The definition of CS42L42_ADC_PDN_MASK was incorrectly defined
as the HP_PDN bit.
Fixes: 2c394ca79604 ("ASoC: Add support for CS42L42 codec") Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20210616135604.19363-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Fixes: 1c28799257bc ("iio: light: isl29501: Add support for the ISL29501 ToF sensor.") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Mathieu Othacehe <m.othacehe@gmail.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210613152301.571002-9-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a potential
kernel data leak, making for a less minimal fix.
Fixes: 55707294c4eb ("iio: light: Add support for vishay vcnl4035") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Parthiban Nallathambi <pn@denx.de> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210613152301.571002-8-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit 2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
The B_SESS_VLD_WAKEUP_EN bit 6 was added by a mistake in a previous
commit. This bit corresponds to B_SESS_END_WAKEUP_EN, which we don't use.
The B_VBUS_VLD_WAKEUP_EN doesn't exist at all and B_SESS_VLD_WAKEUP_EN
needs to be in place of it. We don't utilize B-sensors in the driver,
so it never was a problem, nevertheless let's correct the definition of
the bits.
Fixes: 35192007d28d ("usb: phy: tegra: Support waking up from a low power mode") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20210613145936.9902-2-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some devices need an extra delay after losing VBUS, otherwise VBUS may
be detected as active at suspend time, preventing the PHY's suspension
by the VBUS detection sensor. This problem was found on Asus Transformer
TF700T (Tegra30) tablet device, where the USB PHY wakes up immediately
from suspend because VBUS sensor continues to detect VBUS as active after
disconnection. We need to poll the PHY's VBUS wakeup status until it's
deasserted before suspending PHY in order to fix this minor trouble.
Fixes: 35192007d28d ("usb: phy: tegra: Support waking up from a low power mode") Reported-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Tested-by: Maxim Schwalm <maxim.schwalm@gmail.com> # Asus TF700T Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Link: https://lore.kernel.org/r/20210613145936.9902-1-digetx@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Driver code call 'devm_of_pci_get_host_bridge_resources'
to get resources and properly fill 'bridge->windows' and
'bridge->dma_ranges'. After parsing the ranges and store
as resources, at the end it makes a call to pci function
'pci_add_resource_offset' to set the offset for the
memory resource. To calculate offset, resource start address
subtracts pci address of the range. MT7621 does not need
any offset for the memory resource. Moreover, setting an
offset got into 'WARN_ON' calls from pci devices driver code.
Until now memory range pci_addr was being '0x00000000' and
res->start is '0x60000000' but becase pci controller driver
was manually setting resources and adding them using pci function
'pci_add_resource' where a zero is passed as offset, things
was properly working. Since PCI_IOBASE is defined now for
ralink we don't set nothing manually anymore so we have to
properly fix PCI address for this range to make things work
and the new pci address must be set to '0x60000000'. Doing
in this way the subtract result obtain zero as offset
and pci device driver code properly works.
There is a leak in rtl8712 driver.
The problem was in non-freed adapter data if
firmware load failed.
This leak can be reproduced with this code:
https://syzkaller.appspot.com/text?tag=ReproC&x=16612f02d00000,
Autoload must fail (to not hit memory leak reported by syzkaller)
There are 2 possible ways how rtl871x_load_fw_cb() and
r871xu_dev_remove() can be called (in case of fw load error).
1st case:
r871xu_dev_remove() then rtl871x_load_fw_cb()
In this case r871xu_dev_remove() will wait for
completion and then will jump to the end, because
rtl871x_load_fw_cb() set intfdata to NULL:
if (pnetdev) {
struct _adapter *padapter = netdev_priv(pnetdev);
/* never exit with a firmware callback pending */
wait_for_completion(&padapter->rtl8712_fw_ready);
pnetdev = usb_get_intfdata(pusb_intf);
usb_set_intfdata(pusb_intf, NULL);
if (!pnetdev)
goto firmware_load_fail;
... clean up code here ...
}
2nd case:
rtl871x_load_fw_cb() then r871xu_dev_remove()
In this case pnetdev (from code snippet above) will
be zero (because rtl871x_load_fw_cb() set it to NULL)
And clean up code won't be executed again.
So, in all cases we need to free adapted data in rtl871x_load_fw_cb(),
because disconnect function cannot take care of it. And there won't be
any race conditions, because complete() call happens after setting
intfdata to NULL.
In previous patch I moved out free_netdev() from r8712_free_drv_sw()
and that's why now it's possible to free adapter data and then call
complete.
Previous error handling path was unique for all
possible errors and there was unnecessary branching.
Also, one step for freeing drv_sw was missing. All
these problems was fixed by restructuring error
handling path.
Also, moved out free_netdev() from r8712_free_drv_sw() for
correct error handling.
There needs to be a check to verify that we don't read beyond the end
of "buf". This function is called from do_rx(). The "buf" is the USB
transfer_buffer and "len" is "urb->actual_length".
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because the holes would
necessitate the addition of an explict memset(), to avoid a kernel
data leak, making for a less minimal fix.
Found during an audit of all callers of iio_push_to_buffers_with_timestamp()
Fixes: 8fe78d5261e7 ("iio: vcnl4000: Add buffer support for VCNL4010/20.") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Mathieu Othacehe <m.othacehe@gmail.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210613152301.571002-7-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here an explicit structure is not used, because this buffer is used in
a non-trivial way for data repacking.
Fixes: 121354b2eceb ("iio: magnetometer: Add driver support for PNI RM3100") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Song Qiang <songqiang1304521@gmail.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210613152301.571002-6-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Fixes: f214ff521fb1 ("iio: ti-ads8688: Update buffer allocation for timestamps") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210613152301.571002-5-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Add a comment on why the buffer is the size it is as not immediately
obvious.
Found during an audit of all calls of this function.
Fixes: 6dd112b9f85e ("iio: adc: mxs-lradc: Add support for ADC driver") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Andreas Klinger <ak@it-klinger.de> Reviewed-by: Nuno Sá <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210613152301.571002-4-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When one parameter of a parameterised test failed, its failure would be
propagated to the overall test, but not to the suite result (unless it
was the last parameter).
This is because test_case->success was being reset to the test->success
result after each parameter was used, so a failing test's result would
be overwritten by a non-failing result. The overall test result was
handled in a third variable, test_result, but this was discarded after
the status line was printed.
Instead, just propagate the result after each parameter run.
Signed-off-by: David Gow <davidgow@google.com> Fixes: fadb08e7c750 ("kunit: Support for Parameterized Testing") Reviewed-by: Marco Elver <elver@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the raw NAND world, ECC engines increment ecc_stats and the final
caller is responsible for returning -EBADMSG if the verification
failed.
In the SPI-NAND world it was a bit different until now because there was
only one possible ECC engine: the on-die one. Indeed, the
spinand_mtd_read() call was incrementing the ecc_stats counters
depending on the outcome of spinand_check_ecc_status() directly.
So now let's split the logic like this:
- spinand_check_ecc_status() is specific to the SPI-NAND on-die engine
and is kept very simple: it just returns the ECC status (bonus point:
the content of this helper can be overloaded).
- spinand_ondie_ecc_finish_io_req() is the caller of
spinand_check_ecc_status() and will increment the counters and
eventually return -EBADMSG.
- spinand_mtd_read() is not tied to the on-die ECC implementation and
should be able to handle results coming from other ECC engines: it has
the responsibility of returning the maximum number of bitflips which
happened during the entire operation as this is the only helper that
is aware that several pages may be read in a row.
Fixes: 945845b54c9c ("mtd: spinand: Instantiate a SPI-NAND on-die ECC engine") Reported-by: YouChing Lin <ycllin@mxic.com.tw> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: YouChing Lin <ycllin@mxic.com.tw> Link: https://lore.kernel.org/linux-mtd/20210527084345.208215-1-miquel.raynal@bootlin.com Signed-off-by: Sasha Levin <sashal@kernel.org>
We should not dereference ->dual_link_port if it is NULL and lane bonding
is requested. For this reason move lane bonding configuration happen
inside the block where ->dual_link_port != NULL.
Fixes: 54509f5005ca ("thunderbolt: Add KUnit tests for path walking") Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Every time the hub signals a reset while we (device) are hsotg->connected,
dwc2_hsotg_core_init_disconnected() is called, which in turn calls
dwc2_hs_phy_init().
GUSBCFG.USBTrdTim is cleared upon Core Soft Reset, so if
hsotg->params.phy_utmi_width is 8-bit, the value of GUSBCFG.USBTrdTim (the
default one: 0x5, corresponding to 16-bit) is always different from
hsotg->params.phy_utmi_width, thus dwc2_core_reset() is called every
time (usbcfg != usbcfg_old), which causes 2 issues:
1) The call to dwc2_core_reset() does another reset 300us after the initial
Chirp K of the first reset (which should last at least Tuch = 1ms), and
messes up the High-speed Detection Handshake: both hub and device drive
current into the D+ and D- lines at the same time.
2) GUSBCFG.USBTrdTim is cleared by the second reset, so its value is always
the default one (0x5).
Setting GUSBCFG.USBTrdTim after the potential call to dwc2_core_reset()
fixes both issues. It is now set even when select_phy is false because the
cost of the Core Soft Reset is removed.
FunctionFS device structure 'struct ffs_dev' and driver data structure
'struct ffs_data' are bound to each other with cross-reference pointers
'ffs_data->private_data' and 'ffs_dev->ffs_data'. While the first one
is supposed to be valid through the whole life of 'struct ffs_data'
(and while 'struct ffs_dev' exists non-freed), the second one is cleared
in 'ffs_closed()' (called from 'ffs_data_reset()' or the last
'ffs_data_put()'). This can be called several times, alternating in
different order with 'ffs_free_inst()', that, if possible, clears
the other cross-reference.
As a result, different cases of these calls order may leave stale
cross-reference pointers, used when the pointed structure is already
freed. Even if it occasionally doesn't cause kernel crash, this error
is reported by KASAN-enabled kernel configuration.
For example, the case [last 'ffs_data_put()' - 'ffs_free_inst()'] was
fixed by commit cdafb6d8b8da ("usb: gadget: f_fs: Fix use-after-free in
ffs_free_inst").
The other case ['ffs_data_reset()' - 'ffs_free_inst()' - 'ffs_data_put()']
now causes KASAN reported error [1], when 'ffs_data_reset()' clears
'ffs_dev->ffs_data', then 'ffs_free_inst()' frees the 'struct ffs_dev',
but can't clear 'ffs_data->private_data', which is then accessed
in 'ffs_closed()' called from 'ffs_data_put()'. This happens since
'ffs_dev->ffs_data' reference is cleared too early.
Moreover, one more use case, when 'ffs_free_inst()' is called immediately
after mounting FunctionFS device (that is before the descriptors are
written and 'ffs_ready()' is called), and then 'ffs_data_reset()'
or 'ffs_data_put()' is called from accessing "ep0" file or unmounting
the device. This causes KASAN error report like [2], since
'ffs_dev->ffs_data' is not yet set when 'ffs_free_inst()' can't properly
clear 'ffs_data->private_data', that is later accessed to freed structure.
Fix these (and may be other) cases of stale pointers access by moving
setting and clearing of the mentioned cross-references to the single
places, setting both of them when 'struct ffs_data' is created and
bound to 'struct ffs_dev', and clearing both of them when one of the
structures is destroyed. It seems convenient to make this pointer
initialization and structures binding in 'ffs_acquire_dev()' and
make pointers clearing in 'ffs_release_dev()'. This required some
changes in these functions parameters and return types.
Also, 'ffs_release_dev()' calling requires some cleanup, fixing minor
issues, like (1) 'ffs_release_dev()' is not called if 'ffs_free_inst()'
is called without unmounting the device, and "release_dev" callback
is not called at all, or (2) "release_dev" callback is called before
"ffs_closed" callback on unmounting, which seems to be not correctly
nested with "acquire_dev" and "ffs_ready" callbacks.
Make this cleanup togther with other mentioned 'ffs_release_dev()' changes.
If an error occurs after a successful 'of_iomap()' call, it must be undone
by a corresponding 'iounmap()' call, as already done in the remove
function.
While at it, remove the useless initialization of 'ret' at the beginning of
the function.
The device checking error should be a jump to pm_runtime_put_autosuspend()
as done before returning value.
Fixes: 867f8d18df4f ('ASoC: rt5682: fix getting the wrong device id when the suspend_stress_test') Reviewed-by: Bard Liao <bard.liao@intel.com> Signed-off-by: Oder Chiou <oder_chiou@realtek.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210607222239.582139-13-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
The intent of the status check on resume was to verify if a SoundWire
peripheral reported ATTACHED before waiting for the initialization to
complete. This is required to avoid timeouts that will happen with
'ghost' devices that are exposed in the platform firmware but are not
populated in hardware.
Unfortunately we used 'hw_init' instead of 'first_hw_init'. Due to
another error, the resume operation never timed out, but the volume
settings were not properly restored.
This patch renames the status flag to 'first_hw_init' for consistency
with other drivers.
Some pseudo-filesystems do not have an explicit splice fops since adding
commit 36e2c7421f02 ("fs: don't allow splice read/write without explicit ops"),
and now will reject attempts to use splice() in those filesystem paths.
APPLDATA_BASE should depend on PROC_SYSCTL instead of PROC_FS.
Building with PROC_FS but not PROC_SYSCTL causes a build error,
since appldata_base.c uses data and APIs from fs/proc/proc_sysctl.c.
arch/s390/appldata/appldata_base.o: in function `appldata_generic_handler':
appldata_base.c:(.text+0x192): undefined reference to `sysctl_vals'
In commit b02002cc4c0f ("s390/pci: Implement ioremap_wc/prot() with
MIO") we implemented both ioremap_wc() and ioremap_prot() however until
now we had not set HAVE_IOREMAP_PROT in Kconfig, do so now.
This also requires implementing pte_pgprot() as this is used in the
generic_access_phys() code enabled by CONFIG_HAVE_IOREMAP_PROT. As with
ioremap_wc() we need to take the MMIO Write Back bit index into account.
Moreover since the pgprot value returned from pte_pgprot() is to be used
for mappings into kernel address space we must make sure that it uses
appropriate kernel page table protection bits. In particular a pgprot
value originally coming from userspace could have the _PAGE_PROTECT
bit set to enable fault based dirty bit accounting which would then make
the mapping inaccessible when used in kernel address space.
print_iommu_info prints the EFR register and then the decoded list of
features on a separate line:
pci 0000:00:00.2: AMD-Vi: Extended features (0x206d73ef22254ade):
PPR X2APIC NX GT IA GA PC GA_vAPIC
The second line is emitted via 'pr_cont', which causes it to have a
different ('warn') loglevel compared to the previous line ('info').
Commit 9a295ff0ffc9 attempted to rectify this by removing the newline
from the pci_info format string, but this doesn't work, as pci_info
calls implicitly append a newline anyway.
Printing the decoded features on the same line would make it quite long.
Instead, change pci_info() to pr_info() to omit PCI bus location info,
which is also shown in the preceding message. This results in:
pci 0000:00:00.2: AMD-Vi: Found IOMMU cap 0x40
AMD-Vi: Extended features (0x206d73ef22254ade): PPR X2APIC NX GT IA GA PC GA_vAPIC
AMD-Vi: Interrupt remapping enabled
Fixes: 9a295ff0ffc9 ("iommu/amd: Print extended features in one line to fix divergent log levels") Link: https://lore.kernel.org/lkml/alpine.LNX.2.20.13.2104112326460.11104@monopod.intra.ispras.ru Signed-off-by: Alexander Monakov <amonakov@ispras.ru> Cc: Paul Menzel <pmenzel@molgen.mpg.de> Cc: Joerg Roedel <jroedel@suse.de> Cc: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Cc: iommu@lists.linux-foundation.org Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Link: https://lore.kernel.org/r/20210504102220.1793-1-amonakov@ispras.ru Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 1366a3db3dcf ("staging: unisys: visorbus: visorchipset_init clean
up gotos") assigns the initial value -ENODEV to the local variable 'err',
and the first several error branches will return this value after "goto
error". But commit f1f537c2e7f5 ("staging: unisys: visorbus: Consolidate
controlvm channel creation.") overwrites 'err' in the middle of the way.
As a result, some error branches do not successfully return the initial
value -ENODEV of 'err', but return 0.
In addition, when kzalloc() fails, -ENOMEM should be returned instead of
-ENODEV.
On BMCs with lower timer resolution than 1ms, msleep(1) will take
way longer than 1ms, so looping 10k times won't wait for 10s but
significantly longer.
Fix this by using jiffies like the rest of the code.
Fixes: 9f4a8a2d7f9d ("fsi/sbefifo: Add driver for the SBE FIFO") Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Link: https://lore.kernel.org/r/20200724071518.430515-3-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the SBE requests a reset via the down FIFO, that is also the
FIFO we should go and reset ;)
Fixes: 9f4a8a2d7f9d ("fsi/sbefifo: Add driver for the SBE FIFO") Signed-off-by: Joachim Fenkes <FENKES@de.ibm.com> Signed-off-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20200724071518.430515-2-joel@jms.id.au Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the OCC is not initialized and responds as such, the driver
should continue waiting for a valid response until the timeout
expires.
Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Fixes: 7ed98dddb764 ("fsi: Add On-Chip Controller (OCC) driver") Link: https://lore.kernel.org/r/20210209171235.20624-2-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error bits in the FSI2PIB status are only cleared by a reset. So
the driver needs to perform a reset after seeing any of the FSI2PIB
errors, otherwise subsequent operations will also look like failures.
Fixes: 6b293258cded ("fsi: scom: Major overhaul") Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20210329151344.14246-1-eajames@linux.ibm.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the cfam_read and cfam_write functions return the provided
number of bytes given in the count parameter and not the error return
code in variable rc, hence all failures of read/writes are being
silently ignored. Fix this by returning the error code in rc.
Addresses-Coverity: ("Unused value") Fixes: d1dcd6782576 ("fsi: Add cfam char devices") Signed-off-by: Colin Ian King <colin.king@canonical.com> Reviewed-by: Jeremy Kerr <jk@ozlabs.org> Link: https://lore.kernel.org/r/20210603122812.83587-1-colin.king@canonical.com Signed-off-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
During more massive generation of interrupts, the IRQ got stuck,
and the subdevices did not see any new interrupts. That happens
especially at wonky USB supply in combination with ADC reads.
To fix that trigger the IRQ at level low instead of falling edge.
Fixes: 0c81604516af ("mfd: rn5t618: Add IRQ support") Signed-off-by: Andreas Kemnade <andreas@kemnade.info> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 06081646450e ("mfd: mp2629: Add support for mps battery charger") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We set the max_active iSCSI EH works to 1, so all work is going to execute
in order by default. However, userspace can now override this in sysfs. If
max_active > 1, we can end up with the block_work on CPU1 and
iscsi_unblock_session running the unblock_work on CPU2 and the session and
target/device state will end up out of sync with each other.
This adds a flush of the block_work in iscsi_unblock_session.
Link: https://lore.kernel.org/r/20210525181821.7617-17-michael.christie@oracle.com Fixes: 1d726aa6ef57 ("scsi: iscsi: Optimize work queue flush use") Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 0ab710458da1 ("scsi: iscsi: Perform connection failure entirely in
kernel space") has the following regressions/bugs that this patch fixes:
1. It can return cmds to upper layers like dm-multipath where that can
retry them. After they are successful the fs/app can send new I/O to the
same sectors, but we've left the cmds running in FW or in the net layer.
We need to be calling ep_disconnect if userspace is not up.
This patch only fixes the issue for offload drivers. iscsi_tcp will be
fixed in separate commit because it doesn't have a ep_disconnect call.
2. The drivers that implement ep_disconnect expect that it's called before
conn_stop. Besides crashes, if the cleanup_task callout is called before
ep_disconnect it might free up driver/card resources for session1 then they
could be allocated for session2. But because the driver's ep_disconnect is
not called it has not cleaned up the firmware so the card is still using
the resources for the original cmd.
3. The stop_conn_work_fn can run after userspace has done its recovery and
we are happily using the session. We will then end up with various bugs
depending on what is going on at the time.
We may also run stop_conn_work_fn late after userspace has called stop_conn
and ep_disconnect and is now going to call start/bind conn. If
stop_conn_work_fn runs after bind but before start, we would leave the conn
in a unbound but sort of started state where IO might be allowed even
though the drivers have been set in a state where they no longer expect
I/O.
4. Returning -EAGAIN in iscsi_if_destroy_conn if we haven't yet run the in
kernel stop_conn function is breaking userspace. We should have been doing
this for the caller.
Link: https://lore.kernel.org/r/20210525181821.7617-8-michael.christie@oracle.com Fixes: 0ab710458da1 ("scsi: iscsi: Perform connection failure entirely in kernel space") Reviewed-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Subsequent commits allow the kernel to do ep_disconnect. In that case we
will have to get a proper refcount on the ep so one thread does not delete
it from under another.
If the system is not up, we can just fail immediately since iscsid is not
going to ever answer our netlink events. We are already setting the
recovery_tmo to 0, but by passing stop_conn STOP_CONN_TERM we never will
block the session and start the recovery timer, because for that flag
userspace will do the unbind and destroy events which would remove the
devices and wake up and kill the eh.
Since the conn is dead and the system is going dowm this just has us use
STOP_CONN_RECOVER with recovery_tmo=0 so we fail immediately. However, if
the user has set the recovery_tmo=-1 we let the system hang like they
requested since they might have used that setting for specific reasons
(one known reason is for buggy cluster software).
During ep_disconnect we have been doing iscsi_suspend_tx/queue to block new
I/O but every driver except cxgbi and iscsi_tcp can still get I/O from
__iscsi_conn_send_pdu() if we haven't called iscsi_conn_failure() before
ep_disconnect. This could happen if we were terminating the session, and
the logout timed out before it was even sent to libiscsi.
Fix the issue by adding a helper which reverses the bind_conn call that
allows new I/O to be queued. Drivers implementing ep_disconnect can use this
to make sure new I/O is not queued to them when handling the disconnect.
The BusLogic driver has build errors on ia64 due to a name collision (in
the #included FlashPoint.c file). Rename the struct field in struct
sccb_mgr_info from si_flags to si_mflags (manager flags) to mend the build.
This is the first problem. There are 50+ others after this one:
In file included from ../include/uapi/linux/signal.h:6,
from ../include/linux/signal_types.h:10,
from ../include/linux/sched.h:29,
from ../include/linux/hardirq.h:9,
from ../include/linux/interrupt.h:11,
from ../drivers/scsi/BusLogic.c:27:
../arch/ia64/include/uapi/asm/siginfo.h:15:27: error: expected ':', ',', ';', '}' or '__attribute__' before '.' token
15 | #define si_flags _sifields._sigfault._flags
| ^
../drivers/scsi/FlashPoint.c:43:6: note: in expansion of macro 'si_flags'
43 | u16 si_flags;
| ^~~~~~~~
In file included from ../drivers/scsi/BusLogic.c:51:
../drivers/scsi/FlashPoint.c: In function 'FlashPoint_ProbeHostAdapter':
../drivers/scsi/FlashPoint.c:1076:11: error: 'struct sccb_mgr_info' has no member named '_sifields'
1076 | pCardInfo->si_flags = 0x0000;
| ^~
../drivers/scsi/FlashPoint.c:1079:12: error: 'struct sccb_mgr_info' has no member named '_sifields'
Link: https://lore.kernel.org/r/20210529234857.6870-1-rdunlap@infradead.org Fixes: 391e2f25601e ("[SCSI] BusLogic: Port driver to 64-bit.") Cc: "James E.J. Bottomley" <jejb@linux.ibm.com> Cc: "Martin K. Petersen" <martin.petersen@oracle.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Jens Axboe <axboe@kernel.dk> Cc: Hannes Reinecke <hare@suse.de> Cc: Khalid Aziz <khalid.aziz@oracle.com> Cc: Khalid Aziz <khalid@gonehiking.org> Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
fwnode_for_each_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
OTOH, the successful iteration will drop reference count under the hood, no need
to do it twice.
Fixes: 242b81170fb8 ("leds: lp50xx: Add the LP50XX family of the RGB LED driver") Cc: Dan Murphy <dmurphy@ti.com> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
When requesting GPIO line the probe can be deferred.
In such case don't spam logs with an error message.
This can be achieved by switching to dev_err_probe().
Fixes: 5c1d824cda9f ("leds: lm3697: Introduce the lm3697 driver") Cc: Dan Murphy <dmurphy@ti.com> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
device_get_next_child_node() bumps a reference counting of a returned variable.
We have to balance it whenever we return to the caller.
In the older code the same is implied with device_for_each_child_node().
Fixes: 11e1bbc116a7 ("leds: lm36274: Introduce the TI LM36274 LED driver") Fixes: a448fcf19c9c ("leds: lm36274: don't iterate through children since there is only one") Cc: Dan Murphy <dmurphy@ti.com> Cc: Marek Behún <marek.behun@nic.cz> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: bc1b8492c764 ("leds: lm3532: Introduce the lm3532 LED driver") Cc: Dan Murphy <dmurphy@ti.com> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
The clock handling has a few issues:
- when getting second clock fails, the first one left prepared and enabled
- on ->remove() clocks are unprepared and disabled twice
Fix all these by converting to use bulk clock operations since both clocks
are mandatory.
Fixes: c3987cd2bca3 ("leds: lgm: Add LED controller driver for LGM SoC") Cc: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@linux.intel.com> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drop the bogus error code and let of_led_get() to take care about absent
of_node.
Fixes: e389240ad992 ("leds: Add managed API to get a LED from a device driver") Cc: Jean-Jacques Hiblot <jjhiblot@ti.com> Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an error occurs after a successful 'kfifo_alloc()' call, it must be
undone by a corresponding 'kfifo_free()' call, as already done in the
remove function.
While at it, move the 'platform_device_put()' call to this new error
handling path and explicitly return 0 in the success path.
Theoretically, it will cause index out of bounds error if
'num_bytes_read' is greater than 4. As we expect it(and was tested)
never to be greater than 4, error out if it happens.
For some reason lost in history function vchiq_mmal_init used
a static variable for storing the vchiq_instance.
This value is retrieved from vchiq per instance, so worked fine
until you try to call vchiq_mmal_init multiple times concurrently
when things then go wrong. This seemed to happen quite frequently
if using the cutdown firmware (no MMAL or VCSM services running)
as the vchiq_connect then failed, and one or other vchiq_shutdown
was working on an invalid handle.
Remove the static so that each caller gets a unique vchiq_instance.
Fixes: 7b3ad5abf027 ("staging: Import the BCM2835 MMAL-based V4L2 camera driver.") Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Link: https://lore.kernel.org/r/1621979857-26754-1-git-send-email-stefan.wahren@i2se.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.
As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.
Add cleanup function as the name variable for the partition name was
allocaed but never freed after the use as the add mtd function
duplicate the name and free the pparts struct as the partition name is
assumed to be static.
The leak was found using kmemleak.
fis-index-block is seeked in the master node and not in the partitions node.
For following binding and current usage, the driver need to check the
partitions subnode.
Fixes: c0e118c8a1a3 ("mtd: partitions: Add OF support to RedBoot partitions") Signed-off-by: Corentin Labbe <clabbe@baylibre.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20210520114851.1274609-1-clabbe@baylibre.com Signed-off-by: Sasha Levin <sashal@kernel.org>
tuple_set_u64() produces a signed value instead of an unsigned value.
That works for database export but not other cases. Rename to
tuple_set_d64() for database export and fix tuple_set_u64().
Fixes: df919b400ad3f ("perf scripting python: Extend interface to export data in a database-friendly way") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Link: https://lore.kernel.org/r/20210525095112.1399-2-adrian.hunter@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 06e8f5c842f2d ("ASoC: rsnd: don't call clk_get_rate() under
atomic context") used saved clk_rate, thus for_each_rsnd_clk()
is no longer needed. This patch fixes it.
Fixes: 06e8f5c842f2d ("ASoC: rsnd: don't call clk_get_rate() under atomic context") Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Link: https://lore.kernel.org/r/87v978oe2u.wl-kuninori.morimoto.gx@renesas.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During PR_SWAP, When TCPM is in PR_SWAP_SNK_SRC_SINK_OFF, vbus is
expected to reach VSAFE0V when source turns off vbus. Do not move
to SNK_UNATTACHED state when this happens.
Fix the missing clk_disable_unprepare() before return
from rk3328_platform_probe() in the error handling case.
Fixes: c32759035ad2 ("ASoC: rockchip: support ACODEC for rk3328") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20210518075847.1116983-1-yangyingliang@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add __aligned(8) to ensure the buffer passed to
iio_push_to_buffers_with_timestamp() is suitable for the naturally
aligned timestamp that will be inserted.
Here structure is not used, because this buffer is also used
elsewhere in the driver.
Fixes: 67e17300dc1d ("iio: potentiostat: add LMP91000 support") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Matt Ranostay <matt.ranostay@konsulko.com> Acked-by: Matt Ranostay <matt.ranostay@konsulko.com> Link: https://lore.kernel.org/r/20210501171352.512953-8-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The samples buffer is passed to iio_push_to_buffers_with_timestamp()
which requires a buffer aligned to 8 bytes as it is assumed that
the timestamp will be naturally aligned if present.
Fixes tag is inaccurate but prior to that likely manual backporting needed
(for anything before 4.18) Earlier than that the include file to fix is
drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.h:
commit 974e6f02e27 ("iio: cros_ec_sensors_core: Add common functions
for the ChromeOS EC Sensor Hub.") present since kernel stable 4.10.
(Thanks to Gwendal for tracking this down)
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of uses of
iio_push_to_buffers_with_timestamp().
Fixes tag is not strictly accurate as prior to that patch there was
potentially an unaligned write. However, any backport past there will
need to be done manually.
Fixes: 0624bf847dd0 ("iio:tcs3472: Use iio_push_to_buffers_with_timestamp()") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210501170121.512209-20-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Found during an audit of all calls of uses of
iio_push_to_buffers_with_timestamp()
Fixes: a244e7b57f0f ("iio: Add driver for AMS/TAOS tcs3414 digital color sensor") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210501170121.512209-19-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The bulk read size is based on the size of an array that also has
space for the timestamp alongside the channels.
Fix that and also fix alignment of the buffer passed
to iio_push_to_buffers_with_timestamp.
Found during an audit of all calls to this function.
Fixes: 1ce0eda0f757 ("iio: mxc4005: add triggered buffer mode for mxc4005") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210501170121.512209-6-jic23@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
To make code more readable, use a structure to express the channel
layout and ensure the timestamp is 8 byte aligned.
Note this matches what was done in all the other hid sensor drivers.
This one was missed previously due to an extra level of indirection.
Found during an audit of all calls of this function.
projects / thirdparty / kernel / stable.git / log
