The tasklet software interrupt takes too much time. Therefore, the
xfrm_trans_reinject executor is changed from tasklet to workqueue. Add add
spin lock to protect the queue. This reduces the processing flow of the
tcp_sendmsg function in this scenario.
Fixes: acf568ee859f0 ("xfrm: Reinject transport-mode packets through tasklet") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change that introduced the use of __check_timeout did not account for
link types properly, it always assumes ACL_LINK is used thus causing
hdev->acl_last_tx to be used even in case of LE_LINK and then again
uses ACL_LINK with hci_link_tx_to.
To fix this __check_timeout now takes the link type as parameter and
then procedure to use the right last_tx based on the link type and pass
it to hci_link_tx_to.
Fixes: 1b1d29e51499 ("Bluetooth: Make use of __check_timeout on hci_sched_le") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Tested-by: David Beinder <david@beinder.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Linux is not the only entity using the BlueField I2C busses so
support a lock mechanism provided by hardware to avoid issues
when multiple entities are trying to access the same bus.
The lock is acquired whenever written explicitely or the lock
register is read. So make sure it is always released at the end
of a successful or failed transaction.
The list iterator value will *always* be set and non-NULL by
list_for_each_entry(), so it is incorrect to assume that the iterator
value will be NULL if the list is empty or no element is found in list.
Use a new value 'iter' as the list iterator, while use the old value
'item' as a dedicated pointer to point to the found element, which
1. can fix this bug, due to now 'item' is NULL only if it's not found.
2. do not need to change all the uses of 'item' after the loop.
3. can also limit the scope of the list iterator 'iter' *only inside*
the traversal loop by simply declaring 'iter' inside the loop in the
future, as usage of the iterator outside of the list_for_each_entry
is considered harmful. https://lkml.org/lkml/2022/2/17/1032
Fixes: a910e4a94f692 ("cw1200: add driver for the ST-E CW1100 & CW1200 WLAN chipsets") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220413091723.17596-1-xiam0nd.tong@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In sk_psock_backlog function, for ingress direction skb, if no new data
packet arrives after the skb is cached, the cached skb does not have a
chance to be added to the receive queue of psock. As a result, the cached
skb cannot be received by the upper-layer application. Fix this by reschedule
the psock work to dispose the cached skb in sk_msg_recvmsg function.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Liu Jian <liujian56@huawei.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20220907071311.60534-1-liujian56@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:db91841b58f9a ("spi/omap100k: Convert to runtime PM")
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
The pm_runtime_enable will increase power disable depth. Thus
a pairing decrement is needed on the error handling path to
keep it balanced according to context.
Fixes:73d5fe0462702 ("spi: cadence-quadspi: Remove spi_master_put() in probe failure path")
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561227] ath11k c000000.wifi: peer already added vdev id 0 req, vdev id 1 present
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561282] ath11k c000000.wifi: Failed to add peer: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.568053] ath11k c000000.wifi: Failed to add station: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: Could not add STA to kernel driver
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: did not acknowledge authentication response
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED 28:c2:1f:xx:xx:xx
Wed Jun 1 22:19:31 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: disassociated due to inactivity
Wed Jun 1 22:19:32 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
To repro this:
- Have 2 Wifi with the same bssid and pass on different band (2.4 and
5GHz)
- Enable 802.11r Fast Transaction with same mobility domain
- FT Protocol: FT over the Air
From a openwrt system issue the command (with the correct mac)
ubus call hostapd.wlan1 wnm_disassoc_imminent '{"addr":"28:C2:1F:xx:xx:xx"}'
Notice the log printing the errors.
The cause of this error has been investigated and we found that this is
related to the WiFi Fast Transaction feature. We observed that this is
triggered when the router tells the device to change band. In this case
the device first auth to the other band and then the disconnect path
from the prev band is triggered.
This is problematic with the current rhash implementation since the
addrs is used as key and the logic of "adding first, delete later"
conflicts with the rhash logic.
In fact peer addition will fail since the peer is already added and with
that fixed a peer deletion will cause unitended effect by removing the
peer just added.
Current solution to this is to add additional logic to the peer delete,
make sure we are deleting the correct peer taken from the rhash
table (and fallback to the peer list) and for the peer add logic delete
the peer entry for the rhash list before adding the new one (counting as
an error only when a peer with the same vlan_id is asked to be added).
With this change, a sta can correctly transition from 2.4GHz and 5GHZ
with no drop and no error are printed.
In preparation for reducing the use of ksize(), record the actual
allocation size for later memcpy(). This avoids copying extra
(uninitialized!) bytes into the patch buffer when the requested
allocation size isn't exactly the size of a kmalloc bucket.
Additionally, fix potential future issues where runtime bounds checking
will notice that the buffer was allocated to a smaller value than
returned by ksize().
Fixes: 757885e94a22 ("x86, microcode, amd: Early microcode patch loading support for AMD") Suggested-by: Daniel Micay <danielmicay@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lore.kernel.org/lkml/CA+DvKQ+bp7Y7gmaVhacjv9uF6Ar-o4tet872h4Q8RPYPJjcJQA@mail.gmail.com/ Signed-off-by: Sasha Levin <sashal@kernel.org>
The number of spatial streams used when acting as a beamformee in VHT
mode are reported by the firmware as 7 (8 sts - 1) both in IPQ6018 and
IPQ8074 which respectively have 2 and 4 sts each. So the firmware should
report 1 (2 - 1) and 3 (4 - 1).
Fix this by checking that the number of VHT beamformee sts reported by
the firmware is not greater than the number of receiving antennas - 1.
The fix is based on the same approach used in this same function for
sanitizing the number of sounding dimensions reported by the firmware.
Without this change, acting as a beamformee in VHT mode is not working
properly.
It has a fail log which is ath11k_dbg in ath11k_dp_rx_process_mon_status(),
as below, it will not print when debug_mask is not set ATH11K_DBG_DATA.
ath11k_dbg(ab, ATH11K_DBG_DATA,
"failed to find the peer with peer_id %d\n",
ppdu_info.peer_id);
When run scan with station disconnected, the peer_id is 0 for case
HAL_RX_MPDU_START in ath11k_hal_rx_parse_mon_status_tlv() which called
from ath11k_dp_rx_process_mon_status(), and the peer_id of ppdu_info is
reset to 0 in the while loop, so it does not match condition of the
check "if (ppdu_info->peer_id == HAL_INVALID_PEERID" in the loop, and
then the log "failed to find the peer with peer_id 0" print after the
check in the loop, it is below call stack when debug_mask is set
ATH11K_DBG_DATA.
The reason is this commit 01d2f285e3e5 ("ath11k: decode HE status tlv")
add "memset(ppdu_info, 0, sizeof(struct hal_rx_mon_ppdu_info))" in
ath11k_dp_rx_process_mon_status(), but the commit does not initialize
the peer_id to HAL_INVALID_PEERID, then lead the check mis-match.
Reset the default value to HAL_INVALID_PEERID each time after memset
of ppdu_info as well as others memset which existed in function
ath11k_dp_rx_process_mon_status(), then the failed log disappeared.
We've met the problem that when there is a vlan tag inside
GRE encapsulation, the match of num_of_vlans fails.
It is caused by the vlan tag inside GRE payload has been
counted into num_of_vlans, which is not expected.
One example packet is like this:
Ethernet II, Src: Broadcom_68:56:07 (00:10:18:68:56:07)
Dst: Broadcom_68:56:08 (00:10:18:68:56:08)
802.1Q Virtual LAN, PRI: 0, DEI: 0, ID: 100
Internet Protocol Version 4, Src: 192.168.1.4, Dst: 192.168.1.200
Generic Routing Encapsulation (Transparent Ethernet bridging)
Ethernet II, Src: Broadcom_68:58:07 (00:10:18:68:58:07)
Dst: Broadcom_68:58:08 (00:10:18:68:58:08)
802.1Q Virtual LAN, PRI: 0, DEI: 0, ID: 200
...
It should match the (num_of_vlans 1) rule, but it matches
the (num_of_vlans 2) rule.
The vlan tags inside the GRE or other tunnel encapsulated payload
should not be taken into num_of_vlans.
The fix is to stop counting the vlan number when the encapsulation
bit is set.
Fixes: 34951fcf26c5 ("flow_dissector: Add number of vlan tags dissector") Signed-off-by: Qingqing Yang <qingqing.yang@broadcom.com> Reviewed-by: Boris Sukholitko <boris.sukholitko@broadcom.com> Link: https://lore.kernel.org/r/20220919074808.136640-1-qingqing.yang@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The previous commit changed the way the rescheduling delay is computed
which has a side effect: the bias is now represented as much as the
other entries in the rescheduling delay which makes the logic to kick in
only with very large sets, as the initial interval is very large
(INT_MAX).
Revisit the GC initial bias to allow more frequent GC for smaller sets
while still avoiding wakeups when a machine is mostly idle. We're moving
from a large initial value to pretending we have 100 entries expiring at
the upper bound. This way only a few entries having a small timeout
won't impact much the rescheduling delay and non-idle machines will have
enough entries to lower the delay when needed. This also improves
readability as the initial bias is now linked to what is computed
instead of being an arbitrary large value.
Commit 2cfadb761d3d ("netfilter: conntrack: revisit gc autotuning")
changed the eviction rescheduling to the use average expiry of scanned
entries (within 1-60s) by doing:
The issue is the above will make the average ('next_run' here) more
dependent on the last expiration values than the firsts (for sets > 2).
Depending on the expiration values used to compute the average, the
result can be quite different than what's expected. To fix this we can
do the following:
syzbot is reporting NULL pointer dereference at hci_uart_tty_close() [1],
for rcu_sync_enter() is called without rcu_sync_init() due to
hci_uart_tty_open() ignoring percpu_init_rwsem() failure.
While we are at it, fix that hci_uart_register_device() ignores
percpu_init_rwsem() failure and hci_uart_unregister_device() does not
call percpu_free_rwsem().
Link: https://syzkaller.appspot.com/bug?extid=576dfca25381fb6fbc5f Reported-by: syzbot <syzbot+576dfca25381fb6fbc5f@syzkaller.appspotmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Fixes: 67d2f8781b9f00d1 ("Bluetooth: hci_ldisc: Allow sleeping while proto locks are held.") Fixes: d73e172816652772 ("Bluetooth: hci_serdev: Init hci_uart proto_lock to avoid oops") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In current code STA_KEEPALIVE_ARP_RESPONSE TLV header is included only
when ARP method is used, this causes firmware always to crash when wowlan
is enabled because firmware needs it to be present no matter ARP method
is used or not.
Fix this issue by including STA_KEEPALIVE_ARP_RESPONSE TLV header by
default.
Also fix below typo:
s/WMI_TAG_STA_KEEPALVE_ARP_RESPONSE/WMI_TAG_STA_KEEPALIVE_ARP_RESPONSE/
Should check of_iomap return value 'fep->fec.fecp' instead of 'fep->fcc.fccp'
Fixes: 976de6a8c304 ("fs_enet: Be an of_platform device when CONFIG_PPC_CPM_NEW_BINDING is set.") Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
To fix this when the call __rfcomm_sock_close is now done without
holding the lock_sock since rfcomm_dlc_lock exists to protect
the dlc data there is no need to use lock_sock in that code path.
In insmod/rmmod stress test, the following crash dump shows up immediately.
The problem is caused by missing mt76_dev in mt7921_pci_remove(). We
should make sure the drvdata is ready before probe() finished.
Do not need to check running state before configuring implicit Tx
beamform. It is okay to configure implicit Tx beamform in run time.
Noted that the existing connected stations will be applied for new
configuration only if they reconnected to the interface.
Fix the error that mcs will be reduced to a range of 0 to 7 in ht mode.
Fixes: 70fd1333cd32 ("mt76: mt7915: rework .set_bitrate_mask() to support more options") Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add mt7921_mutex_acquire at mt7921_[start, stop]_ap to fix the race
with the context holding dev->muxtex and the driver might access the
device in low power state.
Fixes: 24299fc869f7 ("mt76: mt7921: enable rx header traslation offload") Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add mt7921_mutex_acquire at mt7921_[start, stop]_ap to fix the race
with the context holding dev->muxtex and the driver might access the
device in low power state.
Fixes: 9d958b60ebc2 ("mt76: mt7921: fix command timeout in AP stop period") Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Acked-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to mt7921 driver, introduce mt7615_mutex_acquire/release in
mt7615_sta_set_decap_offload in order to avoid sending mcu commands
while the device is in low-power state.
Fixes: d4b98c63d7a77 ("mt76: mt7615: add support for rx decapsulation offload") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix transmitting packets hangs with continuing to pull the pending packet
from mac80211 queues when receiving Tx status notification from the device.
Fixes: aac5104bf631 ("mt76: sdio: do not run mt76_txq_schedule directly") Acked-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: YN Chen <yn.chen@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not meaningful to poll sta stat when there is no data traffic.
So polling sta stat when the device has transmitted data instead to save
CPU power.
That implies that it is unallowed the stat_work to work while MCU is being
initialized in the really early stage to fix the possible time to time MCU
initialization failure.
Fixes: d39b52e31aa6 ("mt76: introduce mt76_sdio module") Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because wake_work and sdio->stat_work share the same workqueue mt76->wq,
if sdio->stat_work cannot acquire the mutex lock such as that was possibly
held up by [mt7615, mt7921]_mutex_acquire. Additionally, if
[mt7615, mt7921]_mutex_acquire was called by sdio->stat_work self, the wake
would be blocked by itself. Thus, we move the stat_work into
ieee80211_workqueue instead to break the deadlock.
Fixes: d39b52e31aa6 ("mt76: introduce mt76_sdio module") Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is unexpected that the reset work is running simultaneously with
the suspend or resume context and it is possible that reset work is still
running even after mt7921 is suspended if we don't fix the race issue.
Thus, the suspend procedure should be waiting until the reset is completed
at the beginning and ignore the subsequent the reset requests.
In case there is an error that happens during either suspend or resume
handler, we will schedule a reset task to recover the error before
returning the error code to ensure we can immediately fix the error there.
Fixes: df3e4143ba8a ("mt76: mt7921u: add suspend/resume support") Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is unexpected that the reset work is running simultaneously with
the suspend or resume context and it is possible that reset work is still
running even after mt7921 is suspended if we don't fix the race issue.
Thus, the suspend procedure should be waiting until the reset is completed
at the beginning and ignore the subsequent the reset requests.
In case there is an error that happens during either suspend or resume
handler, we will schedule a reset task to recover the error before
returning the error code to ensure we can immediately fix the error there.
Fixes: ca74b9b907f9 ("mt76: mt7921s: add reset support") Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is unexpected that the reset work is running simultaneously with
the suspend or resume context and it is possible that reset work is still
running even after mt7921 is suspended if we don't fix the race issue.
Thus, the suspend procedure should be waiting until the reset is completed
at the beginning and ignore the subsequent the reset requests.
In case there is an error that happens during either suspend or resume
handler, we will schedule a reset task to recover the error before
returning the error code to ensure we can immediately fix the error there.
Fixes: 0c1ce9884607 ("mt76: mt7921: add wifi reset support") Co-developed-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: YN Chen <YN.Chen@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sasha Levin <sashal@kernel.org>
Found by comparing with the vendor driver. Currently this affects
only the RTL8192EU, which is the only gen2 chip with 2 TX paths
supported by this driver. It's unclear what kind of effect the
mistake had in practice, since I don't have any RTL8192EU devices
to test it.
Fixes: e1547c535ede ("rtl8xxxu: First stab at adding IQK calibration for 8723bu parts") Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/30a59f3a-cfa9-8379-7af0-78a8f4c77cfd@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When trying to finish resolving a struct member, btf_struct_resolve
saves the member type id in a u16 temporary variable. This truncates
the 32 bit type id value if it exceeds UINT16_MAX.
As a result, structs that have members with type ids > UINT16_MAX and
which need resolution will fail with a message like this:
Since [1], controller's busy flag isn't set anymore when the
__spi_transfer_message_noqueue() is used instead of the
__spi_pump_transfer_message() logic for spi_sync transfers.
Since the pow2 clock ops were limited to only be available when a
transfer is ongoing (between prepare_transfer_hardware and
unprepare_transfer_hardware callbacks), the only way to track this
down is to check for the controller cur_msg.
[1] ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync")
Fixes: 09992025dacd ("spi: meson-spicc: add local pow2 clock ops to preserve rate between messages") Fixes: ae7d2346dc89 ("spi: Don't use the message queue if possible in spi_sync") Reported-by: Markus Schneider-Pargmann <msp@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Markus Schneider-Pargmann <msp@baylibre.com> Link: https://lore.kernel.org/r/20220908121803.919943-1-narmstrong@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
rtl8xxxu_queue_select() selects the wrong TX queues because it's
reading memory from the wrong address. It expects to find ieee80211_hdr
at skb->data, but that's not the case after skb_push(). Move the call
to rtl8xxxu_queue_select() before the call to skb_push().
The put lowers the reference count to 0 and frees ctx, reading it
afterwards is invalid. Move the put after the uses and determine the
last use by the reference count being 1.
Fixes: 39e940d4abfa ("selftests/xsk: Destroy BPF resources only when ctx refcount drops to 0") Signed-off-by: Ian Rogers <irogers@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/bpf/20220901202645.1463552-1-irogers@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
There some bounds checking to ensure that "map_addr" is not out of
bounds before the start of the loop. But the checking needs to be
done as we iterate through the loop because "map_addr" gets larger as
we iterate.
Fixes: 26f1fad29ad9 ("New driver: rtl8xxxu (mac80211)") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/Yv8eGLdBslLAk3Ct@kili Signed-off-by: Sasha Levin <sashal@kernel.org>
Number of TX resource must be minimum of TX_BD and TX_WD. Only considering
TX_BD could drop TX packets pulled from mac80211 if TX_WD is unavailable.
Fixes: 52edbb9fb78a ("rtw89: ps: access TX/RX rings via another registers in low power mode") Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220824063312.15784-2-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
We turn off interrupt in ISR, and re-enable interrupt in threadfn or
napi_poll according to the mode it stays. If we are turning off interrupt,
rtwpci->running flag is unset and interrupt handler stop processing even
if it was called, so disallow to re-enable interrupt in this situation.
Or, wifi chip doesn't trigger interrupt events anymore because interrupt
status (ISR) isn't clear by interrupt handler anymore.
Fixes: c83dcd0508e2 ("rtw89: pci: add a separate interrupt handler for low power mode") Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220824063312.15784-1-pkshih@realtek.com Signed-off-by: Sasha Levin <sashal@kernel.org>
WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.
Fixes: a1c49c434e15 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices") Co-developed-by: Jing Cai <jing.cai@mediatek.com> Signed-off-by: Jing Cai <jing.cai@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both __this_cpu_inc_return() and __this_cpu_dec() are not preemption
safe and now migrate_disable() doesn't disable preemption, so the update
of prog-active is not atomic and in theory under fully preemptible kernel
recurisve prevention may do not work.
Fixing by using the preemption-safe and IRQ-safe variants.
Fixes: ca06f55b9002 ("bpf: Add per-program recursion prevention mechanism") Signed-off-by: Hou Tao <houtao1@huawei.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/r/20220901061938.3789460-3-houtao@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Now migrate_disable() does not disable preemption and under some
architectures (e.g. arm64) __this_cpu_{inc|dec|inc_return} are neither
preemption-safe nor IRQ-safe, so for fully preemptible kernel concurrent
lookups or updates on the same task local storage and on the same CPU
may make bpf_task_storage_busy be imbalanced, and
bpf_task_storage_trylock() on the specific cpu will always fail.
Fixing it by using this_cpu_{inc|dec|inc_return} when manipulating
bpf_task_storage_busy.
Fixes: bc235cdb423a ("bpf: Prevent deadlock from recursive bpf_task_storage_[get|delete]") Signed-off-by: Hou Tao <houtao1@huawei.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Link: https://lore.kernel.org/r/20220901061938.3789460-2-houtao@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
QMI message IDs for some of the QMI messages were incorrectly
defined in the original implementation. These have to be corrected
to enable cold boot support on WCN6750. These corrections are
applicable for all chipsets and will not impact them. Refactor the
code accordingly.
In __htab_map_lookup_and_delete_batch() if htab_lock_bucket() returns
-EBUSY, it will go to next bucket. Going to next bucket may not only
skip the elements in current bucket silently, but also incur
out-of-bound memory access or expose kernel memory to userspace if
current bucket_cnt is greater than bucket_size or zero.
Fixing it by stopping batch operation and returning -EBUSY when
htab_lock_bucket() fails, and the application can retry or skip the busy
batch as needed.
Fixes: 20b6cc34ea74 ("bpf: Avoid hashtab deadlock with map_locked") Reported-by: Hao Sun <sunhao.th@gmail.com> Signed-off-by: Hou Tao <houtao1@huawei.com> Link: https://lore.kernel.org/r/20220831042629.130006-3-houtao@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Per-cpu htab->map_locked is used to prohibit the concurrent accesses
from both NMI and non-NMI contexts. But since commit 74d862b682f5
("sched: Make migrate_disable/enable() independent of RT"),
migrate_disable() is also preemptible under CONFIG_PREEMPT case, so now
map_locked also disallows concurrent updates from normal contexts
(e.g. userspace processes) unexpectedly as shown below:
process A process B
htab_map_update_elem()
htab_lock_bucket()
migrate_disable()
/* return 1 */
__this_cpu_inc_return()
/* preempted by B */
htab_map_update_elem()
/* the same bucket as A */
htab_lock_bucket()
migrate_disable()
/* return 2, so lock fails */
__this_cpu_inc_return()
return -EBUSY
A fix that seems feasible is using in_nmi() in htab_lock_bucket() and
only checking the value of map_locked for nmi context. But it will
re-introduce dead-lock on bucket lock if htab_lock_bucket() is re-entered
through non-tracing program (e.g. fentry program).
One cannot use preempt_disable() to fix this issue as htab_use_raw_lock
being false causes the bucket lock to be a spin lock which can sleep and
does not work with preempt_disable().
Therefore, use migrate_disable() when using the spinlock instead of
preempt_disable() and defer fixing concurrent updates to when the kernel
has its own BPF memory allocator.
Fixes: 74d862b682f5 ("sched: Make migrate_disable/enable() independent of RT") Reviewed-by: Hao Luo <haoluo@google.com> Signed-off-by: Hou Tao <houtao1@huawei.com> Link: https://lore.kernel.org/r/20220831042629.130006-2-houtao@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit d678cbd2f867 ("xsk: Fix handling of invalid descriptors in XSK TX
batching API") fixed batch API usage against set of descriptors with
invalid ones but introduced a problem when AF_XDP SW rings are smaller
than HW ones. Mismatch of reported Tx'ed frames between HW generator and
user space app was observed. It turned out that backpressure mechanism
became a bottleneck when the amount of produced descriptors to CQ is
lower than what we grabbed from XSK Tx ring.
Say that 512 entries had been taken from XSK Tx ring but we had only 490
free entries in CQ. Then callsite (ZC driver) will produce only 490
entries onto HW Tx ring but 512 entries will be released from Tx ring
and this is what will be seen by the user space.
In order to fix this case, mix XSK Tx/CQ ring interractions by moving
around internal functions and changing call order:
* pull out xskq_prod_nb_free() from xskq_prod_reserve_addr_batch()
up to xsk_tx_peek_release_desc_batch();
** move xskq_cons_release_n() into xskq_cons_read_desc_batch()
After doing so, algorithm can be described as follows:
1. lookup Tx entries
2. use value from 1. to reserve space in CQ (*)
3. Read from Tx ring as much descriptors as value from 2
3a. release descriptors from XSK Tx ring (**)
4. Finally produce addresses to CQ
Fixes: d678cbd2f867 ("xsk: Fix handling of invalid descriptors in XSK TX batching API") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220830121705.8618-1-maciej.fijalkowski@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The current pseudo_lock.c code overwrites the value of the
MSR_MISC_FEATURE_CONTROL to 0 even if the original value is not 0.
Therefore, modify it to save and restore the original values.
'status' is known to be 0 at this point. The expected error code is
PTR_ERR(clk).
Switch to dev_err_probe() in order to display the expected error code (in a
human readable way).
This also filters -EPROBE_DEFER cases, should it happen.
Commit 23c7f8d7989e ("net: Fix esp GSO on inter address family
tunnels.") is incomplete. It passes to skb_eth_gso_segment the
protocol for the outer IP version, instead of the inner IP version, so
we end up calling inet_gso_segment on an inner IPv6 packet and
ipv6_gso_segment on an inner IPv4 packet and the packets are dropped.
This patch completes the fix by selecting the correct protocol based
on the inner mode's family.
Since audit_proctitle is generated at syscall exit time, its value is
used immediately and cached for the next syscall. Since this is the
case, then only clear it at task exit time. Otherwise, there is no
point in caching the value OR bearing the overhead of regenerating it.
Fixes: 12c5e81d3fd0 ("audit: prepare audit_context for use in calling contexts beyond syscalls") Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Be explicit in checking the struct audit_context "context" member enum
value rather than assuming the order of context enum values.
Fixes: 12c5e81d3fd0 ("audit: prepare audit_context for use in calling contexts beyond syscalls") Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When `data` points to a boolean value, casting it to `int *` is problematic
and could lead to a wrong value being passed to `jsonw_bool`. Change the
cast to `bool *` instead.
From 'IEEE Std 802.11-2020 section 11.8.8.4.1':
The mesh channel switch may be triggered by the need to avoid
interference to a detected radar signal, or to reassign mesh STA
channels to ensure the MBSS connectivity.
A 20/40 MHz MBSS may be changed to a 20 MHz MBSS and a 20 MHz
MBSS may be changed to a 20/40 MHz MBSS.
Since the standard allows the change of bandwidth during
the channel switch in mesh, remove the bandwidth check present in
ieee80211_set_csa_beacon.
Fixes: c6da674aff94 ("{nl,cfg,mac}80211: enable the triggering of CSA frame in mesh") Signed-off-by: Hari Chandrakanthan <quic_haric@quicinc.com> Link: https://lore.kernel.org/r/1658903549-21218-1-git-send-email-quic_haric@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When checking for channel regulatory validity, use the
AP link chandef (and not mesh's chandef).
Fixes: 7b0a0e3c3a88 ("wifi: cfg80211: do some rework towards MLO link APIs") Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, verifier verifies callback functions (sync and async) as if
they will be executed once, (i.e. it explores execution state as if the
function was being called once). The next insn to explore is set to
start of subprog and the exit from nested frame is handled using
curframe > 0 and prepare_func_exit. In case of async callback it uses a
customized variant of push_stack simulating a kind of branch to set up
custom state and execution context for the async callback.
While this approach is simple and works when callback really will be
executed only once, it is unsafe for all of our current helpers which
are for_each style, i.e. they execute the callback multiple times.
A callback releasing acquired references of the caller may do so
multiple times, but currently verifier sees it as one call inside the
frame, which then returns to caller. Hence, it thinks it released some
reference that the cb e.g. got access through callback_ctx (register
filled inside cb from spilled typed register on stack).
Similarly, it may see that an acquire call is unpaired inside the
callback, so the caller will copy the reference state of callback and
then will have to release the register with new ref_obj_ids. But again,
the callback may execute multiple times, but the verifier will only
account for acquired references for a single symbolic execution of the
callback, which will cause leaks.
Note that for async callback case, things are different. While currently
we have bpf_timer_set_callback which only executes it once, even for
multiple executions it would be safe, as reference state is NULL and
check_reference_leak would force program to release state before
BPF_EXIT. The state is also unaffected by analysis for the caller frame.
Hence async callback is safe.
Since we want the reference state to be accessible, e.g. for pointers
loaded from stack through callback_ctx's PTR_TO_STACK, we still have to
copy caller's reference_state to callback's bpf_func_state, but we
enforce that whatever references it adds to that reference_state has
been released before it hits BPF_EXIT. This requires introducing a new
callback_ref member in the reference state to distinguish between caller
vs callee references. Hence, check_reference_leak now errors out if it
sees we are in callback_fn and we have not released callback_ref refs.
Since there can be multiple nested callbacks, like frame 0 -> cb1 -> cb2
etc. we need to also distinguish between whether this particular ref
belongs to this callback frame or parent, and only error for our own, so
we store state->frameno (which is always non-zero for callbacks).
In short, callbacks can read parent reference_state, but cannot mutate
it, to be able to use pointers acquired by the caller. They must only
undo their changes (by releasing their own acquired_refs before
BPF_EXIT) on top of caller reference_state before returning (at which
point the caller and callback state will match anyway, so no need to
copy it back to caller).
Fixed register define is not used, but register definition shall be kept
in sync.
Fixes: 403f69bbdbad ("tsnep: Add TSN endpoint Ethernet MAC driver") Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex might still be in use until the devm cleanup callback
devm_led_classdev_flash_release() is called. This only happens some time
after lm3601x_remove() completed.
Fixes: e63a744871a3 ("leds: lm3601x: Convert class registration to device managed") Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Discussion around a recently-submitted patch provided historical
context for check_refcount_ok [0]. Specifically, the function and its
helpers - may_be_acquire_function and arg_type_may_be_refcounted -
predate the OBJ_RELEASE type flag and the addition of many more helpers
with acquire/release semantics.
The purpose of check_refcount_ok is to ensure:
1) Helper doesn't have multiple uses of return reg's ref_obj_id
2) Helper with release semantics only has one arg needing to be
released, since that's tracked using meta->ref_obj_id
With current verifier, it's safe to remove check_refcount_ok and its
helpers. Since addition of OBJ_RELEASE type flag, case 2) has been
handled by the arg_type_is_release check in check_func_arg. To ensure
case 1) won't result in verifier silently prioritizing one use of
ref_obj_id, this patch adds a helper_multiple_ref_obj_use check which
fails loudly if a helper passes > 1 test for use of ref_obj_id.
/* size: 504, cachelines: 8, members: 7 */
/* sum members: 503, holes: 1, sum holes: 1 */
/* last cacheline: 56 bytes */
};
Suggested-by: Jakub Sitnicki <jakub@cloudflare.com> Reviewed-by: Jakub Sitnicki <jakub@cloudflare.com> Reviewed-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Stanislav Fomichev <sdf@google.com> Link: https://lore.kernel.org/r/20220628174314.1216643-3-sdf@google.com Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: 883743422ced ("bpf: Fix ref_obj_id for dynptr data slices in verifier") Signed-off-by: Sasha Levin <sashal@kernel.org>
When peer delete failed in a disconnect operation, use-after-free
detected by KFENCE in below log. It is because for each vdev_id and
address, it has only one struct ath10k_peer, it is allocated in
ath10k_peer_map_event(). When connected to an AP, it has more than
one HTT_T2H_MSG_TYPE_PEER_MAP reported from firmware, then the
array peer_map of struct ath10k will be set muti-elements to the
same ath10k_peer in ath10k_peer_map_event(). When peer delete failed
in ath10k_sta_state(), the ath10k_peer will be free for the 1st peer
id in array peer_map of struct ath10k, and then use-after-free happened
for the 2nd peer id because they map to the same ath10k_peer.
And clean up all peers in array peer_map for the ath10k_peer, then
user-after-free disappeared
peer map event log:
[ 306.911021] wlan0: authenticate with b0:2a:43:e6:75:0e
[ 306.957187] ath10k_pci 0000:01:00.0: mac vdev 0 peer create b0:2a:43:e6:75:0e (new sta) sta 1 / 32 peer 1 / 33
[ 306.957395] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 306.957404] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 306.986924] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 166
peer unmap event log:
[ 435.715691] wlan0: deauthenticating from b0:2a:43:e6:75:0e by local choice (Reason: 3=DEAUTH_LEAVING)
[ 435.716802] ath10k_pci 0000:01:00.0: mac vdev 0 peer delete b0:2a:43:e6:75:0e sta ffff990e0e9c2b50 (sta gone)
[ 435.717177] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 435.717186] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 435.717193] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 166
use-after-free log:
[21705.888627] wlan0: deauthenticating from d0:76:8f:82:be:75 by local choice (Reason: 3=DEAUTH_LEAVING)
[21713.799910] ath10k_pci 0000:01:00.0: failed to delete peer d0:76:8f:82:be:75 for vdev 0: -110
[21713.799925] ath10k_pci 0000:01:00.0: found sta peer d0:76:8f:82:be:75 (ptr 0000000000000000 id 102) entry on vdev 0 after it was supposedly removed
[21713.799968] ==================================================================
[21713.799991] BUG: KFENCE: use-after-free read in ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.799991]
[21713.799997] Use-after-free read at 0x00000000abe1c75e (in kfence-#69):
[21713.800010] ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.800041] drv_sta_state+0x115/0x677 [mac80211]
[21713.800059] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800076] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800093] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800110] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800137] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800153] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800161] genl_rcv_msg+0x38e/0x3be
[21713.800166] netlink_rcv_skb+0x89/0xf7
[21713.800171] genl_rcv+0x28/0x36
[21713.800176] netlink_unicast+0x179/0x24b
[21713.800181] netlink_sendmsg+0x3a0/0x40e
[21713.800187] sock_sendmsg+0x72/0x76
[21713.800192] ____sys_sendmsg+0x16d/0x1e3
[21713.800196] ___sys_sendmsg+0x95/0xd1
[21713.800200] __sys_sendmsg+0x85/0xbf
[21713.800205] do_syscall_64+0x43/0x55
[21713.800210] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[21713.800213]
[21713.800219] kfence-#69: 0x000000009149b0d5-0x000000004c0697fb, size=1064, cache=kmalloc-2k
[21713.800219]
[21713.800224] allocated by task 13 on cpu 0 at 21705.501373s:
[21713.800241] ath10k_peer_map_event+0x7e/0x154 [ath10k_core]
[21713.800254] ath10k_htt_t2h_msg_handler+0x586/0x1039 [ath10k_core]
[21713.800265] ath10k_htt_htc_t2h_msg_handler+0x12/0x28 [ath10k_core]
[21713.800277] ath10k_htc_rx_completion_handler+0x14c/0x1b5 [ath10k_core]
[21713.800283] ath10k_pci_process_rx_cb+0x195/0x1df [ath10k_pci]
[21713.800294] ath10k_ce_per_engine_service+0x55/0x74 [ath10k_core]
[21713.800305] ath10k_ce_per_engine_service_any+0x76/0x84 [ath10k_core]
[21713.800310] ath10k_pci_napi_poll+0x49/0x144 [ath10k_pci]
[21713.800316] net_rx_action+0xdc/0x361
[21713.800320] __do_softirq+0x163/0x29a
[21713.800325] asm_call_irq_on_stack+0x12/0x20
[21713.800331] do_softirq_own_stack+0x3c/0x48
[21713.800337] __irq_exit_rcu+0x9b/0x9d
[21713.800342] common_interrupt+0xc9/0x14d
[21713.800346] asm_common_interrupt+0x1e/0x40
[21713.800351] ksoftirqd_should_run+0x5/0x16
[21713.800357] smpboot_thread_fn+0x148/0x211
[21713.800362] kthread+0x150/0x15f
[21713.800367] ret_from_fork+0x22/0x30
[21713.800370]
[21713.800374] freed by task 708 on cpu 1 at 21713.799953s:
[21713.800498] ath10k_sta_state+0x2c6/0xb8a [ath10k_core]
[21713.800515] drv_sta_state+0x115/0x677 [mac80211]
[21713.800532] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800548] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800565] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800581] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800598] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800614] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800619] genl_rcv_msg+0x38e/0x3be
[21713.800623] netlink_rcv_skb+0x89/0xf7
[21713.800628] genl_rcv+0x28/0x36
[21713.800632] netlink_unicast+0x179/0x24b
[21713.800637] netlink_sendmsg+0x3a0/0x40e
[21713.800642] sock_sendmsg+0x72/0x76
[21713.800646] ____sys_sendmsg+0x16d/0x1e3
[21713.800651] ___sys_sendmsg+0x95/0xd1
[21713.800655] __sys_sendmsg+0x85/0xbf
[21713.800659] do_syscall_64+0x43/0x55
[21713.800663] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: d0eeafad1189 ("ath10k: Clean up peer when sta goes away.") Signed-off-by: Wen Gong <quic_wgong@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220801141930.16794-1-quic_wgong@quicinc.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Since IQK could spend time, we make a cache of IQK result matrix that looks
like iqk_matrix[channel_idx].val[x][y], and we can reload the matrix if we
have made a cache. To determine a cache is made, we check
iqk_matrix[channel_idx].val[0][0].
The initial commit 7274a8c22980 ("rtlwifi: rtl8192de: Merge phy routines")
make a mistake that checks incorrect iqk_matrix[channel_idx].val[0] that
is always true, and this mistake is found by commit ee3db469dd31
("wifi: rtlwifi: remove always-true condition pointed out by GCC 12"), so
I recall the vendor driver to find fix and apply the correctness.
The "testb" here is using %dil, but the %rdi register was cleared before
returning from "callq *pv_ops+536(%rip)". Adding the proper constraints
results in the use of a different register:
If an NFS server returns NFS4ERR_RESOURCE on the first operation in
an NFSv4 COMPOUND, there's no way for a client to know where the
problem is and then simplify the compound to make forward progress.
So instead, make NFSD process as many operations in an oversized
COMPOUND as it can and then return NFS4ERR_RESOURCE on the first
operation it did not process.
pynfs NFSv4.0 COMP6 exercises this case, but checks only for the
COMPOUND status code, not whether the server has processed any
of the operations.
pynfs NFSv4.1 SEQ6 and SEQ7 exercise the NFSv4.1 case, which detects
too many operations per COMPOUND by checking against the limits
negotiated when the session was created.
Suggested-by: Bruce Fields <bfields@fieldses.org> Fixes: 0078117c6d91 ("nfsd: return RESOURCE not GARBAGE_ARGS on too many ops") Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 2825a7f90753 ("nfsd4: allow encoding across page boundaries")
added an explicit computation of the remaining length in the rq_res
XDR buffer.
The computation appears to suffer from an "off-by-one" bug. Because
buflen is too large by one page, XDR encoding can run off the end of
the send buffer by eventually trying to use the struct page address
in rq_page_end, which always contains NULL.
Fixes: bddfdbcddbe2 ("NFSD: Extract the svcxdr_init_encode() helper") Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that stream-based argument decoding can't go past the actual
end of the receive buffer. xdr_init_decode's calculation of the
value of xdr->end over-estimates the end of the buffer because the
Linux kernel RPC server code does not remove the size of the RPC
header from rqstp->rq_arg before calling the upper layer's
dispatcher.
The server-side still uses the svc_getnl() macros to decode the
RPC call header. These macros reduce the length of the head iov
but do not update the total length of the message in the buffer
(buf->len).
A proper fix for this would be to replace the use of svc_getnl() and
friends in the RPC header decoder, but that would be a large and
invasive change that would be difficult to backport.
Fixes: 5191955d6fc6 ("SUNRPC: Prepare for xdr_stream-style decoding on the server-side") Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If this memdup_user() call fails, the memory allocated in a previous call
a few lines above should be freed. Otherwise it leaks.
Fixes: 6ee95d1c8991 ("nfsd: add support for upcall version 2") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
elf_update_symbol fails to preserve the special st_shndx values
between [SHN_LORESERVE, SHN_HIRESERVE], which results in it
converting SHN_ABS entries into SHN_UNDEF, for example. Explicitly
check for the special indexes and ensure these symbols are not
marked undefined.
Fixes: ead165fa1042 ("objtool: Fix symbol creation") Signed-off-by: Sami Tolvanen <samitolvanen@google.com> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20220908215504.3686827-17-samitolvanen@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, mbox_client_txdone() is called from the PCC address space
handler and that expects the user the Tx state machine to be controlled
by the client which is not the case and the below warning is thrown:
| PCCT: Client can't run the TX ticker
Let the controller run the state machine and the end of Tx can be
acknowledge by calling mbox_chan_txdone() instead.
Fixes: 77e2a04745ff ("ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype") Signed-off-by: Huisong Li <lihuisong@huawei.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the function waiting for completion of mailbox operation is
'wait_for_completion()'. The PCC method will be permanently blocked if
this mailbox message fails to execute. So this patch replaces it with
'wait_for_completion_timeout()'. And set the timeout interval to an
arbitrary retries on top of nominal to prevent the remote processor is
slow to respond to PCC commands.
Fixes: 77e2a04745ff ("ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype") Signed-off-by: Huisong Li <lihuisong@huawei.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The allocated memory for the pcc_data struct doesn't get freed under an
error path in pcc_mbox_request_channel() or acpi_os_ioremap(). Also, the
PCC mailbox channel doesn't get freed under an error path in
acpi_os_ioremap().
Fixes: 77e2a04745ff8 ("ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype") Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
MT_MEMORY_RO is introduced by commit 598f0a99fa8a ("ARM: 9210/1:
Mark the FDT_FIXED sections as shareable"), which is a readonly
memory type for FDT area, but there are some different between
ARM_LPAE and non-ARM_LPAE, we need to setup PMD_SECT_AP2 and
L_PMD_SECT_RDONLY for MT_MEMORY_RO when ARM_LAPE enabled.
Fixes: 598f0a99fa8a ("ARM: 9210/1: Mark the FDT_FIXED sections as shareable") Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
After ARM supports p4d page tables, the pg_level for note_page()
in walk_pmd() should be 4, not 3, fix it.
Fixes: 84e6ffb2c49c ("arm: add support for folded p4d page tables") Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
In file included from ./include/linux/io.h:13,
from ./arch/arm/mach-rpc/include/mach/uncompress.h:9,
from arch/arm/boot/compressed/misc.c:31:
./arch/arm/include/asm/io.h:85:22: error: conflicting types for ‘__raw_writeb’
85 | #define __raw_writeb __raw_writeb
| ^~~~~~~~~~~~
./arch/arm/include/asm/io.h:86:20: note: in expansion of macro ‘__raw_writeb’
86 | static inline void __raw_writeb(u8 val, volatile void __iomem *addr)
| ^~~~~~~~~~~~
In file included from arch/arm/boot/compressed/misc.c:26:
arch/arm/boot/compressed/misc-ep93xx.h:13:20: note: previous definition of ‘__raw_writeb’ was here
13 | static inline void __raw_writeb(unsigned char value, unsigned int ptr)
| ^~~~~~~~~~~~
To: Russell King <linux@armlinux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de> Cc: linux-arm-kernel@lists.infradead.org Fixes: 0361c7e504b1 ("ARM: ep93xx: multiplatform support") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use kill_anon_super() instead of generic_shutdown_super() since the
mount() in erofs fscache mode uses get_tree_nodev() and associated
anon bdev needs to be freed.
As syzbot reported [1], the root cause is that i_size field is a
signed type, and negative i_size is also less than EROFS_BLKSIZ.
As a consequence, it's handled as fast symlink unexpectedly.
Let's fall back to the generic path to deal with such unusual i_size.
In error case in bridge_platform_create after calling
platform_device_add()/platform_device_add_data()/
platform_device_add_resources(), release the failed
'pdev' or it will be leak, call platform_device_put()
to fix this problem.
Besides, 'pdev' is divided into 'pdev_wd' and 'pdev_bd',
use platform_device_unregister() to release sgi_w1
resources when xtalk-bridge registration fails.
Fixes: 5dc76a96e95a ("MIPS: PCI: use information from 1-wire PROM for IOC3 detection") Signed-off-by: Lin Yujun <linyujun809@huawei.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In error case in bridge_platform_create after calling
platform_device_add()/platform_device_add_data()/
platform_device_add_resources(), release the failed
'pdev' or it will be leak, call platform_device_put()
to fix this problem.
Besides, 'pdev' is divided into 'pdev_wd' and 'pdev_bd',
use platform_device_unregister() to release sgi_w1
resources when xtalk-bridge registration fails.
Fixes: fd27234f24ae ("MIPS: add support for SGI Octane (IP30)") Signed-off-by: Lin Yujun <linyujun809@huawei.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
As done for other sections, define the extern as a character array,
which relaxes many of the compiler-time object size checks, which would
otherwise assume it's a single long. Solves the following build error:
arch/sh/kernel/machvec.c: error: array subscript 'struct sh_machine_vector[0]' is partly outside array bounds of 'long int[1]' [-Werror=array-bounds]: => 105:33
To avoid some new AMD processors use wrong highest perf when amd pstate
driver loaded, this fix will query the highest perf from MSR register
MSR_AMD_CPPC_CAP1 and cppc_acpi interface firstly, then compare with the
highest perf value got by calling amd_get_highest_perf() function.
The lower value will be the correct highest perf we need to use.
Otherwise the CPU max MHz will be incorrect if the
amd_get_highest_perf() did not cover the new process family and model ID.
Like this lscpu info, the max frequency is incorrect.
Vendor ID: AuthenticAMD
Socket(s): 1
Stepping: 2
CPU max MHz: 5410.0000
CPU min MHz: 400.0000
BogoMIPS: 5600.54
Fixes: 3743d55b289c2 (x86, sched: Fix the AMD CPPC maximum performance value on certain AMD Ryzen generations) Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Perry Yuan <Perry.Yuan@amd.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The xattr code in ntfs3 is currently a bit confused. For example, it
defines a POSIX ACL i_op->set_acl() method but instead of relying on the
generic POSIX ACL VFS helpers it defines its own set of xattr helpers
with the consequence that i_op->set_acl() is currently dead code.
Switch ntfs3 to rely on the VFS POSIX ACL xattr handlers. Also remove
i_op->{g,s}et_acl() methods from symlink inode operations. Symlinks
don't support xattrs.
This is a preliminary change for the following patches which move
handling idmapped mounts directly in posix_acl_xattr_set().
Since userfaultfd doesn't implement a write operation, it is more
appropriate to open it read-only.
When userfaultfds are opened read-write like it is now, and such fd is
passed from one process to another, SELinux will check both read and
write permissions for the target process, even though it can't actually
do any write operation on the fd later.
Inspired by the following bug report, which has hit the SELinux scenario
described above:
https://bugzilla.redhat.com/show_bug.cgi?id=1974559
Reported-by: Robert O'Callahan <roc@ocallahan.org> Fixes: 86039bd3b4e6 ("userfaultfd: add new syscall to provide memory externalization") Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Limit validating the hash algorithm to just security.ima xattr, not
the security.evm xattr or any of the protected EVM security xattrs,
nor posix acls.
Fixes: 50f742dd9147 ("IMA: block writes of the security.ima xattr with unsupported algorithms") Reported-by: Christian Brauner <brauner@kernel.org> Acked-by: Christian Brauner (Microsoft) <brauner@kernel.org> Signed-off-by: Mimi Zohar <zohar@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The latest version of grep claims that egrep is now obsolete so the build
now contains warnings that look like:
egrep: warning: egrep is obsolescent; using grep -E
fix this by using "grep -E" instead.
Cc: Paul Moore <paul@paul-moore.com> Cc: Stephen Smalley <stephen.smalley.work@gmail.com> Cc: Eric Paris <eparis@parisplace.org> Cc: selinux@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[PM: tweak to remove vdso reference, cleanup subj line] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
manage_dm_interrupts disable/enable vblank using drm_crtc_vblank_off/on
which causes drm_crtc_vblank_get in vrr_transition to fail, and later
when drm_crtc_vblank_put is called the refcount on vblank will be messed
up. Therefore move the call to after manage_dm_interrupts.
projects / thirdparty / kernel / stable.git / log
