According to the datasheet you should only write 1 to this bit. If it is
not set, at least AIN3 will return bad values on newer silicon revisions.
Fixes: d84ca5b345c2 ("hwmon: Add driver for ADT7411 voltage and temperature sensor") Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Whilst MPIDR values themselves are less than 32 bits, it is still
perfectly valid for a DT to have #address-cells > 1 in the CPUs node,
resulting in the "reg" property having leading zero cell(s). In that
situation, the big-endian nature of the data conspires with the current
behaviour of only reading the first cell to cause the kernel to think
all CPUs have ID 0, and become resoundingly unhappy as a consequence.
Take the full property length into account when parsing CPUs so as to
be correct under any circumstances.
Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
A timer was used to restart after the bus-off state, leading to a
relatively large can_restart() executed in an interrupt context,
which in turn sets up pinctrl. When this happens during system boot,
there is a high probability of grabbing the pinctrl_list_mutex,
which is locked already by the probe() of other device, making the
kernel suspect a deadlock condition [1].
To resolve this issue, the restart_timer is replaced by a delayed
work.
The oom victim cannot terminate because it needs to take mmap_sem for
write while the lock is held by ksmd for read which loops in the page
allocator
ksm_do_scan
scan_get_next_rmap_item
down_read
get_next_rmap_item
alloc_rmap_item #ksmd will loop permanently.
There is no way forward because the oom victim cannot release any memory
in 4.1 based kernel. Since 4.6 we have the oom reaper which would solve
this problem because it would release the memory asynchronously.
Nevertheless we can relax alloc_rmap_item requirements and use
__GFP_NORETRY because the allocation failure is acceptable as ksm_do_scan
would just retry later after the lock got dropped.
Such a patch would be also easy to backport to older stable kernels which
do not have oom_reaper.
While we are at it add GFP_NOWARN so the admin doesn't have to be alarmed
by the allocation failure.
This fixes subpage writes when using 4-bit HW ECC.
There has been numerous reports about ECC errors with devices using this
driver for a while. Also the 4-bit ECC has been reported as broken with
subpages in [1] and with 16 bits NANDs in the driver and in mach* board
files both in mainline and in the vendor BSPs.
What I saw with 4-bit ECC on a 16bits NAND (on an LCDK) which got me to
try reinitializing the ECC engine:
- R/W on whole pages properly generates/checks RS code
- try writing the 1st subpage only of a blank page, the subpage is well
written and the RS code properly generated, re-reading the same page
the HW detects some ECC error, reading the same page again no ECC
error is detected
Note that the ECC engine is already reinitialized in the 1-bit case.
Tested on my LCDK with UBI+UBIFS using subpages.
This could potentially get rid of the issue workarounded in [1].
[1] 28c015a9daab ("mtd: davinci-nand: disable subpage write for keystone-nand")
Fixes: 6a4123e581b3 ("mtd: nand: davinci_nand, 4-bit ECC for smallpage") Signed-off-by: Karl Beldan <kbeldan@baylibre.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The encoding of the lengths in the ibm_architecture_vec array is
"interesting" to say the least. It's non-obvious how the number of bytes
we provide relates to the length value.
In fact we already got it wrong once, see 11e9ed43ca8a "Fix up
ibm_architecture_vec definition".
So add some macros to make it (hopefully) clearer. These at least have
the property that the integer present in the code is equal to the number
of bytes that follows it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Reviewed-by: Stewart Smith <stewart@linux.vnet.ibm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Oleg noticed that its possible to falsely observe p->on_cpu == 0 such
that we'll prematurely continue with the wakeup and effectively run p on
two CPUs at the same time.
Even though the overlap is very limited; the task is in the middle of
being scheduled out; it could still result in corruption of the
scheduler data structures.
Jeff Mahoney [Thu, 6 Oct 2016 06:18:16 +0000 (08:18 +0200)]
xfs: fixed signedness of error code in xfs_inode_buf_verify
Prior to v3.17, XFS used positive error codes internally. Commit af8d971602b9583e5e8400e637e2a48c7480bc64 (xfs: inode recovery
readahead can race with inode buffer creation), upstream commit b79f4a1c68bb99152d0785ee4ea3ab4396cdacc6 backported from later
releases need the error code signs reversed. Negative error codes
will cause assertion failures (BUG_ON on kernels with assertions
enabled.
Signed-off-by: Jeff Mahoney <jeffm@suse.com> Cc: Dave Chinner <dchinner@redhat.com> Cc: Brian Foster <bfoster@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Let the target core check task existence instead of the SRP target
driver. Additionally, let the target core check the validity of the
task management request instead of the ib_srpt driver.
Commit fec1d0115240 ("[PATCH] Disable CLONE_CHILD_CLEARTID for abnormal
exit") has caused a subtle regression in nscd which uses
CLONE_CHILD_CLEARTID to clear the nscd_certainly_running flag in the
shared databases, so that the clients are notified when nscd is
restarted. Now, when nscd uses a non-persistent database, clients that
have it mapped keep thinking the database is being updated by nscd, when
in fact nscd has created a new (anonymous) one (for non-persistent
databases it uses an unlinked file as backend).
The original proposal for the CLONE_CHILD_CLEARTID change claimed
(https://lkml.org/lkml/2006/10/25/233):
: The NPTL library uses the CLONE_CHILD_CLEARTID flag on clone() syscalls
: on behalf of pthread_create() library calls. This feature is used to
: request that the kernel clear the thread-id in user space (at an address
: provided in the syscall) when the thread disassociates itself from the
: address space, which is done in mm_release().
:
: Unfortunately, when a multi-threaded process incurs a core dump (such as
: from a SIGSEGV), the core-dumping thread sends SIGKILL signals to all of
: the other threads, which then proceed to clear their user-space tids
: before synchronizing in exit_mm() with the start of core dumping. This
: misrepresents the state of process's address space at the time of the
: SIGSEGV and makes it more difficult for someone to debug NPTL and glibc
: problems (misleading him/her to conclude that the threads had gone away
: before the fault).
:
: The fix below is to simply avoid the CLONE_CHILD_CLEARTID action if a
: core dump has been initiated.
The resulting patch from Roland (https://lkml.org/lkml/2006/10/26/269)
seems to have a larger scope than the original patch asked for. It
seems that limitting the scope of the check to core dumping should work
for SIGSEGV issue describe above.
[Changelog partly based on Andreas' description] Fixes: fec1d0115240 ("[PATCH] Disable CLONE_CHILD_CLEARTID for abnormal exit") Link: http://lkml.kernel.org/r/1471968749-26173-1-git-send-email-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Tested-by: William Preston <wpreston@suse.com> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Roland McGrath <roland@hack.frob.com> Cc: Andreas Schwab <schwab@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It looks like clockevents_unbind is being exported by mistake as:
- it is static;
- it is not listed in include/linux/clockchips.h;
- EXPORT_SYMBOL_GPL(clockevents_unbind) follows clockevents_unbind_device()
implementation.
I think clockevents_unbind_device should be exported instead. This is going to
be used to teardown Hyper-V clockevent devices on module unload.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Not doing so might cause IO-Page-Faults when a device uses
an alias request-id and the alias-dte is left in a lower
page-mode which does not cover the address allocated from
the iova-allocator.
Matt reported that we have a NULL pointer dereference
in ppp_pernet() from ppp_connect_channel(),
i.e. pch->chan_net is NULL.
This is due to that a parallel ppp_unregister_channel()
could happen while we are in ppp_connect_channel(), during
which pch->chan_net set to NULL. Since we need a reference
to net per channel, it makes sense to sync the refcnt
with the life time of the channel, therefore we should
release this reference when we destroy it.
Fixes: 1f461dcdd296 ("ppp: take reference on channels netns") Reported-by: Matt Bennett <Matt.Bennett@alliedtelesis.co.nz> Cc: Paul Mackerras <paulus@samba.org> Cc: linux-ppp@vger.kernel.org Cc: Guillaume Nault <g.nault@alphalink.fr> Cc: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Reviewed-by: Cyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
gcc-6 correctly warns about a out of bounds access
arch/powerpc/kernel/ptrace.c:407:24: warning: index 32 denotes an offset greater than size of 'u64[32][1] {aka long long unsigned int[32][1]}' [-Warray-bounds]
offsetof(struct thread_fp_state, fpr[32][0]));
^
check the end of array instead of beginning of next element to fix this
Signed-off-by: Khem Raj <raj.khem@gmail.com> Cc: Kees Cook <keescook@chromium.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Segher Boessenkool <segher@kernel.crashing.org> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix headers_install by adjusting the path to arch files.
And delete unused Kbuild file.
Drop special handling of cris in the headers.sh script
as a nice side-effect.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Cc: Mikael Starvik <starvik@axis.com> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
The origin of the issue I've seen is related to
a missing memory barrier between check for task->state and
the check for task->on_rq.
The task being woken up is already awake from a schedule()
and is doing the following:
do {
schedule()
set_current_state(TASK_(UN)INTERRUPTIBLE);
} while (!cond);
The waker, actually gets stuck doing the following in
try_to_wake_up():
while (p->on_cpu)
cpu_relax();
Analysis:
The instance I've seen involves the following race:
CPU1 CPU2
while () {
if (cond)
break;
do {
schedule();
set_current_state(TASK_UN..)
} while (!cond);
wakeup_routine()
spin_lock_irqsave(wait_lock)
raw_spin_lock_irqsave(wait_lock) wake_up_process()
} try_to_wake_up()
set_current_state(TASK_RUNNING); ..
list_del(&waiter.list);
CPU2 wakes up CPU1, but before it can get the wait_lock and set
current state to TASK_RUNNING the following occurs:
CPU3
wakeup_routine()
raw_spin_lock_irqsave(wait_lock)
if (!list_empty)
wake_up_process()
try_to_wake_up()
raw_spin_lock_irqsave(p->pi_lock)
..
if (p->on_rq && ttwu_wakeup())
..
while (p->on_cpu)
cpu_relax()
..
CPU3 tries to wake up the task on CPU1 again since it finds
it on the wait_queue, CPU1 is spinning on wait_lock, but immediately
after CPU2, CPU3 got it.
CPU3 checks the state of p on CPU1, it is TASK_UNINTERRUPTIBLE and
the task is spinning on the wait_lock. Interestingly since p->on_rq
is checked under pi_lock, I've noticed that try_to_wake_up() finds
p->on_rq to be 0. This was the most confusing bit of the analysis,
but p->on_rq is changed under runqueue lock, rq_lock, the p->on_rq
check is not reliable without this fix IMHO. The race is visible
(based on the analysis) only when ttwu_queue() does a remote wakeup
via ttwu_queue_remote. In which case the p->on_rq change is not
done uder the pi_lock.
The result is that after a while the entire system locks up on
the raw_spin_irqlock_save(wait_lock) and the holder spins infintely
Reproduction of the issue:
The issue can be reproduced after a long run on my system with 80
threads and having to tweak available memory to very low and running
memory stress-ng mmapfork test. It usually takes a long time to
reproduce. I am trying to work on a test case that can reproduce
the issue faster, but thats work in progress. I am still testing the
changes on my still in a loop and the tests seem OK thus far.
Big thanks to Benjamin and Nick for helping debug this as well.
Ben helped catch the missing barrier, Nick caught every missing
bit in my theory.
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
[ Updated comment to clarify matching barriers. Many
architectures do not have a full barrier in switch_to()
so that cannot be relied upon. ] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alexey Kardashevskiy <aik@ozlabs.ru> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nicholas Piggin <nicholas.piggin@gmail.com> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/e02cce7b-d9ca-1ad0-7a61-ea97c7582b37@gmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
If the subvol/snapshot create/destroy ioctls are passed a regular file
with execute permissions set, we'll eventually Oops while trying to do
inode->i_op->lookup via lookup_one_len.
This patch ensures that the file descriptor refers to a directory.
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
The iter->seq can be reset outside the protection of the mutex. So can
reading of user data. Move the mutex up to the beginning of the function.
Fixes: d7350c3f45694 ("tracing/core: make the read callbacks reentrants") Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
There is a cut and paste issue here. The bug is that we are allocating
more memory than necessary for msp_maps. We should be allocating enough
space for a map_info struct (144 bytes) but we instead allocate enough
for an mtd_info struct (1840 bytes). It's a small waste.
The other part of this is not harmful but when we allocated msp_flash
then we allocated enough space fro a map_info pointer instead of an
mtd_info pointer. But since pointers are the same size it works out
fine.
Anyway, I decided to clean up all three allocations a bit to make them
a bit more consistent and clear.
Fixes: 68aa0fa87f6d ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Switching iov_iter fault-in to multipages variants has exposed an old
bug in underlying fault_in_multipages_...(); they break if the range
passed to them wraps around. Normally access_ok() done by callers will
prevent such (and it's a guaranteed EFAULT - ERR_PTR() values fall into
such a range and they should not point to any valid objects).
However, on architectures where userland and kernel live in different
MMU contexts (e.g. s390) access_ok() is a no-op and on those a range
with a wraparound can reach fault_in_multipages_...().
Since any wraparound means EFAULT there, the fix is trivial - turn
those
while (uaddr <= end)
...
into
if (unlikely(uaddr > end))
return -EFAULT;
do
...
while (uaddr <= end);
Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fix indent warning when building with gcc 6:
drivers/staging/iio/adc/ad7192.c:239:4: warning: statement is indented
as if it were guarded by... [-Wmisleading-indentation]
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
gcc points out code that is not indented the way it is
interpreted:
net/caif/cfpkt_skbuff.c: In function 'cfpkt_setlen':
net/caif/cfpkt_skbuff.c:289:4: error: statement is indented as if it were guarded by... [-Werror=misleading-indentation]
return cfpkt_getlen(pkt);
^~~~~~
net/caif/cfpkt_skbuff.c:286:3: note: ...this 'else' clause, but it is not
else
^~~~
It is clear from the context that not returning here would be
a bug, as we'd end up passing a negative length into a function
that takes a u16 length, so it is not missing curly braces
here, and I'm assuming that the indentation is the only part
that's wrong about it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
With the latest gcc compilers, they give a warning if
__builtin_return_address() parameter is greater than 0. That is because if
it is used by a function called by a top level function (or in the case of
the kernel, by assembly), it can try to access stack frames outside the
stack and crash the system.
The tracing system uses __builtin_return_address() of up to 2! But it is
well aware of the dangers that it may have, and has even added precautions
to protect against it (see the thunk code in arch/x86/entry/thunk*.S)
Linus originally added KBUILD_CFLAGS that would suppress the warning for the
entire kernel, as simply adding KBUILD_CFLAGS to the tracing directory
wouldn't work. The tracing directory plays a bit with the CFLAGS and
requires a little more logic.
This adds that special logic to only suppress the warning for the tracing
directory. If it is used anywhere else outside of tracing, the warning will
still be triggered.
Newer versions of gcc warn about the use of __builtin_return_address()
with a non-zero argument when "-Wall" is specified:
kernel/trace/trace_irqsoff.c: In function ‘stop_critical_timings’:
kernel/trace/trace_irqsoff.c:433:86: warning: calling ‘__builtin_return_address’ with a nonzero argument is unsafe [-Wframe-address]
stop_critical_timing(CALLER_ADDR0, CALLER_ADDR1);
[ .. repeats a few times for other similar cases .. ]
It is true that a non-zero argument is somewhat dangerous, and we do not
actually have very many uses of that in the kernel - but the ftrace code
does use it, and as Stephen Rostedt says:
"We are well aware of the danger of using __builtin_return_address() of
> 0. In fact that's part of the reason for having the "thunk" code in
x86 (See arch/x86/entry/thunk_{64,32}.S). [..] it adds extra frames
when tracking irqs off sections, to prevent __builtin_return_address()
from accessing bad areas. In fact the thunk_32.S states: 'Trampoline to
trace irqs off. (otherwise CALLER_ADDR1 might crash)'."
For now, __builtin_return_address() with a non-zero argument is the best
we can do, and the warning is not helpful and can end up making people
miss other warnings for real problems.
So disable the frame-address warning on compilers that need it.
Several build configurations had already disabled this warning because
it generates a lot of false positives. But some had not, and it was
still enabled for "allmodconfig" builds, for example.
Looking at the warnings produced, every single one I looked at was a
false positive, and the warnings are frequent enough (and big enough)
that they can easily hide real problems that you don't notice in the
noise generated by -Wmaybe-uninitialized.
The warning is good in theory, but this is a classic case of a warning
that causes more problems than the warning can solve.
If gcc gets better at avoiding false positives, we may be able to
re-enable this warning. But as is, we're better off without it, and I
want to be able to see the *real* warnings.
When gcov profiling is enabled, we see a lot of spurious warnings about
possibly uninitialized variables being used:
arch/arm/mm/dma-mapping.c: In function 'arm_coherent_iommu_map_page':
arch/arm/mm/dma-mapping.c:1085:16: warning: 'start' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/clk/st/clk-flexgen.c: In function 'st_of_flexgen_setup':
drivers/clk/st/clk-flexgen.c:323:9: warning: 'num_parents' may be used uninitialized in this function [-Wmaybe-uninitialized]
kernel/cgroup.c: In function 'cgroup_mount':
kernel/cgroup.c:2119:11: warning: 'root' may be used uninitialized in this function [-Wmaybe-uninitialized]
All of these are false positives, so it seems better to just disable
the warnings whenever GCOV is enabled. Most users don't enable GCOV,
and based on a prior patch, it is now also disabled for 'allmodconfig'
builds, so there should be no downsides of doing this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
CONFIG_PROFILE_ALL_BRANCHES confuses gcc-5.x to the degree that it prints
incorrect warnings about a lot of variables that it thinks can be used
uninitialized, e.g.:
i2c/busses/i2c-diolan-u2c.c: In function 'diolan_usb_xfer':
i2c/busses/i2c-diolan-u2c.c:391:16: warning: 'byte' may be used uninitialized in this function
iio/gyro/itg3200_core.c: In function 'itg3200_probe':
iio/gyro/itg3200_core.c:213:6: warning: 'val' may be used uninitialized in this function
leds/leds-lp55xx-common.c: In function 'lp55xx_update_bits':
leds/leds-lp55xx-common.c:350:6: warning: 'tmp' may be used uninitialized in this function
misc/bmp085.c: In function 'show_pressure':
misc/bmp085.c:363:10: warning: 'pressure' may be used uninitialized in this function
power/ds2782_battery.c: In function 'ds2786_get_capacity':
power/ds2782_battery.c:214:17: warning: 'raw' may be used uninitialized in this function
These are all false positives that either rob someone's time when trying
to figure out whether they are real, or they get people to send wrong
patches to shut up the warnings.
Nobody normally wants to run a CONFIG_PROFILE_ALL_BRANCHES kernel in
production, so disabling the whole class of warnings for this configuration
has no serious downsides either.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Steven Rostedt <rostedtgoodmis.org> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When the kernel path contains a space or a colon somewhere in the path
name, the modules_install target doesn't work anymore, as the path names
are not enclosed in double quotes. It is also supposed that and O= build
will suffer from the same weakness as modules_install.
Instead of checking and improving kbuild to resist to directories
including these characters, error out early to prevent any build if the
kernel's main directory contains a space.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 627189797807 ("Makefile: Document ability to make file.lst
and file.S") document ability to make file.S, but there isn't such
ability in kbuild, so revert it.
Signed-off-by: Wang YanQing <udknight@gmail.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
If we punch a hole on a reflink such that following conditions are met:
1. start offset is on a cluster boundary
2. end offset is not on a cluster boundary
3. (end offset is somewhere in another extent) or
(hole range > MAX_CONTIG_BYTES(1MB)),
we dont COW the first cluster starting at the start offset. But in this
case, we were wrongly passing this cluster to
ocfs2_zero_range_for_truncate() to zero out. This will modify the
cluster in place and zero it in the source too.
Fix this by skipping this cluster in such a scenario.
To reproduce:
1. Create a random file of say 10 MB
xfs_io -c 'pwrite -b 4k 0 10M' -f 10MBfile
2. Reflink it
reflink -f 10MBfile reflnktest
3. Punch a hole at starting at cluster boundary with range greater that
1MB. You can also use a range that will put the end offset in another
extent.
fallocate -p -o 0 -l 1048615 reflnktest
4. sync
5. Check the first cluster in the source file. (It will be zeroed out).
dd if=10MBfile iflag=direct bs=<cluster size> count=1 | hexdump -C
Link: http://lkml.kernel.org/r/1470957147-14185-1-git-send-email-ashish.samant@oracle.com Signed-off-by: Ashish Samant <ashish.samant@oracle.com> Reported-by: Saar Maoz <saar.maoz@oracle.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Eric Ren <zren@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery")
checks if lockres master has changed to identify whether new master has
finished recovery or not. This will introduce a race that right after
old master does umount ( means master will change), a new convert
request comes.
In this case, it will reset lockres state to DLM_RECOVERING and then
retry convert, and then fail with lockres->l_action being set to
OCFS2_AST_INVALID, which will cause inconsistent lock level between
ocfs2 and dlm, and then finally BUG.
Since dlm recovery will clear lock->convert_pending in
dlm_move_lockres_to_recovery_list, we can use it to correctly identify
the race case between convert and recovery. So fix it.
Fixes: ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery") Link: http://lkml.kernel.org/r/57CE1569.8010704@huawei.com Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@versity.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When we need to allocate a temporary blkcipher_walk_next and it
fails, the code is supposed to take the slow path of processing
the data block by block. However, due to an unrelated change
we instead end up dereferencing the NULL pointer.
This patch fixes it by moving the unrelated bsize setting out
of the way so that we enter the slow path as inteded.
new_insert_key only makes any sense when it's associated with a
new_insert_ptr, which is initialized to NULL and changed to a
buffer_head when we also initialize new_insert_key. We can key off of
that to avoid the uninitialized warning.
Link: http://lkml.kernel.org/r/5eca5ffb-2155-8df2-b4a2-f162f105efed@suse.com Signed-off-by: Jeff Mahoney <jeffm@suse.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jan Kara <jack@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Enabling CONFIG_GCOV_PROFILE_ALL produces us a lot of warnings like
lib/lz4/lz4hc_compress.c: In function 'lz4_compresshcctx':
lib/lz4/lz4hc_compress.c:514:1: warning: the frame size of 1504 bytes is larger than 1024 bytes [-Wframe-larger-than=]
After some investigation, I found that this behavior started with gcc-4.9,
and opened https://gcc.gnu.org/bugzilla/show_bug.cgi?id=69702.
A suggested workaround for it is to use the -fno-tree-loop-im
flag that turns off one of the optimization stages in gcc, so the
code runs a little slower but does not use excessive amounts
of stack.
We could make this conditional on the gcc version, but I could not
find an easy way to do this in Kbuild and the benefit would be
fairly small, given that most of the gcc version in production are
affected now.
I'm marking this for 'stable' backports because it addresses a bug
with code generation in gcc that exists in all kernel versions
with the affected gcc releases.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com> Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Since commit acb2505d0119 ("openrisc: fix copy_from_user()"),
copy_from_user() returns the number of bytes requested, not the
number of bytes not copied.
arch/avr32/kernel/built-in.o: In function `arch_ptrace':
(.text+0x650): undefined reference to `___copy_from_user'
arch/avr32/kernel/built-in.o:(___ksymtab+___copy_from_user+0x0): undefined
reference to `___copy_from_user'
kernel/built-in.o: In function `proc_doulongvec_ms_jiffies_minmax':
(.text+0x5dd8): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `proc_dointvec_minmax_sysadmin':
sysctl.c:(.text+0x6174): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `ptrace_has_cap':
ptrace.c:(.text+0x69c0): undefined reference to `___copy_from_user'
kernel/built-in.o:ptrace.c:(.text+0x6b90): more undefined references to
`___copy_from_user' follow
... that should zero on faults. Also remove the <censored> helpful
logics wrt range truncation copied from ppc32. Where it had ever
been needed only in case of copy_from_user() *and* had not been merged
into the mainline until a month after the need had disappeared.
A decade before openrisc went into mainline, I might add...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
... in all cases, including the failing access_ok()
Note that some architectures using asm-generic/uaccess.h have
__copy_from_user() not zeroing the tail on failure halfway
through. This variant works either way.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
* copy_from_user() on access_ok() failure ought to zero the destination
* none of those primitives should skip the access_ok() check in case of
small constant size.
It could be done in exception-handling bits in __get_user_b() et.al.,
but the surgery involved would take more knowledge of sh64 details
than I have or _want_ to have.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
get_user_ex(x, ptr) should zero x on failure. It's not a lot of a leak
(at most we are leaking uninitialized 64bit value off the kernel stack,
and in a fairly constrained situation, at that), but the fix is trivial,
so...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ This sat in different branch from the uaccess fixes since mid-August ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
really ugly, but apparently avr32 compilers turns access_ok() into
something so bad that they want it in assembler. Left that way,
zeroing added in inline wrapper.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
When calling .import() on a cryptd ahash_request, the structure members
that describe the child transform in the shash_desc need to be initialized
like they are when calling .init()
smp_mb__before_spinlock() is intended to upgrade a spin_lock() operation
to a full barrier, such that prior stores are ordered with respect to
loads and stores occuring inside the critical section.
Unfortunately, the core code defines the barrier as smp_wmb(), which
is insufficient to provide the required ordering guarantees when used in
conjunction with our load-acquire-based spinlock implementation.
This patch overrides the arm64 definition of smp_mb__before_spinlock()
to map to a full smp_mb().
Cc: Peter Zijlstra <peterz@infradead.org> Reported-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Some full-speed mceusb infrared transceivers contain invalid endpoint
descriptors for their interrupt endpoints, with bInterval set to 0.
In the past they have worked out okay with the mceusb driver, because
the driver sets the bInterval field in the descriptor to 1,
overwriting whatever value may have been there before. However, this
approach was never sanctioned by the USB core, and in fact it does not
work with xHCI controllers, because they use the bInterval value that
was present when the configuration was installed.
Currently usbcore uses 32 ms as the default interval if the value in
the endpoint descriptor is invalid. It turns out that these IR
transceivers don't work properly unless the interval is set to 10 ms
or below. To work around this mceusb problem, this patch changes the
endpoint-descriptor parsing routine, making the default interval value
be 10 ms rather than 32 ms.
The previous driver is possible to stop the transfer wrongly.
For example:
1) An interrupt happens, but not BRDY interruption.
2) Read INTSTS0. And than state->intsts0 is not set to BRDY.
3) BRDY is set to 1 here.
4) Read BRDYSTS.
5) Clear the BRDYSTS. And then. the BRDY is cleared wrongly.
Remarks:
- The INTSTS0.BRDY is read only.
- If any bits of BRDYSTS are set to 1, the BRDY is set to 1.
- If BRDYSTS is 0, the BRDY is set to 0.
So, this patch adds condition to avoid such situation. (And about
NRDYSTS, this is not used for now. But, avoiding any side effects,
this patch doesn't touch it.)
All the scaling of the KXSD9 involves multiplication with a
fraction number < 1.
However the scaling value returned from IIO_INFO_SCALE was
unpredictable as only the micros of the value was assigned, and
not the integer part, resulting in scaling like this:
Any readings from the raw interface of the KXSD9 driver will
return an empty string, because it does not return
IIO_VAL_INT but rather some random value from the accelerometer
to the caller.
On arm/arm64, we depend on the kvm_unmap_hva* callbacks (via
mmu_notifiers::invalidate_*) to unmap the stage2 pagetables when
the userspace buffer gets unmapped. However, when the Hypervisor
process exits without explicit unmap of the guest buffers, the only
notifier we get is kvm_arch_flush_shadow_all() (via mmu_notifier::release
) which does nothing on arm. Later this causes us to access pages that
were already released [via exit_mmap() -> unmap_vmas()] when we actually
get to unmap the stage2 pagetable [via kvm_arch_destroy_vm() ->
kvm_free_stage2_pgd()]. This triggers crashes with CONFIG_DEBUG_PAGEALLOC,
which unmaps any free'd pages from the linear map.
Łukasz Daniluk reported that on a RHEL kernel that his machine would lock up
after enabling function tracer. I asked him to bisect the functions within
available_filter_functions, which he did and it came down to three:
_paravirt_nop(), _paravirt_ident_32() and _paravirt_ident_64()
It was found that this is only an issue when noreplace-paravirt is added
to the kernel command line.
This means that those functions are most likely called within critical
sections of the funtion tracer, and must not be traced.
In newer kenels _paravirt_nop() is defined within gcc asm(), and is no
longer an issue. But both _paravirt_ident_{32,64}() causes the
following splat when they are traced:
v4.8-rc3 commit 99f3c90d0d ("dm flakey: error READ bios during the
down_interval") overlooked the 'drop_writes' feature, which is meant to
allow reads to be issued rather than errored, during the down_interval.
Fixes: 99f3c90d0d ("dm flakey: error READ bios during the down_interval") Reported-by: Qu Wenruo <quwenruo@cn.fujitsu.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
In commit c60ac5693c47 ("powerpc: Update kernel VSID range", 2013-03-13)
we lost a check on the region number (the top four bits of the effective
address) for addresses below PAGE_OFFSET. That commit replaced a check
that the top 18 bits were all zero with a check that bits 46 - 59 were
zero (performed for all addresses, not just user addresses).
This means that userspace can access an address like 0x1000_0xxx_xxxx_xxxx
and we will insert a valid SLB entry for it. The VSID used will be the
same as if the top 4 bits were 0, but the page size will be some random
value obtained by indexing beyond the end of the mm_ctx_high_slices_psize
array in the paca. If that page size is the same as would be used for
region 0, then userspace just has an alias of the region 0 space. If the
page size is different, then no HPTE will be found for the access, and
the process will get a SIGSEGV (since hash_page_mm() will refuse to create
a HPTE for the bogus address).
The access beyond the end of the mm_ctx_high_slices_psize can be at most
5.5MB past the array, and so will be in RAM somewhere. Since the access
is a load performed in real mode, it won't fault or crash the kernel.
At most this bug could perhaps leak a little bit of information about
blocks of 32 bytes of memory located at offsets of i * 512kB past the
paca->mm_ctx_high_slices_psize array, for 1 <= i <= 11.
The bootloader (U-boot) sometimes uses this timer for various delays.
It uses it as a ongoing counter, and does comparisons on the current
counter value. The timer counter is never stopped.
In some cases when the user interacts with the bootloader, or lets
it idle for some time before loading Linux, the timer may expire,
and an interrupt will be pending. This results in an unexpected
interrupt when the timer interrupt is enabled by the kernel, at
which point the event_handler isn't set yet. This results in a NULL
pointer dereference exception, panic, and no way to reboot.
Clear any pending interrupts after we stop the timer in the probe
function to avoid this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently it's possible for broken (or malicious) userspace to flood a
kernel log indefinitely with messages a-la
Program dmidecode tried to access /dev/mem between f0000->100000
because range_is_allowed() is case of CONFIG_STRICT_DEVMEM being turned on
dumps this information each and every time devmem_is_allowed() fails.
Reportedly userspace that is able to trigger contignuous flow of these
messages exists.
It would be possible to rate limit this message, but that'd have a
questionable value; the administrator wouldn't get information about all
the failing accessess, so then the information would be both superfluous
and incomplete at the same time :)
Returning EPERM (which is what is actually happening) is enough indication
for userspace what has happened; no need to log this particular error as
some sort of special condition.
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1607081137020.24757@cbobk.fhfr.pm Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Some users observed that "least connection" distribution algorithm doesn't
handle well bursts of TCP connections from reconnecting clients after
a node or network failure.
This is because the algorithm counts active connection as worth 256
inactive ones where for TCP, "active" only means TCP connections in
ESTABLISHED state. In case of a connection burst, new connections are
handled before previous ones have finished the three way handshaking so
that all are still counted as "inactive", i.e. cheap ones. The become
"active" quickly but at that time, all of them are already assigned to one
real server (or few), resulting in highly unbalanced distribution.
Address this by counting the "pre-established" states as "active".
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Before commit 6d7b857d541e ("net: use lib/percpu_counter API for
fragmentation mem accounting"), setting high threshold to 0 prevented
fragment reassembly as first fragment would be always evicted before
second could be added to the queue. While inefficient, some users
apparently relied on it.
Since the commit mentioned above, a percpu counter is used for
reassembly memory accounting and high batch size avoids taking slow path
in most common scenarios. As a result, a whole full sized packet can be
reassembled without the percpu counter's main counter changing its
value so that even with high_thresh set to 0, fragmented packets can be
still reassembled and processed.
Add explicit checks preventing reassembly if high threshold is zero.
[mk] backport to 3.12
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Emrah Demir <ed@abdsec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
According to figure 39 in PEB3086 data sheet, version 1.4 this indication
replaces DR when layer 1 transition source state is F6.
This fixes mISDN layer 1 getting stuck in F6 state in TE mode on
Dialogic Diva 2.02 card (and possibly others) when NT deactivates it.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name> Acked-by: Karsten Keil <keil@b1-systems.de> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Oliver Neukum <oliver@neukum.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Add proper error path (for disabling runtime PM) when registering of
hwrng fails.
Fixes: b329669ea0b5 ("hwrng: exynos - Add support for Exynos random number generator") Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Currently, the userspace governor only updates frequency on GOV_LIMITS
if policy->cur falls outside policy->{min/max}. However, it is also
necessary to update current frequency on GOV_LIMITS to match the user
requested value if it can be achieved within the new policy->{max/min}.
This was previously the behaviour in the governor until commit d1922f0
("cpufreq: Simplify userspace governor") which incorrectly assumed that
policy->cur == user requested frequency via scaling_setspeed. This won't
be true if the user requested frequency falls outside policy->{min/max}.
Ex: a temporary thermal cap throttled the user requested frequency.
Fix this by storing the user requested frequency in a seperate variable.
The governor will then try to achieve this request on every GOV_LIMITS
change.
Fixes: d1922f02562f (cpufreq: Simplify userspace governor) Signed-off-by: Sai Gurrappadi <sgurrappadi@nvidia.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Commit 655ee63cf371 ("scsi constants: command, sense key + additional
sense string") added a "Completed" sense string with key 0xF to
snstext[], but failed to updated the upper bounds check of the sense key
in scsi_sense_key_string().
Fixes: 655ee63cf371 ("[SCSI] scsi constants: command, sense key + additional sense strings") Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz>
projects / thirdparty / kernel / stable.git / log
