This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released evaluates against the
released altmode's partner instead of the calling altmode itself, so change
adev in typec_altmode_put_partner to properly refer to the altmode being
released.
typec_altmode_set_partner is not run for port altmodes, so also add a check
in typec_altmode_release to prevent typec_altmode_put_partner() calls on
port altmode release.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes") Cc: stable@vger.kernel.org Signed-off-by: RD Babiera <rdbabiera@google.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20231129192349.1773623-2-rdbabiera@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling runtime pm as default for all AMD xHC 1.1 controllers caused
regression. An initial attempt to fix those was done in commit a5d6264b638e
("xhci: Enable RPM on controllers that support low-power states") but new
issues are still seen.
Revert this to get those AMD xHC 1.1 systems working
This patch went to stable an needs to be reverted from there as well.
Deduplication isn't supported on cifs, but cifs doesn't reject it, instead
treating it as extent duplication/cloning. This can cause generic/304 to go
silly and run for hours on end.
Fix cifs to indicate EOPNOTSUPP if REMAP_FILE_DEDUP is set in
->remap_file_range().
Note that it's unclear whether or not commit b073a08016a1 is meant to cause
cifs to return an error if REMAP_FILE_DEDUP.
Fixes: b073a08016a1 ("cifs: fix that return -EINVAL when do dedupe operation") Cc: stable@vger.kernel.org Suggested-by: Dave Chinner <david@fromorbit.com>
cc: Xiaoli Feng <fengxiaoli0714@gmail.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Darrick Wong <darrick.wong@oracle.com>
cc: fstests@vger.kernel.org
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org Link: https://lore.kernel.org/r/3876191.1701555260@warthog.procyon.org.uk/ Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 89ff3dfac604 ("usb: gadget: f_hid: fix f_hidg lifetime vs
cdev") has introduced a bug that leads to hid device corruption after
the replug operation.
Reverse device managed memory allocation for the report descriptor
to fix the issue.
Tested:
This change was tested on the AMD EthanolX CRB server with the BMC
based on the OpenBMC distribution. The BMC provides KVM functionality
via the USB gadget device:
- before: KVM page refresh results in a broken USB device,
- after: KVM page refresh works without any issues.
All chips that support RAS also support IP discovery, so
use the IP versions rather than a mix of IP versions and
asic types. Checking the validity of the atom_ctx pointer
is not required as the vbios is already fetched at this
point.
v2: add comments to id asic types based on feedback from Luben
As soon as control->i2c_address is set, return; remove the "break;" from the
switch--it is unnecessary. This mimics what happens when for some cases in the
switch, we call helper functions with "return <helper function>".
Remove final function "return true;" to indicate that the switch is final and
terminal, and that there should be no code after the switch.
Cc: Candice Li <candice.li@amd.com> Cc: Kent Russell <kent.russell@amd.com> Cc: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e0409021e34a ("drm/amdgpu: Update EEPROM I2C address for smu v13_0_0") Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove second switch since it already has its own function and case in the
first switch. This also avoids requalifying the EEPROM I2C address for VEGA20,
SIENNA CICHLID, and ALDEBARAN, as those have been set by the first switch and
shouldn't match SMU v13.0.x.
Cc: Candice Li <candice.li@amd.com> Cc: Kent Russell <kent.russell@amd.com> Cc: Alex Deucher <Alexander.Deucher@amd.com> Fixes: 158225294683 ("drm/amdgpu: Add EEPROM I2C address for smu v13_0_0") Fixes: c9bdc6c3cf39 ("drm/amdgpu: Add EEPROM I2C address support for ip discovery") Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e0409021e34a ("drm/amdgpu: Update EEPROM I2C address for smu v13_0_0") Signed-off-by: Sasha Levin <sashal@kernel.org>
Add support for RAS table at I2C EEPROM address of 0x40000, since on some
ASICs it is not at 0, but at 0x40000.
Cc: Alex Deucher <Alexander.Deucher@amd.com> Cc: Kent Russell <kent.russell@amd.com> Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Tested-by: Kent Russell <kent.russell@amd.com> Reviewed-by: Kent Russell <kent.russell@amd.com> Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e0409021e34a ("drm/amdgpu: Update EEPROM I2C address for smu v13_0_0") Signed-off-by: Sasha Levin <sashal@kernel.org>
Abstract RAS I2C EEPROM addresses from chip names, and set their macro
definition names to the address they set, not the chip they attach
to. Since most chips either use I2C EEPROM address 0 or 40000h for the RAS
table start offset, this leaves us with only two macro definitions as
opposed to five, and removes the redundancy of four.
Cc: Candice Li <candice.li@amd.com> Cc: Tao Zhou <tao.zhou1@amd.com> Cc: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Kent Russell <kent.russell@amd.com> Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e0409021e34a ("drm/amdgpu: Update EEPROM I2C address for smu v13_0_0") Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove redundant EEPROM_I2C_MADDR_54H address, since we already have it
represented (ARCTURUS), and since we don't include the I2C device type
identifier in EEPROM memory addresses, i.e. that high up in the device
abstraction--we only use EEPROM memory addresses, as memory is continuously
represented by EEPROM device(s) on the I2C bus.
Add a comment describing what these memory addresses are, how they come
about and how they're usually extracted from the device address byte.
Cc: Candice Li <candice.li@amd.com> Cc: Tao Zhou <tao.zhou1@amd.com> Cc: Alex Deucher <Alexander.Deucher@amd.com> Fixes: c9bdc6c3cf39df ("drm/amdgpu: Add EEPROM I2C address support for ip discovery") Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e0409021e34a ("drm/amdgpu: Update EEPROM I2C address for smu v13_0_0") Signed-off-by: Sasha Levin <sashal@kernel.org>
WARNING: Block comments use * on subsequent lines
WARNING: Block comments use a trailing */ on a separate line
WARNING: suspect code indent for conditional statements (8, 12)
WARNING: braces {} are not necessary for single statement blocks
Cc: Christian König <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: c6df7f313794 ("drm/amdgpu: correct the amdgpu runtime dereference usage count") Signed-off-by: Sasha Levin <sashal@kernel.org>
If gpio_set_transitory() fails, we should free the GPIO again. Most
notably, the flag FLAG_REQUESTED has previously been set in
gpiod_request_commit(), and should be reset on failure.
To my knowledge, this does not affect any current users, since the
gpio_set_transitory() mainly returns 0 and -ENOTSUPP, which is converted
to 0. However the gpio_set_transitory() function calles the .set_config()
function of the corresponding GPIO chip and there are some GPIO drivers in
which some (unlikely) branches return other values like -EPROBE_DEFER,
and -EINVAL. In these cases, the above mentioned FLAG_REQUESTED would not
be reset, which results in the pin being blocked until the next reboot.
A write-access violation page fault kernel crash was observed while running
cpuhotplug LTP testcases on SEV-ES enabled systems. The crash was
observed during hotplug, after the CPU was offlined and the process
was migrated to different CPU. setup_ghcb() is called again which
tries to update ghcb_version in sev_es_negotiate_protocol(). Ideally this
is a read_only variable which is initialised during booting.
Budimir noted that perf_event_validate_size() only checks the size of
the newly added event, even though the sizes of all existing events
can also change due to not all events having the same read_format.
When we attach the new event, perf_group_attach(), we do re-compute
the size for all events.
Enable GENERIC_BUG_RELATIVE_POINTERS which will store 32-bit relative
offsets to the bug address and the source file name instead of 64-bit
absolute addresses. This effectively reduces the size of the
bug_table[] array by half on 64-bit kernels.
Signed-off-by: Helge Deller <deller@gmx.de>
Stable-dep-of: 487635756198 ("parisc: Fix asm operand number out of range build error in bug table") Signed-off-by: Sasha Levin <sashal@kernel.org>
When the ring buffer is being resized, it can cause side effects to the
running tracer. For instance, there's a race with irqsoff tracer that
swaps individual per cpu buffers between the main buffer and the snapshot
buffer. The resize operation modifies the main buffer and then the
snapshot buffer. If a swap happens in between those two operations it will
break the tracer.
Simply stop the running tracer before resizing the buffers and enable it
again when finished.
Link: https://lkml.kernel.org/r/20231205220010.748996423@goodmis.org Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 3928a8a2d9808 ("ftrace: make work with new ring buffer") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we can resize trace ringbuffer by writing a value into file
'buffer_size_kb', then by reading the file, we get the value that is
usually what we wrote. However, this value may be not actual size of
trace ring buffer because of the round up when doing resize in kernel,
and the actual size would be more useful.
There's a race where if an event is discarded from the ring buffer and an
interrupt were to happen at that time and insert an event, the time stamp
is still used from the discarded event as an offset. This can screw up the
timings.
If the event is going to be discarded, set the "before_stamp" to zero.
When a new event comes in, it compares the "before_stamp" with the
"write_stamp" and if they are not equal, it will insert an absolute
timestamp. This will prevent the timings from getting out of sync due to
the discarded event.
Link: https://lore.kernel.org/linux-trace-kernel/20231206100244.5130f9b3@gandalf.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 6f6be606e763f ("ring-buffer: Force before_stamp and write_stamp to be different on discard") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The pointer returned is later signed-extended to 0xfffffffffc00b480 at
`BPF_JMP | BPF_EXIT`. During BPF prog run, this triggers unhandled page
fault and a kernel panic.
Drop the unnecessary signed-extension on return values like other
architectures do.
The expression `task->cgroups->dfl_cgrp` involves two memory load.
Since the field offset fits in imm12 or imm14, we use ldd or ldptrd
instructions. But both instructions have the side effect that it will
signed-extended the imm operand. Finally, we got the wrong addresses
and panics is inevitable.
Use a generic ldxd instruction to avoid this kind of issues.
Clang static analyzer complains that value stored to 'rets' is never
read.Let 'buf_len = -EOVERFLOW' to make sure we can return '-EOVERFLOW'.
Fixes: 8c8d964ce90f ("mei: move hbuf_depth from the mei device to the hw modules") Signed-off-by: Su Hui <suhui@nfschina.com> Link: https://lore.kernel.org/r/20231120095523.178385-2-suhui@nfschina.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When start trace with perf option "-C $cpu" and immediately stop it
with SIGTERM or others, the perf core will invoke pmu::read() while
the driver doesn't implement it. Add a dummy pmu::read() to avoid
any issues.
Fixes: ff0de066b463 ("hwtracing: hisi_ptt: Add trace function support for HiSilicon PCIe Tune and Trace device") Signed-off-by: Junhao He <hejunhao3@huawei.com> Signed-off-by: Yicong Yang <yangyicong@hisilicon.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20231010084731.30450-6-yangyicong@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
etm4_platform_driver (which lives in ".data" contains a reference to
etm4_remove_platform_dev(). So the latter must not be marked with __exit
which results in the function being discarded for a build with
CONFIG_CORESIGHT_SOURCE_ETM4X=y which in turn makes the remove pointer
contain invalid data.
etm4x_amba_driver referencing etm4_remove_amba() has the same issue.
Drop the __exit annotations for the two affected functions and a third
one that is called by the other two.
For reasons I don't understand this isn't catched by building with
CONFIG_DEBUG_SECTION_MISMATCH=y.
etm4_remove_dev() returned zero unconditionally. Make it return void
instead, which makes it clear in the callers that there is no error to
handle. Simplify etm4_remove_platform_dev() accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20230518201629.260672-1-u.kleine-koenig@pengutronix.de
Stable-dep-of: 348ddab81f7b ("coresight: etm4x: Remove bogous __exit annotation for some functions") Signed-off-by: Sasha Levin <sashal@kernel.org>
A transaction complete work is allocated and queued for each
transaction. Under certain conditions the work->type might be marked as
BINDER_WORK_TRANSACTION_ONEWAY_SPAM_SUSPECT to notify userspace about
potential spamming threads or as BINDER_WORK_TRANSACTION_PENDING when
the target is currently frozen.
However, these work types are not being handled in binder_release_work()
so they will leak during a cleanup. This was reported by syzkaller with
the following kmemleak dump:
The NTC is defined as ntc@0 but it doesn't need any address at all.
Fix the unit_address_vs_reg warning by dropping the unit address: since
the node name has to be generic also fully rename it from ntc@0 to
thermal-sensor.
The reserved memory for scp had node name "scp_mem_region" and also
without unit-address: change the name to "memory@(address)".
This fixes a unit_address_vs_reg warning.
Before suspending the LARBs we're making sure that any operation is
done: this never happens because we are unexpectedly unclocking the
LARB20 before executing the suspend handler for the MediaTek Smart
Multimedia Interface (SMI) and the cause of this is incorrect clocks
on this LARB.
Fix this issue by changing the Local Arbiter 20 (used by the video
encoder secondary core) apb clock to CLK_VENC_CORE1_VENC;
furthermore, in order to make sure that both the PM resume and video
encoder operation is stable, add the CLK_VENC(_CORE1)_LARB clock to
the VENC (main core) and VENC_CORE1 power domains, as this IP cannot
communicate with the rest of the system (the AP) without local
arbiter clocks being operational.
Cc: stable@vger.kernel.org Fixes: 3b5838d1d82e ("arm64: dts: mt8195: Add iommu and smi nodes") Fixes: 2b515194bf0c ("arm64: dts: mt8195: Add power domains controller") Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com> Link: https://lore.kernel.org/r/20230706095841.109315-1-angelogioacchino.delregno@collabora.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a unit_address_vs_reg warning for the USB VBUS fixed regulators
by renaming the regulator nodes from regulator@{0,1} to regulator-usb-p0
and regulator-usb-p1.
dtbs_check throws a warning at the dsi node:
Warning (avoid_unnecessary_addr_size): /soc/dsi@14014000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Other DTS have a panel child node with a reg, so the parent dtsi
must have the address-cells and size-cells, however this specific DT
has the panel removed, but not the cells, hence the warning above.
If panel is deleted then the cells must also be deleted since they are
tied together, as the child node in this DT does not have a reg.
Cc: stable@vger.kernel.org Fixes: cabc71b08eb5 ("arm64: dts: mt8183: Add kukui-jacuzzi-damu board") Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20230814071053.5459-1-eugen.hristev@collabora.com Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a reshape or a RAID6 array such as expanding by adding an additional
disk, I/Os to the region of the array which have not yet been reshaped can
stall indefinitely. This is from errors in the stripe_ahead_of_reshape
function causing md to think the I/O is to a region in the actively
undergoing the reshape.
stripe_ahead_of_reshape fails to account for the q disk having a sector
value of 0. By not excluding the q disk from the for loop, raid6 will always
generate a min_sector value of 0, causing a return value which stalls.
The function's max_sector calculation also uses min() when it should use
max(), causing the max_sector value to always be 0. During a backwards
rebuild this can cause the opposite problem where it allows I/O to advance
when it should wait.
Fixing these errors will allow safe I/O to advance in a timely manner and
delay only I/O which is unsafe due to stripes in the middle of undergoing
the reshape.
Fixes: 486f60558607 ("md/raid5: Check all disks in a stripe_head for reshape progress") Cc: stable@vger.kernel.org # v6.0+ Signed-off-by: David Jeffery <djeffery@redhat.com> Tested-by: Laurence Oberman <loberman@redhat.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20231128181233.6187-1-djeffery@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The policy returned by cpufreq_cpu_get() has to be released with
the help of cpufreq_cpu_put() to balance its kobject reference counter
properly.
Add the missing calls to cpufreq_cpu_put() in the code.
Fixes: 0aea2e4ec2a2 ("powercap/dtpm_cpu: Reset per_cpu variable in the release function") Fixes: 0e8f68d7f048 ("powercap/drivers/dtpm: Add CPU energy model based support") Cc: v5.16+ <stable@vger.kernel.org> # v5.16+ Signed-off-by: Lukasz Luba <lukasz.luba@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reports oops in lockdep's __lock_acquire(), called from
__pte_offset_map_lock() called from filemap_map_pages(); or when I run the
repro, the oops comes in pmd_install(), called from filemap_map_pmd()
called from filemap_map_pages(), just before the __pte_offset_map_lock().
The problem is that filemap_map_pmd() has been assuming that when it finds
pmd_none(), a page table has already been prepared in prealloc_pte; and
indeed do_fault_around() has been careful to preallocate one there, when
it finds pmd_none(): but what if *pmd became none in between?
My 6.6 mods in mm/khugepaged.c, avoiding mmap_lock for write, have made it
easy for *pmd to be cleared while servicing a page fault; but even before
those, a huge *pmd might be zapped while a fault is serviced.
The difference in symptomatic stack traces comes from the "memory model"
in use: pmd_install() uses pmd_populate() uses page_to_pfn(): in some
models that is strict, and will oops on the NULL prealloc_pte; in other
models, it will construct a bogus value to be populated into *pmd, then
__pte_offset_map_lock() oops when trying to access split ptlock pointer
(or some other symptom in normal case of ptlock embedded not pointer).
Link: https://lore.kernel.org/linux-mm/20231115065506.19780-1-jose.pekkarinen@foxhound.fi/ Link: https://lkml.kernel.org/r/6ed0c50c-78ef-0719-b3c5-60c0c010431c@google.com Fixes: f9ce0be71d1f ("mm: Cleanup faultaround and finish_fault() codepaths") Signed-off-by: Hugh Dickins <hughd@google.com> Reported-and-tested-by: syzbot+89edd67979b52675ddec@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-mm/0000000000005e44550608a0806c@google.com/ Reviewed-by: David Hildenbrand <david@redhat.com> Cc: Jann Horn <jannh@google.com>, Cc: José Pekkarinen <jose.pekkarinen@foxhound.fi> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> [5.12+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The routine __vma_private_lock tests for the existence of a reserve map
associated with a private hugetlb mapping. A pointer to the reserve map
is in vma->vm_private_data. __vma_private_lock was checking the pointer
for NULL. However, it is possible that the low bits of the pointer could
be used as flags. In such instances, vm_private_data is not NULL and not
a valid pointer. This results in the null-ptr-deref reported by syzbot:
Mask off low bit flags before checking for NULL pointer. In addition, the
reserve map only 'belongs' to the OWNER (parent in parent/child
relationships) so also check for the OWNER flag.
Link: https://lkml.kernel.org/r/20231114012033.259600-1-mike.kravetz@oracle.com Reported-by: syzbot+6ada951e7c0f7bc8a71e@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-mm/00000000000078d1e00608d7878b@google.com/ Fixes: bf4916922c60 ("hugetlbfs: extend hugetlb_vma_lock to private VMAs") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Rik van Riel <riel@surriel.com> Cc: Edward Adam Davis <eadavis@qq.com> Cc: Muchun Song <muchun.song@linux.dev> Cc: Nathan Chancellor <nathan@kernel.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Tom Rix <trix@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Serdev recv_buf() callback is supposed to return the amount of bytes
consumed, therefore an int in between 0 and count.
Do not return negative number in case of issue, when
ssam_controller_receive_buf() returns ESHUTDOWN just returns 0, e.g. no
bytes consumed, this keep the exact same behavior as it was before.
This fixes a potential WARN in serdev-ttyport.c:ttyport_receive_buf().
Fixes: c167b9c7e3d6 ("platform/surface: Add Surface Aggregator subsystem") Cc: stable@vger.kernel.org Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20231128194935.11350-1-francesco@dolcini.it Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 0ec7731655de ("regmap: Ensure range selector registers
are updated after cache sync") opening pcm512x based soundcards fail
with EINVAL and dmesg shows sync cache and pm_runtime_get errors:
[ 228.794676] pcm512x 1-004c: Failed to sync cache: -22
[ 228.794740] pcm512x 1-004c: ASoC: error at snd_soc_pcm_component_pm_runtime_get on pcm512x.1-004c: -22
This is caused by the cache check result leaking out into the
regcache_sync return value.
Fix this by making the check local-only, as the comment above the
regcache_read call states a non-zero return value means there's
nothing to do so the return value should not be altered.
Fixes: 0ec7731655de ("regmap: Ensure range selector registers are updated after cache sync") Cc: stable@vger.kernel.org Signed-off-by: Matthias Reichl <hias@horus.com> Link: https://lore.kernel.org/r/20231203222216.96547-1-hias@horus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When FIFO reaches near full state, device will issue pause frame.
If pause slot is enabled(set to 1), in this time, device will issue
pause frame only once. But if pause slot is disabled(set to 0), device
will keep sending pause frames until FIFO reaches near empty state.
When pause slot is disabled, if there is no one to handle receive
packets, device FIFO will reach near full state and keep sending
pause frames. That will impact entire local area network.
This issue can be reproduced in Chromebox (not Chromebook) in
developer mode running a test image (and v5.10 kernel):
1) ping -f $CHROMEBOX (from workstation on same local network)
2) run "powerd_dbus_suspend" from command line on the $CHROMEBOX
3) ping $ROUTER (wait until ping fails from workstation)
Takes about ~20-30 seconds after step 2 for the local network to
stop working.
Fix this issue by enabling pause slot to only send pause frame once
when FIFO reaches near full state.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125") Reported-by: Grant Grundler <grundler@chromium.org> Tested-by: Grant Grundler <grundler@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: ChunHao Lin <hau@realtek.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/20231129155350.5843-1-hau@realtek.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some potential instances the reference count on struct packet_sock
could be saturated and cause overflows which gets the kernel a bit
confused. To prevent this, move to a 64-bit atomic reference count on
64-bit architectures to prevent the possibility of this type to overflow.
Because we can not handle saturation, using refcount_t is not possible
in this place. Maybe someday in the future if it changes it could be
used. Also, instead of using plain atomic64_t, use atomic_long_t instead.
32-bit machines tend to be memory-limited (i.e. anything that increases
a reference uses so much memory that you can't actually get to 2**32
references). 32-bit architectures also tend to have serious problems
with 64-bit atomics. Hence, atomic_long_t is the more natural solution.
Reported-by: "The UK's National Cyber Security Centre (NCSC)" <security@ncsc.gov.uk> Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@kernel.org Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231201131021.19999-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function trace_buffered_event_disable() is responsible for freeing pages
backing buffered events and this process can run concurrently with
trace_event_buffer_lock_reserve().
The following race is currently possible:
* Function trace_buffered_event_disable() is called on CPU 0. It
increments trace_buffered_event_cnt on each CPU and waits via
synchronize_rcu() for each user of trace_buffered_event to complete.
* After synchronize_rcu() is finished, function
trace_buffered_event_disable() has the exclusive access to
trace_buffered_event. All counters trace_buffered_event_cnt are at 1
and all pointers trace_buffered_event are still valid.
* At this point, on a different CPU 1, the execution reaches
trace_event_buffer_lock_reserve(). The function calls
preempt_disable_notrace() and only now enters an RCU read-side
critical section. The function proceeds and reads a still valid
pointer from trace_buffered_event[CPU1] into the local variable
"entry". However, it doesn't yet read trace_buffered_event_cnt[CPU1]
which happens later.
* Function trace_buffered_event_disable() continues. It frees
trace_buffered_event[CPU1] and decrements
trace_buffered_event_cnt[CPU1] back to 0.
* Function trace_event_buffer_lock_reserve() continues. It reads and
increments trace_buffered_event_cnt[CPU1] from 0 to 1. This makes it
believe that it can use the "entry" that it already obtained but the
pointer is now invalid and any access results in a use-after-free.
Fix the problem by making a second synchronize_rcu() call after all
trace_buffered_event values are set to NULL. This waits on all potential
users in trace_event_buffer_lock_reserve() that still read a previous
pointer from trace_buffered_event.
For instance, it can be triggered by running these two commands in
parallel:
$ while true; do
echo hist:key=id.syscall:val=hitcount > \
/sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/trigger;
done
$ stress-ng --sysinfo $(nproc)
The warning indicates that the current ring_buffer_per_cpu is not in the
committing state. It happens because the active ring_buffer_event
doesn't actually come from the ring_buffer_per_cpu but is allocated from
trace_buffered_event.
The bug is in function trace_buffered_event_disable() where the
following normally happens:
* The code invokes disable_trace_buffered_event() via
smp_call_function_many() and follows it by synchronize_rcu(). This
increments the per-CPU variable trace_buffered_event_cnt on each
target CPU and grants trace_buffered_event_disable() the exclusive
access to the per-CPU variable trace_buffered_event.
* Maintenance is performed on trace_buffered_event, all per-CPU event
buffers get freed.
* The code invokes enable_trace_buffered_event() via
smp_call_function_many(). This decrements trace_buffered_event_cnt and
releases the access to trace_buffered_event.
A problem is that smp_call_function_many() runs a given function on all
target CPUs except on the current one. The following can then occur:
* Task X executing trace_buffered_event_disable() runs on CPU 0.
* The control reaches synchronize_rcu() and the task gets rescheduled on
another CPU 1.
* The RCU synchronization finishes. At this point,
trace_buffered_event_disable() has the exclusive access to all
trace_buffered_event variables except trace_buffered_event[CPU0]
because trace_buffered_event_cnt[CPU0] is never incremented and if the
buffer is currently unused, remains set to 0.
* A different task Y is scheduled on CPU 0 and hits a trace event. The
code in trace_event_buffer_lock_reserve() sees that
trace_buffered_event_cnt[CPU0] is set to 0 and decides the use the
buffer provided by trace_buffered_event[CPU0].
* Task X continues its execution in trace_buffered_event_disable(). The
code incorrectly frees the event buffer pointed by
trace_buffered_event[CPU0] and resets the variable to NULL.
* Task Y writes event data to the now freed buffer and later detects the
created inconsistency.
The issue is observable since commit dea499781a11 ("tracing: Fix warning
in trace_buffered_event_disable()") which moved the call of
trace_buffered_event_disable() in __ftrace_event_enable_disable()
earlier, prior to invoking call->class->reg(.. TRACE_REG_UNREGISTER ..).
The underlying problem in trace_buffered_event_disable() is however
present since the original implementation in commit 0fc1b09ff1ff
("tracing: Use temp buffer when filtering events").
Fix the problem by replacing the two smp_call_function_many() calls with
on_each_cpu_mask() which invokes a given callback on all CPUs.
It use to be that only the top level instance had a snapshot buffer (for
latency tracers like wakeup and irqsoff). When stopping a tracer in an
instance would not disable the snapshot buffer. This could have some
unintended consequences if the irqsoff tracer is enabled.
Consolidate the tracing_start/stop() with tracing_start/stop_tr() so that
all instances behave the same. The tracing_start/stop() functions will
just call their respective tracing_start/stop_tr() with the global_array
passed in.
Link: https://lkml.kernel.org/r/20231205220011.041220035@goodmis.org Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 6d9b3fa5e7f6 ("tracing: Move tracing_max_latency into trace_array") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It use to be that only the top level instance had a snapshot buffer (for
latency tracers like wakeup and irqsoff). The update of the ring buffer
size would check if the instance was the top level and if so, it would
also update the snapshot buffer as it needs to be the same as the main
buffer.
Now that lower level instances also has a snapshot buffer, they too need
to update their snapshot buffer sizes when the main buffer is changed,
otherwise the following can be triggered:
All addresses printed by checkstack have an extra incorrect 0 appended at
the end.
This was introduced with commit 677f1410e058 ("scripts/checkstack.pl: don't
display $dre as different entity"): since then the address is taken from
the line which contains the function name, instead of the line which
contains stack consumption. E.g. on s390:
So the used regex which matches spaces and hexadecimal numbers to extract
an address now matches a different substring. Subsequently replacing spaces
with 0 appends a zero at the and, instead of replacing leading spaces.
Fix this by using the proper regex, and simplify the code a bit.
__thaw_task() was recently updated to warn if the task being thawed was
part of a freezer cgroup that is still currently freezing:
void __thaw_task(struct task_struct *p)
{
...
if (WARN_ON_ONCE(freezing(p)))
goto unlock;
This has exposed a bug in cgroup1 freezing where when CGROUP_FROZEN is
asserted, the CGROUP_FREEZING bits are not also cleared at the same
time. Meaning, when a cgroup is marked FROZEN it continues to be marked
FREEZING as well. This causes the WARNING to trigger, because
cgroup_freezing() thinks the cgroup is still freezing.
There are two ways to fix this:
1. Whenever FROZEN is set, clear FREEZING for the cgroup and all
children cgroups.
2. Update cgroup_freezing() to also verify that FROZEN is not set.
This patch implements option (2), since it's smaller and more
straightforward.
Signed-off-by: Tim Van Patten <timvp@google.com> Tested-by: Mark Hasemeyer <markhas@chromium.org> Fixes: f5d39b020809 ("freezer,sched: Rewrite core freezer logic") Cc: stable@vger.kernel.org # v6.1+ Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If nilfs2 reads a disk image with corrupted segment usage metadata, and
its segment usage information is marked as an error for the segment at the
write location, nilfs_sufile_set_segment_usage() can trigger WARN_ONs
during log writing.
Segments newly allocated for writing with nilfs_sufile_alloc() will not
have this error flag set, but this unexpected situation will occur if the
segment indexed by either nilfs->ns_segnum or nilfs->ns_nextnum (active
segment) was marked in error.
Fix this issue by inserting a sanity check to treat it as a file system
corruption.
Since error returns are not allowed during the execution phase where
nilfs_sufile_set_segment_usage() is used, this inserts the sanity check
into nilfs_sufile_mark_dirty() which pre-reads the buffer containing the
segment usage record to be updated and sets it up in a dirty state for
writing.
In addition, nilfs_sufile_set_segment_usage() is also called when
canceling log writing and undoing segment usage update, so in order to
avoid issuing the same kernel warning in that case, in case of
cancellation, avoid checking the error flag in
nilfs_sufile_set_segment_usage().
When mounting a filesystem image with a block size larger than the page
size, nilfs2 repeatedly outputs long error messages with stack traces to
the kernel log, such as the following:
This overloads the system logger. And to make matters worse, it sometimes
crashes the kernel with a memory access violation.
This is because the return value of the sb_set_blocksize() call, which
should be checked for errors, is not checked.
The latter issue is due to out-of-buffer memory being accessed based on a
large block size that caused sb_set_blocksize() to fail for buffers read
with the initial minimum block size that remained unupdated in the
super_block structure.
Since nilfs2 mkfs tool does not accept block sizes larger than the system
page size, this has been overlooked. However, it is possible to create
this situation by intentionally modifying the tool or by passing a
filesystem image created on a system with a large page size to a system
with a smaller page size and mounting it.
Fix this issue by inserting the expected error handling for the call to
sb_set_blocksize().
Since 64 bit cmpxchg() is very expensive on 32bit architectures, the
timestamp used by the ring buffer does some interesting tricks to be able
to still have an atomic 64 bit number. It originally just used 60 bits and
broke it up into two 32 bit words where the extra 2 bits were used for
synchronization. But this was not enough for all use cases, and all 64
bits were required.
The 32bit version of the ring buffer timestamp was then broken up into 3
32bit words using the same counter trick. But one update was not done. The
check to see if the read operation was done without interruption only
checked the first two words and not last one (like it had before this
update). Fix it by making sure all three updates happen without
interruption by comparing the initial counter with the last updated
counter.
Link: https://lore.kernel.org/linux-trace-kernel/20231206100050.3100b7bb@gandalf.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: f03f2abce4f39 ("ring-buffer: Have 32 bit time stamps use all 64 bits") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Framework Laptop 13 (AMD Ryzen 7040Series) has an ALC295 with
a disconnected or faulty headset mic presence detect similar to the
previous models. It works with the same quirk chain as 309d7363ca3d9fcdb92ff2d958be14d7e8707f68. This model has a VID:PID
of f111:0006.
The pcm state can be SNDRV_PCM_STATE_DISCONNECTED at disconnect
callback, and there is not an entry of SNDRV_PCM_STATE_DISCONNECTED
in snd_pcm_state_names.
This patch adds the missing entry to resolve this issue.
cat /proc/asound/card2/pcm0p/sub0/status
That results in stack traces like the following:
These values mirror those of the Pioneer DJM-250MK2 as the channel layout
appears identical based on my observations. This duplication could be removed in
later contributions if desired.
Signed-off-by: Sarah Grant <s@srd.tw> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20231201181654.5058-1-s@srd.tw Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Callers of mutex_unlock() have to make sure that the mutex stays alive
for the whole duration of the function call. For io_uring that means
that the following pattern is not valid unless we ensure that the
context outlives the mutex_unlock() call.
mutex_lock(&ctx->uring_lock);
req_put(req); // typically via io_req_task_submit()
mutex_unlock(&ctx->uring_lock);
Most contexts are fine: io-wq pins requests, syscalls hold the file,
task works are taking ctx references and so on. However, the task work
fallback path doesn't follow the rule.
Cc: <stable@vger.kernel.org> Fixes: 04fc6c802d ("io_uring: save ctx put/get for task_work submit") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Link: https://lore.kernel.org/io-uring/CAG48ez3xSoYb+45f1RLtktROJrpiDQ1otNvdR+YLQf7m+Krj5Q@mail.gmail.com/ Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
File reference cycles have caused lots of problems for io_uring
in the past, and it still doesn't work exactly right and races with
unix_stream_read_generic(). The safest fix would be to completely
disallow sending io_uring files via sockets via SCM_RIGHT, so there
are no possible cycles invloving registered files and thus rendering
SCM accounting on the io_uring side unnecessary.
This patch adds ASUSTeK COMPUTER INC "E1504FA" to the quirks file acp6x-mach.c
to enable microphone array on ASUS Vivobook GO 15.
I have this laptop and can confirm that the patch succeeds in enabling the
microphone array.
It seems that the pointer-to-kretprobe "rp" within the kretprobe_holder is
RCU-managed, based on the (non-rethook) implementation of get_kretprobe().
The thought behind this patch is to make use of the RCU API where possible
when accessing this pointer so that the needed barriers are always in place
and to self-document the code.
The __rcu annotation to "rp" allows for sparse RCU checking. Plain writes
done to the "rp" pointer are changed to make use of the RCU macro for
assignment. For the single read, the implementation of get_kretprobe()
is simplified by making use of an RCU macro which accomplishes the same,
but note that the log warning text will be more generic.
I did find that there is a difference in assembly generated between the
usage of the RCU macros vs without. For example, on arm64, when using
rcu_assign_pointer(), the corresponding store instruction is a
store-release (STLR) which has an implicit barrier. When normal assignment
is done, a regular store (STR) is found. In the macro case, this seems to
be a result of rcu_assign_pointer() using smp_store_release() when the
value to write is not NULL.
Since the rethook::handler is an RCU-maganged pointer so that it will
notice readers the rethook is stopped (unregistered) or not, it should
be an __rcu pointer and use appropriate functions to be accessed. This
will use appropriate memory barrier when accessing it. OTOH,
rethook::data is never changed, so we don't need to check it in
get_kretprobe().
NOTE: To avoid sparse warning, rethook::handler is defined by a raw
function pointer type with __rcu instead of rethook_handler_t.
It turns out there are more subtle races beyond just the main part of
__iommu_probe_device() itself running in parallel - the dev_iommu_free()
on the way out of an unsuccessful probe can still manage to trip up
concurrent accesses to a device's fwspec. Thus, extend the scope of
iommu_probe_device_lock() to also serialise fwspec creation and initial
retrieval.
If md_set_readonly() failed, the array could still be read-write, however
'MD_RECOVERY_FROZEN' could still be set, which leave the array in an
abnormal state that sync or recovery can't continue anymore.
Hence make sure the flag is cleared after md_set_readonly() returns.
Fixes: 88724bfa68be ("md: wait for pending superblock updates before switching to read-only") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <song@kernel.org> Link: https://lore.kernel.org/r/20231205094215.1824240-3-yukuai1@huaweicloud.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Introduce md_ro_state for mddev->ro, so it is easy to understand.
Signed-off-by: Ye Bin <yebin10@huawei.com> Signed-off-by: Song Liu <song@kernel.org>
Stable-dep-of: c9f7cb5b2bc9 ("md: don't leave 'MD_RECOVERY_FROZEN' in error path of md_set_readonly()") Signed-off-by: Sasha Levin <sashal@kernel.org>
The timer nodes declare compatibility with "fsl,imx6sx-gpt", which
itself is compatible with "fsl,imx6dl-gpt". Switch the fallback
compatible from "fsl,imx6sx-gpt" to "fsl,imx6dl-gpt".
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
Release the id allocated in 'mmdc_pmu_init' when 'devm_kasprintf'
return NULL
When an error occurs in the for loop of beiscsi_init_wrb_handle(), we
should free phwi_ctxt->be_wrbq before returning an error code to prevent
potential memleak.
Fixes: a7909b396ba7 ("[SCSI] be2iscsi: Fix dynamic CID allocation Mechanism in driver") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20231123081941.24854-1-dinghao.liu@zju.edu.cn Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function trace_buffered_event_disable() produces an unexpected warning
when the previous call to trace_buffered_event_enable() fails to
allocate pages for buffered events.
The situation can occur as follows:
* The counter trace_buffered_event_ref is at 0.
* The soft mode gets enabled for some event and
trace_buffered_event_enable() is called. The function increments
trace_buffered_event_ref to 1 and starts allocating event pages.
* The allocation fails for some page and trace_buffered_event_disable()
is called for cleanup.
* Function trace_buffered_event_disable() decrements
trace_buffered_event_ref back to 0, recognizes that it was the last
use of buffered events and frees all allocated pages.
* The control goes back to trace_buffered_event_enable() which returns.
The caller of trace_buffered_event_enable() has no information that
the function actually failed.
* Some time later, the soft mode is disabled for the same event.
Function trace_buffered_event_disable() is called. It warns on
"WARN_ON_ONCE(!trace_buffered_event_ref)" and returns.
Buffered events are just an optimization and can handle failures. Make
trace_buffered_event_enable() exit on the first failure and left any
cleanup later to when trace_buffered_event_disable() is called.
Since commit c7e73b5051d6 ("ARM: imx: mach-imx6ul: remove 14x14 EVK
specific PHY fixup")thet Ethernet PHY is no longer configured via code
in board file.
This caused Ethernet to stop working.
Fix this problem by describing the clocks and clock-names to the
Ethernet PHY node so that the KSZ8081 chip can be clocked correctly.
The i.MX8MP and i.MX8MQ devices both use the same DWC3 controller and
are both affected by a known issue with the controller due to specific
behaviour when park mode is enabled in SuperSpeed host mode operation.
Under heavy USB traffic from multiple endpoints the controller will
sometimes incorrectly process transactions such that some transactions
are lost, or the controller may hang when processing transactions. When
the controller hangs it does not recover.
This issue is documented partially within the linux-imx vendor kernel
which references a Synopsys STAR number 9001415732 in commits [1] and
additional details in [2]. Those commits provide some additional
controller internal implementation specifics around the incorrect
behaviour of the SuperSpeed host controller operation when park mode is
enabled.
The summary of this issue is that the host controller can incorrectly
enter/exit park mode such that part of the controller is in a state
which behaves as if in park mode even though it is not. In this state
the controller incorrectly calculates the number of TRBs available which
results in incorrect access of the internal caches causing the overwrite
of pending requests in the cache which should have been processed but
are ignored. This can cause the controller to drop the requests or hang
waiting for the pending state of the dropped requests.
The workaround for this issue is to disable park mode for SuperSpeed
operation of the controller through the GUCTL1[17] bit. This is already
available as a quirk for the DWC3 controller and can be enabled via the
'snps,parkmode-disable-ss-quirk' device tree property.
It is possible to replicate this failure on an i.MX8MP EVK with a USB
Hub connecting 4 SuperSpeed USB flash drives. Performing continuous
small read operations (dd if=/dev/sd... of=/dev/null bs=16) on the block
devices will result in device errors initially and will eventually
result in the controller hanging.
[13240.896936] xhci-hcd xhci-hcd.0.auto: WARN Event TRB for slot 4 ep 2 with no TDs queued?
[13240.990708] usb 2-1.3: reset SuperSpeed USB device number 5 using xhci-hcd
[13241.015582] sd 2:0:0:0: [sdc] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x07 driverbyte=DRIVER_OK cmd_age=0s
[13241.025198] sd 2:0:0:0: [sdc] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
[13241.032949] I/O error, dev sdc, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 25 prio class 2
[13272.150710] usb 2-1.2: reset SuperSpeed USB device number 4 using xhci-hcd
[13272.175469] sd 1:0:0:0: [sdb] tag#0 UNKNOWN(0x2003) Result: hostbyte=0x03 driverbyte=DRIVER_OK cmd_age=31s
[13272.185365] sd 1:0:0:0: [sdb] tag#0 CDB: opcode=0x28 28 00 00 00 03 e0 00 01 00 00
[13272.193385] I/O error, dev sdb, sector 992 op 0x0:(READ) flags 0x80700 phys_seg 18 prio class 2
[13434.846556] xhci-hcd xhci-hcd.0.auto: xHCI host not responding to stop endpoint command
[13434.854592] xhci-hcd xhci-hcd.0.auto: xHCI host controller not responding, assume dead
[13434.862553] xhci-hcd xhci-hcd.0.auto: HC died; cleaning up
A dependency on this feature was recently introduced:
x86_64-linux-ld: vmlinux.o: in function `tc358768_bridge_pre_enable':
tc358768.c:(.text+0xbe3dae): undefined reference to `drm_display_mode_to_videomode'
When creating ceq_0 during probing irdma, cqp.sc_cqp will be sent as a
cqp_request to cqp->sc_cqp.sq_ring. If the request is pending when
removing the irdma driver or unplugging its aux device, cqp.sc_cqp will be
dereferenced as wrong struct in irdma_free_pending_cqp_request().
64k pages introduce the situation in this diagram when the HCA 4k page
size is being used:
+-------------------------------------------+ <--- 64k aligned VA
| |
| HCA 4k page |
| |
+-------------------------------------------+
| o |
| |
| o |
| |
| o |
+-------------------------------------------+
| |
| HCA 4k page |
| |
+-------------------------------------------+ <--- Live HCA page
|OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO| <--- offset
| | <--- VA
| MR data |
+-------------------------------------------+
| |
| HCA 4k page |
| |
+-------------------------------------------+
| o |
| |
| o |
| |
| o |
+-------------------------------------------+
| |
| HCA 4k page |
| |
+-------------------------------------------+
The VA addresses are coming from rdma-core in this diagram can be
arbitrary, but for 64k pages, the VA may be offset by some number of HCA
4k pages and followed by some number of HCA 4k pages.
The current iterator doesn't account for either the preceding 4k pages or
the following 4k pages.
Fix the issue by extending the ib_block_iter to contain the number of DMA
pages like comment [1] says and by using __sg_advance to start the
iterator at the first live HCA page.
The changes are contained in a parallel set of iterator start and next
functions that are umem aware and specific to umem since there is one user
of the rdma_for_each_block() without umem.
These two fixes prevents the extra pages before and after the user MR
data.
Fix the preceding pages by using the __sq_advance field to start at the
first 4k page containing MR data.
Fix the following pages by saving the number of pgsz blocks in the
iterator state and downcounting on each next.
This fix allows for the elimination of the small page crutch noted in the
Fixes.
Fixes: 10c75ccb54e4 ("RDMA/umem: Prevent small pages from being returned by ib_umem_find_best_pgsz()") Link: https://lore.kernel.org/r/20231129202143.1434-2-shiraz.saleem@intel.com Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When wm_adsp_buffer_read() fails, we should free buf->regions.
Otherwise, the callers of wm_adsp_buffer_populate() will
directly free buf on failure, which makes buf->regions a leaked
memory.
Fixes: a792af69b08f ("ASoC: wm_adsp: Refactor compress stream initialisation") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20231204074158.12026-1-dinghao.liu@zju.edu.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The -1 value for active_decimator[dai_id] is considered as "not set",
but at probe the table is initialized a 0, this prevents enabling the
DEC0 Mixer since it will be considered as already set.
Initialize the table entries as -1 to fix tx_macro_tx_mixer_put().
"If an error occurs while obtaining the meter reading or if the value
is not available then an Integer with all bits set is returned"
Since the "integer" is 32 bits in case of the ACPI power meter,
userspace will get a power reading of 2^32 * 1000 miliwatts (~4.29 MW)
in case of such an error. This was discovered due to a lm_sensors
bugreport (https://github.com/lm-sensors/lm-sensors/issues/460).
Fix this by returning -ENODATA instead.
Tested-by: <urbinek@gmail.com> Fixes: de584afa5e18 ("hwmon driver for ACPI 4.0 power meters") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20231124182747.13956-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When removing the irdma driver or unplugging its aux device, the ccq
queue is released before destorying the cqp_cmpl_wq queue.
But in the window, there may still be completion events for wqes. That
will cause a UAF in irdma_sc_ccq_get_cqe_info().
As we chain the WR during write request: memory registration,
rdma write, local invalidate, if only the last WR fail to send due
to send queue overrun, the server can send back the reply, while
client mark the req->in_use to false in case of error in rtrs_clt_req
when error out from rtrs_post_rdma_write_sg.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-8-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For each write request, we need Request, Response Memory Registration,
Local Invalidate.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-7-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
