Mark Brown [Tue, 13 Jan 2026 12:07:09 +0000 (12:07 +0000)]
regulator: Add TPS65185
Merge series from Andreas Kemnade <andreas@kemnade.info>:
Add a driver for the TPS65185 regulator which provides the
comparatively high voltages needed for electronic paper displays.
Datasheet for the TPS65185 is at https://www.ti.com/lit/gpn/tps65185
To simplify things, include the hwmon part directly which is only
one temperature sensor and there are no other functions besides regulators
in this chip.
Ben Dooks [Mon, 12 Jan 2026 15:49:09 +0000 (15:49 +0000)]
regulator: dummy, make dummy_regulator_driver static
When converting to faux_device the dummy_regulator_driver was
made non-static however it isn't exported or defined anywhere
outside the file it is in. Make it static to avoid the following
sparse warning:
drivers/regulator/dummy.c:59:24: warning: symbol 'dummy_regulator_driver' was not declared. Should it be static?
Andreas Kemnade [Fri, 2 Jan 2026 10:13:57 +0000 (11:13 +0100)]
regulator: Add TPS65185 driver
Add a driver for the TPS65185 regulator. Implement handling of the various
gpio pins. Because the PWRUP (=enable) pin functionality can be achieved
by just using two bits instead, just ensure that it is set to a stable
value.
Implement the pair of symmetric LDOs as a single regulator because they
share a single voltage set register. As the VCOM regulator sits behind that
machinery, just define that one as a supply.
For simplicity, just add the temperature sensor (depending on external NTC)
directly.
There is a mechanism to measure some kick-back voltage during a defined EPD
operation, to calibrate the VCOM voltage setting and store that
non-volatile in the chip to be the power up default setup. That is not
implemented yet in the driver, but that also means that there is a
non-factory default value in these registers after power-up.
Andreas Kemnade [Fri, 2 Jan 2026 10:13:56 +0000 (11:13 +0100)]
regulator: dt-bindings: Document TI TPS65185
Document the TPS65185. GPIO names are same as in the datasheet except for
the PWRUP pad which is described as "enable". That pin is optional because
the rising edge corresponds to setting one register bit and falling edge
to another register bit.
Mark Brown [Mon, 12 Jan 2026 12:15:35 +0000 (12:15 +0000)]
regulator: core: allow regulator_register() with
Merge series from André Draszik <andre.draszik@linaro.org>:
With these attached patches it becomes possible again to support
hardware designs with multiple PMICs where individual rails of each act
as required supplies for rails of the other (due to the latter being
e.g. always-on), and vice-versa.
Google Pixel 6 and 6 Pro (oriole and raven) are examples of such
designs.
Rather than returning -EPORBE_DEFER in regulator_register() when
set_machine_constraints() fails with -EPROBE_DEFER (due to missing
required supplies), we still allow rail registration and try to
reresolve supplies each time a new rail gets registered.
This is implemented using a bus (regulator bus), which allows the core
to reresolve supplies for regulators that still need them whenever new
regulators (i.e. devices) are added.
Using a bus also solves existing problems around late resolution of
supplies as mentioned in the commit message introducing that bus.
The series starts with a few bug fixes and the last two commits
implement the changes mentioned above, but do depend on the bug fixes.
Linus Torvalds [Mon, 12 Jan 2026 01:07:56 +0000 (15:07 -1000)]
Merge tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fixes from Eric Biggers:
- A couple more fixes for the lib/crypto KUnit tests
- Fix missing MMU protection for the AES S-box
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto: aes: Fix missing MMU protection for AES S-box
MAINTAINERS: add test vector generation scripts to "CRYPTO LIBRARY"
lib/crypto: tests: Fix syntax error for old python versions
lib/crypto: tests: polyval_kunit: Increase iterations for preparekey in IRQs
Linus Torvalds [Sun, 11 Jan 2026 17:27:44 +0000 (07:27 -1000)]
Merge tag 'char-misc-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for some reported issues.
Included in here is:
- much reported rust_binder fix
- counter driver fixes
- new device ids for the mei driver
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
rust_binder: remove spin_lock() in rust_shrink_free_page()
mei: me: add nova lake point S DID
counter: 104-quad-8: Fix incorrect return value in IRQ handler
counter: interrupt-cnt: Drop IRQF_NO_THREAD flag
Linus Torvalds [Sun, 11 Jan 2026 17:11:53 +0000 (07:11 -1000)]
Merge tag 'sched-urgent-2026-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"Fix a crash in sched_mm_cid_after_execve()"
* tag 'sched-urgent-2026-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/mm_cid: Prevent NULL mm dereference in sched_mm_cid_after_execve()
Linus Torvalds [Sun, 11 Jan 2026 16:36:20 +0000 (06:36 -1000)]
Merge tag 'irq-urgent-2026-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull misc irqchip fixes from Ingo Molnar:
- Fix an endianness bug in the gic-v5 irqchip driver
- Revert a broken commit from the riscv-imsic irqchip driver
* tag 'irq-urgent-2026-01-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "irqchip/riscv-imsic: Embed the vector array in lpriv"
irqchip/gic-v5: Fix gicv5_its_map_event() ITTE read endianness
Linus Torvalds [Sun, 11 Jan 2026 01:54:41 +0000 (15:54 -1000)]
Merge tag 'riscv-for-linus-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"Notable changes include a fix to close one common microarchitectural
attack vector for out-of-order cores. Another patch exposed an
omission in my boot test coverage, which is currently missing
relocatable kernels. Otherwise, the fixes seem to be settling down for
us.
- Fix CONFIG_RELOCATABLE=y boots by building Image files from
vmlinux, rather than vmlinux.unstripped, now that the .modinfo
section is included in vmlinux.unstripped
- Prevent branch predictor poisoning microarchitectural attacks that
use the syscall index as a vector by using array_index_nospec() to
clamp the index after the bounds check (as x86 and ARM64 already
do)
- Fix a crash in test_kprobes when building with Clang
- Fix a deadlock possible when tracing is enabled for SBI ecalls
- Fix the definition of the Zk standard RISC-V ISA extension bundle,
which was missing the Zknh extension
- A few other miscellaneous non-functional cleanups, removing unused
macros, fixing an out-of-date path in code comments, resolving a
compile-time warning for a type mismatch in a pr_crit(), and
removing an unnecessary header file inclusion"
* tag 'riscv-for-linus-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: trace: fix snapshot deadlock with sbi ecall
riscv: remove irqflags.h inclusion in asm/bitops.h
riscv: cpu_ops_sbi: smp_processor_id() returns int, not unsigned int
riscv: configs: Clean up references to non-existing configs
riscv: kexec_image: Fix dead link to boot-image-header.rst
riscv: pgtable: Cleanup useless VA_USER_XXX definitions
riscv: cpufeature: Fix Zk bundled extension missing Zknh
riscv: fix KUnit test_kprobes crash when building with Clang
riscv: Sanitize syscall table indexing under speculation
riscv: boot: Always make Image from vmlinux, not vmlinux.unstripped
Linus Torvalds [Sun, 11 Jan 2026 00:57:55 +0000 (14:57 -1000)]
Merge tag 'linux_kselftest-fixes-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan:
"Fix tracing test_multiple_writes stalls when buffer_size_kb is less
than 12KB"
* tag 'linux_kselftest-fixes-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests/tracing: Fix test_multiple_writes stall
Linus Torvalds [Sat, 10 Jan 2026 17:14:40 +0000 (07:14 -1000)]
Merge tag 'iommu-fixes-v6.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iomu fixes from Joerg Roedel:
- several Kconfig-related build fixes
- fix for when gcc 8.5 on PPC refuses to inline a function from a
header file
* tag 'iommu-fixes-v6.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
iommupt: Make pt_feature() always_inline
iommufd/selftest: Prevent module/builtin conflicts in kconfig
iommufd/selftest: Add missing kconfig for DMA_SHARED_BUFFER
iommupt: Fix the kunit building
Gao Xiang [Sat, 10 Jan 2026 11:47:03 +0000 (19:47 +0800)]
erofs: fix file-backed mounts no longer working on EROFS partitions
Sheng Yong reported [1] that Android APEX images didn't work with commit 072a7c7cdbea ("erofs: don't bother with s_stack_depth increasing for
now") because "EROFS-formatted APEX file images can be stored within an
EROFS-formatted Android system partition."
In response, I sent a quick fat-fingered [PATCH v3] to address the
report. Unfortunately, the updated condition was incorrect:
The condition `!sb->s_bdev` is always true for all file-backed EROFS
mounts, making the check effectively a no-op.
The real fix tested and confirmed by Sheng Yong [2] at that time was
[PATCH v3 RESEND], which correctly ensures the following EROFS^2 setup
works:
EROFS (on a block device) + EROFS (file-backed mount)
But sadly I screwed it up again by upstreaming the outdated [PATCH v3].
This patch applies the same logic as the delta between the upstream
[PATCH v3] and the real fix [PATCH v3 RESEND].
Jason Gunthorpe [Fri, 9 Jan 2026 14:29:52 +0000 (10:29 -0400)]
iommupt: Make pt_feature() always_inline
gcc 8.5 on powerpc does not automatically inline these functions even
though they evaluate to constants in key cases. Since the constant
propagation is essential for some code elimination and built-time checks
this causes a build failure:
if (pts_feature(&pts, PT_FEAT_DMA_INCOHERENT) &&
!pt_test_sw_bit_acquire(&pts,
SW_BIT_CACHE_FLUSH_DONE))
flush_writes_item(&pts);
Where pts_feature() evaluates to a constant false. Mark them as
__always_inline to force it to evaluate to a constant and trigger the code
elimination.
Fixes: 7c5b184db714 ("genpt: Generic Page Table base API") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202512230720.9y9DtWIo-lkp@intel.com/ Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Jason Gunthorpe [Tue, 6 Jan 2026 19:22:12 +0000 (15:22 -0400)]
iommufd/selftest: Prevent module/builtin conflicts in kconfig
The selftest now depends on the AMDv1 page table, however the selftest
kconfig itself is just an sub-option of the main IOMMUFD module kconfig.
This means it cannot be modular and so kconfig allowed a modular
IOMMU_PT_AMDV1 with a built in IOMMUFD. This causes link failures:
ld: vmlinux.o: in function `mock_domain_alloc_pgtable.isra.0':
selftest.c:(.text+0x12e8ad3): undefined reference to `pt_iommu_amdv1_init'
ld: vmlinux.o: in function `BSWAP_SHUFB_CTL':
sha1-avx2-asm.o:(.rodata+0xaa36a8): undefined reference to `pt_iommu_amdv1_read_and_clear_dirty'
ld: sha1-avx2-asm.o:(.rodata+0xaa36f0): undefined reference to `pt_iommu_amdv1_map_pages'
ld: sha1-avx2-asm.o:(.rodata+0xaa36f8): undefined reference to `pt_iommu_amdv1_unmap_pages'
ld: sha1-avx2-asm.o:(.rodata+0xaa3720): undefined reference to `pt_iommu_amdv1_iova_to_phys'
Adjust the kconfig to disable IOMMUFD_TEST if IOMMU_PT_AMDV1 is incompatible.
Fixes: e93d5945ed5b ("iommufd: Change the selftest to use iommupt instead of xarray") Suggested-by: Arnd Bergmann <arnd@arndb.de> Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202512210135.freQWpxa-lkp@intel.com/ Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Jason Gunthorpe [Tue, 6 Jan 2026 19:22:11 +0000 (15:22 -0400)]
iommufd/selftest: Add missing kconfig for DMA_SHARED_BUFFER
The test doesn't build without it, dma-buf.h does not provide stub
functions if it is not enabled. Compilation can fail with:
ERROR:root:ld: vmlinux.o: in function `iommufd_test':
(.text+0x3b1cdd): undefined reference to `dma_buf_get'
ld: (.text+0x3b1d08): undefined reference to `dma_buf_put'
ld: (.text+0x3b2105): undefined reference to `dma_buf_export'
ld: (.text+0x3b211f): undefined reference to `dma_buf_fd'
ld: (.text+0x3b2e47): undefined reference to `dma_buf_move_notify'
Add the missing select.
Fixes: d2041f1f11dd ("iommufd/selftest: Add some tests for the dmabuf flow") Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Jason Gunthorpe [Tue, 6 Jan 2026 19:22:10 +0000 (15:22 -0400)]
iommupt: Fix the kunit building
The kunit doesn't work since the below commit made GENERIC_PT
unselectable:
$ make ARCH=x86_64 O=build_kunit_x86_64 olddefconfig
ERROR:root:Not all Kconfig options selected in kunitconfig were in the generated .config.
This is probably due to unsatisfied dependencies.
Missing: CONFIG_DEBUG_GENERIC_PT=y, CONFIG_IOMMUFD_TEST=y,
CONFIG_IOMMU_PT_X86_64=y, CONFIG_GENERIC_PT=y, CONFIG_IOMMU_PT_AMDV1=y,
CONFIG_IOMMU_PT_VTDSS=y, CONFIG_IOMMU_PT=y, CONFIG_IOMMU_PT_KUNIT_TEST=y
Also remove the unneeded CONFIG_IOMMUFD_TEST reference as the iommupt kunit
doesn't interact with iommufd, and it doesn't currently build for the
kunit due problems with DMA_SHARED buffer either.
Fixes: 01569c216dde ("genpt: Make GENERIC_PT invisible") Fixes: 1dd4187f53c3 ("iommupt: Add a kunit test for Generic Page Table") Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Linus Torvalds [Sat, 10 Jan 2026 05:34:50 +0000 (19:34 -1000)]
Merge tag 'erofs-for-6.19-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fix from Gao Xiang:
- Don't increase s_stack_depth which caused regressions in some
composefs mount setups (EROFS + ovl^2)
Instead just allow one extra unaccounted fs stacking level for
straightforward cases.
* tag 'erofs-for-6.19-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: don't bother with s_stack_depth increasing for now
Gao Xiang [Thu, 8 Jan 2026 02:38:31 +0000 (10:38 +0800)]
erofs: don't bother with s_stack_depth increasing for now
Previously, commit d53cd891f0e4 ("erofs: limit the level of fs stacking
for file-backed mounts") bumped `s_stack_depth` by one to avoid kernel
stack overflow when stacking an unlimited number of EROFS on top of
each other.
This fix breaks composefs mounts, which need EROFS+ovl^2 sometimes
(and such setups are already used in production for quite a long time).
One way to fix this regression is to bump FILESYSTEM_MAX_STACK_DEPTH
from 2 to 3, but proving that this is safe in general is a high bar.
After a long discussion on GitHub issues [1] about possible solutions,
one conclusion is that there is no need to support nesting file-backed
EROFS mounts on stacked filesystems, because there is always the option
to use loopback devices as a fallback.
As a quick fix for the composefs regression for this cycle, instead of
bumping `s_stack_depth` for file backed EROFS mounts, we disallow
nesting file-backed EROFS over EROFS and over filesystems with
`s_stack_depth` > 0.
This works for all known file-backed mount use cases (composefs,
containerd, and Android APEX for some Android vendors), and the fix is
self-contained.
Essentially, we are allowing one extra unaccounted fs stacking level of
EROFS below stacking filesystems, but EROFS can only be used in the read
path (i.e. overlayfs lower layers), which typically has much lower stack
usage than the write path.
We can consider increasing FILESYSTEM_MAX_STACK_DEPTH later, after more
stack usage analysis or using alternative approaches, such as splitting
the `s_stack_depth` limitation according to different combinations of
stacking.
Linus Torvalds [Sat, 10 Jan 2026 01:42:46 +0000 (15:42 -1000)]
Merge tag 'block-6.19-20260109' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull block fixes from Jens Axboe:
- Kill unlikely checks for blk-rq-qos. These checks are really
all-or-nothing, either the branch is taken all the time, or it's not.
Depending on the configuration, either one of those cases may be
true. Just remove the annotation
- Fix for merging bios with different app tags set
- Fix for a recently introduced slowdown due to RCU synchronization
- Fix for a status change on loop while it's in use, and then a later
fix for that fix
- Fix for the async partition scanning in ublk
* tag 'block-6.19-20260109' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
ublk: fix use-after-free in ublk_partition_scan_work
blk-mq: avoid stall during boot due to synchronize_rcu_expedited
loop: add missing bd_abort_claiming in loop_set_status
block: don't merge bios with different app_tags
blk-rq-qos: Remove unlikely() hints from QoS checks
loop: don't change loop device under exclusive opener in loop_set_status
Linus Torvalds [Sat, 10 Jan 2026 01:21:15 +0000 (15:21 -1000)]
Merge tag 'io_uring-6.19-20260109' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux
Pull io_uring fixes from Jens Axboe:
"A single fix for a regression introduced in 6.15, where a failure to
wake up idle io-wq workers at ring exit will wait for the timeout to
expire.
This isn't normally noticeable, as the exit is async.
But if a parent task created a thread that sets up a ring and uses
requests that cause io-wq threads to be created, and the parent task
then waits for the thread to exit, then it can take 5 seconds for that
pthread_join() to succeed as the child thread is waiting for its
children to exit.
On top of that, just a basic cleanup as well"
* tag 'io_uring-6.19-20260109' of git://git.kernel.org/pub/scm/linux/kernel/git/axboe/linux:
io_uring/io-wq: remove io_wq_for_each_worker() return value
io_uring/io-wq: fix incorrect io_wq_for_each_worker() termination logic
Linus Torvalds [Sat, 10 Jan 2026 01:17:48 +0000 (15:17 -1000)]
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Do not return false if !preemptible() in current_in_efi(). EFI
runtime services can now run with preemption enabled
- Fix uninitialised variable in the arm MPAM driver, reported by sparse
- Fix partial kasan_reset_tag() use in change_memory_common() when
calculating page indices or comparing ranges
- Save/restore TCR2_EL1 during suspend/resume, otherwise the E0POE bit
is lost
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix cleared E0POE bit after cpu_suspend()/resume()
arm64: mm: Fix incomplete tag reset in change_memory_common()
arm_mpam: Stop using uninitialized variables in __ris_msmon_read()
arm64/efi: Don't fail check current_in_efi() if preemptible
Linus Torvalds [Sat, 10 Jan 2026 01:05:19 +0000 (15:05 -1000)]
Merge tag 'ceph-for-6.19-rc5' of https://github.com/ceph/ceph-client
Pull ceph fixes from Ilya Dryomov:
"A bunch of libceph fixes split evenly between memory safety and
implementation correctness issues (all marked for stable) and a change
in maintainers for CephFS: Slava and Alex have formally taken over
Xiubo's role"
* tag 'ceph-for-6.19-rc5' of https://github.com/ceph/ceph-client:
libceph: make calc_target() set t->paused, not just clear it
libceph: reset sparse-read state in osd_fault()
libceph: return the handler error from mon_handle_auth_done()
libceph: make free_choose_arg_map() resilient to partial allocation
ceph: update co-maintainers list in MAINTAINERS
libceph: replace overzealous BUG_ON in osdmap_apply_incremental()
libceph: prevent potential out-of-bounds reads in handle_auth_done()
Fushuai Wang [Fri, 9 Jan 2026 03:36:20 +0000 (11:36 +0800)]
selftests/tracing: Fix test_multiple_writes stall
When /sys/kernel/tracing/buffer_size_kb is less than 12KB,
the test_multiple_writes test will stall and wait for more
input due to insufficient buffer space.
Check current buffer_size_kb value before the test. If it is
less than 12KB, it temporarily increase the buffer to 12KB,
and restore the original value after the tests are completed.
Link: https://lore.kernel.org/r/20260109033620.25727-1-fushuai.wang@linux.dev Fixes: 37f46601383a ("selftests/tracing: Add basic test for trace_marker_raw file") Suggested-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Fushuai Wang <wangfushuai@baidu.com> Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Linus Torvalds [Fri, 9 Jan 2026 17:02:38 +0000 (07:02 -1000)]
Merge tag 'for-6.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- fix potential NULL pointer dereference when replaying tree log after
an error
- release path before initializing extent tree to avoid potential
deadlock when allocating new inode
- on filesystems with block size > page size
- fix potential read out of bounds during encoded read of an inline
extent
- only enforce free space tree if v1 cache is required
- print correct tree id in error message
* tag 'for-6.19-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: show correct warning if can't read data reloc tree
btrfs: fix NULL pointer dereference in do_abort_log_replay()
btrfs: force free space tree for bs > ps cases
btrfs: only enforce free space tree if v1 cache is required for bs < ps cases
btrfs: release path before initializing extent tree in btrfs_read_locked_inode()
btrfs: avoid access-beyond-folio for bs > ps encoded writes
Linus Torvalds [Fri, 9 Jan 2026 16:41:10 +0000 (06:41 -1000)]
Merge tag 'pci-v6.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Bjorn Helgaas:
- Remove ASPM L0s support for MSM8996 SoC since we now enable L0s when
advertised, and it caused random hangs on this device (Manivannan
Sadhasivam)
- Fix meson-pcie to report that the link is up while in ASPM L0s or L1,
since those are active states from the software point of view, and
treating the link as down caused config access failures (Bjorn
Helgaas)
- Fix up sparc DTS BAR descriptions that are above 4GB but not marked
as prefetchable, which caused resource assignment and driver probe
failures after we converted from the SPARC pcibios_enable_device() to
the generic version (Ilpo Järvinen)
* tag 'pci-v6.19-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
sparc/PCI: Correct 64-bit non-pref -> pref BAR resources
PCI: meson: Report that link is up while in ASPM L0s and L1 states
PCI: qcom: Remove ASPM L0s support for MSM8996 SoC
Linus Torvalds [Fri, 9 Jan 2026 16:20:15 +0000 (06:20 -1000)]
Merge tag 'acpi-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI support fix from Rafael Wysocki:
"This fixes the ACPI/PCI legacy interrupts (INTx) parsing in the case
when the ACPI Global System Interrupt (GSI) value is a 32-bit one with
the MSB set.
That was interpreted as a negative integer and caused
acpi_pci_link_allocate_irq() to fail and acpi_irq_get_penalty() to
trigger an out-of-bounds array dereference (Lorenzo Pieralisi)"
* tag 'acpi-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: PCI: IRQ: Fix INTx GSIs signedness
Linus Torvalds [Fri, 9 Jan 2026 16:18:05 +0000 (06:18 -1000)]
Merge tag 'pm-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"This fixes a crash in the hibernation image saving code that can be
triggered when the given compression algorithm is unavailable (Malaya
Kumar Rout)"
* tag 'pm-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: Fix crash when freeing invalid crypto compressor
Linus Torvalds [Fri, 9 Jan 2026 16:10:22 +0000 (06:10 -1000)]
Merge tag 'gpio-fixes-for-v6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"There are several ordinary driver fixes and a fix to a race between
the registration of two chips that causes a crash in GPIO core.
The bulk of the changed lines however, concerns the management of
shared GPIOs that landed in v6.19-rc1. Enabling it for ARCH_QCOM
enabled it in defconfig which effectively enabled it for all arm64
platforms and exposed the code to quite a lot of testing (which is
good, right? :)).
As a resukt, I received a number of bug reports, which I progressively
fixed over the course of last weeks. This explains the number of lines
higher than what I normally aim for at this stage.
- balance superio enter/exit calls in error path in gpio-it87
- fix a race where we try to take the SRCU read lock of the GPIO
device before it's been initialized causing a NULL-pointer
dereference
- fix handling of short-pulse interrupts in gpio-pca053x
- fix a reference leak in error path in gpio-mpsse
- mark the GPIO controller as sleeping (it calls sleeping functions)
in gpio-rockchip
- fix several issues in management of shared GPIOs"
* tag 'gpio-fixes-for-v6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: shared: fix a false-positive sharing detection with reset-gpios
gpiolib: fix lookup table matching
gpio: shared: don't allocate the lookup table until we really need it
gpio: shared: fix a race condition
gpio: shared: assign the correct firmware node for reset-gpio use-case
gpio: rockchip: mark the GPIO controller as sleeping
gpio: mpsse: fix reference leak in gpio_mpsse_probe() error paths
gpio: pca953x: handle short interrupt pulses on PCAL devices
gpiolib: fix race condition for gdev->srcu
gpio: shared: allow sharing a reset-gpios pin between reset-gpio and gpiolib
gpio: shared: verify con_id when adding proxy lookup
gpiolib: allow multiple lookup tables per consumer
gpio: it87: balance superio enter/exit calls in error path
Linus Torvalds [Fri, 9 Jan 2026 16:04:05 +0000 (06:04 -1000)]
Merge tag 'drm-fixes-2026-01-09' of https://gitlab.freedesktop.org/drm/kernel
Pull drm fixes from Dave Airlie:
"I missed the drm-rust fixes tree for last week, so this catches up on
that, along with amdgpu, and then some misc fixes across a few
drivers. I hadn't got an xe pull by the time I sent this, I suspect
one will arrive 10 mins after, but I don't think there is anything
that can't wait for next week.
Things seem to have picked up a little with people coming back from
holidays,
MAINTAINERS:
- Fix Nova GPU driver git links
- Fix typo in TYR driver entry preventing correct behavior of
scripts/get_maintainer.pl
- Exclude TYR driver from DRM MISC
nova-core:
- Correctly select RUST_FW_LOADER_ABSTRACTIONS to prevent build
errors
- Regenerate nova-core bindgen bindings with '--explicit-padding' to
avoid uninitialized bytes
- Fix length of received GSP messages, due to miscalculated message
payload size
- Regenerate bindings to derive MaybeZeroable
- Use a bindings alias to derive the firmware version
exynos:
- hdmi: replace system_wq with system_percpu_wq
pl111:
- Fix error handling in probe
mediatek/atomic/tidss:
- Fix tidss in another way and revert reordering of pre-enable and
post-disable operations, as it breaks other bridge drivers
nouveau:
- Fix regression from fwsec s/r fix
pci/vga:
- Fix multiple gpu's being reported a 'boot_display'
fb-helper:
- Fix vblank timeout during suspend/reset
amdgpu:
- Clang fixes
- Navi1x PCIe DPM fixes
- Ring reset fixes
- ISP suspend fix
- Analog DC fixes
- VPE fixes
- Mode1 reset fix
radeon:
- Variable sized array fix"
* tag 'drm-fixes-2026-01-09' of https://gitlab.freedesktop.org/drm/kernel: (32 commits)
Reapply "Revert "drm/amd: Skip power ungate during suspend for VPE""
drm/amd/display: Check NULL before calling dac_load_detection
drm/amd/pm: Disable MMIO access during SMU Mode 1 reset
drm/exynos: hdmi: replace use of system_wq with system_percpu_wq
drm/fb-helper: Fix vblank timeout during suspend/reset
PCI/VGA: Don't assume the only VGA device on a system is `boot_vga`
drm/amdgpu: Fix query for VPE block_type and ip_count
drm/amd/display: Add missing encoder setup to DACnEncoderControl
drm/amd/display: Correct color depth for SelectCRTC_Source
drm/amd/amdgpu: Fix SMU warning during isp suspend-resume
drm/amdgpu: always backup and reemit fences
drm/amdgpu: don't reemit ring contents more than once
drm/amd/pm: force send pcie parmater on navi1x
drm/amd/pm: fix wrong pcie parameter on navi1x
drm/radeon: Remove __counted_by from ClockInfoArray.clockInfo[]
drm/amd/display: Reduce number of arguments of dcn30's CalculateWatermarksAndDRAMSpeedChangeSupport()
drm/amd/display: Reduce number of arguments of dcn30's CalculatePrefetchSchedule()
drm/amd/display: Apply e4479aecf658 to dml
nouveau: don't attempt fwsec on sb on newer platforms
drm/tidss: Fix enable/disable order
...
Linus Torvalds [Fri, 9 Jan 2026 15:57:57 +0000 (05:57 -1000)]
Merge tag 'vfs-6.19-rc5.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
- Remove incorrect __user annotation from struct xattr_args::value
- Documentation fix: Add missing kernel-doc description for the @isnew
parameter in ilookup5_nowait() to silence Sphinx warnings
- Documentation fix: Fix kernel-doc comment for __start_dirop() - the
function name in the comment was wrong and the @state parameter was
undocumented
- Replace dynamic folio_batch allocation with stack allocation in
iomap_zero_range(). The dynamic allocation was problematic for
ext4-on-iomap work (didn't handle allocation failure properly) and
triggered lockdep complaints. Uses a flag instead to control batch
usage
- Re-add #ifdef guards around PIDFD_GET_<ns-type>_NAMESPACE ioctls.
When a namespace type is disabled, ns->ops is NULL, causes crashes
during inode eviction when closing the fd. The ifdefs were removed in
a recent simplification but are still needed
- Fixe a race where a folio could be unlocked before the trailing zeros
(for EOF within the page) were written
- Split out a dedicated lease_dispose_list() helper since lease code
paths always know they're disposing of leases. Removes unnecessary
runtime flag checks and prepares for upcoming lease_manager
enhancements
- Fix userland delegation requests succeeding despite conflicting
opens. Previously, FL_LAYOUT and FL_DELEG leases bypassed conflict
checks (a hack for nfsd). Adds new ->lm_open_conflict() lease_manager
operation so userland delegations get proper conflict checking while
nfsd can continue its own conflict handling
- Fix LOOKUP_CACHED path lookups incorrectly falling through to the
slow path. After legitimize_links() calls were conditionally elided,
the routine would always fail with LOOKUP_CACHED regardless of
whether there were any links. Now the flag is checked at the two
callsites before calling legitimize_links()
- Fix bug in media fd allocation in media_request_alloc()
- Fix mismatched API calls in ecryptfs_mknod(): was calling
end_removing() instead of end_creating() after
ecryptfs_start_creating_dentry()
- Fix dentry reference count leak in ecryptfs_mkdir(): a dget() of the
lower parent dir was added but never dput()'d, causing BUG during
lower filesystem unmount due to the still-in-use dentry
* tag 'vfs-6.19-rc5.fixes' of gitolite.kernel.org:pub/scm/linux/kernel/git/vfs/vfs:
pidfs: protect PIDFD_GET_* ioctls() via ifdef
ecryptfs: Release lower parent dentry after creating dir
ecryptfs: Fix improper mknod pairing of start_creating()/end_removing()
get rid of bogus __user in struct xattr_args::value
VFS: fix __start_dirop() kernel-doc warnings
fs: Describe @isnew parameter in ilookup5_nowait()
fs: make sure to fail try_to_unlazy() and try_to_unlazy() for LOOKUP_CACHED
netfs: Fix early read unlock of page with EOF in middle
filelock: allow lease_managers to dictate what qualifies as a conflict
filelock: add lease_dispose_list() helper
iomap: replace folio_batch allocation with stack allocation
media: mc: fix potential use-after-free in media_request_alloc()
Anup Patel [Tue, 23 Dec 2025 14:35:44 +0000 (20:05 +0530)]
Revert "irqchip/riscv-imsic: Embed the vector array in lpriv"
The __alloc_percpu() fails when the number of IDs are greater than 959
because size parameter of __alloc_percpu() must be less than 32768 (aka
PCPU_MIN_UNIT_SIZE). This failure is observed with KVMTOOL when AIA is
trap-n-emulated by in-kernel KVM because in this case KVM guest has 2047
interrupt IDs.
To address this issue, don't embed vector array in struct imsic_local_priv
until __alloc_percpu() support size parameter greater than 32768.
This reverts commit 79eaabc61dfb ("irqchip/riscv-imsic: Embed the vector
array in lpriv").
Ming Lei [Fri, 9 Jan 2026 12:14:54 +0000 (20:14 +0800)]
ublk: fix use-after-free in ublk_partition_scan_work
A race condition exists between the async partition scan work and device
teardown that can lead to a use-after-free of ub->ub_disk:
1. ublk_ctrl_start_dev() schedules partition_scan_work after add_disk()
2. ublk_stop_dev() calls ublk_stop_dev_unlocked() which does:
- del_gendisk(ub->ub_disk)
- ublk_detach_disk() sets ub->ub_disk = NULL
- put_disk() which may free the disk
3. The worker ublk_partition_scan_work() then dereferences ub->ub_disk
leading to UAF
Fix this by using ublk_get_disk()/ublk_put_disk() in the worker to hold
a reference to the disk during the partition scan. The spinlock in
ublk_get_disk() synchronizes with ublk_detach_disk() ensuring the worker
either gets a valid reference or sees NULL and exits early.
Also change flush_work() to cancel_work_sync() to avoid running the
partition scan work unnecessarily when the disk is already detached.
Fixes: 7fc4da6a304b ("ublk: scan partition in async way") Reported-by: Ruikai Peng <ruikai@pwno.io> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
André Draszik [Fri, 9 Jan 2026 08:38:44 +0000 (08:38 +0000)]
regulator: core: don't fail regulator_register() with missing required supply
Since commit 98e48cd9283d ("regulator: core: resolve supply for
boot-on/always-on regulators"), the regulator core returns
-EPROBE_DEFER if a supply can not be resolved at regulator_register()
time due to set_machine_constraints() requiring that supply (e.g.
because of always-on or boot-on).
In some hardware designs, multiple PMICs are used where individual
rails of each act as supplies for rails of the other, and vice-versa.
In such a design no PMIC driver can probe when registering one top-
level regulator device (as is common practice for almost all regulator
drivers in Linux) since that commit. Supplies are only considered when
their driver has fully bound, but because in a design like the above
two drivers / devices depend on each other, neither will have fully
bound while the other probes. The Google Pixel 6 and 6 Pro (oriole and
raven) are examples of such a design.
One way to make this work would be to register each rail as an
individual device, rather than just one top-level regulator device.
Then, fw-devlink and Linux' driver core could do their usual handling
of deferred device probe as each rail would be probed individually.
This approach was dismissed in [1] as each regulator driver would have
to take care of this itself.
Alternatively, we can change the regulator core to not fail
regulator_register() if a rail's required supply can not be resolved
while keeping the intended change from above mentioned commit, and
instead retry whenever a new rail is registered. This commit implements
such an approach:
If set_machine_constraints() requests probe deferral,
regulator_register() still succeeds and we retry setting
constraints as part of regulator_resolve_supply().
We still do not enable the regulator or allow consumers to use it
until constraints have been set (including resolution of the
supply) to prevent enabling of a regulator before its supply.
With this change, we keep track of regulators with missing required
supplies and can therefore try to resolve them again and try to set
the constraints again once more regulators become available.
Care has to be taken to not allow consumers to use regulators that
haven't had their constraints set yet. regulator_get() ensures that
and now returns -EPROBE_DEFER in that case.
The implementation is straight-forward, thanks to our newly introduced
regulator-bus. Locking in regulator_resolve_supply() has to be done
carefully, as a combination of regulator_(un)lock_two() and
regulator_(un)lock_dependent() is needed. The reason is that
set_machine_constraints() might call regulator_enable() which needs
rdev and all its dependents locked, but everything else requires to
only have rdev and its supply locked.
André Draszik [Fri, 9 Jan 2026 08:38:43 +0000 (08:38 +0000)]
regulator: core: reresolve unresolved supplies when available
When a regulator A and its supply B are provided by different devices,
the driver implementing B might be last to probe (with A still
pending resolution of its supply B). While we try to resolve all
pending supplies for all regulators (including A) during
regulator_register() of B via regulator_register_resolve_supply(),
supply resolution will still not work for A as the driver for B hasn't
finished binding to the PMIC device corresponding to B at that stage
yet. The regulator core explicitly only allows supplies from other
devices to be used once the relevant driver has fully bound, mainly to
avoid having to deal with cases where B itself might -EPROBE_DEFER.
In this case, A's supply will only be resolved as part of the core's
regulator_init_complete_work_function(), which currently is scheduled
to run after 30s. This was added as a work-around in
commit 3827b64dba27 ("regulator: core: Resolve supplies before
disabling unused regulators") to cover this situation.
There are two problems with that approach:
* it potentially runs long after all our consumers have probed
* an upcoming change will allow regulator_register() to complete
successfully even when required supplies (e.g. due to always-on or
boot-on) are missing at register time, deferring full configuration
of the regulator (and usability by consumers, i.e. usually consumer
probe) until the supply becomes available.
Resolving supplies in the late work func can therefore make it
impossible for consumers to probe at all, as the driver core will not
know to reprobe consumers when supplies have resolved.
We could schedule an earlier work to try to resolve supplies sooner,
but that'd be racy as consumers of A might try to probe before A's
supply gets fully resolved via this extra work.
Instead, add a very simple regulator bus and add a dummy device with a
corresponding driver to it for each regulator that is missing its
supply during regulator_register(). This way, the driver core will call
our bus' probe whenever a new (regulator) device was successfully
bound, allowing us to retry resolving the supply during (our bus) probe
and to bind this dummy device if successful. In turn this means the
driver core will see a newly bound device and retry probing of all
pending consumers, if any.
With that in place, we can avoid walking the full list of all known
regulators to try resolve missing supplies during regulator_register(),
as the driver core will invoke the bus probe for regulators that are
still pending their supplies. We can also drop the code trying to
resolve supplies one last time before unused regulators get disabled,
as all supplies should have resolved at that point in time, and if they
haven't then there's no point in trying again, as the outcome won't
change.
Note: We can not reuse the existing struct device created for each
rail, as a device can not be part of a class and a bus simultaneously.
André Draszik [Fri, 9 Jan 2026 08:38:42 +0000 (08:38 +0000)]
regulator: core: don't ignore errors from event forwarding setup
Receiving and forwarding critical supply events seems like they're
important information and we shouldn't ignore errors occurring during
registration for such events.
With this change the supply is unset on event registration failure,
allowing us to potentially retry another time.
André Draszik [Fri, 9 Jan 2026 08:38:41 +0000 (08:38 +0000)]
regulator: core: remove dead code in regulator_resolve_supply()
Since commit 98e48cd9283d ("regulator: core: resolve supply for
boot-on/always-on regulators") we require that a regulator's supply has
been resolved before enabling the regulator. Furthermore,
regulator_get() also fails if the supply hasn't been resolved yet
(preventing consumers from enabling a regulator without its supply
known). In combination this means that regulator_resolve_supply() now
always runs before the regulator has been enabled via
set_machine_constraints().
The code here was meant to run after enabling the regulator in case the
supply hadn't been resolved at that time and can therefore never
execute anymore since that commit.
André Draszik [Fri, 9 Jan 2026 08:38:40 +0000 (08:38 +0000)]
regulator: core: streamline supply resolution for always-on/boot-on regulators
For always-on and boot-on regulators, regulator_register() is currently
trying to anticipate the requirement to resolve a supply early.
Unfortunately, this code executes too early, before we have potentially
updated the regulator's always_on constraint as part of
set_machine_constraints(), causing it to miss cases.
Rather than trying to hack it more, just defer to the outcome of
set_machine_constraints(). The latter returns early (without doing any
regulator initialisation) with -EPROBE_DEFER as of commit 'regulator:
core: move supply check earlier in set_machine_constraints()' and is
therefore safe to call multiple times to determine if supplies need to
be resolved early.
Commit 8a866d527ac0 ("regulator: core: Resolve supply name earlier to
prevent double-init") (later updated by
commit 520fb178212d ("regulator: core: Fix regulator supply
registration with sysfs")) added these tests originally to avoid
calling set_machine_constraints() multiple times to try to avoid
voltage glitches due to all the regulator initialisation happening each
time. This isn't an issue anymore as per above.
André Draszik [Fri, 9 Jan 2026 08:38:39 +0000 (08:38 +0000)]
regulator: core: move supply check earlier in set_machine_constraints()
Since commit 98e48cd9283d ("regulator: core: resolve supply for
boot-on/always-on regulators"), set_machine_constraints() can return
-EPROBE_DEFER very late, after it has done a lot of work and
configuration of the regulator.
This means that configuration will happen multiple times for no
benefit in that case. Furthermore, this can lead to timing-dependent
voltage glitches as mentioned e.g. in commit 8a866d527ac0 ("regulator:
core: Resolve supply name earlier to prevent double-init").
We can know that it's going to fail very early, in particular before
going through the complete regulator configuration by moving some code
around a little.
Do so to avoid re-configuring the regulator multiple times, also
avoiding the voltage glitches if we can.
as the regulator_list_mutex must be held when calling _regulator_put().
To solve this, simply switch to using regulator_put().
While at it, we should also make sure that no concurrent access happens
to our rdev while we clear out the supply pointer. Add appropriate
locking to ensure that.
While the code in question will be removed altogether in a follow-up
commit, I believe it is still beneficial to have this corrected before
removal for future reference.
Fixes: 36a1f1b6ddc6 ("regulator: core: Fix memory leak in regulator_resolve_supply()") Fixes: 8e5356a73604 ("regulator: core: Clear the supply pointer if enabling fails") Signed-off-by: André Draszik <andre.draszik@linaro.org> Link: https://patch.msgid.link/20260109-regulators-defer-v2-2-1a25dc968e60@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org>
(note the missing t in budget). This is because there is a --count just
below the call to scnprintf(), to make space for the comma. All similar
calls to scnprintf() above add an extra space to the format string to
allow for that, but this one doesn't, so the last character t is
stripped instead. Update the format string to fix the message.
2)
Add the name of the supply to the failure message printed when the
supply can not be resolved when debug messages are enabled to help with
debug.
Cong Wang [Tue, 23 Dec 2025 21:51:13 +0000 (13:51 -0800)]
sched/mm_cid: Prevent NULL mm dereference in sched_mm_cid_after_execve()
sched_mm_cid_after_execve() is called in bprm_execve()'s cleanup path even
when exec_binprm() fails. For the init task's first execve(), this causes a
problem:
1. current->mm is NULL (kernel threads don't have an mm)
2. sched_mm_cid_before_execve() exits early because mm is NULL
3. exec_binprm() fails (e.g., ENOENT for missing script interpreter)
4. sched_mm_cid_after_execve() is called with mm still NULL
5. sched_mm_cid_fork() is called unconditionally, triggering WARN_ON
This is easily reproduced by booting with an init that is a shell script
(#!/bin/sh) where the interpreter doesn't exist in the initramfs.
Fix this by checking if t->mm is NULL before calling sched_mm_cid_fork(),
matching the behavior of sched_mm_cid_before_execve() which already
handles this case via sched_mm_cid_exit()'s early return.
Fixes: b0c3d51b54f8 ("sched/mmcid: Provide precomputed maximal value") Signed-off-by: Cong Wang <cwang@multikernel.io> Signed-off-by: Thomas Gleixner <tglx@kernel.org> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Acked-by: Will Deacon <will@kernel.org> Link: https://patch.msgid.link/20251223215113.639686-1-xiyou.wangcong@gmail.com
Yeoreum Yun [Wed, 7 Jan 2026 16:21:15 +0000 (16:21 +0000)]
arm64: Fix cleared E0POE bit after cpu_suspend()/resume()
TCR2_ELx.E0POE is set during smp_init().
However, this bit is not reprogrammed when the CPU enters suspension and
later resumes via cpu_resume(), as __cpu_setup() does not re-enable E0POE
and there is no save/restore logic for the TCR2_ELx system register.
As a result, the E0POE feature no longer works after cpu_resume().
To address this, save and restore TCR2_EL1 in the cpu_suspend()/cpu_resume()
path, rather than adding related logic to __cpu_setup(), taking into account
possible future extensions of the TCR2_ELx feature.
Fixes: bf83dae90fbc ("arm64: enable the Permission Overlay Extension for EL0") Cc: <stable@vger.kernel.org> # 6.12.x Signed-off-by: Yeoreum Yun <yeoreum.yun@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Reviewed-by: Kevin Brodsky <kevin.brodsky@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
gpio: shared: fix a false-positive sharing detection with reset-gpios
After scanning the devicetree, we remove all entries that have only one
reference, while creating GPIO shared proxies for the remaining, shared
entries. However: for the reset-gpio corner-case, we will have two
references for a "reset-gpios" pin that's not really shared. In this
case one will come from the actual consumer fwnode and the other from
the potential auxiliary reset-gpio device. This causes the GPIO core to
create unnecessary GPIO shared proxy devices for pins that are not
really shared.
Add a function that can detect this situation and remove entries that
have exactly two references but one of them is a reset-gpio.
Linus Torvalds [Fri, 9 Jan 2026 02:38:19 +0000 (16:38 -1000)]
Merge tag 'pinctrl-v6.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix the mt8189 register base name order back from being fixed broken
- Add REGMAP_MMIO to the pic64gx-gpio2 to avoid build breakages
- Mark the Qualcomm lpass-lpi pin controller GPIO chip instance as
sleeping to fix lock splats
- Update .mailmap with my new kernel.org address for all old mails
after maintainers ran into issues with this
* tag 'pinctrl-v6.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: qcom: lpass-lpi: mark the GPIO controller as sleeping
pinctrl: pic64gx-gpio2: Add REGMAP_MMIO dependency
Update .mailmap for Linus Walleij
pinctrl: mediatek: mt8189: restore previous register base name array order
Jiayuan Chen [Sun, 4 Jan 2026 12:35:27 +0000 (20:35 +0800)]
arm64: mm: Fix incomplete tag reset in change_memory_common()
Running KASAN KUnit tests with {HW,SW}_TAGS mode triggers a fault in
change_memory_common():
Call trace:
change_memory_common+0x168/0x210 (P)
set_memory_ro+0x20/0x48
vmalloc_helpers_tags+0xe8/0x338
kunit_try_run_case+0x74/0x188
kunit_generic_run_threadfn_adapter+0x30/0x70
kthread+0x11c/0x200
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
# vmalloc_helpers_tags: try faulted
not ok 67 vmalloc_helpers_tags
Commit a06494adb7ef ("arm64: mm: use untagged address to calculate page index")
fixed a KASAN warning in the BPF subsystem by adding kasan_reset_tag() to
the index calculation. In the execmem flow:
The returned address from execmem_vmalloc/execmem_cache_alloc is passed
through kasan_reset_tag(), so start has no tag while area->addr still
retains the original tag. The fix correctly handled this case by resetting
the tag on area->addr:
However, in normal vmalloc paths, both start and area->addr have matching
tags(or no tags). Resetting only area->addr causes a mismatch when
subtracting a tagged address from an untagged one, resulting in an
incorrect index.
Fix this by resetting tags on both addresses in the index calculation.
This ensures correct results regardless of the tag state of either address.
Tested with KASAN KUnit tests under CONFIG_KASAN_GENERIC,
CONFIG_KASAN_SW_TAGS, and CONFIG_KASAN_HW_TAGS - all pass. Also verified
the original BPF KASAN warning from [1] is still fixed.
Eric Biggers [Wed, 7 Jan 2026 05:20:23 +0000 (21:20 -0800)]
lib/crypto: aes: Fix missing MMU protection for AES S-box
__cacheline_aligned puts the data in the ".data..cacheline_aligned"
section, which isn't marked read-only i.e. it doesn't receive MMU
protection. Replace it with ____cacheline_aligned which does the right
thing and just aligns the data while keeping it in ".rodata".
Fixes: b5e0b032b6c3 ("crypto: aes - add generic time invariant AES cipher") Cc: stable@vger.kernel.org Reported-by: Qingfang Deng <dqfext@gmail.com> Closes: https://lore.kernel.org/r/20260105074712.498-1-dqfext@gmail.com/ Acked-by: Ard Biesheuvel <ardb@kernel.org> Link: https://lore.kernel.org/r/20260107052023.174620-1-ebiggers@kernel.org Signed-off-by: Eric Biggers <ebiggers@kernel.org>
lib/crypto: tests: polyval_kunit: Increase iterations for preparekey in IRQs
On my development machine the generic, memcpy()-only implementation of
polyval_preparekey() is too fast for the IRQ workers to actually fire.
The test fails.
Increase the iterations to make the test more robust.
The test will run for a maximum of one second in any case.
[EB: This failure was already fixed by commit c31f4aa8fed0 ("kunit:
Enforce task execution in {soft,hard}irq contexts"). I'm still applying
this patch too, since the iteration count in this test made its running
time much shorter than the other similar ones.]
Ben Horgan [Fri, 19 Dec 2025 18:11:03 +0000 (18:11 +0000)]
arm_mpam: Stop using uninitialized variables in __ris_msmon_read()
Dan has reported two uses of uninitialized variables in __ris_msmon_read().
If an unknown monitor type is encountered then the local variable, now, is
used uninitialized. Fix this by returning early on error. If a non-mbwu
monitor is being read then the local variable, overflow, is not initialized
but still read. Initialize it to false as overflow is not relevant for csu
monitors.
Fixes: 823e7c3712c5 ("arm_mpam: Add mpam_msmon_read() to read monitor value") Fixes: 9e5afb7c3283 ("arm_mpam: Use long MBWU counters if supported") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/r/202512091519.RBwiJcSq-lkp@intel.com/ Closes: https://lore.kernel.org/r/202512100547.N7QPYgfb-lkp@intel.com/ Signed-off-by: Ben Horgan <ben.horgan@arm.com> Reviewed-by: Jonathan Cameron <jonathan.cameron@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Linus Torvalds [Thu, 8 Jan 2026 18:47:05 +0000 (08:47 -1000)]
Merge tag 'trace-v6.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Remove useless assignment of soft_mode variable
The function __ftrace_event_enable_disable() sets "soft_mode" in one
of the branch paths but doesn't use it after that. Remove the setting
of that variable.
- Add a cond_resched() in ring_buffer_resize()
The resize function that allocates all the pages for the ring buffer
was causing a soft lockup on PREEMPT_NONE configs when allocating
large buffers on machines with many CPUs. Hopefully this is the last
cond_resched() needed to be added as PREEMPT_LAZY becomes the norm in
the future.
- Make ftrace_graph_ent depth field signed
The "depth" field of struct ftrace_graph_ent was converted from "int"
to "unsigned long" for alignment reasons to work with being embedded
in other structures. The conversion from a signed to unsigned caused
integrity checks to always pass as they were comparing "depth" to
less than zero. Make the field signed long.
- Add recursion protection to stack trace events
A infinite recursion was triggered by a stack trace event calling RCU
which internally called rcu_read_unlock_special(), which triggered an
event that was also doing stacktraces which cause it to trigger the
same RCU lock that called rcu_read_unlock_special() again.
Update the trace_test_and_set_recursion() to add a set of context
checks for events to use, and have the stack trace event use that for
recursion protection.
- Make the variable ftrace_dump_on_oops static
The cleanup of sysctl that moved all the updates to the files that
use them moved the reference of ftrace_dump_on_oops to where it is
used. It is no longer used outside of the trace.c file. Make it
static.
* tag 'trace-v6.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
trace: ftrace_dump_on_oops[] is not exported, make it static
tracing: Add recursion protection in kernel stack trace recording
ftrace: Make ftrace_graph_ent depth field signed
ring-buffer: Avoid softlockup in ring_buffer_resize() during memory free
tracing: Drop unneeded assignment to soft_mode
- ping: fix ICMP out SNMP stats double-counting with ICMP sockets
- bonding: preserve NETIF_F_ALL_FOR_ALL across TSO updates
- bridge: fix C-VLAN preservation in 802.1ad vlan_tunnel egress
- eth: bnxt: fix potential data corruption with HW GRO/LRO"
* tag 'net-6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
arp: do not assume dev_hard_header() does not change skb->head
net: enetc: fix build warning when PAGE_SIZE is greater than 128K
atm: Fix dma_free_coherent() size
tools: ynl: don't install tests
net: do not write to msg_get_inq in callee
bnxt_en: Fix NULL pointer crash in bnxt_ptp_enable during error cleanup
net: usb: pegasus: fix memory leak in update_eth_regs_async()
net: 3com: 3c59x: fix possible null dereference in vortex_probe1()
net/sched: sch_qfq: Fix NULL deref when deactivating inactive aggregate in qfq_reset
wifi: mac80211: collect station statistics earlier when disconnect
wifi: mac80211: restore non-chanctx injection behaviour
wifi: mac80211_hwsim: disable BHs for hwsim_radio_lock
wifi: mac80211: don't iterate not running interfaces
wifi: mac80211_hwsim: fix typo in frequency notification
wifi: avoid kernel-infoleak from struct iw_point
net: airoha: Fix schedule while atomic in airoha_ppe_deinit()
selftests: netdevsim: add carrier state consistency test
net: netdevsim: fix inconsistent carrier state after link/unlink
selftests: drv-net: Bring back tool() to driver __init__s
net/sched: act_api: avoid dereferencing ERR_PTR in tcf_idrinfo_destroy
...
Jakub Kicinski [Thu, 8 Jan 2026 16:54:54 +0000 (08:54 -0800)]
Merge branch '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-01-06 (idpf)
This series contains updates to idpf driver only.
Emil fixes issues related to resets; among them timeouts, NULL pointer
dereferences, and memory leaks.
Sreedevi resolves issues around RSS; mainly involving operations when
the interface is down and resets. She also addresses some incomplete
cleanups for ntuple filters and interrupts.
Erik fixes incomplete output of ntuple filters.
Josh sets restriction of Rx buffer size to follow hardware restrictions.
Larysa adds check to prevent NULL pointer dereference when RDMA is not
enabled.
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
idpf: fix aux device unplugging when rdma is not supported by vport
idpf: cap maximum Rx buffer size
idpf: Fix error handling in idpf_vport_open()
idpf: Fix RSS LUT NULL ptr issue after soft reset
idpf: Fix RSS LUT configuration on down interfaces
idpf: Fix RSS LUT NULL pointer crash on early ethtool operations
idpf: fix issue with ethtool -n command display
idpf: fix memory leak of flow steer list on rmmod
idpf: fix error handling in the init_task on load
idpf: fix memory leak in idpf_vc_core_deinit()
idpf: fix memory leak in idpf_vport_rel()
idpf: detach and close netdevs while handling a reset
idpf: keep the netdev when a reset fails
====================
Wei Fang [Wed, 7 Jan 2026 09:12:04 +0000 (17:12 +0800)]
net: enetc: fix build warning when PAGE_SIZE is greater than 128K
The max buffer size of ENETC RX BD is 0xFFFF bytes, so if the PAGE_SIZE
is greater than 128K, ENETC_RXB_DMA_SIZE and ENETC_RXB_DMA_SIZE_XDP will
be greater than 0xFFFF, thus causing a build warning.
This will not cause any practical issues because ENETC is currently only
used on the ARM64 platform, and the max PAGE_SIZE is 64K. So this patch
is only for fixing the build warning that occurs when compiling ENETC
drivers for other platforms.
Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202601050637.kHEKKOG7-lkp@intel.com/ Fixes: e59bc32df2e9 ("net: enetc: correct the value of ENETC_RXB_TRUESIZE") Signed-off-by: Wei Fang <wei.fang@nxp.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Link: https://patch.msgid.link/20260107091204.1980222-1-wei.fang@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 8 Jan 2026 16:49:24 +0000 (08:49 -0800)]
Merge tag 'wireless-2026-01-08' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Couple of fixes:
- mac80211:
- long-standing injection bug due to chanctx rework
- more recent interface iteration issue
- collect statistics before removing stations
- hwsim:
- fix NAN frequency typo (potential NULL ptr deref)
- fix locking of radio lock (needs softirqs disabled)
- wext:
- ancient issue with compat and events copying some
uninitialized stack data to userspace
* tag 'wireless-2026-01-08' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mac80211: collect station statistics earlier when disconnect
wifi: mac80211: restore non-chanctx injection behaviour
wifi: mac80211_hwsim: disable BHs for hwsim_radio_lock
wifi: mac80211: don't iterate not running interfaces
wifi: mac80211_hwsim: fix typo in frequency notification
wifi: avoid kernel-infoleak from struct iw_point
====================
Jakub Kicinski [Tue, 6 Jan 2026 16:34:26 +0000 (08:34 -0800)]
tools: ynl: don't install tests
make's install target is meant for installing the production
artifacts, AFAIU. Don't install test_ynl_cli and test_ynl_ethtool
from under the main YNL install target. The install target
under tests/ is retained in case someone wants the tests
to be installed.
Fixes: 308b7dee3e5c ("tools: ynl: add YNL test framework") Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Link: https://patch.msgid.link/20260106163426.1468943-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
msg_get_inq is an input field from caller to callee. Don't set it in
the callee, as the caller may not clear it on struct reuse.
This is a kernel-internal variant of msghdr only, and the only user
does reinitialize the field. So this is not critical for that reason.
But it is more robust to avoid the write, and slightly simpler code.
And it fixes a bug, see below.
Callers set msg_get_inq to request the input queue length to be
returned in msg_inq. This is equivalent to but independent from the
SO_INQ request to return that same info as a cmsg (tp->recvmsg_inq).
To reduce branching in the hot path the second also sets the msg_inq.
That is WAI.
This is a fix to commit 4d1442979e4a ("af_unix: don't post cmsg for
SO_INQ unless explicitly asked for"), which fixed the inverse.
Also avoid NULL pointer dereference in unix_stream_read_generic if
state->msg is NULL and msg->msg_get_inq is written. A NULL state->msg
can happen when splicing as of commit 2b514574f7e8 ("net: af_unix:
implement splice for stream af_unix sockets").
Breno Leitao [Tue, 6 Jan 2026 14:31:14 +0000 (06:31 -0800)]
bnxt_en: Fix NULL pointer crash in bnxt_ptp_enable during error cleanup
When bnxt_init_one() fails during initialization (e.g.,
bnxt_init_int_mode returns -ENODEV), the error path calls
bnxt_free_hwrm_resources() which destroys the DMA pool and sets
bp->hwrm_dma_pool to NULL. Subsequently, bnxt_ptp_clear() is called,
which invokes ptp_clock_unregister().
Since commit a60fc3294a37 ("ptp: rework ptp_clock_unregister() to
disable events"), ptp_clock_unregister() now calls
ptp_disable_all_events(), which in turn invokes the driver's .enable()
callback (bnxt_ptp_enable()) to disable PTP events before completing the
unregistration.
bnxt_ptp_enable() attempts to send HWRM commands via bnxt_ptp_cfg_pin()
and bnxt_ptp_cfg_event(), both of which call hwrm_req_init(). This
function tries to allocate from bp->hwrm_dma_pool, causing a NULL
pointer dereference:
Xiang Mei [Tue, 6 Jan 2026 03:41:00 +0000 (20:41 -0700)]
net/sched: sch_qfq: Fix NULL deref when deactivating inactive aggregate in qfq_reset
`qfq_class->leaf_qdisc->q.qlen > 0` does not imply that the class
itself is active.
Two qfq_class objects may point to the same leaf_qdisc. This happens
when:
1. one QFQ qdisc is attached to the dev as the root qdisc, and
2. another QFQ qdisc is temporarily referenced (e.g., via qdisc_get()
/ qdisc_put()) and is pending to be destroyed, as in function
tc_new_tfilter.
When packets are enqueued through the root QFQ qdisc, the shared
leaf_qdisc->q.qlen increases. At the same time, the second QFQ
qdisc triggers qdisc_put and qdisc_destroy: the qdisc enters
qfq_reset() with its own q->q.qlen == 0, but its class's leaf
qdisc->q.qlen > 0. Therefore, the qfq_reset would wrongly deactivate
an inactive aggregate and trigger a null-deref in qfq_deactivate_agg:
Linus Torvalds [Thu, 8 Jan 2026 15:44:48 +0000 (07:44 -0800)]
Merge tag 'hid-for-linus-2026010801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- build fix for HID-BPF (Benjamin Tissoires)
- fix for potential buffer overflow in i2c-hid (Kwok Kin Ming)
- a couple of selftests/hid fixes (Peter Hutterer)
- fix for handling pressure pads in hid-multitouch (Peter Hutterer)
- fix for potential NULL pointer dereference in intel-thc-hid (Even Xu)
- fix for interrupt delay control in intel-thc-hid (Even Xu)
- fix finger release detection on some VTL-class touchpads (DaytonCL)
- fix for correct enumeration on intel-ish-hid systems with no sensors
(Zhang Lixu)
- assorted device ID additions and device-specific quirks
* tag 'hid-for-linus-2026010801' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (21 commits)
HID: logitech: add HID++ support for Logitech MX Anywhere 3S
HID: Elecom: Add support for ELECOM M-XT3DRBK (018C)
HID: quirks: work around VID/PID conflict for appledisplay
HID: Apply quirk HID_QUIRK_ALWAYS_POLL to Edifier QR30 (2d99:a101)
HID: i2c-hid: fix potential buffer overflow in i2c_hid_get_report()
selftests/hid: add a test for the Digitizer/Button Type pressurepad
selftests/hid: use a enum class for the different button types
selftests/hid: require hidtools 0.12
HID: multitouch: set INPUT_PROP_PRESSUREPAD based on Digitizer/Button Type
HID: quirks: Add another Chicony HP 5MP Cameras to hid_ignore_list
HID: Intel-thc-hid: Intel-thc: Add safety check for reading DMA buffer
hid: intel-thc-hid: Select SGL_ALLOC
selftests/hid: fix bpf compilations due to -fms-extensions
HID: bpf: fix bpf compilation with -fms-extensions
HID: Intel-thc-hid: Intel-thc: Fix wrong register reading
HID: multitouch: add MT_QUIRK_STICKY_FINGERS to MT_CLS_VTL
HID: intel-ish-hid: Reset enum_devices_done before enumeration
HID: intel-ish-hid: Update ishtp bus match to support device ID table
HID: Intel-thc-hid: Intel-thc: fix dma_unmap_sg() nents value
HID: playstation: Center initial joystick axes to prevent spurious events
...
If on any iteration in gpiod_find(), gpio_desc_table_match() returns
NULL (which is normal and expected), we never reinitialize desc back to
ERR_PTR(-ENOENT) and if we don't find a match later on, we will return
NULL causing a NULL-pointer dereference in users not expecting it. Don't
initialize desc, but return ERR_PTR(-ENOENT) explicitly at the end of
the function.
Fixes: 9700b0fccf38 ("gpiolib: allow multiple lookup tables per consumer") Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Closes: https://lore.kernel.org/all/00107523-7737-4b92-a785-14ce4e93b8cb@samsung.com/ Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20260108102314.18816-1-bartosz.golaszewski@oss.qualcomm.com Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Baochen Qiang [Mon, 22 Dec 2025 02:29:07 +0000 (10:29 +0800)]
wifi: mac80211: collect station statistics earlier when disconnect
In __sta_info_destroy_part2(), station statistics are requested after the
IEEE80211_STA_NONE -> IEEE80211_STA_NOTEXIST transition. This is
problematic because the driver may be unable to handle the request due to
the STA being in the NOTEXIST state (i.e. if the driver destroys the
underlying data when transitioning to NOTEXIST).
Move the statistics collection to before the state transition to avoid
this issue.
During the transition to use channel contexts throughout, the
ability to do injection while in monitor mode concurrent with
another interface was lost, since the (virtual) monitor won't
have a chanctx assigned in this scenario.
It's harder to fix drivers that actually transitioned to using
channel contexts themselves, such as mt76, but it's easy to do
those that are (still) just using the emulation. Do that.
Miri Korenblit [Wed, 7 Jan 2026 13:37:36 +0000 (14:37 +0100)]
wifi: mac80211: don't iterate not running interfaces
for_each_chanctx_user_* was introdcued as a replacement for
for_each_sdata_link, which visits also other chanctx users that are not
link.
for_each_sdata_link skips not running interfaces, do the same for
for_each_chanctx_user_*
Benjamin Berg [Wed, 7 Jan 2026 13:36:51 +0000 (14:36 +0100)]
wifi: mac80211_hwsim: fix typo in frequency notification
The NAN notification is for 5745 MHz which corresponds to channel 149
and not 5475 which is not actually a valid channel. This could result in
a NULL pointer dereference in cfg80211_next_nan_dw_notif.
Fixes: a37a6f54439b ("wifi: mac80211_hwsim: Add simulation support for NAN device") Signed-off-by: Benjamin Berg <benjamin.berg@intel.com> Reviewed-by: Ilan Peer <ilan.peer@intel.com> Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com> Link: https://patch.msgid.link/20260107143652.7dab2035836f.Iacbaf7bb94ed5c14a0928a625827e4137d8bfede@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Eric Dumazet [Thu, 8 Jan 2026 10:19:27 +0000 (10:19 +0000)]
wifi: avoid kernel-infoleak from struct iw_point
struct iw_point has a 32bit hole on 64bit arches.
struct iw_point {
void __user *pointer; /* Pointer to the data (in user space) */
__u16 length; /* number of fields or size in bytes */
__u16 flags; /* Optional params */
};
Make sure to zero the structure to avoid disclosing 32bits of kernel data
to user space.
Fixes: 87de87d5e47f ("wext: Dispatch and handle compat ioctls entirely in net/wireless/wext.c") Reported-by: syzbot+bfc7323743ca6dbcc3d3@syzkaller.appspotmail.com Closes: https://lore.kernel.org/netdev/695f83f3.050a0220.1c677c.0392.GAE@google.com/T/#u Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20260108101927.857582-1-edumazet@google.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HID: logitech: add HID++ support for Logitech MX Anywhere 3S
I've acquired a Logitech MX Anywhere 3S mouse, which supports HID++ over
Bluetooth. Adding its PID 0xb037 to the allowlist enables the additional
features, such as high-resolution scrolling. Tested working across multiple
machines, with a mix of Intel and Mediatek Bluetooth chips.
net: airoha: Fix schedule while atomic in airoha_ppe_deinit()
airoha_ppe_deinit() runs airoha_npu_ppe_deinit() in atomic context.
airoha_npu_ppe_deinit routine allocates ppe_data buffer with GFP_KERNEL
flag. Rely on rcu_replace_pointer in airoha_ppe_deinit routine in order
to fix schedule while atomic issue in airoha_npu_ppe_deinit() since we
do not need atomic context there.
HID: Elecom: Add support for ELECOM M-XT3DRBK (018C)
Wireless/new version of the Elecom trackball mouse M-XT3DRBK has a
product id that differs from the existing M-XT3DRBK.
The report descriptor format also seems to have changed and matches
other (newer?) models instead (except for six buttons instead of eight).
This patch follows the same format as the patch for the M-XT3URBK (018F)
by Naoki Ueki (Nov 3rd 2025) to enable the sixth mouse button.
dmesg output:
[ 292.074664] usb 1-2: new full-speed USB device number 7 using xhci_hcd
[ 292.218667] usb 1-2: New USB device found, idVendor=056e, idProduct=018c, bcdDevice= 1.00
[ 292.218676] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 292.218679] usb 1-2: Product: ELECOM TrackBall Mouse
[ 292.218681] usb 1-2: Manufacturer: ELECOM
René Rebe [Fri, 28 Nov 2025 12:46:41 +0000 (13:46 +0100)]
HID: quirks: work around VID/PID conflict for appledisplay
For years I wondered why the Apple Cinema Display driver would not
just work for me. Turns out the hidraw driver instantly takes it
over. Fix by adding appledisplay VID/PIDs to hid_have_special_driver.
Fixes: 069e8a65cd79 ("Driver for Apple Cinema Display") Signed-off-by: René Rebe <rene@exactco.de> Signed-off-by: Jiri Kosina <jkosina@suse.com>
Fixes: 2a6c826cfeed ("drm/amd: Skip power ungate during suspend for VPE") Signed-off-by: Mario Limonciello (AMD) <superm1@kernel.org> Acked-by: Alex Deucher <alexander.deucher@amd.com> Reported-by: Konstantin <answer2019@yandex.ru> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220812 Reported-by: Matthew Schwartz <matthew.schwartz@linux.dev> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3925683515e93844be204381d2d5a1df5de34f31)
Alex Hung [Mon, 8 Dec 2025 19:11:43 +0000 (12:11 -0700)]
drm/amd/display: Check NULL before calling dac_load_detection
dac_load_detection can be NULL in some scenario, so checking it before
calling.
Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Chenyu Chen <chen-yu.chen@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 179176134b535246f0b368b30e8ecad50066f896)
Perry Yuan [Thu, 25 Dec 2025 08:43:49 +0000 (16:43 +0800)]
drm/amd/pm: Disable MMIO access during SMU Mode 1 reset
During Mode 1 reset, the ASIC undergoes a reset cycle and becomes
temporarily inaccessible via PCIe. Any attempt to access MMIO registers
during this window (e.g., from interrupt handlers or other driver threads)
can result in uncompleted PCIe transactions, leading to NMI panics or
system hangs.
To prevent this, set the `no_hw_access` flag to true immediately after
triggering the reset. This signals other driver components to skip
register accesses while the device is offline.
A memory barrier `smp_mb()` is added to ensure the flag update is
globally visible to all cores before the driver enters the sleep/wait
state.
Signed-off-by: Perry Yuan <perry.yuan@amd.com> Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 7edb503fe4b6d67f47d8bb0dfafb8e699bb0f8a4)
Dave Airlie [Wed, 7 Jan 2026 21:34:36 +0000 (07:34 +1000)]
Merge tag 'exynos-drm-fixes-v6.19-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes
One code cleanup
. Replace system_wq with system_percpu_wq in the Exynos HDMI driver.
system_wq is effectively a per-cpu workqueue, but its name does not make
this explicit. Recent workqueue changes introduced system_percpu_wq to clarify
semantics and support ongoing workqueue API refactoring.
(Functions in sbi_ecall.c are excluded from tracing if
CONFIG_RISCV_ALTERNATIVE_EARLY is set.)
__sbi_ecall triggers a snapshot of the ringbuffer. The snapshot code
raises an IPI interrupt, which results in another call to __sbi_ecall
and another snapshot...
All it takes to get into this endless loop is one initial __sbi_ecall.
On RISC-V systems without SSTC extension, the clock events in
timer-riscv.c issue periodic sbi ecalls, making the problem easy to
trigger.
Always exclude the sbi_ecall.c functions from tracing to fix the
potential deadlock.
sbi ecalls can easiliy be logged via trace events, excluding ecall
functions from function tracing is not a big limitation.
Ilpo Järvinen [Mon, 24 Nov 2025 17:04:11 +0000 (19:04 +0200)]
sparc/PCI: Correct 64-bit non-pref -> pref BAR resources
SPARC T5-2 dts describes some PCI BARs as 64-bit resources without the
pref(etchable) bit (0x83... vs 0xc3... in assigned-addresses) for address
ranges above the 4G threshold. Such resources cannot be placed into a
non-prefetchable PCI bridge window that is capable only of 32-bit
addressing. As such, it looks like the platform is improperly described by
the dts.
The kernel detects this problem (see the IORESOURCE_PREFETCH check in
pci_find_parent_resource()) and fails to assign these BAR resources to the
resource tree due to lack of a compatible bridge window.
Prior to 754babaaf333 ("sparc/PCI: Remove pcibios_enable_device() as they
do nothing extra") SPARC arch code did not test whether device resources
were successfully in the resource tree when enabling a device, effectively
hiding the problem. After removing the arch-specific enable code,
pci_enable_resources() refuses to enable the device when it finds not all
mem resources are assigned, and therefore mpt3sas can't be enabled:
pci 0001:04:00.0: reg 0x14: [mem 0x801110000000-0x80111000ffff 64bit]
pci 0001:04:00.0: reg 0x1c: [mem 0x801110040000-0x80111007ffff 64bit]
pci 0001:04:00.0: BAR 1 [mem 0x801110000000-0x80111000ffff 64bit]: can't claim; no compatible bridge window
pci 0001:04:00.0: BAR 3 [mem 0x801110040000-0x80111007ffff 64bit]: can't claim; no compatible bridge window
mpt3sas 0001:04:00.0: BAR 1 [mem size 0x00010000 64bit]: not assigned; can't enable device
For clarity, this filtered log only shows failures for one mpt3sas device
but other devices fail similarly. In the reported case, the end result with
all the failures is an unbootable system.
Things appeared to "work" before 754babaaf333 ("sparc/PCI: Remove
pcibios_enable_device() as they do nothing extra") because the resource
tree is agnostic to whether PCI BAR resources are properly in the tree or
not. So as long as there was a parent resource (e.g. a root bus resource)
that contains the address range, the resource tree code just places
resource request underneath it without any consideration to the
intermediate BAR resource. While it worked, it's incorrect setup still.
Add an OF fixup to set the IORESOURCE_PREFETCH flag for a 64-bit PCI
resource that has the end address above 4G requiring placement into the
prefetchable window. Also log the issue.
Fixes: 754babaaf333 ("sparc/PCI: Remove pcibios_enable_device() as they do nothing extra") Reported-by: Nathaniel Roach <nroach44@gmail.com> Closes: https://github.com/sparclinux/issues/issues/22 Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Tested-by: Nathaniel Roach <nroach44@gmail.com> Link: https://patch.msgid.link/20251124170411.3709-1-ilpo.jarvinen@linux.intel.com
Yunhui Cui [Tue, 16 Dec 2025 01:47:19 +0000 (09:47 +0800)]
riscv: remove irqflags.h inclusion in asm/bitops.h
The arch/riscv/include/asm/bitops.h does not functionally require
including /linux/irqflags.h. Additionally, adding
arch/riscv/include/asm/percpu.h causes a circular inclusion:
kernel/bounds.c
->include/linux/log2.h
->include/linux/bitops.h
->arch/riscv/include/asm/bitops.h
->include/linux/irqflags.h
->include/linux/find.h
->return val ? __ffs(val) : size;
->arch/riscv/include/asm/bitops.h
The compilation log is as follows:
CC kernel/bounds.s
In file included from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./arch/riscv/include/asm/processor.h:55,
from ./arch/riscv/include/asm/thread_info.h:42,
from ./include/linux/thread_info.h:60,
from ./include/asm-generic/preempt.h:5,
from ./arch/riscv/include/generated/asm/preempt.h:1,
from ./include/linux/preempt.h:79,
from ./arch/riscv/include/asm/percpu.h:8,
from ./include/linux/irqflags.h:19,
from ./arch/riscv/include/asm/bitops.h:14,
from ./include/linux/bitops.h:68,
from ./include/linux/log2.h:12,
from kernel/bounds.c:13:
./include/linux/find.h: In function 'find_next_bit':
./include/linux/find.h:66:30: error: implicit declaration of function '__ffs' [-Wimplicit-function-declaration]
66 | return val ? __ffs(val) : size;
| ^~~~~
Ben Dooks [Fri, 2 Jan 2026 14:58:39 +0000 (14:58 +0000)]
riscv: cpu_ops_sbi: smp_processor_id() returns int, not unsigned int
The print in sbi_cpu_stop() assumes smp_processor_id() returns an
unsigned int, when it is actually an int. Fix the format string to
avoid mismatch type warnings in rht pr_crit().
Steven Rostedt [Tue, 6 Jan 2026 01:31:41 +0000 (20:31 -0500)]
tracing: Add recursion protection in kernel stack trace recording
A bug was reported about an infinite recursion caused by tracing the rcu
events with the kernel stack trace trigger enabled. The stack trace code
called back into RCU which then called the stack trace again.
Expand the ftrace recursion protection to add a set of bits to protect
events from recursion. Each bit represents the context that the event is
in (normal, softirq, interrupt and NMI).
Have the stack trace code use the interrupt context to protect against
recursion.
Note, the bug showed an issue in both the RCU code as well as the tracing
stacktrace code. This only handles the tracing stack trace side of the
bug. The RCU fix will be handled separately.
Link: https://lore.kernel.org/all/20260102122807.7025fc87@gandalf.local.home/ Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Boqun Feng <boqun.feng@gmail.com> Link: https://patch.msgid.link/20260105203141.515cd49f@gandalf.local.home Reported-by: Yao Kai <yaokai34@huawei.com> Tested-by: Yao Kai <yaokai34@huawei.com> Fixes: 5f5fa7ea89dc ("rcu: Don't use negative nesting depth in __rcu_read_unlock()") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Steven Rostedt [Fri, 2 Jan 2026 19:31:48 +0000 (14:31 -0500)]
ftrace: Make ftrace_graph_ent depth field signed
The code has integrity checks to make sure that depth never goes below
zero. But the depth field has recently been converted to unsigned long
from "int" (for alignment reasons). As unsigned long can never be less
than zero, the integrity checks no longer work.
Convert depth to long from unsigned long to allow the integrity checks to
work again.
Cc: stable@vger.kernel.org Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: pengdonglin <pengdonglin@xiaomi.com> Link: https://patch.msgid.link/20260102143148.251c2e16@gandalf.local.home Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/aS6kGi0maWBl-MjZ@stanley.mountain/ Fixes: f83ac7544fbf7 ("function_graph: Enable funcgraph-args and funcgraph-retaddr to work simultaneously") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Wupeng Ma [Sun, 28 Dec 2025 06:50:07 +0000 (14:50 +0800)]
ring-buffer: Avoid softlockup in ring_buffer_resize() during memory free
When user resize all trace ring buffer through file 'buffer_size_kb',
then in ring_buffer_resize(), kernel allocates buffer pages for each
cpu in a loop.
If the kernel preemption model is PREEMPT_NONE and there are many cpus
and there are many buffer pages to be freed, it may not give up cpu
for a long time and finally cause a softlockup.
To avoid it, call cond_resched() after each cpu buffer free as Commit f6bd2c92488c ("ring-buffer: Avoid softlockup in ring_buffer_resize()")
does.
Detailed call trace as follow:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 24-....: (14837 ticks this GP) idle=521c/1/0x4000000000000000 softirq=230597/230597 fqs=5329
rcu: (t=15004 jiffies g=26003221 q=211022 ncpus=96)
CPU: 24 UID: 0 PID: 11253 Comm: bash Kdump: loaded Tainted: G EL 6.18.2+ #278 NONE
pc : arch_local_irq_restore+0x8/0x20
arch_local_irq_restore+0x8/0x20 (P)
free_frozen_page_commit+0x28c/0x3b0
__free_frozen_pages+0x1c0/0x678
___free_pages+0xc0/0xe0
free_pages+0x3c/0x50
ring_buffer_resize.part.0+0x6a8/0x880
ring_buffer_resize+0x3c/0x58
__tracing_resize_ring_buffer.part.0+0x34/0xd8
tracing_resize_ring_buffer+0x8c/0xd0
tracing_entries_write+0x74/0xd8
vfs_write+0xcc/0x288
ksys_write+0x74/0x118
__arm64_sys_write+0x24/0x38
Cc: <mathieu.desnoyers@efficios.com> Link: https://patch.msgid.link/20251228065008.2396573-1-mawupeng1@huawei.com Signed-off-by: Wupeng Ma <mawupeng1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
projects / thirdparty / kernel / linux.git / log
