This wireless mouse receiver needs a reset-resume quirk to properly come
out of reset.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1165206 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If SERIAL_8250 is compiled as a module, the platform specific setup
for Loongson will be a module too, and it will not work very well.
At least on Loongson 3 it will trigger a build failure,
since loongson_sysconf is not exported to modules.
Fix by making the platform specific serial code always built-in.
AMD/ATI HDMI controller chip models, we already have a filter to lower
to 32bit DMA, but the rest are supposed to be working with 64bit
although the hardware doesn't really work with 63bit but only with 40
or 48bit DMA. In this patch, we take 40bit DMA for safety for the
AMD/ATI controllers as the graphics drivers does.
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[lizf: Backported to 3.4:
- adjust context
- s/AZX_GCAP_640K/ICH6_GCAP_64OK] Signed-off-by: Zefan Li <lizefan@huawei.com>
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b44 ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Suggested-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message] Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4:
- adjust context
- drop changes to xhci_plat_suspend()] Signed-off-by: Zefan Li <lizefan@huawei.com>
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.) Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
A halted endpoint ring must first be reset, then move the ring
dequeue pointer past the problematic TRB. If we start the ring too
early after reset, but before moving the dequeue pointer we
will end up executing the same problematic TRB again.
As we always issue a set transfer dequeue command after a reset
endpoint command we can skip starting endpoint rings at reset endpoint
command completion.
Without this fix we end up trying to handle the same faulty TD for
contol endpoints. causing timeout, and failing testusb ctrl_out write
tests.
Fixes: e9df17e (USB: xhci: Correct assumptions about number of rings per endpoint.) Tested-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
According to the manuals I have, XScale auxiliary register should be
reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init
correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and
cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to
also use c1, c0, 1.
The issue was primarily noticed thanks to qemu reporing "unsupported
instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255
XScale Core manuals and in PXA270 and PXA320 Developers Guides.
Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board.
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
In some cases, the fcoe_rx_list may contains multiple instances
of the same skb (the so called "shared skbs").
the bnx2fc_l2_rcv thread is a loop that extracts a skb from the list,
modifies (and destroys) its content and then proceed to the next one.
The problem is that if the skb is shared, the remaining instances will
be corrupted.
The solution is to use skb_share_check() before adding the skb to the
fcoe_rx_list.
This patch breaks the race condition by adding a retest of the bit
after the call to rpc_sleep_on().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Both xprt_lookup_rqst() and xprt_complete_rqst() require that you
take the transport lock in order to avoid races with xprt_transmit().
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Reviewed-by: Jeff Layton <jlayton@primarydata.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Fix reporting of overrun errors, which should only be reported once
using the inserted null character.
Fixes: 6b8f1ca5581b ("USB: ssu100: set tty_flags in ssu100_process_packet") Signed-off-by: Johan Hovold <johan@kernel.org>
[lizf: Backported to 3.4:
- adjust context
- lookup tty using tty_port_tty_get()] Signed-off-by: Zefan Li <lizefan@huawei.com>
Fix handling of TTY error flags, which are not bitmasks and must
specifically not be ORed together as this prevents the line discipline
from recognising them.
Also insert null characters when reporting overrun errors as these are
not associated with the received character.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Johan Hovold <johan@kernel.org>
[lizf: Backported to 3.4:
- s/&port->port/tty/
- adjust context
- adjust indentation] Signed-off-by: Zefan Li <lizefan@huawei.com>
An IOCTL call that calls spi_setup() and then dw_spi_setup() will
overwrite the persisted last transfer speed. On each transfer, the
SPI speed is compared to the last transfer speed to determine if the
clock divider registers need to be updated (did the speed change?).
This bug was observed with the spidev driver using spi-config to
update the max transfer speed.
This fix: Don't overwrite the persisted last transaction clock speed
when updating the SPI parameters in dw_spi_setup(). On the next
transaction, the new speed won't match the persisted last speed
and the hardware registers will be updated.
On initialization, the persisted last transaction clock
speed will be 0 but will be updated after the first SPI
transaction.
Move zeroed clock divider check into clock change test because
chip->clk_div is zero on startup and would cause a divide-by-zero
error. The calculation was wrong as well (can't support odd #).
Reported-by: Vlastimil Setka <setka@vsis.cz> Signed-off-by: Vlastimil Setka <setka@vsis.cz> Signed-off-by: Thor Thayer <tthayer@opensource.altera.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway. Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Fixes: 916e4cf46d02 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data") Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: For 3.2, net/ipv6/output_core.c is a completely new file] Signed-off-by: Zefan Li <lizefan@huawei.com>
With commits 73f156a6e8c1 ("inetpeer: get rid of ip_id_count") and 04ca6973f7c1 ("ip: make IP identifiers less predictable"), IP
identifiers are generated from a counter chosen from an array of
counters indexed by the hash of the outgoing packet header's source
address, destination address, and protocol number. Thus, in
__ip_make_skb(), we must now call ip_select_ident() only after setting
these fields in the IP header to prevent IP identifiers from being
generated from bogus counters.
IP id sequence before fix: 18174, 5789, 5953, 59420, 59637, ...
After fix: 5967, 6185, 6374, 6600, 6795, 6892, 7051, 7288, ...
Signed-off-by: Jeffrey Knockel <jeffk@cs.unm.edu> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Cc: Eric Dumazet <edumazet@google.com>
[Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit d1442d85cc30 ("KVM: x86: Handle errors when RIP is set during far
jumps") introduced a bug that caused the fix to be incomplete. Due to
incorrect evaluation, far jump to segment with L bit cleared (i.e., 32-bit
segment) and RIP with any of the high bits set (i.e, RIP[63:32] != 0) set may
not trigger #GP. As we know, this imposes a security problem.
In addition, the condition for two warnings was incorrect.
Fixes: d1442d85cc30ea75f7d399474ca738e0bc96f715 Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
[Add #ifdef CONFIG_X86_64 to avoid complaints of undefined behavior. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Strictly speaking, this code was never correct. It should have set
read_exec_only and seg_not_present to 1 to indicate that it wanted
to find a free slot without putting anything there, or it should
have put something sensible in the TLS slot if it wanted to allocate
a TLS entry for real. The actual effect of this code was to
allocate a bogus segment that could be used to exploit espfix.
The set_thread_area hardening patches changed the behavior, causing
set_thread_area to return -EINVAL and crashing the game.
This changes set_thread_area to interpret this as a request to find
a free slot and to leave it empty, which isn't *quite* what the game
expects but should be close enough to keep it working. In
particular, using the code above to allocate two segments will
allocate the same segment both times.
According to FrostbittenKing on Github, this fixes The Witcher 2.
If this somehow still causes problems, we could instead allocate
a limit==0 32-bit data segment, but that seems rather ugly to me.
32-bit programs don't have an lm bit in their ABI, so they can't
reliably cause LDT_empty to return true without resorting to memset.
They shouldn't need to do this.
This should fix a longstanding, if minor, issue in all 64-bit kernels
as well as a potential regression in the TLS hardening code.
- Disables the F00F bug workaround warning. There is no F00F bug
workaround any more because Linux's standard IDT handling already
works around the F00F bug, but the warning still exists. This
is only cosmetic, and, in any event, there is no such thing as
KVM on a CPU with the F00F bug.
- Disables 32-bit APM BIOS detection. On a KVM paravirt system,
there should be no APM BIOS anyway.
- Disables tboot. I think that the tboot code should check the
CPUID hypervisor bit directly if it matters.
- paravirt_enabled disables espfix32. espfix32 should *not* be
disabled under KVM paravirt.
The last point is the purpose of this patch. It fixes a leak of the
high 16 bits of the kernel stack address on 32-bit KVM paravirt
guests. Fixes CVE-2014-8134.
Suggested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The WARN_ON checking whether i_mutex is held in
pagecache_isize_extended() was wrong because some filesystems (e.g.
XFS) use different locks for serialization of truncates / writes. So
just remove the check.
Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Found by the UC-KLEE tool: A user could supply less input to
firewire-cdev ioctls than write- or write/read-type ioctl handlers
expect. The handlers used data from uninitialized kernel stack then.
This could partially leak back to the user if the kernel subsequently
generated fw_cdev_event_'s (to be read from the firewire-cdev fd)
which notably would contain the _u64 closure field which many of the
ioctl argument structures contain.
The fact that the handlers would act on random garbage input is a
lesser issue since all handlers must check their input anyway.
The fix simply always null-initializes the entire ioctl argument buffer
regardless of the actual length of expected user input. That is, a
runtime overhead of memset(..., 40) is added to each firewirew-cdev
ioctl() call. [Comment from Clemens Ladisch: This part of the stack is
most likely to be already in the cache.]
Remarks:
- There was never any leak from kernel stack to the ioctl output
buffer itself. IOW, it was not possible to read kernel stack by a
read-type or write/read-type ioctl alone; the leak could at most
happen in combination with read()ing subsequent event data.
- The actual expected minimum user input of each ioctl from
include/uapi/linux/firewire-cdev.h is, in bytes:
[0x00] = 32, [0x05] = 4, [0x0a] = 16, [0x0f] = 20, [0x14] = 16,
[0x01] = 36, [0x06] = 20, [0x0b] = 4, [0x10] = 20, [0x15] = 20,
[0x02] = 20, [0x07] = 4, [0x0c] = 0, [0x11] = 0, [0x16] = 8,
[0x03] = 4, [0x08] = 24, [0x0d] = 20, [0x12] = 36, [0x17] = 12,
[0x04] = 20, [0x09] = 24, [0x0e] = 4, [0x13] = 40, [0x18] = 4.
Reported-by: David Ramos <daramos@stanford.edu> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
It's possible for iretq to userspace to fail. This can happen because
of a bad CS, SS, or RIP.
Historically, we've handled it by fixing up an exception from iretq to
land at bad_iret, which pretends that the failed iret frame was really
the hardware part of #GP(0) from userspace. To make this work, there's
an extra fixup to fudge the gs base into a usable state.
This is suboptimal because it loses the original exception. It's also
buggy because there's no guarantee that we were on the kernel stack to
begin with. For example, if the failing iret happened on return from an
NMI, then we'll end up executing general_protection on the NMI stack.
This is bad for several reasons, the most immediate of which is that
general_protection, as a non-paranoid idtentry, will try to deliver
signals and/or schedule from the wrong stack.
This patch throws out bad_iret entirely. As a replacement, it augments
the existing swapgs fudge into a full-blown iret fixup, mostly written
in C. It's should be clearer and more correct.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2:
- We didn't use the _ASM_EXTABLE macro
- Don't use __visible] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
There's nothing special enough about the espfix64 double fault fixup to
justify writing it in assembly. Move it to C.
This also fixes a bug: if the double fault came from an IST stack, the
old asm code would return to a partially uninitialized stack frame.
Fixes: 3891a04aafd668686239349ea58f3314ea2af86b Signed-off-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2:
- Keep using the paranoiderrorentry macro to generate the asm code
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
On a 32-bit kernel, this has no effect, since there are no IST stacks.
On a 64-bit kernel, #SS can only happen in user code, on a failed iret
to user space, a canonical violation on access via RSP or RBP, or a
genuine stack segment violation in 32-bit kernel code. The first two
cases don't need IST, and the latter two cases are unlikely fatal bugs,
and promoting them to double faults would be fine.
This fixes a bug in which the espfix64 code mishandles a stack segment
violation.
This saves 4k of memory per CPU and a tiny bit of code.
Signed-off-by: Andy Lutomirski <luto@amacapital.net> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[bwh: Backported to 3.2:
- No need to define trace_stack_segment
- Use the errorentry macro to generate #SS asm code
- Adjust context
- Checked that this matches Luis's backport for Ubuntu] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
We have a historical hack that treats missing ranges properties as the
equivalent of an empty one. This is needed for ancient PowerMac "bad"
device-trees, and shouldn't be enabled for any other PowerPC platform,
otherwise we get some nasty layout of devices in sysfs or even
duplication when a set of otherwise identically named devices is
created multiple times under a different parent node with no ranges
property.
This fix is needed for the PowerNV i2c busses to be exposed properly
and will fix a number of other embedded cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Grant Likely <grant.likely@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
This patch replaces the kfree_skb() by dev_kfree_skb_any().
Signed-off-by: Thomas Körper <thomas.koerper@esd.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
__setup() is designed to match options that take arguments, like
"foo=bar" where you would have:
__setup("foo", x86_foo_func...);
The problem is that "noxsave" actually _matches_ "noxsaves" in
the same way that "foo" matches "foo=bar". If you boot an old
kernel that does not know about "noxsaves" with "noxsaves" on the
command line, it will interpret the argument as "noxsave", which
is not what you want at all.
This makes the "noxsave" handler only return success when it finds
an *exact* match.
[ tglx: We really need to make __setup() more robust. ]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Dave Hansen <dave@sr71.net> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: x86@kernel.org Link: http://lkml.kernel.org/r/20141111220133.FE053984@viggo.jf.intel.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
Panic happened because we eat 4 bytes of skb headroom on each
(re)transmission when sending frame without the payload and the header
length not being multiple of 4 (i.e. QoS header has 26 bytes). On such
case because paylad_aling=2 is bigger than header_align=0 we increase
header_align by 4 bytes. To prevent that we could change the check to:
if (payload_length && payload_align > header_align)
header_align += 4;
but not aligning payload at all is more effective and alignment is not
really needed by H/W (that has been tested on OpenWrt project for few
years now).
Reported-and-tested-by: Antti S. Lankila <alankila@bel.fi> Debugged-by: Antti S. Lankila <alankila@bel.fi> Reported-by: Henrik Asp <solenskiner@gmail.com>
Originally-From: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
FSI doesn't support PAUSE.
Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
It is not guaranteed to that srp_sq_size is supported
by the HCA. So if we failed to create the QP with ENOMEM,
try with a smaller srp_sq_size. Keep it up until we hit
MIN_SRPT_SQ_SIZE, then fail the connection.
Reported-by: Mark Lehrer <lehrer@gmail.com> Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Large (greater than 32k, the value of PAGE_ALLOC_COSTLY_ORDER) auth
tickets will have their buffers vmalloc'ed, which leads to the
following crash in crypto:
NFSv4.0 does not have TEST_STATEID/FREE_STATEID functionality, so
unlike NFSv4.1, the recovery procedure when stateids have expired or
have been revoked requires us to just forget the delegation.
http://lkml.kernel.org/r/CAN-5tyHwG=Cn2Q9KsHWadewjpTTy_K26ee+UnSvHvG4192p-Xw@mail.gmail.com Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Variable 'err' needn't be initialized when nfs_getattr() uses it to
check whether it should call generic_fillattr() or not. That can result
in spurious error returns. Initialize 'err' properly.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Audit rules disappear when an inode they watch is evicted from the cache.
This is likely not what we want.
The guilty commit is "fsnotify: allow marks to not pin inodes in core",
which didn't take into account that audit_tree adds watches with a zero
mask.
Adding any mask should fix this.
Fixes: 90b1e7a57880 ("fsnotify: allow marks to not pin inodes in core") Signed-off-by: Miklos Szeredi <mszeredi@suse.cz> Signed-off-by: Paul Moore <pmoore@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Setups that use the blk-mq I/O path can lock up if a host with a single
device that has its door locked enters EH. Make sure to only send the
command to re-lock the door to devices that actually were reset and thus
might have lost their state. Otherwise the EH code might be get blocked
on blk_get_request as all requests for non-reset devices might be in use.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reported-by: Meelis Roos <meelis.roos@ut.ee> Tested-by: Meelis Roos <meelis.roos@ut.ee> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
On some Dell Latitude laptops ALPS device or Dell EC send one invalid byte
in 6 bytes ALPS packet. In this case psmouse driver enter out of sync
state. It looks like that all other bytes in packets are valid and also
device working properly. So there is no need to do full device reset, just
need to wait for byte which match condition for first byte (start of
packet). Because ALPS packets are bigger (6 or 8 bytes) default limit is
small.
This patch increase number of invalid bytes to size of 2 ALPS packets which
psmouse driver can drop before do full reset.
Resetting ALPS devices take some time and when doing reset on some Dell
laptops touchpad, trackstick and also keyboard do not respond. So it is
better to do it only if really necessary.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Tested-by: Pali Rohár <pali.rohar@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
5th and 6th byte of ALPS trackstick V3 protocol match condition for first
byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS
trackstick is sending data then driver match 5th, 6th and next 1st bytes as
PS/2.
It basically means if user is using trackstick when driver is in out of
sync state driver will never resync. Processing these bytes as 3 bytes PS/2
data cause total mess (random cursor movements, random clicks) and make
trackstick unusable until psmouse driver decide to do full device reset.
Lot of users reported problems with ALPS devices on Dell Latitude E6440,
E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send
some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like
that i8042 and psmouse/alps driver always receive group of 6 bytes packets
so there are no missing bytes and no bytes were inserted between valid
ones.
This patch does not fix root of problem with ALPS devices found in Dell
Latitude laptops but it does not allow to process some (invalid)
subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of
sync.
So with this patch trackstick input device does not report bogus data when
also driver is out of sync, so trackstick should be usable on those
machines.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com> Tested-by: Pali Rohár <pali.rohar@gmail.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
When VLAN is in use in macvtap_put_user, we end up setting
csum_start to the wrong place. The result is that the whoever
ends up doing the checksum setting will corrupt the packet instead
of writing the checksum to the expected location, usually this
means writing the checksum with an offset of -4.
This patch fixes this by adjusting csum_start when VLAN tags are
detected.
Fixes: f09e2249c4f5 ("macvtap: restore vlan header on user read") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Cheers, Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Upon receiving the last fragment, all but the first fragment
are freed, but the multicast check for statistics at the end
of the function refers to the current skb (the last fragment)
causing a use-after-free bug.
Since multicast frames cannot be fragmented and we check for
this early in the function, just modify that check to also
do the accounting to fix the issue.
Reported-by: Yosef Khyal <yosefx.khyal@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Priority of a merged request is computed by ioprio_best(). If one of the
requests has undefined priority (IOPRIO_CLASS_NONE) and another request
has priority from IOPRIO_CLASS_BE, the function will return the
undefined priority which is wrong. Fix the function to properly return
priority of a request with the defined priority.
Fixes: d58cdfb89ce0c6bd5f81ae931a984ef298dbda20 Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
[lizf: Backported to 3.4: adjust filename] Signed-off-by: Zefan Li <lizefan@huawei.com>
When an interface is deleted, an ongoing hardware scan is canceled and
the driver must abort the scan, at the very least reporting completion
while the interface is removed.
However, if it scheduled the work that might only run after everything
is said and done, which leads to cfg80211 warning that the scan isn't
reported as finished yet; this is no fault of the driver, it already
did, but mac80211 hasn't processed it.
To fix this situation, flush the delayed work when the interface being
removed is the one that was executing the scan.
Reported-by: Sujith Manoharan <sujith@msujith.org> Tested-by: Sujith Manoharan <sujith@msujith.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[lizf: Backported to 3.4: rcu_access_pointer() isn't used] Signed-off-by: Zefan Li <lizefan@huawei.com>
The dm-raid superblock (struct dm_raid_superblock) is padded to 512
bytes and that size is being used to read it in from the metadata
device into one preallocated page.
Reading or writing this on a 512-byte sector device works fine but on
a 4096-byte sector device this fails.
Set the dm-raid superblock's size to the logical block size of the
metadata device, because IO at that size is guaranteed too work. Also
add a size check to avoid silent partial metadata loss in case the
superblock should ever grow past the logical block size or PAGE_SIZE.
[includes pointer math fix from Dan Carpenter] Reported-by: "Liuhua Wang" <lwang@suse.com> Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Userspace actually passes single parameter (path name) to the umount
syscall, so new umount just fails. Fix it by requesting old umount
syscall implementation and re-wiring umount to it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
[lizf: Backported to 3.4: adjust filename] Signed-off-by: Zefan Li <lizefan@huawei.com>
The shrinker uses gfp flags to indicate what kind of operation can the
driver wait for. If __GFP_IO flag is present, the driver can wait for
block I/O operations, if __GFP_FS flag is present, the driver can wait on
operations involving the filesystem.
dm-bufio tested for __GFP_IO. However, dm-bufio can run on a loop block
device that makes calls into the filesystem. If __GFP_IO is present and
__GFP_FS isn't, dm-bufio could still block on filesystem operations if it
runs on a loop block device.
The change from __GFP_IO to __GFP_FS supposedly fixes one observed (though
unreproducible) deadlock involving dm-bufio and loop device.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[lizf: Backported to 3.4:
- drop changes to dm_bufio_shrink_scan() and dm_bufio_shrink_count()
- change __GFP_IO to __GFP_FS in shrink()] Signed-off-by: Zefan Li <lizefan@huawei.com>
There is a race condition when removing glue directory.
It can be reproduced in following test:
path 1: Add first child device
device_add()
get_device_parent()
/*find parent from glue_dirs.list*/
list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry)
if (k->parent == parent_kobj) {
kobj = kobject_get(k);
break;
}
....
class_dir_create_and_add()
path2: Remove last child device under glue dir
device_del()
cleanup_device_parent()
cleanup_glue_dir()
kobject_put(glue_dir);
If path2 has been called cleanup_glue_dir(), but not
call kobject_put(glue_dir), the glue dir is still
in parent's kset list. Meanwhile, path1 find the glue
dir from the glue_dirs.list. Path2 may release glue dir
before path1 call kobject_get(). So kernel will report
the warning and bug_on.
This is a "classic" problem we have of a kref in a list
that can be found while the last instance could be removed
at the same time.
This patch reuse gdp_mutex to fix this race condition.
The following calltrace is captured in kernel 3.4, but
the latest kernel still has this bug.
We can call this function for a dummy console that doesn't support
setting the font mapping, which will result in a null ptr BUG. So check
for this case and return error for consoles w/o font mapping support.
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=59321 Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: just return -EINVAL as we don't need to unlock] Signed-off-by: Zefan Li <lizefan@huawei.com>
Kernel oops can cause the tty to be unreleaseable (for example, if
n_tty_read() crashes while on the read_wait queue). This will cause
tty_release() to endlessly loop without sleeping.
Use a killable sleep timeout which grows by 2n+1 jiffies over the interval
[0, 120 secs.) and then jumps to forever (but still killable).
NB: killable just allows for the task to be rewoken manually, not
to be terminated.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
uart_get_baud_rate() will return baud == 0 if the max rate is set
to the "magic" 38400 rate and the SPD_* flags are also specified.
On the first iteration, if the current baud rate is higher than the
max, the baud rate is clamped at the max (which in the degenerate
case is 38400). On the second iteration, the now-"magic" 38400 baud
rate selects the possibly higher alternate baud rate indicated by
the SPD_* flag. Since only two loop iterations are performed, the
loop is exited, a kernel WARNING is generated and a baud rate of
0 is returned.
Only perform the "magic" 38400 -> SPD_* baud transform on the first
loop iteration, which prevents the degenerate case from recognizing
the clamped baud rate as the "magic" 38400 value.
Reported-by: Robert Święcki <robert@swiecki.net> Signed-off-by: Peter Hurley <peter@hurleysoftware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
We should check if a channel is enabled, not if no channels are enabled.
Fixes: 550268ca1111 ("staging:iio: scrap scan_count and ensure all drivers use active_scan_mask") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
This comes from the fact that usb-audio driver may receive the
disconnect callback multiple times, per each usb interface. When a
device has both audio and midi interfaces, it gets called twice, and
currently the driver tries to release resources at the last call.
At this point, the first parent interface has been already deleted,
thus deleting a child of the first parent hits such a warning.
For fixing this problem, we need to call snd_card_disconnect() and
cancel pending operations at the very first disconnect while the
release of the whole objects waits until the last disconnect call.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80931 Reported-and-tested-by: Tomas Gayoso <tgayoso@gmail.com> Reported-and-tested-by: Chris J Arges <chris.j.arges@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
If we hit any errors in btrfs_lookup_csums_range, we'll loop through all
the csums we allocate and free them. But the code was using list_entry
incorrectly, and ended up trying to free the on-stack list_head instead.
The string property read helpers will run off the end of the buffer if
it is handed a malformed string property. Rework the parsers to make
sure that doesn't happen. At the same time add new test cases to make
sure the functions behave themselves.
The original implementations of of_property_read_string_index() and
of_property_count_strings() both open-coded the same block of parsing
code, each with it's own subtly different bugs. The fix here merges
functions into a single helper and makes the original functions static
inline wrappers around the helper.
One non-bugfix aspect of this patch is the addition of a new wrapper,
of_property_read_string_array(). The new wrapper is needed by the
device_properties feature that Rafael is working on and planning to
merge for v3.19. The implementation is identical both with and without
the new static inline wrapper, so it just got left in to reduce the
churn on the header file.
Signed-off-by: Grant Likely <grant.likely@linaro.org> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Darren Hart <darren.hart@intel.com>
[lizf: Backported to 3.4:
- adjust context
- drop selftest hunks that don't apply] Signed-off-by: Zefan Li <lizefan@huawei.com>
The switch back is limited to ULT even on HP. The contrary
finding arose by bad luck in BIOS versions for testing.
This fixes spontaneous resume from S3 on some HP laptops.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Currently this quirk is enabled for the model with the device id 0x0089, it
is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904
as well.
Add new quirk for devices that cannot handle requests for the
device_qualifier descriptor.
A USB-2.0 compliant device must respond to requests for the
device_qualifier descriptor (even if it's with a request error), but at
least one device is known to misbehave after such a request.
Suggested-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Tested-by: Paul Osmialowski <newchief@king.net.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[lizf: Backported to 3.4: change usb_stor_dbg() to US_DEBUGP()] Signed-off-by: Zefan Li <lizefan@huawei.com>
[10238.622067] scsi host3: uas_eh_bus_reset_handler start
[10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10245.779365] usb 3-4: device descriptor read/8, error -110
[10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd
[10250.897603] usb 3-4: device descriptor read/8, error -110
[10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
[10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140
<snip>
[10251.059473] Call Trace:
[10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130
[10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0
[10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0
[10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100
[10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70
[10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0
[10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas]
[10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas]
[10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0
[10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas]
[10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110
[10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270
<snip>
The problem is the following call sequence (simplified):
1) usb_reset_device
2) usb_reset_and_verify_device
2) hub_port_init
3) hub_port_finish_reset
3) xhci_discover_or_reset_device
This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0
4) usb_get_device_descriptor
This fails
5) hub_port_init fails
6) usb_reset_and_verify_device fails, does not restore device config
7) uas_post_reset
8) xhci_alloc_streams
NULL deref on the free-ed ring
This commit fixes this by not allowing usb_alloc_streams to continue if
the device is not configured.
Note that we do allow usb_free_streams to continue after a (logical)
disconnect, as it is necessary to explicitly free the streams at the xhci
controller level.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Back in 7230c5644188 ("powerpc: Rework lazy-interrupt handling") we
added a call out to restore_interrupts() (written in c) before calling
do_notify_resume:
Unfortunately do_notify_resume takes two arguments, the second one
being the thread_info flags:
void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags)
We do populate r4 (the second argument) earlier, but
restore_interrupts() is free to muck it up all it wants. My guess is
the gcc compiler gods shone down on us and its register allocator
never used r4. Sometimes, rarely, luck is on our side.
LLVM on the other hand did trample r4.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The acpi-video backlight interface on the Acer KAV80 is broken, and worse
it causes the entire machine to slow down significantly after a suspend/resume.
Blacklist it, and use the acer-wmi backlight interface instead. Note that
the KAV80 is somewhat unique in that it is the only Acer model where we
fall back to acer-wmi after blacklisting, rather then using the native
(e.g. intel) backlight driver. This is done because there is no native
backlight interface on this model.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1128309 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The acpi-video backlight interface on the NC210 does not work, blacklist it
and use the samsung-laptop interface instead.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=861573 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Darren Hart <dvhart@linux.intel.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
When ext4_handle_dirty_dx_node() or ext4_handle_dirty_dirent_node()
fail, there's really something wrong with the fs and there's no point in
continuing further. Just return error from make_indexed_dir() in that
case. Also initialize frames array so that if we return early due to
error, dx_release() doesn't try to dereference uninitialized memory
(which could happen also due to error in do_split()).
Coverity-id: 741300 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu>
[lizf: Backported to 3.4:
- adjust context
- replace ext4_handle_dirty_{dx,dirent}_node() with
ext4_handle_dirty_metadata()] Signed-off-by: Zefan Li <lizefan@huawei.com>
ARM has some private syscalls (for example, set_tls(2)) which lie
outside the range of NR_syscalls. If any of these are called while
syscall tracing is being performed, out-of-bounds array access will
occur in the ftrace and perf sys_{enter,exit} handlers.
# trace-cmd record -e syscalls:* true
[ 17.289329] Unable to handle kernel paging request at virtual address aaaaaace
[ 17.289590] pgd = 9e71c000
[ 17.289696] [aaaaaace] *pgd=00000000
[ 17.289985] Internal error: Oops: 5 [#1] PREEMPT SMP ARM
[ 17.290169] Modules linked in:
[ 17.290391] CPU: 0 PID: 704 Comm: true Not tainted 3.18.0-rc2+ #21
[ 17.290585] task: 9f4dab00 ti: 9e710000 task.ti: 9e710000
[ 17.290747] PC is at ftrace_syscall_enter+0x48/0x1f8
[ 17.290866] LR is at syscall_trace_enter+0x124/0x184
Fix this by ignoring out-of-NR_syscalls-bounds syscall numbers.
Commit cd0980fc8add "tracing: Check invalid syscall nr while tracing syscalls"
added the check for less than zero, but it should have also checked
for greater than NR_syscalls.
Link: http://lkml.kernel.org/p/1414620418-29472-1-git-send-email-rabin@rab.in Fixes: cd0980fc8add "tracing: Check invalid syscall nr while tracing syscalls" Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
When screen objects are enabled, the bpp is assumed to be 32, otherwise
it is set to 16.
v2:
* Use u32 instead of u64 for assumed_bpp.
* Fixed mechanism to check for screen objects
* Limit the back buffer size to VRAM.
Signed-off-by: Sinclair Yeh <syeh@vmware.com> Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
[lizf: Backported to 3.4: drop the changes to vmw_driver_load()] Signed-off-by: Zefan Li <lizefan@huawei.com>
When we fail to load block bitmap in __ext4_new_inode() we will
dereference NULL pointer in ext4_journal_get_write_access(). So check
for error from ext4_read_block_bitmap().
Coverity-id: 989065 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Zefan Li <lizefan@huawei.com>
When there are no meta block groups update_backups() will compute the
backup block in 32-bit arithmetics thus possibly overflowing the block
number and corrupting the filesystem. OTOH filesystems without meta
block groups larger than 16 TB should be rare. Fix the problem by doing
the counting in 64-bit arithmetics.
Coverity-id: 741252 Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Lukas Czerner <lczerner@redhat.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
If __bitmap_shift_left() or __bitmap_shift_right() are asked to shift by
a multiple of BITS_PER_LONG, they will try to shift a long value by
BITS_PER_LONG bits which is undefined. Change the functions to avoid
the undefined shift.
Coverity id: 1192175
Coverity id: 1192174 Signed-off-by: Jan Kara <jack@suse.cz> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If an anonymous mapping is not allowed to fault thp memory and then
madvise(MADV_HUGEPAGE) is used after fault, khugepaged will never
collapse this memory into thp memory.
This occurs because the madvise(2) handler for thp, hugepage_madvise(),
clears VM_NOHUGEPAGE on the stack and it isn't stored in vma->vm_flags
until the final action of madvise_behavior(). This causes the
khugepaged_enter_vma_merge() to be a no-op in hugepage_madvise() when
the vma had previously had VM_NOHUGEPAGE set.
Fix this by passing the correct vma flags to the khugepaged mm slot
handler. There's no chance khugepaged can run on this vma until after
madvise_behavior() returns since we hold mm->mmap_sem.
It would be possible to clear VM_NOHUGEPAGE directly from vma->vm_flags
in hugepage_advise(), but I didn't want to introduce special case
behavior into madvise_behavior(). I think it's best to just let it
always set vma->vm_flags itself.
Signed-off-by: David Rientjes <rientjes@google.com> Reported-by: Suleiman Souhlal <suleiman@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit ff7ee93f4715 ("cgroup/kmemleak: Annotate alloc_page() for cgroup
allocations") introduces kmemleak_alloc() for alloc_page_cgroup(), but
corresponding kmemleak_free() is missing, which makes kmemleak be
wrongly disabled after memory offlining. Log is pasted at the end of
this commit message.
This patch add kmemleak_free() into free_page_cgroup(). During page
offlining, this patch removes corresponding entries in kmemleak rbtree.
After that, the freed memory can be allocated again by other subsystems
without killing kmemleak.
bash # for x in 1 2 3 4; do echo offline > /sys/devices/system/memory/memory$x/state ; sleep 1; done ; dmesg | grep leak
Fixes: ff7ee93f4715 (cgroup/kmemleak: Annotate alloc_page() for cgroup allocations) Signed-off-by: Wang Nan <wangnan0@huawei.com> Acked-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Michal Hocko <mhocko@suse.cz> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
When unmapping a range of pages in zap_pte_range, the page being
unmapped is added to an mmu_gather_batch structure for asynchronous
freeing. If we run out of space in the batch structure before the range
has been completely unmapped, then we break out of the loop, force a
TLB flush and free the pages that we have batched so far. If there are
further pages to unmap, then we resume the loop where we left off.
Unfortunately, we forget to update addr when we break out of the loop,
which causes us to truncate the range being invalidated as the end
address is exclusive. When we re-enter the loop at the same address, the
page has already been freed and the pte_present test will fail, meaning
that we do not reconsider the address for invalidation.
This patch fixes the problem by incrementing addr by the PAGE_SIZE
before breaking out of the loop on batch failure.
Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
0x4c6e is a secondary device id so should not be used
by the driver.
Noticed-by: Mark Kettenis <mark.kettenis@xs4all.nl> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
evm_inode_setxattr() can be called with no value. The function does not
check the length so that following command can be used to produce the
kernel oops: setfattr -n security.evm FOO. This patch fixes it.
Changes in v3:
* there is no reason to return different error codes for EVM_XATTR_HMAC
and non EVM_XATTR_HMAC. Remove unnecessary test then.
Changes in v2:
* testing for validity of xattr type
In compat mode, we copy each field of snd_pcm_status struct but don't
touch the reserved fields, and this leaves uninitialized values
there. Meanwhile the native ioctl does zero-clear the whole
structure, so we should follow the same rule in compat mode, too.
If a device's dev_pm_ops::freeze callback fails during the QUIESCE
phase, we don't rollback things correctly calling the thaw and complete
callbacks. This could leave some devices in a suspended state in case of
an error during resuming from hibernation.
Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
free_pi_state and exit_pi_state_list both clean up futex_pi_state's.
exit_pi_state_list takes the hb lock first, and most callers of
free_pi_state do too. requeue_pi doesn't, which means free_pi_state
can free the pi_state out from under exit_pi_state_list. For example:
task A | task B
exit_pi_state_list |
pi_state = |
curr->pi_state_list->next |
| futex_requeue(requeue_pi=1)
| // pi_state is the same as
| // the one in task A
| free_pi_state(pi_state)
| list_del_init(&pi_state->list)
| kfree(pi_state)
list_del_init(&pi_state->list) |
Move the free_pi_state calls in requeue_pi to before it drops the hb
locks which it's already holding.
[ tglx: Removed a pointless free_pi_state() call and the hb->lock held
debugging. The latter comes via a seperate patch ]
Signed-off-by: Brian Silverman <bsilver16384@gmail.com> Cc: austin.linux@gmail.com Cc: darren@dvhart.com Cc: peterz@infradead.org Link: http://lkml.kernel.org/r/1414282837-23092-1-git-send-email-bsilver16384@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
If userland creates a timer without specifying a sigevent info, we'll
create one ourself, using a stack local variable. Particularly will we
use the timer ID as sival_int. But as sigev_value is a union containing
a pointer and an int, that assignment will only partially initialize
sigev_value on systems where the size of a pointer is bigger than the
size of an int. On such systems we'll copy the uninitialized stack bytes
from the timer_create() call to userland when the timer actually fires
and we're going to deliver the signal.
Initialize sigev_value with 0 to plug the stack info leak.
Found in the PaX patch, written by the PaX Team.
Fixes: 5a9fa7307285 ("posix-timers: kill ->it_sigev_signo and...") Signed-off-by: Mathias Krause <minipli@googlemail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Brad Spengler <spender@grsecurity.net> Cc: PaX Team <pageexec@freemail.hu> Link: http://lkml.kernel.org/r/1412456799-32339-1-git-send-email-minipli@googlemail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[lizf: Backported to 3.4: adjust filename] Signed-off-by: Zefan Li <lizefan@huawei.com>
On ISOC endpoints the last trb_pool entry used as a
LINK TRB is not getting zeroed out correctly due to
memset being called incorrectly and in the wrong place.
If pool allocated from DMA was not zero-initialized
to begin with this will result in the size and ctrl
values being random garbage. Call memset correctly after
assignment of the trb_link pointer.
Fixes: f6bafc6a1c ("usb: dwc3: convert TRBs into bitshifts") Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Unknown operation numbers are caught in nfsd4_decode_compound() which
sets op->opnum to OP_ILLEGAL and op->status to nfserr_op_illegal. The
error causes the main loop in nfsd4_proc_compound() to skip most
processing. But nfsd4_proc_compound also peeks ahead at the next
operation in one case and doesn't take similar precautions there.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
An official recent Windows driver from FTDI detects counterfeit devices
and reprograms the internal EEPROM containing the USB PID to 0, effectively
bricking the device.
Add support for this VID/PID pair to correctly bind the driver on these
devices.
When sg_scsi_ioctl() fails to prepare request to submit in
blk_rq_map_kern() we jump to a label where we just end up copying
(luckily zeroed-out) kernel buffer to userspace instead of reporting
error. Fix the problem by jumping to the right label.
CC: Jens Axboe <axboe@kernel.dk> CC: linux-scsi@vger.kernel.org
Coverity-id: 1226871 Signed-off-by: Jan Kara <jack@suse.cz>
Fixed up the, now unused, out label.
Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
projects / thirdparty / kernel / stable.git / log
