1. Rebase by Kevin 'ldir' Darbyshire-Bryant<ldir@darbyshire-bryant.me.uk>
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.81&id=8db9e60cdfdae5b049e32e82323da8f0f989066a
David Bauer [Fri, 9 Dec 2022 00:58:03 +0000 (01:58 +0100)]
ath79: fix Teltonika RUT230 v1 MAC assignment
The MAC-Address setup for the Teltonika RUT230 v1 was swapped for the
LAN / WAN ports. Also the Label-MAC was assigned incorrect, as the WiFi
MAC is printed on the case as part of the SSID, however only the LAN
MAC-Address is designated as a MAC-Address.
Andreas Böhler [Sat, 19 Nov 2022 23:43:50 +0000 (00:43 +0100)]
realtek: d-link: add support for dgs-1210-28mp-f
General hardware info:
----------------------
D-Link DGS-1210-28MP rev. F1 is a switch with 24 ethernet ports and 4
combo ports, all ports Gbit capable. It is based on a RTL8382 SoC @ 500MHz,
DRAM 128MB and 32MB flash. 24 ethernet ports are 802.3af/at PoE capable
with a total PoE power budget of 370W.
Power over Ethernet:
--------------------
The PSE hardware consists of three BCM59121 PSE chips, serving 8 ports
each. They are controlled by a Nuvoton MCU.
In order to enable PoE, the realtek-poe package is required. It is
installed by default, but currently it requires the manual editing of
/etc/config/poe. Keep in mind that the port number assignment does not
match on this switch, alway 8 ports are in reversed order: 8-1, 16-9 and
24-17.
LEDs and Buttons:
-----------------
On stock firmware, the mode button is supposed to switch the LED indicators
of all port LEDs between Link Activity and PoE status. The currently
selected mode is visualized using the respective LEDs. PoE Max indicates
that the maximum PoE budget has been reached.
Since there is currently no support for this behavior, these LEDs and
the mode button can be used independently.
Serial connection:
------------------
The UART for the SoC (115200 8N1) is available via unpopulated standard
0.1" pin header marked J6. Pin1 is marked with arrow and square.
Pin 1: Vcc 3.3V
Pin 2: Tx
Pin 3: Rx
Pin 4: Gnd
OEM installation from Web Interface:
------------------------------------
1. Make sure you are booting using OEM in image 2 slot. If not, switch to
image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image in vendor firmware via Tools > Backup / Upgrade
Firmware > image1
3. Toogle startup image via System > Firmware Information > Boot from
image1
4. Tools > reboot
Other installation methods not tested, but since the device shares the
board with the DGS-1210-28, the following should work:
Boot initramfs image from U-Boot:
---------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000
openwrt-rtl838x-generic-d-link_dgs-1210-28mp-f-initramfs-kernel.bin`
command
5. Boot the image with `bootm` command
Hauke Mehrtens [Thu, 8 Dec 2022 00:15:11 +0000 (01:15 +0100)]
ustream-ssl: update to Git version 2022-12-07
9217ab4 ustream-openssl: Disable renegotiation in TLSv1.2 and earlier 2ce1d48 ci: fix building with i.MX6 SDK 584f1f6 ustream-openssl: wolfSSL: provide detailed information in debug builds aa8c48e cmake: add a possibility to set library version
CI: build: skip sdk adapt to external toolchain on cache hit
On cache hit, skip sdk adapt to external toolchain. This is needed because we
cache the already extracted sdk and that is already adapted to be used
as external toolchain.
Rerunning the adap step will result in the test to fail for missing file
as the file are already got wrapped to the external toolchain format.
Fixes: 42f0ab028e2e ("CI: build: fix use of sdk as toolchain") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Wavlink WS-WN572HP3 4G is an 802.11ac
dual-band outdoor router with LTE support.
Specifications;
* Soc: MT7621DAT
* RAM: 128MiB
* Flash: NOR 16MiB GD-25Q128ESIG3
* Wi-Fi:
* MT7613BEN: 5GHz
* MT7603EN: 2.4GHz
* Ethernet: 2x 1GbE
* USB: None - only used internally
* LTE Modem: Quectel EC200T-EU
* UART: 115200 baud
* LEDs:
* 7 blue at the front
* 1 Power
* 2 LAN / WAN
* 1 Status
* 3 RSSI (annotated 4G)
* 1 green at the bottom (4G LED)
* Buttons: 1 reset button
Installation:
* press and hold the reset button while powering on the device
* keep it pressed for ten seconds
* connect to 192.168.10.1 via webbrowser (chromium/chrome works, at
least Firefox 106.0.3 does not)
* upload the sysupgrade image, confirm the checksum, wait 2 minutes
until the device reboots
Revert to stock firmware:
* same as installation but use the recovery image for WL-WN572HP3
David Bauer [Thu, 17 Nov 2022 21:48:10 +0000 (22:48 +0100)]
ramips: define loadaddr for all UniFi devices
Define the load-address for the DTB of all Ubiquiti UniFi devices using
FIT images. From the GPL code we can assume these boards are affected by
the same relocating issue with the vendor bootloader.
Daniel Golle [Wed, 7 Dec 2022 00:34:55 +0000 (00:34 +0000)]
mediatek: remove redundant flash entry from dtsi
Splitting-off the common parts of Ruijie RG-EW3200GX PRO and
reyee AX3200-E5 went wrong because the flash descriptiom was kept
also in the dtsi. Remove it there, as flash definition is added by
both board dts files.
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The toolchain included in a sdk have a different format than an external
toolchain tar.
Since sdk is a more integrated setup doesn't use and include wrapper bin
that use the external toolchain config and use an alternative and more
standard way to include all the toolchain headers.
External toolchain use wrapper.sh to append the configured include
header when each tool is called.
Fix the sdk toolchain by reverting their own sdk wrapper scripts and to
simulate an external toolchain build copying what is done in the
toolchain target makefile.
This handle compilation error and warning caused by not using fortify
header on building packages.
Fixes: 006e52545d14 ("CI: build: add support to fallback to sdk for external toolchain") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
add help text for `TARGET_SQUASHFS_BLOCK_SIZE` to match the only valid
settings accepted by `mksquashfs4` ("block size not power of two or not
between 4096 and 1Mbyte") thus for this setting in "KB", the set:
`4, 8, 16, 32, 64, 128, 256, 512, 1024`
replace `squashfs-lzma` with `squashfs` in the description for
`TARGET_ROOTFS_SQUASHFS` because it has various compressions, and not
just lzma as it did in the past
Shiji Yang [Tue, 29 Nov 2022 10:13:38 +0000 (18:13 +0800)]
ath79: optimize the firmware recipe for Netgear NAND devices
1. Drop useless character '0xff' before fake filesystem header.
2. Reduce useless padding to shrink the size of the sysupgrade image.
3. Do not check the size of sysupgrade image. It does not make sense to
check the size of a compressed package.
4. Do not take the size of netgear header into account because it will
not be written to Flash.
5. Use the default lzma compression dictionary parameter '-d24' to get
better performance.
Tested on Netgear R6100 Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hauke Mehrtens [Mon, 5 Dec 2022 23:17:35 +0000 (00:17 +0100)]
e2fsprogs: Fix CVE-2022-1304
This fixes CVE-2022-1304:
An out-of-bounds read/write vulnerability was found in e2fsprogs 1.46.5.
This issue leads to a segmentation fault and possibly arbitrary code
execution via a specially crafted filesystem.
Flash instruction:
1. Serve the initramfs.img using a TFTP server with address 10.10.10.3.
2. Interrupt the uboot startup process via UART.
3. Select "System Load Linux to SDRAM via TFTP" item.
4. (important) Back up firmware(mtd7) partitions with:
dd if=/dev/mtd7 of=/tmp/firmware.bin
and then download the firmware.bin image via SCP.
5. Flash the OpenWrt sysupgrade firmware.
Recovery stock firmware:
1. Transfer the firmware.bin image to the device.
2. Flash the image with:
mtd write firmware.bin firmware
Signed-off-by: Alex Hansen <mralexh123@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Jo-Philipp Wich [Mon, 5 Dec 2022 14:58:41 +0000 (15:58 +0100)]
firewall4: update to latest Git HEAD
700a925 fw4: prevent null access when no ipsets are defined 6443ec7 config: drop input traffic by default 119ee1a ruleset: drop ctstate invalid traffic for masq-enabled zones
John Thomson [Wed, 9 Nov 2022 23:55:11 +0000 (09:55 +1000)]
ramips: mt7621: mikrotik 760igs (hEX S) fix SFP
This device uses an AR8031/AR8033 chip to convert SoC gmac1
RGMII to 1000base-x or sgmii for the SFP fibre cage.
The SFP cage requires phy-mode rgmii-rxid, and without it will not
recieve any packets: ethtool -S sfp rx_fcs_errors will increase when
packets should be being received, but no other _rx counters will change.
Fixes: c77858aa792 ("ramips: mt7621-dts: change phy-mode of gmac1 to rgmii") Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Daniel Golle [Mon, 5 Dec 2022 23:10:29 +0000 (23:10 +0000)]
mediatek: mt7623: build mt6577_auxadc driver into kernel
Set CONFIG_MT6577_AUXADC=y as otherwise reading temperature of the
thermal-zone doesn't work on MT7623 (it does work fine without this
driver on MT7622 and MT7986).
Fixes: f2ae4e2f8c ("mediatek: clean up platform kernel modules") Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Fri, 2 Dec 2022 12:54:52 +0000 (12:54 +0000)]
trusted-firmware-a.mk: fix build with binutils 2.39
Starting from version 2.39 binutils now warns about sections with rwx
permissions. While this is generally desirable it breaks building
ARM TrustedFirmware-A bl2 which treats warnings as errors.
Disable the warning/error for now to fix build.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
1st image is "Kernel" and 2nd is "app" when booted from 1st image.
In OpenWrt, those 2x partitions are combined to "firmware" with
undefined (empty) areas (0x7e0000-0x7fffff, 0xf80000-0xf8ffff).
The size of an OS image partition is 0x780000 (7680 KiB = 7.5 MiB), so
check-size for initramfs-factory image needs to be called with the size.
CI: build: fix matching for openwrt release branch for toolchain parsing
The current match logic doesn't handle test for push events related to
stable release (example openwrt-22.03) but only fork with the related
prefix (example openwrt-22.03-fixup)
Fix wrong matching and while at it also add extra checks to other
matching (check if the branch name actually start with the requested
prefix)
Fixes: e24a1e6f6d7f ("CI: build: add support for external toolchains from stable branch") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CI: fix matching for openwrt release branch for container selection
The current match logic doesn't handle test for push events related to
stable release (example openwrt-22.03) but only fork with the related
prefix (example openwrt-22.03-fixup)
Fix wrong matching and while at it also add extra checks to other
matching (check if the branch name actually start with the requested
prefix)
Fixes: abe8a4824210 ("CI: build: add support for per branch tools container") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support to push per branch container tools.
For anything not official stick to latest tag that correspond to test
run from master.
If we are testing something for one of the openwrt stable branch, parse
the branch name or the tag and push dedicated tools containers.
To use the stable container for local testing the branch needs to have
the prefix openwrt-[0-9][0-9].[0-9][0-9] (example openwrt-21.02-fixup)
Any branch that will match this pattern openwrt-[0-9][0-9].[0-9][0-9]
will refresh the tools container with the matching tag.
(example branch openwrt-22.03 -> tools:openwrt-22.03)
(example branch openwrt-22.03-test -> tools:openwrt-22.03)
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
iucode-tool: fix compile error with musl libc and USE_CPUID_DEVICE
Add patch to fix compilation error with USE_CPUID_DEVICE enabled and musl
used as libc. Musl doesn't add limits.h header by default and this is
required if USE_CPUID_DEVICE is used.
The package currently compile because fortify headers include limits.h
by default.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Senis John [Sat, 19 Nov 2022 03:30:54 +0000 (11:30 +0800)]
ramips: add support for HiWiFi HC5611
CPU: MediaTek MT7628AN @ 575 MHz
Flash: 16 MB
RAM: 128 MB
Ethernet: 10/100Mbps x 1
Wlan: 300 Mbps
USB: USB 2.0 x 1
LED: red/green x 1
Button: reset x 1
1. Open https://www.hiwifi.wtf/, Get Cloud token and unlock ssh
2. Upload the openwrt firmware to the router via SCP
3. Login the router via SSH
4. Run `mtd -r write path_to_firmware.bin firmware`
I have tested on my device.
- The LED will display RED on power-on, After system start completed, trun GREEN
- Reset button working now. Long press after 5s will reset factory. Short press less 1s will reboot the device
- USB can working under official u-boot
That currently leads to `CONFIG_NET_DSA_MV88E6XXX=m` in images produced
by buildbots due to `CONFIG_ALL_KMODS=y` config option being used in
those builds, which leads to a broken LAN bridge network on several
devices.
References: https://lists.infradead.org/pipermail/openwrt-devel/2022-December/039950.html Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hauke Mehrtens [Sat, 3 Dec 2022 02:04:40 +0000 (03:04 +0100)]
CI: Build all boards and testing kernel
This adds options to build all boards of a selected target and an
additional option to build the testing kernel instead of the normal
kernel. This can be used by other trigger work flows.
Hauke Mehrtens [Sat, 5 Nov 2022 13:27:11 +0000 (14:27 +0100)]
CI: Allow building with internal toolchain
This adds an option to build with internal toolchain. This can be used
to build targets which are currently not build by the OpenWrt build bots
and which needs their own toolchain build for every build.
Building the toolchain takes about 30 minutes compared to using the
external toolchain which takes some seconds.
Hauke Mehrtens [Tue, 1 Nov 2022 18:10:01 +0000 (19:10 +0100)]
CI: Extract the OpenWrt building to own sub workflow
Extract the building of OpenWrt into an own workflow which is then
triggered by the kernel.yml and packages.yml workflow with different
inputs. This allows us to share much of the code of the workflow.
Stijn Segers [Fri, 2 Dec 2022 12:36:20 +0000 (13:36 +0100)]
mvebu: switch default kernel to 5.15
In light of https://github.com/openwrt/openwrt/issues/11077, switch mvebu
to 5.15 which has been the testing kernel on this target since April - over
half a year.
realtek: refactor keep vlan tag setup, fix tagged forwarding
The code in dsa.c:rtl83xx_port_enable() was trying to set
vlan_port_tag_sts_ctrl while dealing with differences between SoCs.
However, not only that register has a different address, the register
structure and even the 2-bit value semantic changes for each SoC.
The vlan_port_tag_sts_ctrl field was dropped and converted into a
vlan_port_keep_incoming_tag_set() function that abstracts the different
between SoCs. The macro referencing that register migrated to the SoC
specific c file as it will be privately used by each file.
All magic numbers were converted into macros using BITMASK and
FIELD_PREP.
The vlan_port_tag_sts_ctrl debugfs was dropped for now as it is already
broken for rtl93xx. The best place for SoC specific code might be in each
respective c file and not in if/else clauses.
The final result is:
rtl838x: set ITAG_STS=TAGGED, same as before
rtl839x: set ITAG_STS=TAGGED instead of IGR_P_ITAG_KEEP=0x1, fixing
forwarding of tagged packets
rtl930x: set EGR_ITAG_STS=TAGGED instead of IGR_P_ITAG=0x1, possibly
fixing forwarding of tagged packets
rtl931x: set EGR_ITAG_STS=TAGGED instead of OTPID_KEEP=0x1, possibly
fixing forwarding of tagged packets
Without (EGR_)ITAG_STS=TAGGED, at least for rtl839x, forwarded packets
will drop the vlan tag while packets from the CPU will still have the
correct tag.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Olliver Schinagl [Mon, 31 Oct 2022 13:02:52 +0000 (14:02 +0100)]
realtek: Fix rtl930x speed status accessor
The rtl930x speed status registers require 4 bits to indicate the speed
status. As such, we want to divide by 8. To make things consistent with
the rest of this code, use a bitshift however.
This bug probably won't affect many users yet, as there aren't many
rtl930x switches in the wild yet with more then 10 ports, and thus a
low-impact bugfix.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[also fix port field extraction] Signed-off-by: Sander Vanheule <sander@svanheule.net>
CI: labeler: fix wrong label for pr targeting stable branch
The label used for stable branch is in the form of
release/[0-9][0-9].[0-9][0-9]
Currently we apply the name of the target branch as the label, fix this
and correctly use the current label.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support to tag pr targeting stable branch matching the simple regex
of openwrt-[0-9][0-9].[0-9][0-9]. The tag that will be added will match
the pr target branch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Tue, 29 Nov 2022 19:38:21 +0000 (19:38 +0000)]
uboot-mediatek: bpi-r3: raise CONFIG_LMB_MAX_REGIONS to 64
Raise CONFIG_LMB_MAX_REGIONS to 64 as there are going to be more than
8 (the default value) reserved regions to allow supporting offloading
Wireless-to-Ethernet traffic on MT7986.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Sun, 27 Nov 2022 12:33:31 +0000 (12:33 +0000)]
dnsmasq: add option to expose additional paths to jail
Add new UCI list 'addn_mount' allowing the expose additional filesystem
paths to the jailed dnsmasq process. This is useful e.g. in case of
manually configured includes to the configuration file or symlinks
pointing outside of the exposed paths as used by e.g. the safe-search
package in the packages feed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6
The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP
with a miniPCIe slot for a LTE modem.
The wAP R AC is similar to the wAP AC but with the miniPCIe slot.
The wAP R AC requires installing a LTE modem.
The wAP LTE and wAP LTE6 comes with a LTE modem installed.
See https://mikrotik.com/product/wap_r_ac for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- CPU: 4x ARM Cortex A7
- RAM: 128MB
- Storage: 16MB NOR flash
- Wireless:
- Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna
- Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports
one with 802.3af/at PoE in
- 1x Mini PCI-E port (USB2)
Installation:
Boot the initramfs image via TFTP, then flash the sysupgrade image using
sysupgrade. Details at https://openwrt.org/toh/mikrotik/common.
Swconfig isn't used by this target and can be disabled for
this reason. Airoha doesn't even have an Ethernet driver.
In the future, this target should get a DSA driver.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Pawel Dembicki [Sat, 29 Oct 2022 20:59:50 +0000 (22:59 +0200)]
layerscape: kmod-ppfe: Use ppfe driver as module
In 8274451cb86 kmod-ppfe was changed to built-in because CONFIG_FSL_PPFE
was binary. In 5.10 and 5.15 kernel, PPFE driver can be build as module.
This patch switch kmod-ppfe from build-in to loadable module.
Loadable module helps to avoid hazard: driver is looking for firmware
file before mount root.
Pawel Dembicki [Sat, 29 Oct 2022 21:42:03 +0000 (23:42 +0200)]
layerscape: Fix SPI-NOR issues with vendor patches
For some reason LS1012A and LS1046A devboards don't work well with
Spansion SPI NOR flash. It cause read and write errors like:
[ 27.285887] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x025ae000
[ 27.468922] jffs2: Newly-erased block contained word 0x0 at offset 0x02573000
[ 27.502615] jffs2: Newly-erased block contained word 0xe723f41e5823f110 at offset 0x02572000
[ 27.541550] jffs2: Newly-erased block contained word 0x1a7d266ee6 at offset 0x02571000
[ 27.577195] jffs2: Newly-erased block contained word 0x5d000bae8d52fec6 at offset 0x02570000
[ 27.611800] jffs2: Newly-erased block contained word 0x63515aee63515a4b at offset 0x0256f000
[ 27.651749] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0256e000
[ 27.825593] jffs2: Newly-erased block contained word 0xc20031985 at offset 0x0252e000
NXP have found workarround and applied in their vendor kernel version.
They force 1x tx and 1x rx lines in qspi. That method fix issues.
This patch ports patches from NXP LSDK tree.
Will Moss [Thu, 10 Nov 2022 19:55:11 +0000 (19:55 +0000)]
ath79: D-Link DIR-825 B1 add factory.bin recipe
- Bring back factory.bin image which was missing after porting device to ath79 target
- Use default sysupgrade.bin image recipe
- Adjust max image size according to new firmware partition size after
"ath79: expand rootfs for DIR-825-B1 with unused space (aca8bb5)" changes
- Remove support of upgrading from version 19.07, because partition size changes mentioned above
MAC addresses are labeled as ETH, 2.4G, and 5GHz
Only one Vendor MAC address in flash
eth0 ETH *:fb art 0x0
phy1 2.4G *:fc ---
phy0 5GHz *:fd ---
**Serial Access:**
the RX line on the board for UART is shorted to ground by resistor R176
therefore it must be removed to use the console
but it is not necessary to remove to view boot log
optionally, R175 can be replaced with a solder bridge short
the resistors R175 and R176 are next to the UART RX pin at J10
**Installation:**
2 ways to flash factory.bin from OEM:
Method 1: Firmware upgrade page:
OEM webpage at 192.168.1.1
username and password "admin"
Navigate to "Firmware Upgrade" page from left pane
Click Browse and select the factory.bin image
Upload and verify checksum
Click Continue to confirm and wait 3 minutes
Method 2: Serial to load Failsafe webpage:
After connecting to serial console and rebooting...
Interrupt uboot with any key pressed rapidly
execute `run failsafe_boot` OR `bootm 0x9fd70000`
wait a minute
connect to ethernet and navigate to
"192.168.1.1/index.htm"
Select the factory.bin image and upload
wait about 3 minutes
**Return to OEM:**
If you have a serial cable, see Serial Failsafe instructions
otherwise, uboot-env can be used to make uboot load the failsafe image
ssh into openwrt and run
`fw_setenv rootfs_checksum 0`
reboot, wait 3 minutes
connect to ethernet and navigate to 192.168.1.1/index.htm
select OEM firmware image from Engenius and click upgrade
**TFTP recovery:**
Requires serial console, reset button does nothing
rename initramfs to 'vmlinux-art-ramdisk'
make available on TFTP server at 192.168.1.101
power board, interrupt boot
execute tftpboot and bootm 0x81000000
NOTE: TFTP is not reliable due to bugged bootloader
set MTU to 600 and try many times
if your TFTP server supports setting block size
higher block size is better.
**Format of OEM firmware image:**
The OEM software of EAP1750H is a heavily modified version
of Openwrt Kamikaze. One of the many modifications
is to the sysupgrade program. Image verification is performed
simply by the successful ungzip and untar of the supplied file
and name check and header verification of the resulting contents.
To form a factory.bin that is accepted by OEM Openwrt build,
the kernel and rootfs must have specific names...
and begin with the respective headers (uImage, squashfs).
Then the files must be tarballed and gzipped.
The resulting binary is actually a tar.gz file in disguise.
This can be verified by using binwalk on the OEM firmware images,
ungzipping then untaring.
Newer EnGenius software requires more checks but their script
includes a way to skip them, otherwise the tar must include
a text file with the version and md5sums in a deprecated format.
The OEM upgrade script is at /etc/fwupgrade.sh.
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
Note on PLL-data cells:
The default PLL register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
Edward Chow [Tue, 22 Nov 2022 10:49:21 +0000 (18:49 +0800)]
ath79: calibrate TP-LINK TL-WR2543ND with nvmem
Driver for and pci wlan card now pull the calibration data from the nvmem
subsystem.
This allows us to move the userspace caldata extraction for the pci-e ath9k
supported wifi into the device-tree definition of the device.
The wifi mac address remains correct after these changes, because When both
"mac-address" and "calibration" are defined, the effective mac address
comes from the cell corresponding to "mac-address" and
mac-address-increment.
Shiji Yang [Sun, 20 Nov 2022 03:15:16 +0000 (11:15 +0800)]
scripts: remove redundant character '0x0a' from Linksys image signature
The redundant character '0x0a' after the 192 bytes '0x00' padding broke
the factory image. We need to remove it to make things work again.
Fixes: e6769d11f3 scripts: fix missing character '0' issue in linksys image Tested-by: Tony Butler <spudz76@gmail.com> Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Nick Hainke [Wed, 16 Nov 2022 07:48:02 +0000 (08:48 +0100)]
wolfssl: update to v5.5.3
Remove "200-ecc-rng.patch" because it was upstramed by:
https://github.com/wolfSSL/wolfssl/commit/e2566bab2122949a6a0bb2276d0a52598794d7d0
Refreshed "100-disable-hardening-check.patch".
Rosen Penev [Tue, 22 Nov 2022 01:02:31 +0000 (17:02 -0800)]
nls.mk: fixup cmake packages
Instead of manually overriding every cmake package that uses iconv or
gettext's paths, add the prefix in here so that at least FindIconv.cmake
works. Fixes compilation with BUILD_NLS.
ipq806x: disable cache and fabric devfreq driver to improve stability
It was tested that cache scaling currently cause instability problem.
This is probably caused by a latent misconfiguration that cause the L2
cache to be sourced from the wrong source and runs at an unstable freq
compared to the original QSDK fw.
To improve stability while the problem is bisected, disable the devfreq
drivers with minimal perf penality.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Daniel Golle [Thu, 17 Nov 2022 02:03:59 +0000 (02:03 +0000)]
ipq40xx: remove '-fit' string from kernel filenames
The type of those images is already distinguishable by the '.itb'
extension, there is no need for an additional '-fit' string in the
filenames. Remove it to behave more like other targets.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Thu, 17 Nov 2022 01:52:50 +0000 (01:52 +0000)]
ipq40xx: remove 'nand-' string from image filenames
Only on the ipq40xx subtarget different filenames were used for NAND-
based devices. This is unneeded, confusing and breaks downstream tools
such as luci-app-attendedsysupgrade and auc.
Remove the 'nand-' string from image filenames to fix that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
projects / thirdparty / openwrt.git / log
