without
CONFIG_TRANSPARENT_HUGEPAGE defined. This can result in the panic below.
The diff is awkward to read, but the changes are straightforward.
pmd_write() was moved outside of #ifdef CONFIG_TRANSPARENT_HUGEPAGE.
Also, __HAVE_ARCH_PMD_WRITE was defined.
Signed-off-by: Tom Hromatka <tom.hromatka@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I encountered this bug when using /proc/kcore to examine the kernel. Plus a
coworker inquired about debugging tools. We computed pa but did
not use it during the maximum physical address bits test. Instead we used
the identity mapped virtual address which will always fail this test.
I believe the defect came in here:
[bpicco@zareason linus.git]$ git describe --contains bb4e6e85daa52
v3.18-rc1~87^2~4
.
Signed-off-by: Bob Picco <bob.picco@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On slow platforms with unreliable TSC, such as QEMU emulated machines,
it is possible for the kernel to request the next event in the past. In
that case, in the current implementation of xen_vcpuop_clockevent, we
simply return -ETIME. To be precise the Xen returns -ETIME and we pass
it on. However the result of this is a missed event, which simply causes
the kernel to hang.
Instead it is better to always ask the hypervisor for a timer event,
even if the timeout is in the past. That way there are no lost
interrupts and the kernel survives. To do that, remove the
VCPU_SSHOTTMR_future flag.
buflen by default (256) is smaller than wMaxPacketSize (512) in high-speed
devices.
That caused the OUT endpoint to freeze if the host send any data packet of
length greater than 256 bytes.
This is an example dump of what happended on that enpoint:
HOST: [DATA][Length=260][...]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
HOST: [PING]
DEVICE: [NAK]
...
HOST: [PING]
DEVICE: [NAK]
This patch fixes this problem by setting the minimum usb_request's buffer size
for the OUT endpoint as its wMaxPacketSize.
Acked-by: Michal Nazarewicz <mina86@mina86.com> Signed-off-by: Felipe F. Tonello <eu@felipetonello.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the resolution of a regulator's supply, we may attempt to enable
the supply if the regulator itself is already enabled. If enabling the
supply fails, then we will call _regulator_put() for the supply.
However, the pointer to the supply has not been cleared for the
regulator and this will cause a crash if we then unregister the
regulator and attempt to call regulator_put() a second time for the
supply. Fix this by clearing the supply pointer if enabling the supply
after fails when resolving the supply for a regulator.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two different threads with different rds sockets may be in
rds_recv_rcvbuf_delta() via receive path. If their ports
both map to the same word in the congestion map, then
using non-atomic ops to update it could cause the map to
be incorrect. Lets use atomics to avoid such an issue.
Full credit to Wengang <wen.gang.wang@oracle.com> for
finding the issue, analysing it and also pointing out
to offending code with spin lock based fix.
Reviewed-by: Leon Romanovsky <leon@leon.nu> Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CPU1:
mirred_device_event():
spin_lock_bh(&mirred_list_lock);
list_for_each_entry(m, &mirred_list, tcfm_list) {
if (rcu_access_pointer(m->tcfm_dev) == dev) {
dev_put(dev);
/* Note : no rcu grace period necessary, as
* net_device are already rcu protected.
*/
RCU_INIT_POINTER(m->tcfm_dev, NULL);
}
}
spin_unlock_bh(&mirred_list_lock);
CPU0:
tcf_mirred_release():
spin_lock_bh(&mirred_list_lock);
list_del(&m->tcfm_list);
spin_unlock_bh(&mirred_list_lock);
if (dev) // <======== Stil refers to the old m->tcfm_dev
dev_put(dev); // <======== dev_put() is called on it again
The action init code path is good because it is impossible to modify
an action that is being removed.
So, fix this by moving everything under the spinlock.
Fixes: 2ee22a90c7af ("net_sched: act_mirred: remove spinlock in fast path") Fixes: 6bd00b850635 ("act_mirred: fix a race condition on mirred_list") Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The label lio_xmit_failed is used 3 times through liquidio_xmit() but it
always makes a call to dma_unmap_single() using potentially
uninitialized variables from "ndata" variable. Out of the 3 gotos, 2 run
after ndata has been initialized, and had a prior dma_map_single() call.
Fix this by adding a new error label: lio_xmit_dma_failed which does
this dma_unmap_single() and then processed with the lio_xmit_failed
fallthrough.
Fixes: f21fb3ed364bb ("Add support of Cavium Liquidio ethernet adapters") Reported-by: coverity (CID 1309740) Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of handling a crash on an SMP system, an IPI is send to
all other CPUs to save their current registers and stop. It was
using task_pt_regs(current) to get the registers, but that will
only be accurate if the CPU was interrupted running in userland.
Instead allow the architecture to pass in the registers (all
pass NULL now, but allow for the future) and then use get_irq_regs()
which should be accurate as we are in an interrupt. Fall back to
task_pt_regs(current) if nothing else is available.
If first_bad == this_sector when we get the WriteMostly disk
in read_balance(), valid disk will be returned with zero
max_sectors. It'll lead to a dead loop in make_request(), and
OOM will happen because of endless allocation of struct bio.
Since we can't get data from this disk in this case, so
continue for another disk.
Signed-off-by: Wei Fang <fangwei1@huawei.com> Signed-off-by: Shaohua Li <shli@fb.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the initial value of i is greater than zero,
it may cause endless loop, resulting in array out
of bounds, fix it.
This is a port of the radeon fix to amdgpu.
Signed-off-by: tom will <os@iscas.ac.cn> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__test_aead() reads MAX_IVLEN bytes from template[i].iv, but the
actual length of the initialisation vector can be shorter.
The length of the IV is already calculated earlier in the
function. Let's just reuses that. Also the IV length is currently
calculated several time for no reason. Let's fix that too.
This fix an out-of-bound error detected by KASan.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for APB0 in H3. It seems to be compatible with
earlier SOCs. apb0 gates controls R_ block peripherals (R_PIO, R_IR,
etc).
Since this gates behave just like any Allwinner clock gate, add a generic
compatible that can be reused if we don't have any clock to protect.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
[Maxime: Removed the H3 compatible from the simple-gates driver, reworked
the commit log a bit] Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.
While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.
Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Cc: Julia Lawall <julia.lawall@lip6.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
