kernel: disable CONFIG_CPU_LITTLE_ENDIAN in generic config
Endianness depends on CPU architecture. CONFIG_CPU_(BIG/LITTLE)_ENDIAN should
be enabled on target or subtarget based on SoC architecture.
Fixes warning:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
...
.config:1008:warning: override: CPU_LITTLE_ENDIAN changes choice state
....
Summary:
- ARC - only the CONFIG_CPU_BIG_ENDIAN symbol is defined for this architeture.
If it is disabled then the processor operates in LITTLE_ENDIAN mode (default),
- ARM32 - CONFIG_CPU_LITTLE_ENDIAN symbol available since kernel 5.19. This
option should be enabled after OpenWRT moves to kernel 6.x. After refreshing
the kernel, the symbol disappears,
- ARM64 - enabled CONFIG_CPU_LITTLE_ENDIAN,
- MIPS - enabled relevant symbols,
- POWERPC - enabled CONFIG_CPU_BIG_ENDIAN,
- UML - Symbols are not defined for this architecture,
- X86 - always little endian. Symbols are not defined for this architecture.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This comit fixes warnings that occur on kernel 5.15:
...
[ 2.269736] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 1e108000.switch-mii:00:
PHY has delays (e.g. via pin strapping), but phy-mode = 'rgmii'
[ 2.269736] Should be 'rgmii-id' to use internal delays txskew:1500 ps rxskew:1500 ps
...
Arınç ÜNAL [Tue, 18 Oct 2022 08:54:20 +0000 (11:54 +0300)]
bcm53xx: enable Broadcom 4366b1 firmware for Asus RT-AC88U
On some of the hardware revisions of Asus RT-AC88U, brcmfmac detects the
4366b1 wireless chip and tries to load the firmware file which doesn't
exist because it's not included in the image.
Therefore, include firmware for 4366b1 along with 4366c0. This way, all
hardware revisions of the router will be supported by having brcmfmac use
the firmware file for the wireless chip it detects.
Daniel Golle [Thu, 20 Oct 2022 19:20:41 +0000 (20:20 +0100)]
mediatek: filogic: consolidate adc '32k' clock
Add dependency to '32k' ADC clock so it is always enabled for thermal
and raw access to ADC values. This allows to remove the patch for the
ADC driver and reduce the patch adding thermal support for MT7986 to
only add the new efuse layout and temperature decoding for V3.
Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Zhang Hua [Sun, 2 Oct 2022 11:04:12 +0000 (19:04 +0800)]
scripts/download.pl: pass aria2 config in ENV only
The aria2c command tries to load config from
${XDG_CONFIG_HOME:-${HOME}/.config}/aria2/aria2.conf by default,
which may result unexpected behavior.
As a replacement, people can use environment variable ARIA2C_OPTIONS
to custom arguments passed to aria2c like curl and wget below.
Including --conf-path=/path/to/config.conf in ARIA2C_OPTIONS can
also set a custom config file path easily if needed.
Mark Mentovai [Sun, 11 Sep 2022 17:48:17 +0000 (13:48 -0400)]
kernel: disable stack validation for external module builds as needed
c3e31b6a9b04 and 5f8e5872406d disable stack validation when the build
host is not running Linux, as the objtool kernel build tool required for
stack validation is not portable to other build host environments. This
was achieved by setting CONFIG_STACK_VALIDATION= in KERNEL_MAKEOPTS, and
by setting SKIP_STACK_VALIDATION=1 in the environment. KERNEL_MAKEOPTS
only has effect for the kernel build, not for external module builds,
but through kernel 5.14, SKIP_STACK_VALIDATION worked to disable this
feature too, so stack validation was disabled for external module builds
as well. Since kernel 0d989ac2c90b, the kernel build no longer considers
SKIP_STACK_VALIDATION, so the feature will be disabled for the kernel
build, but not for external module builds.
When building OpenWrt on a non-Linux build host targeting x86 (the only
target architecture for which OpenWrt enables the kernel
CONFIG_STACK_VALIDATION) and using kernel 5.15 (such as via
CONFIG_TESTING_KERNEL), this caused a build failure during any external
module build, such as kmod-button-hotplug. This manifested as build
errors such as:
make[4]: *** No rule to make target
'.../build_dir/target-x86_64_musl/linux-x86_64/button-hotplug/button-hotplug.o',
needed by
'.../build_dir/target-x86_64_musl/linux-x86_64/button-hotplug/button-hotplug.mod'.
Stop.
Although button-hotplug.c was present, the implicit rule to make
$(obj)/%.o from $(src)/%.c in the kernel's scripts/Makefile.build could
not be satisfied in this case, as it also depends on $(objtool_dep),
non-empty as a result of the failure to propagate disabling of stack
validation to external module builds, in a configuration where it is not
possible to build objtool.
KERNEL_MAKEOPTS is used for just the kernel build itself, while
KERNEL_MAKE_FLAGS is used for both the kernel build and for external
module builds. This restores the ability to build OpenWrt in such
configurations by moving the CONFIG_STACK_VALIDATION= make argument from
KERNEL_MAKEOPTS to KERNEL_MAKE_FLAGS where it is able to affect external
module builds properly.
Note that the kernel's objtool and related configuration have seen a
major overhaul since kernel 5.15, and may need more attention again
after 22922deae13f, in kernel 5.19.
John Audia [Fri, 21 Jan 2022 19:12:53 +0000 (14:12 -0500)]
mt7622: switch default CPU governor to ondemand
The most common CPU governor in the OpenWRT project is currently ondemand (see
below). Switch mt7622 over to it as well.
Audit the code by running the following and then analyzing the results:
find -name 'config-5.*' -print0 | xargs -0 grep 'CONFIG_CPU_FREQ_DEFAULT_GOV.*=y'
scripts/download.pl: make the download tool configurable
Introduce a new option in the "Advanced configuration options" to
configure a custom download tool.
By declaring a string in "Use custom download tool" an user can force
what command to use to download package. With the string empty the
default tool used is curl, with wget as a fallback if not available.
download.pl supports 3 tools officially aria2c, curl and wget.
If one of the tool is used in this config, download.pl will use the
default args to make use of them.
If the provided string is different than aria2c, curl or wget, the command
is used as is and the download url will be appended at the end of such command.
While at it also tweak the tool selection logic and chose the tool only
once when the script is called and move aria2c specific variables in the
relevant section.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Wed, 19 Oct 2022 22:03:07 +0000 (23:03 +0100)]
mediatek: clean up platform kernel modules
Remove kmod-sdhci-mtk as the mtk-sd driver is built-in anyway for the
relevant subtargets in order to support mounting rootfs from eMMC or
SD card.
Add kmod-iio-mt6577-auxadc to support reading the raw values from the
auxadc unit used as in-SoC thermal sensor. This driver was previously
built-in, but as thermal itself works well without it there is no use
for it in every day use of a device. Build the module to still allow
access to the raw values for those who need it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mark Mentovai [Thu, 11 Nov 2021 17:24:24 +0000 (12:24 -0500)]
ipq40xx: Convert mikrotik,wap-ac to DSA
As done previously, this preserves the MAC addresses of they physical
Ethernet ports. The interfaces are renamed as eth0 is in use for the
native GMAC; the new interface naming matches the physical port labels.
- sw-eth1 corresponds to the physical port labeled ETH1 and has the
base MAC address. This port can be used to power the device.
- sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC
address one greater than the base.
As this device has 2 physical ports, they are each connected to their
respective PHYs, allowing the link status to be visible to software.
Since they are not marked on the case with any role (such as LAN or
WAN), both are bridged to the lan network by default, although this can
easily be changed if needed.
INAGAKI Hiroshi [Wed, 19 Oct 2022 14:57:34 +0000 (23:57 +0900)]
ath79: use NVMEM for wlan caldata on ELECOM devices
Use NVMEM "calibration" implementation for ath9k/ath10k(-ct) on ELECOM
WRC-300GHBK2-I and WRC-1750GHBK2-I/C instead of mtd-cal-data property
or user-space script.
Tested-by: Mark Mentovai <mark@mentovai.com> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Tested-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de> Signed-off-by: Nick Hainke <vincent@systemli.org>
Daniel Golle [Wed, 19 Oct 2022 18:58:12 +0000 (19:58 +0100)]
mediatek: mt7622: don't rely on existing image for sysupgrade
Don't reply on mapped rootfs partition but rather just take what ever
has been set to the kernel cmdline root= parameter as a hint to decide
which media to install sysupgrade to on the BananaPi BPi-R64.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 19 Oct 2022 17:08:09 +0000 (18:08 +0100)]
mediatek: mt7622: kernel config fixes
* remove orphaned Kconfig symbol now that CONFIG_IIO is no longer
selected after commit ef8b935c95 ("mediatek: clean up mt7622 kernel config")
* select UBI fast-map feature to decrease boot time and keep the
number of spare blocks required in sync with U-Boot's expectations
(we got fast-map enabled in U-Boot)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
generic: 5.15: add missing tag for some backports patches
Add for mtd-parsers-trx-allow-to-use-on-MediaTek-MIPS-SoCs.patch and
hwmon-lm70-Add-ti-tmp125-support.patch the 5.18 tag as it was merged
in kernel 5.18.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Tue, 18 Oct 2022 19:01:23 +0000 (20:01 +0100)]
uboot-envtools: mediatek_filogic: fix BPi-R3 when no OS is installed
Fix accessing the environment in case no OS is installed on the flash
media selected for boot as this is possible when booting initramfs.
In case of relying on the device specified to be mounted as rootfs to
be present, rather just use the kernel cmdline 'root' variable as a
hint to decide where to read/write the U-Boot environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 18 Oct 2022 13:28:53 +0000 (14:28 +0100)]
uboot-mediatek: update to U-Boot 2022.10
Remove patches adding support for MT7621 which have been merged upsteam.
Patches for MT7981 and MT7986 have been merged too, but not in time to
be included in the 2022.10 release, so we have to keep carrying them
until the 2023.01 release.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hauke Mehrtens [Sat, 15 Oct 2022 10:25:19 +0000 (12:25 +0200)]
rtl8812au-ct: Fix compile
Replace the extern inline with a static inline. With extern inline the
compiler will generate the function in all compile units including this
file which breaks linking later.
Robert Marko [Tue, 27 Sep 2022 08:58:50 +0000 (10:58 +0200)]
uboot-mvebu: update to 2022.10
Update mvebu U-boot to 2022.10 to avoid backporting patches in order
to support Methode eDPU.
It also allows dropping existing patches as they are all backports.
Tested-by: Andre Heider <a.heider@gmail.com> # espressobin-v3-v5-1gb-2cs Tested-by: Russell Morris <github@rkmorris.us> # espressobin-v3-v5-1gb-1cs Tested-by: Josef Schlehofer <pepe.schlehofer@gmail.com> [Turris Omnia] Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Jo-Philipp Wich [Fri, 14 Oct 2022 15:32:28 +0000 (17:32 +0200)]
firewall4: update to latest Git HEAD
4fbf6d7 ruleset.uc: log forwarded traffic not matched by zone policies c7201a3 main.uc: reintroduce set reload restriction 756f1e2 ruleset: fix emitting set_mark/set_xmark rules with masks 3db4741 ruleset: properly handle zone names starting with a digit 43d8ef5 fw4: fix formatting of default log prefix 592ba45 main.uc: remove uneeded/wrong set reload restrictions b0a6bff tests: fix testcases 145e159 fw4: recognize `option log` and `option counter` in `config nat` sections ce050a8 fw4: fall back to device if l3_device is not available in ifstatus
Kernel loaders like the lzma-loader currently don't track changes to
their sources. This can lead to an old version of a loader to be used
when a build tree is not clean between builds.
As the loaders are tiny and the build times are insignificant, simply
force rebuilding them on every build to avoid this problem.
mpc85xx: add SPI kernel loader for TP-Link TL-WDR4900 v1
Similar to the lzma-loader on our MIPS targets, the spi-loader acts as
a second-stage loader that will then load and start the actual kernel.
As the TL-WDR4900 uses SPI-NOR and the P1010 family does not have support
for memory mapping of this type of flash, this loader needs to contain a
basic driver for the FSL ESPI controller.
Uwe Kleine-König [Fri, 14 Oct 2022 10:23:07 +0000 (12:23 +0200)]
busybox: nslookup: ensure unique transaction IDs for the DNS queries
On machines with a coarse monotonic clock (here: TP-Link RE200 powered
by a MediaTek MT7620A) it can happen that the two DNS requests (for A
and AAAA) share the same transaction ID. If this happens the second
reply is wrongly dropped and nslookup reports "No answer".
Fix this by ensuring that the transaction IDs are unique.
generic: 5.15: backport qca8k fixup patches for Big-Endian systems
Backport qca8k fixup patches for inband mgmt on Big-Endian systems.
This is needed for ath79 and mpc85xx targets that are Big-Endian and use
qca8k based switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bruno Umuarama [Fri, 14 Oct 2022 00:37:39 +0000 (00:37 +0000)]
mediatek: mt7623: fix thermal zone
Raising the temperatures for passive and active trips. @VA1DER
proposed at issue 9396 to remove passive trip. This commit relates to
his suggestion.
Without this patch. the CPU will be throttled all the way down to 98MHz
if the temperature rises even a degree above the trip point, and it was
further discovered that if the internal temperature of the device is
above the first trip point temperature when it boots then it will start
in a throttled state and even
$ echo disabled > /sys/class/thermal/thermal_zone0/mode
will have no effect.
The patch increases the passive trip point and active cooling map. The
throttling temperature will then be at 77°C and 82°C, which is still a
low enough temperature for ARM devices to not be in the real danger
zone, and gives some operational headroom.
Signed-off-by: Bruno Umuarama <anonimou_eu@hotmail.com>
Felix Fietkau [Fri, 23 Sep 2022 12:12:32 +0000 (14:12 +0200)]
mac80211: change default ifname to <phy>-<type><index>
This makes it clear, which phy a wlan device belongs to and also helps with
telling them apart by including the mode in the ifname.
Preparation for automatically renaming PHYs
Felix Fietkau [Fri, 30 Sep 2022 17:19:51 +0000 (19:19 +0200)]
base-files: add helper functions for adding wlan device entries to board.json
These will be used to give WLAN PHYs a specific name based on path specified
in board.json. The platform board.d script can assign a specific order based
on available slots (PCIe slots, WMAC device) and device tree configuration.
This helps with maintaining config compatibility in case the device path
changes due to kernel upgrades.
Felix Fietkau [Thu, 13 Oct 2022 19:49:38 +0000 (21:49 +0200)]
mac80211: fix typo in netifd script
Reported-by: Chad Monroe <chad.monroe@smartrg.com> Fixes: 590eaaeed59a ("mac80211: fix issues in HE capabilities") Signed-off-by: Felix Fietkau <nbd@nbd.name>
Nick Hainke [Sun, 11 Sep 2022 19:53:20 +0000 (21:53 +0200)]
airoha: fix imagebuilder generation by introducing generic target
The generic imagebuilder does not have a generic in the name, although
this is the default naming scheme. Apply the same fix as for the octeon
target. Thanks to @dangowrt for reporting that the same issues applies
also for the airoha target.
Before the fix:
openwrt-imagebuilder-airoha.Linux-x86_64.tar.xz
Nick Hainke [Sat, 8 Jan 2022 07:55:21 +0000 (08:55 +0100)]
hostapd: add measurement report value for beacon reports
Add the measurement report value to the beacon reports send via ubus. It
is possible to derive from the measurement report if a station refused to
do a beacon report and why. It is important to know why a station refuses
to do a beacon-report. In particular, we should not request a beacon
report from a station again that refused a beacon-report before.
The rejection reasons can be found by looking at the bits defined by:
- MEASUREMENT_REPORT_MODE_ACCEPT
- MEASUREMENT_REPORT_MODE_REJECT_LATE
- MEASUREMENT_REPORT_MODE_REJECT_INCAPABLE
- MEASUREMENT_REPORT_MODE_REJECT_REFUSED
Suggested-by: Ian Clowes <clowes_ian@hotmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
Upstream has switched to gnu11 not too long ago. One advantage of
backporting this to these older kernels is, that we can encourage and
write better upstreamable kernels. E.g. the kernel devs prefer loop
declarations. Shrinking the master/local gap will be useful in these
cases.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Huangbin Zhan [Tue, 29 Mar 2022 16:15:29 +0000 (00:15 +0800)]
build: image: use printf for ModelNameLimit16
Fix syntax error on macos, for substr is undefined results according to
the POSIX standard.
From expr on macos:
According to the POSIX standard, the use of string arguments length,
substr, index, or match produces undefined results. In this version of
expr, these arguments are treated just as their respective string values.
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
[ wrap commit description to 80 columns and improve it ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Felix Fietkau [Mon, 10 Oct 2022 20:50:35 +0000 (22:50 +0200)]
mac80211: fix issues in HE capabilities
Enable HE SU beamformee by default
Fix spatial reuse configuration:
- he_spr_sr_control is not a bool for enabling, it contains multiple bits
which disable features that should be disabled by default
- one of the features (PSR) can be enabled through he_spr_psr_enabled
- add option to disable bss color / spatial reuse
projects / thirdparty / openwrt.git / log
