These have roughly the same purpose as the SMRR, which we do not need
to implement in KVM. However, Linux accesses MSR_K8_TSEG_ADDR at
boot, which causes problems when running a Xen dom0 under KVM.
Just return 0, meaning that processor protection of SMRAM is not
in effect.
Reported-by: M A Young <m.a.young@durham.ac.uk> Acked-by: Borislav Petkov <bp@suse.de> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The in kernel snprintf() will conveniently return the actual length of
the printed string even if not given an output beffer at all so just do
that rather than relying on the user to pass in a suitable buffer,
ensuring that we don't need to worry if the buffer was truncated due to
the size of the buffer passed in.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If a read is attempted which is smaller than the line length then we may
underflow the subtraction we're doing with the unsigned size_t type so
move some of the calculation to be additions on the right hand side
instead in order to avoid this.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
In btrfs_evict_inode, we properly truncate the page cache for evicted
inodes but then we call btrfs_wait_ordered_range for every inode as well.
It's the right thing to do for regular files but results in incorrect
behavior for device inodes for block devices.
filemap_fdatawrite_range gets called with inode->i_mapping which gets
resolved to the block device inode before getting passed to
wbc_attach_fdatawrite_inode and ultimately to inode_to_bdi. What happens
next depends on whether there's an open file handle associated with the
inode. If there is, we write to the block device, which is unexpected
behavior. If there isn't, we through normally and inode->i_data is used.
We can also end up racing against open/close which can result in crashes
when i_mapping points to a block device inode that has been closed.
Since there can't be any page cache associated with special file inodes,
it's safe to skip the btrfs_wait_ordered_range call entirely and avoid
the problem.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=100911 Tested-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by: Jeff Mahoney <jeffm@suse.com> Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Actually, spi_master_put() after spi_alloc_master() must _not_ be followed
by kfree(). The memory is already freed with the call to spi_master_put()
through spi_master_class, which registers a release function. Calling both
spi_master_put() and kfree() results in often nasty (and delayed) crashes
elsewhere in the kernel, often in the networking stack.
Link to patch and concerns: https://lkml.org/lkml/2012/9/3/269
or
http://lkml.iu.edu/hypermail/linux/kernel/1209.0/00790.html
Alexey Klimov: This revert becomes valid after 94c69f765f1b4a658d96905ec59928e3e3e07e6a when spi-imx.c
has been fixed and there is no need to call kfree() so comment
for spi_alloc_master() should be fixed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
On Intel Baytrail, there is case when interrupt handler get called, no SPI
message is captured. The RX FIFO is indeed empty when RX timeout pending
interrupt (SSSR_TINT) happens.
Use the BIOS version where both HSUART and SPI are on the same IRQ. Both
drivers are using IRQF_SHARED when calling the request_irq function. When
running two separate and independent SPI and HSUART application that
generate data traffic on both components, user will see messages like
below on the console:
pxa2xx-spi pxa2xx-spi.0: bad message state in interrupt handler
This commit will fix this by first checking Receiver Time-out Interrupt,
if it is disabled, ignore the request and return without servicing.
Signed-off-by: Tan, Jui Nee <jui.nee.tan@intel.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The size here comes from the user via the ioctl, it is a number between
1-u32max so the addition here could overflow on 32 bit systems.
Fixes: f453ba046074 ('DRM: add mode setting support') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Daniel Stone <daniels@collabora.com> Signed-off-by: Dave Airlie <airlied@gmail.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
When a write fails and a bad-block-list is present, we can
update the bad-block-list instead of writing the data. If
this succeeds then it is OK clear the relevant bitmap-bit as
no further 'sync' of the block is needed.
However if writing the bad-block-list fails then we need to
treat the write as failed and particularly must not clear
the bitmap bit. Otherwise the device can be re-added (after
any hardware connection issues are resolved) and because the
relevant bit in the bitmap is clear, that block will not be
resynced. This leads to data corruption.
We already delay the final bio_endio() on the write until
the bad-block-list is written so that when the write
returns: either that data is safe, the bad-block record is
safe, or the fact that the device is faulty is safe.
However we *don't* delay the clearing of the bitmap, so the
bitmap bit can be recorded as cleared before we know if the
bad-block-list was written safely.
So: delay that until the write really is safe.
i.e. move the call to close_write() until just before
calling bio_endio(), and recheck the 'is array degraded'
status before making that call.
This bug goes back to v3.1 when bad-block-lists were
introduced, though it only affects arrays created with
mdadm-3.3 or later as only those have bad-block lists.
Backports will require at least
Commit: 55ce74d4bfe1 ("md/raid1: ensure device failure recorded before write request returns.")
as well. I'll send that to 'stable' separately.
Note that of the two tests of R1BIO_WriteError that this
patch adds, the first is certain to fail and the second is
certain to succeed. However doing it this way makes the
patch more obviously correct. I will tidy the code up in a
future merge window.
When a write to one of the legs of a RAID1 fails, the failure is
recorded in the metadata of the other leg(s) so that after a restart
the data on the failed drive wont be trusted even if that drive seems
to be working again (maybe a cable was unplugged).
Similarly when we record a bad-block in response to a write failure,
we must not let the write complete until the bad-block update is safe.
Currently there is no interlock between the write request completing
and the metadata update. So it is possible that the write will
complete, the app will confirm success in some way, and then the
machine will crash before the metadata update completes.
This is an extremely small hole for a racy to fit in, but it is
theoretically possible and so should be closed.
So:
- set MD_CHANGE_PENDING when requesting a metadata update for a
failed device, so we can know with certainty when it completes
- queue requests that experienced an error on a new queue which
is only processed after the metadata update completes
- call raid_end_bio_io() on bios in that queue when the time comes.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
When a write fails and a bad-block-list is present, we can
update the bad-block-list instead of writing the data. If
this succeeds then it is OK clear the relevant bitmap-bit as
no further 'sync' of the block is needed.
However if writing the bad-block-list fails then we need to
treat the write as failed and particularly must not clear
the bitmap bit. Otherwise the device can be re-added (after
any hardware connection issues are resolved) and because the
relevant bit in the bitmap is clear, that block will not be
resynced. This leads to data corruption.
We already delay the final bio_endio() on the write until
the bad-block-list is written so that when the write
returns: either that data is safe, the bad-block record is
safe, or the fact that the device is faulty is safe.
However we *don't* delay the clearing of the bitmap, so the
bitmap bit can be recorded as cleared before we know if the
bad-block-list was written safely.
So: delay that until the write really is safe.
i.e. move the call to close_write() until just before
calling bio_endio(), and recheck the 'is array degraded'
status before making that call.
This bug goes back to v3.1 when bad-block-lists were
introduced, though it only affects arrays created with
mdadm-3.3 or later as only those have bad-block lists.
Backports will require at least
Commit: 95af587e95aa ("md/raid10: ensure device failure recorded before write request returns.")
as well. I'll send that to 'stable' separately.
Note that of the two tests of R10BIO_WriteError that this
patch adds, the first is certain to fail and the second is
certain to succeed. However doing it this way makes the
patch more obviously correct. I will tidy the code up in a
future merge window.
When a write to one of the legs of a RAID10 fails, the failure is
recorded in the metadata of the other legs so that after a restart
the data on the failed drive wont be trusted even if that drive seems
to be working again (maybe a cable was unplugged).
Currently there is no interlock between the write request completing
and the metadata update. So it is possible that the write will
complete, the app will confirm success in some way, and then the
machine will crash before the metadata update completes.
This is an extremely small hole for a racy to fit in, but it is
theoretically possible and so should be closed.
So:
- set MD_CHANGE_PENDING when requesting a metadata update for a
failed device, so we can know with certainty when it completes
- queue requests that experienced an error on a new queue which
is only processed after the metadata update completes
- call raid_end_bio_io() on bios in that queue when the time comes.
Signed-off-by: NeilBrown <neilb@suse.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Currently we do not validate rtas.entry before calling enter_rtas(). This
leads to a kernel oops when user space calls rtas system call on a powernv
platform (see below). This patch adds code to validate rtas.entry before
making enter_rtas() call.
ib_send_cm_sidr_rep could sometimes erase the node from the sidr
(depending on errors in the process). Since ib_send_cm_sidr_rep is
called both from cm_sidr_req_handler and cm_destroy_id, cm_id_priv
could be either erased from the rb_tree twice or not erased at all.
Fixing that by making sure it's erased only once before freeing
cm_id_priv.
Fixes: a977049dacde ('[PATCH] IB: Add the kernel CM implementation') Signed-off-by: Doron Tsur <doront@mellanox.com> Signed-off-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The argument being that the WMB will allow the load of A->state on CPU0
to cross over and observe CPU1's store of A->state, which will then
result in a double-drop and use-after-free.
Now the comment states (and this was true once upon a long time ago)
that we need to observe A->state while holding rq->lock because that
will order us against the wakeup; however the wakeup will not in fact
acquire (that) rq->lock; it takes A->pi_lock these days.
We can obviously fix this by upgrading the WMB to an MB, but that is
expensive, so we'd rather avoid that.
The alternative this patch takes is: smp_store_release(&A->on_cpu, 0),
which avoids the MB on some archs, but not important ones like ARM.
Reported-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Cc: manfred@colorfullife.com Cc: will.deacon@arm.com Fixes: e4a52bcb9a18 ("sched: Remove rq->lock from the first half of ttwu()") Link: http://lkml.kernel.org/r/20150929124509.GG3816@twins.programming.kicks-ass.net Signed-off-by: Ingo Molnar <mingo@kernel.org>
[lizf: Backported to 3.4: use smb_mb() instead of smp_store_release(), which
is not defined in 3.4.y] Signed-off-by: Zefan Li <lizefan@huawei.com>
The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
[lizf: Backported to 3.4: adjust filename] Signed-off-by: Zefan Li <lizefan@huawei.com>
Calling e.g. blk_queue_max_hw_sectors() after calls to
disk_stack_limits() discards the settings determined by
disk_stack_limits().
So we need to make those calls first.
Fixes: 199dc6ed5179 ("md/raid0: update queue parameter in a safer location.") Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32
zone, as is the case for some 32-bit kernels, then massage_gfp_flags()
will cause DMA memory allocated for devices with a 32..63-bit
coherent_dma_mask to fall back to using __GFP_DMA, even though there may
only be 32-bits of physical address available anyway.
Correct that case to compare against a mask the size of phys_addr_t
instead of always using a 64-bit mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com> Fixes: a2e715a86c6d ("MIPS: DMA: Fix computation of DMA flags from device's coherent_dma_mask.") Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9610/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The previous fix of pxa library support, which was introduced to fix the
library dependency, broke the previous SoC behavior, where a machine
code binding pxa2xx-ac97 with a coded relied on :
- sound/soc/pxa/pxa2xx-ac97.c
- sound/soc/codecs/XXX.c
For example, the mioa701_wm9713.c machine code is currently broken. The
"select ARM" statement wrongly selects the soc/arm/pxa2xx-ac97 for
compilation, as per an unfortunate fate SND_PXA2XX_AC97 is both declared
in sound/arm/Kconfig and sound/soc/pxa/Kconfig.
Fix this by ensuring that SND_PXA2XX_SOC correctly triggers the correct
pxa2xx-ac97 compilation.
Fixes: 846172dfe33c ("ASoC: fix SND_PXA2XX_LIB Kconfig warning") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
The IPv6 IPsec pre-encap path performs fragmentation for tunnel-mode
packets. That is, we perform fragmentation pre-encap rather than
post-encap.
A check was added later to ensure that proper MTU information is
passed back for locally generated traffic. Unfortunately this
check was performed on all IPsec packets, including transport-mode
packets.
What's more, the check failed to take GSO into account.
The end result is that transport-mode GSO packets get dropped at
the check.
This patch fixes it by moving the tunnel mode check forward as well
as adding the GSO check.
Fixes: dd767856a36e ("xfrm6: Don't call icmpv6_send on local error") Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
[lizf: Backported to 3.4:
- adjust context
- s/ignore_df/local_df] Signed-off-by: Zefan Li <lizefan@huawei.com>
Laura Abbott <labbott@redhat.com> produced a patch which lead us to
inspect symbol_put_addr(). This function has a comment claiming it
doesn't need to disable preemption around the module lookup
because it holds a reference to the module it wants to find, which
therefore cannot go away.
This is wrong (and a false optimization too, preempt_disable() is really
rather cheap, and I doubt any of this is on uber critical paths,
otherwise it would've retained a pointer to the actual module anyway and
avoided the second lookup).
While its true that the module cannot go away while we hold a reference
on it, the data structure we do the lookup in very much _CAN_ change
while we do the lookup. Therefore fix the comment and add the
required preempt_disable().
Reported-by: poma <pomidorabelisima@gmail.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Fixes: a6e6abd575fc ("module: remove module_text_address()") Signed-off-by: Zefan Li <lizefan@huawei.com>
In 2007, commit 07190a08eef36 ("Mark TSC on GeodeLX reliable")
bypassed verification of the TSC on Geode LX. However, this code
(now in the check_system_tsc_reliable() function in
arch/x86/kernel/tsc.c) was only present if CONFIG_MGEODE_LX was
set.
OpenWRT has recently started building its generic Geode target
for Geode GX, not LX, to include support for additional
platforms. This broke the timekeeping on LX-based devices,
because the TSC wasn't marked as reliable:
https://dev.openwrt.org/ticket/20531
By adding a runtime check on is_geode_lx(), we can also include
the fix if CONFIG_MGEODEGX1 or CONFIG_X86_GENERIC are set, thus
fixing the problem.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> Cc: Andres Salomon <dilinger@queued.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Marcelo Tosatti <marcelo@kvack.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1442409003.131189.87.camel@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
When a kernel is built covering ARMv6 to ARMv7, we omit to clear the
IT state when entering a signal handler. This can cause the first
few instructions to be conditionally executed depending on the parent
context.
In any case, the original test for >= ARMv7 is broken - ARMv6 can have
Thumb-2 support as well, and an ARMv6T2 specific build would omit this
code too.
Relax the test back to ARMv6 or greater. This results in us always
clearing the IT state bits in the PSR, even on CPUs where these bits
are reserved. However, they're reserved for the IT state, so this
should cause no harm.
Fixes: d71e1352e240 ("Clear the IT state when invoking a Thumb-2 signal handler") Acked-by: Tony Lindgren <tony@atomide.com> Tested-by: H. Nikolaus Schaller <hns@goldelico.com> Tested-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
The ARM architecture reference specifies that the IT state bits in the
PSR must be all zeros in ARM mode or behavior is unspecified. On the
Qualcomm Snapdragon S4/Krait architecture CPUs the processor continues
to consider the IT state bits while in ARM mode. This makes it so
that some instructions are skipped by the CPU.
Signed-off-by: T.J. Purtell <tj@mobisocial.us>
[rmk+kernel@arm.linux.org.uk: fixed whitespace formatting in patch] Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
The original patch introducing this header wrote the number of CPUs available
and online in one order and then swapped those values when reading, fix it.
Acked-by: Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Ahern <dsahern@gmail.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kan Liang <kan.liang@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Wang Nan <wangnan0@huawei.com> Fixes: fbe96f29ce4b ("perf tools: Make perf.data more self-descriptive (v8)") Link: http://lkml.kernel.org/r/20150911153323.GP23511@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[lizf: Backported to 3.4: fix it by saving values in an array and then print
it in reverse order] Signed-off-by: Zefan Li <lizefan@huawei.com>
This fixes a race which can result in the same virtual IRQ number
being assigned to two different MSI interrupts. The most visible
consequence of that is usually a warning and stack trace from the
sysfs code about an attempt to create a duplicate entry in sysfs.
The race happens when one CPU (say CPU 0) is disposing of an MSI
while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls
(for example) pnv_teardown_msi_irqs(), which calls
msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its
hardware IRQ number) is no longer in use. Then, before CPU 0 gets
to calling irq_dispose_mapping() to free up the virtal IRQ number,
CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an
MSI, and gets the same hardware IRQ number that CPU 0 just freed.
CPU 1 then calls irq_create_mapping() to get a virtual IRQ number,
which sees that there is currently a mapping for that hardware IRQ
number and returns the corresponding virtual IRQ number (which is
the same virtual IRQ number that CPU 0 was using). CPU 0 then
calls irq_dispose_mapping() and frees that virtual IRQ number.
Now, if another CPU comes along and calls irq_create_mapping(), it
is likely to get the virtual IRQ number that was just freed,
resulting in the same virtual IRQ number apparently being used for
two different hardware interrupts.
To fix this race, we just move the call to msi_bitmap_free_hwirqs()
to after the call to irq_dispose_mapping(). Since virq_to_hw()
doesn't work for the virtual IRQ number after irq_dispose_mapping()
has been called, we need to call it before irq_dispose_mapping() and
remember the result for the msi_bitmap_free_hwirqs() call.
The pattern of calling msi_bitmap_free_hwirqs() before
irq_dispose_mapping() appears in 5 places under arch/powerpc, and
appears to have originated in commit 05af7bd2d75e ("[POWERPC] MPIC
U3/U4 MSI backend") from 2007.
Fixes: 05af7bd2d75e ("[POWERPC] MPIC U3/U4 MSI backend") Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.2:
- powernv uses a private functions instead of msi_bitmap_free_hwirqs()
- Adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
While working on the 32-bit ARM port of UEFI, I noticed a strange
corruption in the kernel log. The following snprintf() statement
(in drivers/firmware/efi/efi.c:efi_md_typeattr_format())
As it turns out, this is caused by incorrect code being emitted for
the string() function in lib/vsprintf.c. The following code
if (!(spec.flags & LEFT)) {
while (len < spec.field_width--) {
if (buf < end)
*buf = ' ';
++buf;
}
}
for (i = 0; i < len; ++i) {
if (buf < end)
*buf = *s;
++buf; ++s;
}
while (len < spec.field_width--) {
if (buf < end)
*buf = ' ';
++buf;
}
when called with len == 0, triggers an issue in the GCC SRA optimization
pass (Scalar Replacement of Aggregates), which handles promotion of signed
struct members incorrectly. This is a known but as yet unresolved issue.
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=65932). In this particular
case, it is causing the second while loop to be executed erroneously a
single time, causing the additional space characters to be printed.
So disable the optimization by passing -fno-ipa-sra.
Acked-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
It looks like the Kconfig check that was meant to fix this (commit fe9233fb6914a0eb20166c967e3020f7f0fba2c9 [SCSI] scsi_dh: fix kconfig related
build errors) was actually reversed, but no-one noticed until the new set of
patches which separated DM and SCSI_DH).
Fixes: fe9233fb6914a0eb20166c967e3020f7f0fba2c9 Signed-off-by: Christoph Hellwig <hch@lst.de> Tested-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Fix B-tree corruption when a new record is inserted at position 0 in the
node in hfs_brec_insert().
This is an identical change to the corresponding hfs b-tree code to Sergei
Antonov's "hfsplus: fix B-tree corruption after insertion at position 0",
to keep similar code paths in the hfs and hfsplus drivers in sync, where
appropriate.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Cc: Sergei Antonov <saproj@gmail.com> Cc: Joe Perches <joe@perches.com> Reviewed-by: Vyacheslav Dubeyko <slava@dubeyko.com> Cc: Anton Altaparmakov <anton@tuxera.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Pages looked up by __hfs_bnode_create() (called by hfs_bnode_create() and
hfs_bnode_find() for finding or creating pages corresponding to an inode)
are immediately kmap()'ed and used (both read and write) and kunmap()'ed,
and should not be page_cache_release()'ed until hfs_bnode_free().
This patch fixes a problem I first saw in July 2012: merely running "du"
on a large hfsplus-mounted directory a few times on a reasonably loaded
system would get the hfsplus driver all confused and complaining about
B-tree inconsistencies, and generates a "BUG: Bad page state". Most
recently, I can generate this problem on up-to-date Fedora 22 with shipped
kernel 4.0.5, by running "du /" (="/" + "/home" + "/mnt" + other smaller
mounts) and "du /mnt" simultaneously on two windows, where /mnt is a
lightly-used QEMU VM image of the full Mac OS X 10.9:
After applying the patch, I was able to run "du /" (60+ times) and "du
/mnt" (150+ times) continuously and simultaneously for 6+ hours.
There are many reports of the hfsplus driver getting confused under load
and generating "BUG: Bad page state" or other similar issues over the
years. [1]
The unpatched code [2] has always been wrong since it entered the kernel
tree. The only reason why it gets away with it is that the
kmap/memcpy/kunmap follow very quickly after the page_cache_release() so
the kernel has not had a chance to reuse the memory for something else,
most of the time.
The current RW driver appears to have followed the design and development
of the earlier read-only hfsplus driver [3], where-by version 0.1 (Dec
2001) had a B-tree node-centric approach to
read_cache_page()/page_cache_release() per bnode_get()/bnode_put(),
migrating towards version 0.2 (June 2002) of caching and releasing pages
per inode extents. When the current RW code first entered the kernel [2]
in 2005, there was an REF_PAGES conditional (and "//" commented out code)
to switch between B-node centric paging to inode-centric paging. There
was a mistake with the direction of one of the REF_PAGES conditionals in
__hfs_bnode_create(). In a subsequent "remove debug code" commit [4], the
read_cache_page()/page_cache_release() per bnode_get()/bnode_put() were
removed, but a page_cache_release() was mistakenly left in (propagating
the "REF_PAGES <-> !REF_PAGE" mistake), and the commented-out
page_cache_release() in bnode_release() (which should be spanned by
!REF_PAGES) was never enabled.
References:
[1]:
Michael Fox, Apr 2013
http://www.spinics.net/lists/linux-fsdevel/msg63807.html
("hfsplus volume suddenly inaccessable after 'hfs: recoff %d too large'")
Sasha Levin, Feb 2015
http://lkml.org/lkml/2015/2/20/85 ("use after free")
Many file systems that implement the show_options hook fail to correctly
escape their output which could lead to unescaped characters (e.g. new
lines) leaking into /proc/mounts and /proc/[pid]/mountinfo files. This
could lead to confusion, spoofed entries (resulting in things like
systemd issuing false d-bus "mount" notifications), and who knows what
else. This looks like it would only be the root user stepping on
themselves, but it's possible weird things could happen in containers or
in other situations with delegated mount privileges.
Here's an example using overlay with setuid fusermount trusting the
contents of /proc/mounts (via the /etc/mtab symlink). Imagine the use
of "sudo" is something more sneaky:
This fixes the problem by adding new seq_show_option and
seq_show_option_n helpers, and updating the vulnerable show_option
handlers to use them as needed. Some, like SELinux, need to be open
coded due to unusual existing escape mechanisms.
[akpm@linux-foundation.org: add lost chunk, per Kees]
[keescook@chromium.org: seq_show_option should be using const parameters] Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Acked-by: Jan Kara <jack@suse.com> Acked-by: Paul Moore <paul@paul-moore.com> Cc: J. R. Okajima <hooanon05g@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4:
- adjust context
- one more place in ceph needs to be changed
- drop changes to overlayfs
- drop showing vers in cifs] Signed-off-by: Zefan Li <lizefan@huawei.com>
Currently context size (cra_ctxsize) doesn't specified for
ghash_async_alg. Which means it's zero. Thus crypto_create_tfm()
doesn't allocate needed space for ghash_async_ctx, so any
read/write to ctx (e.g. in ghash_async_init_tfm()) is not valid.
Signed-off-by: Andrey Ryabinin <aryabinin@odin.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Zefan Li <lizefan@huawei.com>
We have many WR opcodes that are only supported in kernel space
and/or require optional information to be copied into the WR
structure. Reject all those not explicitly handled so that we
can't pass invalid information to drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Reviewed-by: Sagi Grimberg <sagig@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
With the radeon driver loaded the HP Compaq dc5750
Small Form Factor machine fails to resume from suspend.
Adding a quirk similar to other devices avoids
the problem and the system resumes properly.
Signed-off-by: Jeffery Miller <jmiller@neverware.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Fixes: 2a72f212263701b927559f6850446421d5906c41 ("IB/uverbs: Remove dev_table")
Before this commit there was a device look-up table that was protected
by a spin_lock used by ib_uverbs_open and by ib_uverbs_remove_one. When
it was dropped and container_of was used instead, it enabled the race
with remove_one as dev might be freed just after:
dev = container_of(inode->i_cdev, struct ib_uverbs_device, cdev) but
before the kref_get.
In addition, this buggy patch added some dead code as
container_of(x,y,z) can never be NULL and so dev can never be NULL.
As a result the comment above ib_uverbs_open saying "the open method
will either immediately run -ENXIO" is wrong as it can never happen.
The solution follows Jason Gunthorpe suggestion from below URL:
https://www.mail-archive.com/linux-rdma@vger.kernel.org/msg25692.html
cdev will hold a kref on the parent (the containing structure,
ib_uverbs_device) and only when that kref is released it is
guaranteed that open will never be called again.
In addition, fixes the active count scheme to use an atomic
not a kref to prevent WARN_ON as pointed by above comment
from Jason.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Shachar Raindel <raindel@mellanox.com> Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The unregister path of platform_device is broken. On registration, it
will register all resources with either a parent already set, or
type==IORESOURCE_{IO,MEM}. However, on unregister it will release
everything with type==IORESOURCE_{IO,MEM}, but ignore the others. There
are also cases where resources don't get registered in the first place,
like with devices created by of_platform_populate()*.
Fix the unregister path to be symmetrical with the register path by
checking the parent pointer instead of the type field to decide which
resources to unregister. This is safe because the upshot of the
registration path algorithm is that registered resources have a parent
pointer, and non-registered resources do not.
* It can be argued that of_platform_populate() should be registering
it's resources, and they argument has some merit. However, there are
quite a few platforms that end up broken if we try to do that due to
overlapping resources in the device tree. Until that is fixed, we need
to solve the immediate problem.
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Rob Herring <robh@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: Grant Likely <grant.likely@linaro.org> Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
If the internal call to of_address_to_resource() fails, we end up
looping forever in of_find_matching_node_by_address(). This can be
caused by a defective device tree, or calling with an incorrect
matches argument.
Fix by calling of_find_matching_node() unconditionally at the end of
the loop.
Signed-off-by: David Daney <david.daney@cavium.com> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Most of the time this isn't an issue since hotplugging an adaptor will
trigger a crtc mode change which in turn, causes the driver to probe
every DisplayPort for a dpcd. However, in cases where hotplugging
doesn't cause a mode change (specifically when one unplugs a monitor
from a DisplayPort connector, then plugs that same monitor back in
seconds later on the same port without any other monitors connected), we
never probe for the dpcd before starting the initial link training. What
happens from there looks like this:
- GPU has only one monitor connected. It's connected via
DisplayPort, and does not go through an adaptor of any sort.
- User unplugs DisplayPort connector from GPU.
- Change in HPD is detected by the driver, we probe every
DisplayPort for a possible connection.
- Probe the port the user originally had the monitor connected
on for it's dpcd. This fails, and we clear the first (and only
the first) byte of the dpcd to indicate we no longer have a
dpcd for this port.
- User plugs the previously disconnected monitor back into the
same DisplayPort.
- radeon_connector_hotplug() is called before everyone else,
and tries to handle the link training. Since only the first
byte of the dpcd is zeroed, the driver is able to complete
link training but does so against the wrong dpcd, causing it
to initialize the link with the wrong settings.
- Display stays blank (usually), dpcd is probed after the
initial link training, and the driver prints no obvious
messages to the log.
In theory, since only one byte of the dpcd is chopped off (specifically,
the byte that contains the revision information for DisplayPort), it's
not entirely impossible that this bug may not show on certain monitors.
For instance, the only reason this bug was visible on my ASUS PB238
monitor was due to the fact that this monitor using the enhanced framing
symbol sequence, the flag for which is ignored if the radeon driver
thinks that the DisplayPort version is below 1.1.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Consider eCryptfs dcache entries to be stale when the corresponding
lower inode's i_nlink count is zero. This solves a problem caused by the
lower inode being directly modified, without going through the eCryptfs
mount, leaving stale eCryptfs dentries cached and the eCryptfs inode's
i_nlink count not being cleared.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com> Reported-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.2:
- Test d_revalidate pointer directly rather than a DCACHE_OP flag
- Open-code d_inode()
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
NFSv4 takes O_EXCL as a sign that a setattr command should be sent,
probably to reset the timestamps.
When it was an O_RDONLY open, the SETATTR command does not
identify any actual attributes to change.
If no delegation was provided to the open, the SETATTR uses the
all-zeros stateid and the request is accepted (at least by the
Linux NFS server - no harm, no foul).
If a read-delegation was provided, this is used in the SETATTR
request, and a Netapp filer will justifiably claim
NFS4ERR_BAD_STATEID, which the Linux client takes as a sign
to retry - indefinitely.
So only treat O_EXCL specially if O_CREAT was also given.
Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
wf_unregister_client() increments the client count when a client
unregisters. That is obviously incorrect. Decrement that client count
instead.
Fixes: 75722d3992f5 ("[PATCH] ppc64: Thermal control for SMU based machines") Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Zefan Li <lizefan@huawei.com>
parport_find_base() will implicitly do parport_get_port() which
increases the refcount. Then parport_register_device() will again
increment the refcount. But while unloading the module we are only
doing parport_unregister_device() decrementing the refcount only once.
We add an parport_put_port() to neutralize the effect of
parport_get_port().
When a (e.g.) RAID5 array is reshaped to RAID0, the updating
of queue parameters (e.g. max number of sectors per bio) is
done in the wrong place.
It should be part of ->run, but it is actually part of ->takeover.
This means it happens before level_store() calls:
blk_set_stacking_limits(&mddev->queue->limits);
and so it ineffective. This can lead to errors from underlying
devices.
So move all the relevant settings out of create_stripe_zones()
and into raid0_run().
As this can lead to a bug-on it is suitable for any -stable
kernel which supports reshape to RAID0. So 2.6.35 or later.
As the bug has been present for five years there is no urgency,
so no need to rush into -stable.
Fixes: 9af204cf720c ("md: Add support for Raid5->Raid0 and Raid10->Raid0 takeover") Reported-by: Yi Zhang <yizhan@redhat.com> Signed-off-by: NeilBrown <neilb@suse.com>
[lizf: Backported to 3.4:
- adjust context
- remove changes to discard and write-same features] Signed-off-by: Zefan Li <lizefan@huawei.com>
The Linux NFS server returns garbage in the data payload of inline
NFS/RDMA READ replies. These are READs of under 1000 bytes or so
where the client has not provided either a reply chunk or a write
list.
The NFS server delivers the data payload for an NFS READ reply to
the transport in an xdr_buf page list. If the NFS client did not
provide a reply chunk or a write list, send_reply() is supposed to
set up a separate sge for the page containing the READ data, and
another sge for XDR padding if needed, then post all of the sges via
a single SEND Work Request.
The problem is send_reply() does not advance through the xdr_buf
when setting up scatter/gather entries for SEND WR. It always calls
dma_map_xdr with xdr_off set to zero. When there's more than one
sge, dma_map_xdr() sets up the SEND sge's so they all point to the
xdr_buf's head.
The current Linux NFS/RDMA client always provides a reply chunk or
a write list when performing an NFS READ over RDMA. Therefore, it
does not exercise this particular case. The Linux server has never
had to use more than one extra sge for building RPC/RDMA replies
with a Linux client.
However, an NFS/RDMA client _is_ allowed to send small NFS READs
without setting up a write list or reply chunk. The NFS READ reply
fits entirely within the inline reply buffer in this case. This is
perhaps a more efficient way of performing NFS READs that the Linux
NFS/RDMA client may some day adopt.
Fixes: b432e6b3d9c1 ('svcrdma: Change DMA mapping logic to . . .') BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=285 Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The EPOW interrupt handler uses rtas_get_sensor(), which in turn
uses rtas_busy_delay() to wait for RTAS becoming ready in case it
is necessary. But rtas_busy_delay() is annotated with might_sleep()
and thus may not be used by interrupts handlers like the EPOW handler!
This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is
enabled:
Fix this issue by introducing a new rtas_get_sensor_fast() function
that does not use rtas_busy_delay() - and thus can only be used for
sensors that do not cause a BUSY condition - known as "fast" sensors.
The EPOW sensor is defined to be "fast" in sPAPR - mpe.
Fixes: 587f83e8dd50 ("powerpc/pseries: Use rtas_get_sensor in RAS code") Signed-off-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Zefan Li <lizefan@huawei.com>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog] Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
[bwh: Backported to 3.2:
- Put the class check in the new function as there is no
DECLARE_PCI_FIXUP_CLASS_EARLY(
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions. This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions. Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.
On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang. This has to do with how the kernel tracks the expected value of the
F bit per function.
Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.
When hangs occur, typically the error message:
vpd r/w failed. This is likely a firmware bug on this device.
will be seen.
Never set this bit on function 0 or there will be an infinite recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
We already set a station to be associated when peering completes, both
in user space and in the kernel. Thus we should always have an
associated sta before sending data frames to that station.
Failure to check assoc state can cause crashes in the lower-level driver
due to transmitting unicast data frames before driver sta structures
(e.g. ampdu state in ath9k) are initialized. This occurred when
forwarding in the presence of fixed mesh paths: frames were transmitted
to stations with whom we hadn't yet completed peering.
Reported-by: Alexis Green <agreen@cococorp.com> Tested-by: Jesse Jones <jjones@cococorp.com> Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.
Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.
Fixes: 63c4408074cb ("PCI: Add quirk for setting valid class for TI816X Endpoint") Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Hemant Pedanekar <hemantp@ti.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The input_dev is already gone when the rc device is being unregistered
so checking for its presence only means that no remove uevent will be
generated.
Signed-off-by: David Härdeman <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
As reported at https://bugs.launchpad.net/qemu/+bug/1494350,
it is possible to have vcpu->arch.st.last_steal initialized
from a thread other than vcpu thread, say the iothread, via
KVM_SET_MSRS.
Which can cause an overflow later (when subtracting from vcpu threads
sched_info.run_delay).
To avoid that, move steal time accumulation to vcpu entry time,
before copying steal time data to guest.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Reviewed-by: David Matlack <dmatlack@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit 4c7e309340ff ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().
The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them. If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.
Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.
Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.c
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda6187181 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.
The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:
1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.
2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).
The following simplified method is used instead:
All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.
This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.
Fixes: aebda6187181 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE") Reported-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@kernel.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
AudioQuest DragonFly DAC reports a volume control range of 0..50
(0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which
is obviously incorrect and would cause software using the dB information
in e.g. volume sliders to have a massive volume difference in 100..102%
range.
Commit 2d1cb7f658fb ("ALSA: usb-audio: add dB range mapping for some
devices") added a dB range mapping for it with range 0..50 dB.
However, the actual volume mapping seems to be neither linear volume nor
linear dB scale, but instead quite close to the cubic mapping e.g.
alsamixer uses, with a range of approx. -53...0 dB.
Replace the previous quirk with a custom dB mapping based on some basic
output measurements, using a 10-item range TLV (which will still fit in
alsa-lib MAX_TLV_RANGE_SIZE).
Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the
range is 0..50, so if this gets fixed/changed in later HW revisions it
will no longer be applied.
v2: incorporated Takashi Iwai's suggestion for the quirk application
method
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by: Takashi Iwai <tiwai@suse.de>
[lizf: Backoported to 3.4: use dev_info() instead of usb_audio_info()] Signed-off-by: Zefan Li <lizefan@huawei.com>
Add helper macros with a little bit of preprocessor magic to
automatically compute the length of a TLV item. This lets us avoid
having to compute this by hand, and will allow to use items that do
not use a fixed length.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Zefan Li <lizefan@huawei.com>
This was meant to print base address and entry count; make it do so
again.
Fixes: 37868fe113ff "x86/ldt: Make modify_ldt synchronous" Signed-off-by: Jan Beulich <jbeulich@suse.com> Acked-by: Andy Lutomirski <luto@kernel.org> Link: http://lkml.kernel.org/r/56797D8402000078000C24F0@prv-mh.provo.novell.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The unix_dgram_sendmsg routine use the following test
if (unlikely(unix_peer(other) != sk && unix_recvq_full(other))) {
to determine if sk and other are in an n:1 association (either
established via connect or by using sendto to send messages to an
unrelated socket identified by address). This isn't correct as the
specified address could have been bound to the sending socket itself or
because this socket could have been connected to itself by the time of
the unix_peer_get but disconnected before the unix_state_lock(other). In
both cases, the if-block would be entered despite other == sk which
might either block the sender unintentionally or lead to trying to unlock
the same spin lock twice for a non-blocking send. Add a other != sk
check to guard against this.
Fixes: 7d267278a9ec ("unix: avoid use-after-free in ep_remove_wait_queue") Reported-By: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Tested-by: Philipp Hahn <pmhahn@pmhahn.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Docbook does not like the definition of macros inside a field declaration
and adds a warning. Move the definition out.
Fixes: 79462ad02e86180 ("net: add validation for the socket syscall protocol argument") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
I ran into a scenario where while one cpu was stuck and should have
panic'd because of the NMI watchdog, it didn't. The reason was another
cpu was spewing stack dumps on to the console. Upon investigation, I
noticed that when writing to the console and also when dumping the
stack, the watchdog is touched.
This causes all the cpus to reset their NMI watchdog flags and the
'stuck' cpu just spins forever.
This change causes the semantics of touch_nmi_watchdog to be changed
slightly. Previously, I accidentally changed the semantics and we
noticed there was a codepath in which touch_nmi_watchdog could be
touched from a preemtible area. That caused a BUG() to happen when
CONFIG_DEBUG_PREEMPT was enabled. I believe it was the acpi code.
My attempt here re-introduces the change to have the
touch_nmi_watchdog() code only touch the local cpu instead of all of the
cpus. But instead of using __get_cpu_var(), I use the
__raw_get_cpu_var() version.
This avoids the preemption problem. However my reasoning wasn't because
I was trying to be lazy. Instead I rationalized it as, well if
preemption is enabled then interrupts should be enabled to and the NMI
watchdog will have no reason to trigger. So it won't matter if the
wrong cpu is touched because the percpu interrupt counters the NMI
watchdog uses should still be incrementing.
Don said:
: I'm ok with this patch, though it does alter the behaviour of how
: touch_nmi_watchdog works. For the most part I don't think most callers
: need to touch all of the watchdogs (on each cpu). Perhaps a corner case
: will pop up (the scheduler?? to mimic touch_all_softlockup_watchdogs() ).
:
: But this does address an issue where if a system is locked up and one cpu
: is spewing out useful debug messages (or error messages), the hard lockup
: will fail to go off. We have seen this on RHEL also.
Signed-off-by: Don Zickus <dzickus@redhat.com> Signed-off-by: Ben Zhang <benzh@chromium.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
On a high-traffic router with many processors and many IPv6 dst
entries, soft lockup in fib6_run_gc() can occur when number of
entries reaches gc_thresh.
This happens because fib6_run_gc() uses fib6_gc_lock to allow
only one thread to run the garbage collector but ip6_dst_gc()
doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc()
returns. On a system with many entries, this can take some time
so that in the meantime, other threads pass the tests in
ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for
the lock. They then have to run the garbage collector one after
another which blocks them for quite long.
Resolve this by replacing special value ~0UL of expire parameter
to fib6_run_gc() by explicit "force" parameter to choose between
spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with
force=false if gc_thresh is reached but not max_size.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
If the sending queue has a task without ->rq_cong set at the front,
and then a number of tasks with ->rq_cong set such that they use
the entire congestion window, then the queue deadlocks. The first
entry cannot be processed until later entries complete.
This scenario has been seen with a client using UDP to access a server,
and the network connection breaking for a period of time - it doesn't
recover.
It never really makes sense for an ->rq_cong request to be on the ->sending
queue, but it can happen when a request is being retried, and finds
the transport if locked (XPRT_LOCKED). In this case we simple call
__xprt_put_cong() and the deadlock goes away.
net->ct.nf_conntrack_cachep is created with SLAB_DESTROY_BY_RCU.
The hash is protected by rcu, so readers look up conntracks without
locks.
A conntrack is removed from the hash, but in this moment a few readers
still can use the conntrack. Then this conntrack is released and another
thread creates conntrack with the same address and the equal tuple.
After this a reader starts to validate the conntrack:
* It's not dying, because a new conntrack was created
* nf_ct_tuple_equal() returns true.
But this conntrack is not initialized yet, so it can not be used by two
threads concurrently. In this case BUG_ON may be triggered from
nf_nat_setup_info().
Florian Westphal suggested to check the confirm bit too. I think it's
right.
task 1 task 2 task 3
nf_conntrack_find_get
____nf_conntrack_find
destroy_conntrack
hlist_nulls_del_rcu
nf_conntrack_free
kmem_cache_free
__nf_conntrack_alloc
kmem_cache_alloc
memset(&ct->tuplehash[IP_CT_DIR_MAX],
if (nf_ct_is_dying(ct))
if (!nf_ct_tuple_equal()
I'm not sure, that I have ever seen this race condition in a real life.
Currently we are investigating a bug, which is reproduced on a few nodes.
In our case one conntrack is initialized from a few tasks concurrently,
we don't have any other explanation for this.
Routes need to be probed asynchronous otherwise the call stack gets
exhausted when the kernel attemps to deliver another skb inline, like
e.g. xt_TEE does, and we probe at the same time.
We update neigh->updated still at once, otherwise we would send to
many probes.
Cc: Julian Anastasov <ja@ssi.bg> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
I found if we write a larger than 4GB value to some sysctl
variables, the sending syscall will hang up forever, because these
variables are 32 bits, such large values make them overflow to 0 or
negative.
This patch try to fix overflow or prevent from zero value setup
of below sysctl variables:
net.core.wmem_default
net.core.rmem_default
net.core.rmem_max
net.core.wmem_max
net.ipv4.udp_rmem_min
net.ipv4.udp_wmem_min
net.ipv4.tcp_wmem
net.ipv4.tcp_rmem
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Li Yu <raise.sail@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
As reported by Dmitry Vyukov, we really shouldn't do ipc_addid() before
having initialized the IPC object state. Yes, we initialize the IPC
object in a locked state, but with all the lockless RCU lookup work,
that IPC object lock no longer means that the state cannot be seen.
We already did this for the IPC semaphore code (see commit e8577d1f0329:
"ipc/sem.c: fully initialize sem_array before making it visible") but we
clearly forgot about msg and shm.
This is needed to avoid the possibility that the guest triggers
an infinite stream of #DB exceptions (CVE-2015-8104).
VMX is not affected: because it does not save DR6 in the VMCS,
it already intercepts #DB unconditionally.
Reported-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[bwh: Backported to 3.2, with thanks to Paolo:
- update_db_bp_intercept() was called update_db_intercept()
- The remaining call is in svm_guest_debug() rather than through svm_x86_ops] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Zefan Li <lizefan@huawei.com>
It was found that a guest can DoS a host by triggering an infinite
stream of "alignment check" (#AC) exceptions. This causes the
microcode to enter an infinite loop where the core never receives
another interrupt. The host kernel panics pretty quickly due to the
effects (CVE-2015-5307).
Signed-off-by: Eric Northup <digitaleric@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
[lizf: Backported to 3.4:
- adjust filename
- adjust context
- add definition of AC_VECTOR] Signed-off-by: Zefan Li <lizefan@huawei.com>
Currently we don't check if the new MTU is valid or not and this allows
one to configure a smaller than minimum allowed by RFCs or even bigger
than interface own MTU, which is a problem as it may lead to packet
drops.
If you have a daemon like NetworkManager running, this may be exploited
by remote attackers by forging RA packets with an invalid MTU, possibly
leading to a DoS. (NetworkManager currently only validates for values
too small, but not for too big ones.)
The fix is just to make sure the new value is valid. That is, between
IPV6_MIN_MTU and interface's MTU.
Note that similar check is already performed at
ndisc_router_discovery(), for when kernel itself parses the RA.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
i=`keyctl add user a a @s`
keyctl request2 keyring foo bar @t
keyctl unlink $i @s
tries to invoke an upcall to instantiate a keyring if one doesn't already
exist by that name within the user's keyring set. However, if the upcall
fails, the code sets keyring->type_data.reject_error to -ENOKEY or some
other error code. When the key is garbage collected, the key destroy
function is called unconditionally and keyring_destroy() uses list_empty()
on keyring->type_data.link - which is in a union with reject_error.
Subsequently, the kernel tries to unlink the keyring from the keyring names
list - which oopses like this:
(1) key_gc_unused_keys() which frees key->security and then calls
keyring_destroy() to unlink the name from the name list
(2) find_keyring_by_name() which calls key_permission(), thus accessing
key->security, on a key before checking to see whether the key usage is 0
(ie. the key is dead and might be cleaned up).
Fix this by calling ->destroy() before cleaning up the core key data -
including key->security.
Reported-by: Petr Matousek <pmatouse@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com>
[lizf: Backported to 3.4: adjust indentation] Signed-off-by: Zefan Li <lizefan@huawei.com>
Fix potential null-pointer dereference at probe by making sure that the
required endpoints are present.
The whiteheat driver assumes there are at least five pairs of bulk
endpoints, of which the final pair is used for the "command port". An
attempt to bind to an interface with fewer bulk endpoints would
currently lead to an oops.
Fixes CVE-2015-5257.
Reported-by: Moein Ghasemzadeh <moein@istuary.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Zefan Li <lizefan@huawei.com>
Currently slhc_init() treats out-of-range values of rslots and tslots
as equivalent to 0, except that if tslots is too large it will
dereference a null pointer (CVE-2015-7799).
Add a range-check at the top of the function and make it return an
ERR_PTR() on error instead of NULL. Change the callers accordingly.
Compile-tested only.
Reported-by: 郭永刚 <guoyonggang@360.cn>
References: http://article.gmane.org/gmane.comp.security.oss.general/17908 Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
virtio declares support for NETIF_F_FRAGLIST, but assumes
that there are at most MAX_SKB_FRAGS + 2 fragments which isn't
always true with a fraglist.
A longer fraglist in the skb will make the call to skb_to_sgvec overflow
the sg array, leading to memory corruption.
Drop NETIF_F_FRAGLIST so we only get what we can handle.
Cc: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
unfortunately, allowing an arbitrary 16bit value means a possibility of
overflow in the calculation of total number of pages in bio_map_user_iov() -
we rely on there being no more than PAGE_SIZE members of sum in the
first loop there. If that sum wraps around, we end up allocating
too small array of pointers to pages and it's easy to overflow it in
the second loop.
X-Coverup: TINC (and there's no lumber cartel either) Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lizf: Backported to 3.4: s/MAX_UIOVEC/UIO_MAXIOV] Signed-off-by: Zefan Li <lizefan@huawei.com>
Sasha's found a NULL pointer dereference in the RDS connection code when
sending a message to an apparently unbound socket. The problem is caused
by the code checking if the socket is bound in rds_sendmsg(), which checks
the rs_bound_addr field without taking a lock on the socket. This opens a
race where rs_bound_addr is temporarily set but where the transport is not
in rds_bind(), leading to a NULL pointer dereference when trying to
dereference 'trans' in __rds_conn_create().
Vegard wrote a reproducer for this issue, so kindly ask him to share if
you're interested.
I cannot reproduce the NULL pointer dereference using Vegard's reproducer
with this patch, whereas I could without.
Complete earlier incomplete fix to CVE-2015-6937:
74e98eb08588 ("RDS: verify the underlying transport exists before creating a connection")
Cc: David S. Miller <davem@davemloft.net> Reviewed-by: Vegard Nossum <vegard.nossum@oracle.com> Reviewed-by: Sasha Levin <sasha.levin@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
AF_INET, AF_INET6 sockets actually only support 8-bit protocol
identifiers. inet_sock's skc_protocol field thus is sized accordingly,
thus larger protocol identifiers simply cut off the higher bits and
store a zero in the protocol fields.
This could lead to e.g. NULL function pointer because as a result of
the cut off inet_num is zero and we call down to inet_autobind, which
is NULL for raw sockets.
I found no particular commit which introduced this problem.
CVE: CVE-2015-8543 Cc: Cong Wang <cwang@twopensource.com> Reported-by: 郭永刚 <guoyonggang@360.cn> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: open-code U8_MAX] Signed-off-by: Zefan Li <lizefan@huawei.com>
Reported-by: Dmitry Vyukov <dvyukov@gmail.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Rainer Weikusat <rweikusat@mobileactivedefense.com> writes:
An AF_UNIX datagram socket being the client in an n:1 association with
some server socket is only allowed to send messages to the server if the
receive queue of this socket contains at most sk_max_ack_backlog
datagrams. This implies that prospective writers might be forced to go
to sleep despite none of the message presently enqueued on the server
receive queue were sent by them. In order to ensure that these will be
woken up once space becomes again available, the present unix_dgram_poll
routine does a second sock_poll_wait call with the peer_wait wait queue
of the server socket as queue argument (unix_dgram_recvmsg does a wake
up on this queue after a datagram was received). This is inherently
problematic because the server socket is only guaranteed to remain alive
for as long as the client still holds a reference to it. In case the
connection is dissolved via connect or by the dead peer detection logic
in unix_dgram_sendmsg, the server socket may be freed despite "the
polling mechanism" (in particular, epoll) still has a pointer to the
corresponding peer_wait queue. There's no way to forcibly deregister a
wait queue with epoll.
Based on an idea by Jason Baron, the patch below changes the code such
that a wait_queue_t belonging to the client socket is enqueued on the
peer_wait queue of the server whenever the peer receive queue full
condition is detected by either a sendmsg or a poll. A wake up on the
peer queue is then relayed to the ordinary wait queue of the client
socket via wake function. The connection to the peer wait queue is again
dissolved if either a wake up is about to be relayed or the client
socket reconnects or a dead peer is detected or the client socket is
itself closed. This enables removing the second sock_poll_wait from
unix_dgram_poll, thus avoiding the use-after-free, while still ensuring
that no blocked writer sleeps forever.
Signed-off-by: Rainer Weikusat <rweikusat@mobileactivedefense.com> Fixes: ec0d215f9420 ("af_unix: fix 'poll for write'/connected DGRAM sockets") Reviewed-by: Jason Baron <jbaron@akamai.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
Commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown")
fixed a problem with excessive retransmissions in the SHUTDOWN_PENDING by not
resetting the association overall_error_count. This allowed the association
to better enforce assoc.max_retrans limit.
However, the same issue still exists when the association is in SHUTDOWN_RECEIVED
state. In this state, HB-ACKs will continue to reset the overall_error_count
for the association would extend the lifetime of association unnecessarily.
This patch solves this by resetting the overall_error_count whenever the current
state is small then SCTP_STATE_SHUTDOWN_PENDING. As a small side-effect, we
end up also handling SCTP_STATE_SHUTDOWN_ACK_SENT and SCTP_STATE_SHUTDOWN_SENT
states, but they are not really impacted because we disable Heartbeats in those
states.
Fixes: Commit f8d960524328 ("sctp: Enforce retransmission limit during shutdown") Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by: Vlad Yasevich <vyasevich@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Zefan Li <lizefan@huawei.com>
In pfkey_sendmsg the net mutex is taken and then pfkey_broadcast takes
the RCU lock.
Since pfkey_broadcast takes the RCU lock the allocation argument is
pointless since GFP_ATOMIC must be used between the rcu_read_{,un}lock.
The one call outside of rcu can be done with GFP_KERNEL.
Fixes: 7f6b9dbd5afbd ("af_key: locking change") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
The current semaphore code allows a potential use after free: in
exit_sem we may free the task's sem_undo_list while there is still
another task looping through the same semaphore set and cleaning the
sem_undo list at freeary function (the task called IPC_RMID for the same
semaphore set).
For example, with a test program [1] running which keeps forking a lot
of processes (which then do a semop call with SEM_UNDO flag), and with
the parent right after removing the semaphore set with IPC_RMID, and a
kernel built with CONFIG_SLAB, CONFIG_SLAB_DEBUG and
CONFIG_DEBUG_SPINLOCK, you can easily see something like the following
in the kernel log:
I wasn't able to trigger any badness on a recent kernel without the
proper config debugs enabled, however I have softlockup reports on some
kernel versions, in the semaphore code, which are similar as above (the
scenario is seen on some servers running IBM DB2 which uses semaphore
syscalls).
The patch here fixes the race against freeary, by acquiring or waiting
on the sem_undo_list lock as necessary (exit_sem can race with freeary,
while freeary sets un->semid to -1 and removes the same sem_undo from
list_proc or when it removes the last sem_undo).
After the patch I'm unable to reproduce the problem using the test case
[1].
void create_set()
{
int i, j;
pid_t p;
union {
int val;
struct semid_ds *buf;
unsigned short int *array;
struct seminfo *__buf;
} un;
/* Create and initialize semaphore set */
for (i = 0; i < NSET; i++) {
sid[i] = semget(IPC_PRIVATE , NSEM, 0644 | IPC_CREAT);
if (sid[i] < 0) {
perror("semget");
exit(EXIT_FAILURE);
}
}
un.val = 0;
for (i = 0; i < NSET; i++) {
for (j = 0; j < NSEM; j++) {
if (semctl(sid[i], j, SETVAL, un) < 0)
perror("semctl");
}
}
/* Launch threads that operate on semaphore set */
for (i = 0; i < NSEM * NSET * NSET; i++) {
p = fork();
if (p < 0)
perror("fork");
if (p == 0)
thread();
}
/* Free semaphore set */
for (i = 0; i < NSET; i++) {
if (semctl(sid[i], NSEM, IPC_RMID))
perror("IPC_RMID");
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
int main(int argc, char **argv)
{
pid_t p;
srand(time(NULL));
while (1) {
p = fork();
if (p < 0) {
perror("fork");
exit(EXIT_FAILURE);
}
if (p == 0) {
create_set();
goto end;
}
/* Wait for forked processes to exit */
while (wait(NULL)) {
if (errno == ECHILD)
break;
};
}
end:
return 0;
}
[akpm@linux-foundation.org: use normal comment layout] Signed-off-by: Herton R. Krzesinski <herton@redhat.com> Acked-by: Manfred Spraul <manfred@colorfullife.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Rafael Aquini <aquini@redhat.com> CC: Aristeu Rozanski <aris@redhat.com> Cc: David Jeffery <djeffery@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4: adjust context] Signed-off-by: Zefan Li <lizefan@huawei.com>
Since fc_fcp_cleanup_cmd() can sleep this function must not
be called while holding a spinlock. This patch avoids that
fc_fcp_cleanup_each_cmd() triggers the following bug:
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Signed-off-by: Vasu Dev <vasu.dev@intel.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Zefan Li <lizefan@huawei.com>
In case of hw iscsi offload, an host can have N-number of active
connections. There can be IO's running on some connections which
make host->host_busy always TRUE. Now if logout from a connection
is tried then the code gets into an infinite loop as host->host_busy
is always TRUE.
iscsi_conn_teardown(....)
{
.........
/*
* Block until all in-progress commands for this connection
* time out or fail.
*/
for (;;) {
spin_lock_irqsave(session->host->host_lock, flags);
if (!atomic_read(&session->host->host_busy)) { /* OK for ERL == 0 */
spin_unlock_irqrestore(session->host->host_lock, flags);
break;
}
spin_unlock_irqrestore(session->host->host_lock, flags);
msleep_interruptible(500);
iscsi_conn_printk(KERN_INFO, conn, "iscsi conn_destroy(): "
"host_busy %d host_failed %d\n",
atomic_read(&session->host->host_busy),
session->host->host_failed);
................
...............
}
}
This is not an issue with software-iscsi/iser as each cxn is a separate
host.
Fix:
Acquiring eh_mutex in iscsi_conn_teardown() before setting
session->state = ISCSI_STATE_TERMINATE.
Signed-off-by: John Soni Jose <sony.john@avagotech.com> Reviewed-by: Mike Christie <michaelc@cs.wisc.edu> Reviewed-by: Chris Leech <cleech@redhat.com> Signed-off-by: James Bottomley <JBottomley@Odin.com>
[lizf: Backported to 3.4: adjust context] Signed-of-by: Zefan Li <lizefan@huawei.com>
When using nested btrees, the top leaves of the top levels contain
block addresses for the root of the next tree down. If we shadow a
shared leaf node the leaf values (sub tree roots) should be incremented
accordingly.
This is only an issue if there is metadata sharing in the top levels.
Which only occurs if metadata snapshots are being used (as is possible
with dm-thinp). And could result in a block from the thinp metadata
snap being reused early, thus corrupting the thinp metadata snap.
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com>
[lizf: Backported to 3.4:
- drop const
- drop changes to remove_one()] Signed-off-by: Zefan Li <lizefan@huawei.com>
projects / thirdparty / kernel / stable.git / log
