That check should be for the line sas_target_priv_data->raid_device =
raid_device;
Due to above hunk, we are not initializing raid_device's starget for
raid volumes, and so during raid disk deletion driver is not calling
scsi_remove_target() API as driver observes starget field of
raid_device's structure as NULL.
A system can get hung task timeouts if a qlogic board fails during
initialization (if the board breaks again or fails the init). The hang
involves the scsi scan.
In a nutshell, since commit beb9e315e6e0 ("qla2xxx: Prevent removal and
board_disable race"):
...it is possible to have freed ha (base_vha->hw) early by a call to
qla2x00_remove_one when pdev->enable_cnt equals zero:
if (!atomic_read(&pdev->enable_cnt)) {
scsi_host_put(base_vha->host);
kfree(ha);
pci_set_drvdata(pdev, NULL);
return;
Almost always, the scsi_host_put above frees the vha structure
(attached to the end of the Scsi_Host we're putting) since it's the last
put, and life is good. However, if we are entering this routine because
the adapter has broken sometime during initialization AND a scsi scan is
already in progress (and has done its own scsi_host_get), vha will not
be freed. What's worse, the scsi scan will access the freed ha structure
through qla2xxx_scan_finished:
if (time > vha->hw->loop_reset_delay * HZ)
return 1;
The scsi scan keeps checking to see if a scan is complete by calling
qla2xxx_scan_finished. There is a timeout value that limits the length
of time a scan can take (hw->loop_reset_delay, usually set to 5
seconds), but this definition is in the data structure (hw) that can get
freed early.
This can yield unpredictable results, the worst of which is that the
scsi scan can hang indefinitely. This happens when the freed structure
gets reused and loop_reset_delay gets overwritten with garbage, which
the scan obliviously uses as its timeout value.
The fix for this is simple: at the top of qla2xxx_scan_finished, check
for the UNLOADING bit in the vha structure (_vha is not freed at this
point). If UNLOADING is set, we exit the scan for this adapter
immediately. After this last reference to the ha structure, we'll exit
the scan for this adapter, and continue on.
This problem is hard to hit, but I have run into it doing negative
testing many times now (with a test specifically designed to bring it
out), so I can verify that this fix works. My testing has been against a
RHEL7 driver variant, but the bug and patch are equally relevant to to
the upstream driver.
Fixes: beb9e315e6e0 ("qla2xxx: Prevent removal and board_disable race") Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fix scale configuration/parsing for h3lis331dl accel driver
when sensitivity is higher than 1(m/s^2)/digit
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com> Fixes: 1e52fefc9b0c ("iio: accel: Add support for the h3lis331dl accelerometer") Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing, it was observed that on some platforms the scale value
from iio sysfs for gyroscope is always 0 (E.g. Yoga 260). This results
in the final angular velocity component values to be zeros.
This is caused by insufficient precision of scale value displayed in sysfs.
If the precision is changed to nano from current micro, then this is
sufficient to display the scale value on this platform.
Since this can be a problem for all other HID sensors, increase scale
precision of all HID sensors to nano from current micro.
Results on Yoga 260:
name scale before scale now
--------------------------------------------
gyro_3d 0.000000 0.000000174
als 0.001000 0.001000000
magn_3d 0.000001 0.000001000
accel_3d 0.000009 0.000009806
Signed-off-by: Song Hongyan <hongyan.song@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The boot-time frequency of a CPU is considered its rated maximum, as we
have no other source of such information. However, this was previously
only used for chips with 80% restrictions on secondary PLLs. This
usually wasn't a problem because most chips/configs boot with a divider
of /1, with other dividers being used only for dynamic frequency
reduction. However, at least one config (LS1021A at less than 1 GHz)
uses a different divider for top speed. This was causing cpufreq to set
a frequency beyond the chip's rated speed.
This is fixed by applying a 100%-of-initial-speed limit to all CPU PLLs,
similar to the existing 80% limit that only applied to some.
Signed-off-by: Scott Wood <oss@buserror.net> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bug 150611 uncovered that the WMI ID used by the toshiba-wmi driver
is not Toshiba specific, and as such, the driver was being loaded
on non Toshiba laptops too.
This patch adds a DMI matching list checking for TOSHIBA as the
vendor, refusing to load if it is not.
Also the WMI GUID was renamed, dropping the TOSHIBA_ prefix, to
better reflect that such GUID is not a Toshiba specific one.
Don't pass a size larger than iov_len to kernel_sendmsg().
Otherwise it will cause a NULL pointer deref when kernel_sendmsg()
returns with rv < size.
DRBD as external module has been around in the kernel 2.4 days already.
We used to be compatible to 2.4 and very early 2.6 kernels,
we used to use
rv = sock_sendmsg(sock, &msg, iov.iov_len);
then later changed to
rv = kernel_sendmsg(sock, &msg, &iov, 1, size);
when we should have used
rv = kernel_sendmsg(sock, &msg, &iov, 1, iov.iov_len);
tcp_sendmsg() used to totally ignore the size parameter. 57be5bd ip: convert tcp_sendmsg() to iov_iter primitives
changes that, and exposes our long standing error.
Even with this error exposed, to trigger the bug, we would need to have
an environment (config or otherwise) causing us to not use sendpage()
for larger transfers, a failing connection, and have it fail "just at the
right time". Apparently that was unlikely enough for most, so this went
unnoticed for years.
Still, it is known to trigger at least some of these,
and suspected for the others:
[0] http://lists.linbit.com/pipermail/drbd-user/2016-July/023112.html
[1] http://lists.linbit.com/pipermail/drbd-dev/2016-March/003362.html
[2] https://forums.grsecurity.net/viewtopic.php?f=3&t=4546
[3] https://ubuntuforums.org/showthread.php?t=2336150
[4] http://e2.howsolveproblem.com/i/1175162/
This should go into 4.9,
and into all stable branches since and including v4.0,
which is the first to contain the exposing change.
It is correct for all stable branches older than that as well
(which contain the DRBD driver; which is 2.6.33 and up).
It requires a small "conflict" resolution for v4.4 and earlier, with v4.5
we dropped the comment block immediately preceding the kernel_sendmsg().
Fixes: b411b3637fa7 ("The DRBD driver") Cc: viro@zeniv.linux.org.uk Cc: christoph.lechleitner@iteg.at Cc: wolfgang.glas@iteg.at Reported-by: Christoph Lechleitner <christoph.lechleitner@iteg.at> Tested-by: Christoph Lechleitner <christoph.lechleitner@iteg.at> Signed-off-by: Richard Weinberger <richard@nod.at>
[changed oneliner to be "obvious" without context; more verbose message] Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Dave Miller "the networking stack has a
hard requirement that all SKBs which are transmitted
must have their completion signalled in a fininte
amount of time. This is because, until the SKB is
freed by the driver, it holds onto socket,
netfilter, and other subsystem resources."
In summary, this means that using TX IRQ throttling
for the networking gadgets is, at least, complex and
we should avoid it for the time being.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Suggested-by: David Miller <davem@davemloft.net> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TIOCMIWAIT implementation would return -EINVAL if any of the three
supported signals were included in the mask.
Instead of returning an error in case TIOCM_CTS is included, simply
drop the mask check completely, which is in accordance with how other
drivers implement this ioctl.
Fixes: 5a6a62bdb925 ("cdc-acm: add TIOCMIWAIT") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing the sequence of events in dwc3_core_init() error exit path.
dwc3_core_exit() call is also removed from the error path since,
whatever it's doing is already done.
Fixes: c499ff7 usb: dwc3: core: re-factor init and exit paths Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Greg KH <gregkh@linuxfoundation.org> Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This basicly reverts commit e534f3e9 (staging:nvec: Introduce the use of
the managed version of kzalloc). Serio struct should never by managed
because it is refcounted. Doing so will lead to a double free oops on module
remove.
Signed-off-by: Marc Dietrich <marvin24@gmx.de> Fixes: e534f3e9429f ("staging:nvec: Introduce the use of the managed version of kzalloc") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is necessary to detect paz00 (ac100) touchpad properly as one
speaking ETPS/2 protocol. Without it X.org's synaptics driver doesn't
work as the touchpad is detected as an ImPS/2 mouse instead.
A pass through port is an additional PS/2 port used to connect a slave
device to a master device that is using PS/2 to communicate with the
host (so slave's PS/2 communication is tunneled over master's PS/2
link). "Synaptics PS/2 TouchPad Interfacing Guide" describes such a
setup (PS/2 PASS-THROUGH OPTION section).
Since paz00's embedded controller is not connected to a PS/2 port
itself, the PS/2 interface it exposes is not a pass-through one.
Signed-off-by: Paul Fertser <fercerpav@gmail.com> Acked-by: Marc Dietrich <marvin24@gmx.de> Fixes: 36b30d6138f4 ("staging: nvec: ps2: change serio type to passthrough") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This command was sent behind serio's back and the answer to it was
confusing atkbd probe function which lead to the elantech touchpad
getting detected as a keyboard.
To prevent this from happening just let every party do its part of the
job.
Signed-off-by: Paul Fertser <fercerpav@gmail.com> Acked-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`ni_tio_clock_period_ps()` used to return the clock period in
picoseconds, and had a `BUG()` call for invalid cases. It was changed
to pass the clock period back via a pointer parameter and return an
error for the invalid cases. Unfortunately the code to handle
user-specified clock sources with user-specified clock period is still
returning the clock period the old way, which can lead to the caller not
getting the clock period, or seeing an unexpected error. Fix it by
passing the clock period via the pointer parameter and returning `0`.
Fixes: b42ca86ad605 ("staging: comedi: ni_tio: remove BUG() checks for ni_tio_get_clock_src()") Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Early commit 30ca5cb63c56965 ("staging: sm750fb: change definition of
PANEL_PLANE_TL fields") and 27b047bbe1ee9c0 ("staging: sm750fb: change
definition of PANEL_PLANE_BR fields") modify the register bit fields
definitions. But the modifications are wrong, because the bit mask of
"bit field 10:0" is not 0xeff, but 0x7ff. The wrong definition bugs
makes display very strange.
The ad5933_i2c_read function returns an error code to indicate
whether it could read data or not. However ad5933_work() ignores
this return code and just accesses the data unconditionally,
which gets detected by gcc as a possible bug:
drivers/staging/iio/impedance-analyzer/ad5933.c: In function 'ad5933_work':
drivers/staging/iio/impedance-analyzer/ad5933.c:649:16: warning: 'status' may be used uninitialized in this function [-Wmaybe-uninitialized]
This adds minimal error handling so we only evaluate the
data if it was correctly read.
In the eMMC 4.51 version of the spec, an EXT_CSD field called
GENERIC_CMD6_TIME[248] was added. This allows cards to specify the maximum
time it may need to move out from its busy state, when a CMD6 command has
been sent.
In cases when the card is compliant to versions < 4.51 of the eMMC spec,
obviously the core needs to use a fall-back value for this timeout, which
currently is set to 10 minutes. This value is completely in the wrong range
and importantly in some cases it causes a card initialization to take more
than 10 minute to complete.
Earlier this scenario was avoided as the mmc core used CMD13 to poll the
card, to find out when it stopped signaling busy. Commit 08573eaf1a70
("mmc: mmc: do not use CMD13 to get status after speed mode switch")
changed this behavior.
Instead of reverting that commit, which would cause other issues, let's
instead start by picking a simple solution for the problem, by using a
500ms default generic CMD6 timeout.
The reason for using exactly 500ms, comes from observations that shows it's
quite common for cards to specify 250ms. 500ms is two times that value so
likely it should be enough for most cards.
Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed
mode switch") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Stephen Boyd <sboyd@codeaurora.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the busy response case (i.e. !host->data), an unexpected data interrupt
would result in clearing the data command as though it had completed but
without informing the upper layers and thus resulting in a hang. Fix by
only clearing the data command for data interrupts that are expected.
When converting to a shared library in ac5a181d065d ("cpupower: Add
cpuidle parts into library"), cpu_freq_cpu_exists() was converted to
cpupower_is_cpu_online(). cpu_req_cpu_exists() returned 0 on success and
-ENOSYS on failure whereas cpupower_is_cpu_online returns 1 on success.
Check for the correct return value in cpufreq-set.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1374212 Fixes: ac5a181d065d (cpupower: Add cpuidle parts into library) Reported-by: Julian Seward <jseward@acm.org> Signed-off-by: Laura Abbott <labbott@redhat.com> Acked-by: Thomas Renninger <trenn@suse.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the system is suspended to S3 the BIOS might re-initialize certain
GPIO pins back to their original state or it may re-program interrupt mask
of others. For example Acer TravelMate B116-M had BIOS bug where certain
GPIO pin (MF_ISH_GPIO_5) was programmed to trigger on high level, and the
pin state was high once the BIOS gave control to the OS on resume.
We reset the mask back to known state in chv_pinctrl_resume() but that is
called only after device interrupts have already been enabled.
Now, this particular issue was fixed by upgrading the BIOS to the latest
(v1.23) but not everybody upgrades their BIOSes so we fix it up in the
driver as well.
Prevent the possible interrupt storm by moving suspend and resume hooks to
be called at _noirq time instead. Since device interrupts are still
disabled we can restore the mask back to known state before interrupt storm
happens.
Reported-by: Christian Steiner <christian.steiner@outlook.de> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If async suspend is enabled, the driver may access registers concurrently
with another instance which may fail because of the bug in Cherryview GPIO
hardware. Prevent this by taking the shared lock while accessing the
hardware in suspend and resume hooks.
We used to use generic implementation of dma_map_ops.mmap which is
dma_common_mmap() but that only worked for simpler cached mappings when
vaddr = paddr.
If a driver requests uncached DMA buffer kernel maps it to virtual
address so that MMU gets involved and page uncached status takes into
account. In that case usage of dma_common_mmap() lead to mapping of
vaddr to vaddr for user-space which is obviously wrong. For more detals
please refer to verbose explanation here [1].
So here we implement our own version of mmap() which always deals
with dma_addr and maps underlying memory to user-space properly
(note that DMA buffer mapped to user-space is always uncached
because there's no way to properly manage cache from user-space).
If we're using a shadow copy of a PCI device ROM, the shadow copy is in RAM
and the device never sees accesses to it and doesn't respond to it. We
don't have to route the shadow range to the PCI device, and the device
doesn't have to claim the range.
Previously we treated the shadow copy as though it were the ROM BAR, and we
failed to claim it because the region wasn't routed to the device:
pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
pci_bus 0000:01: Allocating resources
pci 0000:01:00.0: can't claim BAR 6 [mem 0x000c0000-0x000dffff]: no compatible bridge window
The failure path of pcibios_allocate_dev_rom_resource() cleared out the
resource start address, which also caused the following ioremap() warning:
WARNING: CPU: 0 PID: 116 at /build/linux-akdJXO/linux-4.8.0/arch/x86/mm/ioremap.c:121 __ioremap_caller+0x1ec/0x370
ioremap on RAM at 0x0000000000000000 - 0x000000000001ffff
Handle an option ROM shadow copy as RAM, without trying to insert it into
the iomem resource tree.
This fixes a regression caused by 0c0e0736acad ("PCI: Set ROM shadow
location in arch code, not in PCI core"), which appeared in v4.6. The
regression causes video device initialization to fail. This was reported
on AMD Turks, but it likely affects others as well.
The current code doesn't even compile as somehow the inline assembly
can't see the register names defined as ARC_RTC_*
I'm pretty sure It worked when I first got it merged, but the tools were
definitely different then.
Since commit d86bd1bece6f ("mm/slub: support left redzone") it is no longer
guaranteed that kmalloc(PAGE_SIZE) returns page aligned memory.
After the above commit we get an error for diag224 because aligned
memory is required. This leads to the following user visible error:
# mount none -t s390_hypfs /sys/hypervisor/
mount: unknown filesystem type 's390_hypfs'
# dmesg | grep hypfs
hypfs.cccfb8: The hardware system does not provide all functions
required by hypfs
hypfs.7a79f0: Initialization of hypfs failed with rc=-61
Fix this problem and use get_free_page() instead of kmalloc() to get
correctly aligned memory.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It could be not possible to freeze coredumping task when it waits for
'core_state->startup' completion, because threads are frozen in
get_signal() before they got a chance to complete 'core_state->startup'.
Inability to freeze a task during suspend will cause suspend to fail.
Also CRIU uses cgroup freezer during dump operation. So with an
unfreezable task the CRIU dump will fail because it waits for a
transition from 'FREEZING' to 'FROZEN' state which will never happen.
Use freezer_do_not_count() to tell freezer to ignore coredumping task
while it waits for core_state->startup completion.
Link: http://lkml.kernel.org/r/1475225434-3753-1-git-send-email-aryabinin@virtuozzo.com Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Acked-by: Pavel Machek <pavel@ucw.cz> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Tejun Heo <tj@kernel.org> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Error paths in hugetlb_cow() and hugetlb_no_page() may free a newly
allocated huge page.
If a reservation was associated with the huge page, alloc_huge_page()
consumed the reservation while allocating. When the newly allocated
page is freed in free_huge_page(), it will increment the global
reservation count. However, the reservation entry in the reserve map
will remain.
This is not an issue for shared mappings as the entry in the reserve map
indicates a reservation exists. But, an entry in a private mapping
reserve map indicates the reservation was consumed and no longer exists.
This results in an inconsistency between the reserve map and the global
reservation count. This 'leaks' a reserved huge page.
Create a new routine restore_reserve_on_error() to restore the reserve
entry in these specific error paths. This routine makes use of a new
function vma_add_reservation() which will add a reserve entry for a
specific address/page.
In general, these error paths were rarely (if ever) taken on most
architectures. However, powerpc contained arch specific code that that
resulted in an extra fault and execution of these error paths on all
private mappings.
Fixes: 67961f9db8c4 ("mm/hugetlb: fix huge page reserve accounting for private mappings) Link: http://lkml.kernel.org/r/1476933077-23091-2-git-send-email-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com> Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Kirill A . Shutemov <kirill.shutemov@linux.intel.com> Cc: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When root activates a swap partition whose header has the wrong
endianness, nr_badpages elements of badpages are swabbed before
nr_badpages has been checked, leading to a buffer overrun of up to 8GB.
This normally is not a security issue because it can only be exploited
by root (more specifically, a process with CAP_SYS_ADMIN or the ability
to modify a swap file/partition), and such a process can already e.g.
modify swapped-out memory of any other userspace process on the system.
If shmem_alloc_page() does not set PageLocked and PageSwapBacked, then
shmem_replace_page() needs to do so for itself. Without this, it puts
newpage on the wrong lru, re-unlocks the unlocked newpage, and system
descends into "Bad page" reports and freeze; or if CONFIG_DEBUG_VM=y, it
hits an earlier VM_BUG_ON_PAGE(!PageLocked), depending on config.
But shmem_replace_page() is not a common path: it's only called when
swapin (or swapoff) finds the page was already read into an unsuitable
zone: usually all zones are suitable, but gem objects for a few drm
devices (gma500, omapdrm, crestline, broadwater) require zone DMA32 if
there's more than 4GB of ram.
Turns out kmemleak is right. We now allocate the frontswap map
depending on the kernel config (and no longer on the enablement)
swapfile.c:
[...]
if (IS_ENABLED(CONFIG_FRONTSWAP))
frontswap_map = vzalloc(BITS_TO_LONGS(maxpages) * sizeof(long));
but later on this is passed along
--> enable_swap_info(p, prio, swap_map, cluster_info, frontswap_map);
and ignored if frontswap is disabled
--> frontswap_init(p->type, frontswap_map);
static inline void frontswap_init(unsigned type, unsigned long *map)
{
if (frontswap_enabled())
__frontswap_init(type, map);
}
Thing is, that frontswap map is never freed.
The leakage is relatively not that bad, because swapon is an infrequent
and privileged operation. However, if the first frontswap backend is
registered after a swap type has been already enabled, it will WARN_ON
in frontswap_register_ops() and frontswap will not be available for the
swap type.
Fix this by making sure the map is assigned by frontswap_init() as long
as CONFIG_FRONTSWAP is enabled.
Fixes: 8ea1d2a1985a ("mm, frontswap: convert frontswap_enabled to static key") Link: http://lkml.kernel.org/r/20161026134220.2566-1-vbabka@suse.cz Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Reported-by: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Juergen Gross <jgross@suse.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving a nec repeat, ensure the correct scancode is repeated
rather than a random value from the stack. This removes the need for
the bogus uninitialized_var() and also fixes the warnings:
drivers/media/usb/dvb-usb/dib0700_core.c: In function ‘dib0700_rc_urb_completion’:
drivers/media/usb/dvb-usb/dib0700_core.c:679: warning: ‘protocol’ may be used uninitialized in this function
[sean addon: So after writing the patch and submitting it, I've bought the
hardware on ebay. Without this patch you get random scancodes
on nec repeats, which the patch indeed fixes.]
Signed-off-by: Sean Young <sean@mess.org> Tested-by: Sean Young <sean@mess.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mismatching stream names in DAPM route and widget definitions are
causing compilation errors. Fixing these names allows the cs4270
driver to compile and function.
[Errors must be at probe time not compile time -- broonie]
Signed-off-by: Murray Foster <mrafoster@gmail.com> Acked-by: Paul Handrigan <Paul.Handrigan@cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ALSA proc handler allows currently the write in the unlimited size
until kmalloc() fails. But basically the write is supposed to be only
for small inputs, mostly for one line inputs, and we don't have to
handle too large sizes at all. Since the kmalloc error results in the
kernel warning, it's better to limit the size beforehand.
This patch adds the limit of 16kB, which must be large enough for the
currently existing code.
Currently the ALSA proc handler allows read or write even if the proc
file were write-only or read-only. It's mostly harmless, does thing
but allocating memory and ignores the input/output. But it doesn't
tell user about the invalid use, and it's confusing and inconsistent
in comparison with other proc files.
This patch adds some sanity checks and let the proc handler returning
an -EIO error when the invalid read/write is performed.
This patch will fix regression caused by commit 1e793f6fc0db ("scsi:
megaraid_sas: Fix data integrity failure for JBOD (passthrough)
devices").
The problem was that the MEGASAS_IS_LOGICAL macro did not have braces
and as a result the driver ended up exposing a lot of non-existing SCSI
devices (all SCSI commands to channels 1,2,3 were returned as
SUCCESS-DID_OK by driver).
Commit 02b01e010afe ("megaraid_sas: return sync cache call with
success") modified the driver to successfully complete SYNCHRONIZE_CACHE
commands without passing them to the controller. Disk drive caches are
only explicitly managed by controller firmware when operating in RAID
mode. So this commit effectively disabled writeback cache flushing for
any drives used in JBOD mode, leading to data integrity failures.
[mkp: clarified patch description]
Fixes: 02b01e010afeeb49328d35650d70721d2ca3fd59 Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com> Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com> Reviewed-by: Tomas Henzl <thenzl@redhat.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their
original types" changed parameters for csum_tcpudp_magic and
csum_tcpudp_nofold for many platforms but not for PowerPC.
Fixes: 01cfbad "ipv4: Update parameters for csum_tcpudp_magic to their original types" Cc: Alexander Duyck <aduyck@mirantis.com> Signed-off-by: Ivan Vecera <ivecera@redhat.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transmitting on a packet socket with PACKET_VNET_HDR and
PACKET_QDISC_BYPASS, validate device support for features requested
in vnet_hdr.
Drop TSO packets sent to devices that do not support TSO or have the
feature disabled. Note that the latter currently do process those
packets correctly, regardless of not advertising the feature.
Because of SKB_GSO_DODGY, it is not sufficient to test device features
with netif_needs_gso. Full validate_xmit_skb is needed.
Switch to software checksum for non-TSO packets that request checksum
offload if that device feature is unsupported or disabled. Note that
similar to the TSO case, device drivers may perform checksum offload
correctly even when not advertising it.
When switching to software checksum, packets hit skb_checksum_help,
which has two BUG_ON checksum not in linear segment. Packet sockets
always allocate at least up to csum_start + csum_off + 2 as linear.
Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c
Fixes: d346a3fae3ff ("packet: introduce PACKET_QDISC_BYPASS socket option") Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit() when an
IPv6 header is installed to a socket buffer.
This is not a cosmetic change. Without updating this value, GSO packets
transmitted through an ipip6 tunnel have the protocol of ETH_P_IP and
skb_mac_gso_segment() will attempt to call gso_segment() for IPv4,
which results in the packets being dropped.
Fixes: b8921ca83eed ("ip4ip6: Support for GSO/GRO") Signed-off-by: Eli Cooper <elicooper@gmx.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrey Konovalov reported that KASAN detected that SCTP was using a slab
beyond the boundaries. It was caused because when handling out of the
blue packets in function sctp_sf_ootb() it was checking the chunk len
only after already processing the first chunk, validating only for the
2nd and subsequent ones.
The fix is to just move the check upwards so it's also validated for the
1st chunk.
Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While trying out [1][2], I noticed that tc monitor doesn't show the
correct handle on delete:
$ tc monitor
qdisc clsact ffff: dev eno1 parent ffff:fff1
filter dev eno1 ingress protocol all pref 49152 bpf handle 0x2a [...]
deleted filter dev eno1 ingress protocol all pref 49152 bpf handle 0xf3be0c80
some context to explain the above:
The user identity of any tc filter is represented by a 32-bit
identifier encoded in tcm->tcm_handle. Example 0x2a in the bpf filter
above. A user wishing to delete, get or even modify a specific filter
uses this handle to reference it.
Every classifier is free to provide its own semantics for the 32 bit handle.
Example: classifiers like u32 use schemes like 800:1:801 to describe
the semantics of their filters represented as hash table, bucket and
node ids etc.
Classifiers also have internal per-filter representation which is different
from this externally visible identity. Most classifiers set this
internal representation to be a pointer address (which allows fast retrieval
of said filters in their implementations). This internal representation
is referenced with the "fh" variable in the kernel control code.
When a user successfuly deletes a specific filter, by specifying the correct
tcm->tcm_handle, an event is generated to user space which indicates
which specific filter was deleted.
Before this patch, the "fh" value was sent to user space as the identity.
As an example what is shown in the sample bpf filter delete event above
is 0xf3be0c80. This is infact a 32-bit truncation of 0xffff8807f3be0c80
which happens to be a 64-bit memory address of the internal filter
representation (address of the corresponding filter's struct cls_bpf_prog);
After this patch the appropriate user identifiable handle as encoded
in the originating request tcm->tcm_handle is generated in the event.
One of the cardinal rules of netlink rules is to be able to take an
event (such as a delete in this case) and reflect it back to the
kernel and successfully delete the filter. This patch achieves that.
Note, this issue has existed since the original TC action
infrastructure code patch back in 2004 as found in:
https://git.kernel.org/cgit/linux/kernel/git/history/history.git/commit/
Fixes: 4e54c4816bfe ("[NET]: Add tc extensions infrastructure.") Reported-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to IPv4, do not consider link state when validating next hops.
Currently, if the link is down default routes can fail to insert:
$ ip -6 ro add vrf blue default via 2100:2::64 dev eth2
RTNETLINK answers: No route to host
With this patch the command succeeds.
Fixes: 8c14586fc320 ("net: ipv6: Use passed in table for nexthop lookups") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if sending SCIs is explicitly disabled, the code that creates the
Security Tag might still decide to add it (e.g. if multiple RX SCs are
defined on the MACsec interface).
But because the header length so far only depended on the configuration
option the SCI overwrote the original frame's contents (EtherType and
e.g. the beginning of the IP header) and if encrypted did not visibly
end up in the packet, while the SC flag in the TCI field of the Security
Tag was still set, resulting in invalid MACsec frames.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Tobias Brunner <tobias@strongswan.org> Acked-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Hyper-V netvsc driver was looking at the incorrect status bits
in the checksum info. It was setting the receive checksum unnecessary
flag based on the IP header checksum being correct. The checksum
flag is skb is about TCP and UDP checksum status. Because of this
bug, any packet received with bad TCP checksum would be passed
up the stack and to the application causing data corruption.
The problem is reproducible via netcat and netem.
This had a side effect of not doing receive checksum offload
on IPv6. The driver was also also always doing checksum offload
independent of the checksum setting done via ethtool.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First bug was added in commit ad6f939ab193 ("ip: Add offset parameter to
ip_cmsg_recv") : Tom missed that ipv4 udp messages could be received on
AF_INET6 socket. ip_cmsg_recv(msg, skb) should have been replaced by
ip_cmsg_recv_offset(msg, skb, sizeof(struct udphdr));
Then commit e6afc8ace6dd ("udp: remove headers from UDP packets before
queueing") forgot to adjust the offsets now UDP headers are pulled
before skb are put in receive queue.
Fixes: ad6f939ab193 ("ip: Add offset parameter to ip_cmsg_recv") Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Sam Kumar <samanthakumar@google.com> Cc: Willem de Bruijn <willemb@google.com> Tested-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7303a1475008 ("sctp: identify chunks that need to be fragmented
at IP level") made the chunk be fragmented at IP level in the next round
if it's size exceed PMTU.
But there still is another case, PMTU can be updated if transport's dst
expires and transport's pmtu_pending is set in sctp_packet_transmit. If
the new PMTU is less than the chunk, the same issue with that commit can
be triggered.
So we should drop this packet and let it retransmit in another round
where it would be fragmented at IP level.
This patch is to fix it by checking the chunk size after PMTU may be
updated and dropping this packet if it's size exceed PMTU.
Fixes: 90017accff61 ("sctp: Add GSO support") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@txudriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of getsockopt handlers in net/sctp/socket.c check len against
sizeof some structure like:
if (len < sizeof(int))
return -EINVAL;
On the first look, the check seems to be correct. But since len is int
and sizeof returns size_t, int gets promoted to unsigned size_t too. So
the test returns false for negative lengths. Yes, (-1 < sizeof(long)) is
false.
Fix this in sctp by explicitly checking len < 0 before any getsockopt
handler is called.
Note that sctp_getsockopt_events already handled the negative case.
Since we added the < 0 check elsewhere, this one can be removed.
Commit 3ac72b7b63d5 ("net: fec: align IP header in hardware") breaks
networking on mx28.
There is an erratum on mx28 (ENGR121613 - ENET big endian mode
not compatible with ARM little endian) that requires an additional
byte-swap operation to workaround this problem.
So call swap_buffer() prior to performing the IP header alignment
to restore network functionality on mx28.
Fixes: 3ac72b7b63d5 ("net: fec: align IP header in hardware") Reported-and-tested-by: Henri Roosen <henri.roosen@ginzinger.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit a681574c99be23e4d20b769bf0e543239c364af5
("ipv4: disable BH in set_ping_group_range()") because we never
read ping_group_range in BH context (unlike local_port_range).
Then, since we already have a lock for ping_group_range, those
using ip_local_ports.lock for ping_group_range are clearly typos.
We might consider to share a same lock for both ping_group_range
and local_port_range w.r.t. space saving, but that should be for
net-next.
Fixes: a681574c99be ("ipv4: disable BH in set_ping_group_range()") Fixes: ba6b918ab234 ("ping: move ping_group_range out of CONFIG_SYSCTL") Cc: Eric Dumazet <edumazet@google.com> Cc: Eric Salo <salo@google.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 4ee3bd4a8c746 ("ipv4: disable BH when changing ip local port
range") Cong added BH protection in set_local_port_range() but missed
that same fix was needed in set_ping_group_range()
Fixes: b8f1a55639e6 ("udp: Add function to make source port for UDP tunnels") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Eric Salo <salo@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, GRO can do unlimited recursion through the gro_receive
handlers. This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem. Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.
This patch adds a recursion counter to the GRO layer to prevent stack
overflow. When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally. This recursion
counter is put in the GRO CB, but could be turned into a percpu counter
if we run out of space in the CB.
Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.
Fixes: CVE-2016-7039 Fixes: 9b174d88c257 ("net: Add Transparent Ethernet Bridging GRO support.") Fixes: 66e5133f19e9 ("vlan: Add GRO support for non hardware accelerated vlan") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Jiri Benc <jbenc@redhat.com> Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Acked-by: Tom Herbert <tom@herbertland.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that netdev_all_lower_get_next_rcu() never advances the
iterator, thereby causing the loop over the lower adjacency list to run
forever.
Fix this by advancing the iterator and avoid the infinite loop.
Fixes: 7ce856aaaf13 ("mlxsw: spectrum: Add couple of lower device helper functions") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Tamir Winetroub <tamirw@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Acked-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The offload flag is a status flag and should not be used by
FIB semantics for comparison.
Fixes: 37ed9493699c ("rtnetlink: add RTNH_F_EXTERNAL flag for fib offload") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is that the 8021q module propagates the call to
ndo_bridge_getlink() via switchdev ops, but the switch driver doesn't
recognize the netdev, as it's not offloaded.
While we can ignore calls being made to non-bridge ports inside the
driver, a better fix would be to push this check up to the switchdev
layer.
Note that these ndos can be called for non-bridged netdev, but this only
happens in certain PF drivers which don't call the corresponding
switchdev functions anyway.
Fixes: 99f44bb3527b ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Tamir Winetroub <tamirw@mellanox.com> Tested-by: Tamir Winetroub <tamirw@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Satish reported a problem with the perm multicast router ports not getting
reenabled after some series of events, in particular if it happens that the
multicast snooping has been disabled and the port goes to disabled state
then it will be deleted from the router port list, but if it moves into
non-disabled state it will not be re-added because the mcast snooping is
still disabled, and enabling snooping later does nothing.
Here are the steps to reproduce, setup br0 with snooping enabled and eth1
added as a perm router (multicast_router = 2):
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
<empty>
At this point we have mcast enabled and eth1 as a perm router (value = 2)
but it is not in the router list which is incorrect.
After this change:
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
router ports on br0: eth1
Note: we can directly do br_multicast_enable_port for all because the
querier timer already has checks for the port state and will simply
expire if it's in blocking/disabled. See the comment added by
commit 9aa66382163e7 ("bridge: multicast: add a comment to
br_port_state_selection about blocking state")
Fixes: 561f1103a2b7 ("bridge: Add multicast_snooping sysfs toggle") Reported-by: Satish Ashok <sashok@cumulusnetworks.com> Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After Jesper commit back in linux-3.18, we trigger a lockdep
splat in proc_create_data() while allocating memory from
pktgen_change_name().
This patch converts t->if_lock to a mutex, since it is now only
used from control path, and adds proper locking to pktgen_change_name()
1) pktgen_thread_lock to protect the outer loop (iterating threads)
2) t->if_lock to protect the inner loop (iterating devices)
Note that before Jesper patch, pktgen_change_name() was lacking proper
protection, but lockdep was not able to detect the problem.
Fixes: 8788370a1d4b ("pktgen: RCU-ify "if_list" to remove lock in next_to_run()") Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In cases where the number of tx rings is not a multiple of the number of
rx rings, the tx completion event will be handled on a different core
from the transmit and population of the ring. Races on the ring will
lead to a double-free of the page, and possibly other corruption.
The rings are initialized by default with a valid multiple of rings,
based on the number of cpus, therefore an invalid configuration requires
ethtool to change the ring layout. For instance 'ethtool -L eth0 rx 9 tx
8' will cause packets received on rx0, and XDP_TX'd to tx48, to be
completed on cpu3 (48 % 9 == 3).
Resolve this discrepancy by shifting the irq for the xdp tx queues to
start again from 0, modulo rx_ring_num.
Fixes: 9ecc2d86171a ("net/mlx4_en: add xdp forwarding and data write support") Reported-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Brenden Blanco <bblanco@plumgrid.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the commit 9207f9d45b0a ("net: preserve IP control block
during GSO segmentation"), the GSO CB and the IPoIB CB conflict.
That destroy the IPoIB address information cached there,
causing a severe performance regression, as better described here:
This change moves the data cached by the IPoIB driver from the
skb control lock into the IPoIB hard header, as done before
the commit 936d7de3d736 ("IPoIB: Stop lying about hard_header_len
and use skb->cb to stash LL addresses").
In order to avoid GRO issue, on packet reception, the IPoIB driver
stash into the skb a dummy pseudo header, so that the received
packets have actually a hard header matching the declared length.
To avoid changing the connected mode maximum mtu, the allocated
head buffer size is increased by the pseudo header length.
After this commit, IPoIB performances are back to pre-regression
value.
v2 -> v3: rebased
v1 -> v2: avoid changing the max mtu, increasing the head buf size
Fixes: 9207f9d45b0a ("net: preserve IP control block during GSO segmentation") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The goal of the patch is to fix this scenario:
ip link add dummy1 type dummy
ip link set dummy1 up
ip link set lo down ; ip link set lo up
After that sequence, the local route to the link layer address of dummy1 is
not there anymore.
When the loopback is set down, all local routes are deleted by
addrconf_ifdown()/rt6_ifdown(). At this time, the rt6_info entry still
exists, because the corresponding idev has a reference on it. After the rcu
grace period, dst_rcu_free() is called, and thus ___dst_free(), which will
set obsolete to DST_OBSOLETE_DEAD.
In this case, init_loopback() is called before dst_rcu_free(), thus
obsolete is still sets to something <= 0. So, the function doesn't add the
route again. To avoid that race, let's check the rt6 refcnt instead.
Fixes: 25fb6ca4ed9c ("net IPv6 : Fix broken IPv6 routing table after loopback down-up") Fixes: a881ae1f625c ("ipv6: don't call addrconf_dst_alloc again when enable lo") Fixes: 33d99113b110 ("ipv6: reallocate addrconf router for ipv6 address when lo device up") Reported-by: Francesco Santoro <francesco.santoro@6wind.com> Reported-by: Samuel Gauthier <samuel.gauthier@6wind.com> CC: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com> CC: Maruthi Thotad <Maruthi.Thotad@ap.sony.com> CC: Sabrina Dubroca <sd@queasysnail.net> CC: Hannes Frederic Sowa <hannes@stressinduktion.org> CC: Weilong Chen <chenweilong@huawei.com> CC: Gao feng <gaofeng@cn.fujitsu.com> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel
endpoints.") introduces support for wildcards in tunnels endpoints,
but in some rare circumstances ip6_tnl_lookup selects wrong tunnel
interface relying only on source or destination address of the packet
and not checking presence of wildcard in tunnels endpoints. Later in
ip6_tnl_rcv this packets can be dicarded because of difference in
ipproto even if fallback device have proper ipproto configuration.
This patch adds checks of wildcard endpoint in tunnel avoiding such
behavior
Fixes: ea3dc9601bda ("ip6_tunnel: Add support for wildcard tunnel endpoints.") Signed-off-by: Vadim Fedorenko <junk@yandex-team.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The phy_start() is used to indicate the PHY is now ready to do its
work. The state is changed, normally to PHY_UP which means that both
the MAC and the PHY are ready.
If the phy driver is using polling, when the next poll happens, the
state machine notices the PHY is now in PHY_UP, and kicks off
auto-negotiation, if needed.
If however, the PHY is using interrupts, there is no polling. The phy
is stuck in PHY_UP until the next interrupt comes along. And there is
no reason for the PHY to interrupt.
Have phy_start() schedule the state machine to run, which both speeds
up the polling use case, and makes the interrupt use case actually
work.
This problems exists whenever there is a state change which will not
cause an interrupt. Trigger the state machine in these cases,
e.g. phy_error().
Signed-off-by: Andrew Lunn <andrew@lunn.ch> Cc: Kyle Roeschley <kyle.roeschley@ni.com> Tested-by: Kyle Roeschley <kyle.roeschley@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issue is that ip6_datagram_recv_specific_ctl() expects to find IP6CB
data that was moved at a different place in tcp_v6_rcv()
This patch moves tcp_v6_restore_cb() up and calls it from
tcp_v6_do_rcv() when np->pktoptions is set.
Fixes: 971f10eca186 ("tcp: better TCP_SKB_CB layout to reduce cache line misses") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Baozeng Ding <sploving1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Krister reported a kernel NULL pointer dereference after
tcf_action_init_1() invokes a_o->init(), it is a race condition
where one thread calling tcf_register_action() to initialize
the netns data after putting act ops in the global list and
the other thread searching the list and then calling
a_o->init(net, ...).
Fix this by moving the pernet ops registration before making
the action ops visible. This is fine because: a) we don't
rely on act_base in pernet ops->init(), b) in the worst case we
have a fully initialized netns but ops is still not ready so
new actions still can't be created.
Reported-by: Krister Johansen <kjlx@templeofstupid.com> Tested-by: Krister Johansen <kjlx@templeofstupid.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reserved field precise_offset->rsv is not cleared before being
copied to user space, leaking kernel stack memory. Clear the struct
before it's copied.
Signed-off-by: Vlad Tsyrklevich <vlad@tsyrklevich.net> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since linux-3.15, netlink_dump() can use up to 16384 bytes skb
allocations.
Due to struct skb_shared_info ~320 bytes overhead, we end up using
order-3 (on x86) page allocations, that might trigger direct reclaim and
add stress.
The intent was really to attempt a large allocation but immediately
fallback to a smaller one (order-1 on x86) in case of memory stress.
On recent kernels (linux-4.4), we can remove __GFP_DIRECT_RECLAIM to
meet the goal. Old kernels would need to remove __GFP_WAIT
While we are at it, since we do an order-3 allocation, allow to use
all the allocated bytes instead of 16384 to reduce syscalls during
large dumps.
If a socket has FANOUT sockopt set, a new proto_hook is registered
as part of fanout_add(). When processing a NETDEV_UNREGISTER event in
af_packet, __fanout_unlink is called for all sockets, but prot_hook which was
registered as part of fanout_add is not removed. Call fanout_release, on a
NETDEV_UNREGISTER, which removes prot_hook and removes fanout from the
fanout_list.
This fixes BUG_ON(!list_empty(&dev->ptype_specific)) in netdev_run_todo()
Signed-off-by: Anoob Soman <anoob.soman@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a respin of a patch to fix a relatively easily reproducible kernel
panic related to the all_adj_list handling for netdevs in recent kernels.
The following sequence of commands will reproduce the issue:
ip link add link eth0 name eth0.100 type vlan id 100
ip link add link eth0 name eth0.200 type vlan id 200
ip link add name testbr type bridge
ip link set eth0.100 master testbr
ip link set eth0.200 master testbr
ip link add link testbr mac0 type macvlan
ip link delete dev testbr
This creates an upper/lower tree of (excuse the poor ASCII art):
/---eth0.100-eth0
mac0-testbr-
\---eth0.200-eth0
When testbr is deleted, the all_adj_lists are walked, and eth0 is deleted twice from
the mac0 list. Unfortunately, during setup in __netdev_upper_dev_link, only one
reference to eth0 is added, so this results in a panic.
This change adds reference count propagation so things are handled properly.
Matthias Schiffer reported a similar crash in batman-adv:
Signed-off-by: Andrew Collins <acollins@cradlepoint.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generic skb_vlan_push/skb_vlan_pop functions don't properly handle the
case where the input skb data pointer does not point at the mac header:
- They're doing push/pop, but fail to properly unwind data back to its
original location.
For example, in the skb_vlan_push case, any subsequent
'skb_push(skb, skb->mac_len)' calls make the skb->data point 4 bytes
BEFORE start of frame, leading to bogus frames that may be transmitted.
- They update rcsum per the added/removed 4 bytes tag.
Alas if data is originally after the vlan/eth headers, then these
bytes were already pulled out of the csum.
OTOH calling skb_vlan_push/skb_vlan_pop with skb->data at mac_header
present no issues.
act_vlan is the only caller to skb_vlan_*() that has skb->data pointing
at network header (upon ingress).
Other calles (ovs, bpf) already adjust skb->data at mac_header.
This patch fixes act_vlan to point to the mac_header prior calling
skb_vlan_*() functions, as other callers do.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Pravin Shelar <pshelar@ovn.org> Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 879c7220e828 ("net: pktgen: Observe needed_headroom
of the device") increased the 'pkt_overhead' field value by
LL_RESERVED_SPACE.
As a side effect the generated packet size, computed as:
is decreased by the same value.
The above changed slightly the behavior of existing pktgen users,
and made the procfs interface somewhat inconsistent.
Fix it by restoring the previous pkt_overhead value and using
LL_RESERVED_SPACE as extralen in skb allocation.
Also, change pktgen_alloc_skb() to only partially reserve
the headroom to allow the caller to prefetch from ll header
start.
v1 -> v2:
- fixed some typos in the comments
Fixes: 879c7220e828 ("net: pktgen: Observe needed_headroom of the device") Suggested-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the mac address origin is not dt, you can only safely assign a mac
address after "link up" of the device. If the link is off the clocks are
disabled and because of issues assigning registers when clocks are off the
new mac address cannot be written in .ndo_set_mac_address() on some soc's.
This fix sets the mac address unconditionally in fec_restart(...) and
ensures consistency between fec registers and the network layer.
Signed-off-by: Gavin Schenk <g.schenk@eckelmann.de> Acked-by: Fugang Duan <fugang.duan@nxp.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Fixes: 9638d19e4816 ("net: fec: add netif status check before set mac address") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit a4675fbc4a7a (cpufreq: intel_pstate: Replace timers with
utilization update callbacks) the cpufreq governor callbacks may not
be invoked on NOHZ_FULL CPUs and, in particular, switching to the
"performance" policy via sysfs may not have any effect on them. That
is a problem, because it usually is desirable to squeeze the last
bit of performance out of those CPUs, so work around it by setting
the maximum P-state (within the limits) in intel_pstate_set_policy()
upfront when the policy is CPUFREQ_POLICY_PERFORMANCE.
Fixes: a4675fbc4a7a (cpufreq: intel_pstate: Replace timers with utilization update callbacks) Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e96a8a3bb671 ("UBI: Fastmap: Do not add vol if it already
exists") introduced a bug by changing the possible error codes returned
by add_vol():
- this function no longer returns NULL in case of allocation failure
but return ERR_PTR(-ENOMEM)
- when a duplicate entry in the volume RB tree is found it returns
ERR_PTR(-EEXIST) instead of ERR_PTR(-EINVAL)
Fix the tests done on add_vol() return val to match this new behavior.
Fixes: e96a8a3bb671 ("UBI: Fastmap: Do not add vol if it already exists") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Sheng Yong <shengyong1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While free'ing qgroup->reserved resources, we much check if
the page has not been invalidated by a truncate operation
by checking if the page is still dirty before reducing the
qgroup resources. Resources in such a case are free'd when
the entire extent is released by delayed_ref.
This fixes a double accounting while releasing resources
in case of truncating a file, reproduced by the following testcase.
SCRATCH_DEV=/dev/vdb
SCRATCH_MNT=/mnt
mkfs.btrfs -f $SCRATCH_DEV
mount -t btrfs $SCRATCH_DEV $SCRATCH_MNT
cd $SCRATCH_MNT
btrfs quota enable $SCRATCH_MNT
btrfs subvolume create a
btrfs qgroup limit 500m a $SCRATCH_MNT
sync
for c in {1..15}; do
dd if=/dev/zero bs=1M count=40 of=$SCRATCH_MNT/a/file;
done
Commit 41061cdb98 ("KVM: emulate: do not initialize memopp") removes a
check for non-NULL under incorrect assumptions. An undefined instruction
with a ModR/M byte with Mod=0 and R/M-5 (e.g. 0xc7 0x15) will attempt
to dereference a null pointer here.
Alexander Shiyan reports that CLPS711x fails at boot time in the data
exception handler due to a NULL pointer dereference. This is caused by
the late-v4t abort handler overwriting R9 (which becomes zero). Fix
this by making the abort handler save and restore R9.
Fixes: e6978e4bf181 ("ARM: save and reset the address limit when entering an exception") Reported-by: Alexander Shiyan <shc_work@mail.ru> Tested-by: Alexander Shiyan <shc_work@mail.ru> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In csi_J(3), the third parameter of scr_memsetw (vc_screenbuf_size) is
divided by 2 inappropriatelly. But scr_memsetw expects size, not
count, because it divides the size by 2 on its own before doing actual
memset-by-words.
Pipelines can only be run if all their video nodes are streaming. Commit b4dfb9b35a19 ("[media] v4l: vsp1: Stop the pipeline upon the first
STREAMOFF") fixed the pipeline stop sequence, but introduced a race
condition that makes it possible to run a pipeline after stopping the
stream on a video node by queuing a buffer on the other side of the
pipeline.
Fix this by clearing the buffers ready flag when stopping the stream,
which will prevent the QBUF handler from running the pipeline.
Fixes: b4dfb9b35a19 ("[media] v4l: vsp1: Stop the pipeline upon the first STREAMOFF") Reported-by: Kieran Bingham <kieran@bingham.xyz> Tested-by: Kieran Bingham <kieran@bingham.xyz> Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we configure musb with 2430 glue as a peripheral, and then rmmod
omap2430 module, we'll get the following error:
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
...
rmmod/413 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
(&phy->mutex){+.+.+.}, at: [<c04b9fd0>] phy_power_off+0x1c/0xb8
[ 204.678710]
and this task is already holding:
(&(&musb->lock)->rlock){-.-...}, at: [<bf3a482c>]
musb_gadget_stop+0x24/0xec [musb_hdrc]
which would create a new lock dependency:
(&(&musb->lock)->rlock){-.-...} -> (&phy->mutex){+.+.+.}
...
This is because some glue layers expect musb_platform_enable/disable
to be called with spinlock held, and 2430 glue layer has USB PHY on
the I2C bus using a mutex.
We could fix the glue layers to take the spinlock, but we still have
a problem of musb_plaform_enable/disable being called in an unbalanced
manner. So that would still lead into USB PHY enable/disable related
problems for omap2430 glue layer.
While it makes sense to only enable USB PHY when needed from PM point
of view, in this case we just can't do it yet without breaking things.
So let's just revert phy_enable/disable related changes instead and
reconsider this after we have fixed musb_platform_enable/disable to
be balanced.
Fixes: a83e17d0f73b ("usb: musb: Improve PM runtime and phy handling for 2430 glue layer") Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit b09b5224fe86 ("usb: chipidea: implement platform shutdown
callback") and commit 43a404577a93 ("usb: chipidea: host: set host to
be null after hcd is freed") a NULL pointer dereference is caused
on i.MX23 during shutdown. So ensure that role is set to CI_ROLE_END and
we finish interrupt handling before the hcd is deallocated. This avoids
the NULL pointer dereference.
Suggested-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: b09b5224fe86 ("usb: chipidea: implement platform shutdown callback") Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2abd9d5fa60f9 ("usb: dwc3: ep0: Add chained TRB support"), the
size of the memory allocated with 'dma_alloc_coherent()' has been modified
but the corresponding calls to 'dma_free_coherent()' have not been updated
accordingly.
This has been spotted with coccinelle, using the following script:
////////////////////
@r@
expression x0, x1, y0, y1, z0, z1, t0, t1, ret;
@@
Exported pwm channels aren't removed before the pwmchip and are
leaked. This results in invalid sysfs files. This fix removes
all exported pwm channels before chip removal.
As part of the sync framework destaging, the sync_file.h header
was moved, but an entry was not added on Kbuild to install it.
This patch resolves this omission so that "make headers_install"
installs this header.
Fixes: 460bfc41fd52 ("dma-buf/sync_file: de-stage sync_file headers") Reported-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Emilio López <emilio.lopez@collabora.co.uk> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/20160927143142.8975-1-emilio.lopez@collabora.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scan_pool() does not mark the PEB for scrubing when bitflips are
detected in the EC header of a free PEB (VID header region left to
0xff).
Make sure we scrub the PEB in this case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: dbb7d2a88d2a ("UBI: Add fastmap core") Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Justin and Chris spotted that iptables NFLOG target was broken when they
upgraded the kernel to 4.8: "ulogd-2.0.5- IPs are no longer logged" or
"results in segfaults in ulogd-2.0.5".
Because "struct nf_loginfo li;" is a local variable, and flags will be
filled with garbage value, not inited to zero. So if it contains 0x1,
packets will not be logged to the userspace anymore.
Fixes: 7643507fe8b5 ("netfilter: xt_NFLOG: nflog-range does not truncate packets") Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com> Reported-by: Chris Caputo <ccaputo@alt.net> Tested-by: Chris Caputo <ccaputo@alt.net> Signed-off-by: Liping Zhang <liping.zhang@spreadtrum.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instantiated I2C device nodes are marked with OF_POPULATE. This was
introduced in 4f001fd30145a6. On unloading, loaded device nodes will of
course be unmarked. The problem are nodes that fail during
initialisation: If a node fails, it won't be unloaded and hence not be
unmarked.
If a I2C driver module is unloaded and reloaded, it will skip nodes that
failed before.
Skip device nodes that are already populated and mark them only in case
of success.
Fixes: 4f001fd30145a6 ("i2c: Mark instantiated device nodes with OF_POPULATE") Signed-off-by: Ralf Ramsauer <ralf@ramses-pyramidenbau.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[wsa: use 14-digit commit sha] Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous code would wait for fences on the framebuffer from the old
plane state to complete, rather than the new, so you would see tearing
everywhere. Fix this to wait on the new state before we make it active.
Signed-off-by: Daniel Stone <daniels@collabora.com> Fixes: 94f050246b42 ("drm/i915: nonblocking commit") Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161021144454.6288-1-daniels@collabora.com
(cherry picked from commit 2d2c5ad83f772d7d7b0bb8348ecea42e88f89ab0) Signed-off-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Broadwell and newer actually compress up to 2560 lines instead of 2048
(as documented in the FBC_CTL page). If we don't take this into
consideration we end up reserving too little stolen memory for the
CFB, so we may allocate something else (such as a ring) right after
what we reserved, and the hardware will overwrite it with the contents
of the CFB when FBC is active, causing GPU hangs. Another possibility
is that the CFB may be allocated at the very end of the available
space, so the CFB will overlap the reserved stolen area, leading to
FIFO underruns.
This bug has always been a problem on BDW (the only affected platform
where FBC is enabled by default), but it's much easier to reproduce
since the following commit:
commit c58b735fc762e891481e92af7124b85cb0a51fce
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Aug 18 17:16:57 2016 +0100
drm/i915: Allocate rings from stolen
Of course, you can only reproduce the bug if your screen is taller
than 2048 lines.
Now that we use the AUX and GMBUS assignment from VBT for all ports,
let's clean up the sanitization of the port information a bit.
Previosuly we only did this for port E, and only complained about a
non-standard assignment for the other ports. But as we know that
non-standard assignments are a fact of life, let's expand the
sanitization to all the ports.
v2: Include a commit message, fix up the comments a bit
v3: Don't clobber other ports if the current port has no alternate aux ch/ddc pin
The VBT provides the platform a way to mix and match the DDI ports vs.
AUX channels. Currently we only trust the VBT for DDI E, which has no
corresponding AUX channel of its own. However it is possible that some
board might use some non-standard DDI vs. AUX port routing even for
the other ports. Perhaps for signal routing reasons or something,
So let's generalize this and trust the VBT for all ports.
For now we'll limit this to DDI platforms, as we trust the VBT a bit
more there anyway when it comes to the DDI ports. I've structured
the code in a way that would allow us to easily expand this to
other platforms as well, by simply filling in the ddi_port_info.
v2: Drop whitespace changes, keep MISSING_CASE() for unknown
aux ch assignment, include a commit message, include debug
message during init
drm_property_lookup_blob() returns a reference to the returned blob, and
drm_atomic_replace_property_blob() takes a references to the blob it
stores, so afterwards we are left owning a reference to the new_blob that
we never release, and thus leak memory every time we update a property
such as during drm_atomic_helper_legacy_gamma_set().
v2: update credentials, drm_property_unreference_blob() is NULL safe and
NULL is passed consistently to it throughout drm_atomic.c so do so here.
Reported-by: Felix Monninger <felix.monninger@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98420 Signed-off-by: Felix Monninger <felix.monninger@gmail.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Fixes: 5488dc16fde7 ("drm: introduce pipe color correction properties") Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/20161025212808.3908-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / thirdparty / kernel / stable.git / log
