When zoning end devices, the driver is not sending device
removal handshake alogrithm to firmware. This results in controller
firmware not sending sas topology add events the next time the device is
added. The fix is the driver should be doing the device removal handshake
even though the PHYSTATUS_VACANT bit is set in the PhyStatus of the
event data. The current design is avoiding the handshake when the
VACANT bit is set in the phy status.
libsas makes use of scsi_schedule_eh() but forgets to clear the
host_eh_scheduled flag in its error handling routine. Because of this,
the error handler thread never gets to sleep; it's constantly awake and
trying to run the error routine leading to console spew and inability to
run anything else (at least on a UP system). The fix is to clear the
flag as we splice the work queue.
Our current handling of medium error assumes that data is returned up
to the bad sector. This assumption holds good for all disk devices,
all DIF arrays and most ordinary arrays. However, an LSI array engine
was recently discovered which reports a medium error without returning
any data. This means that when we report good data up to the medium
error, we've reported junk originally in the buffer as good. Worse,
if the read consists of requested data plus a readahead, and the error
occurs in readahead, we'll just strip off the readahead and report
junk up to userspace as good data with no error.
The fix for this is to have the error position computation take into
account the amount of data returned by the driver using the scsi
residual data. Unfortunately, not every driver fills in this data,
but for those who don't, it's set to zero, which means we'll think a
full set of data was transferred and the behaviour will be identical
to the prior behaviour of the code (believe the buffer up to the error
sector). All modern drivers seem to set the residual, so that should
fix up the LSI failure/corruption case.
Reported-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Since commit 6cd0b1cb872b3bf9fc5de4536404206ab74bafdd "iwlagn: fix
hw-rfkill while the interface is down", we enable interrupts when
device is not ready to receive them. However hardware, when it is in
some inconsistent state, can generate other than rfkill interrupts
and crash the system. I can reproduce crash with "kernel BUG at
drivers/net/wireless/iwlwifi/iwl-agn.c:1010!" message, when forcing
firmware restarts.
To fix only enable rfkill interrupt when down device and after probe.
I checked patch on laptop with 5100 device, rfkill change is still
passed to user space when device is down.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
The hv_netvsc gets RNDIS_STATUS_MEDIA_CONNECT event after the VM
is live migrated. Adding call to netif_notify_peers() for this event
to send GARP (Gratuitous ARP) to notify network peers. Otherwise,
the VM's network connection may stop after a live migration.
This patch should also be applied to stable kernel 2.6.32 and later.
The ni_labpc driver module only requests a shared IRQ for PCI devices,
requesting a non-shared IRQ for non-PCI devices.
As this module is also used by the ni_labpc_cs module for certain
National Instruments PCMCIA cards, it also needs to request a shared IRQ
for PCMCIA devices, otherwise you get a IRQ mismatch with the CardBus
controller.
If anyone comes across a high-speed hub that (by mistake or by design)
claims to have no Transaction Translators, plugging a full- or
low-speed device into it will cause the USB stack to crash. This
patch (as1446) prevents the problem by ignoring such devices, since
the kernel has no way to communicate with them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Andi Kleen <ak@linux.intel.com> Tested-by: Perry Neben <neben@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The major and minor number saved in the product_info structure
were copied from the address instead of the data, causing an
inconsistency in the reported versions during firmware loading:
usb 4-1: firmware: requesting edgeport/down.fw
/usr/src/linux/drivers/usb/serial/io_edgeport.c: downloading firmware version (930) 1.16.4
[..]
/usr/src/linux/drivers/usb/serial/io_edgeport.c: edge_startup - time 3 4328191260
/usr/src/linux/drivers/usb/serial/io_edgeport.c: FirmwareMajorVersion 0.0.4
This can cause some confusion whether firmware loaded successfully
or not.
This patch (as1442) fixes a bug in g_printer: Module parameters should
not be marked "__initdata" if they are accessible in sysfs (i.e., if
the mode value in the module_param() macro is nonzero). Otherwise
attempts to access the parameters will cause addressing violations.
Character-string module parameters must not be marked "__initdata"
if the module can be unloaded, because the kernel needs to access the
parameter variable at unload time in order to free the
dynamically-allocated string.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Andi Kleen <ak@linux.intel.com> CC: Roland Kletzing <devzero@web.de> CC: Craig W. Nadler <craig@nadler.us> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is
used to compute the size in a dma_alloc_coherent() call, but then it
gets changed later on. As a result, the corresponding call to
dma_free_coherent() passes a different size from the original
allocation. Fix the problem by adjusting ehci->periodic_size before
carrying out any of the memory allocations.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Andi Kleen <ak@linux.intel.com> Tested-by: Larry Finger <Larry.Finger@lwfinger.net> CC: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
/drivers/usb/serial/option.c: Adding support for Cinterion's HC25, HC28,
HC28J, EU3-E, EU3-P and PH8 by correcting/adding Cinterion's and
Siemens' Vendor IDs as well as Product IDs and USB_DEVICE tuples
I found the original patch on the db0fhn repeater wiki (couldn't find the email
of the origial author) I guess it was never commited.
I updated and added some Icom HAM-radio devices to the ftdi driver.
Added extra comments to make clear what devices it are.
This patch (as1438) adds an unusual_devs entry for the MagicPixel
FW_Omega2 chip, used in the CamSport Evo camera. The firmware
incorrectly reports a vendor-specific bDeviceClass.
The TrekStor DataStation maxi g.u external hard drive enclosure uses a
JMicron USB to SATA chip which needs the US_FL_IGNORE_RESIDUE flag to work
properly.
Device ID removed 0x10C4/0x8149 for West Mountain Radio Computerized
Battery Analyzer. This device is actually based on a SiLabs C8051Fxxx,
see http://www.etheus.net/SiUSBXp_Linux_Driver for further info.
Alan's commit 335f8514f200e63d689113d29cb7253a5c282967 introduced
.carrier_raised function in several drivers. That also means
tty_port_block_til_ready can now suspend the process trying to open the serial
port when Carrier Detect is low and put it into tty_port.open_wait queue. We
need to wake up the process when Carrier Detect goes high and trigger TTY
hangup when CD goes low.
Some of the devices do not report modem status line changes, or at least we
don't understand the status message, so for those we remove .carrier_raised
again.
Functions set_fan_min() and set_fan_div() assume that the fan_div
values have already been read from the register. The driver currently
doesn't initialize them at load time, they are only set when function
via686a_update_device() is called. This means that set_fan_min() and
set_fan_div() misbehave if, for example, "sensors -s" is called
before any monitoring application (e.g. "sensors") is has been run.
Fix the problem by always initializing the fan_div values at device
bind time.
When ASPM PM Feature is enabled on UMI link, devices that use ISOC stream of
data transfer may be exposed to longer latency causing less than optimal per-
formance of the device. The longer latencies are normal and are due to link
wake time coming out of low power state which happens frequently to save
power when the link is not active.
The following code will make exception for certain features of ASPM to be by
passed and keep the logic normal state only when the ISOC device is connected
and active. This change will allow the device to run at optimal performance
yet minimize the impact on overall power savings.
Signed-off-by: Alex He <alex.he@amd.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
In the vhci_urb_dequeue() function the TCP connection is checked twice.
Each time when the TCP connection is closed the URB is unlinked and given
back. Remove the second attempt of unlinking and giving back of the URB completely.
This patch fixes the bug described at https://bugzilla.kernel.org/show_bug.cgi?id=24872 .
David Howells [Thu, 31 Mar 2011 18:57:36 +0000 (11:57 -0700)]
Fix cred leak in AF_NETLINK
Patch cab9e9848b9a8283b0504a2d7c435a9f5ba026de to the 2.6.35.y stable tree
stored a ref to the current cred struct in struct scm_cookie. This was fine
with AF_UNIX as that calls scm_destroy() from its packet sending functions, but
AF_NETLINK, which also uses scm_send(), does not call scm_destroy() - meaning
that the copied credentials leak each time SCM data is sent over a netlink
socket.
This can be triggered quite simply on a Fedora 13 or 14 userspace with the
2.6.35.11 kernel (or something based off of that) by calling:
#!/bin/bash
for ((i=0; i<100; i++))
do
su - -c /bin/true
cut -d: -f1 /proc/slabinfo | grep 'cred\|key\|task_struct'
cat /proc/keys | wc -l
done
This leaks the session key that pam_keyinit creates for 'su -', which appears
in /proc/keys as being revoked (has the R flag set against it) afterward su is
called.
Furthermore, if CONFIG_SLAB=y, then the cred and key slab object usage counts
can be viewed and seen to increase. The key slab increases by one object per
loop, and this can be seen after the system has had a couple of minutes to
stand after the script above has been run on it.
If the system is working correctly, the key and cred counts should return to
roughly what they were before.
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Use a safer coding style for the hotkey keymap. This does not fix any
problems, as the current code is correct. But it might help avoid
mistakes in the future.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Matthew Garrett <mjg@redhat.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
If we receive two PERF_RECORD_EXIT for the same thread, we can end up
reusing session->last_match and trying to remove the thread twice from
the rb_tree, causing a segfault, so invalidade last_match in
perf_session__remove_thread.
Receiving two PERF_RECORD_EXIT for the same thread is a bug, but its a
harmless one if we make the tool more robust, like this patch does.
Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <new-submission> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs'
added a check for copying the skb if it's shared, however the tx info variable
still points at the cb of the old skb
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Avoid the reference whenever the frame copy is unsuccessful
regardless of the debug message being suppressed or printed.
Cc: stable@kernel.org [2.6.27+] Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
We can not call del_timer_sync(addba_resp_timer) from
___ieee80211_stop_tx_ba_session(), as this function can be called from
that timer callback. To fix, simply use not synchronous del_timer().
The flag PDN_INV indicates that the sensor pin S_PWR_DN has not the same
value as other webcams with the same sensor. For now, only two webcams have
been so detected: the Microsoft's VX1000 and VX3000.
posix-cpu-timers.c correctly assumes that the dying process does
posix_cpu_timers_exit_group() and removes all !CPUCLOCK_PERTHREAD
timers from signal->cpu_timers list.
But, it also assumes that timer->it.cpu.task is always the group
leader, and thus the dead ->task means the dead thread group.
This is obviously not true after de_thread() changes the leader.
After that almost every posix_cpu_timer_ method has problems.
It is not simple to fix this bug correctly. First of all, I think
that timer->it.cpu should use struct pid instead of task_struct.
Also, the locking should be reworked completely. In particular,
tasklist_lock should not be used at all. This all needs a lot of
nontrivial and hard-to-test changes.
Change __exit_signal() to do posix_cpu_timers_exit_group() when
the old leader dies during exec. This is not the fix, just the
temporary hack to hide the problem for 2.6.37 and stable. IOW,
this is obviously wrong but this is what we currently have anyway:
cpu timers do not work after mt exec.
In theory this change adds another race. The exiting leader can
detach the timers which were attached to the new leader. However,
the window between de_thread() and release_task() is small, we
can pretend that sys_timer_create() was called before de_thread().
In arch/x86/kernel/microcode_intel.c::generic_load_microcode()
we have this:
while (leftover) {
...
if (get_ucode_data(mc, ucode_ptr, mc_size) ||
microcode_sanity_check(mc) < 0) {
vfree(mc);
break;
}
...
}
if (mc)
vfree(mc);
This will cause a double free of 'mc'. This patch fixes that by
just removing the vfree() call in the loop since 'mc' will be
freed nicely just after we break out of the loop.
There's also a second change in the patch. I noticed a lot of
checks for pointers being NULL before passing them to vfree().
That's completely redundant since vfree() deals gracefully with
being passed a NULL pointer. Removing the redundant checks
yields a nice size decrease for the object file.
Size before the patch:
text data bss dec hex filename
4578 240 1032 5850 16da arch/x86/kernel/microcode_intel.o
Size after the patch:
text data bss dec hex filename
4489 240 984 5713 1651 arch/x86/kernel/microcode_intel.o
When stacking devices, a request_queue is not always available. This
forced us to have a no_cluster flag in the queue_limits that could be
used as a carrier until the request_queue had been set up for a
metadevice.
There were several problems with that approach. First of all it was up
to the stacking device to remember to set queue flag after stacking had
completed. Also, the queue flag and the queue limits had to be kept in
sync at all times. We got that wrong, which could lead to us issuing
commands that went beyond the max scatterlist limit set by the driver.
The proper fix is to avoid having two flags for tracking the same thing.
We deprecate QUEUE_FLAG_CLUSTER and use the queue limit directly in the
block layer merging functions. The queue_limit 'no_cluster' is turned
into 'cluster' to avoid double negatives and to ease stacking.
Clustering defaults to being enabled as before. The queue flag logic is
removed from the stacking function, and explicitly setting the cluster
flag is no longer necessary in DM and MD.
Reported-by: Ed Lin <ed.lin@promise.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Jens Axboe <jaxboe@fusionio.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
idle_balance() drops/retakes rq->lock, leaving the previous task
vulnerable to set_tsk_need_resched(). Clear it after we return
from balancing instead, and in setup_thread_stack() as well, so
no successfully descheduled or never scheduled task has it set.
Need resched confused the skip_clock_update logic, which assumes
that the next call to update_rq_clock() will come nearly immediately
after being set. Make the optimization robust against the waking
a sleeper before it sucessfully deschedules case by checking that
the current task has not been dequeued before setting the flag,
since it is that useless clock update we're trying to save, and
clear unconditionally in schedule() proper instead of conditionally
in put_prev_task().
Sjoerd Simons reports that, without using position_fix=1, recording
experiences overruns. Work around that by applying the LPIB quirk
for his hardware.
Under memory pressure, the mac80211 mesh code
may helpfully print a message that it failed
to clone a mesh frame and then will proceed
to crash trying to use it anyway. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
While separating out BMDMA irq handler from SFF, commit c3b28894
(libata-sff: separate out BMDMA irq handler) incorrectly made
__ata_sff_port_intr() consider an IRQ to be an idle one if the host
state was transitioned to HSM_ST_ERR by ata_bmdma_port_intr().
This makes BMDMA drivers ignore IRQs reporting host bus error which
leads to timeouts instead of triggering EH immediately. Fix it by
making __ata_sff_port_intr() consider the IRQ to be an idle one iff
the state is HSM_ST_IDLE. This is equivalent to adding HSM_ST_ERR to
the "break"ing case but less error-prone.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Andi Kleen <ak@linux.intel.com> Reported-by: Antonio Toma <antonio.toma@gmail.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thus without the patch, with the boot parameters 'tcb selinux=0', adding
the above 'dont_measure obj_type=var_log_t' rule to the default IMA TCB
measurement policy, would result in nothing being measured. The patch
prevents the default TCB policy from being replaced.
The load_mixer_volumes() function, which can be triggered by
unprivileged users via the SOUND_MIXER_SETLEVELS ioctl, is vulnerable to
a buffer overflow. Because the provided "name" argument isn't
guaranteed to be NULL terminated at the expected 32 bytes, it's possible
to overflow past the end of the last element in the mixer_vols array.
Further exploitation can result in an arbitrary kernel write (via
subsequent calls to load_mixer_volumes()) leading to privilege
escalation, or arbitrary kernel reads via get_mixer_levels(). In
addition, the strcmp() may leak bytes beyond the mixer_vols array.
The DisplayPort standard (1.1a) states that:
The I2C-over-AUX Reply field is valid only when Native AUX CH Reply
field is AUX_ACK (00). When Native AUX CH Reply field is not 00, then,
I2C-over-AUX Reply field must be 00 and be ignored.
This fixes broken EDID reading when using an active DisplayPort to
duallink DVI converter. If the AUX CH replier chooses to defer the
transaction, a short read occurs and erroneous data is returned as
the i2c reply due to a lack of length checking and failure to check
for AUX ACK.
As a result, broken EDIDs can look like:
0 1 2 3 4 5 6 7 8 9 a b c d e f 0123456789abcdef
00: bc bc bc ff bc bc bc ff bc bc bc ac bc bc bc 45 ???.???.???????E
10: bc bc bc 10 bc bc bc 34 bc bc bc ee bc bc bc 4c ???????4???????L
20: bc bc bc 50 bc bc bc 00 bc bc bc 40 bc bc bc 00 ???P???.???@???.
30: bc bc bc 01 bc bc bc 01 bc bc bc a0 bc bc bc 40 ???????????????@
40: bc bc bc 00 bc bc bc 00 bc bc bc 00 bc bc bc 55 ???.???.???.???U
50: bc bc bc 35 bc bc bc 31 bc bc bc 20 bc bc bc fc ???5???1??? ????
60: bc bc bc 4c bc bc bc 34 bc bc bc 46 bc bc bc 00 ???L???4???F???.
70: bc bc bc 38 bc bc bc 11 bc bc bc 20 bc bc bc 20 ???8??????? ???
80: bc bc bc ff bc bc bc ff bc bc bc ff bc bc bc ff ???.???.???.???.
...
Signed-off-by: David Flynn <davidf@rd.bbc.co.uk> Signed-off-by: Andi Kleen <ak@linux.intel.com>
[ickle: fix up some surrounding checkpatch warnings] Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Only reset the grbm blocks, srbm tends to lock the GPU
if not done properly and in most cases is not necessary.
Also, no need to call asic init after reset the grbm blocks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Andi Kleen <ak@linux.intel.com> Reviewed-by: Jerome Glisse <jglisse@redhat.com> Signed-off-by: Dave Airlie <airlied@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable preemption in init_ibs(). The function only checks the
ibs capabilities and sets up pci devices (if necessary). It runs
only on one cpu but operates with the local APIC and some MSRs,
thus it is better to disable preemption.
[ 7.034377] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/483
[ 7.034385] caller is setup_APIC_eilvt+0x155/0x180
[ 7.034389] Pid: 483, comm: modprobe Not tainted 2.6.37-rc1-20101110+ #1
[ 7.034392] Call Trace:
[ 7.034400] [<ffffffff812a2b72>] debug_smp_processor_id+0xd2/0xf0
[ 7.034404] [<ffffffff8101e985>] setup_APIC_eilvt+0x155/0x180
[ ... ]
rdc321x-wdt currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
The current code mis-calculates the ramoops header size, leading to an
overflow over the next record at best, or over a non-allocated region at
worst. Fix that calculation.
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com> Acked-by: Marco Stornelli <marco.stornelli@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Match the buffer size to the amount of initialized values. Before, it was
one too big and thus destroyed the neighbouring register causing the clock
to run at false speeds.
Reported-by: Andre van Rooyen <a.v.rooyen@sercom.nl> Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Andi Kleen <ak@linux.intel.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the error-path where PM notifies PM_POST_RESTORE, the rescan-blockage
should be cleared as well. Otherwise it'll be never re-probed.
Also, as a bonus, this fixes a bug in S4 with user-mode suspend in the
current code, as it sends PM_POST_RESTORE instead of
PM_POST_HIBERNATION wrongly.
Based on report made by Yauhen in:
"MMC: Fix multiblock SDIO transfers in AT91 MCI" patch,
I report those changes to the brother driver: atmel-mci.
So, this patch sets SDIO transfer types: SDIO block and SDIO byte
transfers instead of using ordinary MMC block transfers.
It is checking opcode for SDIO CMD53 and setting transfer
type in MCI_CMDR register properly.
The AT91 MCI has special SDIO transfer types: SDIO block and SDIO byte
transfers, but at91_mci driver doesn't use them and handles all SDIO
transfers as ordinary MMC block transfers. This causes problems for
multiple-block SDIO transfers (in particular for 256-bytes blocks).
Fix this situation by checking the opcode for SDIO CMD53 and setting
the transfer type in the AT91_MCI_CMDR register properly.
This patch was tested with libertas SDIO driver: problem with TX
timeouts on big packets was eliminated.
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org> Signed-off-by: Andres Salomon <dilinger@queued.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
The first bug will only show up with broken xHCI hosts with Extended
Capabilities registers that have duplicate port speed entries for the same
port. The idea with the original code was to set the port_array entry to
-1 if the duplicate port speed entry said the port was a different speed
than the original port speed entry. That would mean that later, the port
would not be exposed to the USB core. Unfortunately, I forgot a continue
statement, and the port_array entry would just be overwritten in the next
line.
The second bug would happen if there are conflicting port speed registers
(so that some entry in port_array is -1), or one of the hardware port
registers was not described in the port speed registers (so that some
entry in port_array is 0). The code that sets up the usb2_ports array
would accidentally claim those ports. That wouldn't really cause any
user-visible issues, but it is a bug.
This patch should go into the stable trees that have the port array and
USB 3.0 port disabling prevention patches.
When the message length is greater than 127, the length field in the header
is built incorrectly. According to the spec, when the length is less than 128
the length field is a single byte formatted as: bbbbbbb1. When it is greater
than 127 then the field is two bytes of the format: bbbbbbb0bbbbbbbb.
Signed-off-by: Ken Mills <ken.k.mills@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Add an unusual_devs entry for the Samsung YP-CP3 MP4 player.
User was getting the following errors in dmesg:
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: reset high speed USB device using ehci_hcd and address 2
usb 2-6: USB disconnect, address 2
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sdb:<2>ldm_validate_partition_table(): Disk read failed.
Dev sdb: unable to read RDB block 0
unable to read partition table
Signed-off-by: Vitaly Kuznetsov <vitty@altlinux.ru> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Andi Kleen <ak@linux.intel.com> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The install_special_mapping routine (used, for example, to setup the
vdso) skips the security check before insert_vm_struct, allowing a local
attacker to bypass the mmap_min_addr security restriction by limiting
the available pages for special mappings.
bprm_mm_init() also skips the check, and although I don't think this can
be used to bypass any restrictions, I don't see any reason not to have
the security check.
Lenovo S10-3t's ClickPad is a 2-button ClickPad that reports BTN_LEFT
and BTN_RIGHT as normal touchpad, unlike the 1-button ClickPad used in
HP mini 210 that reports solely BTN_MIDDLE.
In 0xc0-cap response, the 1-button ClickPad has the 20-bit set while
2-button ClickPad has the 8-bit set.
This patch makes the kernel only handle 1-button ClickPad specially,
and treat 2-button ClickPad in the same fashion as regular touchpads.
This fixes kernel bug #18122 and MeeGo bug #4807.
Signed-off-by: Yan Li <yan.i.li@intel.com> Signed-off-by: Dmitry Torokhov <dtor@mail.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
During initialization each driver reads the default TX power
for each individual channel. However mac80211 only accepts the
maximum value (which is also handled as default value).
As a result, the TX power of the device was being limited to
the default value, which is often quite low compared to the
real maximum acceptable value.
This patch allows each driver to set the maximum value on a
per-channel basis which is forwarded to mac80211. The default
value will be preserved for now, in case we want to update
mac80211 to differentiate between the maximum and default txpower.
This fixes bug complaining about limited TX power values like:
https://bugzilla.kernel.org/show_bug.cgi?id=16358
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
On platforms with Intel 7500 chipset, there were some reports of system
hang/NMI's during kexec/kdump in the presence of interrupt-remapping enabled.
During kdump, there is a window where the devices might be still using old
kernel's interrupt information, while the kdump kernel is coming up. This can
cause vt-d faults as the interrupt configuration from the old kernel map to
null IRTE entries in the new kernel etc. (with out interrupt-remapping enabled,
we still have the same issue but in this case we will see benign spurious
interrupt hit the new kernel).
Based on platform config settings, these platforms seem to generate NMI/SMI
when a vt-d fault happens and there were reports that the resulting SMI causes
the system to hang.
Fix it by masking vt-d spec defined errors to platform error reporting logic.
VT-d spec related errors are already handled by the VT-d OS code, so need to
report the same error through other channels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <1291667190.2675.8.camel@sbsiddha-MOBL3.sc.intel.com> Reported-by: Max Asbock <masbock@linux.vnet.ibm.com> Reported-and-tested-by: Takao Indoh <indou.takao@jp.fujitsu.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In x2apic mode, we need to set the upper address register of the fault
handling interrupt register of the vt-d hardware. Without this
irq migration of the vt-d fault handling interrupt is broken.
Fault handling is getting enabled after enabling the interrupt-remapping (as
the success of interrupt-remapping can affect the apic mode and hence the
fault handling mode).
Hence there can potentially be some faults between the window of enabling
interrupt-remapping in the vt-d and the fault-handling of the vt-d units.
Handle any previous faults after enabling the vt-d fault handling.
For v2.6.38 cleanup, need to check if we can remove the dmar_fault() in the
enable_intr_remapping() and see if we can enable fault handling along with
enabling intr-remapping.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20101201062244.630417138@intel.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Interrupt-remapping gets enabled very early in the boot, as it determines the
apic mode that the processor can use. And the current code enables the vt-d
fault handling before the setup_local_APIC(). And hence the APIC LDR registers
and data structure in the memory may not be initialized. So the vt-d fault
handling in logical xapic/x2apic modes were broken.
Fix this by enabling the vt-d fault handling in the end_local_APIC_setup()
A cleaner fix of enabling fault handling while enabling intr-remapping
will be addressed for v2.6.38. [ Enabling intr-remapping determines the
usage of x2apic mode and the apic mode determines the fault-handling
configuration. ]
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20101201062244.541996375@intel.com> Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com> Acked-by: Chris Wright <chrisw@sous-sol.org> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vdso Makefile passes linker-style -m options not to the linker but
to gcc. This happens to work with earlier gcc, but fails with gcc
4.6. Pass gcc-style -m options, instead.
Note: all currently supported versions of gcc supports -m32, so there
is no reason to conditionalize it any more.
Reported-by: H. J. Lu <hjl.tools@gmail.com> Signed-off-by: H. Peter Anvin <hpa@linux.intel.com> Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <tip-*@git.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The file_ops struct for the "trace" special file defined llseek as seq_lseek().
However, if the file was opened for writing only, seq_open() was not called,
and the seek would dereference a null pointer, file->private_data.
This patch introduces a new wrapper for seq_lseek() which checks if the file
descriptor is opened for reading first. If not, it does nothing.
When we fail to start a raid10 for some reason, we call
md_unregister_thread to kill the thread that was created.
Unfortunately md_thread() will then make one call into the handler
(raid10d) even though md_wakeup_thread has not been called. This is
not safe and as md_unregister_thread is called after mddev->private
has been set to NULL, it will definitely cause a NULL dereference.
So fix this at both ends:
- md_thread should only call the handler if THREAD_WAKEUP has been
set.
- raid10 should call md_unregister_thread before setting things
to NULL just like all the other raid modules do.
With v0.90 metadata, a hot-spare does not become a full member of the
array until recovery is complete. So if we re-add such a device to
the array, we know that all of it is as up-to-date as the event count
would suggest, and so it a bitmap-based recovery is possible.
However with v1.x metadata, the hot-spare immediately becomes a full
member of the array, but it record how much of the device has been
recovered. If the array is stopped and re-assembled recovery starts
from this point.
When such a device is hot-added to an array we currently lose the 'how
much is recovered' information and incorrectly included it as a full
in-sync member (after bitmap-based fixup).
This is wrong and unsafe and could corrupt data.
So be more careful about setting saved_raid_disk - which is what
guides the re-adding of devices back into an array.
The new code matches the code in slot_store which does a similar
thing, which is encouraging.
Andreas Herrmann [Thu, 16 Dec 2010 20:29:37 +0000 (21:29 +0100)]
x86, amd: Fix panic on AMD CPU family 0x15
[The mainline kernel doesn't have this problem. Commit "(23588c3) x86,
amd: Add support for CPUID topology extension of AMD CPUs" removed the
family check. But 2.6.32.y needs to be fixed.]
This CPU family check is not required -- existence of the NodeId MSR
is indicated by a CPUID feature flag which is already checked in
amd_fixup_dcm() -- and it needlessly prevents amd_fixup_dcm() to be
called for newer AMD CPUs.
In worst case this can lead to a panic in the scheduler code for AMD
family 0x15 multi-node AMD CPUs. I just have a picture of VGA console
output so I can't copy-and-paste it herein, but the call stack of such
a panic looked like:
The mainline kernel doesn't have this problem. Commit "(23588c3) x86,
amd: Add support for CPUID topology extension of AMD CPUs" removed the
family check. But 2.6.32.y needs to be fixed.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
If inotify_init is unable to allocate a new file for the new inotify
group we leak the new group. This patch drops the reference on the
group on file allocation failure.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com> Signed-off-by: Eric Paris <eparis@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
There are some situations (e.g. in __pm_generic_call()), where
pm_runtime_suspended() is used to decide whether or not to execute
a device's (system) ->suspend() callback. The callback is not
executed if pm_runtime_suspended() returns true, but it does so
for devices that don't even support runtime PM, because the
power.disable_depth device field is ignored by it. This leads to
problems (i.e. devices are not suspened when they should), so rework
pm_runtime_suspended() so that it returns false if the device's
power.disable_depth field is different from zero.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andi Kleen <ak@linux.intel.com>
projects / thirdparty / kernel / stable.git / log
