The driver does not implement non-continuous clock mode, so the actual
value doesn't make a practical difference yet. However this change also
ensures that the value does not write to reserved registers bits in case
of under/overflow.
This register must be set to a value that ensures that
TCLK-TRAIL > 60ns
and
TEOT <= (105 ns + 12 x UI)
with the actual value of TCLK-TRAIL being
(TCLK_TRAILCNT + (1 to 2)) xHSByteClkCycle +
(2 + (1 to 2)) * HSBYTECLKCycle - (PHY output delay)
with PHY output delay being about
(2 to 3) x MIPIBitClk cycle in the BitClk conversion.
Add atomic_get_input_bus_fmts() implementation, tc358768 has a parallel
RGB input interface with the actual bus format depending on the amount
of parallel input data lines.
Without this change when the tc358768 is used with less than 24bit the
color mapping is completely wrong.
Correctly compute the PLL target frequency, the current formula works
correctly only when the input bus width is 24bit, actually to properly
compute the PLL target frequency what is relevant is the bits-per-pixel
on the DSI link.
No regression expected since the DSI format is currently hard-coded as
MIPI_DSI_FMT_RGB888.
Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
The watchdog_timer can schedule tx_timeout_task and watchdog_work
can also arm watchdog_timer. The process is shown below:
----------- timer schedules work ------------
cyttsp4_watchdog_timer() //timer handler
schedule_work(&cd->watchdog_work)
----------- work arms timer ------------
cyttsp4_watchdog_work() //workqueue callback function
cyttsp4_start_wd_timer()
mod_timer(&cd->watchdog_timer, ...)
Although del_timer_sync() and cancel_work_sync() are called in
cyttsp4_remove(), the timer and workqueue could still be rearmed.
As a result, the possible use after free bugs could happen. The
process is shown below:
The address of a data structure member was determined before
a corresponding null pointer check in the implementation of
the function “receive_timing_debugfs_show”.
Thus avoid the risk for undefined behaviour by moving the assignment
for the variable “vid” behind the null pointer check.
This issue was detected by using the Coccinelle software.
SLPC enables use of efficient freq at init by default. It is
possible for GuC to request frequencies that are higher than
the 'software' max if user has set it lower than the efficient
level.
Scenarios/tests that require strict fixing of freq below the efficient
level will need to disable it through this interface.
v2: Keep just one interface to toggle sysfs. With this, user will
be completely responsible for toggling efficient frequency if need
be. There will be no implicit disabling when user sets min < RP1 (Ashutosh)
commit dd0ff4d12dd2 ("bootmem: remove the vmemmap pages from kmemleak in
put_page_bootmem") fix an overlaps existing problem of kmemleak. But the
problem still existed when HAVE_BOOTMEM_INFO_NODE is disabled, because in
this case, free_bootmem_page() will call free_reserved_page() directly.
Fix the problem by adding kmemleak_free_part() in free_bootmem_page() when
HAVE_BOOTMEM_INFO_NODE is disabled.
Link: https://lkml.kernel.org/r/20230704101942.2819426-1-liushixin2@huawei.com Fixes: f41f2ed43ca5 ("mm: hugetlb: free the vmemmap pages associated with each HugeTLB page") Signed-off-by: Liu Shixin <liushixin2@huawei.com> Acked-by: Muchun Song <songmuchun@bytedance.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
The bit for flip addr is being set causing the determination for
FAST vs MEDIUM to always return MEDIUM when plane info is provided
as a surface update. This causes extreme stuttering for the typical
atomic update path on Linux.
[How]
Don't use update_flags->raw for determining FAST vs MEDIUM. It's too
fragile to changes like this.
Explicitly specify the update type per update flag instead. It's not
as clever as checking the bits itself but at least it's correct.
Fixes: aa5fdb1ab5b6 ("drm/amd/display: Explicitly specify update type per plane info change") Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Several calls to ci_dpm_fini() will attempt to free resources that
either have been freed before or haven't been allocated yet. This
may lead to undefined or dangerous behaviour.
For instance, if r600_parse_extended_power_table() fails, it might
call r600_free_extended_power_table() as will ci_dpm_fini() later
during error handling.
Fix this by only freeing pointers to objects previously allocated.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: cc8dbbb4f62a ("drm/radeon: add dpm support for CI dGPUs (v2)") Co-developed-by: Natalia Petrova <n.petrova@fintech.ru> Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a warning in __local_bh_enable_ip(). [0]
Commit 8d61f926d420 ("netlink: fix potential deadlock in
netlink_set_err()") converted read_lock(&nl_table_lock) to
read_lock_irqsave() in __netlink_diag_dump() to prevent a deadlock.
However, __netlink_diag_dump() calls sock_i_ino() that uses
read_lock_bh() and read_unlock_bh(). If CONFIG_TRACE_IRQFLAGS=y,
read_unlock_bh() finally enables IRQ even though it should stay
disabled until the following read_unlock_irqrestore().
Using read_lock() in sock_i_ino() would trigger a lockdep splat
in another place that was fixed in commit f064af1e500a ("net: fix
a lockdep splat"), so let's add __sock_i_ino() that would be safe
to use under BH disabled.
When using the felix driver (the only one which supports UC filtering
and MC filtering) as a DSA master for a random other DSA switch, one can
see the following stack trace when the downstream switch ports join a
VLAN-aware bridge:
What it's saying is that vlan_for_each() expects rtnl_lock() context and
it's not getting it, when it's called from the DSA master's ndo_set_rx_mode().
The caller of that - dsa_slave_set_rx_mode() - is the slave DSA
interface's dsa_port_bridge_host_fdb_add() which comes from the deferred
dsa_slave_switchdev_event_work().
We went to great lengths to avoid the rtnl_lock() context in that call
path in commit 0faf890fc519 ("net: dsa: drop rtnl_lock from
dsa_slave_switchdev_event_work"), and calling rtnl_lock() is simply not
an option due to the possibility of deadlocking when calling
dsa_flush_workqueue() from the call paths that do hold rtnl_lock() -
basically all of them.
So, when the DSA master calls vlan_for_each() from its ndo_set_rx_mode(),
the state of the 8021q driver on this device is really not protected
from concurrent access by anything.
Looking at net/8021q/, I don't think that vlan_info->vid_list was
particularly designed with RCU traversal in mind, so introducing an RCU
read-side form of vlan_for_each() - vlan_for_each_rcu() - won't be so
easy, and it also wouldn't be exactly what we need anyway.
In general I believe that the solution isn't in net/8021q/ anyway;
vlan_for_each() is not cut out for this task. DSA doesn't need rtnl_lock()
to be held per se - since it's not a netdev state change that we're
blocking, but rather, just concurrent additions/removals to a VLAN list.
We don't even need sleepable context - the callback of vlan_for_each()
just schedules deferred work.
The proposed escape is to remove the dependency on vlan_for_each() and
to open-code a non-sleepable, rtnl-free alternative to that, based on
copies of the VLAN list modified from .ndo_vlan_rx_add_vid() and
.ndo_vlan_rx_kill_vid().
Fixes: 64fdc5f341db ("net: dsa: sync unicast and multicast addresses for VLAN filters too") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20230626154402.3154454-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
ipvlan_queue_xmit() should return NET_XMIT_XXX, but
ipvlan_xmit_mode_l2/l3() returns rx_handler_result_t or NET_RX_XXX
in some cases. ipvlan_rcv_frame() will only return RX_HANDLER_CONSUMED
in ipvlan_xmit_mode_l2/l3() because 'local' is true. It's equal to
NET_XMIT_SUCCESS. But dev_forward_skb() can return NET_RX_SUCCESS or
NET_RX_DROP, and returning NET_RX_DROP(NET_XMIT_DROP) will increase
both ipvlan and ipvlan->phy_dev drops counter.
The skb to forward can be treated as xmitted successfully. This patch
makes ipvlan_queue_xmit() return NET_XMIT_SUCCESS for forward skb.
Fixes: 2ad7bf363841 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com> Link: https://lore.kernel.org/r/20230626093347.7492-1-cambda@linux.alibaba.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ct_sip_parse_numerical_param() returns only 0 or 1 now.
But process_register_request() and process_register_response() imply
checking for a negative value if parsing of a numerical header parameter
failed.
The invocation in nf_nat_sip() looks correct:
if (ct_sip_parse_numerical_param(...) > 0 &&
...) { ... }
Make the return value of the function ct_sip_parse_numerical_param()
a tristate to fix all the cases
a) return 1 if value is found; *val is set
b) return 0 if value is not found; *val is unchanged
c) return -1 on error; *val is undefined
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
And nothing more is 'pulled' from the packet, depending on the content.
dh->dccph_doff, and/or dh->dccph_x ...)
So dccp_ack_seq() is happily reading stuff past the _dh buffer.
BUG: KASAN: stack-out-of-bounds in nf_conntrack_dccp_packet+0x1134/0x11c0
Read of size 4 at addr ffff000128f66e0c by task syz-executor.2/29371
[..]
Fix this by increasing the stack buffer to also include room for
the extra sequence numbers and all the known dccp packet type headers,
then pull again after the initial validation of the basic header.
While at it, mark packets invalid that lack 48bit sequence bit but
where RFC says the type MUST use them.
Compile tested only.
v2: first skb_header_pointer() now needs to adjust the size to
only pull the generic header. (Eric)
Heads-up: I intend to remove dccp conntrack support later this year.
Fixes: 2bc780499aa3 ("[NETFILTER]: nf_conntrack: add DCCP protocol support") Reported-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Florian Westphal <fw@strlen.de> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The `shift` variable which indicates the offset in the string at which
to start matching the pattern is initialized to `bm->patlen - 1`, but it
is not reset when a new block is retrieved. This means the implemen-
tation may start looking at later and later positions in each successive
block and miss occurrences of the pattern at the beginning. E.g.,
consider a HTTP packet held in a non-linear skb, where the HTTP request
line occurs in the second block:
[... 52 bytes of packet headers ...]
GET /bmtest HTTP/1.1\r\nHost: www.example.com\r\n\r\n
and the pattern is "GET /bmtest".
Once the first block comprising the packet headers has been examined,
`shift` will be pointing to somewhere near the end of the block, and so
when the second block is examined the request line at the beginning will
be missed.
Reinitialize the variable for each new block.
Fixes: 8082e4ed0a61 ("[LIB]: Boyer-Moore extension for textsearch infrastructure strike #2") Link: https://bugzilla.netfilter.org/show_bug.cgi?id=1390 Signed-off-by: Jeremy Sowden <jeremy@azazel.net> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes several use-after-free that caused by function
nfc_llcp_find_local(). For example, one UAF can happen when below buggy
time window occurs.
The buggy address belongs to the object at ffff888105b0e400
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 16 bytes inside of
freed 1024-byte region [ffff888105b0e400, ffff888105b0e800)
Memory state around the buggy address: ffff888105b0e300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888105b0e380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff888105b0e400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff888105b0e480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff888105b0e500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
In summary, this patch solves those use-after-free by
1. Re-implement the nfc_llcp_find_local(). The current version does not
grab the reference when getting the local from the linked list. For
example, the llcp_sock_bind() gets the reference like below:
// llcp_sock_bind()
local = nfc_llcp_find_local(dev); // A
..... \
| raceable
..... /
llcp_sock->local = nfc_llcp_local_get(local); // B
There is an apparent race window that one can drop the reference
and free the local object fetched in (A) before (B) gets the reference.
2. Some callers of the nfc_llcp_find_local() do not grab the reference
at all. For example, the nfc_genl_llc_{{get/set}_params/sdreq} functions.
We add the nfc_llcp_local_put() for them. Moreover, we add the necessary
error handling function to put the reference.
3. Add the nfc_llcp_remove_local() helper. The local object is removed
from the linked list in local_release() when all reference is gone. This
patch removes it when nfc_llcp_unregister_device() is called.
Therefore, every caller of nfc_llcp_find_local() will get a reference
even when the nfc_llcp_unregister_device() is called. This promises no
use-after-free for the local object is ever possible.
Fixes: 52feb444a903 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support") Fixes: c7aa12252f51 ("NFC: Take a reference on the LLCP local pointer when creating a socket") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
efx_net_stats() (.ndo_get_stats64) can be called during an ethtool
selftest, during which time nic_data->mc_stats is NULL as the NIC has
been fini'd. In this case do not attempt to fetch the latest stats
from the hardware, else we will crash on a NULL dereference:
BUG: kernel NULL pointer dereference, address: 0000000000000038
RIP efx_nic_update_stats
abridged calltrace:
efx_ef10_update_stats_pf
efx_net_stats
dev_get_stats
dev_seq_printf_stats
Skipping the read is safe, we will simply give out stale stats.
To ensure that the free in efx_ef10_fini_nic() does not race against
efx_ef10_update_stats_pf(), which could cause a TOCTTOU bug, take the
efx->stats_lock in fini_nic (it is already held across update_stats).
Fixes: d3142c193dca ("sfc: refactor EF10 stats handling") Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com> Signed-off-by: Edward Cree <ecree.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
ocfs2 uses kzalloc() to allocate buffers for o2net_hand, o2net_keep_req and
o2net_keep_resp and then passes these to sendpage. This isn't really
allowed as the lifetime of slab objects is not controlled by page ref -
though in this case it will probably work. sendmsg() with MSG_SPLICE_PAGES
will, however, print a warning and give an error.
Fix it to use folio_alloc() instead to allocate a buffer for the handshake
message, keepalive request and reply messages.
Fixes: 98211489d414 ("[PATCH] OCFS2: The Second Oracle Cluster Filesystem") Signed-off-by: David Howells <dhowells@redhat.com>
cc: Mark Fasheh <mark@fasheh.com>
cc: Kurt Hackel <kurt.hackel@oracle.com>
cc: Joel Becker <jlbec@evilplan.org>
cc: Joseph Qi <joseph.qi@linux.alibaba.com>
cc: ocfs2-devel@oss.oracle.com Link: https://lore.kernel.org/r/20230623225513.2732256-14-dhowells@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
64-bit DMA detection will fail if axienet was started before (by boot
loader, boot ROM, etc). In this state axienet will not start properly.
XAXIDMA_TX_CDESC_OFFSET + 4 register (MM2S_CURDESC_MSB) is used to detect
64-bit DMA capability here. But datasheet says: When DMACR.RS is 1
(axienet is in enabled state), CURDESC_PTR becomes Read Only (RO) and
is used to fetch the first descriptor. So iowrite32()/ioread32() trick
to this register to detect 64-bit DMA will not work.
So move axienet reset before 64-bit DMA detection.
syzkaller reported use-after-free in __gtp_encap_destroy(). [0]
It shows the same process freed sk and touched it illegally.
Commit e198987e7dd7 ("gtp: fix suspicious RCU usage") added lock_sock()
and release_sock() in __gtp_encap_destroy() to protect sk->sk_user_data,
but release_sock() is called after sock_put() releases the last refcnt.
[0]:
BUG: KASAN: slab-use-after-free in instrument_atomic_read_write include/linux/instrumented.h:96 [inline]
BUG: KASAN: slab-use-after-free in atomic_try_cmpxchg_acquire include/linux/atomic/atomic-instrumented.h:541 [inline]
BUG: KASAN: slab-use-after-free in queued_spin_lock include/asm-generic/qspinlock.h:111 [inline]
BUG: KASAN: slab-use-after-free in do_raw_spin_lock include/linux/spinlock.h:186 [inline]
BUG: KASAN: slab-use-after-free in __raw_spin_lock_bh include/linux/spinlock_api_smp.h:127 [inline]
BUG: KASAN: slab-use-after-free in _raw_spin_lock_bh+0x75/0xe0 kernel/locking/spinlock.c:178
Write of size 4 at addr ffff88800dbef398 by task syz-executor.2/2401
The buggy address belongs to the object at ffff88800dbef300
which belongs to the cache UDPv6 of size 1344
The buggy address is located 152 bytes inside of
freed 1344-byte region [ffff88800dbef300, ffff88800dbef840)
Memory state around the buggy address: ffff88800dbef280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88800dbef300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88800dbef380: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff88800dbef400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88800dbef480: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
On systems where netdevsim is built-in or loaded before the test
starts, kci_test_ipsec_offload doesn't remove the netdevsim device it
created during the test.
Fixes: e05b2d141fef ("netdevsim: move netdev creation/destruction to dev probe") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/e1cb94f4f82f4eca4a444feec4488a1323396357.1687466906.git.sd@queasysnail.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syz-executor.2/23011 just changed the state of lock: ffffffff8e1a7a58 (nl_table_lock){.+.?}-{2:2}, at: netlink_set_err+0x2e/0x3a0 net/netlink/af_netlink.c:1612
but this lock was taken by another, SOFTIRQ-safe lock in the past:
(&local->queue_stop_reason_lock){..-.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
Commit 49725ffc15fc ("net: stmmac: power up/down serdes in
stmmac_open/release") correctly added a call to the serdes_powerdown()
callback to stmmac_release() but did not remove the one from
stmmac_remove() which leads to a doubled call to serdes_powerdown().
This can lead to all kinds of problems: in the case of the qcom ethqos
driver, it caused an unbalanced regulator disable splat.
Fixes: 49725ffc15fc ("net: stmmac: power up/down serdes in stmmac_open/release") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Acked-by: Junxiao Chang <junxiao.chang@intel.com> Reviewed-by: Andrew Halaney <ahalaney@redhat.com> Tested-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20230621135537.376649-1-brgl@bgdev.pl Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Stuff Bit Count is always coded on 4 bits [1]. Update the Stuff
Bit Count size accordingly.
In addition, the CRC fields of CAN FD Frames contain stuff bits at
fixed positions called fixed stuff bits [2]. The CRC field starts with
a fixed stuff bit and then has another fixed stuff bit after each
fourth bit [2], which allows us to derive this formula:
with len(CRC) either 17 or 21 bits depending of the payload length.
In conclusion, for CRC17:
FSB count = 1 + round_down((4 + 17)/4)
= 6
and for CRC 21:
FSB count = 1 + round_down((4 + 21)/4)
= 7
Add a Fixed Stuff bits (FSB) field with above values and update
CANFD_FRAME_OVERHEAD_SFF and CANFD_FRAME_OVERHEAD_EFF accordingly.
[1] ISO 11898-1:2015 section 10.4.2.6 "CRC field":
The CRC field shall contain the CRC sequence followed by a recessive
CRC delimiter. For FD Frames, the CRC field shall also contain the
stuff count.
Stuff count
If FD Frames, the stuff count shall be at the beginning of the CRC
field. It shall consist of the stuff bit count modulo 8 in a 3-bit
gray code followed by a parity bit [...]
[2] ISO 11898-1:2015 paragraph 10.5 "Frame coding":
In the CRC field of FD Frames, the stuff bits shall be inserted at
fixed positions; they are called fixed stuff bits. There shall be a
fixed stuff bit before the first bit of the stuff count, even if the
last bits of the preceding field are a sequence of five consecutive
bits of identical value, there shall be only the fixed stuff bit,
there shall not be two consecutive stuff bits. A further fixed stuff
bit shall be inserted after each fourth bit of the CRC field [...]
Fixes: 85d99c3e2a13 ("can: length: can_skb_get_frame_len(): introduce function to get data length of frame in data link layer") Suggested-by: Thomas Kopp <Thomas.Kopp@microchip.com> Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Reviewed-by: Thomas Kopp <Thomas.Kopp@microchip.com> Link: https://lore.kernel.org/all/20230611025728.450837-2-mailhol.vincent@wanadoo.fr Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When calling bpf_sk_lookup_tcp(), bpf_sk_lookup_udp() or
bpf_skc_lookup_tcp() from tc/xdp ingress, VRF socket bindings aren't
respoected, i.e. unbound sockets are returned, and bound sockets aren't
found.
VRF binding is determined by the sdif argument to sk_lookup(), however
when called from tc the IP SKB control block isn't initialized and thus
inet{,6}_sdif() always returns 0.
Fix by calculating sdif for the tc/xdp flows by observing the device's
l3 enslaved state.
The cg/sk_skb hooking points which are expected to support
inet{,6}_sdif() pass sdif=-1 which makes __bpf_skc_lookup() use the
existing logic.
Fixes: 6acc9b432e67 ("bpf: Add helper to retrieve socket in BPF") Signed-off-by: Gilad Sever <gilad9366@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Reviewed-by: Eyal Birger <eyal.birger@gmail.com> Acked-by: Stanislav Fomichev <sdf@google.com> Cc: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/bpf/20230621104211.301902-4-gilad9366@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Change BPF helper socket lookup functions to use TC specific variants:
bpf_tc_sk_lookup_tcp() / bpf_tc_sk_lookup_udp() / bpf_tc_skc_lookup_tcp()
instead of sharing implementation with the cg / sk_skb hooking points.
This allows introducing a separate logic for the TC flow.
The tc functions are identical to the original code.
Signed-off-by: Gilad Sever <gilad9366@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Reviewed-by: Eyal Birger <eyal.birger@gmail.com> Acked-by: Stanislav Fomichev <sdf@google.com> Link: https://lore.kernel.org/bpf/20230621104211.301902-2-gilad9366@gmail.com
Stable-dep-of: 9a5cb79762e0 ("bpf: Fix bpf socket lookup from tc/xdp to respect socket VRF bindings") Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 'ieee80211_queue_delayed_work()' expects timeout in
jiffies and not milliseconds, 'msecs_to_jiffies()' should
be used in 'ath_restart_work()' and '__ath9k_flush()'.
Fixes: d63ffc45c5d3 ("ath9k: rename tx_complete_work to hw_check_work") Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230613134655.248728-1-dmantipov@yandex.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
This microSD card never clears Flush Cache bit after cache flush has
been started in sd_flush_cache(). This leads e.g. to failure to mount
file system. Add a quirk which disables the SD cache for this specific
card from specific manufacturing date of 11/2019, since on newer dated
cards from 05/2023 the cache flush works correctly.
Fixes: 08ebf903af57 ("mmc: core: Fixup support for writeback-cache for eMMC and SD") Signed-off-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20230620102713.7701-1-marex@denx.de Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since regulatory disconnect was added, OCB and NAN interface
types were added, which made it completely unusable for any
driver that allowed OCB/NAN. Add OCB/NAN (though NAN doesn't
do anything, we don't have any info) and also remove all the
logic that opts out, so it won't be broken again if/when new
interface types are added.
The removed code ran for any BSS that was not included in the MBSSID
element in order to update it. However, instead of using the correct
inheritance rules, it would simply copy the elements from the
transmitting AP. The result is that we would report incorrect elements
in this case.
After some discussions, it seems that there are likely not even APs
actually using this feature. Either way, removing the code decreases
complexity and makes the cfg80211 behaviour more correct.
The cfg80211_gen_new_ie function merges the IEs using inheritance rules.
Rewrite this function to fix issues around inheritance rules. In
particular, vendor elements do not require any special handling, as they
are either all inherited or overridden by the subprofile.
Also, add fragmentation handling as this may be needed in some cases.
This also changes the function to not require making a copy. The new
version could be optimized a bit by explicitly tracking which IEs have
been handled already rather than looking that up again every time.
Note that a small behavioural change is the removal of the SSID special
handling. This should be fine for the MBSSID element, as the SSID must
be included in the subelement.
In mesh mode, ieee80211_chandef_he_6ghz_oper() is called by
mesh_matches_local() for every received mesh beacon.
On a 6 GHz mesh of a HE-only phy, this spams that the hardware does not
have EHT capabilities, even if the received mesh beacon does not have an
EHT element.
Unlike HE, not supporting EHT in the 6 GHz band is not an error so do
not print anything in this case.
Fixes: 5dca295dd767 ("mac80211: Add initial support for EHT and 320 MHz channels") Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230614132648.28995-1-nicolas.cavallari@green-communications.fr Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
rxq can be NULL only when trans_pcie->rxq is NULL and entry->entry
is zero. For the case when entry->entry is not equal to 0, rxq
won't be NULL even if trans_pcie->rxq is NULL. Modify checker to
check for trans_pcie->rxq.
Fixes: abc599efa67b ("iwlwifi: pcie: don't crash when rx queues aren't allocated in interrupt") Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com> Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Link: https://lore.kernel.org/r/20230614123446.5a5eb3889a4a.I375a1d58f16b48cd2044e7b7caddae512d7c86fd@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In mac80211, it's required that we pull from TXQs by calling
ieee80211_tx_dequeue() only with softirqs disabled. However,
in iwl_mvm_queue_state_change() we're often called with them
enabled, e.g. from flush if anything was flushed, triggering
a mac80211 warning.
Fix that by disabling the softirqs across the TX call.
During sending data after clients connected, hw_ops->get_ring_selector()
will be called. But for IPQ5018, this member isn't set, and the
following NULL pointer exception will be occurred:
[ 38.840478] 8<--- cut here ---
[ 38.840517] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 38.923161] PC is at 0x0
[ 38.927930] LR is at ath11k_dp_tx+0x70/0x730 [ath11k]
...
[ 39.063264] Process hostapd (pid: 1034, stack limit = 0x801ceb3d)
[ 39.068994] Stack: (0x856a9a68 to 0x856aa000)
...
[ 39.438467] [<7f323804>] (ath11k_dp_tx [ath11k]) from [<7f314e6c>] (ath11k_mac_op_tx+0x80/0x190 [ath11k])
[ 39.446607] [<7f314e6c>] (ath11k_mac_op_tx [ath11k]) from [<7f17dbe0>] (ieee80211_handle_wake_tx_queue+0x7c/0xc0 [mac80211])
[ 39.456162] [<7f17dbe0>] (ieee80211_handle_wake_tx_queue [mac80211]) from [<7f174450>] (ieee80211_probereq_get+0x584/0x704 [mac80211])
[ 39.467443] [<7f174450>] (ieee80211_probereq_get [mac80211]) from [<7f178c40>] (ieee80211_tx_prepare_skb+0x1f8/0x248 [mac80211])
[ 39.479334] [<7f178c40>] (ieee80211_tx_prepare_skb [mac80211]) from [<7f179e28>] (__ieee80211_subif_start_xmit+0x32c/0x3d4 [mac80211])
[ 39.491053] [<7f179e28>] (__ieee80211_subif_start_xmit [mac80211]) from [<7f17af08>] (ieee80211_tx_control_port+0x19c/0x288 [mac80211])
[ 39.502946] [<7f17af08>] (ieee80211_tx_control_port [mac80211]) from [<7f0fc704>] (nl80211_tx_control_port+0x174/0x1d4 [cfg80211])
[ 39.515017] [<7f0fc704>] (nl80211_tx_control_port [cfg80211]) from [<808ceac4>] (genl_rcv_msg+0x154/0x340)
[ 39.526814] [<808ceac4>] (genl_rcv_msg) from [<808cdb74>] (netlink_rcv_skb+0xb8/0x11c)
[ 39.536446] [<808cdb74>] (netlink_rcv_skb) from [<808ce1d0>] (genl_rcv+0x28/0x34)
[ 39.544344] [<808ce1d0>] (genl_rcv) from [<808cd234>] (netlink_unicast+0x174/0x274)
[ 39.551895] [<808cd234>] (netlink_unicast) from [<808cd510>] (netlink_sendmsg+0x1dc/0x440)
[ 39.559362] [<808cd510>] (netlink_sendmsg) from [<808596e0>] (____sys_sendmsg+0x1a8/0x1fc)
[ 39.567697] [<808596e0>] (____sys_sendmsg) from [<8085b1a8>] (___sys_sendmsg+0xa4/0xdc)
[ 39.575941] [<8085b1a8>] (___sys_sendmsg) from [<8085b310>] (sys_sendmsg+0x44/0x74)
[ 39.583841] [<8085b310>] (sys_sendmsg) from [<80300060>] (ret_fast_syscall+0x0/0x40)
...
[ 39.620734] Code: bad PC value
[ 39.625869] ---[ end trace 8aef983ad3cbc032 ]---
This filter already exists for excluding IPv6 SNMP stats. Extend its
definition to also exclude IFLA_VF_INFO stats in RTM_GETLINK.
This patch constitutes a partial fix for a netlink attribute nesting
overflow bug in IFLA_VFINFO_LIST. By excluding the stats when the
requester doesn't need them, the truncation of the VF list is avoided.
While it was technically only the stats added in commit c5a9f6f0ab40
("net/core: Add drop counters to VF statistics") breaking the camel's
back, the appreciable size of the stats data should never have been
included without due consideration for the maximum number of VFs
supported by PCI.
Fixes: 3b766cd83232 ("net/core: Add reading VF statistics through the PF netdevice") Fixes: c5a9f6f0ab40 ("net/core: Add drop counters to VF statistics") Signed-off-by: Edwin Peer <edwin.peer@broadcom.com> Cc: Edwin Peer <espeer@gmail.com> Signed-off-by: Gal Pressman <gal@nvidia.com> Link: https://lore.kernel.org/r/20230611105108.122586-1-gal@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On EDMA capable hardware, ath9k_txq_list_has_key() can enter infinite
loop if it is called while all txq_fifos have packets that use different
key that the one we are looking for. Fix it by exiting the loop if all
txq_fifos have been checked already.
Because this loop is called under spin_lock_bh() (see ath_txq_lock) it
causes the following rcu stall:
There are no other files referencing this function, apparently
it was left global to avoid an 'unused function' warning when
the only caller is left out. With a 'W=1' build, it causes
a 'missing prototype' warning though:
drivers/memstick/host/r592.c:47:13: error: no previous prototype for 'memstick_debug_get_tpc_name' [-Werror=missing-prototypes]
Annotate the function as 'static __maybe_unused' to avoid both
problems.
When I boot a kukui-kodama board, I see an ugly warning in my kernel
log:
mtk-msdc 11240000.mmc: error -ENXIO: IRQ sdio_wakeup not found
It's pretty normal not to have an "sdio_wakeup" IRQ defined. In fact,
no device trees in mainline seem to have it. Let's use the
platform_get_irq_byname_optional() to avoid the error message.
Fixes: 527f36f5efa4 ("mmc: mediatek: add support for SDIO eint wakup IRQ") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/r/20230510064434.1.I935404c5396e6bf952e99bb7ffb744c6f7fd430b@changeid Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "kexec: enable kexec_crash_size to support two crash kernel
regions".
When crashkernel=X fails to reserve region under 4G, it will fall back to
reserve region above 4G and a region of the default size will also be
reserved under 4G. Unfortunately, /sys/kernel/kexec_crash_size only
supports one crash kernel region now, the user cannot sense the low memory
reserved by reading /sys/kernel/kexec_crash_size. Also, low memory cannot
be freed by writing this file.
For example:
resource_size(crashk_res) = 512M
resource_size(crashk_low_res) = 256M
The result of 'cat /sys/kernel/kexec_crash_size' is 512M, but it should be
768M. When we execute 'echo 0 > /sys/kernel/kexec_crash_size', the size
of crashk_res becomes 0 and resource_size(crashk_low_res) is still 256 MB,
which is incorrect.
Since crashk_res manages the memory with high address and crashk_low_res
manages the memory with low address, crashk_low_res is shrunken only when
all crashk_res is shrunken. And because when there is only one crash
kernel region, crashk_res is always used. Therefore, if all crashk_res is
shrunken and crashk_low_res still exists, swap them.
This patch (of 6):
If the value of parameter 'new_size' is in the semi-open and semi-closed
interval (crashk_res.end - KEXEC_CRASH_MEM_ALIGN + 1, crashk_res.end], the
calculation result of ram_res is:
The operation of insert_resource() fails, and ram_res is not added to
iomem_resource. As a result, the memory of the control block ram_res is
leaked.
In fact, on all architectures, the start address and size of crashk_res
are already aligned by KEXEC_CRASH_MEM_ALIGN. Therefore, we do not need
to round up crashk_res.start again. Instead, we should round up
'new_size' in advance.
Link: https://lkml.kernel.org/r/20230527123439.772-1-thunder.leizhen@huawei.com Link: https://lkml.kernel.org/r/20230527123439.772-2-thunder.leizhen@huawei.com Fixes: 6480e5a09237 ("kdump: add missing RAM resource in crash_shrink_memory()") Fixes: 06a7f711246b ("kexec: premit reduction of the reserved memory size") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Cong Wang <amwang@redhat.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, in the watchdog_overflow_callback() we first check to see if
the watchdog had been touched and _then_ we handle the workaround for
turbo mode. This order should be reversed.
Specifically, "touching" the hardlockup detector's watchdog should avoid
lockups being detected for one period that should be roughly the same
regardless of whether we're running turbo or not. That means that we
should do the extra accounting for turbo _before_ we look at (and clear)
the global indicating that we've been touched.
NOTE: this fix is made based on code inspection. I am not aware of any
reports where the old code would have generated false positives. That
being said, this order seems more correct and also makes it easier down
the line to share code with the "buddy" hardlockup detector.
Link: https://lkml.kernel.org/r/20230519101840.v5.2.I843b0d1de3e096ba111a179f3adb16d576bef5c7@changeid Fixes: 7edaeb6841df ("kernel/watchdog: Prevent false positives with turbo modes") Signed-off-by: Douglas Anderson <dianders@chromium.org> Cc: Andi Kleen <ak@linux.intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Colin Cross <ccross@android.com> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Guenter Roeck <groeck@chromium.org> Cc: Ian Rogers <irogers@google.com> Cc: Lecopzer Chen <lecopzer.chen@mediatek.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masayoshi Mizuma <msys.mizuma@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Pingfan Liu <kernelfans@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Ricardo Neri <ricardo.neri@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Sumit Garg <sumit.garg@linaro.org> Cc: Tzung-Bi Shih <tzungbi@chromium.org> Cc: Will Deacon <will@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch series "watchdog/hardlockup: Add the buddy hardlockup detector", v5.
This patch series adds the "buddy" hardlockup detector. In brief, the
buddy hardlockup detector can detect hardlockups without arch-level
support by having CPUs checkup on a "buddy" CPU periodically.
Given the new design of this patch series, testing all combinations is
fairly difficult. I've attempted to make sure that all combinations of
CONFIG_ options are good, but it wouldn't surprise me if I missed
something. I apologize in advance and I'll do my best to fix any
problems that are found.
This patch (of 18):
The real watchdog_update_hrtimer_threshold() is defined in
kernel/watchdog_hld.c. That file is included if
CONFIG_HARDLOCKUP_DETECTOR_PERF and the function is defined in that file
if CONFIG_HARDLOCKUP_CHECK_TIMESTAMP.
The dummy version of the function in "nmi.h" didn't get that quite right.
While this doesn't appear to be a huge deal, it's nice to make it
consistent.
It doesn't break builds because CHECK_TIMESTAMP is only defined by x86 so
others don't get a double definition, and x86 uses perf lockup detector,
so it gets the out of line version.
Link: https://lkml.kernel.org/r/20230519101840.v5.18.Ia44852044cdcb074f387e80df6b45e892965d4a1@changeid Link: https://lkml.kernel.org/r/20230519101840.v5.1.I8cbb2f4fa740528fcfade4f5439b6cdcdd059251@changeid Fixes: 7edaeb6841df ("kernel/watchdog: Prevent false positives with turbo modes") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Petr Mladek <pmladek@suse.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Daniel Thompson <daniel.thompson@linaro.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Guenter Roeck <groeck@chromium.org> Cc: Ian Rogers <irogers@google.com> Cc: Lecopzer Chen <lecopzer.chen@mediatek.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Masayoshi Mizuma <msys.mizuma@gmail.com> Cc: Matthias Kaehlcke <mka@chromium.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Pingfan Liu <kernelfans@gmail.com> Cc: Randy Dunlap <rdunlap@infradead.org> Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com> Cc: Ricardo Neri <ricardo.neri@intel.com> Cc: Stephane Eranian <eranian@google.com> Cc: Stephen Boyd <swboyd@chromium.org> Cc: Sumit Garg <sumit.garg@linaro.org> Cc: Tzung-Bi Shih <tzungbi@chromium.org> Cc: Will Deacon <will@kernel.org> Cc: Colin Cross <ccross@android.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit f079a020ba95 ("selftests: memcg: factor out common parts of
memory.{low,min} tests"), the value used in second alloc_anon has changed
from 148M to 170M. Because memory.low allows reclaiming page cache in
child cgroups, so the memory.current is close to 30M instead of 50M.
Therefore, adjust the expected value of parent cgroup.
Link: https://lkml.kernel.org/r/20230522095233.4246-2-haifeng.xu@shopee.com Fixes: f079a020ba95 ("selftests: memcg: factor out common parts of memory.{low,min} tests") Signed-off-by: Haifeng Xu <haifeng.xu@shopee.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Michal Hocko <mhocko@kernel.org> Cc: Roman Gushchin <roman.gushchin@linux.dev> Cc: Shakeel Butt <shakeelb@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ice_ptp_extts_work() and ice_ptp_periodic_work() functions are both
scheduled on the same kthread worker, pf.ptp.kworker. The
ice_ptp_periodic_work() function sends to the firmware to interact with the
PHY, and must block to wait for responses.
This can cause delay in responding to the PFINT_OICR_TSYN_EVNT interrupt
cause, ultimately resulting in disruption to processing an input signal of
the frequency is high enough. In our testing, even 100 Hz signals get
disrupted.
Fix this by instead processing the signal inside the miscellaneous
interrupt thread prior to handling Tx timestamps.
Use atomic bits in a new pf->misc_thread bitmap in order to safely
communicate which tasks require processing within the
ice_misc_intr_thread_fn(). This ensures the communication of desired tasks
from the ice_misc_intr() are correctly processed without racing even in the
event that the interrupt triggers again before the thread function exits.
Fixes: 172db5f91d5f ("ice: add support for auxiliary input/output pins") Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It makes no sense to set MMC_PM_KEEP_POWER in shutdown. The flag
indicates to the MMC subsystem to keep the slot powered on during
suspend, but in shutdown the slot should actually be powered off.
Drop this call.
Fixes: 063848c3e155 ("rsi: sdio: Add WOWLAN support for S5 shutdown state") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230527222859.273768-1-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
In case WoWlan was never configured during the operation of the system,
the hw->wiphy->wowlan_config will be NULL. rsi_config_wowlan() checks
whether wowlan_config is non-NULL and if it is not, then WARNs about it.
The warning is valid, as during normal operation the rsi_config_wowlan()
should only ever be called with non-NULL wowlan_config. In shutdown this
rsi_config_wowlan() should only ever be called if WoWlan was configured
before by the user.
Add checks for non-NULL wowlan_config into the shutdown hook. While at it,
check whether the wiphy is also non-NULL before accessing wowlan_config .
Drop the single-use wowlan_config variable, just inline it into function
call.
Fixes: 16bbc3eb8372 ("rsi: fix null pointer dereference during rsi_shutdown()") Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230527222833.273741-1-marex@denx.de Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding a new link to a station, this needs to cause a
recalculation of the minimum chandef since otherwise we can
have a higher bandwidth station connected on that link than
the link is operating at. Do the appropriate recalc.
Building BPF selftests with custom HOSTCFLAGS yields an error:
# make HOSTCFLAGS="-O2"
[...]
HOSTCC ./tools/testing/selftests/bpf/tools/build/resolve_btfids/main.o
main.c:73:10: fatal error: linux/rbtree.h: No such file or directory
73 | #include <linux/rbtree.h>
| ^~~~~~~~~~~~~~~~
The reason is that tools/bpf/resolve_btfids/Makefile passes header
include paths by extending HOSTCFLAGS which is overridden by setting
HOSTCFLAGS in the make command (because of Makefile rules [1]).
This patch fixes the above problem by passing the include paths via
`HOSTCFLAGS_resolve_btfids` which is used by tools/build/Build.include
and can be combined with overridding HOSTCFLAGS.
Currently, on WCN3990, the station disconnect after hardware recovery is
not working as expected. This is because of setting the
IEEE80211_SDATA_DISCONNECT_HW_RESTART flag very early in the hardware
recovery process even before the driver invokes ieee80211_hw_restart().
On the contrary, mac80211 expects this flag to be set after
ieee80211_hw_restart() is invoked for it to trigger station disconnect.
Set the IEEE80211_SDATA_DISCONNECT_HW_RESTART flag in
ath10k_reconfig_complete() instead to fix this.
The other targets are not affected by this change, since the hardware
params flag is not set.
XDP layer will not necessary have access to the 4-bytes FCS checksum.
This leads to bpf_xdp_load_bytes() failing as it tries to copy 64-bytes
from an XDP packet that only have 60-bytes available.
Fixes: 772251742262 ("samples/bpf: fixup some tools to be able to support xdp multibuffer") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Link: https://lore.kernel.org/bpf/168545704139.2996228.2516528552939485216.stgit@firesoul Signed-off-by: Sasha Levin <sashal@kernel.org>
When receiving more rx packets than the kernel can handle the driver
drops the packets and issues an error message. This is bad for two
reasons. The logs are flooded with myriads of messages, but then time
consumed for printing messages in that critical code path brings down
the device. After some time of excessive rx load the driver responds
with:
rtw_8822cu 1-1:1.2: failed to get tx report from firmware
rtw_8822cu 1-1:1.2: firmware failed to report density after scan
rtw_8822cu 1-1:1.2: firmware failed to report density after scan
The device stops working until being replugged.
Fix this by lowering the priority to debug level and also by
ratelimiting it.
Fixes: a82dfd33d1237 ("wifi: rtw88: Add common USB chip support") Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Reviewed-by: Ping-Ke Shih <pkshih@realtek.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230524103934.1019096-1-s.hauer@pengutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
A bad USB device is able to construct a service connection response
message with target endpoint being ENDPOINT0 which is reserved for
HTC_CTRL_RSVD_SVC and should not be modified to be used for any other
services.
Reject such service connection responses.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-by: syzbot+b68fbebe56d8362907e8@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230516150427.79469-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
regulator: Failed to create debugfs directory
...
regulator-dummy: Failed to create debugfs directory
As per the comments for debugfs_create_dir(), errors returned by this
function should be expected, and ignored:
* If debugfs is not enabled in the kernel, the value -%ENODEV will be
* returned.
*
* NOTE: it's expected that most callers should _ignore_ the errors returned
* by this function. Other debugfs functions handle the fact that the "dentry"
* passed to them could be an error and they don't crash in that case.
* Drivers should generally work fine even if debugfs fails to init anyway.
Adhere to the debugfs spirit, and streamline all operations by:
1. Demoting the importance of the printed error messages to debug
level, like is already done in create_regulator(),
2. Further ignoring any returned errors, as by design, all debugfs
functions are no-ops when passed an error pointer.
In case of failure, debugfs_create_dir() does not return NULL, but an
error pointer. Most incorrect error checks were fixed, but the one in
create_regulator() was forgotten.
The sign-file utility (from scripts/) is used in prog_tests/verify_pkcs7_sig.c,
but the utility should not be called as a test. Executing this utility produces
the following error:
selftests: /linux/tools/testing/selftests/bpf: urandom_read
ok 16 selftests: /linux/tools/testing/selftests/bpf: urandom_read
selftests: /linux/tools/testing/selftests/bpf: sign-file
not ok 17 selftests: /linux/tools/testing/selftests/bpf: sign-file # exit=2
Also, urandom_read is mistakenly used as a test. It does not lead to an error,
but should be moved over to TEST_GEN_FILES as well. The empty TEST_CUSTOM_PROGS
can then be removed.
If it fails to attach fentry, the allocated bpf trampoline image will be
left in the system. That can be verified by checking /proc/kallsyms.
This meamleak can be verified by a simple bpf program as follows:
SEC("fentry/trap_init")
int fentry_run()
{
return 0;
}
It will fail to attach trap_init because this function is freed after
kernel init, and then we can find the trampoline image is left in the
system by checking /proc/kallsyms.
After commit e21aa341785c ("bpf: Fix fexit trampoline."), the selector is only
used to indicate how many times the bpf trampoline image are updated and been
displayed in the trampoline ksym name. After the trampoline is freed, the
selector will start from 0 again. So the selector is a useless value to the
user. We can remove it.
If the user want to check whether the bpf trampoline image has been updated
or not, the user can compare the address. Each time the trampoline image is
updated, the address will change consequently. Jiri also pointed out another
issue that perf is still using the old name "bpf_trampoline_%lu", so this
change can fix the issue in perf.
On aarch64, "bpftool feature" reports an incorrect BPF JIT limit:
$ sudo /sbin/bpftool feature
Scanning system configuration...
bpf() syscall restricted to privileged users
JIT compiler is enabled
JIT compiler hardening is disabled
JIT compiler kallsyms exports are enabled for root
skipping kernel config, can't open file: No such file or directory
Global memory limit for JIT compiler for unprivileged users is -201326592 bytes
This is because /proc/sys/net/core/bpf_jit_limit reports
If sock->service_name is NULL, the local variable
service_name_tlv_length will not be assigned by nfc_llcp_build_tlv(),
later leading to using value frmo the stack. Smatch warning:
net/nfc/llcp_commands.c:442 nfc_llcp_send_connect() error: uninitialized symbol 'service_name_tlv_length'.
Fixes: de9e5aeb4f40 ("NFC: llcp: Fix usage of llcp_add_tlv()") Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
n_bytes variable in the driver represents the number of bytes per word
that needs to be sent/copied to fifo. Bits/word can be between 8 and 32
bits from the client but in memory they are a power of 2, same is mentioned
in spi.h header:
"
* @bits_per_word: Data transfers involve one or more words; word sizes
* like eight or 12 bits are common. In-memory wordsizes are
* powers of two bytes (e.g. 20 bit samples use 32 bits).
* This may be changed by the device's driver, or left at the
* default (0) indicating protocol words are eight bit bytes.
* The spi_transfer.bits_per_word can override this for each transfer.
"
Hence, round of n_bytes to a power of 2 to avoid values like 3 which
would generate unalligned/odd accesses to memory/fifo.
* tested on Baikal-T1 based system with DW SPI-looped back interface
transferring a chunk of data with DFS:8,12,16.
Fixes: a51acc2400d4 ("spi: dw: Add support for 32-bits max xfer size") Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com Signed-off-by: Joy Chakraborty <joychakr@google.com Reviewed-by: Serge Semin <fancer.lancer@gmail.com Tested-by: Serge Semin <fancer.lancer@gmail.com Link: https://lore.kernel.org/r/20230512104746.1797865-4-joychakr@google.com Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
With the way the hooks implemented right now, we have a special
condition: optval larger than PAGE_SIZE will expose only first 4k into
BPF; any modifications to the optval are ignored. If the BPF program
doesn't handle this condition by resetting optlen to 0,
the userspace will get EFAULT.
The intention of the EFAULT was to make it apparent to the
developers that the program is doing something wrong.
However, this inadvertently might affect production workloads
with the BPF programs that are not too careful (i.e., returning EFAULT
for perfectly valid setsockopt/getsockopt calls).
Let's try to minimize the chance of BPF program screwing up userspace
by ignoring the output of those BPF programs (instead of returning
EFAULT to the userspace). pr_info_once those cases to
the dmesg to help with figuring out what's going wrong.
Fixes: 0d01da6afc54 ("bpf: implement getsockopt and setsockopt hooks") Suggested-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Stanislav Fomichev <sdf@google.com> Link: https://lore.kernel.org/r/20230511170456.1759459-2-sdf@google.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems like __builtin_offset() doesn't preserve CO-RE field
relocations properly. So if offsetof() macro is defined through
__builtin_offset(), CO-RE-enabled BPF code using container_of() will be
subtly and silently broken.
To avoid this problem, redefine offsetof() and container_of() in the
form that works with CO-RE relocations more reliably.
Fixes: 5fbc220862fc ("tools/libpf: Add offsetof/container_of macro in bpf_helpers.h") Reported-by: Lennart Poettering <lennart@poettering.net> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/r/20230509065502.2306180-1-andrii@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Implement ->bpf_bypass_getsockopt proto callback and filter out
SCTP_SOCKOPT_PEELOFF, SCTP_SOCKOPT_PEELOFF_FLAGS and SCTP_SOCKOPT_CONNECTX3
socket options from running eBPF hook on them.
SCTP_SOCKOPT_PEELOFF and SCTP_SOCKOPT_PEELOFF_FLAGS options do fd_install(),
and if BPF_CGROUP_RUN_PROG_GETSOCKOPT hook returns an error after success of
the original handler sctp_getsockopt(...), userspace will receive an error
from getsockopt syscall and will be not aware that fd was successfully
installed into a fdtable.
As pointed by Marcelo Ricardo Leitner it seems reasonable to skip
bpf getsockopt hook for SCTP_SOCKOPT_CONNECTX3 sockopt too.
Because internaly, it triggers connect() and if error is masked
then userspace will be confused.
This patch was born as a result of discussion around a new SCM_PIDFD interface:
https://lore.kernel.org/all/20230413133355.350571-3-aleksandr.mikhalitsyn@canonical.com/
Fixes: 0d01da6afc54 ("bpf: implement getsockopt and setsockopt hooks") Cc: Daniel Borkmann <daniel@iogearbox.net> Cc: Christian Brauner <brauner@kernel.org> Cc: Stanislav Fomichev <sdf@google.com> Cc: Neil Horman <nhorman@tuxdriver.com> Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Cc: Xin Long <lucien.xin@gmail.com> Cc: linux-sctp@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: netdev@vger.kernel.org Suggested-by: Stanislav Fomichev <sdf@google.com> Acked-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com> Acked-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Mandatory WFA testcase
CT_Security_WPA2Personal_STA_RSNEBoundsVerification-AbsentRSNCap,
performs bounds verfication on Beacon and/or Probe response frames. It
failed and observed the reason to be absence of cipher suite and AKM
suite in RSN information. To fix this, enable the RSN flag before extracting RSN
capabilities.
Fixes: cd21d99e595e ("wifi: wilc1000: validate pairwise and authentication suite offsets") Signed-off-by: Amisha Patel <amisha.patel@microchip.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230421181005.4865-1-amisha.patel@microchip.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The CS_TOGGLE bit when set is supposed to instruct FW to
toggle CS line between words. The driver with intent of
disabling this behaviour has been unsetting BIT(0). This has
not caused any trouble so far because the original BIT(1)
is untouched and BIT(0) likely wasn't being used.
Correct this to prevent a potential future bug.
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org Fixes: 561de45f72bd ("spi: spi-geni-qcom: Add SPI driver support for GENI based QUP") Reviewed-by: Douglas Anderson <dianders@chromium.org Link: https://lore.kernel.org/r/1682412128-1913-1-git-send-email-quic_vnivarth@quicinc.com Signed-off-by: Mark Brown <broonie@kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
The btf_dump/struct_data selftest is failing with:
[...]
test_btf_dump_struct_data:FAIL:unexpected return value dumping fs_context unexpected unexpected return value dumping fs_context: actual -7 != expected 264
[...]
The reason is in btf_dump_type_data_check_overflow(). It does not use
BTF_MEMBER_BITFIELD_SIZE from the struct's member (btf_member). Instead,
it is using the enum size which is 4. It had been working till the recent
commit 4e04143c869c ("fs_context: drop the unused lsm_flags member")
removed an integer member which also removed the 4 bytes padding at the
end of the fs_context. Missing this 4 bytes padding exposed this bug. In
particular, when btf_dump_type_data_check_overflow() reaches the member
'phase', -E2BIG is returned.
The fix is to pass bit_sz to btf_dump_type_data_check_overflow(). In
btf_dump_type_data_check_overflow(), it does a different size check when
bit_sz is not zero.
Fixes: 920d16af9b42 ("libbpf: BTF dumper support for typed data") Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20230428013638.1581263-1-martin.lau@linux.dev Signed-off-by: Sasha Levin <sashal@kernel.org>
For the reasons also described in commit b383e8abed41 ("wifi: ath9k: avoid
uninit memory read in ath9k_htc_rx_msg()"), ath9k_htc_rx_msg() should
validate pkt_len before accessing the SKB.
For example, the obtained SKB may have been badly constructed with
pkt_len = 8. In this case, the SKB can only contain a valid htc_frame_hdr
but after being processed in ath9k_htc_rx_msg() and passed to
ath9k_wmi_ctrl_rx() endpoint RX handler, it is expected to have a WMI
command header which should be located inside its data payload.
Implement sanity checking inside ath9k_wmi_ctrl_rx(). Otherwise, uninit
memory can be referenced.
Tested on Qualcomm Atheros Communications AR9271 802.11n .
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Reported-and-tested-by: syzbot+f2cb6e0ffdb961921e4d@syzkaller.appspotmail.com Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20230424183348.111355-1-pchelkin@ispras.ru Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix ath9k_hw_verify_hang()/ar9003_hw_detect_mac_hang() register offset
calculation (do not overflow the shift for the second register/queues
above five, use the register layout described in the comments above
ath9k_hw_verify_hang() instead).
When function igc_rx_hash() was introduced in v4.20 via commit 0507ef8a0372
("igc: Add transmit and receive fastpath and interrupt handlers"), the
hardware wasn't configured to provide RSS hash, thus it made sense to not
enable net_device NETIF_F_RXHASH feature bit.
The NIC hardware was configured to enable RSS hash info in v5.2 via commit 2121c2712f82 ("igc: Add multiple receive queues control supporting"), but
forgot to set the NETIF_F_RXHASH feature bit.
The original implementation of igc_rx_hash() didn't extract the associated
pkt_hash_type, but statically set PKT_HASH_TYPE_L3. The largest portions of
this patch are about extracting the RSS Type from the hardware and mapping
this to enum pkt_hash_types. This was based on Foxville i225 software user
manual rev-1.3.1 and tested on Intel Ethernet Controller I225-LM (rev 03).
For UDP it's worth noting that RSS (type) hashing have been disabled both for
IPv4 and IPv6 (see IGC_MRQC_RSS_FIELD_IPV4_UDP + IGC_MRQC_RSS_FIELD_IPV6_UDP)
because hardware RSS doesn't handle fragmented pkts well when enabled (can
cause out-of-order). This results in PKT_HASH_TYPE_L3 for UDP packets, and
hash value doesn't include UDP port numbers. Not being PKT_HASH_TYPE_L4, have
the effect that netstack will do a software based hash calc calling into
flow_dissect, but only when code calls skb_get_hash(), which doesn't
necessary happen for local delivery.
For QA verification testing I wrote a small bpftrace prog:
[0] https://github.com/xdp-project/xdp-project/blob/master/areas/hints/monitor_skb_hash_on_dev.bt
Fixes: 2121c2712f82 ("igc: Add multiple receive queues control supporting") Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Yoong Siang <yoong.siang.song@intel.com> Link: https://lore.kernel.org/bpf/168182464270.616355.11391652654430626584.stgit@firesoul Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 8ad075c2eb1f ("sched: Async unthrottling for cfs
bandwidth"), we may update the rq clock multiple times in the loop of
__cfsb_csd_unthrottle().
A prior (although less common) instance of this problem exists in
unthrottle_offline_cfs_rqs().
Cure both by ensuring update_rq_clock() is called before the loop and
setting RQCF_ACT_SKIP during the loop, to supress further updates.
The alternative would be pulling update_rq_clock() out of
unthrottle_cfs_rq(), but that gives an even bigger mess.
Fixes: 8ad075c2eb1f ("sched: Async unthrottling for cfs bandwidth") Reviewed-By: Ben Segall <bsegall@google.com> Suggested-by: Vincent Guittot <vincent.guittot@linaro.org> Signed-off-by: Hao Jia <jiahao.os@bytedance.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Link: https://lkml.kernel.org/r/20230613082012.49615-4-jiahao.os@bytedance.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / thirdparty / kernel / stable.git / log
