Stijn Tintel [Mon, 25 Feb 2019 13:46:10 +0000 (15:46 +0200)]
kernel: add missing config symbols
The addition of kmod-input-touchscreen-ads7846 enabled
INPUT_TOUCHSCREEN, which exposes several other symbols on various
targets. Add those symbols to the generic kernel configs to fix build.
Stijn Tintel [Sun, 24 Feb 2019 22:49:39 +0000 (00:49 +0200)]
kernel: fix kmod-input-touchscreen-ads7846 deps
On targets that don't have input support enabled in the kernel config,
building kmod-input-touchscreen-ads7846 fails due to a missing
dependency on kmod-input-core. Add the dependency to fix this.
max_ttl - limit the ttl in the dns answer if greater as $max_ttl
min_cache_ttl - force caching of dns answers even the ttl in the answer
is lower than the $min_cache_ttl
max_cache_ttl - cache only dns answer for $max_cache_ttl.
Stijn Tintel [Sat, 9 Feb 2019 16:31:48 +0000 (18:31 +0200)]
kernel: add kmod-fb-tft
This module adds support for small TFT LCD display modules. While this
module also exists in the 4.9 kernel, we are not going to support this
kernel in the next major release, so don't make it available for 4.9.
Stijn Tintel [Sat, 9 Feb 2019 16:10:26 +0000 (18:10 +0200)]
kernel: add kmod-fb-sys-ram
The kernel modules that provide support for framebuffers in system RAM
are currently included in the kmod-drm-imx package. Move them to a
separate package, so that other modules can depend on them.
Increase the autoload order of the drm-imx* packages to load the modules
after loading the fb modules they depend on.
Yousong Zhou [Wed, 20 Feb 2019 06:58:51 +0000 (06:58 +0000)]
dnsmasq: prefer localuse over resolvfile guesswork
This makes it clear that localuse when explicitly specified in the
config will have its final say on whether or not the initscript should
touch /etc/resolv.conf, no matter whatever the result of previous
guesswork would be
Oever González [Wed, 20 Feb 2019 16:47:06 +0000 (10:47 -0600)]
ipq-wifi: update ipq-wifi for Linksys EA6350v3
This commit updates the file "board-linksys_ea6359v3".
Without this commit, the Linksys EA6350v3 will experience poor wireless
performance in both bands. With this patch, wireless performace will be
comparable to the performance of the stock firmware.
The board-files are specific to the target and device. Hence
they need to be set as nonshared. Otherwise they do not show
up on the package repository. This causes problems for
imagebuilder, if it needs to build a image for a specific
device that hasn't had the time to have get its boardfile
upstream.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linus Walleij [Fri, 15 Feb 2019 16:02:23 +0000 (17:02 +0100)]
gemini: Generate harddisk image for DNS-313
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.
This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.
We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing] Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.
This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.
before: (Tested on a RT-AC58U, which has SPI-NAND).
# time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064
12064+0 records in
12064+0 records out
real 0m 0.28s
user 0m 0.02s
sys 0m 0.24s
after:
# time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes
1+0 records in
1+0 records out
real 0m 0.01s
user 0m 0.00s
sys 0m 0.00s
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Cherry-pick Multi-AP commits from uptream: 9c06f0f6a hostapd: Add Multi-AP protocol support 5abc7823b wpa_supplicant: Add Multi-AP backhaul STA support a1debd338 tests: Refactor test_multi_ap bfcdac1c8 Multi-AP: Don't reject backhaul STA on fronthaul BSS cb3c156e7 tests: Update multi_ap_fronthaul_on_ap to match implementation 56a2d788f WPS: Add multi_ap_subelem to wps_build_wfa_ext() 83ebf5586 wpa_supplicant: Support Multi-AP backhaul STA onboarding with WPS 66819b07b hostapd: Support Multi-AP backhaul STA onboarding with WPS 8682f384c hostapd: Add README-MULTI-AP b1daf498a tests: Multi-AP WPS provisioning
Add support for Multi-AP to the UCI configuration. Every wifi-iface gets
an option 'multi_ap'. For APs, its value can be 0 (multi-AP support
disabled), 1 (backhaul AP), 2 (fronthaul AP), or 3 (fronthaul + backhaul
AP). For STAs, it can be 0 (not a backhaul STA) or 1 (backhaul STA, can
only associate with backhaul AP).
Also add new optional parameter to wps_start ubus call of
wpa_supplicant to indicate that a Multi-AP backhaul link is required.
Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Daniel Golle [Tue, 19 Feb 2019 17:30:24 +0000 (18:30 +0100)]
mac80211: rt2x00: replace pending by merged patches
Those have by now been merged into wireless-drivers-next: 17ae2acd1a6f rt2x00: remove unneeded check 5991a2ecd070 rt2x00: remove confusing AGC register 9ad3b5565445 rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band 7aca14885ede rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620 c7ff1bfeaf1c rt2800: comment and simplify AGC init for RT6352
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hans Dedecker [Tue, 19 Feb 2019 14:15:54 +0000 (15:15 +0100)]
Revert "iproute2: use tc package variant to limit other package sizes"
This reverts commit e6d84fa8864e7bbbcec139dd09a2922a06f5b2a0 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Hans Dedecker [Tue, 19 Feb 2019 14:14:42 +0000 (15:14 +0100)]
Revert "iproute2: simplify linking libelf for eBFP/XDP object file support"
This reverts commit 26681fa6a6fcbec0024906eb8367e9a3160521fb as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Hans Dedecker [Tue, 19 Feb 2019 14:12:53 +0000 (15:12 +0100)]
Revert "iproute2: tc: enable and fix support for using .so plugins"
This reverts commit fc80ef3613465e60257a5ddf0674debe45b09180 as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and
rdma for the ip-full variant
Hans Dedecker [Tue, 19 Feb 2019 14:10:45 +0000 (15:10 +0100)]
Revert "iproute2: tc: reduce size of dynamic symbol table"
This reverts commit 248797834bf21916ddf663edc96d86ee5377850e as it breaks the
installation of the iproute2 utilities ip-bridge, ss, nstat, devlink and rdma
for the ip-full variant
Yousong Zhou [Sat, 16 Feb 2019 10:36:55 +0000 (10:36 +0000)]
armvirt: 32: enable CONFIG_ARM_LPAE
This is required for running armvirt_32 on QEMU 3.0 [1], otherwise the
kernel will emit the following complaint and virtio-net-pci devices will
fail to be initialized
[ 1.124214] OF: PCI: host bridge /pcie@10000000 ranges:
[ 1.125093] OF: PCI: IO 0x3eff0000..0x3effffff -> 0x00000000
[ 1.125942] OF: PCI: MEM 0x10000000..0x3efeffff -> 0x10000000
[ 1.126403] OF: PCI: MEM 0x8000000000..0xffffffffff -> 0x8000000000
[ 1.127748] pci-host-generic 4010000000.pcie: can't claim ECAM area [mem 0x10000000-0x1fffffff]: address conflict with /pcie@10000000 [mem 0x10000000-0x3efeffff]
[ 1.129752] pci-host-generic: probe of 4010000000.pcie failed with error -16
Running QEMU with "-M virt,highmem=off" is an option, but "highmem" was only
introduced as a default on flag since QEMU 2.5.0 and QEMU will fail and quit on
encounter of unknown flags
[1] Armv7 guest fails to boot with qemu-3.0.0-1,
https://bugzilla.redhat.com/show_bug.cgi?id=1633328#c5
Yousong Zhou [Sat, 16 Feb 2019 10:36:07 +0000 (10:36 +0000)]
armvirt: 32: refresh kernel config
The diff was genereated by running the following command without
actually changing any kernel config options
make kernel_menuconfig CONFIG_TARGET=subtarget
Here are some initial findings on the change
- CONFIG_ARCH_OPTIONAL_KERNEL_RWX is now arch default
- CONFIG_ARM_GIC_V3_ITS is selected by CONFIG_ARCH_VIRT
- CONFIG_CPU_SPECTRE is select by CONFIG_CPU_V7
- CONFIG_TIMER_OF is now a arch default
- CONFIG_TIMER_PROBE is select by CONFIG_TIMER_OF
The following options should probably be moved to generic config
- CONFIG_MIGRATION is a default on option
- CONFIG_TREE_SRCU is a default on option for !PREEMPT && SMP system
- CONFIG_RCU_NEED_SEGCBLIST
Yousong Zhou [Mon, 18 Feb 2019 14:11:19 +0000 (14:11 +0000)]
dnsmasq: allow using dnsmasq as the sole resolver
Currently it seems impossible to configure /etc/config/dhcp to achieve
the following use case
- run dnsmasq with no-resolv
- re-generate /etc/resolv.conf with "nameserver 127.0.0.1"
Before this change, we have to set resolvfile to /tmp/resolv.conf.auto
to achive the 2nd effect above, but setting resolvfile requires noresolv
being false.
A new boolean option "localuse" is added to indicate that we intend to
use dnsmasq as the local dns resolver. It's false by default and to
align with old behaviour it will be true automatically if resolvfile is
set to /tmp/resolv.conf.auto
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com> Acked-by: Hans Dedecker <dedeckeh@gmail.com>
Daniel Golle [Wed, 13 Feb 2019 18:47:18 +0000 (19:47 +0100)]
mac80211: rt2x00: backport accepted and pending patches from upstream
backport from wireless-drivers-next, replacing some existing patches in
our tree (marked with '=' are those which were already present): f483039cf51a rt2x00: use simple_read_from_buffer()
=5c656c71b1bf rt2800: move usb specific txdone/txstatus routines to rt2800lib
=0b0d556e0ebb rt2800mmio: use txdone/txstatus routines from lib
=5022efb50f62 rt2x00: do not check for txstatus timeout every time on tasklet
=adf26a356f13 rt2x00: use different txstatus timeouts when flushing
=0240564430c0 rt2800: flush and txstatus rework for rt2800mmio 6eba8fd22352 rt2x00: rt2400pci: mark expected switch fall-through 10bb92217747 rt2x00: rt2500pci: mark expected switch fall-through 916e6bbcfcff rt2x00: rt2800lib: mark expected switch fall-throughs 641dd8068ecb rt2x00: rt61pci: mark expected switch fall-through 750afb08ca71 cross-tree: phase out dma_zalloc_coherent()
=c2e28ef7711f rt2x00: reduce tx power to nominal level on RT6352 a4296994eb80 rt2x00: Work around a firmware bug with shared keys 2587791d5758 rt2x00: no need to check return value of debugfs_create functions
pending on linux-wireless:
rt2x00: remove unneeded check
rt2x00: remove confusing AGC register
rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band
rt2800: enable TX_PIN_CFG_RFRX_EN only for MT7620
rt2800: comment and simplify AGC init for RT6352
rt2x00: do not print error when queue is full
rt2800: partially restore old mmio txstatus behaviour
rt2800: new flush implementation for SoC devices
rt2800: move txstatus pending routine
rt2800mmio: fetch tx status changes
rt2800mmio: use timer and work for handling tx statuses timeouts
rt2x00: remove last_nostatus_check
rt2x00: remove not used entry field
rt2x00mmio: remove legacy comment
While at it also rename some existing patches now that there are
separate folders with patches for each driver to make things a bit
nicer to handle.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The above commit added to kernel 4.10 added new dependency
for building the NETFILTER_XT_MATCH_SOCKET (xt_socket.ko)
module. The NF_SOCKET_IPVx options (both of them) need to
be enabled in order to build the NETFILTER_XT_MATCH_SOCKET
module. Without the change the module is not built.
Hauke Mehrtens [Sat, 16 Feb 2019 22:43:50 +0000 (23:43 +0100)]
strace: Only allow libdw or libunwind
These two dependencies are mutual exclusive and it is only possible to
select one of them, change the select to a chose so it is only possible
to select one of them in OpenWrt menu config.
Sven Eckelmann [Mon, 11 Feb 2019 15:26:42 +0000 (16:26 +0100)]
build: Accept BIN_DIR parameter for legacy-images
BIN_DIR can be set to overwrite the output path for new images. This is an
advertised feature for the imagebuilder and is used by systems like
LibreMesh's chef.
The legacy images are build using a new sub-make which doesn't receive the
variable overwrites of the parent make process. As result, the BIN_DIR is
automatically defined to the default value from rules.mk. The images will
therefore not be placed in the output path which was selected by the user.
Providing BIN_DIR as an explicit variable override to the sub-make works
around this problem.
Fixes: 26c771452cd8 ("image.mk: add LegacyDevice wrapper to allow legacy image building code to be used for device profiles") Reported-by: Paul Spooren <mail@aparcar.org> Signed-off-by: Sven Eckelmann <sven@narfation.org>
Yangbo Lu [Fri, 15 Feb 2019 03:03:14 +0000 (11:03 +0800)]
kernel: disable CONFIG_USB_IMX21_HCD in default for kernel 4.14
CONFIG_USB_IMX21_HCD should be handled in generic config and
module package. So moved it into generic config.
This also fixed build issue (kernel config question) of layerscape
armv8_32b since it also used ARCH_MXC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[Deactivate CONFIG_USB_IMX21_HCD also for kernel 4.19] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Oskari Lemmela [Sun, 27 Jan 2019 18:20:18 +0000 (20:20 +0200)]
sunxi: fix: A64 unstable timer
Backport A64 unstable timer patches from linux 5.1
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
[Split the single patch into the two original patches] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Applies a patch from https://github.com/openssl/openssl/pull/8213
that fixes an error where open /dev/crypto sessions were not closed.
Thanks to Ansuel Smith for reporting it.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
It was previously added in 546fced, which was part of "intel-microcode:
load as early as possible" series.
Unfortunately the conditionals added to GRUB config caused error on boot,
because on sysupgrade, bootloader is not updated and is left with old
features/modules. Since this module is needed for early microcode load
and transition to this needs to be done step by step, enable the test
module now, so that every newly created image has it already embedded.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
VBoxManage is not used and the image is created with proper permisions: 0f5d0f6 image: use internal qemu-img for vmdk and vdi images drop host
dependencies on qemu-utils and VirtualBox
Unreachable config symbols: 9e0759e x86: merge all geode based subtargets into one
No need to define those symbols since x86_64 is subtarget of x86: 196fb76 x86: make x86_64 a subtarget instead of a standalone target
Unreachable config symbols, so remove GRUB_ROOT: 371b382 x86: remove the xen_domu subtarget
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
config: kernel: Fix missing symbol on brcm2708 with CGROUPS
When CGROUP block io is enabled a new symbol is exposed and needs to
be set or unset else kernel oldconfig hangs waiting for input during
normal OpenWrt builds. Therefore add sane defaults for this symbol
in that case. Also, the defaults brcm2708 are different than generic
defaults because the platform's defconfig enables BLK_DEV_THROTTLING
by default (in defconfig config from the patches used to match
upstream's kernel, not in OpenWrt config-4.xx).
Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com>
[make KERNEL_BLK_DEV_THROTTLING_LOW depend on KERNEL_BLK_DEV_THROTTLING] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
[Remove sha256, nan, bloom, measurements and ftm from tiny version]
[sync nl80211 between backports and iw] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hauke Mehrtens [Fri, 15 Feb 2019 17:43:55 +0000 (18:43 +0100)]
mac80211: update to version 4.19.23-1
This updates mac80211 to backports version 4.19.23-1 which includes all
the stable fixes from kernel 4.19.23.
The removed patches are included in this version.
This causes opkg not offering final release as upgradable version, and
even refusing to update, since it thinks the installed version is
higher.
This can be mitigated by adding ~ between the version and the text, as ~
will order as less than everything except itself. Since 'r' < 't', to
make sure that test will be treated as lower than rc we add a second ~
before the test tag. That way, the ordering becomes
2.80~~test < 2.80~rc < 2.80
which then makes opkg properly treat prerelease versions as lower.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Roman Glova [Tue, 12 Feb 2019 01:59:00 +0000 (20:59 -0500)]
ipq8064: Enabling sata port ipq8064 based devices
(original text here: https://patchwork.kernel.org/patch/8686761/)
On some SOCs PORTS_IMPL register value is never programmed by the BIOS
and left at zero value. Which means that no sata ports are avaiable for
software. AHCI driver used to cope up with this by fabricating the
port_map if the PORTS_IMPL register is read zero, but recent patch
broke this workaround as zero value was valid for nvme disks.
This patch adds ports-implemented dt bindings as workaround for this issue
in a way that DT can dictate the port_map incase where the SOCs does not
program it already.
This patch is equal to commits: 67f8425d0ee1 ("ipq8064: dts: force AP148 SATA port mapping") 2e7a2c91019c ("ARM: dts: qcom: Move common nodes to ipq8064-v.1.0.dtsi")
in the upstream linux kernel.
Signed-off-by: Roman Glova <roman_glova@epam.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[added upstream commits, reorg' commit message]
1. Connect the computer to the LAN port of WN-AC1600DGR
2. Connect power cable to WN-AC1600DGR and turn on it
3. Access to "http://192.168.0.1/" and open firmware update page
("ファームウェア")
4. Select the OpenWrt factory image and click update ("更新") button
5. Wait ~150 seconds to complete flashing
Alternative flash instruction using initramfs image:
1. Prepare a computer and TFTP server software with the IP address
"192.168.99.8" and renamed OpenWrt initramfs image
"uImageWN-AC1600DGR"
2. Connect between WN-AC1600DGR and the computer with UART
3. Connect power cable to WN-AC1600DGR, press "4" on the serial
console and enter the U-Boot console
4. execute "tftpboot" command on the console and download initramfs
image from the TFTP server
5. execute "bootm" command and boot OpenWrt
6. On initramfs image, download the sysupgrade image to the device
and perform sysupgrade with it
7. Wait ~150 seconds to complete flashing
This commit also removes unnecessary "qca,no-eeprom" property from
the ath10k wifi node.
Datasheet states that both PCI ranges are of 0x2000000 size:
0x1000_0000-0x11FF_FFF and 0x1200_0000-0x13FF_0000.
Signed-off-by: Santiago Piccinini <spiccinini@altermundi.net> Reviewed-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed ML notice]
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Linus Walleij [Thu, 7 Feb 2019 19:47:15 +0000 (20:47 +0100)]
gemini: Name binary "bootpart.tar.gz"
This factory binary i supposed to actually be unzipped and
untarred by the user as part of the installation process
(this NAS boots from harddisk), so name it "bootpart.tar.gz"
and not "factory.bin" so it is helpful for users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
INAGAKI Hiroshi [Sun, 3 Feb 2019 02:18:09 +0000 (11:18 +0900)]
ramips: change status LED for Buffalo WHR-G300N
Buffalo WHR-G300N has a LED for power status indication, but it is not
connected to the GPIO and cannot be controlled by the kernel. So,
WHR-G300N uses "ROUTER" LED as the system status LED instead.
This commit changes it to use "DIAG" LED insted of "ROUTER" like
WHR-G301N in ath79 target.
David Bauer [Fri, 1 Feb 2019 23:34:43 +0000 (00:34 +0100)]
ramips: various Netgear R6120 fixes
The R6120 has no 5GHz WLAN LED, the assigned GPIO in fact controls
the WAN LED.
Renames the LED accordingly in the device-tree.
Removes the 5GHz WLAN LED trigger.
Adds the correct WAN port LED trigger.
----
Currently, the MAC address for the Netgear R6120 is read from the NVRAM
partition. The offset for the MAC address however is not consistent
across devices or firmware versions.
Switch to using the factory partition like all other Netgear devices do.
----
The LAN ports of the R6120 are labled in reverse on the casing.
Adjust LuCI switchport numbering accordingly.
----
The WiFi eeprom offsets for the R6120 are currently wrong (5GHz offset
is bigger than the partition itself).
Paul Wassi [Fri, 4 Jan 2019 22:35:09 +0000 (23:35 +0100)]
ath79: change ledtrig on GL.iNet AR150
Change the ledtrig for LAN from netdev to switch.
Although eth1 comes out of the device at a single port,
this port is a switch-port and therefore the LED
must be triggered by that.
projects / thirdparty / openwrt.git / log
