The Quality-of-Service (QsS) node stores/restores specific
register contents when the power domains is turned off/on.
Add QoS node so that they can connect to the power domain.
Patrick Wildt [Sun, 2 Mar 2025 20:08:24 +0000 (21:08 +0100)]
arm64: dts: rockchip: add MNT Reform 2 laptop
MNT Reform 2 is an open source laptop with replaceable CPU modules,
including a version with the RK3588-based MNT RCORE[1], which is based
on Firefly's iCore-3588Q SoM:
- Rockchip RK3588
- Quad A76 and Quad A55 CPU
- 6 TOPS NPU
- up to 32GB LPDDR4x RAM
- SD Card slot
- Gigabit ethernet port
- HDMI port
- 2x mPCIe ports for WiFi or NVMe
- 3x USB 3.0 Type-A HOST port
[1] https://shop.mntre.com/products/mnt-reform
Co-developed-by: "Lukas F. Hartmann" <lukas@mntre.com> Signed-off-by: "Lukas F. Hartmann" <lukas@mntre.com> Signed-off-by: Patrick Wildt <patrick@blueri.se> Link: https://lore.kernel.org/r/Z8S6uDM634KJuyKP@windev.fritz.box Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jonas Karlman [Fri, 28 Feb 2025 06:40:10 +0000 (06:40 +0000)]
arm64: dts: rockchip: Add pinctrl and gpio nodes for RK3528
Add pinctrl and gpio nodes for RK3528 and import rk3528-pinctrl.dtsi
from vendor linux-6.1-stan-rkr5 kernel with the hdmi-pins-idle node
removed due to missing label reference to pcfg_output_low_pull_down.
Heiko Stuebner [Fri, 28 Feb 2025 15:08:53 +0000 (16:08 +0100)]
arm64: dts: rockchip: add usb typec host support to rk3588-jaguar
Jaguar has two type-c ports connected to fusb302 controllers that can
work both in host and device mode and can also run in display-port
altmode.
While these ports can work in dual-role data mode, they do not support
powering the device itself as power-sink. This causes issues because
the current infrastructure does not cope well with dual-role data
without dual-role power.
So add the necessary nodes for the type-c controllers as well as enable
the relevant core usb nodes. So far host modes works reliably, but
device-mode does not. So devicemode needs more investigation.
arm64: dts: rockchip: Add GPU power domain regulator dependency for RK3588
Enabling the GPU power domain requires that the GPU regulator is
enabled. The regulator is enabled at boot time, but gets disabled
automatically when there are no users.
This means the system might run into a failure state hanging the
whole system for the following use cases:
* if the GPU driver is being probed late (e.g. build as a
module and firmware is not in initramfs), the regulator
might already have been disabled. In that case the power
domain is enabled before the regulator.
* unbinding the GPU driver will disable the PM domain and
the regulator. When the driver is bound again, the PM
domain will be enabled before the regulator and error
appears.
Avoid this by adding an explicit regulator dependency to the
power domain.
Tested-by: Heiko Stuebner <heiko@sntech.de> Reported-by: Adrián Martínez Larumbe <adrian.larumbe@collabora.com> Tested-by: Adrian Larumbe <adrian.larumbe@collabora.com> # On Rock 5B Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20250220-rk3588-gpu-pwr-domain-regulator-v6-8-a4f9c24e5b81@kernel.org Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jimmy Hon [Sat, 22 Feb 2025 19:33:30 +0000 (13:33 -0600)]
arm64: dts: rockchip: Add Orange Pi 5 Ultra board
The RK3588 Single Board Computer includes
- eMMC
- microSD
- UART
- 2 PWM LEDs
- RTC
- RTL8125 network controller on PCIe 2.0x1.
- M.2 M-key connector routed to PCIe 3.0x4
- PWM controlled heat sink fan.
- 2 USB2 ports
- lower USB3 port
- upper USB3 port with OTG capability
- Mali GPU
- SPI NOR flash
- Mask Rom button
- Analog audio using es8388 codec via the headset jack and onboard mic
- HDMI1
- HDMI IN
the vcc5v0_usb30 regulator shares the same enable gpio pin as the
vcc5v0_usb20 regulator.
The Orange Pi 5 Ultra is a single board computer powered by the Rockchip
RK3588 with similar board layout as the 5 Max but with the HDMI0 swapped
for HDMI IN.
Jimmy Hon [Sat, 22 Feb 2025 19:33:29 +0000 (13:33 -0600)]
dt-bindings: arm: rockchip: Add Xunlong Orange Pi 5 Ultra
Add devicetree binding for the Xunlong Orange Pi 5 Ultra board.
The Orange Pi 5 Ultra is a single board computer powered by the Rockchip
RK3588 with similar board layout as the 5 Max but with the HDMI0 swapped
for HDMI IN.
Jimmy Hon [Sat, 22 Feb 2025 19:33:28 +0000 (13:33 -0600)]
arm64: dts: rockchip: Adapt to differences between Orange Pi 5 Max and Ultra
The Orange Pi 5 Plus and Orange Pi 5 Max have 2SK3018s attached to the
PWM LEDs. The Orange Pi 5 Ultra does not, and thus needs the PWM
polarity inverted.
Also remove the model/compatible from the dtsi. It should be at the
board level only.
Detlev Casanova [Mon, 17 Feb 2025 21:47:41 +0000 (16:47 -0500)]
arm64: dts: rockchip: Add HDMI audio outputs for rk3588
For hdmi0_sound, use the simple-audio-card driver with the hdmi0 QP node
as CODEC and the i2s5 device as CPU.
Similarly for hdmi1_sound, the CODEC is the hdmi1 node and the CPU is
i2s6, but only added in the rk3588-extra.dtsi device tree as the second
TX HDMI port is not available on base versions of the SoC.
The simple-audio-card,mclk-fs value is set to 128 as it is done in
the downstream driver.
The #sound-dai-cells value is set to 0 in the hdmi0 and hdmi1 nodes so
that they can be used as audio codec nodes.
arm64: dts: rockchip: Add HDMI1 PHY PLL clock source to VOP2 on RK3588
VOP2 on RK3588 is able to use the HDMI PHY PLL as an alternative and
more accurate pixel clock source to improve handling of display modes up
to 4K@60Hz on video ports 0, 1 and 2.
The HDMI1 PHY PLL clock source cannot be added directly to vop node in
rk3588-base.dtsi, along with the HDMI0 related one, because HDMI1 is an
optional feature and its PHY node belongs to a separate (extra) DT file.
Therefore, add the HDMI1 PHY PLL clock source to VOP2 by overwriting its
clocks & clock-names properties in the extra DT file.
arm64: dts: rockchip: Enable HDMI1 PHY clk provider on RK3588
Since commit c4b09c562086 ("phy: phy-rockchip-samsung-hdptx: Add clock
provider support"), the HDMI PHY PLL can be used as an alternative and
more accurate pixel clock source for VOP2 to improve display modes
handling on RK3588 SoC.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI1 PHY.
Yao Zi [Mon, 17 Feb 2025 06:11:45 +0000 (06:11 +0000)]
arm64: dts: rockchip: Add clock generators for RK3528 SoC
Add dt node for RK3528 clock and reset unit. Clock "gmac0_clk" is
generated by internal Ethernet phy, a fixed clock node is added as a
placeholder to avoid orphans.
Yao Zi [Mon, 17 Feb 2025 06:11:42 +0000 (06:11 +0000)]
dt-bindings: clock: Document clock and reset unit of RK3528
There are two types of clocks in RK3528 SoC, CRU-managed and
SCMI-managed. Independent IDs are assigned to them.
For the reset part, differing from previous Rockchip SoCs and
downstream bindings which embeds register offsets into the IDs, gapless
numbers starting from zero are used.
Quentin Schulz [Tue, 18 Feb 2025 11:49:20 +0000 (12:49 +0100)]
arm64: dts: rockchip: disable I2C2 bus by default on RK3588 Tiger
RK3588 Tiger routes I2C2 signals to the Q7 Camera FFC connector (P2) but
nothing on the SoM itself is on that bus, therefore it'll be up to the
adapter connected to the Q7 Camera FFC connector (P2) to enable the I2C2
controller, if need be.
Quentin Schulz [Tue, 18 Feb 2025 11:49:19 +0000 (12:49 +0100)]
arm64: dts: rockchip: enable I2C3 in Haikou carrierboard, not Ringneck DTSI
PX30 Ringneck only exposes I2C3 as LVDS_BLC_CLK/DAT on Q7 golden fingers
but nothing is on that bus on the SoM itself. Therefore, let's enable
the I2C3 bus where it makes sense, in the Haikou carrierboard DTS.
Quentin Schulz [Tue, 18 Feb 2025 11:49:18 +0000 (12:49 +0100)]
arm64: dts: rockchip: enable Ethernet in Haikou carrierboard, not Puma DTSI
The signals are exposed on Q7 golden fingers but it's not a given that
the carrierboard will have an Ethernet jack. So let's move the enabling
of the Ethernet controller to the carrierboard DTS instead.
Quentin Schulz [Tue, 18 Feb 2025 11:49:17 +0000 (12:49 +0100)]
arm64: dts: rockchip: add EEPROM found on RK3399 Puma Haikou
The Haikou carrierboard has an EEPROM on LVDS_BLC_CLK/DAT which are
signals that can carry either I2C or be used as HPD for eDP0/1.
Only eDP0 is routed from RK3399 Puma SoM but only exposed on Haikou
through the Video Connector, a fake PCIe connector. So to be able to use
eDP one would need to use a Device Tree overlay. Therefore, let's
default to having an EEPROM in Haikou carrierboard DTS.
Quentin Schulz [Tue, 18 Feb 2025 11:49:16 +0000 (12:49 +0100)]
arm64: dts: rockchip: enable I2S0 in Haikou carrierboard, not Puma DTSI
I2S0 is routed to the Q7 golden fingers and, on Haikou carrierboard, to
an I2S codec. Nothing aside from signal routing is done on the SoM,
therefore it's the duty of the carrierboard to enable I2S0 whenever an
I2S codec is present.
Such is the case of the Haikou carrierboard, therefore let's migrate the
enabling of this controller to the carrierboard DTS instead of the SoM
DTSI.
Quentin Schulz [Tue, 18 Feb 2025 11:49:14 +0000 (12:49 +0100)]
arm64: dts: rockchip: move I2C6 from Haikou carrierboard to Puma DTSI
I2C6 is not exposed on Q7 golden fingers which is for routing signals to
the carrierboard but on Q7 Camera connector, for routing signals to an
additional adapter (e.g. Q7 Camera Demo adapter).
Therefore, let's move the modification of I2C6 bus to Puma DTSI.
Quentin Schulz [Tue, 18 Feb 2025 11:49:12 +0000 (12:49 +0100)]
arm64: dts: rockchip: enable UART5 on RK3588 Tiger Haikou
In its default configuration (SW2 on "UART1"), UART5 is exposed on the
DB9 RS232/RS485 connector. While the same signals are also exposed on
Q7_GPIO5 and Q7_GPIO6, a GPIO header, and thus could be used for other
purposes, RK3399 Puma Haikou and PX30 Ringneck Haikou do enable the UART
controller exposed on the DB9 connector, so let's keep consistency
across our modules and enable it on RK3588 Tiger Haikou by default too.
Add a comment while at it to explicit where this controller is routed
to.
Quentin Schulz [Fri, 21 Feb 2025 14:04:37 +0000 (15:04 +0100)]
arm64: dts: rockchip: add overlay for RK3399 Puma Haikou Video Demo adapter
This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/) for the Haikou
devkit with RK3399 Puma SoM.
The Video Demo adapter is an adapter connected to the fake PCIe slot
labeled "Video Connector" on the Haikou devkit.
Its main feature is a Leadtek DSI-display with touchscreen and a camera
(that is not supported yet because the expected clock rate by the driver
cannot be exactly reached by the clock driver). To drive these
components a number of additional regulators are grouped on the adapter
as well as a PCA9670 gpio-expander to provide the needed additional
gpio-lines.
Quentin Schulz [Fri, 21 Feb 2025 14:04:36 +0000 (15:04 +0100)]
arm64: dts: rockchip: add overlay for PX30 Ringneck Haikou Video Demo adapter
This adds support for the video-demo-adapter DEVKIT ADDON CAM-TS-A01
(https://embedded.cherry.de/product/development-kit/) for the Haikou
devkit with PX30 Ringneck SoM.
The Video Demo adapter is an adapter connected to the fake PCIe slot
labeled "Video Connector" on the Haikou devkit.
Itss main feature is a Leadtek DSI-display with touchscreen and a camera
(that is not supported yet because the expected clock rate by the driver
cannot be exactly reached by the clock driver). To drive these
components a number of additional regulators are grouped on the adapter
as well as a PCA9670 gpio-expander to provide the needed additional
gpio-lines.
Quentin Schulz [Fri, 21 Feb 2025 14:04:35 +0000 (15:04 +0100)]
arm64: dts: rockchip: add support for HAIKOU-LVDS-9904379 adapter for PX30 Ringneck
The HAIKOU-LVDS-9904379 adapter is an adapter for PX30 Ringneck with the
Haikou carrierboard. It is to be inserted in the fake PCIe slot labelled
Video Connector.
This adapter expects an Admatec 9904379 1024x600 LVDS display with
backlight and touchscreen. An EEPROM is also found on the adapter.
This adds support for this adapter on PX30 Ringneck when inserted in
Haikou carrierboard.
Quentin Schulz [Tue, 11 Feb 2025 14:02:53 +0000 (15:02 +0100)]
arm64: dts: rockchip: minimal support for Pre-ICT tester adapter for RK3588 Jaguar
The Pre-ICT tester adapter connects to RK3588 Jaguar SBC through its
proprietary Mezzanine connector.
It exposes a PCIe Gen2 1x M.2 connector and two proprietary camera
connectors. Support for the latter will come once the rest of the camera
stack is supported.
Additionally, the adapter loops some GPIOs together as well as route
some GPIOs to power rails.
This adapter is used for manufacturing RK3588 Jaguar to be able to test
the Mezzanine connector is properly soldered.
Quentin Schulz [Tue, 11 Feb 2025 14:02:52 +0000 (15:02 +0100)]
arm64: dts: rockchip: add overlay tests for Rock 5B PCIe overlays
According to commit 40658534756f ("arm64: dts: rockchip: Add rock5b
overlays for PCIe endpoint mode"), Rock 5B can operate in PCIe endpoint
mode. For that to work, the rk3588-rock-5b-pcie-ep.dtbo overlay needs to
be applied on Rock 5B base Device Tree. If that Rock 5B is connected to
another Rock 5B, the latter needs to apply the
rk3588-rock-5b-pcie-srns.dtbo overlay.
In order to make sure the overlays are still valid in the future, let's
add a validation test by applying the overlays on top of the main base
at build time.
Quentin Schulz [Tue, 11 Feb 2025 14:02:51 +0000 (15:02 +0100)]
arm64: dts: rockchip: add overlay test for Edgeble NCM6A/NCM6B
The Edgeble NCM6A/NCM6B can have WiFi modules connected and this is
handled via an overlay (commit 951d6aaa37fe ("arm64: dts: rockchip: Add
Edgeble NCM6A WiFi6 Overlay")).
Despite the name of the overlay, it applies to both NCM6A and NCM6B[1].
In order to make sure the overlay is still valid in the future, let's
add a validation test by applying the overlay on top of the main bases
at build time.
Quentin Schulz [Tue, 11 Feb 2025 14:02:50 +0000 (15:02 +0100)]
arm64: dts: rockchip: add overlay test for WolfVision PF5
The WolfVision PF5 can have a PF5 Visualizer display and PF5 IO Expander
board connected to it. Therefore, let's generate an overlay test so the
application of the two overlays are validated against the base DTB.
Dragan Simic [Mon, 10 Feb 2025 20:17:00 +0000 (21:17 +0100)]
arm64: dts: rockchip: linewrap gmac assigned-clocks on Quartz64 Model A/B files a bit
Going over the 80-column width limit, and using all 100 columns, is intended
for improving code readability. This wasn't the case in a few places in the
Quartz64 Model A/B board dts files, so let's reflow them a bit, to both obey
the 80-column limit and make them a bit more readable.
No intended functional changes are introduced by these changes.
Chris Morgan [Thu, 30 Jan 2025 18:10:04 +0000 (12:10 -0600)]
arm64: dts: rockchip: remove rk3588 optee node
Remove Optee node from rk3588 devicetree. When Optee is present and
used the node will be added automatically by U-Boot when
CONFIG_OPTEE_LIB=y and CONFIG_SPL_ATF_NO_PLATFORM_PARAM is not set.
When Optee is not present or used, the node will trigger a probe
that generates a (harmless) message on the kernel log.
arm64: dts: rockchip: Add PHY node for HDMI1 TX port on RK3588
In preparation to enable the second HDMI output port found on RK3588
SoC, add the related PHY node. This requires a GRF, hence add the
dependent node as well.
Junhao Xie [Tue, 14 Jan 2025 00:14:11 +0000 (08:14 +0800)]
arm64: dts: rockchip: add dts for Ariaboard Photonicat RK3568
Add dts for Ariaboard Photonicat RK3568.
Partially based on downstream board dts. [1]
Working IO:
Debug UART
SDIO QCA9377 WiFi and Bluetooth
M.2 E-Key PCIe WiFi and Bluetooth
M.2 B-Key USB Modem WWAN
Ethernet WAN Port
MicroSD Card slot
eMMC
HDMI Output
Mali GPU
USB Type-A
Not working IO:
Ethernet LAN Port (Lack of SGMII support)
Power management MCU on UART4 (Driver pending)
Not working IO in MCU:
Battery voltage sensor
Board temperature sensor
Hardware Power-off
Hardware Watchdog
Network status LED
Real-time clock
USB Charger voltage sensor
About onboard power management MCU:
A heartbeat must be sent to the MCU within 60 seconds,
otherwise the MCU will restart the system.
When powering off, a shutdown command needs to be sent to the MCU.
When the power button is long pressed, the MCU will send a shutdown
command to the system. If system does not shutdown within 60 seconds,
the power will be turned off directly.
MCU only provides voltage for charger and battery.
Manufacturer removed RK8xx PMIC.
Alexey Charkov [Tue, 4 Feb 2025 09:02:28 +0000 (13:02 +0400)]
arm64: dts: rockchip: switch Rock 5C to PMIC-based TSHUT reset
Radxa Rock 5C supports both CRU-based (default) and PMIC-based reset
upon thermal runaway conditions. The former resets the SoC by internally
poking the CRU from TSADC, while the latter power-cycles the whole board
by pulling the PMIC reset line low in case of uncontrolled overheating.
Switch to a PMIC-based reset, as the more 'thorough' of the two.
Tested by temporarily setting rockchip,hw-tshut-temp to 65C to simulate
overheating - this causes the board to reset when any of the on-chip
temperature sensors surpasses the tshut temperature.
Damon Ding [Thu, 6 Feb 2025 03:03:30 +0000 (11:03 +0800)]
arm64: dts: rockchip: Fix label name of hdptxphy for RK3588
The hdptxphy is a combo transmit-PHY for HDMI2.1 TMDS Link, FRL Link, DP
and eDP Link. Therefore, it is better to name it hdptxphy0 other than
hdptxphy_hdmi0, which will be referenced by both hdmi0 and edp0 nodes.
arm64: dts: rockchip: Add HDMI0 PHY PLL clock source to VOP2 on RK3588
VOP2 on RK3588 is able to use the HDMI PHY PLL as an alternative and
more accurate pixel clock source to improve handling of display modes up
to 4K@60Hz on video ports 0, 1 and 2.
For now only HDMI0 output is supported, hence add the related PLL clock.
arm64: dts: rockchip: Enable HDMI0 PHY clk provider on RK3588
Since commit c4b09c562086 ("phy: phy-rockchip-samsung-hdptx: Add clock
provider support"), the HDMI PHY PLL can be used as an alternative and
more accurate pixel clock source for VOP2 to improve display modes
handling on RK3588 SoC.
Add the missing #clock-cells property to allow using the clock provider
functionality of HDMI0 PHY.
Dragan Simic [Wed, 8 Jan 2025 04:26:45 +0000 (05:26 +0100)]
arm64: dts: rockchip: Use "dma-noncoherent" in base RK3588 SoC dtsi
The preferred way to denote hardware with non-coherent DMA is to use the
"dma-noncoherent" DT property, at both the GIC redistributor and the GIC ITS
levels, [1] instead of relying on the compatibles to handle hardware errata,
in this case the Rockchip 3588001 errata. [2]
Let's have the preferred way employed in the base Rockchip RK3588 SoC dtsi,
which also goes along with adding initial support for the Rockchip RK3582 SoC
variant, with its separate compatible. [2][3]
Dragan Simic [Mon, 2 Dec 2024 14:44:06 +0000 (15:44 +0100)]
arm64: dts: rockchip: Describe why is HWRNG disabled in RK356x base dtsi
Despite the presence of the hardware random number generator (HWRNG) in the
different Rockchip RK356x SoC variants, it remains disabled for the RK3566
SoC because testing showed [1] that it produces unacceptably low quality of
random data, for some yet unknown reason. The HWRNG is enabled for the RK3568
SoC, on which the testing showed good quality of the generated random data.
To avoid possible confusion in the future, [2] let's have this described
briefly in the RK356x base SoC dtsi.
Alexey Charkov [Mon, 20 Jan 2025 19:22:47 +0000 (23:22 +0400)]
arm64: dts: rockchip: Enable automatic fan control on Radxa Rock 5C
Add the necessary cooling map to enable the kernel's thermal subsystem
to manage the fan speed automatically depending on the overall SoC
package temperature on Radxa Rock 5C
Alexey Charkov [Mon, 20 Jan 2025 19:22:46 +0000 (23:22 +0400)]
arm64: dts: rockchip: Add finer-grained PWM states for the fan on Rock 5C
Radxa Heatsink 6540B, which is the official cooling accessory for the
Rock 5C board, includes a small 5V fan, which in my testing spins up
reliably at a PWM setting of 24 (out of 255). It is also quite loud
at the current minimum setting of 64, and noticeably less so at 24.
Introduce two intermediate PWM states at the lower end of the fan's
operating range to enable better balance between noise and cooling.
Note further that, in my testing, having the fan run at 44 is enough
to keep the system from thermal throttling with sustained 100% load
on its 8 CPU cores (in 22C ambient temperature and no case)
Linus Torvalds [Sun, 2 Feb 2025 18:49:13 +0000 (10:49 -0800)]
Merge tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown:
- Fix regression that affinitized forked child in one-shot mode.
- Harden one-shot mode against hotplug online/offline
- Enable RAPL SysWatt column by default
- Add initial PTL, CWF platform support
- Harden initial PMT code in response to early use
- Enable first built-in PMT counter: CWF c1e residency
- Refuse to run on unsupported platforms without --force, to encourage
updating to a version that supports the system, and to avoid
no-so-useful measurement results
* tag 'turbostat-2025.02.02' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (25 commits)
tools/power turbostat: version 2025.02.02
tools/power turbostat: Add CPU%c1e BIC for CWF
tools/power turbostat: Harden one-shot mode against cpu offline
tools/power turbostat: Fix forked child affinity regression
tools/power turbostat: Add tcore clock PMT type
tools/power turbostat: version 2025.01.14
tools/power turbostat: Allow adding PMT counters directly by sysfs path
tools/power turbostat: Allow mapping multiple PMT files with the same GUID
tools/power turbostat: Add PMT directory iterator helper
tools/power turbostat: Extend PMT identification with a sequence number
tools/power turbostat: Return default value for unmapped PMT domains
tools/power turbostat: Check for non-zero value when MSR probing
tools/power turbostat: Enhance turbostat self-performance visibility
tools/power turbostat: Add fixed RAPL PSYS divisor for SPR
tools/power turbostat: Fix PMT mmaped file size rounding
tools/power turbostat: Remove SysWatt from DISABLED_BY_DEFAULT
tools/power turbostat: Add an NMI column
tools/power turbostat: add Busy% to "show idle"
tools/power turbostat: Introduce --force parameter
tools/power turbostat: Improve --help output
...
Linus Torvalds [Sun, 2 Feb 2025 18:40:27 +0000 (10:40 -0800)]
Merge tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from John Paul Adrian Glaubitz:
"Fixes and improvements for sh:
- replace seq_printf() with the more efficient
seq_put_decimal_ull_width() to increase performance when stress
reading /proc/interrupts (David Wang)
- migrate sh to the generic rule for built-in DTB to help avoid race
conditions during parallel builds which can occur because Kbuild
decends into arch/*/boot/dts twice (Masahiro Yamada)
- replace select with imply in the board Kconfig for enabling
hardware with complex dependencies. This addresses warnings which
were reported by the kernel test robot (Geert Uytterhoeven)"
* tag 'sh-for-v6.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: boards: Use imply to enable hardware with complex dependencies
sh: Migrate to the generic rule for built-in DTB
sh: irq: Use seq_put_decimal_ull_width() for decimal values
Len Brown [Sun, 2 Feb 2025 16:43:02 +0000 (10:43 -0600)]
tools/power turbostat: version 2025.02.02
Summary of Changes since 2024.11.30:
Fix regression in 2023.11.07 that affinitized forked child
in one-shot mode.
Harden one-shot mode against hotplug online/offline
Enable RAPL SysWatt column by default.
Add initial PTL, CWF platform support.
Harden initial PMT code in response to early use.
Enable first built-in PMT counter: CWF c1e residency
Refuse to run on unsupported platforms without --force,
to encourage updating to a version that supports the system,
and to avoid no-so-useful measurement results.
Linus Torvalds [Sat, 1 Feb 2025 23:07:56 +0000 (15:07 -0800)]
Merge tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc vfs cleanups from Al Viro:
"Two unrelated patches - one is a removal of long-obsolete include in
overlayfs (it used to need fs/internal.h, but the extern it wanted has
been moved back to include/linux/namei.h) and another introduces
convenience helper constructing struct qstr by a NUL-terminated
string"
* tag 'pull-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
add a string-to-qstr constructor
fs/overlayfs/namei.c: get rid of include ../internal.h
Linus Torvalds [Sat, 1 Feb 2025 19:30:41 +0000 (11:30 -0800)]
Merge tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- various updates for special file handling: symlink handling,
support for creating sockets, cleanups, new mount options (e.g. to
allow disabling using reparse points for them, and to allow
overriding the way symlinks are saved), and fixes to error paths
- fix for kerberos mounts (allow IAKerb)
- SMB1 fix for stat and for setting SACL (auditing)
- fix an incorrect error code mapping
- cleanups"
* tag 'v6.14-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: (21 commits)
cifs: Fix parsing native symlinks directory/file type
cifs: update internal version number
cifs: Add support for creating WSL-style symlinks
smb3: add support for IAKerb
cifs: Fix struct FILE_ALL_INFO
cifs: Add support for creating NFS-style symlinks
cifs: Add support for creating native Windows sockets
cifs: Add mount option -o reparse=none
cifs: Add mount option -o symlink= for choosing symlink create type
cifs: Fix creating and resolving absolute NT-style symlinks
cifs: Simplify reparse point check in cifs_query_path_info() function
cifs: Remove symlink member from cifs_open_info_data union
cifs: Update description about ACL permissions
cifs: Rename struct reparse_posix_data to reparse_nfs_data_buffer and move to common/smb2pdu.h
cifs: Remove struct reparse_posix_data from struct cifs_open_info_data
cifs: Remove unicode parameter from parse_reparse_point() function
cifs: Fix getting and setting SACLs over SMB1
cifs: Remove intermediate object of failed create SFU call
cifs: Validate EAs for WSL reparse points
cifs: Change translation of STATUS_PRIVILEGE_NOT_HELD to -EPERM
...
Linus Torvalds [Sat, 1 Feb 2025 18:04:29 +0000 (10:04 -0800)]
Merge tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull debugfs fix from Greg KH:
"Here is a single debugfs fix from Al to resolve a reported regression
in the driver-core tree. It has been reported to fix the issue"
* tag 'driver-core-6.14-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Fix the missing initializations in __debugfs_file_get()
Linus Torvalds [Sat, 1 Feb 2025 17:49:20 +0000 (09:49 -0800)]
Merge tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"21 hotfixes. 8 are cc:stable and the remainder address post-6.13
issues. 13 are for MM and 8 are for non-MM.
All are singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-02-01-03-56' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (21 commits)
MAINTAINERS: include linux-mm for xarray maintenance
revert "xarray: port tests to kunit"
MAINTAINERS: add lib/test_xarray.c
mailmap, MAINTAINERS, docs: update Carlos's email address
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
mm: gup: fix infinite loop within __get_longterm_locked
mm, swap: fix reclaim offset calculation error during allocation
.mailmap: update email address for Christopher Obbard
kfence: skip __GFP_THISNODE allocations on NUMA systems
nilfs2: fix possible int overflows in nilfs_fiemap()
mm: compaction: use the proper flag to determine watermarks
kernel: be more careful about dup_mmap() failures and uprobe registering
mm/fake-numa: handle cases with no SRAT info
mm: kmemleak: fix upper boundary check for physical address objects
mailmap: add an entry for Hamza Mahfooz
MAINTAINERS: mailmap: update Yosry Ahmed's email address
scripts/gdb: fix aarch64 userspace detection in get_current_task
mm/vmscan: accumulate nr_demoted for accurate demotion statistics
ocfs2: fix incorrect CPU endianness conversion causing mount failure
mm/zsmalloc: add __maybe_unused attribute for is_first_zpdesc()
...
Linus Torvalds [Sat, 1 Feb 2025 17:15:01 +0000 (09:15 -0800)]
Merge tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"A revert for a regression in the uvcvideo driver"
* tag 'media/v6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
Revert "media: uvcvideo: Require entities to have a non-zero unique ID"
Update .mailmap to reflect my new (and final) primary email address,
carlos.bilbao@kernel.org. Also update contact information in files
Documentation/translations/sp_SP/index.rst and MAINTAINERS.
Link: https://lkml.kernel.org/r/20250130012248.1196208-1-carlos.bilbao@kernel.org Signed-off-by: Carlos Bilbao <carlos.bilbao@kernel.org> Cc: Carlos Bilbao <bilbao@vt.edu> Cc: Jonathan Corbet <corbet@lwn.net> Cc: Mattew Wilcox <willy@infradead.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
mm/hugetlb: fix hugepage allocation for interleaved memory nodes
gather_bootmem_prealloc() assumes the start nid as 0 and size as
num_node_state(N_MEMORY). That means in case if memory attached numa
nodes are interleaved, then gather_bootmem_prealloc_parallel() will fail
to scan few of these nodes.
Since memory attached numa nodes can be interleaved in any fashion, hence
ensure that the current code checks for all numa node ids
(.size = nr_node_ids). Let's still keep max_threads as N_MEMORY, so that
it can distributes all nr_node_ids among the these many no. threads.
Zhaoyang Huang [Tue, 21 Jan 2025 02:01:59 +0000 (10:01 +0800)]
mm: gup: fix infinite loop within __get_longterm_locked
We can run into an infinite loop in __get_longterm_locked() when
collect_longterm_unpinnable_folios() finds only folios that are isolated
from the LRU or were never added to the LRU. This can happen when all
folios to be pinned are never added to the LRU, for example when
vm_ops->fault allocated pages using cma_alloc() and never added them to
the LRU.
Fix it by simply taking a look at the list in the single caller, to see if
anything was added.
[zhaoyang.huang@unisoc.com: move definition of local] Link: https://lkml.kernel.org/r/20250122012604.3654667-1-zhaoyang.huang@unisoc.com Link: https://lkml.kernel.org/r/20250121020159.3636477-1-zhaoyang.huang@unisoc.com Fixes: 67e139b02d99 ("mm/gup.c: refactor check_and_migrate_movable_pages()") Signed-off-by: Zhaoyang Huang <zhaoyang.huang@unisoc.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Reviewed-by: David Hildenbrand <david@redhat.com> Suggested-by: David Hildenbrand <david@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Aijun Sun <aijun.sun@unisoc.com> Cc: Alistair Popple <apopple@nvidia.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Kairui Song [Thu, 30 Jan 2025 11:51:31 +0000 (19:51 +0800)]
mm, swap: fix reclaim offset calculation error during allocation
There is a code error that will cause the swap entry allocator to reclaim
and check the whole cluster with an unexpected tail offset instead of the
part that needs to be reclaimed. This may cause corruption of the swap
map, so fix it.
Link: https://lkml.kernel.org/r/20250130115131.37777-1-ryncsn@gmail.com Fixes: 3b644773eefd ("mm, swap: reduce contention on device lock") Signed-off-by: Kairui Song <kasong@tencent.com> Cc: Chris Li <chrisl@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
projects / thirdparty / linux.git / log
