The nbpf->chan[] array is allocated earlier in the nbpf_probe() function
and it has "num_channels" elements. These three loops iterate one
element farther than they should and corrupt memory.
The changes to the second loop are more involved. In this case, we're
copying data from the irqbuf[] array into the nbpf->chan[] array. If
the data in irqbuf[i] is the error IRQ then we skip it, so the iterators
are not in sync. I added a check to ensure that we don't go beyond the
end of the irqbuf[] array. I'm pretty sure this can't happen, but it
seemed harmless to add a check.
On the other hand, after the loop has ended there is a check to ensure
that the "chan" iterator is where we expect it to be. In the original
code we went one element beyond the end of the array so the iterator
wasn't in the correct place and it would always return -EINVAL. However,
now it will always be in the correct place. I deleted the check since
we know the result.
Cc: stable@vger.kernel.org Fixes: b45b262cefd5 ("dmaengine: add a driver for AMBA AXI NBPF DMAC IP cores") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/b13c5225-7eff-448c-badc-a2c98e9bcaca@sabinyo.mountain Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When MSG_DONTWAIT is not set, the tpacket_snd operation will wait for
pending_refcnt to decrement to zero before returning. The pending_refcnt
is decremented by 1 when the skb->destructor function is called,
indicating that the skb has been successfully sent and needs to be
destroyed.
If an error occurs during this process, the tpacket_snd() function will
exit and return error, but pending_refcnt may not yet have decremented to
zero. Assuming the next send operation is executed immediately, but there
are no available frames to be sent in tx_ring (i.e., packet_current_frame
returns NULL), and skb is also NULL, the function will not execute
wait_for_completion_interruptible_timeout() to yield the CPU. Instead, it
will enter a do-while loop, waiting for pending_refcnt to be zero. Even
if the previous skb has completed transmission, the skb->destructor
function can only be invoked in the ksoftirqd thread (assuming NAPI
threading is enabled). When both the ksoftirqd thread and the tpacket_snd
operation happen to run on the same CPU, and the CPU trapped in the
do-while loop without yielding, the ksoftirqd thread will not get
scheduled to run. As a result, pending_refcnt will never be reduced to
zero, and the do-while loop cannot exit, eventually leading to a CPU soft
lockup issue.
In fact, skb is true for all but the first iterations of that loop, and
as long as pending_refcnt is not zero, even if incremented by a previous
call, wait_for_completion_interruptible_timeout() should be executed to
yield the CPU, allowing the ksoftirqd thread to be scheduled. Therefore,
the execution condition of this function should be modified to check if
pending_refcnt is not zero, instead of check skb.
- if (need_wait && skb) {
+ if (need_wait && packet_read_pending(&po->tx_ring)) {
As a result, the judgment conditions are duplicated with the end code of
the while loop, and packet_read_pending() is a very expensive function.
Actually, this loop can only exit when ph is NULL, so the loop condition
can be changed to while (1), and in the "ph = NULL" branch, if the
subsequent condition of if is not met, the loop can break directly. Now,
the loop logic remains the same as origin but is clearer and more obvious.
Fixes: 89ed5b519004 ("af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET") Cc: stable@kernel.org Suggested-by: LongJun Tang <tanglongjun@kylinos.cn> Signed-off-by: Yun Lu <luyun@kylinos.cn> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the changes in commit 581073f626e3 ("af_packet: do not call
packet_read_pending() from tpacket_destruct_skb()"), every time
tpacket_destruct_skb() is executed, the skb_completion is marked as
completed. When wait_for_completion_interruptible_timeout() returns
completed, the pending_refcnt has not yet been reduced to zero.
Therefore, when ph is NULL, the wait function may need to be called
multiple times until packet_read_pending() finally returns zero.
We should call sock_sndtimeo() only once, otherwise the SO_SNDTIMEO
constraint could be way off.
Fixes: 581073f626e3 ("af_packet: do not call packet_read_pending() from tpacket_destruct_skb()") Cc: stable@kernel.org Suggested-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Yun Lu <luyun@kylinos.cn> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LDO5 regulator is used to power the i.MX8MM NVCC_SD2 I/O supply, that is
used for the SD2 card interface and also for some GPIOs.
When the SD card interface is not enabled the regulator subsystem could
turn off this supply, since it is not used anywhere else, however this
will also remove the power to some other GPIOs, for example one I/O that
is used to power the ethernet phy, leading to a non working ethernet
interface.
[ 31.820515] On-module +V3.3_1.8_SD (LDO5): disabling
[ 31.821761] PMIC_USDHC_VSELECT: disabling
[ 32.764949] fec 30be0000.ethernet end0: Link is Down
Fix this keeping the LDO5 supply always on.
Cc: stable@vger.kernel.org Fixes: 6a57f224f734 ("arm64: dts: freescale: add initial support for verdin imx8m mini") Fixes: f5aab0438ef1 ("regulator: pca9450: Fix enable register for LDO5") Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Frank Li <Frank.Li@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new warning in clang [1] points out a place in pep_sock_accept() where
dst is uninitialized then passed as a const pointer to pep_find_pipe():
net/phonet/pep.c:829:37: error: variable 'dst' is uninitialized when passed as a const pointer argument here [-Werror,-Wuninitialized-const-pointer]
829 | newsk = pep_find_pipe(&pn->hlist, &dst, pipe_handle);
| ^~~:
Move the call to pn_skb_get_dst_sockaddr(), which initializes dst, to
before the call to pep_find_pipe(), so that dst is consistently used
initialized throughout the function.
8c8492ca64e7 ("io_uring/net: don't retry connect operation on EPOLLERR")
is a little dirty hack that
1) wrongfully assumes that POLLERR equals to a failed request, which
breaks all POLLERR users, e.g. all error queue recv interfaces.
2) deviates the connection request behaviour from connect(2), and
3) racy and solved at a wrong level.
Nothing can be done with 2) now, and 3) is beyond the scope of the
patch. At least solve 1) by moving the hack out of generic poll handling
into io_connect().
When a module is loaded, it adds trace events defined by the module. It
may also need to modify the modules trace printk formats to replace enum
names with their values.
If two modules are loaded at the same time, the adding of the event to the
ftrace_events list can corrupt the walking of the list in the code that is
modifying the printk format strings and crash the kernel.
The addition of the event should take the trace_event_sem for write while
it adds the new event.
Also add a lockdep_assert_held() on that semaphore in
__trace_add_event_dirs() as it iterates the list.
hid_hw_raw_request() is actually useful to ensure the provided buffer
and length are valid. Directly calling in the low level transport driver
function bypassed those checks and allowed invalid paramto be used.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Closes: https://lore.kernel.org/linux-input/c75433e0-9b47-4072-bbe8-b1d14ea97b13@rowland.harvard.edu/ Cc: stable@vger.kernel.org Link: https://patch.msgid.link/20250710-report-size-null-v2-3-ccf922b7c4e5@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low level transport driver expects the first byte to be the report
ID, even when the report ID is not use (in which case they just shift
the buffer).
However, __hid_request() whas not offsetting the buffer it used by one
in this case, meaning that the raw_request() callback emitted by the
transport driver would be stripped of the first byte.
Note: this changes the API for uhid devices when a request is made
through hid_hw_request. However, several considerations makes me think
this is fine:
- every request to a HID device made through hid_hw_request() would see
that change, but every request made through hid_hw_raw_request()
already has the new behaviour. So that means that the users are
already facing situations where they might have or not the first byte
being the null report ID when it is 0. We are making things more
straightforward in the end.
- uhid is mainly used for BLE devices
- uhid is also used for testing, but I don't see that change a big issue
- for BLE devices, we can check which kernel module is calling
hid_hw_request()
- and in those modules, we can check which are using a Bluetooth device
- and then we can check if the command is used with a report ID or not.
- surprise: none of the kernel module are using a report ID 0
- and finally, bluez, in its function set_report()[0], does the same
shift if the report ID is 0 and the given buffer has a size > 0.
When the report ID is not used, the low level transport drivers expect
the first byte to be 0. However, currently the allocated buffer not
account for that extra byte, meaning that instead of having 8 guaranteed
bytes for implement to be working, we only have 7.
Reported-by: Alan Stern <stern@rowland.harvard.edu> Closes: https://lore.kernel.org/linux-input/c75433e0-9b47-4072-bbe8-b1d14ea97b13@rowland.harvard.edu/ Cc: stable@vger.kernel.org Suggested-by: Alan Stern <stern@rowland.harvard.edu> Link: https://patch.msgid.link/20250710-report-size-null-v2-1-ccf922b7c4e5@kernel.org Signed-off-by: Benjamin Tissoires <bentiss@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma_sync_sg_for_device() functions should be called with the same
nents as the dma_map_sg(), not the value the map function returned
according to the documentation in Documentation/core-api/dma-api.rst:450:
With the sync_sg API, all the parameters must be the same
as those passed into the sg mapping API.
The tb_dp_port_set_hops() function was incorrectly clearing
ADP_DP_CS_1_AUX_RX_HOPID_MASK twice. According to the function's
purpose, it should clear both TX and RX AUX HopID fields. Replace the
first instance with ADP_DP_CS_1_AUX_TX_HOPID_MASK to ensure proper
configuration of both AUX directions.
Fixes: 98176380cbe5 ("thunderbolt: Convert DP adapter register names to follow the USB4 spec") Cc: stable@vger.kernel.org Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the DMA mapping failed, it produced an error log with the wrong
device name:
"stm32-dma3 40400000.dma-controller: rejecting DMA map of vmalloc memory"
Fix this issue by replacing the dev with the I2C dev.
When writing an empty string to either 'qw_sign' or 'landingPage'
sysfs attributes, the store functions attempt to access page[l - 1]
before validating that the length 'l' is greater than zero.
This patch fixes the vulnerability by adding a check at the beginning
of os_desc_qw_sign_store() and webusb_landingPage_store() to handle
the zero-length input case gracefully by returning immediately.
NDI (Northern Digital Inc.) is introducing a new product called the
EMGUIDE GEMINI that will use an FTDI chip for USB serial communications.
Add the NDI EMGUIDE GEMINI product ID that uses the NDI Vendor ID
rather than the FTDI Vendor ID, unlike older products.
Signed-off-by: Ryan Mann <rmann@ndigital.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When transitioning from USB_ROLE_DEVICE to USB_ROLE_NONE, the code
assumed that the regulator should be disabled. However, if the regulator
is marked as always-on, regulator_is_enabled() continues to return true,
leading to an incorrect attempt to disable a regulator which is not
enabled.
This can result in warnings such as:
[ 250.155624] WARNING: CPU: 1 PID: 7326 at drivers/regulator/core.c:3004
_regulator_disable+0xe4/0x1a0
[ 250.155652] unbalanced disables for VIN_SYS_5V0
To fix this, we move the regulator control logic into
tegra186_xusb_padctl_id_override() function since it's directly related
to the ID override state. The regulator is now only disabled when the role
transitions from USB_ROLE_HOST to USB_ROLE_NONE, by checking the VBUS_ID
register. This ensures that regulator enable/disable operations are
properly balanced and only occur when actually transitioning to/from host
mode.
Fixes: 49d46e3c7e59 ("phy: tegra: xusb: Add set_mode support for UTMI phy on Tegra186") Cc: stable@vger.kernel.org Signed-off-by: Wayne Chang <waynec@nvidia.com> Reviewed-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Jon Hunter <jonathanh@nvidia.com> Link: https://lore.kernel.org/r/20250502092606.2275682-1-waynec@nvidia.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rseq_cs field is documented as being set to 0 by user-space prior to
registration, however this is not currently enforced by the kernel. This
can result in a segfault on return to user-space if the value stored in
the rseq_cs field doesn't point to a valid struct rseq_cs.
The correct solution to this would be to fail the rseq registration when
the rseq_cs field is non-zero. However, some older versions of glibc
will reuse the rseq area of previous threads without clearing the
rseq_cs field and will also terminate the process if the rseq
registration fails in a secondary thread. This wasn't caught in testing
because in this case the leftover rseq_cs does point to a valid struct
rseq_cs.
What we can do is clear the rseq_cs field on registration when it's
non-zero which will prevent segfaults on registration and won't break
the glibc versions that reuse rseq areas on thread creation.
Only select ARCH_WANT_HUGE_PMD_SHARE on 64-bit x86.
Page table sharing requires at least three levels because it involves
shared references to PMD tables; 32-bit x86 has either two-level paging
(without PAE) or three-level paging (with PAE), but even with
three-level paging, having a dedicated PGD entry for hugetlb is only
barely possible (because the PGD only has four entries), and it seems
unlikely anyone's actually using PMD sharing on 32-bit.
Having ARCH_WANT_HUGE_PMD_SHARE enabled on non-PAE 32-bit X86 (which
has 2-level paging) became particularly problematic after commit 59d9094df3d7 ("mm: hugetlb: independent PMD page table shared count"),
since that changes `struct ptdesc` such that the `pt_mm` (for PGDs) and
the `pt_share_count` (for PMDs) share the same union storage - and with
2-level paging, PMDs are PGDs.
(For comparison, arm64 also gates ARCH_WANT_HUGE_PMD_SHARE on the
configuration of page tables such that it is never enabled with 2-level
paging.)
Closes: https://lore.kernel.org/r/srhpjxlqfna67blvma5frmy3aa@altlinux.org Fixes: cfe28c5d63d8 ("x86: mm: Remove x86 version of huge_pmd_share.") Reported-by: Vitaly Chikunov <vt@altlinux.org> Suggested-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: Jann Horn <jannh@google.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Acked-by: Oscar Salvador <osalvador@suse.de> Acked-by: David Hildenbrand <david@redhat.com> Tested-by: Vitaly Chikunov <vt@altlinux.org>
Cc:stable@vger.kernel.org Link: https://lore.kernel.org/all/20250702-x86-2level-hugetlb-v2-1-1a98096edf92%40google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assuming the VMM is QEMU. The vq->log_base is from QEMU userpace and can be
reclaimed via gfree(). As a result, this causes invalid memory writes to
QEMU userspace.
The control queue path has the same issue.
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Mike Christie <michael.christie@oracle.com>
Message-Id: <20250403063028.16045-2-dongli.zhang@oracle.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
[ resoloved conflicts in drivers/vhost/scsi.c
bacause vhost_scsi_complete_cmd_work() has been refactored. ] Signed-off-by: Xinyu Zheng <zhengxinyu6@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in
translated mode") not only the getid command is skipped, but also
the de-activating of the keyboard at the end of atkbd_probe(), potentially
re-introducing the problem fixed by commit be2d7e4233a4 ("Input: atkbd -
fix multi-byte scancode handling on reconnect").
Make sure multi-byte scancode handling on reconnect is still handled
correctly by not skipping the atkbd_deactivate() call.
Fixes: 936e4d49ecbc ("Input: atkbd - skip ATKBD_CMD_GETID in translated mode") Tested-by: Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20240126160724.13278-3-hdegoede@redhat.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Chicony Electronics HP 5MP Cameras (USB ID 04F2:B824 & 04F2:B82C)
report a HID sensor interface that is not actually implemented.
Attempting to access this non-functional sensor via iio_info causes
system hangs as runtime PM tries to wake up an unresponsive sensor.
Add these 2 devices to the HID ignore list since the sensor interface is
non-functional by design and should not be exposed to userspace.
MARTLINKTECHNOLOGY is a microphone device, when the HID interface in an
audio device is requested to get specific report id, the following error
may occur.
[ 562.939373] usb 1-1.4.1.2: new full-speed USB device number 21 using xhci_hcd
[ 563.104908] usb 1-1.4.1.2: New USB device found, idVendor=4c4a, idProduct=4155, bcdDevice= 1.00
[ 563.104910] usb 1-1.4.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 563.104911] usb 1-1.4.1.2: Product: USB Composite Device
[ 563.104912] usb 1-1.4.1.2: Manufacturer: SmartlinkTechnology
[ 563.104913] usb 1-1.4.1.2: SerialNumber: 20201111000001
[ 563.229499] input: SmartlinkTechnology USB Composite Device as /devices/pci0000:00/0000:00:07.1/0000:04:00.3/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1.2/1-1.4.1.2:1.2/0003:4C4A:4155.000F/input/input35
[ 563.291505] hid-generic 0003:4C4A:4155.000F: input,hidraw2: USB HID v2.01 Keyboard [SmartlinkTechnology USB Composite Device] on usb-0000:04:00.3-1.4.1.2/input2
[ 563.291557] usbhid 1-1.4.1.2:1.3: couldn't find an input interrupt endpoint
[ 568.506654] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 573.626656] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 578.746657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 583.866655] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
[ 588.986657] usb 1-1.4.1.2: 1:1: usb_set_interface failed (-110)
Ignore HID interface. The device is working properly.
This happens because we are processing an empty block group, which has
no extents allocated from it, there are no items for this block group,
including the block group item since block group items are stored in a
dedicated tree when using the block group tree feature. It also means
this is the block group with the highest start offset, so there are no
higher keys in the extent root, hence btrfs_search_slot_for_read()
returns 1 (no higher key found).
Fix this by asserting 'ret' is 0 only if the block group tree feature
is not enabled, in which case we should find a block group item for
the block group since it's stored in the extent root and block group
item keys are greater than extent item keys (the value for
BTRFS_BLOCK_GROUP_ITEM_KEY is 192 and for BTRFS_EXTENT_ITEM_KEY and
BTRFS_METADATA_ITEM_KEY the values are 168 and 169 respectively).
In case 'ret' is 1, we just need to add a record to the free space
tree which spans the whole block group, and we can achieve this by
making 'ret == 0' as the while loop's condition.
Reported-by: syzbot+36fae25c35159a763a2a@syzkaller.appspotmail.com Link: https://lore.kernel.org/linux-btrfs/6841dca8.a00a0220.d4325.0020.GAE@google.com/ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds DMI-based quirk for the Acer Nitro ANV15-41,
allowing the internal microphone to be detected correctly on
machines with "RB" as board vendor.
When compiling with clang (19.1.7), initializing *vp using a compound
literal may result in excessive stack usage. Fix it by initializing the
required fields of *vp individually.
When transmitting an XDP_REDIRECT packet, call dma_unmap_len_set()
with the proper length instead of 0. This bug triggers this warning
on a system with IOMMU enabled:
In bnxt_ets_validate(), the code incorrectly loops over all possible
traffic classes to check and add the ETS settings. Fix it to loop
over the configured traffic classes only.
The unconfigured traffic classes will default to TSA_ETS with 0
bandwidth. Looping over these unconfigured traffic classes may
cause the validation to fail and trigger this error message:
"rejecting ETS config starving a TC\n"
The .ieee_setets() will then fail.
Fixes: 7df4ae9fe855 ("bnxt_en: Implement DCBNL to support host-based DCBX.") Reviewed-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Shravya KN <shravya.k-n@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Link: https://patch.msgid.link/20250710213938.1959625-2-michael.chan@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The function ll_temac_ethtools_set_ringparam() incorrectly checked
rx_pending twice, once correctly for RX and once mistakenly in place
of tx_pending. This caused tx_pending to be left unchecked against
TX_BD_NUM_MAX.
As a result, invalid TX ring sizes may have been accepted or valid
ones wrongly rejected based on the RX limit, leading to potential
misconfiguration or unexpected results.
This patch corrects the condition to properly validate tx_pending.
Fixes: f7b261bfc35e ("net: ll_temac: Make RX/TX ring sizes configurable") Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com> Link: https://patch.msgid.link/20250710180621.2383000-1-alok.a.tiwari@oracle.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Restrict the 100Mbit forced-mode workaround to link-down transitions
only, to prevent repeated link reset cycles in certain configurations.
The workaround was originally introduced to improve signal reliability
when switching cables between long and short distances. It temporarily
forces the PHY into 10 Mbps before returning to 100 Mbps.
However, when used with autonegotiating link partners (e.g., Intel i350),
executing this workaround on every link change can confuse the partner
and cause constant renegotiation loops. This results in repeated link
down/up transitions and the PHY never reaching a stable state.
Limit the workaround to only run during the PHY_NOLINK state. This ensures
it is triggered only once per link drop, avoiding disruptive toggling
while still preserving its intended effect.
Note: I am not able to reproduce the original issue that this workaround
addresses. I can only confirm that 100 Mbit mode works correctly in my
test setup. Based on code inspection, I assume the workaround aims to
reset some internal state machine or signal block by toggling speeds.
However, a PHY reset is already performed earlier in the function via
phy_init_hw(), which may achieve a similar effect. Without a reproducer,
I conservatively keep the workaround but restrict its conditions.
Fixes: e57cf3639c32 ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250709130753.3994461-3-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous hardcoded definitions of NUM_RX_STATS and
NUM_TX_STATS were not updated when new fields were added
to the ibmvnic_{rx,tx}_queue_stats structures. Specifically,
commit 2ee73c54a615 ("ibmvnic: Add stat for tx direct vs tx
batched") added a fourth TX stat, but NUM_TX_STATS remained 3,
leading to a mismatch.
This patch replaces the static defines with dynamic sizeof-based
calculations to ensure the stat arrays are correctly sized.
This fixes incorrect indexing and prevents incomplete stat
reporting in tools like ethtool.
Fixes: 2ee73c54a615 ("ibmvnic: Add stat for tx direct vs tx batched") Signed-off-by: Mingming Cao <mmc@linux.ibm.com> Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com> Reviewed-by: Haren Myneni <haren@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250709153332.73892-1-mmc@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When updating an existing route entry in atrtr_create(), the old device
reference was not being released before assigning the new device,
leading to a device refcount leak. Fix this by calling dev_put() to
release the old device reference before holding the new one.
Commit 771c994ea51f ("erofs: convert all uncompressed cases to iomap")
converts to use iomap interface, it removed trace_erofs_readpage()
tracepoint in the meantime, let's add it back.
If non-bootstrap bvecs cannot be kept in place (very rarely), an extra
short-lived page is allocated.
Let's just allocate it immediately rather than do unnecessary -EAGAIN
return first and retry as a cleanup. Also it's unnecessary to use
__GFP_NOFAIL here since we could gracefully fail out this case instead.
`end` parameter is no needed since it's pointless for !backmost, we can
handle it with backmost internally. And we only expand the trailing
edge, so the newstart can be replaced with ->headoffset.
Also, remove linux/prefetch.h inclusion since that is not used anymore
after commit 386292919c25 ("erofs: introduce readmore decompression
strategy").
block nbd6: Receive control failed (result -104)
block nbd6: shutting down sockets
==================================================================
BUG: KASAN: slab-use-after-free in recv_work+0x694/0xa80 drivers/block/nbd.c:1022
Write of size 4 at addr ffff8880295de478 by task kworker/u33:0/67
nbd_genl_connect() does not properly stop the device on certain
error paths after nbd_start_device() has been called. This causes
the error path to put nbd->config while recv_work continue to use
the config after putting it, leading to use-after-free in recv_work.
This patch moves nbd_start_device() after the backend file creation.
Reported-by: syzbot+48240bab47e705c53126@syzkaller.appspotmail.com Closes: https://lore.kernel.org/all/68227a04.050a0220.f2294.00b5.GAE@google.com/T/ Fixes: 6497ef8df568 ("nbd: provide a way for userspace processes to identify device backends") Signed-off-by: Zheng Qixing <zhengqixing@huawei.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Link: https://lore.kernel.org/r/20250612132405.364904-1-zhengqixing@huaweicloud.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If raid10_read_request or raid10_write_request registers a new
request and the REQ_NOWAIT flag is set, the code does not
free the malloc from the mempool.
In the raid1_reshape function, newpool is
allocated on the stack and assigned to conf->r1bio_pool.
This results in conf->r1bio_pool.wait.head pointing
to a stack address.
Accessing this address later can lead to a kernel panic.
Example access path:
raid1_reshape()
{
// newpool is on the stack
mempool_t newpool, oldpool;
// initialize newpool.wait.head to stack address
mempool_init(&newpool, ...);
conf->r1bio_pool = newpool;
}
raid1_read_request() or raid1_write_request()
{
alloc_r1bio()
{
mempool_alloc()
{
// if pool->alloc fails
remove_element()
{
--pool->curr_nr;
}
}
}
}
mempool_free()
{
if (pool->curr_nr < pool->min_nr) {
// pool->wait.head is a stack address
// wake_up() will try to access this invalid address
// which leads to a kernel panic
return;
wake_up(&pool->wait);
}
}
Fix:
reinit conf->r1bio_pool.wait after assigning newpool.
There is a potential NULL pointer dereference in zd_mac_tx_to_dev(). For
example, the following is possible:
T0 T1
zd_mac_tx_to_dev()
/* len == skb_queue_len(q) */
while (len > ZD_MAC_MAX_ACK_WAITERS) {
filter_ack()
spin_lock_irqsave(&q->lock, flags);
/* position == skb_queue_len(q) */
for (i=1; i<position; i++)
skb = __skb_dequeue(q)
if (mac->type == NL80211_IFTYPE_AP)
skb = __skb_dequeue(q);
spin_unlock_irqrestore(&q->lock, flags);
skb_dequeue() -> NULL
Since there is a small gap between checking skb queue length and skb being
unconditionally dequeued in zd_mac_tx_to_dev(), skb_dequeue() can return NULL.
Then the pointer is passed to zd_mac_tx_status() where it is dereferenced.
In order to avoid potential NULL pointer dereference due to situations like
above, check if skb is not NULL before passing it to zd_mac_tx_status().
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 459c51ad6e1f ("zd1211rw: port to mac80211") Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru> Link: https://patch.msgid.link/20250626114619.172631-1-d.dulov@aladdin.ru Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When dwc3_gadget_soft_disconnect() fails, dwc3_suspend_common() keeps
going with the suspend, resulting in a period where the power domain is
off, but the gadget driver remains connected. Within this time frame,
invoking vbus_event_work() will cause an error as it attempts to access
DWC3 registers for endpoint disabling after the power domain has been
completely shut down.
Abort the suspend sequence when dwc3_gadget_suspend() cannot halt the
controller and proceeds with a soft connect.
The SSP2 controller has extra endpoint state preserve bit (ESP) which
setting causes that endpoint state will be preserved during
Halt Endpoint command. It is used only for EP0.
Without this bit the Command Verifier "TD 9.10 Bad Descriptor Test"
failed.
Setting this bit doesn't have any impact for SSP controller.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Cc: stable <stable@kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/PH7PR07MB95382CCD50549DABAEFD6156DD7CA@PH7PR07MB9538.namprd07.prod.outlook.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
The uses in this file all seem to assume that data *has been* written!
During the High-Speed Isochronous Audio transfers, xHCI
controller on certain AMD platforms experiences momentary data
loss. This results in Missed Service Errors (MSE) being
generated by the xHCI.
The root cause of the MSE is attributed to the ISOC OUT endpoint
being omitted from scheduling. This can happen when an IN
endpoint with a 64ms service interval either is pre-scheduled
prior to the ISOC OUT endpoint or the interval of the ISOC OUT
endpoint is shorter than that of the IN endpoint. Consequently,
the OUT service is neglected when an IN endpoint with a service
interval exceeding 32ms is scheduled concurrently (every 64ms in
this scenario).
This issue is particularly seen on certain older AMD platforms.
To mitigate this problem, it is recommended to adjust the service
interval of the IN endpoint to not exceed 32ms (interval 8). This
adjustment ensures that the OUT endpoint will not be bypassed,
even if a smaller interval value is utilized.
Enable runtime PM by default for older AMD 1022:43f7 xHCI 1.1 host as it
is proven to work.
Driver enables runtime PM by default for newer xHCI 1.2 host.
In case the removed directory had a snapshot that was deleted, we are
propagating its inode's last_unlink_trans to the parent directory after
we removed the entry from the parent directory. This leaves a small race
window where someone can log the parent directory after we removed the
entry and before we updated last_unlink_trans, and as a result if we ever
try to replay such a log tree, we will fail since we will attempt to
remove a snapshot during log replay, which is currently not possible and
results in the log replay (and mount) to fail. This is the type of failure
described in commit 1ec9a1ae1e30 ("Btrfs: fix unreplayable log after
snapshot delete + parent dir fsync").
So fix this by propagating the last_unlink_trans to the parent directory
before we remove the entry from it.
Fixes: 44f714dae50a ("Btrfs: improve performance on fsync against new inode after rename/unlink") Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Export anon_inode_make_secure_inode() to allow KVM guest_memfd to create
anonymous inodes with proper security context. This replaces the current
pattern of calling alloc_anon_inode() followed by
inode_init_security_anon() for creating security context manually.
This change also fixes a security regression in secretmem where the
S_PRIVATE flag was not cleared after alloc_anon_inode(), causing
LSM/SELinux checks to be bypassed for secretmem file descriptors.
As guest_memfd currently resides in the KVM module, we need to export this
symbol for use outside the core kernel. In the future, guest_memfd might be
moved to core-mm, at which point the symbols no longer would have to be
exported. When/if that happens is still unclear.
Fixes: 2bfe15c52612 ("mm: create security context for memfd_secret inodes") Suggested-by: David Hildenbrand <david@redhat.com> Suggested-by: Mike Rapoport <rppt@kernel.org> Signed-off-by: Shivank Garg <shivankg@amd.com> Link: https://lore.kernel.org/20250620070328.803704-3-shivankg@amd.com Acked-by: "Mike Rapoport (Microsoft)" <rppt@kernel.org> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit under Fixes tightened up the memory accounting for Netlink
sockets. Looks like the accounting is too strict for some existing
use cases, Marek reported issues with nl80211 / WiFi iw CLI.
To reduce number of iterations Netlink dumps try to allocate
messages based on the size of the buffer passed to previous
recvmsg() calls. If user space uses a larger buffer in recvmsg()
than sk_rcvbuf we will allocate an skb we won't be able to queue.
Make sure we always allow at least one skb to be queued.
Same workaround is already present in netlink_attachskb().
Alternative would be to cap the allocation size to
rcvbuf - rmem_alloc
but as I said, the workaround is already present in other places.
If the call of ksmbd_vfs_lock_parent() fails, we drop the parent_path
references and return an error. We need to drop the write access we
just got on parent_path->mnt before we drop the mount reference - callers
assume that ksmbd_vfs_kern_path_locked() returns with mount write
access grabbed if and only if it has returned 0.
Fixes: 864fb5d37163 ("ksmbd: fix possible deadlock in smb2_open") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The qp is created by rdma_create_qp() as t->cm_id->qp
and t->qp is just a shortcut.
rdma_destroy_qp() also calls ib_destroy_qp(cm_id->qp) internally,
but it is protected by a mutex, clears the cm_id and also calls
trace_cm_qp_destroy().
This should make the tracing more useful as both
rdma_create_qp() and rdma_destroy_qp() are traces and it makes
the code look more sane as functions from the same layer are used
for the specific qp object.
trace-cmd stream -e rdma_cma:cm_qp_create -e rdma_cma:cm_qp_destroy
shows this now while doing a mount and unmount from a client:
Cc: Namjae Jeon <linkinjeon@kernel.org> Cc: Steve French <stfrench@microsoft.com> Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Hyunchul Lee <hyc.lee@gmail.com> Cc: Tom Talpey <tom@talpey.com> Cc: linux-cifs@vger.kernel.org Fixes: 0626e6641f6b ("cifsd: add server handler for central processing and tranport layers") Signed-off-by: Stefan Metzmacher <metze@samba.org> Reviewed-by: Tom Talpey <tom@talpey.com> Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After enabling the clocks each error path must disable the clocks again.
One of them failed to do so. Unify the error paths to use goto to make it
harder for future changes to add a similar bug.
Some libc's like musl libc don't provide execinfo.h since it's not part of
POSIX. In order to fix compilation on musl, only include execinfo.h if
available (HAVE_BACKTRACE_SUPPORT)
This was discovered with c104c16073b7 ("Kunit to check the longest symbol
length") which starts to include linux/kallsyms.h with Alpine Linux'
configs.
Link: https://lkml.kernel.org/r/20250622014608.448718-1-fossdd@pwned.life Fixes: c104c16073b7 ("Kunit to check the longest symbol length") Signed-off-by: Achill Gilgenast <fossdd@pwned.life> Cc: Luis Henriques <luis@igalia.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert commit 234f71555019 ("ACPI: battery: negate current when
discharging") breaks not one but several userspace implementations
of battery monitoring: Steam and MangoHud. Perhaps it breaks more,
but those are the two that have been tested.
Reported-by: Matthew Schwartz <matthew.schwartz@linux.dev> Closes: https://lore.kernel.org/linux-acpi/87C1B2AF-D430-4568-B620-14B941A8ABA4@linux.dev/ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A race condition occurs when gs_start_io() calls either gs_start_rx() or
gs_start_tx(), as those functions briefly drop the port_lock for
usb_ep_queue(). This allows gs_close() and gserial_disconnect() to clear
port.tty and port_usb, respectively.
Use the null-safe TTY Port helper function to wake up TTY.
Object creation is a careful dance where we must guarantee that the
object is fully constructed before it is visible to other threads, and
GEM buffer objects are no difference.
Final publishing happens by calling drm_gem_handle_create(). After
that the only allowed thing to do is call drm_gem_object_put() because
a concurrent call to the GEM_CLOSE ioctl with a correctly guessed id
(which is trivial since we have a linear allocator) can already tear
down the object again.
Luckily most drivers get this right, the very few exceptions I've
pinged the relevant maintainers for. Unfortunately we also need
drm_gem_handle_create() when creating additional handles for an
already existing object (e.g. GETFB ioctl or the various bo import
ioctl), and hence we cannot have a drm_gem_handle_create_and_put() as
the only exported function to stop these issues from happening.
Now unfortunately the implementation of drm_gem_handle_create() isn't
living up to standards: It does correctly finishe object
initialization at the global level, and hence is safe against a
concurrent tear down. But it also sets up the file-private aspects of
the handle, and that part goes wrong: We fully register the object in
the drm_file.object_idr before calling drm_vma_node_allow() or
obj->funcs->open, which opens up races against concurrent removal of
that handle in drm_gem_handle_delete().
Fix this with the usual two-stage approach of first reserving the
handle id, and then only registering the object after we've completed
the file-private setup.
Jacek reported this with a testcase of concurrently calling GEM_CLOSE
on a freshly-created object (which also destroys the object), but it
should be possible to hit this with just additional handles created
through import or GETFB without completed destroying the underlying
object with the concurrent GEM_CLOSE ioctl calls.
Note that the close-side of this race was fixed in f6cd7daecff5 ("drm:
Release driver references to handle before making it available
again"), which means a cool 9 years have passed until someone noticed
that we need to make this symmetry or there's still gaps left :-/
Without the 2-stage close approach we'd still have a race, therefore
that's an integral part of this bugfix.
More importantly, this means we can have NULL pointers behind
allocated id in our drm_file.object_idr. We need to check for that
now:
- drm_gem_handle_delete() checks for ERR_OR_NULL already
- drm_gem.c:object_lookup() also chekcs for NULL
- drm_gem_release() should never be called if there's another thread
still existing that could call into an IOCTL that creates a new
handle, so cannot race. For paranoia I added a NULL check to
drm_gem_object_release_handle() though.
- most drivers (etnaviv, i915, msm) are find because they use
idr_find(), which maps both ENOENT and NULL to NULL.
- drivers using idr_for_each_entry() should also be fine, because
idr_get_next does filter out NULL entries and continues the
iteration.
- The same holds for drm_show_memory_stats().
v2: Use drm_WARN_ON (Thomas)
Reported-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Tested-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Cc: stable@vger.kernel.org Cc: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <mripard@kernel.org> Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: David Airlie <airlied@gmail.com> Cc: Simona Vetter <simona@ffwll.ch> Signed-off-by: Simona Vetter <simona.vetter@intel.com> Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20250707151814.603897-1-simona.vetter@ffwll.ch Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A small race exists between spsc_queue_push and the run-job worker, in
which spsc_queue_push may return not-first while the run-job worker has
already idled due to the job count being zero. If this race occurs, job
scheduling stops, leading to hangs while waiting on the job’s DMA
fences.
Seal this race by incrementing the job count before appending to the
SPSC queue.
This race was observed on a drm-tip 6.16-rc1 build with the Xe driver in
an SVM test case.
Fixes: 1b1f42d8fde4 ("drm: move amd_gpu_scheduler into common location") Fixes: 27105db6c63a ("drm/amdgpu: Add SPSC queue to scheduler.") Cc: stable@vger.kernel.org Signed-off-by: Matthew Brost <matthew.brost@intel.com> Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com> Link: https://lore.kernel.org/r/20250613212013.719312-1-matthew.brost@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is a mitigation to prevent the A-MSDU spoofing vulnerability
for mesh networks. The initial update to the IEEE 802.11 standard, in
response to the FragAttacks, missed this case (CVE-2025-27558). It can
be considered a variant of CVE-2020-24588 but for mesh networks.
This patch tries to detect if a standard MSDU was turned into an A-MSDU
by an adversary. This is done by parsing a received A-MSDU as a standard
MSDU, calculating the length of the Mesh Control header, and seeing if
the 6 bytes after this header equal the start of an rfc1042 header. If
equal, this is a strong indication of an ongoing attack attempt.
This defense was tested with mac80211_hwsim against a mesh network that
uses an empty Mesh Address Extension field, i.e., when four addresses
are used, and when using a 12-byte Mesh Address Extension field, i.e.,
when six addresses are used. Functionality of normal MSDUs and A-MSDUs
was also tested, and confirmed working, when using both an empty and
12-byte Mesh Address Extension field.
It was also tested with mac80211_hwsim that A-MSDU attacks in non-mesh
networks keep being detected and prevented.
Note that the vulnerability being patched, and the defense being
implemented, was also discussed in the following paper and in the
following IEEE 802.11 presentation:
On some platforms, the UFS-reset pin has no interrupt logic in TLMM but
is nevertheless registered as a GPIO in the kernel. This enables the
user-space to trigger a BUG() in the pinctrl-msm driver by running, for
example: `gpiomon -c 0 113` on RB2.
The exact culprit is requesting pins whose intr_detection_width setting
is not 1 or 2 for interrupts. This hits a BUG() in
msm_gpio_irq_set_type(). Potentially crashing the kernel due to an
invalid request from user-space is not optimal, so let's go through the
pins and mark those that would fail the check as invalid for the irq chip
as we should not even register them as available irqs.
This function can be extended if we determine that there are more
corner-cases like this.
Use addrconf_add_dev() instead of ipv6_find_idev() in
addrconf_gre_config() so that we don't just get the inet6_dev, but also
install the default ff00::/8 multicast route.
Before commit 3e6a0243ff00 ("gre: Fix again IPv6 link-local address
generation."), the multicast route was created at the end of the
function by addrconf_add_mroute(). But this code path is now only taken
in one particular case (gre devices not bound to a local IP address and
in EUI64 mode). For all other cases, the function exits early and
addrconf_add_mroute() is not called anymore.
Using addrconf_add_dev() instead of ipv6_find_idev() in
addrconf_gre_config(), fixes the problem as it will create the default
multicast route for all gre devices. This also brings
addrconf_gre_config() a bit closer to the normal netdevice IPv6
configuration code (addrconf_dev_config()).
Cc: stable@vger.kernel.org Fixes: 3e6a0243ff00 ("gre: Fix again IPv6 link-local address generation.") Reported-by: Aiden Yang <ling@moedove.com> Closes: https://lore.kernel.org/netdev/CANR=AhRM7YHHXVxJ4DmrTNMeuEOY87K2mLmo9KMed1JMr20p6g@mail.gmail.com/ Reviewed-by: Gary Guo <gary@garyguo.net> Tested-by: Gary Guo <gary@garyguo.net> Signed-off-by: Guillaume Nault <gnault@redhat.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://patch.msgid.link/027a923dcb550ad115e6d93ee8bb7d310378bd01.1752070620.git.gnault@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reject migration of SEV{-ES} state if either the source or destination VM
is actively creating a vCPU, i.e. if kvm_vm_ioctl_create_vcpu() is in the
section between incrementing created_vcpus and online_vcpus. The bulk of
vCPU creation runs _outside_ of kvm->lock to allow creating multiple vCPUs
in parallel, and so sev_info.es_active can get toggled from false=>true in
the destination VM after (or during) svm_vcpu_create(), resulting in an
SEV{-ES} VM effectively having a non-SEV{-ES} vCPU.
The issue manifests most visibly as a crash when trying to free a vCPU's
NULL VMSA page in an SEV-ES VM, but any number of things can go wrong.
Deliberately don't check for a NULL VMSA when freeing the vCPU, as crashing
the host is likely desirable due to the VMSA being consumed by hardware.
E.g. if KVM manages to allow VMRUN on the vCPU, hardware may read/write a
bogus VMSA page. Accessing PFN 0 is "fine"-ish now that it's sequestered
away thanks to L1TF, but panicking in this scenario is preferable to
potentially running with corrupted state.
Reported-by: Alexander Potapenko <glider@google.com> Tested-by: Alexander Potapenko <glider@google.com> Fixes: 0b020f5af092 ("KVM: SEV: Add support for SEV-ES intra host migration") Fixes: b56639318bb2 ("KVM: SEV: Add support for SEV intra host migration") Cc: stable@vger.kernel.org Cc: James Houghton <jthoughton@google.com> Cc: Peter Gonda <pgonda@google.com> Reviewed-by: Liam Merwick <liam.merwick@oracle.com> Tested-by: Liam Merwick <liam.merwick@oracle.com> Reviewed-by: James Houghton <jthoughton@google.com> Link: https://lore.kernel.org/r/20250602224459.41505-2-seanjc@google.com Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid imposing an ordering constraint on userspace, allow 'invalid'
event channel targets to be configured in the IRQ routing table.
This is the same as accepting interrupts targeted at vCPUs which don't
exist yet, which is already the case for both Xen event channels *and*
for MSIs (which don't do any filtering of permitted APIC ID targets at
all).
If userspace actually *triggers* an IRQ with an invalid target, that
will fail cleanly, as kvm_xen_set_evtchn_fast() also does the same range
check.
If KVM enforced that the IRQ target must be valid at the time it is
*configured*, that would force userspace to create all vCPUs and do
various other parts of setup (in this case, setting the Xen long_mode)
before restoring the IRQ table.
Cc: stable@vger.kernel.org Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Paul Durrant <paul@xen.org> Link: https://lore.kernel.org/r/e489252745ac4b53f1f7f50570b03fb416aa2065.camel@infradead.org
[sean: massage comment] Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CMCI banks are not cleared during shutdown on Intel CPUs. As a side effect,
when a kexec is performed, CPUs coming back online are unable to
rediscover/claim these occupied banks which breaks MCE reporting.
Clear the CPU ownership during shutdown via cmci_clear() so the banks can
be reclaimed and MCE reporting will become functional once more.
Currently, the MCE subsystem sysfs interface will be removed if the
thresholding sysfs interface fails to be created. A common failure is due to
new MCA bank types that are not recognized and don't have a short name set.
The MCA thresholding feature is optional and should not break the common MCE
sysfs interface. Also, new MCA bank types are occasionally introduced, and
updates will be needed to recognize them. But likewise, this should not break
the common sysfs interface.
Keep the MCE sysfs interface regardless of the status of the thresholding
sysfs interface.
The MCA threshold limit must be reset after servicing the interrupt.
Currently, the restart function doesn't have an explicit check for this. It
makes some assumptions based on the current limit and what's in the registers.
These assumptions don't always hold, so the limit won't be reset in some
cases.
Make the reset condition explicit. Either an interrupt/overflow has occurred
or the bank is being initialized.
The "intf" list iterator is an invalid pointer if the correct
"intf->intf_num" is not found. Calling atomic_dec(&intf->nr_users) on
and invalid pointer will lead to memory corruption.
We don't really need to call atomic_dec() if we haven't called
atomic_add_return() so update the if (intf->in_shutdown) path as well.
Fixes: 8e76741c3d8b ("ipmi: Add a limit on the number of users that may use IPMI") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Message-ID: <aBjMZ8RYrOt6NOgi@stanley.mountain> Signed-off-by: Corey Minyard <corey@minyard.net>
[ - Dropped change to the `if (intf->in_shutdown)` block since that logic
doesn't exist yet.
- Modified out_unlock to release the srcu lock instead of the mutex
since we don't have the mutex here yet. ] Signed-off-by: Brendan Jackman <jackmanb@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an AF_RXRPC service socket is opened and bound, but calls are
preallocated, then rxrpc_alloc_incoming_call() will oops because the
rxrpc_backlog struct doesn't get allocated until the first preallocation is
made.
Fix this by returning NULL from rxrpc_alloc_incoming_call() if there is no
backlog struct. This will cause the incoming call to be aborted.
Temporarily clear the preallocation flag when explicitly requesting
allocations. Pre-existing allocations are already counted against the
request through mas_node_count_gfp(), but the allocations will not happen
if the MA_STATE_PREALLOC flag is set. This flag is meant to avoid
re-allocating in bulk allocation mode, and to detect issues with
preallocation calculations.
The MA_STATE_PREALLOC flag should also always be set on zero allocations
so that detection of underflow allocations will print a WARN_ON() during
consumption.
User visible effect of this flaw is a WARN_ON() followed by a null pointer
dereference when subsequent requests for larger number of nodes is
ignored, such as the vma merge retry in mmap_region() caused by drivers
altering the vma flags (which happens in v6.6, at least)
Lion's patch [1] revealed an ancient bug in the qdisc API.
Whenever a user creates/modifies a qdisc specifying as a parent another
qdisc, the qdisc API will, during grafting, detect that the user is
not trying to attach to a class and reject. However grafting is
performed after qdisc_create (and thus the qdiscs' init callback) is
executed. In qdiscs that eventually call qdisc_tree_reduce_backlog
during init or change (such as fq, hhf, choke, etc), an issue
arises. For example, executing the following commands:
sudo tc qdisc add dev lo root handle a: htb default 2
sudo tc qdisc add dev lo parent a: handle beef fq
Qdiscs such as fq, hhf, choke, etc unconditionally invoke
qdisc_tree_reduce_backlog() in their control path init() or change() which
then causes a failure to find the child class; however, that does not stop
the unconditional invocation of the assumed child qdisc's qlen_notify with
a null class. All these qdiscs make the assumption that class is non-null.
The solution is ensure that qdisc_leaf() which looks up the parent
class, and is invoked prior to qdisc_create(), should return failure on
not finding the class.
In this patch, we leverage qdisc_leaf to return ERR_PTRs whenever the
parentid doesn't correspond to a class, so that we can detect it
earlier on and abort before qdisc_create is called.
This happens if we call ioctl(ATMARP_MKIP) more than once.
During the first call, clip_mkip() sets clip_push() to vcc->push(),
and the second call copies it to clip_vcc->old_push().
Later, when the socket is close()d, vcc_destroy_socket() passes
NULL skb to clip_push(), which calls clip_vcc->old_push(),
triggering the infinite recursion.
Let's prevent the second ioctl(ATMARP_MKIP) by checking
vcc->user_back, which is allocated by the first call as clip_vcc.
Note also that we use lock_sock() to prevent racy calls.
Force a fixed MDI-X mode when auto-negotiation is disabled to prevent
link instability.
When forcing the link speed and duplex on a LAN9500 PHY (e.g., with
`ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto
mode, the PHY fails to establish a stable link. This occurs because the
PHY's Auto-MDIX algorithm is not designed to operate when
auto-negotiation is disabled. In this state, the PHY continuously
toggles the TX/RX signal pairs, which prevents the link partner from
synchronizing.
This patch resolves the issue by detecting when auto-negotiation is
disabled. If the MDI-X control mode is set to 'auto', the driver now
forces a specific, stable mode (ETH_TP_MDI) to prevent the pair
toggling. This choice of a fixed MDI mode mirrors the behavior the
hardware would exhibit if the AUTOMDIX_EN strap were configured for a
fixed MDI connection.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: Andre Edich <andre.edich@microchip.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9a1 ("smsc95xx: add phylib support") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: Andre Edich <andre.edich@microchip.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Support returning VMADDR_CID_LOCAL in case no other vsock transport is
available.
Fixes: 0e12190578d0 ("vsock: add local transport support in the vsock core") Suggested-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Michal Luczaj <mhal@rbox.co> Link: https://patch.msgid.link/20250703-vsock-transports-toctou-v4-3-98f0eb530747@rbox.co Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
