Shiji Yang [Thu, 1 Dec 2022 10:49:45 +0000 (18:49 +0800)]
ramips: use default lzma dictionary size for better performance
limit dictionary size patch was introduced to solve the well known
"LZMA ERROR 1 - must RESET board to recover" error. 09b6755946409d8fd8 "ramips: limit dictionary size for lzma compression"
It seems that it has failed recently and we can use lzma loader to fix
this error by adding "$(Device/uimage-lzma-loader)". So just remove it
to use the default parameter -d24 for a higher compression ratio.
Rafał Miłecki [Thu, 5 Jan 2023 12:33:18 +0000 (13:33 +0100)]
kernel: fix bugs added with mac-address-ascii support
1. Check for -EPROBE_DEFER
If it occurs we have to return immediately. Trying other properties
could result in another error and ignoring -EPROBE_DEFER which has a
special meaning.
2. Check for read result
Assuming property->read() success can result in NULL pointer
dereference. It happens e.g. for "mac-address" with NVMEM cell
containing invalid MAC.
3. Simplify code
Don't move cell reading & nvmem_cell_put() into a loop. Simplify loop
code.
David Bauer [Thu, 17 Nov 2022 21:53:33 +0000 (22:53 +0100)]
ath79: combine UniFi AC dual firmware-partitions
In order to maximize the available space on UniFi AC boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.
This allows users to access more usable space for additional packages.
Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single kernel
partition in the future.
David Bauer [Thu, 17 Nov 2022 22:02:13 +0000 (23:02 +0100)]
ramips: combine USW-Flex dual firmware-partitions
In order to maximize the available space on USW-Flex boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.
This allows users to access more usable space for additional packages.
Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single kernel
partition in the future.
David Bauer [Tue, 15 Nov 2022 14:25:40 +0000 (15:25 +0100)]
ath79: combine OCEDO dual firmware-partitions
In order to maximize the available space on OCEDO boards using a
dual-image partition layout, combine the two OS partitions into a single
partition.
This allows users to access more usable space for additional packages.
Don't limit the usable image size to the size of a single OS partition.
The initial installation has to be done with an older version of OpenWrt
in case the generated image exceeds the space of a single OS
partition in the future.
Enrico Mioso [Sun, 20 Nov 2022 04:19:06 +0000 (05:19 +0100)]
mvebu: harmonize GL.iNet GL-MV1000 MTD partitions layout with vendor
The GL-MV1000 ships with a 16MB spi-nor flash, containing a copy of the stock GL.iNet firmware.
Add the corresponding flash areas, so our view matches the one of the in-flash stock firmware.
MAC
LAN b4:4b:d6:2e:c7:b0 (label)
WAN b4:4b:d6:2e:c7:b1
WiFi 2.4 00:0c:43:26:46:08
WiFi 5 00:0c:43:26:59:97
Installation
There are two known options:
1) The Luci-based UI.
2) Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
The openwrt image supplied by cudy is signed and can be used to
install unsigned images.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
The EN25QH256A variant of the EN25QH256 doesn't initialize correctly from SFDP
alone and only accesses memory below 8m (addr_width is 4 but read_opcode takes
only 3 bytes).
Set SNOR_F_4B_OPCODES if the flash chip variant was detected using hwcaps.
The fix submitted upstream uses the PARSE_SFDP initializer that is not
available in the kernel used with Openwrt.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Florian Eckert [Wed, 18 Aug 2021 15:19:15 +0000 (17:19 +0200)]
target/imagebuilder: add depends target to show all package that gets installed
This commits adds the makefile targets `depends` this wrapper is a call
to `opkg depends`. This command shows which runtime dependencies exist
if this package is installed into the image.
Notes:
- The device supports dual boot mode
- The firmware partitions were concatinated into one
- The FN button led indicator has been reassigned as the 2.4GHz
wifi indicator.
Flash instruction:
The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-keenetic_kn-1613-squashfs-factory.bin"
to "KN-1613_recovery.bin" and place it in tftp server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power led start blinking.
4. Router will download file from server, write it to flash and reboot.
Nick Hainke [Thu, 5 Jan 2023 10:08:27 +0000 (11:08 +0100)]
libpcap: update to 1.20.2
A huge rewrite in libpcap was introduced by dc14a7babca1 ("rpcap: have
the server tell the client its byte order.") [0]. The patch
"201-space_optimization.patch" does not apply at all anymore. So remove
it.
Note: ethernet LEDs are not enabled
because a new netifd hotplug is required
in order to operate like OEM.
Board has 1 amber and 1 green
for each of the 3 case viewports.
**MAC addresses:**
1 MAC Address in flash at end of uboot
ASCII encoded, no delimiters
Labeled as "MAC Address" on case
OEM firmware sets offsets 1 and 8 for wlan
Pins are populated with a header and traces not blocked.
Bootloader is set to 9600 baud, 8 data, 1 stop.
**Console Access:**
Bootloader:
Interrupt boot with Ctrl+C
Press "k" and enter password "1"
OR
Hold reset button for 5 sec during power on
Interrupt the TFTP transfer with Ctrl+C
to print commands available, enter "help"
OEM:
default username is "admin", password blank
telnet is available at default address 192.168.1.2
serial is available with baud 9600
to print commands available, enter "help"
or tab-tab (busybox list of commands)
**Installation:**
Use factory.bin with OEM upgrade procedures
OR
Use initramfs.bin with uboot TFTP commands.
Then perform a sysupgrade with sysupgrade.bin
**TFTP Recovery:**
Using serial console, load initramfs.bin using TFTP
to boot openwrt without touching the flash.
TFTP is not reliable due to bugged bootloader,
set MTU to 600 and try many times.
If your TFTP server supports setting block size,
higher block size is better.
Splitting the file into 1 MB parts may be necessary
The best way to return to OEM firmware
is to have a copy of the MTD partitions
before flashing Openwrt.
Backup copies should be made of partitions
"fwconcat0", "loader", and "fwconcat1"
which together is the same flash range
as OEM's "rootfs" and "uimage"
by loading an initramfs.bin
and using LuCI to download the mtdblocks.
It is also possible to extract from the
OEM firmware upgrade image by splitting it up
in parts of lengths that correspond
to the partitions in openwrt
and write them to flash,
after gzip decompression.
After writing to the firmware partitions,
erase the "reserved" partition and reboot.
**OEM firmware image format:**
Images from Fortinet for this device
ending with the suffix .out
are actually a .gz file
The gzip metadata stores the original filename
before compression, which is a special string
used to verify the image during OEM upgrade.
After gzip decompression, the resulting file
is an exact copy of the MTD partitions
"rootfs" and "uimage" combined in the same order and size
that they appear in /proc/mtd and as they are on flash.
OEM upgrade is performed by a customized busybox
with the command "upgrade".
Another binary, "restore"
is a wrapper for busybox's "tftp" and "upgrade".
Michael Pratt [Sat, 10 Dec 2022 11:34:54 +0000 (06:34 -0500)]
base-files: rework mtd_get_mac_text()
It's necessary to be able to specify the length
for MAC addresses that are stored in flash, for example,
in a case where it is stored without any delimiter.
Michael Pratt [Fri, 9 Dec 2022 22:47:11 +0000 (17:47 -0500)]
ath79: allow skipping hash for Senao sysupgrade
Some vendors of Senao boards have a similar flash layout
situation that causes the need to split the firmware partition
and use the lzma-loader, but do not store
checksums of the partitions or otherwise
do not even have a uboot environment partition.
Make sure functions calling rtl838x_smi_wait_op() return its return
value in target/linux/realtek/files-5.15/drivers/net/dsa/rtl83xx/rtl838x.c.
This brings the code style in line with the rtl839x implementation.
Pascal Ernster [Tue, 3 Jan 2023 22:01:11 +0000 (23:01 +0100)]
realtek: return correct error value for phy ops
A behavioural change was introduced with commit 758c88b96963 ("realtek:
Whitespace and codestyle cleanup") causing rtl838x_read_phy() and
rtl838x_write_phy() to unconditionally return -ETIMEDOUT. As a result,
probing the device during boot fails:
Error setting up netdev, freeing it again.
rtl838x-eth: probe of 1b00a300.ethernet failed with error -5
Fix the bootloop caused by this regression with kernel 5.15 on rtl838x
devices, by properly returning 0 on success.
Tested on a Netgear GS108T v3, a Netgear GS310TP v1, a Zyxel GS1900-8HP
v1 and an HPE 1920-8G.
Fixes: 758c88b969639d0e6b684669d2e54dd1be3102f4 ("realtek: Whitespace and codestyle cleanup") Tested-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Pascal Ernster <git@hardfalcon.net>
realtek: Migrate to upstream generic MIPS addresses
Upstream generic MIPS uses 0x80100000 and 0x80100400 for the LOADADDR
and ENTRY addresses. As we do not want to diverge from upstream and
patch upstream when not needed, adjust our addresses as well to be
future proof.
Florian Maurer [Mon, 26 Dec 2022 23:30:07 +0000 (00:30 +0100)]
lantiq-xrx200: fix wan LED on o2 box 6431
The WIFI LED already worked for me with the latest openwrt 22.03 version.
Wifi LED did not with an older 22.x version (in gluon - there phy0radio did nothing but phy0tpt did show activity
the WAN interface has the name "wan" and not "pppoe-wan" on this device
Linhui Liu [Sun, 25 Dec 2022 03:57:35 +0000 (11:57 +0800)]
toolchain/nasm: update to 2.16.01
ChangeLog:
Version 2.16.01
_This is a documentation update release only._
(*) Fix the creation of the table of contents in the HTML version of
the documentation.
Version 2.16
(*) Support for the `rdf' format has been discontinued and all the
RDOFF utilities has been removed.
(*) The `--reproducible' option now leaves the filename field in the
COFF object format blank. This was always rather useless since
it is only 18 characters long; as such debug formats have to
carry their own filename information anyway.
(*) Fix handling of MASM-syntax reserved memory (e.g. `dw ?') when
used in structure definitions.
(*) The preprocessor now supports functions, which can be less
verbose and more convenient than the equivalent code implemented
using directives. See section 4.4.
(*) Fix the handling of `%00' in the preprocessor.
(*) Fix incorrect handling of path names affecting error messages,
dependency generation, and debug format output.
(*) Support for the RDOFF output format and the RDOFF tools have
been removed. The RDOFF tools had already been broken since at
least NASM 2.14. For flat code the ELF output format
recommended; for segmented code the `obj' (OMF) output format.
(*) New facility: preprocessor functions. Preprocessor functions,
which are expanded similarly to single-line macros, can greatly
simplify code that in the past would have required a lengthy
list of directives and intermediate macros. See section 4.4.
(*) Single-line macros can now declare parameters (using a `&&'
prefix) that creates a quoted string, but does _not_ requote an
already quoted string. See section 4.2.1.
(*) Instruction table updated per public information available as of
November 2022.
(*) All warnings in the preprocessor have now been assigned warning
classes. See appendix A.
(*) Fix the invalid use of `RELA'-type relocations instead of `REL'-
type relocations when generating DWARF debug information for the
`elf32' output format.
(*) Fix the handling `at' in `istruc' when the structure contains
local labels. See section 5.9.2.
(*) When assembling with `--reproducible', don't encode the filename
in the COFF header for the `coff', `win32' or `win64' output
formats. The COFF header only has space for an 18-character
filename, which makes this field rather useless in the first
place. Debug output data, if enabled, is not affected.
(*) Fix incorrect size calculation when using MASM syntax for non-
byte reservations (e.g. `dw ?'.)
(*) Allow forcing an instruction in 64-bit mode to have a (possibly
redundant) REX prefix, using the syntax `{rex}' as a prefix.
(*) Add a `{vex}' prefix to enforce VEX (AVX) encoding of an
instruction, either using the 2- or 3-byte VEX prefixes.
(*) The `CPU' directive has been augmented to allow control of
generation of VEX (AVX) versus EVEX (AVX-512) instruction
formats, see section 7.11.
(*) Some recent instructions that previously have been only
available using EVEX encodings are now also encodable using VEX
(AVX) encodings. For backwards compatibility these encodings are
not enabled by default, but can be generated either via an
explicit `{vex}' prefix or by specifying either `CPU LATEVEX' or
`CPU NOEVEX'; see section 7.11.
(*) Document the already existing `%unimacro' directive. See section
4.5.12.
(*) Fix a code range generation bug in the DWARF debug format
(incorrect information in the `DW_AT_high_pc' field) for the ELF
output formats. This bug happened to cancel out with a bug in
older versions of the GNU binutils linker, but breaks with other
linkers and updated or other linkers that expect the spec to be
followed.
(*) Fix segment symbols with addends, e.g. `jmp _TEXT+10h:0' in
output formats that support segment relocations, e.g. the `obj'
format.
(*) Fix various crashes and hangs on invalid input.
Nikolay Martynov [Thu, 15 Dec 2022 01:26:38 +0000 (20:26 -0500)]
ramips: add basic support for tp-link er605-v2
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
The board has headers to attach console. In order for them to work two solder
bridges near those pads need to be made.
`firmware` partition contains UBI volumes. Unfortunately I accidentally wiped
partition and I no longer have access to it.
`firmware` partition contains 'secondary' U-Boot which is run by 'first' u-boot.
It also contains various configuration partitions that include device info and
MAC address. There also seems to be 'primary' and 'backup' set of 'main' volumes.
U-boot has `mtkupgrade` command that just overrides data on firmware partitions.
Firmware file provided by TP-Link cannot be used with that command.
U-boot also has 'recovery' http server. Unfortunately I was not able to make it
work with manufacturer's firmware.
Manufacturer's firmware essentially contains multiple UBI volumes along with
'partition table'. Unfortunately I no longer can properly run manufacturer's
firmware so I cannot at the moment try to a support for building 'factory' images.
This patch adds support for initramfs image as well as sysupgrade image.
This seems to be pretty standard MT7621 board otherwise.
Things that work:
* network
* leds
* usb
* factory MAC detection
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
This patch adds the missing LEDs to Asus RT-AX53U.
Based on PR #10400 and patch provided in #11068
- enable the two LEDs controlled by mt7915e for wireless;
- add label to power LED so it works properly and fix formatting;
- add the USB LED;
- switch LEDs are best left to be controlled by hardware for now.
Co-Authored-By: Ivan Rozhuk <rozhuk.im@gmail.com> Co-Authored-By: Shiji Yang <yangshiji66@qq.com> Co-Authored-By: Hartmut Birr <e9hack@gmail.com> Tested-by: Felix Baumann <felix.bau@gmx.de> Tested-by: Marian Sarcinschi <znevna@gmail.com> Signed-off-by: Marian Sarcinschi <znevna@gmail.com>
Bjoern Dobe [Thu, 29 Dec 2022 17:19:37 +0000 (18:19 +0100)]
ipq40xx: fix wlan mac address for Aruba AP-303H
Assigns the correct mac address from nvmen to the wlan interfaces.
This Mac address corresponds to the label "Wireless MAC" on the device
and the stock firmware.
Removes duplicate entry of calibration variant for both radios.
Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
generic: 5.10: backport Treat IPv4 segment's lowest address as unicast
Backport patch from kernel 5.14.
Treat only the highest, not the lowest, IPv4 address within a local
subnet as a broadcast address, as subnets do not need two different
broadcast addresses and networking documentation consistently prefers
the highest address as broadcast.
This patch was merged in upstream net-next tree in May 2021 at
This eventually frees up one address per subnet. It matches behavior
suggested in our Internet-Draft, and also the default behavior of OpenBSD
and FreeBSD.
Signed-off-by: Seth David Schoen <schoen@loyalty.org>
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=c160505c9b574b346031fdf2c649d19e7939ca11
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=a051e10bfc6906d29dae7a31f0773f2702edfe1b
3. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.86&id=ec1727f89ecd6f2252c0c75e200058819f7ce47a
4. Quilt gave this output when I applied the patch to rebase it:
% quilt push -f
Applying patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch
patching file arch/mips/ralink/Kconfig
patching file drivers/pci/controller/Kconfig
patching file drivers/pci/controller/Makefile
patching file drivers/staging/Kconfig
patching file drivers/staging/Makefile
patching file drivers/staging/mt7621-pci/Kconfig
patching file drivers/staging/mt7621-pci/Makefile
patching file drivers/staging/mt7621-pci/TODO
patching file drivers/staging/mt7621-pci/mediatek,mt7621-pci.txt
patching file drivers/staging/mt7621-pci/pci-mt7621.c
Hunk #1 FAILED at 1.
Not deleting file drivers/staging/mt7621-pci/pci-mt7621.c as content differs from patch
1 out of 1 hunk FAILED -- saving rejects to file drivers/staging/mt7621-pci/pci-mt7621.c.rej
patching file drivers/pci/controller/pcie-mt7621.c
Applied patch platform/100-PCI-mt7621-Add-MediaTek-MT7621-PCIe-host-controller-.patch (forced; needs refresh)
Upon inspecting drivers/staging/mt7621-pci/pci-mt7621.c.rej, it seems that
the original patch wants to delete drivers/staging/mt7621-pci/pci-mt7621.c
but upstream's version was not an exact match. I opted to delete that
file.
5. Suggestion by hauke: https://github.com/torvalds/linux/commit/19098934f910b4d47cb30251dd39ffa57bef9523
"This patch is in upstream kernel, but it was backported to the old
staging driver in kernel 5.15."
Robert Marko [Sun, 1 Jan 2023 13:24:06 +0000 (14:24 +0100)]
oxnas: sata_oxnas: use ata_link_err
Kernel 5.15.86 has backported ("ata: libata: move ata_{port,link,dev}_dbg
to standard pr_XXX() macros") and this is now causing compilation errors
for oxnas SATA driver due to usage of ata_link_printk().
Upstream has migrated to using the appropriate
ata_link_{err, warn, notice, info} calls a while ago so its not affected.
Lets do the same for oxnas SATA driver and use ata_link_err() instead of
ata_link_printk().
Nick Hainke [Mon, 3 Oct 2022 10:32:06 +0000 (12:32 +0200)]
zynq: add 5.15 testing kernel
Enable testing kernel.
Reviewed-by: Luis Araneda <luaraneda@gmail.com> Tested-by: Luis Araneda <luaraneda@gmail.com> (Digilent Zybo Z7-20) Signed-off-by: Nick Hainke <vincent@systemli.org>
Olliver Schinagl [Wed, 14 Dec 2022 14:16:33 +0000 (15:16 +0100)]
realtek: Migrate to libdeflate
Libdeflate is a more advanced gzip compressor, which allows for faster
decompression, higher compression speed (factor 3-4), while being fully
gzip compatible.
Several devices provide U-Boot versions with only gzip compressed kernel
support (e.g. Realtek switches). This compression method produces larger
images than lzma. To save space on flash and avoid going the hard way with
lzma-loader we can make use of enhanced gzip tool based on libdeflate
compression library from https://github.com/ebiggers/libdeflate. It
keeps 100% deflate/gzip compatibility while improving compression ratio.
The image can be unpacked by the default inflate routines inside U-Boot.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[Switched to v1.15 and made it work with cmake] Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Rosen Penev <rosenp@gmail.com> Reviewed-by: Sander Vanheule <sander@svanheule.net>
Hauke Mehrtens [Sat, 31 Dec 2022 18:32:41 +0000 (19:32 +0100)]
treewide: Trigger reinstall of all wolfssl dependencies
The ABI of the wolfssl library changed a bit between version 5.5.3 and
5.5.4. This release update will trigger a rebuild of all packages which
are using wolfssl to make sure they are adapted to the new ABI.
Hauke Mehrtens [Sat, 31 Dec 2022 20:11:35 +0000 (21:11 +0100)]
toolchain/binutils: backport stable patches
Add the patches with real changes from the binutils 2.39 stable branch.
I am not aware that we ran into any of these problems, but I think it is
better to take the existing stable patches.
They were exported like this:
git format-patch binutils-2_39...origin/binutils-2_39-branch
I removed the patches changing the version numbers only.
Hauke Mehrtens [Wed, 28 Dec 2022 00:11:45 +0000 (01:11 +0100)]
tfa-layerscape: Use trusted-firmware-a.mk
This converts the trusted firmware arm build Makefile to make use of
the common trusted-firmware-a.mk file. This also fixes the build with
binutils 2.39.
Hauke Mehrtens [Mon, 26 Dec 2022 23:28:03 +0000 (00:28 +0100)]
arm-trusted-firmware-mvebu: Use host flags for cryptest compilation
Without these changes it used the system LDFLAGS for the compilation of
the cryptopp library. This does not always work when we add
"-no-warn-rwx-segments" which is done to support binutils 2.39 inside of
OpenWrt.
Allow forced flashing of a factory firmware image, after checking for the
correct FIT magic header and Linksys board-specific footer. Details of the
footer are already described in scripts/linksys-image.sh.
This is convenient as it avoids using a TFTP server or OEM GUI, and allows
restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA
migration and kernel repartition) directly from the command line.
Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01.
Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> # WHW01 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Tue, 6 Dec 2022 03:38:45 +0000 (19:38 -0800)]
ipq40xx: migrate Linksys WHW01 to DSA and re-enable
Convert Linksys WHW01 network configuration to DSA and re-enable builds.
Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Tony Ambardar [Tue, 6 Dec 2022 03:44:32 +0000 (19:44 -0800)]
ipq40xx: fix up Linksys WHW01 board name, device definition
Update the board name defined in DTS to match online documentation and the
name encoded into factory firmware. This helps supports flashing firmware
factory images using 'sysupgrade'.
Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB
instead of the correct 74 MB, and defines factory images which include
extra adjustments/padding that do not match OEM factory images and may
cause problems flashing. Update image size and build recipe to fix these.
Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300,
and correspondingly reduce the rootfs size by 2 MB:
* modify partition definitions in related .dts files
* modify device kernel/image sizes in generic.mk
Update to compat-version 2.0 to force factory image usage on sysupgrade,
noting the current version 1.1 is an unreleased update for DSA migration.
Also update the compat-version message, explaining the need to run one of
the following console commands to update U-Boot's kernel-size variable
before flashing the OpenWrt factory image.
setenv kernsize 500000 ; saveenv # (U-Boot serial console)
Finally, re-enable the 3 devices.
Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Hauke Mehrtens [Thu, 29 Dec 2022 20:26:28 +0000 (21:26 +0100)]
mbedtls: update to version 2.28.2
Changelog: https://github.com/Mbed-TLS/mbedtls/releases/tag/v2.28.2
This release of Mbed TLS provides bug fixes and minor enhancements. This
release includes fixes for security issues.
Fixes the following CVEs:
* CVE-2022-46393: Fix potential heap buffer overread and overwrite in
DTLS if MBEDTLS_SSL_DTLS_CONNECTION_ID is enabled and
MBEDTLS_SSL_CID_IN_LEN_MAX > 2 * MBEDTLS_SSL_CID_OUT_LEN_MAX.
* CVE-2022-46392: An adversary with access to precise enough information
about memory accesses (typically, an untrusted operating system
attacking a secure enclave) could recover an RSA private key after
observing the victim performing a single private-key operation if the
window size used for the exponentiation was 3 or smaller.
Felix Fietkau [Fri, 30 Dec 2022 15:42:03 +0000 (16:42 +0100)]
netifd: update to the latest version
2cffe0c44e62 treewide: correctly apply IFNAMSIZ limit 96bcbb2e4eb6 wireless: allow set_retry ubus notify command to trigger a wdev restart a2e8cd75dbf6 wireless: add support for disabling multicast-to-unicast per virtual interface e9f44189ade7 system: move netdev types to system-linux.c where they are used a3fab0119ef1 utils: include utils.h last 7ce73fc16765 vlandev: propagate topology changes 81c1fbcba2f2 device: fix vlan device issues with disappearing lower devices
Hauke Mehrtens [Thu, 29 Dec 2022 16:40:02 +0000 (17:40 +0100)]
CI: labeler: Add target label to target packages
This adds the target label also to changes in packages which are target
specific like the boot loader of a target or some drivers which are only
use on one target.
Chuanhong Guo [Fri, 30 Dec 2022 07:55:56 +0000 (15:55 +0800)]
mediatek: drop redmi-ax6000 variant with modified env
This variant uses xiaomi factory u-boot and modified u-boot-env &
bootcmd.
By modifying uboot-env, the xiaomi firmware recovery provided in
the vendor u-boot doesn't work anymore. It's possible to put
u-boot into a state where it refuese to take any serial input.
If the u-boot is in this state, users can't restore their
firmware without taking the flash off the board.
We now have a -stock variant where the vendor u-boot is used in
a way that xiaomi firmware recovery still works, and a -ubootmod
variant where we get rid of all xiaomi components, have more
usable space and no uart console lock. These two should cover all
use cases and we don't need this variant anymore.
Drop this redmi-ax6000 variant. Existing users of this variant
should perform a u-boot mod or restore to the -stock layout.
Hauke Mehrtens [Sun, 18 Dec 2022 16:32:46 +0000 (17:32 +0100)]
tree-wide: Do not use package librt and libpthread
The libraries libpthread, libdl, libutil, libanl have been integrated
into the libc library in version 2.34. it is not needed to explicitly
link them any more.
Most of the functions have been moved from the librt.so into libc.so
some time ago already.
Šimon Bořek [Wed, 15 Jun 2022 15:38:38 +0000 (17:38 +0200)]
mpc85xx: change CPU_TYPE from 8540 to 8548
All subtargets as p1010, p1020, p2020 uses e500v2 cores [1] [2] [3] [4],
so let's force cpu type to 8545 for all mpc85xx target even though
there might exist device with e500v1, but there is no such router supported in OpenWrt
and because of that it does not make sense to to set CPU_TYPE for each subtarget.
All MPC85xx SoC can be found here:
https://www.nxp.com/products/processors-and-microcontrollers/legacy-mpu-mcus/powerquicc-processors:POWERQUICC_HOME#powerquicc-iii-mpc85xx
Šimon Bořek [Wed, 15 Jun 2022 15:31:39 +0000 (17:31 +0200)]
mpc85xx: add support for cpu type 8548
8540 cpu type corresponds to e500v1 core while
8548 cpu type corresponds to e500v2 core
See https://www.nxp.com/products/processors-and-microcontrollers/legacy-mpu-mcus/powerquicc-processors:POWERQUICC_HOME#powerquicc-iii-mpc85xx
and https://www.nxp.com/docs/en/application-note/AN2807.pdf .
Robert Marko [Wed, 28 Dec 2022 21:57:49 +0000 (22:57 +0100)]
linux-firmware: disable stripping
It has been brought to my attention that recently added WCN6855 firmware
is broken as it is getting stripped during building due to being 2 ELF
binaries.
I am sure WCN6750 and any other ELF binaries are having the same issue,
so since stripping firmware binaries is clearly unwanted disable it.
Fixes: b4d3694f81f4 ("linux-firmware: package ath11k consumer cards firmware") Signed-off-by: Robert Marko <robimarko@gmail.com>
5. Load kmod-mtd-rw to temporarily make the bootloader partions writable.
The kmod-mtd-rw is from the feeds, it is not packed in initramfs-factory
by default.
To install kmod-mtd-rw via opkg:
opkg update && opkg install kmod-mtd-rw
Or, download kmod-mtd-rw.ipk from OpenWrt server and install it manually
e.g:
https://downloads.openwrt.org/snapshots/targets/mediatek/filogic/kmods/
Select your OpenWrt release version and kernel version accordingly.
8. This is optional. Skip this if you do not want to have NAND recovery
boot feature offered by OpenWrt U-Boot. Don't worry, you always have
automatic tftp recovery feature enabled.
Sander Vanheule [Wed, 28 Dec 2022 20:39:46 +0000 (21:39 +0100)]
realtek: deduplicate GS1900 recipes
ZyXEL GS1900 devices with SoCs from both the RTL838x and RTL839x
families share the same image structure and size of the firmware
partition. Additionally, the GS1900-48 recipe provided a parameter for
the zyxel-vers command, but this parameter is not used. Deduplicate the
recipes by moving it to target/linux/realtek/image/common.mk.
Sander Vanheule [Wed, 28 Dec 2022 11:26:21 +0000 (12:26 +0100)]
realtek: fix GS1900-48 firwmare partition
The listed partition size doesn't match the original partition size, and
actually overlaps with the following partition. The partition node name
for the "firmware" partition also has an extra 'b' compared to the
partition offset.
Fixes: 47f5a0a3eed5 ("realtek: Add support for ZyXEL GS1900-48 Switch") Signed-off-by: Sander Vanheule <sander@svanheule.net>
Sander Vanheule [Tue, 27 Dec 2022 13:27:44 +0000 (14:27 +0100)]
realtek: fix ZYXELS_VERS for GS1900-48
The GS1900-48 firmware image is identified by the 'AAHN' ID, while the
GS1900-48HP is identified by 'AAHO' [1]. The latter was used, resulting
in the following error message when upgrading via the stock web UI:
Device only can support firmware from V1.00(AAHN.0) and later version
Sander Vanheule [Wed, 28 Dec 2022 20:46:48 +0000 (21:46 +0100)]
realtek: fix default image generation
While cleaning up the makefiles for the realtek target, the order of the
default image generating commands was accidentally changed. This caused
the image signature to end up somewhere in the middle, misaligning the
rootfs. As a result, sysupgrade couldn't verify upgrade images anymore,
and devices end up in a boot loop due to the unaligned (and not found)
rootfs.
Nick Hainke [Tue, 20 Dec 2022 15:12:48 +0000 (16:12 +0100)]
ath79: fix calibration-art for some boards
"0x1000" looks suspicious. By looking at data provided
by @DragonBluep I was able to identify the correct size for
AR9380, AR9287 WiFis. Furthermore, PowerCloud Systems CAP324
has a AR9344 WiFi.
projects / thirdparty / openwrt.git / log
