Flags (PIPE_BUF_FLAG_PACKET, PIPE_BUF_FLAG_GIFT) could remain on the
unused part of the pipe ring buffer. Previously splice_to_pipe() left
the flags value alone, which could result in incorrect behavior.
Uninitialized flags appears to have been there from the introduction of
the splice syscall.
Link layer protocols may unconditionally pull headers, as Ethernet
does in eth_type_trans. Ensure that the entire link layer header
always lies in the skb linear segment. tpacket_snd has such a check.
Extend this to packet_snd.
Variable length link layer headers complicate the computation
somewhat. Here skb->len may be smaller than dev->hard_header_len.
Round up the linear length to be at least as long as the smallest of
the two.
[js] no virtio helpers in 3.12
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Macvtap functions read the value once, but unless READ_ONCE is used,
the compiler may ignore this and read multiple times. Enforce a single
read and locally cached value to avoid updates between test and use.
Signed-off-by: Willem de Bruijn <willemb@google.com> Suggested-by: Eric Dumazet <edumazet@google.com> Acked-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[wt: s/READ_ONCE/ACCESS_ONCE]
sysrq_sched_debug_show() can dump a lot of information. Don't print out
all that if we're just trying to get a list of blocked tasks (SysRq-W).
The information is still accessible with SysRq-T.
Signed-off-by: Rabin Vincent <rabinv@axis.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1459777322-30902-1-git-send-email-rabin.vincent@axis.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Nikolay Borisov <n.borisov.lkml@gmail.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
do_generic_file_read() can be told to perform a large request from
userspace. If the system is under OOM and the reading task is the OOM
victim then it has an access to memory reserves and finishing the full
request can lead to the full memory depletion which is dangerous. Make
sure we rather go with a short read and allow the killed task to
terminate.
Link: http://lkml.kernel.org/r/20170201092706.9966-3-mhocko@kernel.org Signed-off-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Patch series "fix a kernel oops when reading sysfs valid_zones", v2.
A sysfs memory file is created for each 2GiB memory block on x86-64 when
the system has 64GiB or more memory. [1] When the start address of a
memory block is not backed by struct page, i.e. a memory range is not
aligned by 2GiB, reading its 'valid_zones' attribute file leads to a
kernel oops. This issue was observed on multiple x86-64 systems with
more than 64GiB of memory. This patch-set fixes this issue.
Patch 1 first fixes an issue in test_pages_in_a_zone(), which does not
test the start section.
Patch 2 then fixes the kernel oops by extending test_pages_in_a_zone()
to return valid [start, end).
Note for stable kernels: The memory block size change was made by commit bdee237c0343 ("x86: mm: Use 2GB memory block size on large-memory x86-64
systems"), which was accepted to 3.9. However, this patch-set depends
on (and fixes) the change to test_pages_in_a_zone() made by commit 5f0f2887f4de ("mm/memory_hotplug.c: check for missing sections in
test_pages_in_a_zone()"), which was accepted to 4.4.
So, I recommend that we backport it up to 4.4.
[1] 'Commit bdee237c0343 ("x86: mm: Use 2GB memory block size on
large-memory x86-64 systems")'
This patch (of 2):
test_pages_in_a_zone() does not check 'start_pfn' when it is aligned by
section since 'sec_end_pfn' is set equal to 'pfn'. Since this function
is called for testing the range of a sysfs memory file, 'start_pfn' is
always aligned by section.
Fix it by properly setting 'sec_end_pfn' to the next section pfn.
Also make sure that this function returns 1 only when the range belongs
to a zone.
Here, If devm_ioremap will fail. It will return NULL.
Then hpriv->base = NULL - 0x20000; Kernel can run into
a NULL-pointer dereference. This error check will avoid
NULL pointer dereference.
Based on the xf86-video-nv code, NFORCE (NV1A) and NFORCE2 (NV1F) have a
different way of retrieving clocks. See the
nv_hw.c:nForceUpdateArbitrationSettings function in the original code
for how these clocks were accessed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54587 Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
In the unix_bind() code path, unix_mknod() does not have to
be done with u->bindlock held, since it is a pure fs operation,
so we can just move unix_mknod() out.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Tested-by: Dmitry Vyukov <dvyukov@google.com> Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
Just like commit 4acd4945cd1e ("ipv6: addrconf: Avoid calling
netdevice notifiers with RCU read-side lock"), it is unnecessary
to make addrconf_disable_change() use RCU iteration over the
netdev list, since it already holds the RTNL lock, or we may meet
Illegal context switch in RCU read-side critical section.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
Xuan Qi reports that the Linux NFSv4 client failed to lock a file
that was migrated. The steps he observed on the wire:
1. The client sent a LOCK request to the source server
2. The source server replied NFS4ERR_MOVED
3. The client switched to the destination server
4. The client sent the same LOCK request to the destination
server with a bumped lock sequence ID
5. The destination server rejected the LOCK request with
NFS4ERR_BAD_SEQID
RFC 3530 section 8.1.5 provides a list of NFS errors which do not
bump a lock sequence ID.
However, RFC 3530 is now obsoleted by RFC 7530. In RFC 7530 section
9.1.7, this list has been updated by the addition of NFS4ERR_MOVED.
Reported-by: Xuan Qi <xuan.qi@oracle.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
In swab.h the "#if BITS_PER_LONG > 32" breaks compiling userspace programs if
BITS_PER_LONG is #defined by userspace with the sizeof() compiler builtin.
Solve this problem by using __BITS_PER_LONG instead. Since we now
#include asm/bitsperlong.h avoid further potential userspace pollution
by moving the #define of SHIFT_PER_LONG to bitops.h which is not
exported to userspace.
This patch unbreaks compiling qemu on hppa/parisc.
After emulating an unaligned access in delay slot of a branch, we
pretend as the delay slot never happened - so return back to actual
branch target (or next PC if branch was not taken).
Curently we did this by handling STATUS32.DE, we also need to clear the
BTA.T bit, which is disregarded when returning from original misaligned
exception, but could cause weirdness if it took the interrupt return
path (in case interrupt was acive too)
One ARC700 customer ran into this when enabling unaligned access fixup
for kernel mode accesses as well
With some gcc versions, we get a warning about the eicon driver,
and that currently shows up as the only remaining warning in one
of the build bots:
In file included from ../drivers/isdn/hardware/eicon/message.c:30:0:
eicon/message.c: In function 'mixer_notify_update':
eicon/platform.h:333:18: warning: array subscript is above array bounds [-Warray-bounds]
The code is easily changed to open-code the unusual PUT_WORD() line
causing this to avoid the warning.
Until interface is up [and assuming ringparams weren't explicitly
configured] when queried for the size of its rings bnx2x would
claim they're the maximal size by default.
That is incorrect as by default the maximal number of buffers would
be equally divided between the various rx rings.
This prevents the user from actually setting the number of elements
on each rx ring to be of maximal size prior to transitioning the
interface into up state.
To fix this, make a rough estimation about the number of buffers.
It wouldn't always be accurate, but it would be much better than
current estimation and would allow users to increase number of
buffers during early initialization of the interface.
Reported-by: Seymour, Shane <shane.seymour@hpe.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed. Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device. Those end up
racing with the EEH recovery, crashing it. Similar races were also
observed when opening the device and when shutting it down during
recovery.
This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards. Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery. This is similar to the solution used by the JSM serial
driver.
I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
In sg_common_write(), we free the block request and return -ENODEV if
the device is detached in the middle of the SG_IO ioctl().
Unfortunately, sg_finish_rem_req() also tries to free srp->rq, so we
end up freeing rq->cmd in the already free rq object, and then free
the object itself out from under the current user.
This ends up corrupting random memory via the list_head on the rq
object. The most common crash trace I saw is this:
The solution is straightforward: just set srp->rq to NULL in the
failure branch so that sg_finish_rem_req() doesn't attempt to re-free
it.
Additionally, since sg_rq_end_io() will never be called on the object
when this happens, we need to free memory backing ->cmd if it isn't
embedded in the object itself.
KASAN was extremely helpful in finding the root cause of this bug.
Signed-off-by: Calvin Owens <calvinowens@fb.com> Acked-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Acked-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
We received two reports of BUG_ON in bnad_txcmpl_process() where
hw_consumer_index appeared to be ahead of producer_index. Out of order
write/read of these variables could explain these reports.
bnad_start_xmit(), as a producer of tx descriptors, has a few memory
barriers sprinkled around writes to producer_index and the device's
doorbell but they're not paired with anything in bnad_txcmpl_process(), a
consumer.
Since we are synchronizing with a device, we must use mandatory barriers,
not smp_*. Also, I didn't see the purpose of the last smp_mb() in
bnad_start_xmit().
Signed-off-by: Benjamin Poirier <bpoirier@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
The VFIO_DEVICE_SET_IRQS ioctl did not sufficiently sanitize
user-supplied integers, potentially allowing memory corruption. This
patch adds appropriate integer overflow checks, checks the range bounds
for VFIO_IRQ_SET_DATA_NONE, and also verifies that only single element
in the VFIO_IRQ_SET_DATA_TYPE_MASK bitmask is set.
VFIO_IRQ_SET_ACTION_TYPE_MASK is already correctly checked later in
vfio_pci_set_irqs_ioctl().
Furthermore, a kzalloc is changed to a kcalloc because the use of a
kzalloc with an integer multiplication allowed an integer overflow
condition to be reached without this patch. kcalloc checks for overflow
and should prevent a similar occurrence.
the policy_lock parameter is a one way switch that prevents policy
from being further modified. Unfortunately some of the module parameters
can effectively modify policy by turning off enforcement.
split policy_admin_capable into a view check and a full admin check,
and update the admin check to test the policy_lock parameter.
Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
BugLink: http://bugs.launchpad.net/bugs/1592547
If unpack_dfa() returns NULL due to the dfa not being present,
profile_unpack() is not checking if the dfa is not present (NULL).
Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
The current behavior is confusing as it causes exec failures to report
the executable is missing instead of identifying that apparmor
caused the failure.
Signed-off-by: John Johansen <john.johansen@canonical.com> Acked-by: Seth Arnold <seth.arnold@canonical.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
BugLink: http://bugs.launchpad.net/bugs/1268727
The task field in the lsm_audit struct needs to be initialized if
a change_hat fails, otherwise the following oops will occur
The patch
Fs/cifs: make share unaccessible at root level mountable
makes use of prepaths when any component of the underlying path is
inaccessible.
When mounting 2 separate shares having different prepaths but are other
wise similar in other respects, we end up sharing superblocks when we
shouldn't be doing so.
vmxnet3_reset_work() expects tx queues to be stopped (via
vmxnet3_quiesce_dev -> netif_tx_disable). However, this races with the
netif_wake_queue() call in netif_tx_timeout() such that the driver's
start_xmit routine may be called unexpectedly, triggering one of the BUG_ON
in vmxnet3_map_pkt with a stack trace like this:
If the OPEN rpc call to the server fails with an ENOENT call, nfs_atomic_open
will create a negative dentry for that file, however it currently fails
to call nfs_set_verifier(), thus causing the dentry to be immediately
revalidated on the next call to nfs_lookup_revalidate() instead of following
the usual lookup caching rules.
Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.
This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.
Tested-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment] Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
On APQ8060, the kernel crashes in arch_hw_breakpoint_init, taking an
undefined instruction trap within write_wb_reg. This is because Scorpion
CPUs erroneously appear to set DBGPRSR.SPD when WFI is issued, even if
the core is not powered down. When DBGPRSR.SPD is set, breakpoint and
watchpoint registers are treated as undefined.
It's possible to trigger similar crashes later on from userspace, by
requesting the kernel to install a breakpoint or watchpoint, as we can
go idle at any point between the reset of the debug registers and their
later use. This has always been the case.
Given that this has always been broken, no-one has complained until now,
and there is no clear workaround, disable hardware breakpoints and
watchpoints on Scorpion to avoid these issues.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reported-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Stephen Boyd <sboyd@codeaurora.org> Acked-by: Will Deacon <will.deacon@arm.com> Cc: Russell King <linux@armlinux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Willy Tarreau <w@1wt.eu>
During code inspection, while investigating following stack trace
seen on one of the test setup, we found out there was possibility
of memory leak becuase driver was not unwinding the stack properly.
This issue has not been reproduced in a test environment or on a
customer setup.
Both bridges advertise the 0xf000-0xffff window, which cannot be correct.
Work around this by ignoring _CRS on this system. The downside is that we
may not assign resources correctly to hot-added PCI devices (if they are
possible on this system).
Always stating PIN_CONFIG_BIAS_DISABLE is supported gives untrue output
when examining /sys/kernel/debug/pinctrl/e6060000.pfc/pinconf-pins if
the operation get_bias() is implemented but the pin is not handled by
the get_bias() implementation. In that case the output will state that
"input bias disabled" indicating that this pin has bias control
support.
Make support for PIN_CONFIG_BIAS_DISABLE depend on that the pin either
supports SH_PFC_PIN_CFG_PULL_UP or SH_PFC_PIN_CFG_PULL_DOWN. This also
solves the issue where SoC specific implementations print error messages
if their particular implementation of {set,get}_bias() is called with a
pin it does not know about.
The sysrq input handler should be attached to the input device which has
a left alt key.
On 32-bit kernels, some input devices which has a left alt key cannot
attach sysrq handler. Because the keybit bitmap in struct input_device_id
for sysrq is not correctly initialized. KEY_LEFTALT is 56 which is
greater than BITS_PER_LONG on 32-bit kernels.
I found this problem when using a matrix keypad device which defines
a KEY_LEFTALT (56) but doesn't have a KEY_O (24 == 56%32).
So it must be dereferenced to be used in calculation of pci_base:
*pci_base = (dma_addr_t)*vme_base + pci_offset;
This bug was caught thanks to the following gcc warning:
drivers/vme/bridges/vme_ca91cx42.c: In function ‘ca91cx42_slave_get’:
drivers/vme/bridges/vme_ca91cx42.c:467:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
*pci_base = (dma_addr_t)vme_base + pci_offset;
i2c_smbus_xfer() does not always fill an entire block, allowing
kernel stack memory disclosure through the temp variable. Clear
it before it's read to.
This driver reports misc scan input events on the sensor's status
register changes. But the event capability for them was not set in the
device initialization, so these events were ignored.
This change adds the missing event capability.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
This driver reports input events on their interrupts which are triggered
by the sensor's status register changes. But only single bit change is
reported in the interrupt handler. So if there are multiple bits are
changed at almost the same time, other press or release events are ignored.
This fixes it by detecting all changed bits in the status register.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
The TCA8418 might be used using different interrupt triggers on various
boards. This is not working so far because the current code forces a
falling edge trigger.
The device tree already provides a trigger type, so let's use whatever it
sets up, and since we can be loaded without DT, keep the old behaviour for
the non-DT case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Oliver Neukum <ONeukum@suse.com> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
Postpone axis initialization to the first open instead of doing it
in joydev_connect. This is to make sure the generated startup events
are representative of the current joystick state rather than what
it was when joydev_connect() was called, potentially much earlier.
Once the first user is connected to joydev node we'll be updating
joydev->abs[] values and subsequent clients will be getting correct
initial states as well.
This solves issues with joystick driven menus that start scrolling
up each time they are started, until the user moves the joystick to
generate events. In emulator menu setups where the menu program is
restarted every time the game exits, the repeated need to move the
joystick to stop the unintended scrolling gets old rather quickly...
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
When a system receives a Query, it does not respond immediately.
Instead, it delays its response by a random amount of time, bounded
by the Max Resp Time value derived from the Max Resp Code in the
received Query message. A system may receive a variety of Queries on
different interfaces and of different kinds (e.g., General Queries,
Group-Specific Queries, and Group-and-Source-Specific Queries), each
of which may require its own delayed response.
Before scheduling a response to a Query, the system must first
consider previously scheduled pending responses and in many cases
schedule a combined response. Therefore, the system must be able to
maintain the following state:
o A timer per interface for scheduling responses to General Queries.
o A per-group and interface timer for scheduling responses to Group-
Specific and Group-and-Source-Specific Queries.
o A per-group and interface list of sources to be reported in the
response to a Group-and-Source-Specific Query.
When a new Query with the Router-Alert option arrives on an
interface, provided the system has state to report, a delay for a
response is randomly selected in the range (0, [Max Resp Time]) where
Max Resp Time is derived from Max Resp Code in the received Query
message. The following rules are then used to determine if a Report
needs to be scheduled and the type of Report to schedule. The rules
are considered in order and only the first matching rule is applied.
1. If there is a pending response to a previous General Query
scheduled sooner than the selected delay, no additional response
needs to be scheduled.
2. If the received Query is a General Query, the interface timer is
used to schedule a response to the General Query after the
selected delay. Any previously pending response to a General
Query is canceled.
--8<--
Currently the timer is rearmed with new random expiration time for
every incoming query regardless of possibly already pending report.
Which is not aligned with the above RFE.
It also might happen that higher rate of incoming queries can
postpone the report after the expiration time of the first query
causing group membership loss.
Now the per interface general query timer is rearmed only
when there is no pending report already scheduled on that interface or
the newly selected expiration time is before the already pending
scheduled report.
Signed-off-by: Michal Tesar <mtesar@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
Final nlmsg_len field update must reflect inserted net_dm_drop_point
data.
This patch depends on previous patch:
"drop_monitor: add missing call to genlmsg_end"
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
Update nlmsg_len field with genlmsg_end to enable userspace processing
using nlmsg_next helper. Also adds error handling.
Signed-off-by: Reiter Wolfgang <wr0112358@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
When a disfunctional timer, e.g. dummy timer, is installed, the tick core
tries to setup the broadcast timer.
If no broadcast device is installed, the kernel crashes with a NULL pointer
dereference in tick_broadcast_setup_oneshot() because the function has no
sanity check.
Reported-by: Mason <slash.tmp@free.fr> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Anna-Maria Gleixner <anna-maria@linutronix.de> Cc: Richard Cochran <rcochran@linutronix.de> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Peter Zijlstra <peterz@infradead.org>, Cc: Sebastian Frias <sf84@laposte.net> Cc: Thibaud Cornic <thibaud_cornic@sigmadesigns.com> Cc: Robin Murphy <robin.murphy@arm.com> Link: http://lkml.kernel.org/r/1147ef90-7877-e4d2-bb2b-5c4fa8d3144b@free.fr Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
cpmac_start_xmit() used the max() macro on skb->len (an unsigned int)
and ETH_ZLEN (a signed int literal). This led to the following compiler
warning:
In file included from include/linux/list.h:8:0,
from include/linux/module.h:9,
from drivers/net/ethernet/ti/cpmac.c:19:
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_start_xmit':
include/linux/kernel.h:748:17: warning: comparison of distinct pointer
types lacks a cast
(void) (&_max1 == &_max2); \
^
drivers/net/ethernet/ti/cpmac.c:560:8: note: in expansion of macro 'max'
len = max(skb->len, ETH_ZLEN);
^
On top of this, it assigned the result of the max() macro to a signed
integer whilst all further uses of it result in it being cast to varying
widths of unsigned integer.
Fix this up by using max_t to ensure the comparison is performed as
unsigned integers, and for consistency change the type of the len
variable to unsigned int.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Willy Tarreau <w@1wt.eu>
The current_user_ns() macro currently returns &init_user_ns when user
namespaces are disabled, and that causes several warnings when building
with gcc-6.0 in code that compares the result of the macro to
&init_user_ns itself:
fs/xfs/xfs_ioctl.c: In function 'xfs_ioctl_setattr_check_projid':
fs/xfs/xfs_ioctl.c:1249:22: error: self-comparison always evaluates to true [-Werror=tautological-compare]
if (current_user_ns() == &init_user_ns)
This is a legitimate warning in principle, but here it isn't really
helpful, so I'm reprasing the definition in a way that shuts up the
warning. Apparently gcc only warns when comparing identical literals,
but it can figure out that the result of an inline function can be
identical to a constant expression in order to optimize a condition yet
not warn about the fact that the condition is known at compile time.
This is exactly what we want here, and it looks reasonable because we
generally prefer inline functions over macros anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Serge Hallyn <serge.hallyn@canonical.com> Cc: David Howells <dhowells@redhat.com> Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com> Cc: James Morris <james.l.morris@oracle.com> Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Matt Fleming reported seeing crashes when enabling and disabling
function profiling which uses function graph tracer. Later Namhyung Kim
hit a similar issue and he found that the issue was due to the jmp to
ftrace_stub in ftrace_graph_call was only two bytes, and when it was
changed to jump to the tracing code, it overwrote the ftrace_stub that
was after it.
Masami Hiramatsu bisected this down to a binutils change:
This patch adds -mshared option to x86 ELF assembler. By default,
assembler will optimize out non-PLT relocations against defined non-weak
global branch targets with default visibility. The -mshared option tells
the assembler to generate code which may go into a shared library
where all non-weak global branch targets with default visibility can
be preempted. The resulting code is slightly bigger. This option
only affects the handling of branch instructions.
Declaring ftrace_stub as a weak call prevents gas from using two byte
jumps to it, which would be converted to a jump to the function graph
code.
Link: http://lkml.kernel.org/r/20160516230035.1dbae571@gandalf.local.home Reported-by: Matt Fleming <matt@codeblueprint.co.uk> Reported-by: Namhyung Kim <namhyung@kernel.org> Tested-by: Matt Fleming <matt@codeblueprint.co.uk> Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Both damn things interpret userland pointers embedded into the payload;
worse, they are actually traversing those. Leaving aside the bad
API design, this is very much _not_ safe to call with KERNEL_DS.
Bail out early if that happens.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Willy Tarreau <w@1wt.eu>
GCC 5 generates different code for this bootwrapper null check that
causes the PS3 to hang very early in its bootup. This check is of
limited value, so just get rid of it.
What matters when deciding if we should make a page uptodate is
not how much we _wanted_ to copy, but how much we actually have
copied. As it is, on architectures that do not zero tail on
short copy we can leave uninitialized data in page marked uptodate.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Willy Tarreau <w@1wt.eu>
After sending an authorizer (ceph_x_authorize_a + ceph_x_authorize_b),
the client gets back a ceph_x_authorize_reply, which it is supposed to
verify to ensure the authenticity and protect against replay attacks.
The code for doing this is there (ceph_x_verify_authorizer_reply(),
ceph_auth_verify_authorizer_reply() + plumbing), but it is never
invoked by the the messenger.
AFAICT this goes back to 2009, when ceph authentication protocols
support was added to the kernel client in 4e7a5dcd1bba ("ceph:
negotiate authentication protocol; implement AUTH_NONE protocol").
The second param of ceph_connection_operations::verify_authorizer_reply
is unused all the way down. Pass 0 to facilitate backporting, and kill
it in the next commit.
The buffer for iucv_message_receive() needs to be below 2 GB. In
__iucv_message_receive(), the buffer address is casted to an u32, which
would result in either memory corruption or an addressing exception when
using addresses >= 2 GB.
Fix this by using GFP_DMA for the buffer allocation.
We previously made sure that the reported disk capacity was less than
0xffffffff blocks when the kernel was not compiled with large sector_t
support (CONFIG_LBDAF). However, this check assumed that the capacity
was reported in units of 512 bytes.
Add a sanity check function to ensure that we only enable disks if the
entire reported capacity can be expressed in terms of sector_t.
Reported-by: Steve Magnani <steve.magnani@digidescorp.com> Cc: Bart Van Assche <Bart.VanAssche@sandisk.com> Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
Kefeng Wang discovered that old versions of the QEMU CD driver would
return mangled mode data causing us to walk off the end of the buffer in
an attempt to parse it. Sanity check the returned mode sense data.
Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
We see lpfc devices regularly fail during kexec. Fix this by adding a
shutdown method which mirrors the remove method.
Signed-off-by: Anton Blanchard <anton@samba.org> Reviewed-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
The following fixes a divide by zero OOPs with TYPE_TAPE
due to pscsi_tape_read_blocksize() failing causing a zero
sd->sector_size being propigated up via dev_attrib.hw_block_size.
It also fixes another long-standing bug where TYPE_TAPE and
TYPE_MEDIMUM_CHANGER where using pscsi_create_type_other(),
which does not call scsi_device_get() to take the device
reference. Instead, rename pscsi_create_type_rom() to
pscsi_create_type_nondisk() and use it for all cases.
Finally, also drop a dump_stack() in pscsi_get_blocks() for
non TYPE_DISK, which in modern target-core can get invoked
via target_sense_desc_format() during CHECK_CONDITION.
[js] cast max_sectors to unsigned to avoid warnings
On I/O errors, the Windows driver doesn't set data_transfer_length
on error conditions other than SRB_STATUS_DATA_OVERRUN.
In these cases we need to set data_transfer_length to 0,
indicating there is no data transferred. On SRB_STATUS_DATA_OVERRUN,
data_transfer_length is set by the Windows driver to the actual data transferred.
Reported-by: Shiva Krishna <Shiva.Krishna@nimblestorage.com> Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
When sense message is present on error, we should pass along to the upper
layer to decide how to deal with the error.
This patch fixes connectivity issues with Fiber Channel devices.
Signed-off-by: Long Li <longli@microsoft.com> Reviewed-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
Don't crash the machine just because of an empty transfer. Use WARN_ON()
combined with returning an error.
Found by Dmitry Vyukov and syzkaller.
[ Changed to "WARN_ON_ONCE()". Al has a patch that should fix the root
cause, but a BUG_ON() is not acceptable in any case, and a WARN_ON()
might still be a cause of excessive log spamming.
NOTE! If this warning ever triggers, we may end up leaking resources,
since this doesn't bother to try to clean the command up. So this
WARN_ON_ONCE() triggering does imply real problems. But BUG_ON() is
much worse.
People really need to stop using BUG_ON() for "this shouldn't ever
happen". It makes pretty much any bug worse. - Linus ]
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de> Reported-by: Dmitry Vyukov <dvyukov@google.com> Cc: James Bottomley <jejb@linux.vnet.ibm.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
A race between scanning and fc_remote_port_delete() may result in a
permanent stop if the device gets blocked before scsi_sysfs_add_sdev()
and unblocked after. The reason is that blocking a device sets both the
SDEV_BLOCKED state and the QUEUE_FLAG_STOPPED. However,
scsi_sysfs_add_sdev() unconditionally sets SDEV_RUNNING which causes the
device to be ignored by scsi_target_unblock() and thus never have its
QUEUE_FLAG_STOPPED cleared leading to a device which is apparently
running but has a stopped queue.
We actually have two places where SDEV_RUNNING is set: once in
scsi_add_lun() which respects the blocked flag and once in
scsi_sysfs_add_sdev() which doesn't. Since the second set is entirely
spurious, simply remove it to fix the problem.
Reported-by: Zengxi Chen <chenzengxi@huawei.com> Signed-off-by: Wei Fang <fangwei1@huawei.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
ast_get_dram_info() configures a window in order to access BMC memory.
A BMC register can be configured to disallow this, and if so, causes
an infinite loop in the ast driver which renders the system unusable.
Fix this by erroring out if an error is detected. On powerpc systems with
EEH, this leads to the device being fenced and the system continuing to
operate.
When there is a CRC error in the SPROM read from the device, the code
attempts to handle a fallback SPROM. When this also fails, the driver
returns zero rather than an error code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
If we try to allocate memory pages to back an xfs_buf that we're trying
to read, it's possible that we'll be so short on memory that the page
allocation fails. For a blocking read we'll just wait, but for
readahead we simply dump all the pages we've collected so far.
Unfortunately, after dumping the pages we neglect to clear the
_XBF_PAGES state, which means that the subsequent call to xfs_buf_free
thinks that b_pages still points to pages we own. It then double-frees
the b_pages pages.
This results in screaming about negative page refcounts from the memory
manager, which xfs oughtn't be triggering. To reproduce this case,
mount a filesystem where the size of the inodes far outweighs the
availalble memory (a ~500M inode filesystem on a VM with 300MB memory
did the trick here) and run bulkstat in parallel with other memory
eating processes to put a huge load on the system. The "check summary"
phase of xfs_scrub also works for this purpose.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Cc: Ivan Kozik <ivan@ludios.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Signed-off-by: Willy Tarreau <w@1wt.eu>
xlog_recover_clear_agi_bucket didn't set the
type to XFS_BLFT_AGI_BUF, so we got a warning during log
replay (or an ASSERT on a debug build).
XFS (md0): Unknown buffer type 0!
XFS (md0): _xfs_buf_ioapply: no ops on block 0xaea8802/0x1
Fix this, as was done in f19b872b for 2 other locations
with the same problem.
Signed-off-by: Eric Sandeen <sandeen@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
The function xen_guest_init is using __alloc_percpu with an alignment
which are not power of two.
However, the percpu allocator never supported alignments which are not power
of two and has always behaved incorectly in thise case.
Commit 3ca45a4 "percpu: ensure requested alignment is power of two"
introduced a check which trigger a warning [1] when booting linux-next
on Xen. But in reality this bug was always present.
This can be fixed by replacing the call to __alloc_percpu with
alloc_percpu. The latter will use an alignment which are a power of two.
The UHCI controllers in Intel chipsets rely on a platform-specific non-PME
mechanism for wakeup signalling. They can generate wakeup signals even
though they don't support PME.
We need to let the USB core know this so that it will enable runtime
suspend for UHCI controllers.
usb_endpoint_maxp() returns wMaxPacketSize in its
raw form. Without taking into consideration that it
also contains other bits reserved for isochronous
endpoints.
This patch fixes one occasion where this is a
problem by making sure that we initialize
ep->maxpacket only with lower 10 bits of the value
returned by usb_endpoint_maxp(). Note that seperate
patches will be necessary to audit all call sites of
usb_endpoint_maxp() and make sure that
usb_endpoint_maxp() only returns lower 10 bits of
wMaxPacketSize.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
On a system with a defective USB device connected to an USB hub,
an endless sequence of port connect events was observed. The sequence
of events as observed is as follows:
- Port reports connected event (port status=USB_PORT_STAT_CONNECTION).
- Event handler debounces port and resets it by calling hub_port_reset().
- hub_port_reset() calls hub_port_wait_reset() to wait for the reset
to complete.
- The reset completes, but USB_PORT_STAT_CONNECTION is not immediately
set in the port status register.
- hub_port_wait_reset() returns -ENOTCONN.
- Port initialization sequence is aborted.
- A few milliseconds later, the port again reports a connected event,
and the sequence repeats.
This continues either forever or, randomly, stops if the connection
is already re-established when the port status is read. It results in
a high rate of udev events. This in turn destabilizes userspace since
the above sequence holds the device mutex pretty much continuously
and prevents userspace from actually reading the device status.
To prevent the problem from happening, let's wait for the connection
to be re-established after a port reset. If the device was actually
disconnected, the code will still return an error, but it will do so
only after the long reset timeout.
Cc: Douglas Anderson <dianders@chromium.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Upstream commit 98d74f9ceaef ("xhci: fix 10 second timeout on removal of
PCI hotpluggable xhci controllers") fixes a problem with hot pluggable PCI
xhci controllers which can result in excessive timeouts, to the point where
the system reports a deadlock.
The same problem is seen with hot pluggable xhci controllers using the
xhci-plat driver, such as the driver used for Type-C ports on rk3399.
Similar to hot-pluggable PCI controllers, the driver for this chip
removes the xhci controller from the system when the Type-C cable is
disconnected.
The solution for PCI devices works just as well for non-PCI devices
and avoids the problem.
Some gadget drivers are bad, bad boys. We notice
that ADB was passing bad Burst Size which caused top
bits of param0 to be overwritten which confused DWC3
when running this command.
In order to avoid future issues, we're going to make
sure values passed by macros are always safe for the
controller. Note that ADB still needs a fix to *not*
pass bad values.
Reported-by: Mohamed Abbas <mohamed.abbas@intel.com> Sugested-by: Adam Andruszak <adam.andruszak@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
Fix errors during open not being returned to userspace. Specifically,
failed control-line manipulations or control or read urb submissions
would not be detected.
If acm_submit_read_urbs() fails in acm_port_activate(), error handling
code calls usb_autopm_put_interface() while it is already called
before acm_submit_read_urbs(). The patch reorganizes error handling code
to avoid double decrement of USB interface's PM-usage counter.
Found by Linux Driver Verification project (linuxtesting.org).
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
Bind to the interface, but do not register any ports, after having
downloaded the firmware. The device will still disconnect and
re-enumerate, but this way we avoid an error messages from being logged
as part of the process:
io_ti: probe of 1-1.3:1.0 failed with error -5
Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Willy Tarreau <w@1wt.eu>
Andrey Konovalov's fuzz testing of gadgetfs showed that we should
improve the driver's checks for valid configuration descriptors passed
in by the user. In particular, the driver needs to verify that the
wTotalLength value in the descriptor is not too short (smaller
than USB_DT_CONFIG_SIZE). And the check for whether wTotalLength is
too large has to be changed, because the driver assumes there is
always enough room remaining in the buffer to hold a device descriptor
(at least USB_DT_DEVICE_SIZE bytes).
This patch adds the additional check and fixes the existing check. It
may do a little more than strictly necessary, but one extra check
won't hurt.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
The cause of the bug is subtle. The dev_config() routine gets called
twice by the fuzzer. The first time, the user data contains both a
full-speed configuration descriptor and a high-speed config
descriptor, causing dev->hs_config to be set. But it also contains an
invalid device descriptor, so the buffer containing the descriptors is
deallocated and dev_config() returns an error.
The second time dev_config() is called, the user data contains only a
full-speed config descriptor. But dev->hs_config still has the stale
pointer remaining from the first call, causing the routine to think
that there is a valid high-speed config. Later on, when the driver
dereferences the stale pointer to copy that descriptor, we get a
use-after-free access.
The fix is simple: Clear dev->hs_config if the passed-in data does not
contain a high-speed config descriptor.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
projects / thirdparty / kernel / stable.git / log
