wifi: ath12k: Split scan request for split band device
When two split-phy devices having supported frequency range in same band
(as mentioned below) are combined into an ath12k HW group, they will be
part of same wiphy and hence the channel list (wiphy->bands[]) will be
common for all of the radios (ar).
1 - 2.4 GHz + 5 GHz Low band
2 - 5 GHz High band + 6 GHz
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with both the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan as some frequencies in the scan
request are not supported, resulting is scan failure.
Fix this by splitting the scan request into multiples scans in driver
based on the supported frequency range of different radios in a band and
schedule scans in parallel to them.
Finally send scan completion/abort notification to mac80211 after all the
radios complete their scheduled scan.
Also, last_scan_link is not needed anymore as ath12k internally schedules
multiple scans, remove the same and use ahvif->links_map to identify
scan links when scan is cancelled.
Co-developed-by: Vignesh C <quic_vignc@quicinc.com> Signed-off-by: Vignesh C <quic_vignc@quicinc.com> Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com> Reviewed-by: Mahendran P <quic_mahep@quicinc.com> Link: https://patch.msgid.link/20250507194832.2501668-3-rameshkumar.sundaram@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
wifi: ath12k: Prepare ahvif scan link for parallel scan
When two split-phy devices that support overlapping frequency ranges within
the same band(say 5 GHz low and 5 GHz high) are grouped into an ath12k
hardware (HW) setup, they share a common wiphy instance. Consequently, the
channel list (wiphy->bands[]) becomes unified across all associated
radios (ar).
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with all the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan since some of the frequencies in
the scan request are not supported, resulting in a scan failure.
To fix this ath12k driver should split the scan request into multiple
scans based on requested frequencies and schedule them to corresponding
underlying radio(s) in parallel.
Currently, ath12k driver assigns the scan link (link 15) in ahvif->links[]
for scan vdev creation. However, with parallel scan support being
introduced in the following patch, multiple radios (e.g., 5 GHz low and
5 GHz high) in the same HW group may attempt to use the same scan link
concurrently, causing conflicts where the vdev created by one radio could
be deleted and re-initialized by another.
To address this, reserve space for additional scan links for each radio in
a MLO group and allow subsequent radios to use different available scan
links (ahvif->link[15..MAX_SCAN_LINKS]) when scan link (15) is
pre-occupied.
While at it, rename ATH12K_DEFAULT_SCAN_LINK as ATH12K_FIRST_SCAN_LINK
as there is no longer only one scan link.
Karthik M [Tue, 6 May 2025 21:49:30 +0000 (14:49 -0700)]
wifi: ath12k: disable pdev for non supported country
In MLO configuration, ath12k_mac_radio_start() iterates through all
the radios and makes the ar state 'ON'. Even though some bands are
not supported in certain countries, ath12k_reg_update_chan_list()
tries to update the channel list for all the active pdevs and ends
up in the warn_on for non-supported band.
To prevent this, disable the pdev when the number of channels across
all bands supported by the pdev is zero for a particular country.
wifi: ath12k: Avoid accessing uninitialized arvif->ar during beacon miss
During beacon miss handling, ath12k driver iterates over active virtual
interfaces (vifs) and attempts to access the radio object (ar) via
arvif->deflink->ar.
However, after commit aa80f12f3bed ("wifi: ath12k: defer vdev creation for
MLO"), arvif is linked to a radio only after vdev creation, typically when
a channel is assigned or a scan is requested.
For P2P capable devices, a default P2P interface is created by
wpa_supplicant along with regular station interfaces, these serve as dummy
interfaces for P2P-capable stations, lack an associated netdev and initiate
frequent scans to discover neighbor p2p devices. When a scan is initiated
on such P2P vifs, driver selects destination radio (ar) based on scan
frequency, creates a scan vdev, and attaches arvif to the radio. Once the
scan completes or is aborted, the scan vdev is deleted, detaching arvif
from the radio and leaving arvif->ar uninitialized.
While handling beacon miss for station interfaces, P2P interface is also
encountered in the vif iteration and ath12k_mac_handle_beacon_miss_iter()
tries to dereference the uninitialized arvif->deflink->ar.
Fix this by verifying that vdev is created for the arvif before accessing
its ar during beacon miss handling and similar vif iterator callbacks.
==========================================================================
wlp6s0: detected beacon loss from AP (missed 7 beacons) - probing
KASAN: null-ptr-deref in range [0x0000000000000010-0x0000000000000017]
Kavita Kavita [Wed, 4 Jun 2025 10:57:57 +0000 (16:27 +0530)]
wifi: cfg80211: Add support for link reconfiguration negotiation offload to driver
In the case of SME-in-driver, the driver can internally choose to
update the links based on the AP MLD recommendation and do link
reconfiguration negotiation with AP MLD.
(e.g., After the driver processing the BSS Transition Management request
frame received from the AP MLD with Neighbor Report containing
Multi-Link element with recommended links information chooses to do link
reconfiguration negotiation with AP MLD).
To support this, extend cfg80211_mlo_reconf_add_done() and
NL80211_CMD_ASSOC_MLO_RECONF to indicate added links information for
driver-initiated link reconfiguration requests. For removed links,
the driver indicates links information using the
NL80211_CMD_LINKS_REMOVED event for driver-initiated cases, the same as
supplicant initiated cases.
For the driver-initiated case, cfg80211 will receive link
reconfiguration result asynchronously from driver so holding BSSes of
the accepted add links is needed in the event path. Also, no need of
unhold call for the rejected add link BSSes since there was no hold call
happened previously.
Once the supplicant receives the NL80211_CMD_ASSOC_MLO_RECONF event,
it needs to process the information about newly added links and install
per-link group keys (e.g., GTK/IGTK/BIGTK etc.).
In case of the SME-in-driver, using a vendor interface etc. to notify
the supplicant to initiate a link reconfiguration request and then
supplicant sending command to the cfg80211 can lead to race conditions.
The correct design to avoid this is that the driver indicates the
cfg80211 directly with the results of the link reconfiguration
negotiation.
Kavita Kavita [Wed, 4 Jun 2025 10:57:56 +0000 (16:27 +0530)]
wifi: cfg80211: Improve the documentation for NL80211_CMD_ASSOC_MLO_RECONF
The existing documentation for the NL80211_CMD_ASSOC_MLO_RECONF
does not clearly explain handling of link reconfiguration request
results from the driver.
Add documentation to explain that the command is used as an event to
notify userspace about added links information, and that the existing
NL80211_CMD_LINKS_REMOVED command is used to notify userspace about
removed links information.
Rafael Beims [Fri, 30 May 2025 09:47:04 +0000 (06:47 -0300)]
wifi: mwifiex: enable host mlme on sdio W8997 chipsets
Enable the host MLME flag to allow supported W8997 chipsets to
use WPA3. This feature requires firmware support (V2 API key), which
the driver validates before activation.
Tested using sdsd8997_combo_v4.bin from commit 211fbc287a0b ("linux-firmware: Update FW files for MRVL SD8997 chips")
Signed-off-by: Rafael Beims <rafael.beims@toradex.com> Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Acked-by: Brian Norris <briannorris@chromium.org> Link: https://patch.msgid.link/20250530094711.915574-1-rafael@beims.me Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wifi: mac80211: Fix bssid_indicator for MBSSID in AP mode
Currently, in ieee80211_assign_beacon() mbssid count is updated as link's
bssid_indicator. mbssid count is the total number of MBSSID elements in
the beacon instead of Max BSSID indicator of the Multiple BSS set.
This will result in drivers obtaining an invalid bssid_indicator for BSSes
in a Multiple BSS set.
Fix this by updating link's bssid_indicator from MBSSID element for
Transmitting BSS and update the same for all of its Non-Transmitting BSSes.
wifi: mac80211: Allow scan on a radio while operating on DFS on another radio
Currently, in multi-radio wiphy cases, if one radio is operating on a DFS
channel, -EBUSY is returned even when a scan is requested on a different
radio. Because of this, an MLD AP with one radio (link) on a DFS channel
and Automatic Channel Selection (ACS) on another radio (link) cannot be
brought up.
In multi-radio wiphy cases, multiple radios are grouped under a single
wiphy. Hence, if a radio is operating on a DFS channel and a scan is
requested on a different radio of the same wiphy, the scan can be allowed
simultaneously without impacting the DFS operations.
Add logic to check the underlying radio used for the requested scan. If the
radio on which DFS is already running is not being used, allow the scan
operation; otherwise, return -EBUSY.
wifi: mac80211: Allow DFS/CSA on a radio if scan is ongoing on another radio
Currently, in multi-radio wiphy cases, if a scan is ongoing on one radio,
-EBUSY is returned when DFS or a channel switch is initiated on another
radio. Because of this, an MLD AP with one radio (link) in an ongoing scan
cannot initiate DFS or a channel switch on another radio (link).
In multi-radio wiphy cases, multiple radios are grouped under a single
wiphy. Hence, if a scan is ongoing on one underlying radio and DFS or a
channel switch is requested on a different underlying radio of the same
wiphy, these operations can be allowed simultaneously.
Add logic to check the underlying radio used for the ongoing scan. If the
radio on which DFS or a channel switch is requested is not being used for
the scan, allow the operation; otherwise, return -EBUSY.
wifi: cfg80211: Add utility API to get radio index from channel
Add utility API cfg80211_get_radio_idx_by_chan() to retrieve the radio
index corresponding to a given channel in a multi-radio wiphy.
This utility function can be used when we want to check the radio-specific
data for a channel in a multi-radio wiphy. For example, it can help
determine the radio index required to handle a scan request. This index
can then be used to decide whether the scan can proceed without
interfering with ongoing DFS operations on another radio.
wifi: ieee80211: add Radio Measurement action fields
Drivers that support Tx power insertion could examine the outgoing Radio
measurement packet and depending on the packet type, the driver can
insert specific data fields in it. These action field values will help
drivers classify the action code within the Radio Measurement action
packet.
These action fields are defined in IEEE 802.11-2024 - Table 9-470, Radio
Measurement Action field values.
Linus Torvalds [Thu, 19 Jun 2025 17:21:32 +0000 (10:21 -0700)]
Merge tag 'net-6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from wireless.
The ath12k fix to avoid FW crashes requires adding support for a
number of new FW commands so it's quite large in terms of LoC. The
rest is relatively small.
Current release - fix to a fix:
- ptp: fix breakage after ptp_vclock_in_use() rework
Current release - regressions:
- openvswitch: allocate struct ovs_pcpu_storage dynamically, static
allocation may exhaust module loader limit on smaller systems
Previous releases - regressions:
- tcp: fix tcp_packet_delayed() for peers with no selective ACK
support
Previous releases - always broken:
- wifi: ath12k: don't activate more links than firmware supports
- tcp: make sure sockets open via passive TFO have valid NAPI ID
- eth: bnxt_en: update MRU and RSS table of RSS contexts on queue
reset, prevent Rx queues from silently hanging after queue reset
- NFC: uart: set tty->disc_data only in success path"
* tag 'net-6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (59 commits)
net: airoha: Differentiate hwfd buffer size for QDMA0 and QDMA1
net: airoha: Compute number of descriptors according to reserved memory size
tools: ynl: fix mixing ops and notifications on one socket
net: atm: fix /proc/net/atm/lec handling
net: atm: add lec_mutex
mlxbf_gige: return EPROBE_DEFER if PHY IRQ is not available
net: airoha: Always check return value from airoha_ppe_foe_get_entry()
NFC: nci: uart: Set tty->disc_data only in success path
calipso: Fix null-ptr-deref in calipso_req_{set,del}attr().
MAINTAINERS: Remove Shannon Nelson from MAINTAINERS file
net: lan743x: fix potential out-of-bounds write in lan743x_ptp_io_event_clock_get()
eth: fbnic: avoid double free when failing to DMA-map FW msg
tcp: fix passive TFO socket having invalid NAPI ID
selftests: net: add test for passive TFO socket NAPI ID
selftests: net: add passive TFO test binary
selftests: netdevsim: improve lib.sh include in peer.sh
tipc: fix null-ptr-deref when acquiring remote ip of ethernet bearer
Octeontx2-pf: Fix Backpresure configuration
net: ftgmac100: select FIXED_PHY
net: ethtool: remove duplicate defines for family info
...
Lorenzo Bianconi [Thu, 19 Jun 2025 07:07:25 +0000 (09:07 +0200)]
net: airoha: Differentiate hwfd buffer size for QDMA0 and QDMA1
EN7581 SoC allows configuring the size and the number of buffers in
hwfd payload queue for both QDMA0 and QDMA1.
In order to reduce the required DRAM used for hwfd buffers queues and
decrease the memory footprint, differentiate hwfd buffer size for QDMA0
and QDMA1 and reduce hwfd buffer size to 1KB for QDMA1 (WAN) while
maintaining 2KB for QDMA0 (LAN).
Lorenzo Bianconi [Thu, 19 Jun 2025 07:07:24 +0000 (09:07 +0200)]
net: airoha: Compute number of descriptors according to reserved memory size
In order to not exceed the reserved memory size for hwfd buffers,
compute the number of hwfd buffers/descriptors according to the
reserved memory size and the size of each hwfd buffer (2KB).
Fixes: 3a1ce9e3d01b ("net: airoha: Add the capability to allocate hwfd buffers via reserved-memory") Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://patch.msgid.link/20250619-airoha-hw-num-desc-v4-1-49600a9b319a@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 19 Jun 2025 15:38:40 +0000 (08:38 -0700)]
Merge tag 'wireless-2025-06-18' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
More fixes:
- ath12k
- avoid busy-waiting
- activate correct number of links
- iwlwifi
- iwldvm regression (lots of warnings)
- iwlmld merge damage regression (crash)
- fix build with some old gcc versions
- carl9170: don't talk to device w/o FW [syzbot]
- ath6kl: remove bad FW WARN [syzbot]
- ieee80211: use variable-length arrays [syzbot]
- mac80211
- remove WARN on delayed beacon update [syzbot]
- drop OCB frames with invalid source [syzbot]
* tag 'wireless-2025-06-18' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: Fix incorrect logic on cmd_ver range checking
wifi: iwlwifi: dvm: restore n_no_reclaim_cmds setting
wifi: iwlwifi: cfg: Limit cb_size to valid range
wifi: iwlwifi: restore missing initialization of async_handlers_list (again)
wifi: ath6kl: remove WARN on bad firmware input
wifi: carl9170: do not ping device which has failed to load firmware
wifi: ath12k: don't wait when there is no vdev started
wifi: ath12k: don't use static variables in ath12k_wmi_fw_stats_process()
wifi: ath12k: avoid burning CPU while waiting for firmware stats
wifi: ath12k: fix documentation on firmware stats
wifi: ath12k: don't activate more links than firmware supports
wifi: ath12k: update link active in case two links fall on the same MAC
wifi: ath12k: support WMI_MLO_LINK_SET_ACTIVE_CMDID command
wifi: ath12k: update freq range for each hardware mode
wifi: ath12k: parse and save sbs_lower_band_end_freq from WMI_SERVICE_READY_EXT2_EVENTID event
wifi: ath12k: parse and save hardware mode info from WMI_SERVICE_READY_EXT_EVENTID event for later use
wifi: ath12k: Avoid CPU busy-wait by handling VDEV_STAT and BCN_STAT
wifi: mac80211: don't WARN for late channel/color switch
wifi: mac80211: drop invalid source address OCB frames
wifi: remove zero-length arrays
====================
Jakub Kicinski [Wed, 18 Jun 2025 17:17:46 +0000 (10:17 -0700)]
tools: ynl: fix mixing ops and notifications on one socket
The multi message support loosened the connection between the request
and response handling, as we can now submit multiple requests before
we start processing responses. Passing the attr set to NlMsgs decoding
no longer makes sense (if it ever did), attr set may differ message
by messsage. Isolate the part of decoding responsible for attr-set
specific interpretation and call it once we identified the correct op.
Without this fix performing SET operation on an ethtool socket, while
being subscribed to notifications causes:
# File "tools/net/ynl/pyynl/lib/ynl.py", line 1096, in _op
# Exception| return self._ops(ops)[0]
# Exception| ~~~~~~~~~^^^^^
# File "tools/net/ynl/pyynl/lib/ynl.py", line 1040, in _ops
# Exception| nms = NlMsgs(reply, attr_space=op.attr_set)
# Exception| ^^^^^^^^^^^
The value of op we use on line 1040 is stale, it comes form the previous
loop. If a notification comes before a response we will update op to None
and the next iteration thru the loop will break with the trace above.
Fixes: 6fda63c45fe8 ("tools/net/ynl: fix cli.py --subscribe feature") Fixes: ba8be00f68f5 ("tools/net/ynl: Add multi message support to ynl") Reviewed-by: Donald Hunter <donald.hunter@gmail.com> Link: https://patch.msgid.link/20250618171746.1201403-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Wed, 18 Jun 2025 14:08:43 +0000 (14:08 +0000)]
net: atm: add lec_mutex
syzbot found its way in net/atm/lec.c, and found an error path
in lecd_attach() could leave a dangling pointer in dev_lec[].
Add a mutex to protect dev_lecp[] uses from lecd_attach(),
lec_vcc_attach() and lec_mcast_attach().
Following patch will use this mutex for /proc/net/atm/lec.
BUG: KASAN: slab-use-after-free in lecd_attach net/atm/lec.c:751 [inline]
BUG: KASAN: slab-use-after-free in lane_ioctl+0x2224/0x23e0 net/atm/lec.c:1008
Read of size 8 at addr ffff88807c7b8e68 by task syz.1.17/6142
David Thompson [Wed, 18 Jun 2025 13:59:02 +0000 (13:59 +0000)]
mlxbf_gige: return EPROBE_DEFER if PHY IRQ is not available
The message "Error getting PHY irq. Use polling instead"
is emitted when the mlxbf_gige driver is loaded by the
kernel before the associated gpio-mlxbf driver, and thus
the call to get the PHY IRQ fails since it is not yet
available. The driver probe() must return -EPROBE_DEFER
if acpi_dev_gpio_irq_get_by() returns the same.
Fixes: 6c2a6ddca763 ("net: mellanox: mlxbf_gige: Replace non-standard interrupt handling") Signed-off-by: David Thompson <davthompson@nvidia.com> Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250618135902.346-1-davthompson@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
NFC: nci: uart: Set tty->disc_data only in success path
Setting tty->disc_data before opening the NCI device means we need to
clean it up on error paths. This also opens some short window if device
starts sending data, even before NCIUARTSETDRIVER IOCTL succeeded
(broken hardware?). Close the window by exposing tty->disc_data only on
the success path, when opening of the NCI device and try_module_get()
succeeds.
The code differs in error path in one aspect: tty->disc_data won't be
ever assigned thus NULL-ified. This however should not be relevant
difference, because of "tty->disc_data=NULL" in nci_uart_tty_open().
calipso: Fix null-ptr-deref in calipso_req_{set,del}attr().
syzkaller reported a null-ptr-deref in sock_omalloc() while allocating
a CALIPSO option. [0]
The NULL is of struct sock, which was fetched by sk_to_full_sk() in
calipso_req_setattr().
Since commit a1a5344ddbe8 ("tcp: avoid two atomic ops for syncookies"),
reqsk->rsk_listener could be NULL when SYN Cookie is returned to its
client, as hinted by the leading SYN Cookie log.
Here are 3 options to fix the bug:
1) Return 0 in calipso_req_setattr()
2) Return an error in calipso_req_setattr()
3) Alaways set rsk_listener
1) is no go as it bypasses LSM, but 2) effectively disables SYN Cookie
for CALIPSO. 3) is also no go as there have been many efforts to reduce
atomic ops and make TCP robust against DDoS. See also commit 3b24d854cb35
("tcp/dccp: do not touch listener sk_refcnt under synflood").
As of the blamed commit, SYN Cookie already did not need refcounting,
and no one has stumbled on the bug for 9 years, so no CALIPSO user will
care about SYN Cookie.
Let's return an error in calipso_req_setattr() and calipso_req_delattr()
in the SYN Cookie case.
This can be reproduced by [1] on Fedora and now connect() of nc times out.
Fixes: e1adea927080 ("calipso: Allow request sockets to be relabelled by the lsm.") Reported-by: syzkaller <syzkaller@googlegroups.com> Reported-by: John Cheung <john.cs.hey@gmail.com> Closes: https://lore.kernel.org/netdev/CAP=Rh=MvfhrGADy+-WJiftV2_WzMH4VEhEFmeT28qY+4yxNu4w@mail.gmail.com/ Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com> Acked-by: Paul Moore <paul@paul-moore.com> Link: https://patch.msgid.link/20250617224125.17299-1-kuni1840@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Shannon Nelson [Mon, 16 Jun 2025 22:44:37 +0000 (15:44 -0700)]
MAINTAINERS: Remove Shannon Nelson from MAINTAINERS file
Brett Creeley is taking ownership of AMD/Pensando drivers while I wander
off into the sunset with my retirement this month. I'll still keep an
eye out on a few topics for awhile, and maybe do some free-lance work in
the future.
Meanwhile, thank you all for the fun and support and the many learning
opportunities :-).
Special thanks go to DaveM for merging my first patch long ago, the big
ionic patchset a few years ago, and my last patchset last week.
All 10 patches are by Geert Uytterhoeven, target the rcar_canfd
driver, first cleanup/refactor the driver and then add support for
Transceiver Delay Compensation.
* tag 'linux-can-next-for-6.17-20250618' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: rcar_canfd: Add support for Transceiver Delay Compensation
can: rcar_canfd: Return early in rcar_canfd_set_bittiming() when not FD
can: rcar_canfd: Share config code in rcar_canfd_set_bittiming()
can: rcar_canfd: Rename rcar_canfd_setrnc() to rcar_canfd_set_rnc()
can: rcar_canfd: Repurpose f_dcfg base for other registers
can: rcar_canfd: Simplify data access in rcar_canfd_{ge,pu}t_data()
can: rcar_canfd: Add helper variable dev to rcar_canfd_reset_controller()
can: rcar_canfd: Add helper variable ndev to rcar_canfd_rx_pkt()
can: rcar_canfd: Remove bittiming debug prints
can: rcar_canfd: Consistently use ndev for net_device pointers
====================
Alexey Kodanev [Mon, 16 Jun 2025 11:37:43 +0000 (11:37 +0000)]
net: lan743x: fix potential out-of-bounds write in lan743x_ptp_io_event_clock_get()
Before calling lan743x_ptp_io_event_clock_get(), the 'channel' value
is checked against the maximum value of PCI11X1X_PTP_IO_MAX_CHANNELS(8).
This seems correct and aligns with the PTP interrupt status register
(PTP_INT_STS) specifications.
However, lan743x_ptp_io_event_clock_get() writes to ptp->extts[] with
only LAN743X_PTP_N_EXTTS(4) elements, using channel as an index:
====================
selftests: net: use slowwait to make sure setup finished
The two updated tests sometimes failed because the network setup hadn't
completed. Used slowwait to ensure the setup finished and the tests
always passed. I ran both tests 50 times, and all of them passed.
====================
Hangbin Liu [Tue, 17 Jun 2025 10:50:59 +0000 (10:50 +0000)]
selftests: net: use slowwait to stabilize vrf_route_leaking test
The vrf_route_leaking test occasionally fails due to connectivity issues
in our testing environment. A sample failure message shows that the ping
check fails intermittently
PING 2001:db8:16:2::2 (2001:db8:16:2::2) 56 data bytes
This is likely due to insufficient wait time on slower machines. To address
this, switch to using slowwait, which provides a longer and more reliable
wait for setup completion.
Before this change, the test failed 3 out of 10 times. After applying this
fix, the test was run 30 times without any failure.
====================
Support bandwidth clamping in mana using net shapers
This patchset introduces hardware-backed bandwidth rate limiting
for MANA NICs via the net_shaper_ops interface, enabling efficient and
fine-grained traffic shaping directly on the device.
Previously, MANA lacked a mechanism for user-configurable bandwidth
control. With this addition, users can now configure shaping parameters,
allowing better traffic management and performance isolation.
The implementation includes the net_shaper_ops callbacks in the MANA
driver and supports one shaper per vport. Add shaping support via
mana_set_bw_clamp(), allowing the configuration of bandwidth rates
in 100 Mbps increments (minimum 100 Mbps). The driver validates input
and rejects unsupported values. On failure, it restores the previous
configuration which is queried using mana_query_link_cfg() or
retains the current state.
To prevent potential deadlocks introduced by net_shaper_ops, switch to
_locked variants of NAPI APIs when netdevops_lock is held during
VF setup and teardown.
Also, Add support for ethtool get_link_ksettings to report the maximum
link speed supported by the SKU in mbps.
These APIs when invoked on hardware that are older or that do
not support these APIs, the speed would be reported as UNKNOWN and
the net-shaper calls to set speed would fail.
====================
If any of the HWC commands are not recognized by the
underlying hardware, the hardware returns the response
header status of -1. Log the information using
netdev_info_once to avoid multiple error logs in dmesg.
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com> Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com> Reviewed-by: Dipayaan Roy <dipayanroy@linux.microsoft.com> Link: https://patch.msgid.link/1750144656-2021-5-git-send-email-ernis@linux.microsoft.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
net: mana: Add speed support in mana_get_link_ksettings
Allow mana ethtool get_link_ksettings operation to report
the maximum speed supported by the SKU in mbps.
The driver retrieves this information by issuing a
HWC command to the hardware via mana_query_link_cfg(),
which retrieves the SKU's maximum supported speed.
These APIs when invoked on hardware that are older/do
not support these APIs, the speed would be reported as UNKNOWN.
Before:
$ethtool enP30832s1
> Settings for enP30832s1:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: yes
After:
$ethtool enP30832s1
> Settings for enP30832s1:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 16000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: yes
Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com> Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Link: https://patch.msgid.link/1750144656-2021-4-git-send-email-ernis@linux.microsoft.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Introduce support for net_shaper_ops in the MANA driver,
enabling configuration of rate limiting on the MANA NIC.
To apply rate limiting, the driver issues a HWC command via
mana_set_bw_clamp() and updates the corresponding shaper object
in the net_shaper cache. If an error occurs during this process,
the driver restores the previous speed by querying the current link
configuration using mana_query_link_cfg().
The minimum supported bandwidth is 100 Mbps, and only values that are
exact multiples of 100 Mbps are allowed. Any other values are rejected.
To remove a shaper, the driver resets the bandwidth to the maximum
supported by the SKU using mana_set_bw_clamp() and clears the
associated cache entry. If an error occurs during this process,
the shaper details are retained.
On the hardware that does not support these APIs, the net-shaper
calls to set speed would fail.
Set the speed:
./tools/net/ynl/pyynl/cli.py \
--spec Documentation/netlink/specs/net_shaper.yaml \
--do set --json '{"ifindex":'$IFINDEX',
"handle":{"scope": "netdev", "id":'$ID' },
"bw-max": 200000000 }'
Get the shaper details:
./tools/net/ynl/pyynl/cli.py \
--spec Documentation/netlink/specs/net_shaper.yaml \
--do get --json '{"ifindex":'$IFINDEX',
"handle":{"scope": "netdev", "id":'$ID' }}'
net: mana: Fix potential deadlocks in mana napi ops
When net_shaper_ops are enabled for MANA, netdev_ops_lock
becomes active.
MANA VF setup/teardown by netvsc follows this call chain:
netvsc_vf_setup()
dev_change_flags()
...
__dev_open() OR __dev_close()
dev_change_flags() holds the netdev mutex via netdev_lock_ops.
Meanwhile, mana_create_txq() and mana_create_rxq() in mana_open()
path call NAPI APIs (netif_napi_add_tx(), netif_napi_add_weight(),
napi_enable()), which also try to acquire the same lock, risking
deadlock.
Similarly in the teardown path (mana_close()), netif_napi_disable()
and netif_napi_del(), contend for the same lock.
Switch to the _locked variants of these APIs to avoid deadlocks
when the netdev_ops_lock is held.
Fixes: d4c22ec680c8 ("net: hold netdev instance lock during ndo_open/ndo_stop") Signed-off-by: Erni Sri Satya Vennela <ernis@linux.microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com> Reviewed-by: Saurabh Singh Sengar <ssengar@linux.microsoft.com> Reviewed-by: Long Li <longli@microsoft.com> Link: https://patch.msgid.link/1750144656-2021-2-git-send-email-ernis@linux.microsoft.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Guillaume Nault [Mon, 16 Jun 2025 11:58:29 +0000 (13:58 +0200)]
ipv6: Simplify link-local address generation for IPv6 GRE.
Since commit 3e6a0243ff00 ("gre: Fix again IPv6 link-local address
generation."), addrconf_gre_config() has stopped handling IP6GRE
devices specially and just calls the regular addrconf_addr_gen()
function to create their link-local IPv6 addresses.
We can thus avoid using addrconf_gre_config() for IP6GRE devices and
use the normal IPv6 initialisation path instead (that is, jump directly
to addrconf_dev_config() in addrconf_init_auto_addrs()).
See commit 3e6a0243ff00 ("gre: Fix again IPv6 link-local address
generation.") for a deeper explanation on how and why GRE devices
started handling their IPv6 link-local address generation specially,
why it was a problem, and why this is not even necessary in most cases
(especially for GRE over IPv6).
====================
Add support for PSE budget evaluation strategy
This series brings support for budget evaluation strategy in the PSE
subsystem. PSE controllers can set priorities to decide which ports should
be turned off in case of special events like over-current.
This patch series adds support for two budget evaluation strategy.
1. Static Method:
This method involves distributing power based on PD classification.
It’s straightforward and stable, the PSE core keeping track of the
budget and subtracting the power requested by each PD’s class.
Advantages: Every PD gets its promised power at any time, which
guarantees reliability.
Disadvantages: PD classification steps are large, meaning devices
request much more power than they actually need. As a result, the power
supply may only operate at, say, 50% capacity, which is inefficient and
wastes money.
2. Dynamic Method:
To address the inefficiencies of the static method, vendors like
Microchip have introduced dynamic power budgeting, as seen in the
PD692x0 firmware. This method monitors the current consumption per port
and subtracts it from the available power budget. When the budget is
exceeded, lower-priority ports are shut down.
Advantages: This method optimizes resource utilization, saving costs.
Disadvantages: Low-priority devices may experience instability.
The UAPI allows adding support for software port priority mode managed from
userspace later if needed.
Patches 1-2: Add support for interrupt event report in PSE core, ethtool
and ethtool specs.
Patch 3: Adds support for interrupt and event report in TPS23881 driver.
Patches 4,5: Add support for PSE power domain in PSE core and ethtool.
Patches 6-8: Add support for budget evaluation strategy in PSE core,
ethtool and ethtool specs.
Patches 9-11: Add support for port priority and power supplies in PD692x0
drivers.
Patches 12,13: Add support for port priority in TPS23881 drivers.
====================
Add an interrupt property to the device tree bindings for the TI TPS23881
PSE controller. The interrupt is primarily used to detect classification
and disconnection events, which are essential for managing the PSE
controller in compliance with the PoE standard.
Interrupt support is essential for the proper functioning of the TPS23881
controller. Without it, after a power-on (PWON), the controller will
no longer perform detection and classification. This could lead to
potential hazards, such as connecting a non-PoE device after a PoE device,
which might result in magic smoke.
net: pse-pd: tps23881: Add support for static port priority feature
This patch enhances PSE callbacks by introducing support for the static
port priority feature. It extends interrupt management to handle and report
detection, classification, and disconnection events. Additionally, it
introduces the pi_get_pw_req() callback, which provides information about
the power requested by the Powered Devices.
Interrupt support is essential for the proper functioning of the TPS23881
controller. Without it, after a power-on (PWON), the controller will
no longer perform detection and classification. This could lead to
potential hazards, such as connecting a non-PoE device after a PoE device,
which might result in magic smoke.
Adds the regulator supply parameter of the managers.
Update also the example as the regulator supply of the PSE PIs
should be the managers itself and not an external regulator.
net: pse-pd: pd692x0: Add support for controller and manager power supplies
Add support for managing the VDD and VDDA power supplies for the PD692x0
PSE controller, as well as the VAUX5 and VAUX3P3 power supplies for the
PD6920x PSE managers.
net: pse-pd: pd692x0: Add support for PSE PI priority feature
This patch extends the PSE callbacks by adding support for the newly
introduced pi_set_prio() callback, enabling the configuration of PSE PI
priorities. The current port priority is now also included in the status
information returned to users.
net: ethtool: Add PSE port priority support feature
This patch expands the status information provided by ethtool for PSE c33
with current port priority and max port priority. It also adds a call to
pse_ethtool_set_prio() to configure the PSE port priority.
net: pse-pd: Add support for budget evaluation strategies
This patch introduces the ability to configure the PSE PI budget evaluation
strategies. Budget evaluation strategies is utilized by PSE controllers to
determine which ports to turn off first in scenarios such as power budget
exceedance.
The pis_prio_max value is used to define the maximum priority level
supported by the controller. Both the current priority and the maximum
priority are exposed to the user through the pse_ethtool_get_status call.
This patch add support for two mode of budget evaluation strategies.
1. Static Method:
This method involves distributing power based on PD classification.
It’s straightforward and stable, the PSE core keeping track of the
budget and subtracting the power requested by each PD’s class.
Advantages: Every PD gets its promised power at any time, which
guarantees reliability.
Disadvantages: PD classification steps are large, meaning devices
request much more power than they actually need. As a result, the power
supply may only operate at, say, 50% capacity, which is inefficient and
wastes money.
Priority max value is matching the number of PSE PIs within the PSE.
2. Dynamic Method:
To address the inefficiencies of the static method, vendors like
Microchip have introduced dynamic power budgeting, as seen in the
PD692x0 firmware. This method monitors the current consumption per port
and subtracts it from the available power budget. When the budget is
exceeded, lower-priority ports are shut down.
Advantages: This method optimizes resource utilization, saving costs.
Disadvantages: Low-priority devices may experience instability.
Priority max value is set by the PSE controller driver.
For now, budget evaluation methods are not configurable and cannot be
mixed. They are hardcoded in the PSE driver itself, as no current PSE
controller supports both methods.
Introduce PSE power domain support as groundwork for upcoming port
priority features. Multiple PSE PIs can now be grouped under a single
PSE power domain, enabling future enhancements like defining available
power budgets, port priority modes, and disconnection policies. This
setup will allow the system to assess whether activating a port would
exceed the available power budget, preventing over-budget states
proactively.
net: pse-pd: tps23881: Add support for PSE events and interrupts
Add support for PSE event reporting through interrupts. Set up the newly
introduced devm_pse_irq_helper helper to register the interrupt. Events are
reported for over-current and over-temperature conditions.
Add support for devm_pse_irq_helper() to register PSE interrupts and report
events such as over-current or over-temperature conditions. This follows a
similar approach to the regulator API but also sends notifications using a
dedicated PSE ethtool netlink socket.
net: pse-pd: Introduce attached_phydev to pse control
In preparation for reporting PSE events via ethtool notifications,
introduce an attached_phydev field in the pse_control structure.
This field stores the phy_device associated with the PSE PI,
ensuring that notifications are sent to the correct network
interface.
The attached_phydev pointer is directly tied to the PHY lifecycle. It
is set when the PHY is registered and cleared when the PHY is removed.
There is no need to use a refcount, as doing so could interfere with
the PHY removal process.
Jakub Kicinski [Thu, 19 Jun 2025 01:57:32 +0000 (18:57 -0700)]
Merge branch 'phc-support-in-ena-driver'
David Arinzon says:
====================
PHC support in ENA driver
This patchset adds the support for PHC (PTP Hardware Clock)
in the ENA driver. The documentation part of the patchset
includes additional information, including statistics,
utilization and invocation examples through the testptp
utility.
====================
David Arinzon [Tue, 17 Jun 2025 11:05:42 +0000 (14:05 +0300)]
net: ena: Control PHC enable through devlink
Add the capability to set parameters through the devlink framework.
The parameter used for controlling PHC (enable/disable) details
are as follows:
- Name: enable_phc
- Type: Boolean (true - enable/false - disable)
- Mode: DEVLINK_PARAM_CMODE_DRIVERINIT
- Effect: Changes take place during driver initialization,
any changes require a devlink reload to take effect.
David Arinzon [Tue, 17 Jun 2025 11:05:39 +0000 (14:05 +0300)]
net: ena: Add device reload capability through devlink
Adding basic devlink capability support of reloading the driver.
This capability is required to support driver init type
devlink params (DEVLINK_PARAM_CMODE_DRIVERINIT). Such params
require reloading of the driver (destroy/restore sequence).
The reloading is done by the devlink framework using the
hooks provided by the driver.
David Arinzon [Tue, 17 Jun 2025 11:05:38 +0000 (14:05 +0300)]
net: ena: PHC silent reset
Each PHC device kernel registration receives a unique kernel index,
which is associated with a new PHC device file located at
"/dev/ptp<index>".
This device file serves as an interface for obtaining PHC timestamps.
Examples of tools that use "/dev/ptp" include testptp [1]
and chrony [2].
A reset flow may occur in the ENA driver while PHC is active.
During a reset, the driver will unregister and then re-register the
PHC device with the kernel.
Under race conditions, particularly during heavy PHC loads,
the driver’s reset flow might complete faster than the kernel’s PHC
unregister/register process.
This can result in the PHC index being different from what it was prior
to the reset, as the PHC index is selected using kernel ID
allocation [3].
While driver rmmod/insmod are done by the user, a reset may occur
at anytime, without the user awareness, consequently, the driver
might receive a new PHC index after the reset, potentially compromising
the user experience.
To prevent this issue, the PHC flow will detect the reset during PHC
destruction and will skip the PHC unregister/register calls to preserve
the kernel PHC index.
During the reset flow, any attempt to get a PHC timestamp will fail as
expected, but the kernel PHC index will remain unchanged.
David Arinzon [Tue, 17 Jun 2025 11:05:37 +0000 (14:05 +0300)]
net: ena: Add PHC support in the ENA driver
The ENA driver will be extended to support the new PHC feature using
ptp_clock interface [1]. this will provide timestamp reference for user
space to allow measuring time offset between the PHC and the system
clock in order to achieve nanosecond accuracy.
Recently bnxt had to grow back a bunch of rtnl dependencies because
of udp_tunnel's infra. Add separate (global) mutext to protect
udp_tunnel state.
====================
udp_tunnel infra doesn't need RTNL, should be safe to get back
to only netdev instance lock.
Cc: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com> Link: https://patch.msgid.link/20250616162117.287806-7-stfomichev@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that there is only one path in udp_tunnel, there is no need to
have udp_ports_sleep knob. Remove it and adjust the test.
Cc: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com> Link: https://patch.msgid.link/20250616162117.287806-6-stfomichev@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net: remove redundant ASSERT_RTNL() in queue setup functions
The existing netdev_ops_assert_locked() already asserts that either
the RTNL lock or the per-device lock is held, making the explicit
ASSERT_RTNL() redundant.
Drivers that are using ops lock and don't depend on RTNL lock
still need to manage it because udp_tunnel's RTNL dependency.
Introduce new udp_tunnel_nic_lock and use it instead of
rtnl_lock. Drop non-UDP_TUNNEL_NIC_INFO_MAY_SLEEP mode from
udp_tunnel infra (udp_tunnel_nic_device_sync_work needs to
grab udp_tunnel_nic_lock mutex and might sleep).
We won't be able to sleep soon in vxlan_offload_rx_ports and won't be
able to grab sock_lock. Instead of having separate spinlock to
manage sockets, rely on rtnl lock. This is similar to how geneve
manages its sockets.
Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://patch.msgid.link/20250616162117.287806-3-stfomichev@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
geneve: rely on rtnl lock in geneve_offload_rx_ports
udp_tunnel_push_rx_port will grab mutex in the next patch so
we can't use rcu. geneve_offload_rx_ports is called
from geneve_netdevice_event for NETDEV_UDP_TUNNEL_PUSH_INFO and
NETDEV_UDP_TUNNEL_DROP_INFO which both have ASSERT_RTNL.
Entries are added to and removed from the sock_list under rtnl
lock as well (when adding or removing a tunneling device).
====================
net: fix passive TFO socket having invalid NAPI ID
Found a bug where an accepted passive TFO socket returns an invalid NAPI
ID (i.e. 0) from SO_INCOMING_NAPI_ID. Add a selftest for this using
netdevsim and fix the bug.
Patch 1 is a drive-by fix for the lib.sh include in an existing
drivers/net/netdevsim/peer.sh selftest.
Patch 2 adds a test binary for a simple TFO server/client.
Patch 3 adds a selftest for checking that the NAPI ID of a passive TFO
socket is valid. This will currently fail.
Patch 4 adds a fix for the bug.
====================
David Wei [Tue, 17 Jun 2025 21:21:02 +0000 (14:21 -0700)]
tcp: fix passive TFO socket having invalid NAPI ID
There is a bug with passive TFO sockets returning an invalid NAPI ID 0
from SO_INCOMING_NAPI_ID. Normally this is not an issue, but zero copy
receive relies on a correct NAPI ID to process sockets on the right
queue.
Fix by adding a sk_mark_napi_id_set().
Fixes: e5907459ce7e ("tcp: Record Rx hash and NAPI ID in tcp_child_process") Signed-off-by: David Wei <dw@davidwei.uk> Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://patch.msgid.link/20250617212102.175711-5-dw@davidwei.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Mon, 16 Jun 2025 21:24:05 +0000 (23:24 +0200)]
dpaa_eth: don't use fixed_phy_change_carrier
This effectively reverts 6e8b0ff1ba4c ("dpaa_eth: Add change_carrier()
for Fixed PHYs"). Usage of fixed_phy_change_carrier() requires that
fixed_phy_register() has been called before, directly or indirectly.
And that's not the case in this driver.
Linus Torvalds [Thu, 19 Jun 2025 00:47:27 +0000 (17:47 -0700)]
Merge tag '6.16-rc2-ksmbd-server-fixes' of git://git.samba.org/ksmbd
Pull smb server fixes from Steve French:
- Fix alternate data streams bug
- Important fix for null pointer deref with Kerberos authentication
- Fix oops in smbdirect (RDMA) in free_transport
* tag '6.16-rc2-ksmbd-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: handle set/get info file for streamed file
ksmbd: fix null pointer dereference in destroy_previous_session
ksmbd: add free_transport ops in ksmbd connection
Linus Torvalds [Wed, 18 Jun 2025 21:31:16 +0000 (14:31 -0700)]
Merge tag 'driver-core-6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core
Pull driver core fixes from Danilo Krummrich:
- Fix a race condition in Devres::drop(). This depends on two other
patches:
- (Minimal) Rust abstractions for struct completion
- Let Revocable indicate whether its data is already being revoked
- Fix Devres to avoid exposing the internal Revocable
- Add .mailmap entry for Danilo Krummrich
- Add Madhavan Srinivasan to embargoed-hardware-issues.rst
* tag 'driver-core-6.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/driver-core/driver-core:
Documentation: embargoed-hardware-issues.rst: Add myself for Power
mailmap: add entry for Danilo Krummrich
rust: devres: do not dereference to the internal Revocable
rust: devres: fix race in Devres::drop()
rust: revocable: indicate whether `data` has been revoked already
rust: completion: implement initial abstraction
Linus Torvalds [Wed, 18 Jun 2025 21:25:50 +0000 (14:25 -0700)]
Merge tag 'cgroup-for-6.16-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fix from Tejun Heo:
- In cgroup1 freezer, a task migrating into a frozen cgroup might not
get frozen immediately due to the wrong operation order. Fix it.
* tag 'cgroup-for-6.16-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup,freezer: fix incomplete freezing when attaching tasks
Linus Torvalds [Wed, 18 Jun 2025 21:22:31 +0000 (14:22 -0700)]
Merge tag 'wq-for-6.16-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue fix from Tejun Heo:
- Fix missed early init of wq_isolated_cpumask
* tag 'wq-for-6.16-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Initialize wq_isolated_cpumask in workqueue_init_early()
Each link supports multiple channels for example RPM link supports
16 channels. In case of link oversubsribe, NIX will assert backpressure
on receive channels.
The previous patch considered a single channel per link, resulting in
backpressure not being enabled on the remaining channels
Fixes: a7ef63dbd588 ("octeontx2-af: Disable backpressure between CPT and NIX") Signed-off-by: Hariprasad Kelam <hkelam@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://patch.msgid.link/20250617063403.3582210-1-hkelam@marvell.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Excluding the case where nla is exactly -NLA_HDRLEN, it will not return
NULL. And it seems misleading to assume that it can, other than in this
corner case. So drop checks for this condition.
Linus Torvalds [Wed, 18 Jun 2025 21:17:15 +0000 (14:17 -0700)]
Merge tag 'sched_ext-for-6.16-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fixes from Tejun Heo:
- Fix a couple bugs in cgroup cpu.weight support
- Add the new sched-ext@lists.linux.dev to MAINTAINERS
* tag 'sched_ext-for-6.16-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext, sched/core: Don't call scx_group_set_weight() prematurely from sched_create_group()
sched_ext: Make scx_group_set_weight() always update tg->scx.weight
sched_ext: Update mailing list entry in MAINTAINERS
Jakub Kicinski [Wed, 18 Jun 2025 21:15:15 +0000 (14:15 -0700)]
Merge branch '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2025-06-17 (ice, e1000e)
For ice:
Krishna Kumar modifies aRFS match criteria to correctly identify
matching filters.
Grzegorz fixes a memory leak in eswitch legacy mode.
For e1000e:
Vitaly sets clock frequency on some Nahum systems which may misreport
their value.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: set fixed clock frequency indication for Nahum 11 and Nahum 13
ice: fix eswitch code memory leak in reset scenario
net: ice: Perform accurate aRFS flow match
====================
Heiner Kallweit [Tue, 17 Jun 2025 18:20:17 +0000 (20:20 +0200)]
net: ftgmac100: select FIXED_PHY
Depending on e.g. DT configuration this driver uses a fixed link.
So we shouldn't rely on the user to enable FIXED_PHY, select it in
Kconfig instead. We may end up with a non-functional driver otherwise.
Jakub Kicinski [Tue, 17 Jun 2025 20:22:40 +0000 (13:22 -0700)]
net: ethtool: remove duplicate defines for family info
Commit under fixes switched to uAPI generation from the YAML
spec. A number of custom defines were left behind, mostly
for commands very hard to express in YAML spec.
Among what was left behind was the name and version of
the generic netlink family. Problem is that the codegen
always outputs those values so we ended up with a duplicated,
differently named set of defines.
Provide naming info in YAML and remove the incorrect defines.
Linus Torvalds [Wed, 18 Jun 2025 21:09:22 +0000 (14:09 -0700)]
Merge tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull crypto library fixes from Eric Biggers:
- Fix a regression in the arm64 Poly1305 code
- Fix a couple compiler warnings
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
lib/crypto/poly1305: Fix arm64's poly1305_blocks_arch()
lib/crypto/curve25519-hacl64: Disable KASAN with clang-17 and older
lib/crypto: Annotate crypto strings with nonstring
projects / thirdparty / linux.git / log
