In the error handling for this function, d is freed without ever
removing it from intc_list which would lead to a use after free.
To fix this, let's only add it to the list after everything has
succeeded.
Fixes: 2dcec7a988a1 ("sh: intc: set_irq_wake() support") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This checked if the first character of eisa_device_id::sig was not '\0'.
However, commit ac551828993e changed it as follows:
if (sig[0])
sig[0] is NOT the first character of the eisa_device_id::sig. The
type of 'sig' is 'char (*)[8]', meaning that the type of 'sig[0]' is
'char [8]' instead of 'char'. 'sig[0]' and 'symval' refer to the same
address, which never becomes NULL.
The correct conversion would have been:
if ((*sig)[0])
However, this if-conditional was meaningless because the earlier change
in commit ac551828993e was incorrect.
This commit removes the entire incorrect code, which should never have
been executed.
Fixes: ac551828993e ("modpost: i2c aliases need no trailing wildcard") Fixes: 6543becf26ff ("mod/file2alias: make modalias generation safe for cross compiling") Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Large amount of mount hangs observed during hotplugging of 9pfs devices. The
9pfs Xen driver attempts to initialize itself more than once, causing the
frontend and backend to disagree: the backend listens on a channel that the
frontend does not send on, resulting in stalled processing.
When building the kernel with -Wmaybe-uninitialized, the compiler
reports this warning:
In function 'jffs2_mark_erased_block',
inlined from 'jffs2_erase_pending_blocks' at fs/jffs2/erase.c:116:4:
fs/jffs2/erase.c:474:9: warning: 'bad_offset' may be used uninitialized [-Wmaybe-uninitialized]
474 | jffs2_erase_failed(c, jeb, bad_offset);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
fs/jffs2/erase.c: In function 'jffs2_erase_pending_blocks':
fs/jffs2/erase.c:402:18: note: 'bad_offset' was declared here
402 | uint32_t bad_offset;
| ^~~~~~~~~~
When mtd->point() is used, jffs2_erase_pending_blocks can return -EIO
without initializing bad_offset, which is later used at the filebad
label in jffs2_mark_erased_block.
Fix it by initializing this variable.
Fixes: 8a0f572397ca ("[JFFS2] Return values of jffs2_block_check_erase error paths") Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn> Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 4c39529663b9 ("slab: Warn on duplicate cache names when
DEBUG_VM=y"), the duplicate slab cache names can be detected and a
kernel WARNING is thrown out.
In UBI fast attaching process, alloc_ai() could be invoked twice
with the same slab cache name 'ubi_aeb_slab_cache', which will trigger
following warning messages:
kmem_cache of name 'ubi_aeb_slab_cache' already exists
WARNING: CPU: 0 PID: 7519 at mm/slab_common.c:107
__kmem_cache_create_args+0x100/0x5f0
Modules linked in: ubi(+) nandsim [last unloaded: nandsim]
CPU: 0 UID: 0 PID: 7519 Comm: modprobe Tainted: G 6.12.0-rc2
RIP: 0010:__kmem_cache_create_args+0x100/0x5f0
Call Trace:
__kmem_cache_create_args+0x100/0x5f0
alloc_ai+0x295/0x3f0 [ubi]
ubi_attach+0x3c3/0xcc0 [ubi]
ubi_attach_mtd_dev+0x17cf/0x3fa0 [ubi]
ubi_init+0x3fb/0x800 [ubi]
do_init_module+0x265/0x7d0
__x64_sys_finit_module+0x7a/0xc0
The problem could be easily reproduced by loading UBI device by fastmap
with CONFIG_DEBUG_VM=y.
Fix it by using different slab names for alloc_ai() callers.
Fixes: d2158f69a7d4 ("UBI: Remove alloc_ai() slab name from parameter list") Fixes: fdf10ed710c0 ("ubi: Rework Fastmap attach base code") Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit e874dcde1cbf ("ubifs: Reserve one leb for each journal
head while doing budget"), available space is calulated by deducting
reservation for all journal heads. However, the total block count (
which is only used by statfs) is not updated yet, which will cause
the wrong displaying for used space(total - available).
Fix it by deducting reservation for all journal heads from total
block count.
Fixes: e874dcde1cbf ("ubifs: Reserve one leb for each journal head while doing budget") Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the __rtc_read_time call fails,, the struct rtc_time tm; may contain
uninitialized data, or an illegal date/time read from the RTC hardware.
When calling rtc_tm_to_ktime later, the result may be a very large value
(possibly KTIME_MAX). If there are periodic timers in rtc->timerqueue,
they will continually expire, may causing kernel softlockup.
Fixes: 6610e0893b8b ("RTC: Rework RTC code to use timerqueue for events") Signed-off-by: Yongliang Gao <leonylgao@tencent.com> Acked-by: Jingqun Li <jingqunli@tencent.com> Link: https://lore.kernel.org/r/20241011043153.3788112-1-leonylgao@gmail.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Yang Erkun reports that when two threads are opening files at the same
time, and are forced to abort before a reply is seen, then the call to
nfs_release_seqid() in nfs4_opendata_free() can result in a
use-after-free of the pointer to the defunct rpc task of the other
thread.
The fix is to ensure that if the RPC call is aborted before the call to
nfs_wait_on_sequence() is complete, then we must call nfs_release_seqid()
in nfs4_open_release() before the rpc_task is freed.
Reported-by: Yang Erkun <yangerkun@huawei.com> Fixes: 24ac23ab88df ("NFSv4: Convert open() into an asynchronous RPC call") Reviewed-by: Yang Erkun <yangerkun@huawei.com> Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As support for splitting transmission over several messages using
TX_DATA_CONT was introduced it does not immediately return the return
value of qcom_glink_tx().
The result is that in the intentless case (i.e. intent == NULL), the
code will continue to send all additional chunks. This is wasteful, and
it's possible that the send operation could incorrectly indicate
success, if the last chunk fits in the TX fifo.
If the tag length is >= U32_MAX - 3 then the "length + 4" addition
can result in an integer overflow. Address this by splitting the
decoding into several steps so that decode_cb_compound4res() does
not have to perform arithmetic on the unsafe length value.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Cc: stable@vger.kernel.org Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The output of ".%03u" with the unsigned int in range [0, 4294966295] may
get truncated if the target buffer is not 12 bytes. This can't really
happen here as the 'remainder' variable cannot exceed 999 but the
compiler doesn't know it. To make it happy just increase the buffer to
where the warning goes away.
Fixes: 3c9f3681d0b4 ("[SCSI] lib: add generic helper to print sizes rounded to the correct SI range") Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Reviewed-by: Andy Shevchenko <andy@kernel.org> Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com> Cc: Kees Cook <kees@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Link: https://lore.kernel.org/r/20241101205453.9353-1-brgl@bgdev.pl Signed-off-by: Kees Cook <kees@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check whether the TRB ring is full or empty in dwc3_calc_trbs_left()
is insufficient. It assumes there are active TRBs if there's any request
in the started_list. However, that's not the case for requests with a
large SG list.
That is, if we have a single usb request that requires more TRBs than
the total TRBs in the TRB ring, the queued TRBs will be available when
all the TRBs in the ring are completed. But the request is only
partially completed and remains in the started_list. With the current
logic, the TRB ring is empty, but dwc3_calc_trbs_left() returns 0.
Fix this by additionally checking for the request->num_trbs for active
TRB count.
Atomicity violation occurs when the fmc_send_cmd() function is executed
simultaneously with the modification of the fmdev->resp_skb value.
Consider a scenario where, after passing the validity check within the
function, a non-null fmdev->resp_skb variable is assigned a null value.
This results in an invalid fmdev->resp_skb variable passing the validity
check. As seen in the later part of the function, skb = fmdev->resp_skb;
when the invalid fmdev->resp_skb passes the check, a null pointer
dereference error may occur at line 478, evt_hdr = (void *)skb->data;
To address this issue, it is recommended to include the validity check of
fmdev->resp_skb within the locked section of the function. This
modification ensures that the value of fmdev->resp_skb does not change
during the validation process, thereby maintaining its validity.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations.
Fixes: e8454ff7b9a4 ("[media] drivers:media:radio: wl128x: FM Driver Common sources") Cc: stable@vger.kernel.org Signed-off-by: Qiu-ji Chen <chenqiuji666@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tilt data contained in the Bluetooth packets of an Intuos Pro are
supposed to be interpreted as signed values. Simply casting the values
to type `char` is not guaranteed to work since it is implementation-
defined whether it is signed or unsigned. At least one user has noticed
the data being reported incorrectly on their system. To ensure that the
data is interpreted properly, we specifically cast to `signed char`
instead.
Link: https://github.com/linuxwacom/input-wacom/issues/445 Fixes: 4922cd26f03c ("HID: wacom: Support 2nd-gen Intuos Pro's Bluetooth classic interface") CC: stable@vger.kernel.org # 4.11+ Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Supposing first scenario with a virtio_blk driver.
CPU0 CPU1
blk_mq_try_issue_directly()
__blk_mq_issue_directly()
q->mq_ops->queue_rq()
virtio_queue_rq()
blk_mq_stop_hw_queue()
virtblk_done()
blk_mq_request_bypass_insert() 1) store
blk_mq_start_stopped_hw_queue()
clear_bit(BLK_MQ_S_STOPPED) 3) store
blk_mq_run_hw_queue()
if (!blk_mq_hctx_has_pending()) 4) load
return
blk_mq_sched_dispatch_requests()
blk_mq_run_hw_queue()
if (!blk_mq_hctx_has_pending())
return
blk_mq_sched_dispatch_requests()
if (blk_mq_hctx_stopped()) 2) load
return
__blk_mq_sched_dispatch_requests()
Supposing another scenario.
CPU0 CPU1
blk_mq_requeue_work()
blk_mq_insert_request() 1) store
virtblk_done()
blk_mq_start_stopped_hw_queue()
blk_mq_run_hw_queues() clear_bit(BLK_MQ_S_STOPPED) 3) store
blk_mq_run_hw_queue()
if (!blk_mq_hctx_has_pending()) 4) load
return
blk_mq_sched_dispatch_requests()
if (blk_mq_hctx_stopped()) 2) load
continue
blk_mq_run_hw_queue()
Both scenarios are similar, the full memory barrier should be inserted
between 1) and 2), as well as between 3) and 4) to make sure that either
CPU0 sees BLK_MQ_S_STOPPED is cleared or CPU1 sees dispatch list.
Otherwise, either CPU will not rerun the hardware queue causing
starvation of the request.
The easy way to fix it is to add the essential full memory barrier into
helper of blk_mq_hctx_stopped(). In order to not affect the fast path
(hardware queue is not stopped most of the time), we only insert the
barrier into the slow path. Actually, only slow path needs to care about
missing of dispatching the request to the low-level device driver.
Fixes: 320ae51feed5 ("blk-mq: new multi-queue block IO queueing mechanism") Cc: stable@vger.kernel.org Cc: Muchun Song <muchun.song@linux.dev> Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Link: https://lore.kernel.org/r/20241014092934.53630-4-songmuchun@bytedance.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 18011eac28c7 ("arm64: tls: Avoid unconditional zeroing of
tpidrro_el0 for native tasks") tried to optimise the context switching
of tpidrro_el0 by eliding the clearing of the register when switching
to a native task with kpti enabled, on the erroneous assumption that
the kpti trampoline entry code would already have taken care of the
write.
Although the kpti trampoline does zero the register on entry from a
native task, the check in tls_thread_switch() is on the *next* task and
so we can end up leaving a stale, non-zero value in the register if the
previous task was 32-bit.
Drop the broken optimisation and zero tpidrro_el0 unconditionally when
switching to a native 64-bit task.
Cc: Mark Rutland <mark.rutland@arm.com> Cc: stable@vger.kernel.org Fixes: 18011eac28c7 ("arm64: tls: Avoid unconditional zeroing of tpidrro_el0 for native tasks") Signed-off-by: Will Deacon <will@kernel.org> Acked-by: Mark Rutland <mark.rutland@arm.com> Link: https://lore.kernel.org/r/20241114095332.23391-1-will@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS are selected,
cpu_max_bits_warn() generates a runtime warning similar as below when
showing /proc/cpuinfo. Fix this by using nr_cpu_ids (the runtime limit)
instead of NR_CPUS to iterate CPUs.
Cc: stable@vger.kernel.org Signed-off-by: Huacai Chen <chenhuacai@loongson.cn> Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drvdata is not available in release. Let's just use container_of()
to get the vector_device instance. Otherwise, removing a vector device
will result in a crash:
Currently in omap_8250_shutdown, the dma->rx_running flag is
set to zero in omap_8250_rx_dma_flush. Next pm_runtime_get_sync
is called, which is a runtime resume call stack which can
re-set the flag. When the call omap_8250_shutdown returns, the
flag is expected to be UN-SET, but this is not the case. This
is causing issues the next time UART is re-opened and
omap_8250_rx_dma is called. Fix by moving pm_runtime_get_sync
before the omap_8250_rx_dma_flush.
cc: stable@vger.kernel.org Fixes: 0e31c8d173ab ("tty: serial: 8250_omap: add custom DMA-RX callback") Signed-off-by: Bin Liu <b-liu@ti.com>
[Judith: Add commit message] Signed-off-by: Judith Mendez <jm@ti.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Tested-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20241031172315.453750-1-jm@ti.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drvdata is not available in release. Let's just use container_of()
to get the uml_net instance. Otherwise, removing a network device will
result in a crash:
The drvdata is not available in release. Let's just use container_of()
to get the ubd instance. Otherwise, removing a ubd device will result
in a crash:
During wear-leveing work, the source PEB will be moved into scrub list
when source LEB cannot be locked in ubi_eba_copy_leb(), which is wrong
for non-scrub type source PEB. The problem could bring extra and
ineffective wear-leveing jobs, which makes more or less negative effects
for the life time of flash. Specifically, the process is divided 2 steps:
1. wear_leveling_worker // generate false scrub type PEB
ubi_eba_copy_leb // MOVE_RETRY is returned
leb_write_trylock // trylock failed
scrubbing = 1;
e1 is put into ubi->scrub
2. wear_leveling_worker // schedule false scrub type PEB for wl
scrubbing = 1
e1 = rb_entry(rb_first(&ubi->scrub))
The problem can be reproduced easily by running fsstress on a small
UBIFS partition(<64M, simulated by nandsim) for 5~10mins
(CONFIG_MTD_UBI_FASTMAP=y,CONFIG_MTD_UBI_WL_THRESHOLD=50). Following
message is shown:
ubi0: scrubbed PEB 66 (LEB 0:10), data moved to PEB 165
Since scrub type source PEB has set variable scrubbing as '1', and
variable scrubbing is checked before variable keep, so the problem can
be fixed by setting keep variable as 1 directly if the source LEB cannot
be locked.
Fixes: e801e128b220 ("UBI: fix missing scrub when there is a bit-flip") CC: stable@vger.kernel.org Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When probing spi device take care of deferred probe of ACPI irq gpio
similar like for OF/DT case.
>From practical standpoint this fixes issue with vsc-tp driver on
Dell XP 9340 laptop, which try to request interrupt with spi->irq
equal to -EPROBE_DEFER and fail to probe with the following error:
vsc-tp spi-INTC10D0:00: probe with driver vsc-tp failed with error -22
Suggested-by: Hans de Goede <hdegoede@redhat.com> Fixes: 33ada67da352 ("ACPI / spi: attach GPIO IRQ from ACPI description to SPI device") Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Alexis Lothoré <alexis.lothore@bootlin.com> # Dell XPS9320, ov01a10 Link: https://patch.msgid.link/20241122094224.226773-1-stanislaw.gruszka@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tb[IPSET_ATTR_IP_TO] is not present but tb[IPSET_ATTR_CIDR] exists,
the values of ip and ip_to are slightly swapped. Therefore, the range check
for ip should be done later, but this part is missing and it seems that the
vulnerability occurs.
So we should add missing range checks and remove unnecessary range checks.
Cc: <stable@vger.kernel.org> Reported-by: syzbot+58c872f7790a4d2ac951@syzkaller.appspotmail.com Fixes: 72205fc68bd1 ("netfilter: ipset: bitmap:ip set type support") Signed-off-by: Jeongjun Park <aha310510@gmail.com> Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().
It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:
sci_ports[0] = port A
sci_ports[X] = port B
In this case, the new port mapped at index zero will have associated data
that was used for earlycon.
In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).
To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.
Fix installation of WinUSB driver using OS descriptors. Without the
fix the drivers are not installed correctly and the property
'DeviceInterfaceGUID' is missing on host side.
The original change was based on the assumption that the interface
number is in the high byte of wValue but it is in the low byte,
instead. Unfortunately, the fix is based on MS documentation which is
also wrong.
The actual USB request for OS descriptors (using USB analyzer) looks
like:
C1: bmRequestType (device to host, vendor, interface)
A1: nas magic number
0002: wValue (2: nas interface)
0005: wIndex (5: get extended property i.e. nas interface GUID)
008E: wLength (142)
The fix was tested on Windows 10 and Windows 11.
Cc: stable@vger.kernel.org Fixes: ec6ce7075ef8 ("usb: gadget: composite: fix OS descriptors w_value logic") Signed-off-by: Michal Vrastil <michal.vrastil@hidglobal.com> Signed-off-by: Elson Roy Serrao <quic_eserrao@quicinc.com> Acked-by: Peter korsgaard <peter@korsgaard.com> Link: https://lore.kernel.org/r/20241113235433.20244-1-quic_eserrao@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9bf4e919ccad worked around an issue introduced after an innocuous
optimisation change in LLVM main:
> len is defined as an 'int' because it is assigned from
> '__user int *optlen'. However, it is clamped against the result of
> sizeof(), which has a type of 'size_t' ('unsigned long' for 64-bit
> platforms). This is done with min_t() because min() requires compatible
> types, which results in both len and the result of sizeof() being casted
> to 'unsigned int', meaning len changes signs and the result of sizeof()
> is truncated. From there, len is passed to copy_to_user(), which has a
> third parameter type of 'unsigned long', so it is widened and changes
> signs again. This excessive casting in combination with the KCSAN
> instrumentation causes LLVM to fail to eliminate the __bad_copy_from()
> call, failing the build.
The same issue occurs in rfcomm in functions rfcomm_sock_getsockopt and
rfcomm_sock_getsockopt_old.
Change the type of len to size_t in both rfcomm_sock_getsockopt and
rfcomm_sock_getsockopt_old and replace min_t() with min().
Cc: stable@vger.kernel.org Co-authored-by: Aleksei Vetrov <vvvvvv@google.com>
Improves: 9bf4e919ccad ("Bluetooth: Fix type of len in {l2cap,sco}_sock_getsockopt_old()") Link: https://github.com/ClangBuiltLinux/linux/issues/2007 Link: https://github.com/llvm/llvm-project/issues/85647 Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk> Reviewed-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of
ldiscs") introduces the tty_ldisc_autoload sysctl with the wrong
proc_handler. .extra1 and .extra2 parameters are set to avoid other values
thant SYSCTL_ZERO or SYSCTL_ONE to be set but proc_dointvec do not uses
them.
This commit fixes this by using proc_dointvec_minmax instead of
proc_dointvec.
Fixes: 7c0cca7c847e ("tty: ldisc: add sysctl to prevent autoloading of ldiscs") Cc: stable <stable@kernel.org> Signed-off-by: Nicolas Bouchinet <nicolas.bouchinet@ssi.gouv.fr> Reviewed-by: Lin Feng <linf@wangsu.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Link: https://lore.kernel.org/r/20241112131357.49582-4-nicolas.bouchinet@clip-os.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dennis reports a boot crash on recent Lenovo laptops with a USB4 dock.
Since commit 0fc70886569c ("thunderbolt: Reset USB4 v2 host router") and
commit 59a54c5f3dbd ("thunderbolt: Reset topology created by the boot
firmware"), USB4 v2 and v1 Host Routers are reset on probe of the
thunderbolt driver.
The reset clears the Presence Detect State and Data Link Layer Link Active
bits at the USB4 Host Router's Root Port and thus causes hot removal of the
dock.
The crash occurs when pciehp is unbound from one of the dock's Downstream
Ports: pciehp creates a pci_slot on bind and destroys it on unbind. The
pci_slot contains a pointer to the pci_bus below the Downstream Port, but
a reference on that pci_bus is never acquired. The pci_bus is destroyed
before the pci_slot, so a use-after-free ensues when pci_slot_release()
accesses slot->bus.
In principle this should not happen because pci_stop_bus_device() unbinds
pciehp (and therefore destroys the pci_slot) before the pci_bus is
destroyed by pci_remove_bus_device().
However the stacktrace provided by Dennis shows that pciehp is unbound from
pci_remove_bus_device() instead of pci_stop_bus_device(). To understand
the significance of this, one needs to know that the PCI core uses a two
step process to remove a portion of the hierarchy: It first unbinds all
drivers in the sub-hierarchy in pci_stop_bus_device() and then actually
removes the devices in pci_remove_bus_device(). There is no precaution to
prevent driver binding in-between pci_stop_bus_device() and
pci_remove_bus_device().
In Dennis' case, it seems removal of the hierarchy by pciehp races with
driver binding by pci_bus_add_devices(). pciehp is bound to the
Downstream Port after pci_stop_bus_device() has run, so it is unbound by
pci_remove_bus_device() instead of pci_stop_bus_device(). Because the
pci_bus has already been destroyed at that point, accesses to it result in
a use-after-free.
One might conclude that driver binding needs to be prevented after
pci_stop_bus_device() has run. However it seems risky that pci_slot points
to pci_bus without holding a reference. Solely relying on correct ordering
of driver unbind versus pci_bus destruction is certainly not defensive
programming.
If pci_slot has a need to access data in pci_bus, it ought to acquire a
reference. Amend pci_create_slot() accordingly. Dennis reports that the
crash is not reproducible with this change.
An atomicity violation occurs when the validity of the variables
da7219->clk_src and da7219->mclk_rate is being assessed. Since the entire
assessment is not protected by a lock, the da7219 variable might still be
in flux during the assessment, rendering this check invalid.
To fix this issue, we recommend adding a lock before the block
if ((da7219->clk_src == clk_id) && (da7219->mclk_rate == freq)) so that
the legitimacy check for da7219->clk_src and da7219->mclk_rate is
protected by the lock, ensuring the validity of the check.
This possible bug is found by an experimental static analysis tool
developed by our team. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations.
Commit 7c55b78818cf ("jfs: xattr: fix buffer overflow for invalid xattr")
also addresses this issue but it only fixes it for positive values, while
ea_size is an integer type and can take negative values, e.g. in case of
a corrupted filesystem. This still breaks validation and would overflow
because of implicit conversion from int to size_t in print_hex_dump().
Fix this issue by clamping the ea_size value instead.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
The original implementation ext4's FS_IOC_GETFSMAP handling only
worked when the range of queried blocks included at least one free
(unallocated) block range. This is because how the metadata blocks
were emitted was as a side effect of ext4_mballoc_query_range()
calling ext4_getfsmap_datadev_helper(), and that function was only
called when a free block range was identified. As a result, this
caused generic/365 to fail.
Fix this by creating a new function ext4_getfsmap_meta_helper() which
gets called so that blocks before the first free block range in a
block group can get properly reported.
find_group_other() and find_group_orlov() read *_lo, *_hi with
ext4_free_inodes_count without additional locking. This can cause
data-race warning, but since the lock is held for most writes and free
inodes value is generally not a problem even if it is incorrect, it is
more appropriate to use READ_ONCE()/WRITE_ONCE() than to add locking.
==================================================================
BUG: KCSAN: data-race in ext4_free_inodes_count / ext4_free_inodes_set
write to 0xffff88810404300e of 2 bytes by task 6254 on cpu 1:
ext4_free_inodes_set+0x1f/0x80 fs/ext4/super.c:405
__ext4_new_inode+0x15ca/0x2200 fs/ext4/ialloc.c:1216
ext4_symlink+0x242/0x5a0 fs/ext4/namei.c:3391
vfs_symlink+0xca/0x1d0 fs/namei.c:4615
do_symlinkat+0xe3/0x340 fs/namei.c:4641
__do_sys_symlinkat fs/namei.c:4657 [inline]
__se_sys_symlinkat fs/namei.c:4654 [inline]
__x64_sys_symlinkat+0x5e/0x70 fs/namei.c:4654
x64_sys_call+0x1dda/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:267
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x54/0x120 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x76/0x7e
read to 0xffff88810404300e of 2 bytes by task 6257 on cpu 0:
ext4_free_inodes_count+0x1c/0x80 fs/ext4/super.c:349
find_group_other fs/ext4/ialloc.c:594 [inline]
__ext4_new_inode+0x6ec/0x2200 fs/ext4/ialloc.c:1017
ext4_symlink+0x242/0x5a0 fs/ext4/namei.c:3391
vfs_symlink+0xca/0x1d0 fs/namei.c:4615
do_symlinkat+0xe3/0x340 fs/namei.c:4641
__do_sys_symlinkat fs/namei.c:4657 [inline]
__se_sys_symlinkat fs/namei.c:4654 [inline]
__x64_sys_symlinkat+0x5e/0x70 fs/namei.c:4654
x64_sys_call+0x1dda/0x2d60 arch/x86/include/generated/asm/syscalls_64.h:267
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x54/0x120 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Cc: stable@vger.kernel.org Signed-off-by: Jeongjun Park <aha310510@gmail.com> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Link: https://patch.msgid.link/20241003125337.47283-1-aha310510@gmail.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Multiple profiles shared 'ent->caps', so some logs missed.
Fixes: 0ed3b28ab8bf ("AppArmor: mediation of non file objects") Signed-off-by: chao liu <liuzgyid@outlook.com> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Syzbot reported two possible deadlocks]
The first possible deadlock is:
WARNING: possible recursive locking detected 6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
--------------------------------------------
syz-executor363/2651 is trying to acquire lock: ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x15d/0x2c0 drivers/usb/misc/chaoskey.c:322
but task is already holding lock: ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_release+0x7f/0x2c0 drivers/usb/misc/chaoskey.c:299
other info that might help us debug this:
Possible unsafe locking scenario:
The second possible deadlock is:
WARNING: possible circular locking dependency detected 6.12.0-rc1-syzkaller-00027-g4a9fe2a8ac53 #0 Not tainted
------------------------------------------------------
kworker/0:2/804 is trying to acquire lock: ffffffff899dadb0 (minor_rwsem){++++}-{3:3}, at: usb_deregister_dev+0x7c/0x1e0 drivers/usb/core/file.c:186
but task is already holding lock: ffffffff89b120e8 (chaoskey_list_lock){+.+.}-{3:3}, at: chaoskey_disconnect+0xa8/0x2a0 drivers/usb/misc/chaoskey.c:235
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
*** DEADLOCK ***
[Analysis]
The first is AA lock, it because wrong logic, it need a unlock.
The second is AB lock, it needs to rearrange the order of lock usage.
Fixes: 422dc0a4d12d ("USB: chaoskey: fail open after removal") Reported-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com Reported-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=685e14d04fe35692d3bc Signed-off-by: Edward Adam Davis <eadavis@qq.com> Tested-by: syzbot+685e14d04fe35692d3bc@syzkaller.appspotmail.com Reported-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com Tested-by: syzbot+5f1ce62e956b7b19610e@syzkaller.appspotmail.com Tested-by: syzbot+1f8ca5ee82576ec01f12@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/tencent_84EB865C89862EC22EE94CB3A7C706C59206@qq.com Cc: Oliver Neukum <oneukum@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
chaoskey_open() takes the lock only to increase the
counter of openings. That means that the mutual exclusion
with chaoskey_disconnect() cannot prevent an increase
of the counter and chaoskey_open() returning a success.
If that race is hit, chaoskey_disconnect() will happily
free all resources associated with the device after
it has dropped the lock, as it has read the counter
as zero.
To prevent this race chaoskey_open() has to check
the presence of the device under the lock.
However, the current per device lock cannot be used,
because it is a part of the data structure to be
freed. Hence an additional global mutex is needed.
The issue is as old as the driver.
iowarrior_read() uses the iowarrior dev structure, but does not use any
lock on the structure. This can cause various bugs including data-races,
so it is more appropriate to use a mutex lock to safely protect the
iowarrior dev structure. When using a mutex lock, you should split the
branch to prevent blocking when the O_NONBLOCK flag is set.
In addition, it is unnecessary to check for NULL on the iowarrior dev
structure obtained by reading file->private_data. Therefore, it is
better to remove the check.
On DWMAC3 and later, there's a RX Watchdog interrupt that's used for
interrupt coalescing. It's known to be buggy on some platforms, and
dwmac-socfpga appears to be one of them. Changing the interrupt
coalescing from ethtool doesn't appear to have any effect here.
Without disabling RIWT (Received Interrupt Watchdog Timer, I
believe...), we observe latencies while receiving traffic that amount to
around ~0.4ms. This was discovered with NTP but can be easily reproduced
with a simple ping. Without this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.657 ms
With this patch :
64 bytes from 192.168.5.2: icmp_seq=1 ttl=64 time=0.254 ms
Validate Wake-on-LAN (WoL) options in `lan78xx_set_wol` before calling
`usb_autopm_get_interface`. This prevents USB autopm refcounting issues
and ensures the adapter can properly enter autosuspend when invalid WoL
options are provided.
The hardware on Broadcom 1G chipsets have a known limitation
where they cannot handle DMA addresses that cross over 4GB.
When such an address is encountered, the hardware sets the
address overflow error bit in the DMA status register and
triggers a reset.
However, BCM57766 hardware is setting the overflow bit and
triggering a reset in some cases when there is no actual
underlying address overflow. The hardware team analyzed the
issue and concluded that it is happening when the status
block update has an address with higher (b16 to b31) bits
as 0xffff following a previous update that had lowest bits
as 0xffff.
To work around this bug in the BCM57766 hardware, set the
coherent dma mask from the current 64b to 31b. This will
ensure that upper bits of the status block DMA address are
always at most 0x7fff, thus avoiding the improper overflow
check described above. This work around is intended for only
status block and ring memories and has no effect on TX and
RX buffers as they do not require coherent memory.
Add calls to `phy_device_free` after `fixed_phy_unregister` to fix a
memory leak that occurs when the device is unplugged. This ensures
proper cleanup of pseudo fixed-link PHYs.
Fixes: 89b36fb5e532 ("lan78xx: Lan7801 Support for Fixed PHY") Cc: Raghuram Chary J <raghuramchary.jallipalli@microchip.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://patch.msgid.link/20241116130558.1352230-2-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The put_device() call in power_supply_put() may call
power_supply_dev_release(). The latter function does not sleep so
power_supply_put() doesn't sleep either. Hence, remove the might_sleep()
call from power_supply_put(). This patch suppresses false positive
complaints about calling a sleeping function from atomic context if
power_supply_put() is called from atomic context.
Cc: Kyle Tso <kyletso@google.com> Cc: Krzysztof Kozlowski <krzk@kernel.org> Fixes: 1a352462b537 ("power_supply: Add power_supply_put for decrementing device reference counter") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20240917193914.47566-1-bvanassche@acm.org Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are cases where a PCIe extended capability should be hidden from
the user. For example, an unknown capability (i.e., capability with ID
greater than PCI_EXT_CAP_ID_MAX) or a capability that is intentionally
chosen to be hidden from the user.
Hiding a capability is done by virtualizing and modifying the 'Next
Capability Offset' field of the previous capability so it points to the
capability after the one that should be hidden.
The special case where the first capability in the list should be hidden
is handled differently because there is no previous capability that can
be modified. In this case, the capability ID and version are zeroed
while leaving the next pointer intact. This hides the capability and
leaves an anchor for the rest of the capability list.
However, today, hiding the first capability in the list is not done
properly if the capability is unknown, as struct
vfio_pci_core_device->pci_config_map is set to the capability ID during
initialization but the capability ID is not properly checked later when
used in vfio_config_do_rw(). This leads to the following warning [1] and
to an out-of-bounds access to ecap_perms array.
Fix it by checking cap_id in vfio_config_do_rw(), and if it is greater
than PCI_EXT_CAP_ID_MAX, use an alternative struct perm_bits for direct
read only access instead of the ecap_perms array.
Note that this is safe since the above is the only case where cap_id can
exceed PCI_EXT_CAP_ID_MAX (except for the special capabilities, which
are already checked before).
@ses is initialized to NULL. If __nfsd4_find_backchannel() finds no
available backchannel session, setup_callback_client() will try to
dereference @ses and segfault.
Fixes: dcbeaa68dbbd ("nfsd4: allow backchannel recovery") Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The name len field of the CMD_OPEN packet is only 16-bits and the upper
16-bits of "param2" are a different "prio" field, which can be nonzero in
certain situations, and CMD_OPEN packets can be unexpectedly dropped
because of this.
Fix this by masking out the upper 16 bits of param2.
The upstream GLINK driver was first introduced to communicate with the
RPM on MSM8996, presumably as an artifact from that era the command
defines was prefixed RPM_CMD, while they actually are GLINK_CMDs.
Let's rename these, to keep things tidy. No functional change.
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> Reviewed-by: Chris Lew <quic_clew@quicinc.com> Signed-off-by: Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230214225933.2025595-1-quic_bjorande@quicinc.com
Stable-dep-of: 06c59d97f63c ("rpmsg: glink: use only lower 16-bits of param2 for CMD_OPEN name length") Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_FEC is set (due to COMPILE_TEST) along with
CONFIG_M54xx, coldfire/device.c has compile errors due to
missing MCFEC_* and MCF_IRQ_FEC_* symbols.
Make the whole FEC blocks dependent on having the HW macros
defined, rather than on CONFIG_FEC itself.
This fix is very similar to commit e6e1e7b19fa1 ("m68k: coldfire/device.c: only build for MCF_EDMA when h/w macros are defined")
Fixes: b7ce7f0d0efc ("m68knommu: merge common ColdFire FEC platform setup code")
To: Greg Ungerer <gerg@linux-m68k.org>
To: Geert Uytterhoeven <geert@linux-m68k.org> Cc: linux-m68k@lists.linux-m68k.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Antonio Quartulli <antonio@mandelbit.com> Signed-off-by: Greg Ungerer <gerg@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a typo in the CONFIG_M5441x preprocessor condition, where the GPIO
register offset was incorrectly set to 8 instead of 0. This prevented
proper GPIO configuration for m5441x targets.
Fixes: bea8bcb12da0 ("m68knommu: Add support for the Coldfire m5441x.") Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@yoseli.org> Signed-off-by: Greg Ungerer <gerg@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When config pci_ops.read() can detect failed PCI transactions, the data
returned to the CPU is PCI_ERROR_RESPONSE (~0 or 0xffffffff).
Obviously a successful PCI config read may *also* return that data if a
config register happens to contain ~0, so it doesn't definitively indicate
an error unless we know the register cannot contain ~0.
Use PCI_POSSIBLE_ERROR() to check the response we get when we read data
from hardware. This unifies PCI error response checking and makes error
checks consistent and easier to find.
# perf --debug verbose=3 probe -x test_cpp_mangle --add "test=print_data(int)"
probe-definition(0): test=print_data(int)
symbol:print_data(int) file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Open Debuginfo file: /home/niayan01/test_cpp_mangle
Try to find probe point from debuginfo.
Symbol print_data(int) address found : afc
Matched function: print_data [2ccf]
Probe point found: print_data+0
Found 1 probe_trace_events.
Opening /sys/kernel/tracing//uprobe_events write=1
Opening /sys/kernel/tracing//README write=0
Writing event: p:probe_test_cpp_mangle/test /home/niayan01/test_cpp_mangle:0xb38
...
When tried to probe symbol "print_data(int)", the log shows:
Symbol print_data(int) address found : afc
The found address is 0xafc - which is right with verifying the output
result from nm. Afterwards when write event, the command uses offset
0xb38 in the last log, which is a wrong address.
The dwarf_diename() gets a common function name, in above case, it
returns string "print_data". As a result, the tool parses the offset
based on the common name. This leads to probe at the wrong symbol
"print_data(Point&)".
To fix the issue, use the die_get_linkage_name() function to retrieve
the distinct linkage name - this is the mangled name for the C++ case.
Based on this unique name, the tool can get a correct offset for
probing. Based on DWARF doc, it is possible the linkage name is missed
in the DIE, it rolls back to use dwarf_diename().
After:
# perf --debug verbose=3 probe -x test_cpp_mangle --add "test=print_data(int)"
probe-definition(0): test=print_data(int)
symbol:print_data(int) file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Open Debuginfo file: /home/niayan01/test_cpp_mangle
Try to find probe point from debuginfo.
Symbol print_data(int) address found : afc
Matched function: print_data [2d06]
Probe point found: print_data+0
Found 1 probe_trace_events.
Opening /sys/kernel/tracing//uprobe_events write=1
Opening /sys/kernel/tracing//README write=0
Writing event: p:probe_test_cpp_mangle/test /home/niayan01/test_cpp_mangle:0xafc
Added new event:
probe_test_cpp_mangle:test (on print_data(int) in /home/niayan01/test_cpp_mangle)
You can now use it in all perf tools, such as:
perf record -e probe_test_cpp_mangle:test -aR sleep 1
# perf --debug verbose=3 probe -x test_cpp_mangle --add "test2=print_data(Point&)"
probe-definition(0): test2=print_data(Point&)
symbol:print_data(Point&) file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Open Debuginfo file: /home/niayan01/test_cpp_mangle
Try to find probe point from debuginfo.
Symbol print_data(Point&) address found : b38
Matched function: print_data [2ccf]
Probe point found: print_data+0
Found 1 probe_trace_events.
Opening /sys/kernel/tracing//uprobe_events write=1
Parsing probe_events: p:probe_test_cpp_mangle/test /home/niayan01/test_cpp_mangle:0x0000000000000afc
Group:probe_test_cpp_mangle Event:test probe:p
Opening /sys/kernel/tracing//README write=0
Writing event: p:probe_test_cpp_mangle/test2 /home/niayan01/test_cpp_mangle:0xb38
Added new event:
probe_test_cpp_mangle:test2 (on print_data(Point&) in /home/niayan01/test_cpp_mangle)
You can now use it in all perf tools, such as:
perf record -e probe_test_cpp_mangle:test2 -aR sleep 1
Fixes: fb1587d869a3 ("perf probe: List probes with line number and file name") Signed-off-by: Leo Yan <leo.yan@arm.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Link: https://lore.kernel.org/r/20241012141432.877894-1-leo.yan@arm.com Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to access the registers of the HW, we need to make sure that
the AXI bus clock is enabled. Hence let's increase the number of clocks
by one.
In order to keep backward compatibility and make sure old DTs still work
we check if clock-names is available or not. If it is, then we can
disambiguate between really having the AXI clock or a parent clock and
so we can enable the bus clock. If not, we fallback to what was done
before and don't explicitly enable the AXI bus clock.
Note that if clock-names is given, the axi clock must be the last one in
the phandle array (also enforced in the DT bindings) so that we can reuse
as much code as possible.
In order to access the registers of the HW, we need to make sure that
the AXI bus clock is enabled. Hence let's increase the number of clocks
by one and add clock-names to differentiate between parent clocks and
the bus clock.
This change converts the old binding for the AXI clkgen driver to a yaml
format.
As maintainers, added:
- Lars-Peter Clausen <lars@metafoo.de> - as original author of driver &
binding
- Michael Hennerich <michael.hennerich@analog.com> - as supporter of
Analog Devices drivers
Acked-by: Michael Hennerich <michael.hennerich@analog.com> Acked-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20201013143421.84188-1-alexandru.ardelean@analog.com Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Stable-dep-of: 47f3f5a82a31 ("dt-bindings: clock: axi-clkgen: include AXI clk") Signed-off-by: Sasha Levin <sashal@kernel.org>
When information such as info->screen_base is not ready, calling
sh7760fb_free_mem() does not release memory correctly. Call
dma_free_coherent() instead.
Pass the hardware device to the DMA helpers dma_alloc_coherent() and
dma_free_coherent(). The fbdev device that is currently being used is
a software device and does not provide DMA memory. Also update the
related dev_*() output statements similarly.
Uninit was created at:
__alloc_pages_noprof+0x9a7/0xe00
alloc_pages_mpol_noprof+0x299/0x990
alloc_pages_noprof+0x1bf/0x1e0
allocate_slab+0x33a/0x1250
___slab_alloc+0x12ef/0x35e0
kmem_cache_alloc_bulk_noprof+0x486/0x1330
__io_alloc_req_refill+0x84/0x560
io_submit_sqes+0x172f/0x2f30
__se_sys_io_uring_enter+0x406/0x41c0
__x64_sys_io_uring_enter+0x11f/0x1a0
x64_sys_call+0x2b54/0x3ba0
do_syscall_64+0xcd/0x1e0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Since an instance of 'struct kiocb' may be passed from the block layer
with 'private' field uninitialized, introduce 'ocfs2_iocb_init_rw_locked()'
and use it from where 'ocfs2_dio_end_io()' might take care, i.e. in
'ocfs2_file_read_iter()' and 'ocfs2_file_write_iter()'.
Link: https://lkml.kernel.org/r/20241029091736.1501946-1-dmantipov@yandex.ru Fixes: 7cdfc3a1c397 ("ocfs2: Remember rw lock level during direct io") Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru> Reported-by: syzbot+a73e253cca4f0230a5a5@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=a73e253cca4f0230a5a5 Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hook "qedi_ops->common->sb_init = qed_sb_init" does not release the DMA
memory sb_virt when it fails. Add dma_free_coherent() to free it. This
is the same way as qedr_alloc_mem_sb() and qede_alloc_mem_sb().
Fixes: ace7f46ba5fd ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.") Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com> Link: https://lore.kernel.org/r/20241026125711.484-3-thunder.leizhen@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value of scsi_device_reprobe() is currently ignored in
_scsih_reprobe_lun(). Fixing the calling code to deal with the potential
error is non-trivial, so for now just WARN_ON().
The handling of scsi_device_reprobe()'s return value refers to
_scsih_reprobe_lun() and the following link:
Fixes: f99be43b3024 ("[SCSI] fusion: power pc and miscellaneous bug fixs") Signed-off-by: Zeng Heng <zengheng4@huawei.com> Link: https://lore.kernel.org/r/20241024084417.154655-1-zengheng4@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Don't call bfad_im_module_exit() if bfad_im_module_init() failed.
Fixes: 7725ccfda597 ("[SCSI] bfa: Brocade BFA FC SCSI driver") Signed-off-by: Ye Bin <yebin10@huawei.com> Link: https://lore.kernel.org/r/20241023011809.63466-1-yebin@huaweicloud.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Invalidate rkey is cpu endian and immediate data is in big endian format.
Both immediate data and invalidate the remote key returned by
HW is in little endian format.
While handling the commit in fixes tag, the difference between
immediate data and invalidate rkey endianness was not considered.
Without changes of this patch, Kernel ULP was failing while processing
inv_rkey.
dmesg log snippet -
nvme nvme0: Bogus remote invalidation for rkey 0x2000019Fix in this patch
Do endianness conversion based on completion queue entry flag.
Also, the HW completions are already converted to host endianness in
bnxt_qplib_cq_process_res_rc and bnxt_qplib_cq_process_res_ud and there
is no need to convert it again in bnxt_re_poll_cq. Modified the union to
hold the correct data type.
The pmecc "user" structure is allocated in atmel_pmecc_create_user() and
was supposed to be freed with atmel_pmecc_destroy_user(), but this other
helper is never called. One solution would be to find the proper
location to call the destructor, but the trend today is to switch to
device managed allocations, which in this case fits pretty well.
Replace kzalloc() by devm_kzalloc() and drop the destructor entirely.
Reported-by: "Dr. David Alan Gilbert" <linux@treblig.org> Closes: https://lore.kernel.org/all/ZvmIvRJCf6VhHvpo@gallifrey/ Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20241001203149.387655-1-miquel.raynal@bootlin.com Signed-off-by: Sasha Levin <sashal@kernel.org>
When cpufreq_register_driver() returns error, the cpufreq_init() returns
without unregister platform_driver, fix by add missing
platform_driver_unregister() when cpufreq_register_driver() failed.
Fixes: f8ede0f700f5 ("MIPS: Loongson 2F: Add CPU frequency scaling support") Signed-off-by: Yuan Can <yuancan@huawei.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Symbol table '.dynsym' contains 12 entries:
Num: Value Size Type Bind Vis Ndx Name
...
1: 0000000000000524 84 NOTYPE GLOBAL DEFAULT 8 __[...]@@LINUX_2.6.15
...
4: 0000000000000000 0 OBJECT GLOBAL DEFAULT ABS LINUX_2.6.15
5: 00000000000006c0 48 NOTYPE GLOBAL DEFAULT 8 __[...]@@LINUX_2.6.15
Symbol table '.symtab' contains 56 entries:
Num: Value Size Type Bind Vis Ndx Name
...
45: 0000000000000000 0 OBJECT GLOBAL DEFAULT ABS LINUX_2.6.15
46: 00000000000006c0 48 NOTYPE GLOBAL DEFAULT 8 __kernel_getcpu
47: 0000000000000524 84 NOTYPE GLOBAL DEFAULT 8 __kernel_clock_getres
To overcome that, commit ba83b3239e65 ("selftests: vDSO: fix vDSO
symbols lookup for powerpc64") was applied to have selftests also
look for NOTYPE symbols, but the correct fix should be to flag VDSO
entry points as functions.
The original commit that brought VDSO support into powerpc/64 has the
following explanation:
Note that the symbols exposed by the vDSO aren't "normal" function symbols, apps
can't be expected to link against them directly, the vDSO's are both seen
as if they were linked at 0 and the symbols just contain offsets to the
various functions. This is done on purpose to avoid a relocation step
(ppc64 functions normally have descriptors with abs addresses in them).
When glibc uses those functions, it's expected to use it's own trampolines
that know how to reach them.
The descriptors it's talking about are the OPD function descriptors
used on ABI v1 (big endian). But it would be more correct for a text
symbol to have type function, even if there's no function descriptor
for it.
glibc has a special case already for handling the VDSO symbols which
creates a fake opd pointing at the kernel symbol. So changing the VDSO
symbol type to function shouldn't affect that.
For ABI v2, there is no function descriptors and VDSO functions can
safely have function type.
So lets flag VDSO entry points as functions and revert the
selftest change.
When a tracepoint event is created with attr.freq = 1,
'hwc->period_left' is not initialized correctly. As a result,
in the perf_swevent_overflow() function, when the first time the event occurs,
it calculates the event overflow and the perf_swevent_set_period() returns 3,
this leads to the event are recorded for three duplicate times.
The ndev->npinfo pointer in netpoll_poll_lock() is RCU-protected but is
being accessed directly for a NULL check. While no RCU read lock is held
in this context, we should still use proper RCU primitives for
consistency and correctness.
Replace the direct NULL check with rcu_access_pointer(), which is the
appropriate primitive when only checking for NULL without dereferencing
the pointer. This function provides the necessary ordering guarantees
without requiring RCU read-side protection.
Fixes: bea3348eef27 ("[NET]: Make NAPI polling independent of struct net_device objects.") Signed-off-by: Breno Leitao <leitao@debian.org> Reviewed-by: Michal Kubiak <michal.kubiak@intel.com> Link: https://patch.msgid.link/20241118-netpoll_rcu-v1-2-a1888dcb4a02@debian.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current 6fire code tries to release the resources right after the
call of usb6fire_chip_abort(). But at this moment, the card object
might be still in use (as we're calling snd_card_free_when_closed()).
For avoid potential UAFs, move the release of resources to the card's
private_free instead of the manual call of usb6fire_chip_destroy() at
the USB disconnect callback.
The USB disconnect callback is supposed to be short and not too-long
waiting. OTOH, the current code uses snd_card_free() at
disconnection, but this waits for the close of all used fds, hence it
can take long. It eventually blocks the upper layer USB ioctls, which
may trigger a soft lockup.
An easy workaround is to replace snd_card_free() with
snd_card_free_when_closed(). This variant returns immediately while
the release of resources is done asynchronously by the card device
release at the last close.
This patch also splits the code to the disconnect and the free phases;
the former is called immediately at the USB disconnect callback while
the latter is called from the card destructor.
The USB disconnect callback is supposed to be short and not too-long
waiting. OTOH, the current code uses snd_card_free() at
disconnection, but this waits for the close of all used fds, hence it
can take long. It eventually blocks the upper layer USB ioctls, which
may trigger a soft lockup.
An easy workaround is to replace snd_card_free() with
snd_card_free_when_closed(). This variant returns immediately while
the release of resources is done asynchronously by the card device
release at the last close.
The loop of us122l->mmap_count check is dropped as well. The check is
useless for the asynchronous operation with *_when_closed().
The perfmon sampling mutates shared GPU state (e.g. VIVS_HI_CLOCK_CONTROL
to select the pipe for the perf counter reads). To avoid clashing with
other functions mutating the same state (e.g. etnaviv_gpu_update_clock)
the perfmon sampling needs to hold the GPU lock.
Fixes: 68dc0b295dcb ("drm/etnaviv: use 'sync points' for performance monitor requests") Reviewed-by: Christian Gmeiner <cgmeiner@igalia.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Older GC300 revisions have their power registers at an offset of 0x200
rather than 0x100. Add new gpu_read_power and gpu_write_power functions
to encapsulate accesses to the power addresses and fix the addresses.
Signed-off-by: Doug Brown <doug@schmorgal.com> Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Stable-dep-of: 37dc4737447a ("drm/etnaviv: hold GPU lock across perfmon sampling") Signed-off-by: Sasha Levin <sashal@kernel.org>
This is the only place in the driver that should have to deal with
the raw hardware fences. To avoid any further confusion, consolidate
the fence handling in this file and remove any traces of this from
the header files.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Stable-dep-of: 37dc4737447a ("drm/etnaviv: hold GPU lock across perfmon sampling") Signed-off-by: Sasha Levin <sashal@kernel.org>
Replace one-element array with a flexible-array member in `struct
mwifiex_ie_types_wildcard_ssid_params` to fix the following warning
on a MT8173 Chromebook (mt8173-elm-hana):
[ 356.775250] ------------[ cut here ]------------
[ 356.784543] memcpy: detected field-spanning write (size 6) of single field "wildcard_ssid_tlv->ssid" at drivers/net/wireless/marvell/mwifiex/scan.c:904 (size 1)
[ 356.813403] WARNING: CPU: 3 PID: 742 at drivers/net/wireless/marvell/mwifiex/scan.c:904 mwifiex_scan_networks+0x4fc/0xf28 [mwifiex]
The "(size 6)" above is exactly the length of the SSID of the network
this device was connected to. The source of the warning looks like:
There is a #define WILDCARD_SSID_TLV_MAX_SIZE that uses sizeof() on this
struct, but it already didn't account for the size of the one-element
array, so it doesn't need to be changed.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Acked-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241007222301.24154-1-alpernebiyasak@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
During the xdp_adjust_tail test, probabilistic failure occurs and SKB package
is discarded by the kernel. After checking the issues by tracking SKB package,
it is identified that they were caused by checksum errors. Refer to checksum
of the arch/arm64/include/asm/checksum.h for fixing.
v2: Based on Alexei Starovoitov's suggestions, it is necessary to keep the code
implementation consistent.
omap_gem_new_dmabuf() creates the new gem object, and then takes and
holds the omap_obj->lock for the rest of the function. This has two
issues:
- omap_gem_free_object(), which is called in the error paths, also takes
the same lock, leading to deadlock
- Even if the above wouldn't happen, in the error cases
omap_gem_new_dmabuf() still unlocks omap_obj->lock, even after the
omap_obj has already been freed.
Furthermore, I don't think there's any reason to take the lock at all,
as the object was just created and not yet shared with anyone else.
To fix all this, drop taking the lock.
Fixes: 3cbd0c587b12 ("drm/omap: gem: Replace struct_mutex usage with omap_obj private lock") Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/all/511b99d7-aade-4f92-bd3e-63163a13d617@stanley.mountain/ Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240806-omapdrm-misc-fixes-v1-3-15d31aea0831@ideasonboard.com Signed-off-by: Sasha Levin <sashal@kernel.org>
UBSAN: array-index-out-of-bounds in drivers/net/wireless/ath/ath9k/htc_hst.c:26:51
index 255 is out of range for type 'htc_endpoint [22]'
CPU: 0 UID: 0 PID: 8 Comm: kworker/0:0 Not tainted 6.11.0-rc6-dirty #14
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Workqueue: events request_firmware_work_func
Call Trace:
<TASK>
dump_stack_lvl+0x180/0x1b0
__ubsan_handle_out_of_bounds+0xd4/0x130
htc_issue_send.constprop.0+0x20c/0x230
? _raw_spin_unlock_irqrestore+0x3c/0x70
ath9k_wmi_cmd+0x41d/0x610
? mark_held_locks+0x9f/0xe0
...
Since this bug has been confirmed to be caused by insufficient verification
of conn_rsp_epid, I think it would be appropriate to add a range check for
conn_rsp_epid to htc_connect_service() to prevent the bug from occurring.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.") Signed-off-by: Jeongjun Park <aha310510@gmail.com> Acked-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://patch.msgid.link/20240909103855.68006-1-aha310510@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The INTERVAL_TREE_DEFINE() uncoditionally provides a bunch of helper
functions which in some cases may be not used. This, in particular,
prevents kernel builds with clang, `make W=1` and CONFIG_WERROR=y:
Fix a kernel crash with the below call trace when the SCPI firmware
returns OPP count of zero.
dvfs_info.opp_count may be zero on some platforms during the reboot
test, and the kernel will crash after dereferencing the pointer to
kcalloc(info->count, sizeof(*opp), GFP_KERNEL).
Fixes: 8cb7cf56c9fe ("firmware: add support for ARM System Control and Power Interface(SCPI) protocol") Signed-off-by: Luo Qiu <luoqiu@kylinsec.com.cn>
Message-Id: <55A2F7A784391686+20241101032115.275977-1-luoqiu@kylinsec.com.cn> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Lockdep gives a false positive splat as it can't distinguish the lock
which is taken by different IRQ descriptors from different IRQ chips
that are organized in a way of a hierarchy:
======================================================
WARNING: possible circular locking dependency detected 6.12.0-rc5-next-20241101-00148-g9fabf8160b53 #562 Tainted: G W
------------------------------------------------------
modprobe/141 is trying to acquire lock: ffff899446947868 (intel_soc_pmic_bxtwc:502:(&bxtwc_regmap_config)->lock){+.+.}-{4:4}, at: regmap_update_bits_base+0x33/0x90
but task is already holding lock: ffff899446947c68 (&d->lock){+.+.}-{4:4}, at: __setup_irq+0x682/0x790
The DCDC5 voltage rail in the X-Powers AXP809 PMIC has a resolution of
50mV, so the currently enforced limits of 1.475 and 1.525 volts cannot
be set, when the existing regulator value is beyond this range.
This will lead to the whole regulator driver to give up and fail
probing, which in turn will hang the system, as essential devices depend
on the PMIC.
In this case a bug in U-Boot set the voltage to 1.75V (meant for DCDC4),
and the AXP driver's attempt to correct this lead to this error:
==================
[ 4.447653] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded
[ 4.450066] vcc-dram: Bringing 1750000uV into 1575000-1575000uV
[ 4.460272] vcc-dram: failed to apply 1575000-1575000uV constraint: -EINVAL
[ 4.474788] axp20x-regulator axp20x-regulator.0: Failed to register dcdc5
[ 4.482276] axp20x-regulator axp20x-regulator.0: probe with driver axp20x-regulator failed with error -22
==================
Set the limits to values that can be programmed, so any correction will
be successful.
GCC 13 complains about the truncated output of snprintf():
drivers/mmc/host/mmc_spi.c: In function ‘mmc_spi_response_get’:
drivers/mmc/host/mmc_spi.c:227:64: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^
drivers/mmc/host/mmc_spi.c:227:9: note: ‘snprintf’ output between 26 and 43 bytes into a destination of size 32
227 | snprintf(tag, sizeof(tag), " ... CMD%d response SPI_%s",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
228 | cmd->opcode, maptype(cmd));
Drop it and fold the string it generates into the only place where it's
emitted - the dev_dbg() call at the end of the function.
This loop is supposed to break if the frequency returned from
clk_round_rate() is the same as on the previous iteration. However,
that check doesn't make sense on the first iteration through the loop.
It leads to reading before the start of these->clk_perf_tbl[] array.
projects / thirdparty / kernel / stable.git / log
