Felix Fietkau [Sun, 7 Oct 2012 23:23:47 +0000 (23:23 +0000)]
ixp4xx: update Gateworks Avila board support
Several new features for newer boards:
- add additional UARTs present on some boards
- add additional LEDs present on some boards
- add HSS audio device codec present on some boards
- add support for GSC present on some boards
- add per model setup support for newer boards
- set FLASH window per-model for boards with larger FLASH
Some fixes:
- add IRQ mapping for additional PCI devices (USB Host)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 33647
Felix Fietkau [Sun, 7 Oct 2012 23:23:34 +0000 (23:23 +0000)]
ixp4xx: update Gateworks Cambria board support
Several new features for newer boards:
- add irq mapping for additional devices
- add platform data for i2c bus to SFP modules
- add additional UARTs present on some boards
- increased R/W delay for expansion bus UARTs
- add additional LEDs present on some boards
- add GPIO exports and configuration
- add ENET switch config present on some boards
- add support for GSC present on some boards
- added per model setup support for newer boards
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
SVN-Revision: 33644
Hauke Mehrtens [Thu, 4 Oct 2012 21:39:22 +0000 (21:39 +0000)]
acx-mac80211: adapt interface changes in mac80211
The prototype of conf_tx and tx in struct ieee80211_ops changed some
time ago and was not compatible with the prototype assumes by
acs-mac80211.
At least I do not see any compile warnings about this any more.
Hauke Mehrtens [Thu, 4 Oct 2012 15:45:54 +0000 (15:45 +0000)]
bcma: do not initialize deactivated PCIe cores
Before it was tried to initialize the deactivated PCIe core in client
mode, but this causes the SoC to hang. Just do not initialize it at all
and ignore the core it is not working and nothing is connected to it
when the specific bit is set in the boardflags.
Gabor Juhos [Thu, 4 Oct 2012 06:34:14 +0000 (06:34 +0000)]
mac80211/rt2x00: fix lna assignment typo in Rt3352 which went upstream
Reviewing what went into wireless-testing I found a quite nasty mistake,
probably a result of copy&past'ing from the lines below in rt2800lib.c.
This adds another patch to fix that.
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33616
Gabor Juhos [Thu, 4 Oct 2012 06:34:12 +0000 (06:34 +0000)]
mac80211/rt2x00: sync Rt3352 support
The original patch was accepted into linux-next in a slightly modified form.
In order to provide integrity to follow-up patches, replace the patch in OpenWrt
with the (semantically identical) now upstream patch.
(commit 03839951515b0ea2b21d649b1fe7b63f9817d0c8 in wireless-testing)
Signed-off-by: Daniel Golle <dgolle@allnet.de>
SVN-Revision: 33615
Gabor Juhos [Thu, 4 Oct 2012 06:34:09 +0000 (06:34 +0000)]
ramips: add image for ALL0256N-8M
The new version of the ALL0256N now got 8MB SPI NOR flash instead of 4MB.
In order to expose the whole amount of flash, add another image which contains
the corresponding GENERIC_8M mtdparts.
bcma: use fallback sprom if sprom on card was not valid
Sometimes the PCIe card indicates that it has a sprom somewhere and we
are able to read the memory region, but it is empty and not valid. In
these cases we should try to use the fallback sprom as a last chance.
The chip common and the PCIe code are accessing the sprom struct which
is not filled when these cores are initialized. Fix this by adding an
early initialize and fill the sprom struct before accessing it in other
code.
The bcma based SoCs with a ieee80211 core on the SoC and an other
connected via PCIe or USB store the sprom for the SoC with a sb/1/
prefix. The SoC with just one wifi core do not use prefixes. The
BCM4706 do not use a prefix for the SoC part at all, because the prefix
is the path to the ieee80211 core and there is non on the BCM4706.
activate failsafe on all ports of the switch and not just port 0.
Sometimes the port 0 was the WAN port or there could be some device
where the port 0 is not wired to an actual Ethernet port. Now telnet in
failsafe will listen on all ports of the switch so user do not have to
search for the correct port any more. This change will make the switch
leak traffic between the WAN and the LAN port, but you should not use
failsafe while connected to a untrusted network.
ar71xx: create 'fat' images for the DIR-825/TEW-673GRU boards
With these images, it is possible to use the 'unused'
partition of the flash. The 'fat' images can be installed
with the sysupgrade command. When a 'fat' image is
installed from a regular one, the platform specific
sysupgrade script copies the calibration data to the
end of the flash. Likewise, when a regular image is
installed from the 'fat' version the sysupgrade script
copies the calibration data back to the original location.
Felix Fietkau [Mon, 24 Sep 2012 15:23:57 +0000 (15:23 +0000)]
openssl: use asm SHA1, SHA256, AES on MIPS.
On a lightly loaded 24Kc, as measured by 'openssl speed sha1', shows between
27% and 120% speedup depending on block size.
SHA1 is notably used in Transmission for piece verification.
Patch by Catalin Patulea
projects / thirdparty / openwrt.git / log
